This isn't all that relevant for RX right now, but TX can be concurrent
due to multi-queue and the accounting is therefore broken.
Use the standard per-CPU statistics to avoid this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This support is essentially useless as typically networks are encrypted,
frames will be filtered by hardware, and rate scaling will be done with
the intended recipient in mind. For real monitoring of the network, the
monitor mode support should be used instead.
Removing it removes a lot of corner cases.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Stations assigned to an AP_VLAN type interface are flushed
when the interface is stopped, but then we warn about it.
Suppress the warning since there's nothing else that would
ensure those stations are already removed at this point.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows drivers to request per-vif and per-sta-tid queues from which
they can pull frames. This makes it easier to keep the hardware queues
short, and to improve fairness between clients and vifs.
The task of scheduling packet transmission is left up to the driver -
queueing is controlled by mac80211. Drivers can only dequeue packets by
calling ieee80211_tx_dequeue. This makes it possible to add active queue
management later without changing drivers using this code.
This can also be used as a starting point to implement A-MSDU
aggregation in a way that does not add artificially induced latency.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[resolved minor context conflict, minor changes, endian annotations]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This will expose in /sys whether the ifname of a device is set by
userspace or generated by the kernel. The latter kind (wlanX, etc)
is not deterministic, so userspace needs to rename these devices
to names that are guaranteed to stay the same between reboots. The
former, however should never be renamed, so userspace needs to be
able to reliably tell the difference.
Similar functionality was introduced for the rtnetlink core in
commit 5517750f05 ("net: rtnetlink - make create_link take name_assign_type")
Signed-off-by: Tom Gundersen <teg@jklm.no>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Brett Rudley <brudley@broadcom.com>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Cc: Hante Meuleman <meuleman@broadcom.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
[reformat changelog to fit 72 cols]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This mechanism was historic, and only ever used by IBSS, which
also doesn't need to have it as it properly manages station's
802.1X PAE state (or, with WEP, always has a key.)
Remove the mechanism to clean up the code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we go to suspend, there is complex set of states that
avoids races. The quiescing variable is set whlie
__ieee80211_suspend is running. Then suspended is set.
The code makes sure there is no window without any of these
flags.
The problem is that workers can still be enqueued while we
are quiescing. This leads to situations where the driver is
already suspending and other flows like disassociation are
handled by a worker.
To fix this, we need to check quiescing and suspended flags
in the worker itself and not only before enqueueing it.
I also add here extensive documentation to ease the
understanding of these complex issues.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Control per packet Transmit Power Control (TPC) in lower drivers
according to TX power settings configured by the user. In particular TPC is
enabled if value passed in enum nl80211_tx_power_setting is
NL80211_TX_POWER_LIMITED (allow using less than specified from userspace),
whereas TPC is disabled if nl80211_tx_power_setting is set to
NL80211_TX_POWER_FIXED (use value configured from userspace)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When roaming / suspending, it makes no sense to wait until
the transmit queues of the device are empty. In extreme
condition they can be starved (VO saturating the air), but
even in regular cases, it is pointless to delay the roaming
because the low level driver is trying to send packets to
an AP which is far away. We'd rather drop these packets and
let TCP retransmit if needed. This will allow to speed up
the roaming.
For suspend, the explanation is even more trivial.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg <johannes@sipsolutions.net> says:
"This time I have Felix's no-status rate control work, which will allow
drivers to work better with rate control even if they don't have perfect
status reporting. In addition to this, a small hwsim fix from Patrik,
one of the regulatory patches from Arik, and a number of cleanups and
fixes I did myself.
Of note is a patch where I disable CFG80211_WEXT so that compatibility
is no longer selectable - this is intended as a wake-up call for anyone
who's still using it, and is still easily worked around (it's a one-line
patch) before we fully remove the code as well in the future."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of keeping track of all those special cases where
VLAN interfaces have no bss_conf.chandef, just make sure
they have the same as the AP interface they belong to.
Among others, this fixes a crash getting a VLAN's channel
from userspace since a NULL channel is returned as a good
result (return value 0) for VLANs since the commit below.
Cc: stable@vger.kernel.org [3.18 only]
Fixes: c12bc4885f ("mac80211: return the vif's chandef in ieee80211_cfg_get_channel()")
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[rewrite commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
another relatively large set of changes:
* TDLS off-channel support set from Arik/Liad, with some support
patches I did
* custom regulatory fixes from Arik
* minstrel VHT fix (and a small optimisation) from Felix
* add back radiotap vendor namespace support (myself)
* random MAC address scanning for cfg80211/mac80211/hwsim (myself)
* CSA improvements (Luca)
* WoWLAN Net Detect (wake on network found) support (Luca)
* and lots of other smaller changes from many people
-----BEGIN PGP SIGNATURE-----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=q4e6
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-john-2014-11-20' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg <johannes@sipsolutions.net> says:
"It has been a while since my last pull request, so we accumulated
another relatively large set of changes:
* TDLS off-channel support set from Arik/Liad, with some support
patches I did
* custom regulatory fixes from Arik
* minstrel VHT fix (and a small optimisation) from Felix
* add back radiotap vendor namespace support (myself)
* random MAC address scanning for cfg80211/mac80211/hwsim (myself)
* CSA improvements (Luca)
* WoWLAN Net Detect (wake on network found) support (Luca)
* and lots of other smaller changes from many people"
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When receiving a TDLS channel switch request or response, parse the frame
and call a new tdls_recv_channel_switch op in the low level driver with
the parsed data.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds 802.11p OCB (Outside the Context of a BSS) mode
support.
When communicating in OCB mode a mandatory wildcard BSSID
(48 '1' bits) is used.
The EDCA parameters handling function was changed to support
802.11p specific values.
The insertion of a newly discovered STAs is done in the similar way
as in the IBSS mode -- through the deferred insertion.
The OCB mode uses a periodic 'housekeeping task' for expiration of
disconnected STAs (in the similar manner as in the MESH mode).
New Kconfig option for verbose OCB debugging outputs is added.
Signed-off-by: Rostislav Lisovy <rostislav.lisovy@fel.cvut.cz>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds new iface type (NL80211_IFTYPE_OCB) representing
the OCB (Outside the Context of a BSS) mode.
When establishing a connection to the network a cfg80211_join_ocb
function is called (particular nl80211_command is added as well).
A mandatory parameters during the ocb_join operation are 'center
frequency' and 'channel width (5/10 MHz)'.
Changes done in mac80211 are minimal possible required to avoid
many warnings (warning: enumeration value 'NL80211_IFTYPE_OCB'
not handled in switch) during compilation. Full functionality
(where needed) is added in the following patch.
Signed-off-by: Rostislav Lisovy <rostislav.lisovy@fel.cvut.cz>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When an interface is deleted, an ongoing hardware scan is canceled and
the driver must abort the scan, at the very least reporting completion
while the interface is removed.
However, if it scheduled the work that might only run after everything
is said and done, which leads to cfg80211 warning that the scan isn't
reported as finished yet; this is no fault of the driver, it already
did, but mac80211 hasn't processed it.
To fix this situation, flush the delayed work when the interface being
removed is the one that was executing the scan.
Cc: stable@vger.kernel.org
Reported-by: Sujith Manoharan <sujith@msujith.org>
Tested-by: Sujith Manoharan <sujith@msujith.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Userspace can add keys to an AP mode interface before start_ap has been
called. If there have been no calls to start_ap/stop_ap in the mean
time, the keys will still be around when the interface is brought down.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[adjust comments, fix AP_VLAN case]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is useful when creating virtual interfaces.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of immediately reopening the queues (in case of block_tx),
calling the post_channel_switch operation and sending the
notification, wait for the first beacon on the new channel. This
makes sure that we don't lose packets if the AP/GO is not on the new
channel yet.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Our legal structure changed at some point (see wikipedia), but
we forgot to immediately switch over to the new copyright
notice.
For files that we have modified in the time since the change,
add the proper copyright notice now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When starting an offloaded BA session it is
unknown what starting sequence number should be
used. Using last_seq worked in most cases except
after hw restart.
When hw restart is requested last_seq is
(rightfully so) kept unmodified. This ended up
with BA sessions being restarted with an aribtrary
BA window values resulting in dropped frames until
sequence numbers caught up.
Instead of last_seq pick seqno of a first Rxed
frame of a given BA session.
This fixes stalled traffic after hw restart with
offloaded BA sessions (currently only ath10k).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
John W. Linville says:
====================
pull request: wireless-next 2014-07-25
Please pull this batch of updates intended for the 3.17 stream!
For the mac80211 bits, Johannes says:
"We have a lot of TDLS patches, among them a fix that should make hwsim
tests happy again. The rest, this time, is mostly small fixes."
For the Bluetooth bits, Gustavo says:
"Some more patches for 3.17. The most important change here is the move of
the 6lowpan code to net/6lowpan. It has been agreed with Davem that this
change will go through the bluetooth tree. The rest are mostly clean up and
fixes."
and,
"Here follows some more patches for 3.17. These are mostly fixes to what
we've sent to you before for next merge window."
For the iwlwifi bits, Emmanuel says:
"I have the usual amount of BT Coex stuff. Arik continues to work
on TDLS and Ariej contributes a few things for HS2.0. I added a few
more things to the firmware debugging infrastructure. Eran fixes a
small bug - pretty normal content."
And for the Atheros bits, Kalle says:
"For ath6kl me and Jessica added support for ar6004 hw3.0, our latest
version of ar6004.
For ath10k Janusz added a printout so that it's easier to check what
ath10k kconfig options are enabled. He also added a debugfs file to
configure maximum amsdu and ampdu values. Also we had few fixes as
usual."
On top of that is the usual large batch of various driver updates --
brcmfmac, mwifiex, the TI drivers, and wil6210 all get some action.
Rafał has also been very busy with b43 and related updates.
Also, I pulled the wireless tree into this in order to resolve a
merge conflict...
P.S. The change to fs/compat_ioctl.c reflects a name change in a
Bluetooth header file...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers may be performing most of Tx/Rx
aggregation on their own (e.g. in firmware)
including AddBa/DelBa negotiations but may
otherwise require Rx reordering assistance.
The patch exports 2 new functions for establishing
Rx aggregation sessions in assumption device
driver has taken care of the necessary
negotiations.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
[fix endian bug]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We can only be a station for TDLS connections. Also fix a bug where
a delayed work could be left scheduled if the station interface was
brought down during TDLS setup.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When setting up a TDLS session, register a delayed work to remove
the peer if setup times out. Prevent concurrent setups to support this
capacity.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of stopping all the hardware queues during channel switch,
which is especially bad when we have large CSA counts, stop only the
queues that are assigned to the vif that is performing the channel
switch.
Additionally, check for (sdata->csa_block_tx) instead of calling
ieee80211_csa_needs_block_tx(), which can now be removed.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sometimes different vifs may be stopping the queues for the same
reason (e.g. when several interfaces are performing a channel switch).
Instead of using a bitmask for the reasons, use an integer that holds
a refcount instead. In order to keep it backwards compatible,
introduce a boolean in some functions that tell us whether the queue
stopping should be refcounted or not. For now, use not refcounted for
all calls to keep it functionally the same as before.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, cfg80211 tries to implement ethtool, but that doesn't
really scale well, with all the different operations. Make the
lower-level driver responsible for it, which currently only has
an effect on mac80211. It will similarly not scale well at that
level though, since mac80211 also has many drivers.
To cleanly implement this in mac80211, introduce a new file and
move some code to appropriate places.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
net/core/rtnetlink.c
net/core/skbuff.c
Both conflicts were very simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
unregister_netdevice_many() API is error prone and we had too
many bugs because of dangling LIST_HEAD on stacks.
See commit f87e6f4793 ("net: dont leave active on stack LIST_HEAD")
In fact, instead of making sure no caller leaves an active list_head,
just force a list_del() in the callee. No one seems to need to access
the list after unregister_netdevice_many()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark new interfaces as idle to allow operations that require that
interfaces are idle to take place. Interface types that are always
not idle (like AP interfaces) will be set as not idle when they are
assigned a channel context.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Emmanuel Grumbach<emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since the commit below, cfg80211_chandef_dfs_required()
will warn if it gets a an NL80211_IFTYPE_UNSPECIFIED iftype
as explicitely written in the commit log.
When an virtual monitor interface is added, its type is set
in ieee80211_sub_if_data.vif.type, but not in
ieee80211_sub_if_data.wdev.iftype which is passed to
cfg80211_chandef_dfs_required() hence resulting in the
following warning:
WARNING: CPU: 1 PID: 21265 at net/wireless/chan.c:376 cfg80211_chandef_dfs_required+0xbc/0x130 [cfg80211]()
Modules linked in: [...]
CPU: 1 PID: 21265 Comm: ifconfig Tainted: G W O 3.13.11+ #12
Hardware name: Dell Inc. Latitude E6410/0667CC, BIOS A01 03/05/2010
0000000000000009 ffff88008f5fdb08 ffffffff817d4219 ffff88008f5fdb50
ffff88008f5fdb40 ffffffff8106f57d 0000000000000000 0000000000000000
ffff880081062fb8 ffff8800810604e0 0000000000000001 ffff88008f5fdba0
Call Trace:
[<ffffffff817d4219>] dump_stack+0x4d/0x66
[<ffffffff8106f57d>] warn_slowpath_common+0x7d/0xa0
[<ffffffff8106f5ec>] warn_slowpath_fmt+0x4c/0x50
[<ffffffffa04ea4ec>] cfg80211_chandef_dfs_required+0xbc/0x130 [cfg80211]
[<ffffffffa06b1024>] ieee80211_vif_use_channel+0x94/0x500 [mac80211]
[<ffffffffa0684e6b>] ieee80211_add_virtual_monitor+0x1ab/0x5c0 [mac80211]
[<ffffffffa0686ae5>] ieee80211_do_open+0xe75/0x1580 [mac80211]
[<ffffffffa0687259>] ieee80211_open+0x69/0x70 [mac80211]
[snip]
Fixes: 00ec75fc5a ("cfg80211: pass the actual iftype when calling cfg80211_chandef_dfs_required()")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Acked-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It was possible for tx queues to be stuck stopped
if AP CSA finalization failed. In that case
neither stop_ap nor do_stop woke the queues up.
This means it was impossible to perform tx at all
until driver was reloaded or a successful CSA was
performed later.
It was possible to solve this in a simpler manner
however this is more robust and future proof
(having multi-vif CSA in mind).
New sdata->csa_block_tx is introduced to keep
track of which interfaces requested tx to be
blocked for CSA. This is required because mac80211
stops all tx queues for that purpose. This means
queues must be awoken only when last tx-blocking
CSA interface is finished.
It is still possible to have tx queues stopped
after CSA failure but as soon as offending
interfaces are stopped from userspace (stop_ap or
ifdown) tx queues are woken up properly.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Return NOTIFY_DONE if we don't care this time's notification, return
NOTIFY_OK if we successfully handled this time's notification. That's
the formal way to do it.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This can be useful. Provides a more straghtforward
way to iterate over interfaces taking part in
chanctx reservation and allows tracking chanctx
usage explicitly.
The structure is protected by local->chanctx_mtx.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This can be useful. Provides a more straghtforward
way to iterate over interfaces bound to a given
chanctx and allows tracking chanctx usage
explicitly.
The structure is protected by local->chanctx_mtx.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It was impossible to change chanctx of master AP
for AP VLANs because the copy function requires
RTNL which can't be simply taken in mac80211 code
due to possible deadlocks.
This is required for future chanctx reservation
that re-bind vifs to new chanctx. This requires
safe AP VLAN iteration without RTNL.
Now VLANs can be iterated while holding either
RTNL or local->mtx because the list is modified
while holding both of these locks.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Get rid of the cfg80211_can_add_interface() and
cfg80211_can_change_interface() functions by moving that functionality
to mac80211. With this patch all interface combination checks are now
out of cfg80211 (except for the channel switch case which will be
addressed in a future commit).
Additionally, modify the ieee80211_check_combinations() function so
that an undefined chandef can be passed, in order to use it before a
channel is defined.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
rcu_assign_pointer() ensures that the initialization of a structure is
carried out before storing a pointer to that structure. However, in the
case that NULL is assigned there's no structure to initialize so using
RCU_INIT_POINTER instead is safe and more efficient.
Signed-off-by: Monam Agarwal <monamagarwal123@gmail.com>
[squash eight tiny patches, rewrite commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a new argument for ndo_select_queue() callback that passes a
fallback handler. This gets invoked through netdev_pick_tx();
fallback handler is currently __netdev_pick_tx() as most drivers
invoke this function within their customized implementation in
case for skbs that don't need any special handling. This fallback
handler can then be replaced on other call-sites with different
queue selection methods (e.g. in packet sockets, pktgen etc).
This also has the nice side-effect that __netdev_pick_tx() is
then only invoked from netdev_pick_tx() and export of that
function to modules can be undone.
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no need to start iterating the list only to break on the
first item, just use !list_empty() and also simplify the whole
conditional into a single expression.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During channel context assignment, the interface should
be found by interface iteration, so we need to assign the
pointer before the channel context.
Reported-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Tested-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The patch adds a missing sdata lock and adds a few
lockdeps for easier maintenance.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, the tx queue were selected implicitly in ndo_dfwd_start_xmit(). The
will cause several issues:
- NETIF_F_LLTX were removed for macvlan, so txq lock were done for macvlan
instead of lower device which misses the necessary txq synchronization for
lower device such as txq stopping or frozen required by dev watchdog or
control path.
- dev_hard_start_xmit() was called with NULL txq which bypasses the net device
watchdog.
- dev_hard_start_xmit() does not check txq everywhere which will lead a crash
when tso is disabled for lower device.
Fix this by explicitly introducing a new param for .ndo_select_queue() for just
selecting queues in the case of l2 forwarding offload. netdev_pick_tx() was also
extended to accept this parameter and dev_queue_xmit_accel() was used to do l2
forwarding transmission.
With this fixes, NETIF_F_LLTX could be preserved for macvlan and there's no need
to check txq against NULL in dev_hard_start_xmit(). Also there's no need to keep
a dedicated ndo_dfwd_start_xmit() and we can just reuse the code of
dev_queue_xmit() to do the transmission.
In the future, it was also required for macvtap l2 forwarding support since it
provides a necessary synchronization method.
Cc: John Fastabend <john.r.fastabend@intel.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: e1000-devel@lists.sourceforge.net
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the possibly more efficient ether_addr_equal
to instead of memcmp.
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: David Miller <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The scan code creates an iflist_mtx -> mtx locking dependency,
and a few other places, notably radar detection, were creating
the opposite dependency, causing lockdep to complain. As scan
and radar detection are mutually exclusive, the deadlock can't
really happen in practice, but it's still bad form.
A similar issue exists in the monitor mode code, but this is
only used by channel-context drivers right now and those have
to have hardware scan, so that also can't happen.
Still, fix these issues by making some of the channel context
code require the mtx to be held rather than acquiring it, thus
allowing the monitor/radar callers to keep the iflist_mtx->mtx
lock ordering.
While at it, also fix access to the local->scanning variable
in the radar code, and document that radar_detect_enabled is
now properly protected by the mtx.
All this would now introduce an ABBA deadlock between the DFS
work cancelling and local->mtx, so change the locking there a
bit to not need to use cancel_delayed_work_sync() but be able
to just use cancel_delayed_work(). The work is also safely
stopped/removed when the interface is stopped, so no extra
changes are needed.
Reported-by: Kalle Valo <kvalo@qca.qualcomm.com>
Tested-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The radar detection code changed a few times, and due to
the changes some iflist_mtx locking stayed in that isn't
actually necessary - remove it.
One version of the code needed it because an AP interface's
VLAN list was changed to use this, but then we moved the
list handling outside of the chanctx handling and thus the
locking was no longer needed.
Tested-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the AP interface is stopped, free all AP and VLAN keys at
once to only require synchronize_net() once. Since that does
synchronize_net(), also move two such calls into the function
(using the new force_synchronize parameter) to avoid doing it
twice.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we can assume that stations are never referenced by the
driver after sta_state returns (and this is true since the
previous iwlmvm patch and for all other drivers) then we
don't need to delay station destruction, and don't need to
play tricks with rcu_barrier() etc.
This should speed up some scenarios like hostapd shutdown.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit 488b366a45.
The code isn't used by anyone, and the Intel driver isn't planning
to use it either right now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
All interface types now properly clean up their stations
using some form of sta_info_flush() themselves, so there's
no need to try it again at teardown. Remove the call to
get rid of the extra delay from the synchronize_net() and
rcu_barrier() calls.
Reported-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds generic cipher scheme support to mac80211, such schemes
are fully under control by the driver. On hw registration drivers
may specify additional HW ciphers with a scheme how these ciphers
have to be handled by mac80211 TX/RR. A cipher scheme specifies a
cipher suite value, a size of the security header to be added to
or stripped from frames and how the PN is to be verified on RX.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To report channel width correctly we have
to send correct channel parameters from
mac80211 when calling cfg80211_cac_event().
This is required in case of using channel width
higher than 20MHz and we have to set correct
dfs channel state after CAC (NL80211_DFS_AVAILABLE).
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Reviewed-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit "mac80211: implement SMPS for AP" applies to AP_VLAN as well.
It assumes that sta->sdata->vif.bss_conf.bssid is present, which did not
get set for AP_VLAN.
Initialize it to sdata->vif.addr like for other interface types.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the driver requests to move to STATIC or DYNAMIC SMPS,
we send an action frame to each associated station and
reconfigure the channel context / driver.
Of course, non-MIMO stations are ignored.
The beacon isn't updated. The association response will
include the original capabilities. Stations that associate
while in non-OFF SMPS mode will get an action frame right
after association to inform them about our current state.
Note that we wait until the end of the EAPOL. Sending an
action frame before the EAPOL is finished can be an issue
for a few clients. Clients aren't likely to send EAPOL
frames in MIMO anyway.
When the SMPS configuration gets more permissive (e.g.
STATIC -> OFF), we don't wake up stations that are asleep
We remember that they don't know about the change and send
the action frame when they wake up.
When the SMPS configuration gets more restrictive (e.g.
OFF -> STATIC), we set the TIM bit for every sleeping STA.
uAPSD stations might send MIMO until they poll the action
frame, but this is for a short period of time.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[fix vht streams loop, initialisation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This function adds the channel switch announcement implementation for the
IBSS code. It is triggered by userspace (mac80211/cfg) or by external
channel switch announcement, which have to be adopted. Both CSAs in
beacons and action frames are supported. As for AP mode, the channel
switch is applied after some time. However in IBSS mode, the channel
switch IEs are generated in the kernel.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Jouni reported that with mac80211_hwsim, multicast TX was causing
crashes due to invalid vif->cab_queue assignment. It turns out that
this is caused by change_interface() getting invoked and not having
the vif->type/vif->p2p assigned correctly before calling the queue
check (ieee80211_check_queues). Fix this by passing the 'external'
interface type to the function and adjusting it accordingly.
While at it, also fix the error path in change_interface, it wasn't
correctly resetting to the external type but using the internal one
instead.
Fortunately this affects on hwsim because all other drivers set the
vif->type/vif->p2p variables when changing iftype. This shouldn't
be needed, but almost all implementations actually do it for their
own internal handling.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The count field in CSA must be decremented with each beacon
transmitted. This patch implements the functionality for drivers
using ieee80211_beacon_get(). Other drivers must call back manually
after reaching count == 0.
This patch also contains the handling and finish worker for the channel
switch command, and mac80211/chanctx code to allow to change a channel
definition of an active channel context.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
[small cleanups, catch identical chandef]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some regulations (like germany, but also FCC) express their transmission
power limit in dBm/MHz or mW/MHz. To cope with that and be on the safe
side, reduce the maximum power to half (10 MHz) or quarter (5 MHz)
when operating on these reduced bandwidth channels.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Merge 'net' bug fixes into 'net-next' as we have patches
that will build on top of them.
This merge commit includes a change from Emil Goode
(emilgoode@gmail.com) that fixes a warning that would
have been introduced by this merge. Specifically it
fixes the pingv6_ops method ipv6_chk_addr() to add a
"const" to the "struct net_device *dev" argument and
likewise update the dummy_ipv6_chk_addr() declaration.
Signed-off-by: David S. Miller <davem@davemloft.net>
Support them only if the driver advertises support for them via
IEEE80211_HW_SUPPORTS_ACTIVE_MONITOR. Unlike normal monitor interfaces,
they are added to the driver, along with their MAC address.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
So far, only net_device * could be passed along with netdevice notifier
event. This patch provides a possibility to pass custom structure
able to provide info that event listener needs to know.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
v2->v3: fix typo on simeth
shortened dev_getter
shortened notifier_info struct name
v1->v2: fix notifier_call parameter in call_netdevice_notifier()
Signed-off-by: David S. Miller <davem@davemloft.net>
When changing the MAC address of a single vif mac80211 will check if
the new address fits into the address mask specified by the driver.
This only needs to be done when using multiple BSSIDs. Hence, check
the new address only against all other vifs.
Also fix the MAC address assignment on new interfaces if the user
changed the address of a vif such that perm_addr is not covered by
addr_mask anymore.
Resolves:
https://bugzilla.kernel.org/show_bug.cgi?id=57371
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Reported-by: Alessandro Lannocca <alessandro.lannocca@gmail.com>
Cc: Alessandro Lannocca <alessandro.lannocca@gmail.com>
Cc: Bruno Randolf <br1@thinktube.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since Eric's commit efe117ab8 ("Speedup ieee80211_remove_interfaces")
there's a bug in mac80211 when it unregisters with AP_VLAN interfaces
up. If the AP_VLAN interface was registered after the AP it belongs
to (which is the typical case) and then we get into this code path,
unregister_netdevice_many() will crash because it isn't prepared to
deal with interfaces being closed in the middle of it. Exactly this
happens though, because we iterate the list, find the AP master this
AP_VLAN belongs to and dev_close() the dependent VLANs. After this,
unregister_netdevice_many() won't pick up the fact that the AP_VLAN
is already down and will do it again, causing a crash.
Cc: stable@vger.kernel.org [2.6.33+]
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A lot of code in mac80211 assumes that the hw queues are
set up correctly for all interfaces (except for monitor)
but this isn't true for AP_VLAN interfaces. Fix this by
copying the AP master configuration when an AP VLAN is
brought up, after this the AP interface can't change its
configuration any more and needs to be brought down to
change it, which also forces AP_VLAN interfaces down, so
just copying in open() is sufficient.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since Eric's commit efe117ab8 ("Speedup ieee80211_remove_interfaces")
there's a bug in mac80211 when it unregisters with AP_VLAN interfaces
up. If the AP_VLAN interface was registered after the AP it belongs
to (which is the typical case) and then we get into this code path,
unregister_netdevice_many() will crash because it isn't prepared to
deal with interfaces being closed in the middle of it. Exactly this
happens though, because we iterate the list, find the AP master this
AP_VLAN belongs to and dev_close() the dependent VLANs. After this,
unregister_netdevice_many() won't pick up the fact that the AP_VLAN
is already down and will do it again, causing a crash.
Cc: stable@vger.kernel.org [2.6.33+]
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A lot of code in mac80211 assumes that the hw queues are
set up correctly for all interfaces (except for monitor)
but this isn't true for AP_VLAN interfaces. Fix this by
copying the AP master configuration when an AP VLAN is
brought up, after this the AP interface can't change its
configuration any more and needs to be brought down to
change it, which also forces AP_VLAN interfaces down, so
just copying in open() is sufficient.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The code I added in "mac80211: don't start new netdev queues
if driver stopped" crashes for monitor and AP VLAN interfaces
because while they have a netdev, they don't have queues set
up by the driver.
To fix the crash, exclude these from queue accounting here
and just start their netdev queues unconditionally.
For monitor, this is the best we can do, as we can redirect
frames there to any other interface and don't know which one
that will since it can be different for each frame.
For AP VLAN interfaces, we can do better later and actually
properly track the queue status. Not doing this is really a
separate bug though.
Reported-by: Ilan Peer <ilan.peer@intel.com>
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The RCU docs used to state that rcu_barrier() included a wait
for an RCU grace period; however the comments for rcu_barrier()
as of commit f0a0e6f... "rcu: Clarify memory-ordering properties
of grace-period primitives" contradict this.
So add back synchronize_{rcu,net}() to where they once were,
but keep the rcu_barrier()s for the call_rcu() callbacks.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bob Copeland <bob@cozybit.com>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
feng xiangjun reports that my
commit 382a103b2b
Author: Johannes Berg <johannes.berg@intel.com>
Date: Fri Mar 22 22:30:09 2013 +0100
mac80211: fix idle handling sequence
broke the wireless status LED. The reason is that
we now call ieee80211_idle_off() when the channel
context is assigned, and that doesn't recalculate
the LED state. Fix this by making that function a
wrapper around most of idle recalculation while
forcing active.
Reported-by: feng xiangjun <fengxj325@gmail.com>
Tested-by: feng xiangjun <fengxj325@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a new netdev (e.g. an AP VLAN) is created while the driver
has queues stopped, the new netdev queues will be started even
though they shouldn't. This will lead to frames accumulating
on the internal mac80211 pending queues instead of properly
being held on the netdev queues.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Given the (nested) switch statements, this code can't
be reached, so make it warn instead of manipulating
the carrier state which seems purposeful.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a device is unplugged while suspended, mac80211 is
de-initialized and all interfaces are removed while no
state is actually present in the driver. This can cause
warnings and driver confusion.
Fix this by reordering the do_stop code to not call the
driver when it is suspended, i.e. when there's no state
in the driver anyway.
The previous patches removed a few corner cases in ROC
and virtual monitor interfaces so that now this is safe
to do and no state should be left over.
Reported-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It has to be removed from the driver, but completely
destroying it helps handle unplug of a device during
suspend since then the channel context handling etc.
doesn't have to happen later when it's removed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
They can't really be executed while suspended and could
trigger work warnings, so abort all ROC items. When the
system resumes the notifications about this will be
delivered to userspace which can then act accordingly
(though it will assume they were canceled/finished.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The code now explicitly calls ieee80211_configure_filter()
anyway, so nothing needs to be explained.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The master interface no longer exists ... and hasn't for
a few years now, so remove this reference :-)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Corey Richardson reported that my idle handling cleanup
(commit fd0f979a1b, "mac80211: simplify idle handling")
broke ath9k_htc. The reason appears to be that it wants
to go out of idle before switching channels. To fix it,
reimplement that sequence.
Reported-by: Corey Richardson <corey@octayn.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The virtual monitor interface has a locking issue, it calls
into the channel context code with the iflist mutex held
which isn't allowed since it is usually acquired the other
way around. The mutex is still required for the interface
iteration, but need not be held across the channel calls.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a number of situations in which mac80211 only
really needs to flush queues for one virtual interface,
and in fact during this frames might be transmitted on
other virtual interfaces. Calculate and pass a queue
bitmap to the driver so it knows which queues to flush.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This basically reverts commit b207cdb07f.
Now is possible to use drv_{add,remove}_interface() and vif->debugfs_dir
to create/remove per interface debugfs files. Remove redundant
callbacks.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some devices have multicast filter capability for each individual
virtual interface rather than just a global one. Add an interface
specific driver callback allowing such drivers to configure this.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For AP interfaces, there's no need to flush stations
or keys again when the interface is stopped as already
happened when the BSS was stopped on the interface.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since hostapd will remove keys this isn't usually
an issue, but we shouldn't leak keys to the next
BSS started on the same interface. For VLANs this
also fixes a bug, keys that aren't removed would
otherwise be leaked.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During roaming, the crypto_tx_tailroom_needed_cnt counter
will often take values 2,1,0,1,2 because first keys are
removed and then new keys are added. This is inefficient
because during the 0->1 transition, synchronize_net must
be called to avoid packet races, although typically no
packets would be flowing during that time.
To avoid that, defer the decrement (2->1, 1->0) when keys
are removed (by half a second). This means the counter
will really have the values 2,2,2,3,4 ... 2, thus never
reaching 0 and having to do the 0->1 transition.
Note that this patch entirely disregards the drivers for
which this optimisation was done to start with, for them
the key removal itself will be expensive because it has
to synchronize_net() after the counter is incremented to
remove the key from HW crypto. For them the sequence will
look like this: 0,1,0,1,0,1,0,1,0 (*) which is clearly a
lot more inefficient. This could be addressed separately,
during key removal the 0->1->0 sequence isn't necessary.
(*) it starts at 0 because HW crypto is on, then goes to
1 when HW crypto is disabled for a key, then back to
0 because the key is deleted; this happens for both
keys in the example. When new keys are added, it goes
to 1 first because they're added in software; when a
key is moved to hardware it goes back to 0
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since two years no mac80211 driver implement support for NAPI. Looks
this feature is unneeded, so remove it from generic mac80211 code.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When setting a monitor interface up or down, the idle state needs to be
recalculated, otherwise the hardware will just stay in its previous idle
state.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the driver does not want a monitor mode VIF, no channel context is
allocated for it. This causes ieee80211_recalc_idle to put the hardware
into idle mode if only a monitor mode is active, breaking injection.
Fix this by checking local->monitors in addition to active channel
contexts.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If an interface is set down while authenticating or
associating, there's a station entry that will be
removed by the flushing in do_stop() and that will
cause a warning. It's otherwise harmless, but avoid
the warning by calling ieee80211_mgd_stop() first.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since mesh powersaving was added, pending bcast/mcast frames may go out the
CAB queue now. Unfortunately, the queue was only set up for AP mode, so we
would try to tx on the IEEE80211_INVAL_HW_QUEUE. Allow cab_queue for mesh
interfaces as well.
Fixes the following warning (or crash without MAC80211_VERBOSE_DEBUG):
WARNING: at net/mac80211/tx.c:1223 __ieee80211_tx+0x162/0x35f [mac80211]()
Modules linked in: mac80211_hwsim mac80211 cfg80211 [...]
Pid: 3085, comm: avahi-daemon Tainted: G W 3.8.0-rc1+ #377
Call Trace:
[<ffffffff81045c20>] warn_slowpath_common+0x83/0x9c
[<ffffffff81045c53>] warn_slowpath_null+0x1a/0x1c
[<ffffffffa083aef0>] __ieee80211_tx+0x162/0x35f [mac80211]
[<ffffffffa083cb1d>] ieee80211_tx+0xd3/0xf9 [mac80211]
[<ffffffffa083cc0f>] ieee80211_xmit+0xcc/0xd5 [mac80211]
[<ffffffffa083db59>] ieee80211_subif_start_xmit+0xc53/0xcd8 [mac80211]
[<ffffffff81319acd>] dev_hard_start_xmit+0x259/0x3ce
[<ffffffff81333d6b>] sch_direct_xmit+0x74/0x17d
[<ffffffff8131a0b1>] dev_queue_xmit+0x230/0x414
[<ffffffff8134877a>] ip_finish_output2+0x348/0x3aa
[<ffffffff81349029>] ip_finish_output+0x6c/0x71
[<ffffffff81349046>] NF_HOOK_COND.constprop.44+0x18/0x58
[<ffffffff8134a03a>] ip_mc_output+0x134/0x13c
[<ffffffff8134835a>] dst_output+0x18/0x1c
[<ffffffff81349a24>] ip_local_out+0x20/0x24
[<ffffffff8134a8cf>] ip_send_skb+0x16/0x3c
[<ffffffff8136bfba>] udp_send_skb+0x254/0x2b9
[<ffffffff8136c85e>] udp_sendmsg+0x5a8/0x7d4
Signed-off-by: Bob Copeland <bob@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the vlan device is removed, ps->bc_buf processing can no longer
send its frames.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add command to trigger radar detection in the driver/FW.
Once radar detection is started it should continuously
monitor for radars as long as the channel active.
If radar is detected usermode notified with 'radar
detected' event.
Scanning and remain on channel functionality must be disabled
while doing radar detection/scanning, and vice versa.
Based on original patch by Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Now that we have channel contexts, idle is (pretty
much) equivalent to not having a channel context.
Change the code to use this relation so that there
no longer is a need for a lot of idle recalculate
calls everywhere.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are only a few drivers that use HW scan, and
all of those don't need a non-idle transition before
starting the scan -- some don't even care about idle
at all. Remove the flag and code associated with it.
The only driver that really actually needed this is
wl1251 and it can just do it itself in the hw_scan
callback -- implement that.
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add debugfs driver callbacks so drivers can add
debugfs entries for interfaces. Note that they
_must_ remove the entries again as add/remove in
the driver doesn't correspond to add/remove in
debugfs; the former is up/down while the latter
is netdev create/destroy.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Depending on the driver, having ARP filtering for
some addresses may be possible. Remove the logic
that tracks whether ARP filter is enabled or not
and give the driver the total number of addresses
instead of the length of the list so it can make
its own decision.
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of checking every time bss_info_changed is called,
assign the pointer once depending on the interface type
and then leave it untouched until the interface type is
changed. This makes the ieee80211_bss_info_change_notify()
now a simple wrapper to call the driver only.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If there are VLANs, stopping an AP is inefficient as it
calls rcu_barrier() once for each interface (the VLANs
and the AP itself). Optimise this by moving rcu_barrier()
out of the station cleanups and calling it only once for
all interfaces combined.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The last fixes re-added the RCU synchronize penalty
on roaming to fix the races. Split up sta_info_flush()
now to get rid of that again, and let managed mode
(and only it) delay the actual destruction.
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When an interface is brought down it must have been
disconnected (or similar) in all modes other than WDS,
so warn if any stations were removed in other modes.
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When all interfaces have been removed, there can't
be any stations left over, so there's no need to
flush again. Remove this, and all code associated
with it, which also simplifies the function.
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The maximum MTU shouldn't take the headers into account,
the maximum MSDU size is exactly the maximum MTU.
Signed-off-by: T Krishna Chaitanya <chaitanyatk@posedge.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Unfortunately, commit b22cfcfcae, intended to speed up roaming
by avoiding the synchronize_rcu() broke AP/mesh modes as it moved
some code into that work item that will still call into the driver
at a time where it's no longer expected to handle this: after the
AP or mesh has been stopped.
To fix this problem remove the per-station work struct, maintain a
station cleanup list instead and flush this list when stations are
flushed. To keep this patch smaller for stable, do this when the
stations are flushed (sta_info_flush()). This unfortunately brings
back the original roaming delay; I'll fix that again in a separate
patch.
Also, Ben reported that the original commit could sometimes (with
many interfaces) cause long delays when an interface is set down,
due to blocking on flush_workqueue(). Since we now maintain the
cleanup list, this particular change of the original patch can be
reverted.
Cc: stable@vger.kernel.org [3.7]
Reported-by: Ben Greear <greearb@candelatech.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make AP_VLAN type interfaces track the AP master channel
context so they have one assigned for the various lookups.
Don't give them their own refcount etc. since they're just
slaves to the AP master.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the sdata work is pending while the interface is stopped,
we currently flush it. If it's not running this means waiting
for it to run, which could take a while if the workqueue is
backlogged. However, the work exits right away if it starts
to run while the interface is already stopping. There's no
point in waiting for that, so use cancel_work_sync() instead.
Reported-by: Ben Greear <greearb@candelatech.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a driver registers an address mask we should ensure that no
interface gets an address assigned that isn't covered by the
registered address mask. This prevents invalid configurations
from reaching the device and causing problems.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
[change function flow to reduce indentation, fix locking]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Convert mac80211 (and where necessary, some drivers a
little bit) to the new channel definition struct.
This will allow extending mac80211 for VHT, which is
currently restricted to channel contexts since there
are no drivers using that which makes it easier. As
I also don't care about VHT for drivers not using the
channel context API, I won't convert the previous API
to VHT support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Even before channel contexts/multi-channel, having a
single global TX power limit was already problematic,
in particular if two managed interfaces connected to
two APs with different power constraints. The channel
context introduction completely broke this though and
in fact I had disabled TX power configuration there
for drivers using channel contexts.
Change everything to track TX power per interface so
that different user settings and different channel
maxima are treated correctly. Also continue tracking
the global TX power though for compatibility with
applications that attempt to configure the wiphy's
TX power globally.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since cfg80211 will now call the explicit stop_ap
operation when an AP interface goes down, move all
teardown code there and remove it from interface
handling. The only thing that needs to stay is the
code to dev_close() all dependent VLANs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch prepares mac80211 for a later implementation of mesh or
ad-hoc powersave clients.
The structures related to powersave (buffer, TIM map, counters) are
moved from the AP-specific interface structure to a generic structure
that can be embedded into any interface type.
The functions related to powersave are prepared to allow easy
extension with different interface types. For example with:
+ } else if (sta->sdata->vif.type == NL80211_IFTYPE_MESH_POINT) {
+ ps = &sdata->u.mesh.ps;
Some references to the AP's beacon structure are removed where they
were obviously not used.
The patch compiles without warning and has been briefly tested as AP
interface with one client in PS mode.
Signed-off-by: Marco Porsch <marco.porsch@etit.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On each channel that the device is operating on, it
may need to listen using one or more chains depending
on the SMPS settings of the interfaces using it. The
previous channel context changes completely removed
this ability (before, it was available as the SMPS
mode).
Add per-context tracking of the required static and
dynamic RX chains and notify the driver on changes.
To achieve this, track the chains and SMPS mode used
on each virtual interface and update the channel
context whenever this changes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of operating on a single channel only,
use the new channel context infrastructure in
all mac80211 code.
This enables drivers that want to use the new
channel context infrastructure to use multiple
channels, while nothing should change for all
the other drivers that don't support it.
Right now this disables both TX power settings
and spatial multiplexing powersave. Both need
to be re-enabled on a channel context basis.
Additionally, when channel contexts are used
drop the connection when channel switch is
received rather than trying to handle it. This
will have to be improved later.
[With fixes from Eliad and Emmanuel incorporated]
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Free tx status skbs when draining power save buffers, pending frames, or
when tearing down a vif.
Fixes remaining conditions that can lead to hostapd/wpa_supplicant hangs when
running out of socket write memory.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 calls synchronize_rcu() on sta deletion,
which increase the roaming time significantly.
Convert it into a call_rcu() mechanism, in order
to avoid blocking. Since some of the cleanup
functions might sleep, schedule from the call_rcu
callback a new work that will do the actual cleanup.
In order to make sure the cleanup occurs before
the interface went down, flush local->workqueue
on ieee80211_do_stop().
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A P2P Device interface does not have a netdev, and is not
expected to be used for transmitting data, so there is no
need to assign hw queues for it.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some devices like the current iwlwifi implementation
require that the P2P interface address match the P2P
Device address (only one P2P interface is supported.)
Add the HW flag IEEE80211_HW_P2P_DEV_ADDR_FOR_INTF
that allows drivers to request that P2P Interfaces
added while a P2P Device is active get the same MAC
address by default.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
After cfg80211 got a P2P Device abstraction, add
support to mac80211. Whether it really is supported
or not will depend on whether or not the driver has
support for it, but mac80211 needs to change to be
able to support drivers that need a P2P Device.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to support using a different MAC address
for the P2P Device address we must first have a
P2P Device abstraction that can be assigned a MAC
address.
This abstraction will also be useful to support
offloading P2P operations to the device, e.g.
periodic listen for discoverability.
Currently, the driver is responsible for assigning
a MAC address to the P2P Device, but this could be
changed by allowing a MAC address to be given to
the NEW_INTERFACE command.
As it has no associated netdev, a P2P Device can
only be identified by its wdev identifier but the
previous patches allowed using the wdev identifier
in various APIs, e.g. remain-on-channel.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This could take a while (100ms+) and may delay sending assoc resp
in AP mode with WPS or P2P GO (as setting the probe resp takes place
there). We've encountered situations where the delay was big enough
to cause connection problems with devices like Galaxy Nexus.
Switch to using call_rcu with a free handler.
[Arik - rework to use plain buffer and instead of skb]
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This function was only used by mesh, and not really needed since any
interface-specific cleanup already happens in the netdev handlers.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It is not necessary to stop the mesh beacon in the mac80211 ndo_stop
handler, since cfg80211 has already left the mesh on NETDEV_GOING_DOWN
notification.
Also some improvements to ieee80211_stop_mesh():
- flush mpath entries.
- flush sta entries per-sdata so we don't remove entries belonging to
other vifs on the same hw.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Enable the carrier on WDS type interfaces only
after having added the station entry for the
WDS peer so outgoing frames will find it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of assuming the carrier is on all
the time in mesh manage it with joining
and leaving the mesh.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using hw.conf.channel is wrong as it could be the
temporary channel if any function like the beacon
get function is called while scanning or during
other temporary out-of-channel activities.
Use oper_channel instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit 870d37fc22.
This code doesn't work as cfg80211 will call
set_monitor_enabled at the wrong time and it
doesn't seem to be possible to fix this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the virtual monitor interface is requested
by the driver, it should also be iterated over
when the driver wants to iterate all active
interfaces.
To allow that protect it with the iflist_mtx.
Change-Id: I58ac5de2f4ce93d12c5a98ecd2859f60158d5d69
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Making the scan_sdata pointer usable with RCU makes
it possible to dereference it in the RX path to see
if a received frame actually matches the interface
that is scanning. This is just preparations, making
the pointer __rcu.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to be able to create P2P Device wdevs, move
the virtual interface management over to wireless_dev
structures.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use cfg80211 the new .set_monitor_enabled instead
of tracking it inside mac80211.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since it's not called from any file outside where
it's defined, the function can be static if moved
up in the file before the callers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_check_concurrent_iface() need not use the
netdev. Remove the use of the netdev here to prepare
the function for P2P device addition.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a few things that make the logging and
debugging in mac80211 less useful than it should
be right now:
* a lot of messages should be pr_info, not pr_debug
* wholesale use of pr_debug makes it require *both*
Kconfig and dynamic configuration
* there are still a lot of ifdefs
* the style is very inconsistent, sometimes the
sdata->name is printed in front
Clean up everything, introducing new macros and
separating out the station MLME debugging into
a new Kconfig symbol.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Save and configure the wmm_acm per sdata, rather than
per hardware.
If wmm_acm is saved per hardware when running two
interfaces simultaneously on the same hardware one
interface's wmm policy will be affected by the other
interface.
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Redesign all the off-channel code, getting rid of
the generic off-channel work concept, replacing
it with a simple remain-on-channel list.
This fixes a number of small issues with the ROC
implementation:
* offloaded remain-on-channel couldn't be queued,
now we can queue it as well, if needed
* in iwlwifi (the only user) offloaded ROC is
mutually exclusive with scanning, use the new
queue to handle that case -- I expect that it
will later depend on a HW flag
The bigger issue though is that there's a bad bug
in the current implementation: if we get a mgmt
TX request while HW roc is active, and this new
request has a wait time, we actually schedule a
software ROC instead since we can't guarantee the
existing offloaded ROC will still be that long.
To fix this, the queuing mechanism was needed.
The queuing mechanism for offloaded ROC isn't yet
optimal, ideally we should add API to have the HW
extend the ROC if needed. We could add that later
but for now use a software implementation.
Overall, this unifies the behaviour between the
offloaded and software-implemented case as much
as possible.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The IDLE handling in HW off-channel is broken right
now since we turn off IDLE only when the off-channel
period already started. Therefore, all drivers that
use it today (only iwlwifi!) must support off-channel
while idle, so playing with idle isn't needed at all.
Off-channel in general, since it's no longer used for
authentication/association, shouldn't affect PS, so
also remove that logic.
Also document a small caveat for reporting TX status
from off-channel frames in HW remain-on-channel.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Standardize the debugging to be able to use dynamic_debug.
Coalesce formats, align arguments.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Low level drivers can now set certain netdev feature bits in
netdev_features member of the ieee80211_hw struct. These will be
propagated to every netdev created from this HW.
The white-listed features currently include only ones related to HW
checksumming.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When any interface goes down, it could be the one that we
were doing a remain-on-channel with. We therefore need to
cancel the remain-on-channel and flush the related work
structs so they don't run after the interface has been
removed or even destroyed.
It's also possible in this case that an off-channel SKB
was never transmitted, so free it if this is the case.
Note that this can also happen if the driver finishes
the off-channel period without ever starting it.
Cc: stable@kernel.org
Reported-by: Nirav Shah <nirav.j2.shah@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My queue management rework broke drivers that don't
have multiple AC queues and register a single queue
only, causing a warning:
WARNING: at net/mac80211/iface.c:162 ieee80211_check_queues
This was due to filling the queues wrongly and then
noticing the error when checking later.
Reported-and-Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.
Done via cocci script:
$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
- !compare_ether_addr(a, b)
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- compare_ether_addr(a, b)
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) == 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) != 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) == 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) != 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal(a, b)
+ ether_addr_equal(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/intel/e1000e/param.c
drivers/net/wireless/iwlwifi/iwl-agn-rx.c
drivers/net/wireless/iwlwifi/iwl-trans-pcie-rx.c
drivers/net/wireless/iwlwifi/iwl-trans.h
Resolved the iwlwifi conflict with mainline using 3-way diff posted
by John Linville and Stephen Rothwell. In 'net' we added a bug
fix to make iwlwifi report a more accurate skb->truesize but this
conflicted with RX path changes that happened meanwhile in net-next.
In e1000e a conflict arose in the validation code for settings of
adapter->itr. 'net-next' had more sophisticated logic so that
logic was used.
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds hepler to clean sdata ieee80211_clean_sdata similar way as
ieee80211_setup_sdata is implemented. The function will be used by other
interfaces later.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 3a25a8c8 (mac80211: add improved HW queue control) introduced a
bug when running in AP mode without the IEEE80211_HW_QUEUE_CONTROL
flag set. The ieee80211_check_queues() function always returns
-EINVAL, preventing AP mode from starting. To fix this, check whether
this flag is set before checking if cab_queue is set properly.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eliad's comment prompted me to look closer at
the error paths in ieee80211_do_open() and I
found one that should use the error labels.
Also add a comment about the clear_bit since
in many error cases the bit hasn't been set.
Cc: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 currently only supports one hardware queue
per AC. This is already problematic for off-channel
uses since if we go off channel while the BE queue
is full and then try to send an off-channel frame
the frame will never go out. This will become worse
when we support multi-channel since then a queue on
one channel might be full, but we have to stop the
software queue for all channels. That is obviously
not desirable.
To address this problem allow drivers to register
more hardware queues, and allow them to map them to
virtual interfaces. When they stop a hardware queue
the corresponding AC software queues on the correct
interfaces will be stopped as well. Additionally,
there's an off-channel queue to solve that problem
and a per-interface after-DTIM beacon queue. This
allows drivers to manage software queues closer to
how the hardware works.
Currently, there's a limit of 16 hardware queues.
This may or may not be sufficient, we can adjust it
as needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The queue mapping redesign that I'm planning to do
will break pure injection unless we handle monitor
interfaces explicitly. One possible option would
be to have the driver tell mac80211 about monitor
mode queues etc., but that would duplicate the API
since we already need to have queue assignments
handled per virtual interface.
So in order to solve this, have a virtual monitor
interface that is added whenever all active vifs
are monitors. We could also use the state of one
of the monitor interfaces, but managing that would
be complicated, so allocate separate state.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AP netdev is really only active when beaconing, so
manage the carrier state accordingly. Also do that for
VLAN interfaces enslaved to a given AP interface.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When comparing hw->queues to determine if the
device is QoS capable, use IEEE80211_NUM_ACS
instead of just 4.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we get more hardware queues, we'll still want
to only have netdev queues per AC, so set it up in
that way. If the hardware doesn't support QoS (by
not supporting at least 4 queues) the netdevs get
a single queue only (this is no change in behavior
as there are no drivers with 2 or 3 queues today.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When associating and particularly when disassociating
there's no need to notify the driver about changes
with multiple calls to bss_info_changed, we should
combine the QoS enabling/disabling into the same call
as otherwise the driver could get confused about QoS
suddenly getting disabled while connected.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When removing an interface while it is in the
process of authenticating or associating, we
leak the auth_data or assoc_data, and leave
the timer pending. The timer then crashes the
system when it fires as its data is gone.
Fix this by explicitly deleting all the data
when the interface is removed. This uncovered
another bug -- this problem should have been
detected by the sta_info_flush() warning but
that function doesn't ever return non-zero,
I'll fix that in a separate patch.
Reported-by: Hieu Nguyen <hieux.c.nguyen@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
nothing needs to be done for monitor/AP_VLAN mode on calling
ieee80211_bss_info_change_notify -> drv_bss_info_changed with the change
flag 'BSS_CHANGED_IDLE'. 'wl1271' seems to use BSS_CHANGED_IDLE only for
STA and IBSS mode. further the non-idle state of the monitor mode is
taken care by the 'count' variable which counts non-idle interfaces.
ieee80211_idle_off(local, "in use") will be called.
this fixes the following WARNING when we have initially STA mode
(network manager running) and not associated, and change it to monitor
mode with network manager disabled and bringing up the monitor mode.
this changes the idle state from 'true' (STA unassociated) to 'false'
(MONITOR mode)
exposed by the commit 405385f8ce
"mac80211: set bss_conf.idle when vif is connected"
WARNING: net/mac80211/main.c:212
ieee80211_bss_info_change_notify+0x1cf/0x330 [mac80211]()
Hardware name: 64756D6
Pid: 3835, comm: ifconfig Tainted: G O
3.3.0-rc3-wl #9
Call Trace:
[<c0133b02>] warn_slowpath_common+0x72/0xa0
[<fc8e8c3f>] ?
ieee80211_bss_info_change_notify+0x1cf/0x330 [mac80211]
[<fc8e8c3f>] ?
ieee80211_bss_info_change_notify+0x1cf/0x330 [mac80211]
[<c0133b52>] warn_slowpath_null+0x22/0x30
[<fc8e8c3f>]
ieee80211_bss_info_change_notify+0x1cf/0x330 [mac80211]
[<fc8f9de3>] __ieee80211_recalc_idle+0x113/0x430
[mac80211]
[<fc8fabc6>] ieee80211_do_open+0x156/0x7e0 [mac80211]
[<fc8f8a25>] ?
ieee80211_check_concurrent_iface+0x25/0x180 [mac80211]
[<c015dd9f>] ? raw_notifier_call_chain+0x1f/0x30
[<fc8fb290>] ieee80211_open+0x40/0x80 [mac80211]
[<c05894f6>] __dev_open+0x96/0xe0
[<c068fba5>] ? _raw_spin_unlock_bh+0x35/0x40
[<c05881d9>] __dev_change_flags+0x109/0x170
[<c0589423>] dev_change_flags+0x23/0x60
[<c05f3770>] devinet_ioctl+0x6a0/0x770
ieee80211 phy0: device no longer idle - in use
Cc: Eliad Peller <eliad@wizery.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, mac80211 goes to idle-off before starting a scan.
However, some devices that implement hw scan might not
need going idle-off in order to perform a hw scan, and
thus saving some energy and simplifying their state machine.
(Note that this is also the case for sched scan - it
currently doesn't make mac80211 go idle-off)
Add a new flag to indicate support for hw scan while idle.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is the second part of the auth/assoc redesign,
the mac80211 part. This moves the auth/assoc code
out of the work abstraction and into the MLME, so
that we don't flip channels all the time etc.
The only downside is that when we are associated,
we need to drop the association in order to create
a connection to another AP, but for most drivers
this is actually desirable and the ability to do
was never used by any applications. If we want to
implement resource reservation with FT-OTA, we'd
probably best do it with explicit R-O-C in wpa_s.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Handle MCS masks set by the user.
* Match rates provided by the rate control algorithm to the mask set,
also in HT mode, and switch back to legacy mode if necessary.
* add debugfs files to observate the rate selection
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the future, when we start notifying drivers,
state transitions could potentially fail. To make
it easier to distinguish between programming bugs
and driver failures:
* rename sta_info_move_state() to
sta_info_pre_move_state() which can only be
called before the station is inserted (and
check this with a new station flag).
* rename sta_info_move_state_checked() to just
plain sta_info_move_state(), as it will be
the regular function that can fail for more
than just one reason (bad transition or an
error from the driver)
This makes the programming model easier -- one of
the functions can only be called before insertion
and can't fail, the other can fail.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
__ieee80211_recalc_idle() iterates through the vifs,
sets bss_conf.idle = true if they are disconnected,
and increases "count" if they are not (which later
gets evaluated in order to determine whether the
device is idle).
However, the loop doesn't set bss_conf.idle = false
(along with increasing "count"), causing the device
idle state and the vif idle state to get out of sync
in some cases.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Station entries can have various states, the most
important ones being auth, assoc and authorized.
This patch prepares us for telling the driver about
these states, we don't want to confuse drivers with
strange transitions, so with this we enforce that
they move in the right order between them (back and
forth); some transitions might happen before the
driver even knows about the station, but at least
runtime transitions will be ordered correctly.
As a consequence, IBSS and MESH stations will now
have the ASSOC flag set (so they can transition to
AUTHORIZED), and we can get rid of a special case
in TX processing.
When freeing a station, unwind the state so that
other parts of the code (or drivers later) can rely
on the transitions.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can't rely on ieee80211_select_queue() to do its job at this point
since the skb->protocol is not yet known. Instead, factor out and reuse
the queue mapping logic for injected frames.
Also, to mitigate congestion, forwarded frames should be dropped if the
outgoing queue was stopped. This was not correctly implemented as we
were not checking the right queue. Furthermore, we were dropping frames
that had arrived to their destination if that queue was stopped.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch contains the processing changes in mac80211.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sk_buff structs should be freed using kfree_skb().
This was introduced recently in 029458212 "mac80211: Save probe
response data for bss".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow setting a probe response template for an interface operating in
AP mode. Low level drivers are notified about changes in the probe
response template and are able to retrieve a copy of the current probe
response. This data can, for example, be uploaded to hardware as a
template.
Signed-off-by: Guy Eilam <guy@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 should set carrier_on for ibss vifs
only while they are joined (similar to sta vifs)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will allow us to support dynamic WEP with 802.1X
properly in mac80211 by not encrypting outgoing and
accepting unencrypted incoming frames.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver is never informed about monitor or
AP_VLAN interfaces, so whenever we pass those
to it later this is a bug. Verify we don't as
there are some cases where this could happen.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 calls ieee80211_set_wmm_default (which in turn
calls drv_conf_tx()) for every new interface, including
"internal" ones (e.g. monitor interface, which the low-level
driver doesn't know about).
Limit this call only to valid interfaces.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The flaglock in struct sta_info has long been
something that I wanted to get rid of, this
finally does the conversion to atomic bitops.
The conversion itself is straight-forward in
most places, a few things needed to change a
bit since we can no longer use multiple bits
at the same time.
On x86-64, this is a fairly significant code
size reduction:
text data bss dec hex
427861 23648 1008 452517 6e7a5 before
425383 23648 976 450007 6ddd7 after
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an AP interface is removed without the
AP/VLAN interfaces having been removed before
already, the AP-VLAN interface might still
have sleeping stations and buffer multicast
frames which will happen on the AP interface.
Thus, we need to remove AP/VLAN interfaces
before purging buffered broadcast frames.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an interface is removed, the mesh paths associated with it should
also be removed.
This fixes a bug we observed when reloading a device driver module
without reloading mac80211s.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When assigning a NULL value to an RCU protected pointer, no barrier
is needed. The rcu_assign_pointer, used to handle that but will soon
change to not handle the special case.
Convert all rcu_assign_pointer of NULL value.
//smpl
@@ expression P; @@
- rcu_assign_pointer(P, NULL)
+ RCU_INIT_POINTER(P, NULL)
// </smpl>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the last patch, We are left in a state in which only drivers calling
ether_setup have IFF_TX_SKB_SHARING set (we assume that drivers touching real
hardware call ether_setup for their net_devices and don't hold any state in
their skbs. There are a handful of drivers that violate this assumption of
course, and need to be fixed up. This patch identifies those drivers, and marks
them as not being able to support the safe transmission of skbs by clearning the
IFF_TX_SKB_SHARING flag in priv_flags
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Karsten Keil <isdn@linux-pingi.de>
CC: "David S. Miller" <davem@davemloft.net>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Patrick McHardy <kaber@trash.net>
CC: Krzysztof Halasa <khc@pm.waw.pl>
CC: "John W. Linville" <linville@tuxdriver.com>
CC: Greg Kroah-Hartman <gregkh@suse.de>
CC: Marcel Holtmann <marcel@holtmann.org>
CC: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
is_valid_ether_addr itself checks for is_zero_ether_addr
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg