Some of the FSI-attached SPI controllers cannot use the loop command in
programming the sequencer due to security requirements. Check the
devicetree compatibility that indicates this condition and restrict the
size for these controllers. Also, add more transfers directly in the
sequence up to the length of the sequence register.
Fixes: bbb6b2f986 ("spi: Add FSI-attached SPI controller driver")
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20200909222857.28653-6-eajames@linux.ibm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
All of the switches in N2_count_control in the counter configuration are
required to make the branch if not equal and increment command work.
Set them when using bneq+.
A side effect of this mode requires a dummy write to TDR when both
transmitting and receiving otherwise the controller won't start shifting
receive data.
It is likely not possible to avoid TDR underrun errors in this mode and
they are harmless, so do not check for them.
Fixes: bbb6b2f986 ("spi: Add FSI-attached SPI controller driver")
Signed-off-by: Brad Bishop <bradleyb@fuzziesquirrel.com>
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20200909222857.28653-4-eajames@linux.ibm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use a clock divider tuned to a 200MHz FSI bus frequency (the maximum). Use
of the previous divider at 200MHz results in corrupt data from endpoint
devices. Ideally the clock divider would be calculated from the FSI clock,
but that would require some significant work on the FSI driver. With FSI
frequencies slower than 200MHz, the SPI clock will simply run slower, but
safely.
Signed-off-by: Brad Bishop <bradleyb@fuzziesquirrel.com>
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20200909222857.28653-3-eajames@linux.ibm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The trailing <len> - 8 bytes of transfer data in this size range is no
longer ignored.
Fixes: bbb6b2f986 ("spi: Add FSI-attached SPI controller driver")
Signed-off-by: Brad Bishop <bradleyb@fuzziesquirrel.com>
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20200909222857.28653-2-eajames@linux.ibm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Chunyan Zhang <zhang.lyra@gmail.com>
Link: https://lore.kernel.org/r/20200910160706.5883-1-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
If we're sending bytes over SPI, we know the FIFO is empty at the
start of the transfer. There's no reason to wait for the interrupt
telling us to start--we can just start right away. Then if we
transmit everything in one swell foop we don't even need to bother
listening for TX interrupts.
In a test of "flashrom -p ec -r /tmp/foo.bin" interrupts were reduced
from ~30560 to ~29730, about a 3% savings.
This patch looks bigger than it is because I moved a few functions
rather than adding a forward declaration. The only actual change to
geni_spi_handle_tx() was to make it return a bool indicating if there
is more to tx.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200912111716.1.Ied5e843fad0d6b733a1fb8bcfb364dd2fa889eb3@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
This eliminates the following sparse warning:
drivers/spi/spi-bcm2835.c:78:14: warning: symbol 'polling_limit_us' was
not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Link: https://lore.kernel.org/r/20200912072211.602735-1-yanaijie@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi device tree lacks DMA
channels for DSPI, so naturally, the driver fails to probe:
[ 2.945302] fsl-dspi 2100000.spi: rx dma channel not available
[ 2.951134] fsl-dspi 2100000.spi: can't get dma channels
In retrospect, this should have been obvious, because LS2080A, LS2085A
LS2088A and LX2160A don't appear to have an eDMA module at all. Looking
again at their datasheets, the CTARE register (which is specific to XSPI
functionality) seems to be documented, so switch them to XSPI mode
instead.
Fixes: 0feaf8f5af ("spi: spi-fsl-dspi: Convert the instantiations that support it to DMA")
Reported-by: Qiang Zhao <qiang.zhao@nxp.com>
Tested-by: Qiang Zhao <qiang.zhao@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20200910121532.1138596-1-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We always toggle the chip select manually in spi-geni-qcom so that we
can properly implement the Linux API. There's no reason to program
this to the hardware on every transfer. Program it once at init and
be done with it.
This saves some part of a microsecond of overhead on each transfer.
While not really noticeable on any real world benchmarks, we might as
well save the time.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200912140730.2.I33e571179986850b4ec17042e813d0b08fb1b9c1@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
In commit 902481a78e ("spi: spi-geni-qcom: Actually use our FIFO") I
explained that the maximum size we could program the FIFO was
"mas->tx_fifo_depth - 3" but that I chose "mas->tx_fifo_depth()"
because I was worried about decreased bandwidth.
Since that time:
* All the interconnect patches have landed, making things run at the
proper speed.
* I've done more measurements.
This lets me confirm that there's really no downside of using the FIFO
more. Specifically I did "flashrom -p ec -r /tmp/foo.bin" on a
Chromebook and averaged over several runs.
Before: It took 6.66 seconds and 59669 interrupts fired.
After: It took 6.66 seconds and 47992 interrupts fired.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200912140730.1.Ie67fa32009b94702d56232c064f1d89065ee8836@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
It is redundant to do irqsave and irqrestore in hardIRQ context.
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Barry Song <song.bao.hua@hisilicon.com>
Link: https://lore.kernel.org/r/20200910100246.32696-1-song.bao.hua@hisilicon.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Broadcom QSPI driver now falls back to no MSPI_DEV support as the
default setting in the generic compatible string, explicit settings for
STB chips 7425, 7429, and 7435 can be removed.
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20200910152539.45584-4-ray.jui@broadcom.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add compatible string for BRCMSTB 7445 SoCs and indicate it has MSPI rev
support.
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20200910152539.45584-2-ray.jui@broadcom.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The variable ret is being initialized with a value that is
never read and it is being updated later with a new value. The
initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200910150410.750959-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Hello,
This cleans up some of the user code around calls to
dev_pm_opp_of_remove_table().
All the patches can be picked by respective maintainers directly except
for the last patch, which needs the previous two to get merged first.
These are based for 5.9-rc1.
Rajendra, Since most of these changes are related to qcom stuff, it
would be great if you can give them a try. I wasn't able to test them
due to lack of hardware.
Ulf, I had to revise the sdhci patch, sorry about that. Please pick this
one.
Diff between V1 and V2 is mentioned in each of the patches separately.
Viresh Kumar (8):
cpufreq: imx6q: Unconditionally call dev_pm_opp_of_remove_table()
drm/lima: Unconditionally call dev_pm_opp_of_remove_table()
drm/msm: Unconditionally call dev_pm_opp_of_remove_table()
mmc: sdhci-msm: Unconditionally call dev_pm_opp_of_remove_table()
spi: spi-geni-qcom: Unconditionally call dev_pm_opp_of_remove_table()
spi: spi-qcom-qspi: Unconditionally call dev_pm_opp_of_remove_table()
tty: serial: qcom_geni_serial: Unconditionally call
dev_pm_opp_of_remove_table()
qcom-geni-se: remove has_opp_table
drivers/cpufreq/imx6q-cpufreq.c | 10 ++--------
drivers/gpu/drm/lima/lima_devfreq.c | 6 +-----
drivers/gpu/drm/lima/lima_devfreq.h | 1 -
drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c | 14 +++++---------
drivers/gpu/drm/msm/disp/dpu1/dpu_kms.h | 1 -
drivers/gpu/drm/msm/dsi/dsi_host.c | 8 ++------
drivers/mmc/host/sdhci-msm.c | 14 +++++---------
drivers/spi/spi-geni-qcom.c | 13 +++++--------
drivers/spi/spi-qcom-qspi.c | 15 ++++++---------
drivers/tty/serial/qcom_geni_serial.c | 13 +++++--------
include/linux/qcom-geni-se.h | 2 --
11 files changed, 31 insertions(+), 66 deletions(-)
base-commit: f4d51dffc6
--
2.25.0.rc1.19.g042ed3e048af
In spidev_read() and spidev_write(), the variable status is being
initialized with a value that is never read and it is being updated
later with a new value. The initialization is redundant and can be
removed.
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/1599631704-53232-1-git-send-email-f.fangjian@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dev_pm_opp_of_remove_table() doesn't report any errors when it fails to
find the OPP table with error -ENODEV (i.e. OPP table not present for
the device). And we can call dev_pm_opp_of_remove_table()
unconditionally here.
While at it, create a new label and put clkname on errors.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/b77aa0bbe82a580508e321a34da488b4b27966d0.1598594714.git.viresh.kumar@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
dev_pm_opp_of_remove_table() doesn't report any errors when it fails to
find the OPP table with error -ENODEV (i.e. OPP table not present for
the device). And we can call dev_pm_opp_of_remove_table()
unconditionally here.
While at it, create a new label and put clkname on errors.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/ea0864d41277e61fa31d304fbd4cf9af6b314269.1598594714.git.viresh.kumar@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The series add support for the Sparx5 SoC SPI controller in the
spi-dw-mmio.c spi driver.
v5 changes:
- rx-sample-delay-ns documentation changes from Rob Herring:
- Drop superfluous type $ref
- Add default value = 0
v4 changes:
- Changed snps,rx-sample-delay-ns to snps,rx-sample-delay-ns
suggested by Rob Herring (rockchip also has this property).
- Added support for controller-level rx-sample-delay-ns value as
well as per SPI slave value (rockchip has controller-level property).
- Dropped internal mux in favor of suggested spi-mux to
control bus inteface selection.
v3 changes:
- Added mux support for controlling SPI bus interface. This is new mux
driver, bindings and added to sparx5 base DT.
- Removed "microchip,spi-interface2" property in favour of
"mux-controls" property in SPI controller (sparx5 only).
- Changed dw_spi_sparx5_set_cs() to use the mux control instead of
directly acessing "mux" register. Associated code/defines moved to mux
driver.
- Changed dw_spi_sparx5_set_cs() to match other similar functions in
signature and avoid explicit CS toggling.
- Spun off duplicated NAND device DT chunks into separate DT file.
v2 changes:
- Moved all RX sample delay into spi-dw-core.c, using
the "snps,rx-sample-delay-ns" device property.
- Integrated Sparx5 support directly in spi-dw-mmio.c
- Changed SPI2 configuration to per-slave "microchip,spi-interface2"
property.
- Added bindings to existing snps,dw-apb-ssi.yaml file
- Dropped patches for polled mode and SPI memory operations.
Lars Povlsen (6):
spi: dw: Add support for RX sample delay register
spi: dw: Add Microchip Sparx5 support
arm64: dts: sparx5: Add SPI controller and associated mmio-mux
dt-bindings: snps,dw-apb-ssi: Add sparx5 support, plus
rx-sample-delay-ns property
arm64: dts: sparx5: Add spi-nor support
arm64: dts: sparx5: Add spi-nand devices
.../bindings/spi/snps,dw-apb-ssi.yaml | 21 ++++++
arch/arm64/boot/dts/microchip/sparx5.dtsi | 47 ++++++++++++-
.../arm64/boot/dts/microchip/sparx5_nand.dtsi | 31 ++++++++
.../boot/dts/microchip/sparx5_pcb125.dts | 30 ++++++++
.../boot/dts/microchip/sparx5_pcb134.dts | 1 +
.../dts/microchip/sparx5_pcb134_board.dtsi | 16 +++++
.../boot/dts/microchip/sparx5_pcb135.dts | 1 +
.../dts/microchip/sparx5_pcb135_board.dtsi | 16 +++++
drivers/spi/spi-dw-core.c | 26 +++++++
drivers/spi/spi-dw-mmio.c | 70 ++++++++++++++++++-
drivers/spi/spi-dw.h | 3 +
11 files changed, 260 insertions(+), 2 deletions(-)
create mode 100644 arch/arm64/boot/dts/microchip/sparx5_nand.dtsi
--
2.27.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Use default supports_op() to support spi-[rt]x-bus-width properties.
And check dummy op's byte length instead of its bus width for output.
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Link: https://lore.kernel.org/r/20200826091852.519138-1-ikjn@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200901152713.18629-11-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200901152713.18629-10-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200901152713.18629-9-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200901152713.18629-8-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200901152713.18629-7-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200901152713.18629-6-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200901152713.18629-5-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20200901152713.18629-4-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200901152713.18629-3-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
If dma_request_chan() for TX channel fails with EPROBE_DEFER, the RX
channel would not be released and on next re-probe it would be requested
second time.
Fixes: 386119bc7b ("spi: sprd: spi: sprd: Add DMA mode support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Chunyan Zhang <zhang.lyra@gmail.com>
Link: https://lore.kernel.org/r/20200901152713.18629-1-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This has the following changes for the snps,dw-apb-ss DT bindings:
- Add "microchip,sparx5-spi" as the compatible for the Sparx5 SoC
controller
- Add the property "rx-sample-delay-ns"
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200824203010.2033-5-lars.povlsen@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds SPI support for the Sparx5 SoC, which is using the MMIO
Designware SPI controller.
The Sparx5 differs from the Ocelot version in these areas:
* The CS override is controlled by a new set of registers for
this purpose.
* The Sparx5 SPI controller has the RX sample delay register, and it
must be configured for the (SPI NAND) device on SPI2.
* The Sparx5 SPI controller has 2 different SPI bus interfaces on the
same controller (don't ask...). The "spi-mux" driver should be used
in conjunction with the SPI driver to select the appropriate bus.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Link: https://lore.kernel.org/r/20200824203010.2033-3-lars.povlsen@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This add support for the RX_SAMPLE_DLY register. If enabled in the
Designware IP, it allows tuning of the rx data signal by means of an
internal rx sample fifo.
The register is controlled by the rx-sample-delay-ns DT property,
which is defined per SPI slave as well on controller level.
The controller level rx-sample-delay-ns will apply to all slaves
without the property explicitly defined.
The register is located at offset 0xf0, and if the option is not
enabled in the IP, changing the register will have no effect. The
register will only be written if any slave defines a nonzero value
(after scaling by the clock period).
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Link: https://lore.kernel.org/r/20200824203010.2033-2-lars.povlsen@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There seems no reason to restrict testing to ARM, so remove this
constraint to improve test coverage.
Build-tested with allyesconfig on x86.
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Link: https://lore.kernel.org/r/20200904163709.110975-1-alex.dewar90@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
-----BEGIN PGP SIGNATURE-----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=v5QQ
-----END PGP SIGNATURE-----
Merge tag 'io_uring-5.9-2020-09-06' of git://git.kernel.dk/linux-block
Pull more io_uring fixes from Jens Axboe:
"Two followup fixes. One is fixing a regression from this merge window,
the other is two commits fixing cancelation of deferred requests.
Both have gone through full testing, and both spawned a few new
regression test additions to liburing.
- Don't play games with const, properly store the output iovec and
assign it as needed.
- Deferred request cancelation fix (Pavel)"
* tag 'io_uring-5.9-2020-09-06' of git://git.kernel.dk/linux-block:
io_uring: fix linked deferred ->files cancellation
io_uring: fix cancel of deferred reqs with ->files
io_uring: fix explicit async read/write mapping for large segments
Including:
- Three Intel VT-d fixes to fix address handling on 32bit, fix a
NULL pointer dereference bug and serialize a hardware register
access as required by the VT-d spec.
- Two patches for AMD IOMMU to force AMD GPUs into translation mode
when memory encryption is active and disallow using IOMMUv2
functionality. This makes the AMDGPU driver working when
memory encryption is active.
- Two more fixes for AMD IOMMU to fix updating the Interrupt
Remapping Table Entries.
- MAINTAINERS file update for the Qualcom IOMMU driver.
-----BEGIN PGP SIGNATURE-----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=2uqs
-----END PGP SIGNATURE-----
Merge tag 'iommu-fixes-v5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
- three Intel VT-d fixes to fix address handling on 32bit, fix a NULL
pointer dereference bug and serialize a hardware register access as
required by the VT-d spec.
- two patches for AMD IOMMU to force AMD GPUs into translation mode
when memory encryption is active and disallow using IOMMUv2
functionality. This makes the AMDGPU driver work when memory
encryption is active.
- two more fixes for AMD IOMMU to fix updating the Interrupt Remapping
Table Entries.
- MAINTAINERS file update for the Qualcom IOMMU driver.
* tag 'iommu-fixes-v5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/vt-d: Handle 36bit addressing for x86-32
iommu/amd: Do not use IOMMUv2 functionality when SME is active
iommu/amd: Do not force direct mapping when SME is active
iommu/amd: Use cmpxchg_double() when updating 128-bit IRTE
iommu/amd: Restore IRTE.RemapEn bit after programming IRTE
iommu/vt-d: Fix NULL pointer dereference in dev_iommu_priv_set()
iommu/vt-d: Serialize IOMMU GCMD register modifications
MAINTAINERS: Update QUALCOMM IOMMU after Arm SMMU drivers move
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCX1Rn1wAKCRCAXGG7T9hj
vlEjAQC/KGC3wYw5TweWcY48xVzgvued3JLAQ6pcDlOe6osd6AEAzZcZKgL948cx
oY0T98dxb/U+lUhbIzhpBr/30g8JbAQ=
=Xcxp
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.9-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from Juergen Gross:
"A small series for fixing a problem with Xen PVH guests when running
as backends (e.g. as dom0).
Mapping other guests' memory is now working via ZONE_DEVICE, thus not
requiring to abuse the memory hotplug functionality for that purpose"
* tag 'for-linus-5.9-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: add helpers to allocate unpopulated memory
memremap: rename MEMORY_DEVICE_DEVDAX to MEMORY_DEVICE_GENERIC
xen/balloon: add header guard
While looking for ->files in ->defer_list, consider that requests there
may actually be links.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
While trying to cancel requests with ->files, it also should look for
requests in ->defer_list, otherwise it might end up hanging a thread.
Cancel all requests in ->defer_list up to the last request there with
matching ->files, that's needed to follow drain ordering semantics.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
- Replace HTTP links with HTTPS ones (Alexander A. Klimov)
-----BEGIN PGP SIGNATURE-----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=w1IL
-----END PGP SIGNATURE-----
mergetag object 4e4bb89446
type commit
tag clang-format-for-linus-v5.9-rc4
tagger Miguel Ojeda <miguel.ojeda.sandonis@gmail.com> 1599306139 +0200
The usual trivial update:
- Update with the latest for_each macro list (Miguel Ojeda)
-----BEGIN PGP SIGNATURE-----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=Lcl0
-----END PGP SIGNATURE-----
mergetag object e5fc436f06
type commit
tag compiler-attributes-for-linus-v5.9-rc4
tagger Miguel Ojeda <miguel.ojeda.sandonis@gmail.com> 1599306822 +0200
Two trivial changes and a fix for sparse:
- sparse: use static inline for __chk_{user,io}_ptr() (Luc Van Oostenryck)
- Compiler Attributes: fix comment concerning GCC 4.6 (Luc Van Oostenryck)
- Compiler Attributes: remove comment about sparse not supporting __has_attribute (Luc Van Oostenryck)
-----BEGIN PGP SIGNATURE-----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=RrSY
-----END PGP SIGNATURE-----
Merge tags 'auxdisplay-for-linus-v5.9-rc4', 'clang-format-for-linus-v5.9-rc4' and 'compiler-attributes-for-linus-v5.9-rc4' of git://github.com/ojeda/linux
Pull misc fixes from Miguel Ojeda:
"A trivial patch for auxdisplay:
- Replace HTTP links with HTTPS ones (Alexander A. Klimov)
The usual clang-format trivial update:
- Update with the latest for_each macro list (Miguel Ojeda)
And Luc requested me to pick a sparse fix on my queue, so here it goes
along with other two trivial Compiler Attributes ones (also from Luc).
- sparse: use static inline for __chk_{user,io}_ptr() (Luc Van
Oostenryck)
- Compiler Attributes: fix comment concerning GCC 4.6 (Luc Van
Oostenryck)
- Compiler Attributes: remove comment about sparse not supporting
__has_attribute (Luc Van Oostenryck)"
* tag 'auxdisplay-for-linus-v5.9-rc4' of git://github.com/ojeda/linux:
auxdisplay: Replace HTTP links with HTTPS ones
* tag 'clang-format-for-linus-v5.9-rc4' of git://github.com/ojeda/linux:
clang-format: Update with the latest for_each macro list
* tag 'compiler-attributes-for-linus-v5.9-rc4' of git://github.com/ojeda/linux:
sparse: use static inline for __chk_{user,io}_ptr()
Compiler Attributes: fix comment concerning GCC 4.6
Compiler Attributes: remove comment about sparse not supporting __has_attribute
- HSDK-4xd Dev system: perf driver updates for sampling interrupt
- HSDK* Dev System : Ethernet broken [Evgeniy Didin]
- HIGHMEM broken (2 memory banks) [Mike Rapoport]
- show_regs() rewrite once and for all
- Other minor fixes
-----BEGIN PGP SIGNATURE-----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=vOZp
-----END PGP SIGNATURE-----
Merge tag 'arc-5.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
- HSDK-4xd Dev system: perf driver updates for sampling interrupt
- HSDK* Dev System: Ethernet broken [Evgeniy Didin]
- HIGHMEM broken (2 memory banks) [Mike Rapoport]
- show_regs() rewrite once and for all
- Other minor fixes
* tag 'arc-5.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: [plat-hsdk]: Switch ethernet phy-mode to rgmii-id
arc: fix memory initialization for systems with two memory banks
irqchip/eznps: Fix build error for !ARC700 builds
ARC: show_regs: fix r12 printing and simplify
ARC: HSDK: wireup perf irq
ARC: perf: don't bail setup if pct irq missing in device-tree
ARC: pgalloc.h: delete a duplicated word + other fixes
Merge misc fixes from Andrew Morton:
"19 patches.
Subsystems affected by this patch series: MAINTAINERS, ipc, fork,
checkpatch, lib, and mm (memcg, slub, pagemap, madvise, migration,
hugetlb)"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
include/linux/log2.h: add missing () around n in roundup_pow_of_two()
mm/khugepaged.c: fix khugepaged's request size in collapse_file
mm/hugetlb: fix a race between hugetlb sysctl handlers
mm/hugetlb: try preferred node first when alloc gigantic page from cma
mm/migrate: preserve soft dirty in remove_migration_pte()
mm/migrate: remove unnecessary is_zone_device_page() check
mm/rmap: fixup copying of soft dirty and uffd ptes
mm/migrate: fixup setting UFFD_WP flag
mm: madvise: fix vma user-after-free
checkpatch: fix the usage of capture group ( ... )
fork: adjust sysctl_max_threads definition to match prototype
ipc: adjust proc_ipc_sem_dointvec definition to match prototype
mm: track page table modifications in __apply_to_page_range()
MAINTAINERS: IA64: mark Status as Odd Fixes only
MAINTAINERS: add LLVM maintainers
MAINTAINERS: update Cavium/Marvell entries
mm: slub: fix conversion of freelist_corrupted()
mm: memcg: fix memcg reclaim soft lockup
memcg: fix use-after-free in uncharge_batch
Otherwise gcc generates warnings if the expression is complicated.
Fixes: 312a0c1709 ("[PATCH] LOG2: Alter roundup_pow_of_two() so that it can use a ilog2() on a constant")
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Link: https://lkml.kernel.org/r/0-v1-8a2697e3c003+41165-log_brackets_jgg@nvidia.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
collapse_file() in khugepaged passes PAGE_SIZE as the number of pages to
be read to page_cache_sync_readahead(). The intent was probably to read
a single page. Fix it to use the number of pages to the end of the
window instead.
Fixes: 99cb0dbd47 ("mm,thp: add read-only THP support for (non-shmem) FS")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Acked-by: Song Liu <songliubraving@fb.com>
Acked-by: Yang Shi <shy828301@gmail.com>
Acked-by: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Cc: Eric Biggers <ebiggers@google.com>
Link: https://lkml.kernel.org/r/20200903140844.14194-2-willy@infradead.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is a race between the assignment of `table->data` and write value
to the pointer of `table->data` in the __do_proc_doulongvec_minmax() on
the other thread.
CPU0: CPU1:
proc_sys_write
hugetlb_sysctl_handler proc_sys_call_handler
hugetlb_sysctl_handler_common hugetlb_sysctl_handler
table->data = &tmp; hugetlb_sysctl_handler_common
table->data = &tmp;
proc_doulongvec_minmax
do_proc_doulongvec_minmax sysctl_head_finish
__do_proc_doulongvec_minmax unuse_table
i = table->data;
*i = val; // corrupt CPU1's stack
Fix this by duplicating the `table`, and only update the duplicate of
it. And introduce a helper of proc_hugetlb_doulongvec_minmax() to
simplify the code.
The following oops was seen:
BUG: kernel NULL pointer dereference, address: 0000000000000000
#PF: supervisor instruction fetch in kernel mode
#PF: error_code(0x0010) - not-present page
Code: Bad RIP value.
...
Call Trace:
? set_max_huge_pages+0x3da/0x4f0
? alloc_pool_huge_page+0x150/0x150
? proc_doulongvec_minmax+0x46/0x60
? hugetlb_sysctl_handler_common+0x1c7/0x200
? nr_hugepages_store+0x20/0x20
? copy_fd_bitmaps+0x170/0x170
? hugetlb_sysctl_handler+0x1e/0x20
? proc_sys_call_handler+0x2f1/0x300
? unregister_sysctl_table+0xb0/0xb0
? __fd_install+0x78/0x100
? proc_sys_write+0x14/0x20
? __vfs_write+0x4d/0x90
? vfs_write+0xef/0x240
? ksys_write+0xc0/0x160
? __ia32_sys_read+0x50/0x50
? __close_fd+0x129/0x150
? __x64_sys_write+0x43/0x50
? do_syscall_64+0x6c/0x200
? entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes: e5ff215941 ("hugetlb: multiple hstates for multiple page sizes")
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Andi Kleen <ak@linux.intel.com>
Link: http://lkml.kernel.org/r/20200828031146.43035-1-songmuchun@bytedance.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since commit cf11e85fc0 ("mm: hugetlb: optionally allocate gigantic
hugepages using cma"), the gigantic page would be allocated from node
which is not the preferred node, although there are pages available from
that node. The reason is that the nid parameter has been ignored in
alloc_gigantic_page().
Besides, the __GFP_THISNODE also need be checked if user required to
alloc only from the preferred node.
After this patch, the preferred node is tried first before other allowed
nodes, and don't try to allocate from other nodes if __GFP_THISNODE is
specified. If user don't specify the preferred node, the current node
will be used as preferred node, which makes sure consistent behavior of
allocating gigantic and non-gigantic hugetlb page.
Fixes: cf11e85fc0 ("mm: hugetlb: optionally allocate gigantic hugepages using cma")
Signed-off-by: Li Xinhai <lixinhai.lxh@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Roman Gushchin <guro@fb.com>
Link: https://lkml.kernel.org/r/20200902025016.697260-1-lixinhai.lxh@gmail.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eddie James