Member "status" of struct usb_sg_request is managed by usb core. A
spin lock is used to serialize the change of it. The driver could
check the value of req->status, but should avoid changing it without
the hold of the spinlock. Otherwise, it could cause race or error
in usb core.
This patch could be backported to stable kernels with version later
than v3.14.
Cc: stable@vger.kernel.org # 3.14+
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
A card insertion happens after the lastest polling before reader is
suspended may never have a chance to be detected. Under current 1-HZ
polling interval setting in mmc_core, the worst case of such
undetectablility is about 1 second.
To further reduce the undetectability, detect card slot again in suspend
method and defer the autosuspend if the slot is loaded. The default 2
second autosuspend delay of USB subsystem should let the next polling
detects the card.
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
sd_set_power_mode() in derived module drivers/mmc/host/rtsx_usb_sdmmc.c
acquires dev_mutex and then calls pm_runtime_get_sync() to make sure the
device is awake while initializing a newly inserted card. Once it is
called during suspending state and explicitly before rtsx_usb_suspend()
acquires the same dev_mutex, both routine deadlock and further hang the
driver because pm_runtime_get_sync() waits the pending PM operations.
Fix this by using an empty suspend method. mmc_core always turns the
LED off after a request is done and thus it is ok to remove the only
rtsx_usb_turn_off_led() here.
Cc: <stable@vger.kernel.org> # v3.16+
Fixes: 730876be25 ("mfd: Add realtek USB card reader driver")
Signed-off-by: Roger Tseng <rogerable@realtek.com>
[Lee: Removed newly unused variable]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use mfd_add_hotplug_devices helper to register the subdevices.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The prefix suggests the number should be printed in hex, so use
the %x specifier to do that.
Found by using regex suggested by Joe Perches.
Signed-off-by: Hans Wennborg <hans@hanshq.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The rtsx_usb driver contains the table for the devices it supports but
doesn't export it. As a result, no alias is generated and it doesn't
get loaded automatically.
Via https://bugzilla.novell.com/show_bug.cgi?id=890096
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Reported-by: Marcel Witte <wittemar@googlemail.com>
Cc: Roger Tseng <rogerable@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mfd_add_devices() expects array of struct mfd_cell to be const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Explain why there is no need to have a symmetric LED turn-on in resume handler
while calling rtsx_usb_turn_off_led() in suspend handler.
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fix two possible race condition generated by misuse of del_timer in
rtsx_usb_bulk_transfer_sglist() and uninitialized timers before mfd_add_devices
in rtsx_usb_probe().
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Realtek USB card reader provides a channel to transfer command or data to flash
memory cards. This driver exports host instances for mmc and memstick subsystems
and handles basic works.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Kees Cook