Configurations with multiple codecs attached to the platform are
supported but only if each from the set is different. Add new field
representing the 'Unique ID' so that codecs that share Vendor and Part
IDs can be differentiated and thus enabling support for such
configurations.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230519201711.4073845-6-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In the BE hw_params configuration, the existing code checks if any of the
existing FEs are prepared, running, paused or suspended - and skips the
configuration in those cases. This allows multiple calls of hw_params
which the ALSA state machine supports.
This check is not handled for the prepare stage, which can lead to the
same BE being prepared multiple times. This patch adds a check similar to
that of the hw_params, with the main difference being that the suspended
state is allowed: the ALSA state machine allows a transition from
suspended to prepared with hw_params skipped.
This problem was detected on Intel IPC4/SoundWire devices, where the BE
dailink .prepare stage is used to configure the SoundWire stream with a
bank switch. Multiple .prepare calls lead to conflicts with the .trigger
operation with IPC4 configurations. This problem was not detected earlier
on Intel devices, HDaudio BE dailinks detect that the link is already
prepared and skip the configuration, and for IPC3 devices there is no BE
trigger.
Link: https://github.com/thesofproject/sof/issues/7596
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Link: https://lore.kernel.org/r/20230517185731.487124-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org
These registers enable the HDaudio DMA hardware to split/merge data
from different PDIs, possibly on different links.
This capability exists for all types of HDaudio extended links, but
for now is only required for SoundWire. In the SSP/DMIC case, the IP
is programmed by the DSP firmware.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com
Reviewed-by: Rander Wang <rander.wang@intel.com
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com
Link: https://lore.kernel.org/r/20230512174611.84372-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org
Same functionality as for DMIC/SSP with different ID.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Reviewed-by: Rander Wang <rander.wang@intel.com
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com
Link: https://lore.kernel.org/r/20230512174611.84372-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org
The bulk of the commits here are for the conversion of drivers to use
void remove callbacks but there's a reasonable amount of other stuff
going on, the pace of development with the SOF code continues to be high
and there's a bunch of new drivers too:
- More core cleanups from Morimto-san.
- Update drivers to have remove() callbacks returning void, mostly
mechanical with some substantial changes.
- Continued feature and simplification work on SOF, including addition
of a no-DSP mode for bringup, HDA MLink and extensions to the IPC4
protocol.
- Hibernation support for CS35L45.
- More DT binding conversions.
- Support for Cirrus Logic CS35L56, Freescale QMC, Maxim MAX98363,
nVidia systems with MAX9809x and RT5631, Realtek RT712, Renesas R-Car
Gen4, Rockchip RK3588 and TI TAS5733.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmRGdEsACgkQJNaLcl1U
h9BNVAf+Ijupg3dhAl6847v1PRYXkYK6YjAayhNd0xRoRePKnnv1zkrsXSBzxZUM
8KHpQDUJyfQbPnE2JRmr1WfHSoNDl/NXdJl+lefPBgol5bzxRji68hDPGjA0645o
R6vzrqLNw8mh3jwptXfEpQfKH8tIvwOeMeLkncDvsm0ZCUR2GhYnjB1g82ih0ssx
lvh36PdCRF0e/ruHxkiVn9b/riID65oTRkN6IxJqoPnqJZVyCiqmiJcfWePpaPir
4R9Dyk+REos/aCLdne1g6H21Tgi0td+blv6empqwdEXG41VSdRMTrOZb1ZISKmpF
ggPbKsk9BjJFBCewllHXJ0YEcBp9/g==
=TVxt
-----END PGP SIGNATURE-----
Merge tag 'asoc-v6.4' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v6.4
The bulk of the commits here are for the conversion of drivers to use
void remove callbacks but there's a reasonable amount of other stuff
going on, the pace of development with the SOF code continues to be high
and there's a bunch of new drivers too:
- More core cleanups from Morimto-san.
- Update drivers to have remove() callbacks returning void, mostly
mechanical with some substantial changes.
- Continued feature and simplification work on SOF, including addition
of a no-DSP mode for bringup, HDA MLink and extensions to the IPC4
protocol.
- Hibernation support for CS35L45.
- More DT binding conversions.
- Support for Cirrus Logic CS35L56, Freescale QMC, Maxim MAX98363,
nVidia systems with MAX9809x and RT5631, Realtek RT712, Renesas R-Car
Gen4, Rockchip RK3588 and TI TAS5733.
Firstly, fix the distribution between public and private headers.
Otherwise, some of the already public macros wouldn't actually work, and
the SNDRV_EMU10K1_IOCTL_DBG_READ result for Audigy would be useless.
Secondly, add condition code registers for Audigy. These are just
aliases for selected constant registers, and thus are generation-
specific. At least A_CC_REG_ZERO is actually correct ...
Finally, shuffle around some defines to more logical places while at it,
and fix up some more comments.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230422161021.1143903-7-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For documentation purposes and later use.
Some pre-existing but (mostly) unused definitions were renamed for
consistency.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230422161021.1143903-6-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Firstly, remove the FXWC_* defines - the comment on FXWC implies that
the relevant defines are the (A_)EXTOUT_* ones. It's unclear where this
came from - it was in the initial ALSA import, but neither the driver
from Creative nor kX-project have these defines.
Secondly, remove A_HR, which made plain no sense (was unused, and
clashed with FXRT). Amends commit cbb7d8f9b7 ("emu10k1: Update
registers defines for the Audigy 2/emu10k2.5").
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230422161021.1143903-5-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move comments to better locations, de-duplicate, fix/remove incorrect/
outdated ones, add new ones, and unify spacing somewhat.
While at it, also add testing credits for Jonathan Dowland (SB Live!
Platinum) and myself (E-MU 0404b).
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230422161021.1143903-2-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Unlike the Alice2 chips used on 1st generation E-MU cards, the
Tina/Tina2 chips used on the 2nd gen cards have only six GPIN pins,
which means that we need to use a smaller mask. Failure to do so would
falsify the read data if the FPGA tried to raise an IRQ right at that
moment. This wasn't a problem so far, as we didn't actually enable FPGA
IRQs, but that's going to change soon.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230422132430.1057490-1-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As the register definition clearly states, this is a 16-bit register,
yet we did all accesses as 32-bit. The writes in particular would have
the potential to clear the TIMER register (depending on how the bus/card
actually handles the too long writes).
This commit also introduces a separate define A_GPIO which aliases
A_IOCFG, which better reflects the distinct usage on E-MU cards.
This is done in the same commit to keep the churn down, as we're
touching all involved lines anyway.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230421141006.1005539-2-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Assert the validity of the registers and values, as them being out of
range would indicate an error in the driver. Consequently, don't bother
returning error codes; they were ignored everywhere anyway.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230421141006.1005539-1-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Detach it better from the main PCM driver, which it really doesn't have
much in common with.
In particular, this moves the interrupt handler implementation into
p16v.c, and makes it access the substream runtime status more directly,
so it doesn't need to abuse structs snd_emu10k1_pcm and
snd_emu10k1_voice any more.
We don't need private pcm runtime data at all, as the only thing it was
used for (except the back-link to the substream) was the `running` flag.
So store that directly in runtime->private_data.
This somewhat radical strip-down shows that this driver contains some
complexity that was never actually utilized. I suppose the right way to
fully utilize the hardware in a simple way would be introducing more
substreams. This wouldn't require any of the removed code.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230421141006.1005452-7-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The use of the variable was removed in commit 2b637da5a1 ("clean up
card features"). That commit also broke user space (the ioctl
structure), at which point the defines became meaningless, so I don't
think purging them is a problem.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230421141006.1005452-3-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
extin_mask and extout_mask are used only by the SbLive! microcode, so
they have no effect on Audigy.
Eliminate fxbus_mask entirely, as it wasn't actually used for anything.
As a drive-by, remove the pointless pad1 field from struct
snd_emu10k1_fx8010 - it is not visible to user space, so it has no
binary compatibility constraints.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230421141006.1005509-1-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The auto-silencer supports two modes: "thresholded" to fill up "just
enough", and "top-up" to fill up "as much as possible". The two modes
used rather distinct code paths, which this patch unifies. The only
remaining distinction is how much we actually want to fill.
This fixes a bug in thresholded mode, where we failed to use new_hw_ptr,
resulting in under-fill.
Top-up mode is now more well-behaved and much easier to understand in
corner cases.
This also updates comments in the proximity of silencing-related data
structures.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20230420113324.877164-1-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Rename the mixer source defines from CS35L56_INPUT_SRC_SWIRE_RXn
to CS35L56_INPUT_SRC_SWIRE_DP1_CHANNELn to match the latest
datasheet.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230418144309.1100721-5-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The mixer source index value for SDW2RX1 is different between
A1 and B0 silicon. As the driver doesn't provide a DAI for SDW2
just remove it as a mixer source option.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230418144309.1100721-4-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Reduce SDW1 to 4 channels and remove the controls for SDW1
TX5 and TX6.
The TX5 and TX6 channels have been removed from B0 silicon.
There is no need to support them on A1 silicon.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230418144309.1100721-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC need to use card->mutex with _INIT or _RUNTIME,
but there is no helper function for it.
This patch adds its helper function and use it.
Because people might misunderstand that _init() is mutex initialization,
this patch renames _INIT to _ROOT and adds new
snd_soc_card_mutex_lock_root() for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87a5zlx3tw.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
soc-pcm.c has snd_soc_dpcm_mutex_lock/unlock(),
but other files can't use it because it is static function.
It requests snd_soc_pcm_runtime as parameter (A), but sometimes we
want to use it by snd_soc_card (B).
(A) static inline void snd_soc_dpcm_mutex_lock(struct snd_soc_pcm_runtime *rtd)
{
mutex_lock_nested(&rtd->card->pcm_mutex, rtd->card->pcm_subclass);
} ^^^^^^^^^
(B) mutex_lock_nested(&card->pcm_mutex, card->pcm_subclass);
^^^^
We want to use it with both "rtd" and "card" for dapm lock/unlock.
To enable it, this patch uses _Generic macro.
This patch makes snd_soc_dpcm_mutex_{un}lock() global function, and use it on
each files.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87bkk1x3ud.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
soc.h has snd_soc_dapm_mutex_lock/unlock() definition and
many drivers are using it, but soc-dapm.c is not.
1st reason is snd_soc_dapm_mutex_lock/unlock() requests
snd_soc_dapm_context pointer as parameter (A), but sometimes soc-dapm.c
needs to use snd_soc_card (B).
(A) static inline void snd_soc_dapm_mutex_lock(struct snd_soc_dapm_context *dapm)
{
mutex_lock_nested(&dapm->card->dapm_mutex, SND_SOC_DAPM_CLASS_RUNTIME);
} ^^^^^^^^^^
(B) mutex_lock_nested(&card->dapm_mutex, SND_SOC_DAPM_CLASS_RUNTIME);
^^^^
2nd reason is it want to use SND_SOC_DAPM_CLASS_INIT for mutex_lock_nested(),
but helper is using _RUNTIME (A).
The conclusion is we want to use "dapm vs card" and "_RUNTIME vs _INIT"
for dapm lock/unlock. To enable this selfish request, this patch uses
_Generic macro. We can use snd_soc_dapm_mutex_lock/unlock() for both
dapm and card case.
snd_soc_dapm_mutex_lock(dapm); snd_soc_dapm_mutex_unlock(dapm);
snd_soc_dapm_mutex_lock(card); snd_soc_dapm_mutex_unlock(card);
Current soc-dapm.c is using both mutex_lock() and mutex_lock_nested().
This patch handles mutex_lock() as mutex_lock_nested(..., 0),
in other words, handles below as same.
mutex_lock(&card->dapm_mutex);
mutex_lock_nested(&card->dapm_mutex, SND_SOC_DAPM_CLASS_INIT);
Because people might misunderstand that _init() is mutex initialization,
this patch renames _INIT to _ROOT and adds new
snd_soc_dapm_mutex_lock_root() for it.
This patch also moves snd_soc_dapm_subclass definition from soc-dapm.h
to soc.h to keep related code together.
Because very complex soc.h vs soc-dapm.h relationship,
it is difficult/impossible to define these helper into soc-dapm.h.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87cz4hx3v0.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Check during cs35l56_system_resume() whether the firmware patch must
be applied again.
The FIRMWARE_MISSING flag in the PROTECTION_STATUS register indicates
whether the firmware has been patched.
In non-secure mode the FIRMWARE_MISSING flag is cleared at the end of
dsp_work(). If it is set after system-resume we know that dsp_work()
must be run again.
In secure mode the pre-OS loader will have done the secure patching
and cleared the FIRMWARE_MISSING flag. So this flag does not tell us
whether firmware memory was lost. But the driver could only be
downloading non-secure tunings, which is always safe to do.
If the driver has control of RESET we will have asserted it during
suspend so the firmware patch will have been lost. The driver would only
have control of RESET in non-secure mode.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/168122674550.26.8545058503709956172@mailman-core.alsa-project.org
Signed-off-by: Mark Brown <broonie@kernel.org>
For SoundWire usages, we need to use the global eml_lock to
serialize/protect all accesses to shared registers. Due to the split
implementation across two subsystems, we need to pass a pointer
around.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230404104127.5629-19-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For DMIC and SSP, the DSP will be responsible for programming the
blobs and link registers.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230404104127.5629-18-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Small helpers to make DAI ops simpler.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230404104127.5629-17-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Each SoundWire peripheral can be programmed from the manager side
either with a regular command FIFO, or with the HDaudio CORB/RIRB
DMA-based mechanism. The mapping between SoundWire peripheral and SDI
address is handled with the LSDIID register.
This mapping only works of course if each peripheral has a unique
address across all links. This has already been enforced in previous
Intel contributions allowing for an IDA-based solution for the device
number allocation.
The checks on the dev_num are handled at the SoundWire level, but the
locking is handled at the hda-mlink level.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230404104127.5629-16-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This helper is an optimization where sync_go is only called when the
cmdsync field is actually set to a non-zero value.
Since this is also only used by SoundWire for now, only expose the
_unlocked version.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230404104127.5629-15-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The multi-link synchronization uses the same concept and registers,
but moved to the HDAudio extended links.
Add helpers for sync_arm and sync_go which are the basic for the bus
reset, bank switch and clock stop.
Since SoundWire is the only user of those helpers, only expose the
_unlocked versions for now.
Note that SYNCGO is a write-only bit, so no error can be reported. We
still return 0 for compatibility with the SoundWire stream management
headers.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230404104127.5629-14-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
These helpers configure the ratio between the base clock and the
hardware signal used for link synchronization.
The SYNCPRD is written before the first sublink is powered-up. The
SYNCPU bit is set, but it will only be cleared after the link is
powered-up, hence the implementation with a set/wait pattern.
These helpers are currently only needed by SoundWire support, where
the lock is taken at a higher level, so only the _unlocked versions
are exposed for now.
Note that the _wait_bit() implementation is similar to previous
helpers in drivers/soundwire, but with sleep duration and timeout
aligned with hardware recommendations. If desired, this helper could
be modified in a second step with e.g. readl_poll_timeout().
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230404104127.5629-13-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When INTC is set, LCTL exposes INTEN and INTSTS fields.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230404104127.5629-12-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This is needed for SoundWire integration.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230404104127.5629-11-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The updated SoundWire Intel driver will need to rely on Extended
HDaudio links for power management, but it doesn't need to be aware of
all the HDaudio structures. Add convenience helpers to avoid polluting
SoundWire drivers too much with HDaudio information.
Since the SoundWire/Intel solution already takes the lock at a higher
level, the _unlocked PM helpers are used.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230404104127.5629-10-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add helpers to program SPA/CPA bits, using a mutex to access the
shared LCTL register if required.
All links are managed with the same LCTLx.SPA bits. However there are
quite a few implementation details to be aware of:
Legacy HDaudio multi-links are powered-up when exiting reset, which
requires the ref_count to be manually set to one when initializing the
link.
Alternate links for SoundWire/DMIC/SSP need to be explicitly
powered-up before accessing the SHIM/IP/Vendor-Specific SHIM space for
each sublink. DMIC/SSP/SoundWire are all different cases with a
different device/dai/hlink relationship.
SoundWire will handle power management with the auxiliary device
resume/suspend routine. The ref_count is not necessary in this case.
The DMIC/SSP will by contrast handle the power management from DAI
.startup and .shutdown callbacks.
The SSP has a 1:1 mapping between sublink and DAI, but it's
bidirectional so the ref_count will help avoid turning off the sublink
when one of the two directions is still in use.
The DMIC has a single link but two DAIs for data generated at
different sampling frequencies, again the ref_count will make sure the
two DAIs can be used concurrently.
And last the SoundWire Intel require power-up/down and bank switch to
be handled with a lock already taken, so the 'eml_lock' is made
optional with the _unlocked versions of the helpers.
Note that the _check_power_active() implementation is similar to
previous helpers in sound/hda/ext, with sleep duration and timeout
aligned with hardware recommendations. If desired, this helper could
be modified in a second step with .e.g. readl_poll_timeout()
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230404104127.5629-9-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Extend hdac_ext_link to store information needed for ALT
links. Follow-up patches will include more functional patches for
power-up and down.
Note that this patch suggests the use of an 'eml_lock' to serialize
access to shared registers. SoundWire-specific sequence require the
lock to be taken at a higher level, as a result the helpers added in
follow-up patches will provide 'unlocked' versions when needed.
Also note that the low-level sequences with the 'hdaml_' prefix are
taken directly from the hardware specifications - naming conventions
included. The code will be split in two, with locking and linked-list
management handled separately to avoid mixing required hardware setup
and Linux-based resource management.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230404104127.5629-7-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some of the functions will be used for SoundWire enumeration and power
management, to avoid cycles in module dependencies and simplify
integration all the HDaudio multi-link needs to move to a dedicated
module.
Drop no longer needed headers at the same time.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230404104127.5629-6-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add new definitions for the HDaudio Extended link support,
specifically new registers for SoundWire, Intel DMIC and INTEL SSP
interfaces.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230404104127.5629-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_dai_link has params/num_params, but it is unclear that
params for what. This patch clarify it is params for Codec2Codec.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87o7o5c2lk.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The DSPless mode of the ASoC/SOF driver can be used for hardware
verification and debug on platforms with HDaudio codecs. The DSP mode is
still needed on existing platforms for SSP, DMIC, SoundWire interfaces
managed by the GP-DMA.
This mode is also helpful to compare the legacy HDaudio driver with the
ASoC/SOF driver wrt. codec management and handling. In theory we use the
same code but differences are sometimes seen on jack detection and event
handling.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20230404092115.27949-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For allowing the build without CONFIG_PM, add definitions of dummy
functions for snd_ac97_suspend() and snd_ac97_resume() without
CONFIG_PM, too.
Link: https://lore.kernel.org/r/20230330132847.12882-1-tiwai@suse.de
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Reviewed-by: Tasos Sahanidis <tasos@tasossah.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Current ASoC supports snd_soc_add_pcm_runtime(), but user need to
call it one-by-one if it has multi dai_links.
This patch adds snd_soc_add_pcm_runtimes() which supports multi
dai_links.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87h6u76nhq.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As PCM ack callback may handle the XRUN situation gracefully now,
change the indirect PCM helpers to give a proper error (-EPIPE).
Also, change the pointer callback helpers to deal with the XRUN error
properly, too.
This requires the PCM core change by the commit 8c721c53dd
("ALSA: usb-audio: Fix recursive locking at XRUN during syncing").
Link: https://lore.kernel.org/r/20230323065237.5062-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge series from Peter Ujfalusi <peter.ujfalusi@linux.intel.com>:
On a platform when the DSP is in use, we cannot select individual links
to use or not use the DSP, it is either all or none. On some audio
endpoint, like HDMI/DP, it is preferred to not use any processing in DSP
to reduce the latency and to allow bytestream pass-through (DTS, DD,
etc)
IPC4 introduces a new type of end-to-end connection within the DSP which
is using the host DMA and link DMA in a single buffer, working
back-to-back, passing the received data without looking at it or trying
to understand the format, content.
This mode reduces the latency and allows non PCM streams to be sent from
userspace.
The feature is enabled per PCM bases, signalled in topology.
Cezary Rojewski