We are keeping track of the maximum register as well, this will make
things easier for us in sharing this code with the code implementing
the register ranges functionality. It also simplifies a bit the
calculations when looking for the relevant block:offset from within
the cache.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
PM_SUSPEND_FREEZE state is a general state that
does not need any platform specific support, it equals
frozen processes + suspended devices + idle processors.
Compared with PM_SUSPEND_MEMORY,
PM_SUSPEND_FREEZE saves less power
because the system is still in a running state.
PM_SUSPEND_FREEZE has less resume latency because it does not
touch BIOS, and the processors are in idle state.
Compared with RTPM/idle,
PM_SUSPEND_FREEZE saves more power as
1. the processor has longer sleep time because processes are frozen.
The deeper c-state the processor supports, more power saving we can get.
2. PM_SUSPEND_FREEZE uses system suspend code path, thus we can get
more power saving from the devices that does not have good RTPM support.
This state is useful for
1) platforms that do not have STR, or have a broken STR.
2) platforms that have an extremely low power idle state,
which can be used to replace STR.
The following describes how PM_SUSPEND_FREEZE state works.
1. echo freeze > /sys/power/state
2. the processes are frozen.
3. all the devices are suspended.
4. all the processors are blocked by a wait queue
5. all the processors idles and enters (Deep) c-state.
6. an interrupt fires.
7. a processor is woken up and handles the irq.
8. if it is a general event,
a) the irq handler runs and quites.
b) goto step 4.
9. if it is a real wake event, say, power button pressing, keyboard touch, mouse moving,
a) the irq handler runs and activate the wakeup source
b) wakeup_source_activate() notifies the wait queue.
c) system starts resuming from PM_SUSPEND_FREEZE
10. all the devices are resumed.
11. all the processes are unfrozen.
12. system is back to working.
Known Issue:
The wakeup of this new PM_SUSPEND_FREEZE state may behave differently
from the previous suspend state.
Take ACPI platform for example, there are some GPEs that only enabled
when the system is in sleep state, to wake the system backk from S3/S4.
But we are not touching these GPEs during transition to PM_SUSPEND_FREEZE.
This means we may lose some wake event.
But on the other hand, as we do not disable all the Interrupts during
PM_SUSPEND_FREEZE, we may get some extra "wakeup" Interrupts, that are
not available for S3/S4.
The patches has been tested on an old Sony laptop, and here are the results:
Average Power:
1. RPTM/idle for half an hour:
14.8W, 12.6W, 14.1W, 12.5W, 14.4W, 13.2W, 12.9W
2. Freeze for half an hour:
11W, 10.4W, 9.4W, 11.3W 10.5W
3. RTPM/idle for three hours:
11.6W
4. Freeze for three hours:
10W
5. Suspend to Memory:
0.5~0.9W
Average Resume Latency:
1. RTPM/idle with a black screen: (From pressing keyboard to screen back)
Less than 0.2s
2. Freeze: (From pressing power button to screen back)
2.50s
3. Suspend to Memory: (From pressing power button to screen back)
4.33s
>From the results, we can see that all the platforms should benefit from
this patch, even if it does not have Low Power S0.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
At the moment, if the length of the register field format is
N bytes, we can only get anything meaningful back to userspace
by providing a buffer that is N + 2 bytes large. Fix this
so we that we only need to provide a buffer of N bytes.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
All in-kernel users of class_find_device() don't really need mutable
data for match callback.
In two places (kernel/power/suspend_test.c, drivers/scsi/osd/osd_uld.c)
this patch changes match callbacks to use const search data.
The const is propagated to rtc_class_open() and power_supply_get_by_name()
parameters.
Note that there's a dev reference leak in suspend_test.c that's not
touched in this patch.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes:
drivers/base/regmap/regmap.c: In function 'regmap_async_complete_cb':
drivers/base/regmap/regmap.c:1656:3: error: 'TASK_NORMAL' undeclared (first use in this function)
drivers/base/regmap/regmap.c:1656:3: note: each undeclared identifier is reported only once for each function it appears in
drivers/base/regmap/regmap.c: In function 'regmap_async_complete':
drivers/base/regmap/regmap.c:1688:2: error: 'TASK_UNINTERRUPTIBLE' undeclared (first use in this function)
drivers/base/regmap/regmap.c:1688:2: error: implicit declaration of function 'schedule'
An alternative might be to adjust linux/wait.h to include linux/sched.h,
but since that hasn't been done before, I assume we're consciously
avoiding doing that.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
FW_STATUS_ABORT can be set only during the user-helper invocation,
thus we can ignore the check when CONFIG_HW_LOADER_USER_HELPER is
disabled.
Acked-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By shuffling the code, reduce a few ifdefs in firmware_class.c.
Also, firmware_buf fmt field is changed to is_pages_buf boolean for
simplification.
Acked-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a new kconfig, CONFIG_FW_LOADER_USER_HELPER, and
guards the user-helper codes in firmware_class.c with ifdefs.
Yeah, yeah, there are lots of ifdefs in this patch. The further
clean-up with code shuffling follows in the next.
Acked-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since 3.7 kernel, the firmware loader can read the firmware files
directly, and the traditional user-mode helper is invoked only as a
fallback. This seems working pretty well, and the next step would be
to reduce the redundant user-mode helper stuff in future.
This patch is a preparation for that: refactor the code for splitting
user-mode helper stuff more easily. No functional change.
Acked-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A bus_type has a list of devices (klist_devices), but the list and the
subsys_private structure that contains it are not initialized until the
bus_type is registered with bus_register().
The panic/reboot path has fixups that look up devices in pci_bus_type. If
we panic before registering pci_bus_type, the bus_type exists but the list
does not, so mach_reboot_fixups() trips over a null pointer and panics
again:
mach_reboot_fixups
pci_get_device
..
bus_find_device(&pci_bus_type, ...)
bus->p is NULL
Joonsoo reported a problem when panicking before PCI was initialized.
I think this patch should be sufficient to replace the patch he posted
here: https://lkml.org/lkml/2012/12/28/75 ("[PATCH] x86, reboot: skip
reboot_fixups in early boot phase")
Reported-by: Joonsoo Kim <js1304@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Export cpufreq helpers in OPP to make the cpufreq-core0 and highbank-cpufreq
drivers loadable as modules.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We are GPLV2 library, so be clear in the symbols exported as well.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some use cases like firmware download can transfer a lot of data in quick
succession. With high speed buses these use cases can benefit from having
multiple transfers scheduled at once since this allows the bus to minimise
the delay between transfers.
Support this by adding regmap_raw_write_async(), allowing raw transfers to
be scheduled, and regmap_async_complete() to wait for them to finish.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This commit adds provision for "no-bus" usage of the regmap API. In
this configuration user can provide API with two callbacks 'reg_read'
and 'reg_write' which are to be called when reads and writes to one of
device's registers is performed. This is useful for devices that
expose registers but whose register access sequence does not fit the 'bus'
abstraction.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Gcc warns about the case where regmap_read_debugfs tries to walk an
empty map->debugfs_off_cache list, which would results in uninitialized
variable getting returned, if we hadn't checked the same condition
just before that.
After an originally suggested inferior patch from Arnd Bergmann,
this is the solution that Russell King came up with, sidestepping
the problem by merging the error case for an empty list with the
normal path.
Without this patch, building mxs_defconfig results in:
drivers/base/regmap/regmap-debugfs.c: In function 'regmap_read_debugfs':
drivers/base/regmap/regmap-debugfs.c:147:9: : warning: 'ret' may be used uninitialized in this function [-Wmaybe-uninitialized]
Reported-by: Vincent Stehle <v-stehle@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There's no need to test whether a (delayed) work item is pending
before queueing, flushing or cancelling it, so remove work_pending()
tests used in those cases.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The dev_pm_qos_flags() will be used in the usb core which could be
compiled as a module. This patch is to export it.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This makes the device core auto-grab the pinctrl handle and set
the "default" (PINCTRL_STATE_DEFAULT) state for every device
that is present in the device model right before probe. This will
account for the lion's share of embedded silicon devcies.
A modification of the semantics for pinctrl_get() is also done:
previously if the pinctrl handle for a certain device was already
taken, the pinctrl core would return an error. Now, since the
core may have already default-grabbed the handle and set its
state to "default", if the handle was already taken, this will
be disregarded and the located, previously instanitated handle
will be returned to the caller.
This way all code in drivers explicitly requesting their pinctrl
handlers will still be functional, and drivers that want to
explicitly retrieve and switch their handles can still do that.
But if the desired functionality is just boilerplate of this
type in the probe() function:
struct pinctrl *p;
p = devm_pinctrl_get_select_default(&dev);
if (IS_ERR(p)) {
if (PTR_ERR(p) == -EPROBE_DEFER)
return -EPROBE_DEFER;
dev_warn(&dev, "no pinctrl handle\n");
}
The discussion began with the addition of such boilerplate
to the omap4 keypad driver:
http://marc.info/?l=linux-input&m=135091157719300&w=2
A previous approach using notifiers was discussed:
http://marc.info/?l=linux-kernel&m=135263661110528&w=2
This failed because it could not handle deferred probes.
This patch alone does not solve the entire dilemma faced:
whether code should be distributed into the drivers or
if it should be centralized to e.g. a PM domain. But it
solves the immediate issue of the addition of boilerplate
to a lot of drivers that just want to grab the default
state. As mentioned, they can later explicitly retrieve
the handle and set different states, and this could as
well be done by e.g. PM domains as it is only related
to a certain struct device * pointer.
ChangeLog v4->v5 (Stephen):
- Simplified the devicecore grab code.
- Deleted a piece of documentation recommending that pins
be mapped to a device rather than hogged.
ChangeLog v3->v4 (Linus):
- Drop overzealous NULL checks.
- Move kref initialization to pinctrl_create().
- Seeking Tested-by from Stephen Warren so we do not disturb
the Tegra platform.
- Seeking ACK on this from Greg (and others who like it) so I
can merge it through the pinctrl subsystem.
ChangeLog v2->v3 (Linus):
- Abstain from using IS_ERR_OR_NULL() in the driver core,
Russell recently sent a patch to remove it. Handle the
NULL case explicitly even though it's a bogus case.
- Make sure we handle probe deferral correctly in the device
core file. devm_kfree() the container on error so we don't
waste memory for devices without pinctrl handles.
- Introduce reference counting into the pinctrl core using
<linux/kref.h> so that we don't release pinctrl handles
that have been obtained for two or more places.
ChangeLog v1->v2 (Linus):
- Only store a pointer in the device struct, and only allocate
this if it's really used by the device.
Cc: Felipe Balbi <balbi@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Mitch Bradley <wmb@firmworks.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Rickard Andersson <rickard.andersson@stericsson.com>
Cc: Russell King <linux@arm.linux.org.uk>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[swarren: fixed and simplified error-handling in pinctrl_bind_pins(), to
correctly handle deferred probe. Removed admonition from docs not to use
pinctrl hogs for devices]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix up all callers as they were before, with make one change: an
unsigned module taints the kernel, but doesn't turn off lockdep.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This is to fix up a build problem with a wireless driver due to the
dynamic-debug patches in this branch.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit e797986593 as %pSR
isn't in the tree yet.
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Inside bus_add_driver(), one device might be added(device_add()) into
the bus or probed which is triggered by deferred probe
just after completing of driver_attach() and before
'klist_add_tail(&priv->knode_bus, &bus->p->klist_drivers)',
so the device won't be probed by this driver.
This patch moves the below line
'klist_add_tail(&priv->knode_bus, &bus->p->klist_drivers)'
before driver_attach() inside bus_add_driver() to fix the
problem.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the new vsprintf extension to avoid any possible
message interleaving.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
old_class_name, and new_class_name are never used. This patch remove the
declaration and calls to kfree.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r1 forall@
type T; identifier i;
@@
* T *i = NULL;
... when != i
* kfree(i);
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ We should make fun of people who can't speel too, but then we'd have
no time for any real work at all - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the requested firmware file size is 0 bytes in the filesytem, we
will try to vmalloc(0), which causes a warning:
vmalloc: allocation failure: 0 bytes
kworker/1:1: page allocation failure: order:0, mode:0xd2
__vmalloc_node_range+0x164/0x208
__vmalloc_node+0x4c/0x58
vmalloc+0x38/0x44
_request_firmware_load+0x220/0x6b0
request_firmware+0x64/0xc8
wl18xx_setup+0xb4/0x570 [wl18xx]
wlcore_nvs_cb+0x64/0x9f8 [wlcore]
request_firmware_work_func+0x94/0x100
process_one_work+0x1d0/0x750
worker_thread+0x184/0x4ac
kthread+0xb4/0xc0
To fix this, check whether the file size is less than or equal to zero
in fw_read_file_contents().
Cc: stable <stable@vger.kernel.org> [3.7]
Signed-off-by: Luciano Coelho <coelho@ti.com>
Acked-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We don't want to bomb out early if we failed to get the cache any more,
just soldier on instead and we won't get confused and always return the
first block.
Reported-by: Philipp Zabel <p.zabel@pengutronix.de
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The debugfs optimisations merged in v3.8 weren't my finest hour, there
were a number of cases that the more complex algorithm made worse
especially around the error handling. This patch series should address
those issues.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=unOt
-----END PGP SIGNATURE-----
Merge tag 'regmap-debugfs-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap debugfs optimisation fixes from Mark Brown:
"The debugfs optimisations merged in v3.8 weren't my finest hour, there
were a number of cases that the more complex algorithm made worse
especially around the error handling. This patch series should
address those issues."
* tag 'regmap-debugfs-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: debugfs: Make sure we store the last entry in the offset cache
regmap: debugfs: Ensure a correct return value for empty caches
regmap: debugfs: Discard the cache if we fail to allocate an entry
regmap: debugfs: Fix check for block start in cached seeks
regmap: debugfs: Fix attempts to read nonexistant register blocks
This commit is a preparatory commit to provide "no-bus" configuration
option for regmap API. It adds necessary plumbing needed to have the
ability to provide user define register write function.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This commit is a preparatory commit to provide "no-bus" configuration
option for regmap API. It adds necessary plumbing needed to have the
ability to provide user define register read function.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since regmap already has support for formatting 24 bit wide values, so adding
support for 24 bit wide registers is pretty much straight forward.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rather than trying to soldier on with a partially allocated cache just
throw the cache away and pretend we don't have one in case we can get a
full cache next time around.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Return the start of the last block we tried to read rather than a position,
and also make sure we update the byte position while we're at it. Without
this reads that go into nonexistant areas get confused.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently, the PM core disables runtime PM for all devices right
after executing subsystem/driver .suspend() callbacks for them
and re-enables it right before executing subsystem/driver .resume()
callbacks for them. This may lead to problems when there are
two devices such that the .suspend() callback executed for one of
them depends on runtime PM working for the other. In that case,
if runtime PM has already been disabled for the second device,
the first one's .suspend() won't work correctly (and analogously
for resume).
To make those issues go away, make the PM core disable runtime PM
for devices right before executing subsystem/driver .suspend_late()
callbacks for them and enable runtime PM for them right after
executing subsystem/driver .resume_early() callbacks for them. This
way the potential conflitcs between .suspend_late()/.resume_early()
and their runtime PM counterparts are still prevented from happening,
but the subtle ordering issues related to disabling/enabling runtime
PM for devices during system suspend/resume are much easier to avoid.
Reported-and-tested-by: Jan-Matthias Braun <jan_braun@gmx.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: 3.4+ <stable@vger.kernel.org>
Local variable 'error' in dev_pm_qos_add_ancestor_request() need
not contain error codes only, so rename it to 'ret'.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This wasn't implemented but happened to work on test systems due to lack
of wake mask inversion support.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If the interrupt status registers are a single block of registers and the
chip supports bulk reads then do a single bulk read rather than pay the
extra I/O cost. This restores the original behaviour which was lost when
support for register striding was added.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
While for I2C and SPI devices the overhead of using rbtree for devices with
only one block of registers is negligible the same isn't always going to
be true for MMIO devices where the I/O costs are very much lower. Cater
for these devices by adding a simple flat array type for them where the
lookups are simple array accesses, taking us right back to the original
ASoC cache implementation.
Thanks to Magnus Damm for the discussion which prompted this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
regmap-irq framework is used vastly by mfd drivers and some of
devices like TPS65910, TPS80036 do not support the wake base
register to enable wake.
Currently wake in regmap-irq only supported if client driver
passes the wake base register.
As the regmap-irq is mostly used by mfd devices and it is require
to have wake support from these devices in most of use cases,
enabling wake support by default in regmap-irq.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Where we can pass in LOOKUP_DIRECTORY or LOOKUP_REVAL. Any other flags
passed in here are currently ignored.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
We never really clarified if unmap could be done in atomic context.
But since mapping might require sleeping, this implies mutex in use
to synchronize mapping/unmapping, so unmap could sleep as well. Add
a might_sleep() to clarify this.
Signed-off-by: Rob Clark <rob@ti.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Pull x86 RAS update from Ingo Molnar:
"Rework all config variables used throughout the MCA code and collect
them together into a mca_config struct. This keeps them tightly and
neatly packed together instead of spilled all over the place.
Then, convert those which are used as booleans into real booleans and
save some space. These bits are exposed via
/sys/devices/system/machinecheck/machinecheck*/"
* 'x86-ras-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, MCA: Finish mca_config conversion
x86, MCA: Convert the next three variables batch
x86, MCA: Convert rip_msr, mce_bootlog, monarch_timeout
x86, MCA: Convert dont_log_ce, banks and tolerant
drivers/base: Add a DEVICE_BOOL_ATTR macro
Pull media updates from Mauro Carvalho Chehab:
- Missing MAINTAINERS entries were added for several drivers
- Adds V4L2 support for DMABUF handling, allowing zero-copy buffer
sharing between V4L2 devices and GPU
- Got rid of all warnings when compiling with W=1 on x86
- Add a new driver for Exynos hardware (s3c-camif)
- Several bug fixes, cleanups and driver improvements
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (243 commits)
[media] omap3isp: Replace cpu_is_omap3630() with ISP revision check
[media] omap3isp: Prepare/unprepare clocks before/after enable/disable
[media] omap3isp: preview: Add support for 8-bit formats at the sink pad
[media] omap3isp: Replace printk with dev_*
[media] omap3isp: Find source pad from external entity
[media] omap3isp: Configure CSI-2 phy based on platform data
[media] omap3isp: Add PHY routing configuration
[media] omap3isp: Add CSI configuration registers from control block to ISP resources
[media] omap3isp: Remove unneeded module memory address definitions
[media] omap3isp: Use monotonic timestamps for statistics buffers
[media] uvcvideo: Fix control value clamping for unsigned integer controls
[media] uvcvideo: Mark first output terminal as default video node
[media] uvcvideo: Add VIDIOC_[GS]_PRIORITY support
[media] uvcvideo: Return -ENOTTY for unsupported ioctls
[media] uvcvideo: Set device_caps in VIDIOC_QUERYCAP
[media] uvcvideo: Don't fail when an unsupported format is requested
[media] uvcvideo: Return -EACCES when trying to access a read/write-only control
[media] uvcvideo: Set error_idx properly for extended controls API failures
[media] rtl28xxu: add NOXON DAB/DAB+ USB dongle rev 2
[media] fc2580: write some registers conditionally
...
We need a node which only contains movable memory. This feature is very
important for node hotplug. If a node has normal/highmem, the memory may
be used by the kernel and can't be offlined. If the node only contains
movable memory, we can offline the memory and the node.
All are prepared, we can actually introduce N_MEMORY.
add CONFIG_MOVABLE_NODE make we can use it for movable-dedicated node
[akpm@linux-foundation.org: fix Kconfig text]
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Tested-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Cc: Jiang Liu <jiang.liu@huawei.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: David Rientjes <rientjes@google.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
N_HIGH_MEMORY stands for the nodes that has normal or high memory.
N_MEMORY stands for the nodes that has any memory.
The code here need to handle with the nodes which have memory, we should
use N_MEMORY instead.
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Acked-by: Hillf Danton <dhillf@gmail.com>
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Hillf Danton <dhillf@gmail.com>
Cc: Lin Feng <linfeng@cn.fujitsu.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Quite a few enhancements this time around, helpers and diagnostics for
the most part which is good to see:
- Addition of table based lookups for the register access checks from
Davide Ciminaghi, making life easier for drivers with big blocks of
similar registers.
- Allow drivers to get the irqdomain for regmap irq_chips, allowing the
domain to be used with other APIs.
- Debug improvements for paged register maps.
- Performance improvments for some of the diagnostic infrastructure,
very helpful for devices with large register maps.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Jy7K
-----END PGP SIGNATURE-----
Merge tag 'regmap-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"Quite a few enhancements this time around, helpers and diagnostics for
the most part which is good to see:
- Addition of table based lookups for the register access checks from
Davide Ciminaghi, making life easier for drivers with big blocks of
similar registers.
- Allow drivers to get the irqdomain for regmap irq_chips, allowing
the domain to be used with other APIs.
- Debug improvements for paged register maps.
- Performance improvments for some of the diagnostic infrastructure,
very helpful for devices with large register maps."
* tag 'regmap-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: debugfs: Cache offsets of valid regions for dump
regmap: debugfs: Factor out initial seek
regmap: debugfs: Avoid overflows for very small reads
regmap: Cache register and value sizes for debugfs
regmap: introduce tables for readable/writeable/volatile/precious checks
regmap: core: Report registers in hex when we can't cache
regmap: Fix printing of size_t variable
regmap: make lock/unlock functions customizable
regmap: silence GCC warning
regmap: Split raw writes that cross window boundaries
regmap: Make return code checks consistent
regmap: Factor range lookup out of page selection
regmap: Provide debugfs read of register ranges
regmap: Factor out debugfs register read
regmap: Allow ranges to be named
regmap: When we sanity check during range adds say what errors we find
regmap: Rename n_ranges to num_ranges
regmap: irq: Allow users to retrieve the irq_domain
Merge misc updates from Andrew Morton:
"About half of most of MM. Going very early this time due to
uncertainty over the coreautounifiednumasched things. I'll send the
other half of most of MM tomorrow. The rest of MM awaits a slab merge
from Pekka."
* emailed patches from Andrew Morton: (71 commits)
memory_hotplug: ensure every online node has NORMAL memory
memory_hotplug: handle empty zone when online_movable/online_kernel
mm, memory-hotplug: dynamic configure movable memory and portion memory
drivers/base/node.c: cleanup node_state_attr[]
bootmem: fix wrong call parameter for free_bootmem()
avr32, kconfig: remove HAVE_ARCH_BOOTMEM
mm: cma: remove watermark hacks
mm: cma: skip watermarks check for already isolated blocks in split_free_page()
mm, oom: fix race when specifying a thread as the oom origin
mm, oom: change type of oom_score_adj to short
mm: cleanup register_node()
mm, mempolicy: remove duplicate code
mm/vmscan.c: try_to_freeze() returns boolean
mm: introduce putback_movable_pages()
virtio_balloon: introduce migration primitives to balloon pages
mm: introduce compaction and migration for ballooned pages
mm: introduce a common interface for balloon pages mobility
mm: redefine address_space.assoc_mapping
mm: adjust address_space_operations.migratepage() return code
arch/sparc/kernel/sys_sparc_64.c: s/COLOUR/COLOR/
...
Add online_movable and online_kernel for logic memory hotplug. This is
the dynamic version of "movablecore" & "kernelcore".
We have the same reason to introduce it as to introduce "movablecore" &
"kernelcore". It has the same motive as "movablecore" & "kernelcore", but
it is dynamic/running-time:
o We can configure memory as kernelcore or movablecore after boot.
Userspace workload is increased, we need more hugepage, we can't use
"online_movable" to add memory and allow the system use more
THP(transparent-huge-page), vice-verse when kernel workload is increase.
Also help for virtualization to dynamic configure host/guest's memory,
to save/(reduce waste) memory.
Memory capacity on Demand
o When a new node is physically online after boot, we need to use
"online_movable" or "online_kernel" to configure/portion it as we
expected when we logic-online it.
This configuration also helps for physically-memory-migrate.
o all benefit as the same as existed "movablecore" & "kernelcore".
o Preparing for movable-node, which is very important for power-saving,
hardware partitioning and high-available-system(hardware fault
management).
(Note, we don't introduce movable-node here.)
Action behavior:
When a memoryblock/memorysection is onlined by "online_movable", the kernel
will not have directly reference to the page of the memoryblock,
thus we can remove that memory any time when needed.
When it is online by "online_kernel", the kernel can use it.
When it is online by "online", the zone type doesn't changed.
Current constraints:
Only the memoryblock which is adjacent to the ZONE_MOVABLE
can be online from ZONE_NORMAL to ZONE_MOVABLE.
[akpm@linux-foundation.org: use min_t, cleanups]
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Jiang Liu <jiang.liu@huawei.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: David Rientjes <rientjes@google.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
use [index] = init_value
use N_xxxxx instead of hardcode.
Make it more readability and easier to add new state.
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
register_node() is defined as extern in include/linux/node.h. But the
function is only called from register_one_node() in driver/base/node.c.
So the patch defines register_node() as static.
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Acked-by: David Rientjes <rientjes@google.com>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When calling unregister_node(), the function shows following message at
device_release().
"Device 'node2' does not have a release() function, it is broken and must
be fixed."
The reason is node's device struct does not have a release() function.
So the patch registers node_device_release() to the device's release()
function for suppressing the warning message. Additionally, the patch
adds memset() to initialize a node struct into register_node(). Because
the node struct is part of node_devices[] array and it cannot be freed by
node_device_release(). So if system reuses the node struct, it has a
garbage.
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Jiang Liu <liuj97@gmail.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We use a static array to store struct node. In many cases, we don't have
too many nodes, and some memory will be unused. Convert it to per-device
dynamically allocated memory.
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Jiang Liu <liuj97@gmail.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When calling remove_memory_block(), the function shows following message
at device_release().
"Device 'memory528' does not have a release() function, it is broken and
must be fixed."
The reason is memory_block's device struct does not have a release()
function.
So the patch registers memory_block_release() to the device's release()
function for suppressing the warning message. Additionally, the patch
moves kfree(mem) into the release function since the release function is
prepared as a means to free a memory_block struct.
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Jiang Liu <liuj97@gmail.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Wen Congyang <wency@cn.fujitsu.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here's the large driver core updates for 3.8-rc1.
The biggest thing here is the various __dev* marking removals. This is
going to be a pain for the merge with different subsystem trees, I know,
but all of the patches included here have been ACKed by their various
subsystem maintainers, as they wanted them to go through here.
If this is too much of a pain, I can pull all of them out of this tree
and just send you one with the other fixes/updates and then, after
3.8-rc1 is out, do the rest of the removals to ensure we catch them all,
it's up to you. The merges should all be trivial, and Stephen has been
doing them all in linux-next for a few weeks now quite easily.
Other than the __dev* marking removals, there's nothing major here, some
firmware loading updates and other minor things in the driver core.
All of these have (much to Stephen's annoyance), been in linux-next for
a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlDHkPkACgkQMUfUDdst+ykaWgCfW7AM30cv0nzoVO08ax6KjlG1
KVYAn3z/KYazvp4B6LMvrW9y0G34Wmad
=yvVr
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg Kroah-Hartman:
"Here's the large driver core updates for 3.8-rc1.
The biggest thing here is the various __dev* marking removals. This
is going to be a pain for the merge with different subsystem trees, I
know, but all of the patches included here have been ACKed by their
various subsystem maintainers, as they wanted them to go through here.
If this is too much of a pain, I can pull all of them out of this tree
and just send you one with the other fixes/updates and then, after
3.8-rc1 is out, do the rest of the removals to ensure we catch them
all, it's up to you. The merges should all be trivial, and Stephen
has been doing them all in linux-next for a few weeks now quite
easily.
Other than the __dev* marking removals, there's nothing major here,
some firmware loading updates and other minor things in the driver
core.
All of these have (much to Stephen's annoyance), been in linux-next
for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fixed up trivial conflicts in drivers/gpio/gpio-{em,stmpe}.c due to gpio
update.
* tag 'driver-core-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (93 commits)
modpost.c: Stop checking __dev* section mismatches
init.h: Remove __dev* sections from the kernel
acpi: remove use of __devinit
PCI: Remove __dev* markings
PCI: Always build setup-bus when PCI is enabled
PCI: Move pci_uevent into pci-driver.c
PCI: Remove CONFIG_HOTPLUG ifdefs
unicore32/PCI: Remove CONFIG_HOTPLUG ifdefs
sh/PCI: Remove CONFIG_HOTPLUG ifdefs
powerpc/PCI: Remove CONFIG_HOTPLUG ifdefs
mips/PCI: Remove CONFIG_HOTPLUG ifdefs
microblaze/PCI: Remove CONFIG_HOTPLUG ifdefs
dma: remove use of __devinit
dma: remove use of __devexit_p
firewire: remove use of __devinitdata
firewire: remove use of __devinit
leds: remove use of __devexit
leds: remove use of __devinit
leds: remove use of __devexit_p
mmc: remove use of __devexit
...
* Introduction of device PM QoS flags.
* ACPI device power management update allowing subsystems other than
PCI to use it more easily.
* ACPI device enumeration rework allowing additional kinds of devices
to be enumerated via ACPI. From Mika Westerberg, Adrian Hunter,
Mathias Nyman, Andy Shevchenko, and Rafael J. Wysocki.
* ACPICA update to version 20121018 from Bob Moore and Lv Zheng.
* ACPI memory hotplug update from Wen Congyang and Yasuaki Ishimatsu.
* Introduction of acpi_handle_<level>() messaging macros and ACPI-based CPU
hot-remove support from Toshi Kani.
* ACPI EC updates from Feng Tang.
* cpufreq updates from Viresh Kumar, Fabio Baltieri and others.
* cpuidle changes to quickly notice governor prediction failure from
Youquan Song.
* Support for using multiple cpuidle drivers at the same time and cpuidle
cleanups from Daniel Lezcano.
* devfreq updates from Nishanth Menon and others.
* cpupower update from Thomas Renninger.
* Fixes and small cleanups all over the place.
--
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=6OEP
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-for-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
- Introduction of device PM QoS flags.
- ACPI device power management update allowing subsystems other than
PCI to use it more easily.
- ACPI device enumeration rework allowing additional kinds of devices
to be enumerated via ACPI. From Mika Westerberg, Adrian Hunter,
Mathias Nyman, Andy Shevchenko, and Rafael J. Wysocki.
- ACPICA update to version 20121018 from Bob Moore and Lv Zheng.
- ACPI memory hotplug update from Wen Congyang and Yasuaki Ishimatsu.
- Introduction of acpi_handle_<level>() messaging macros and ACPI-based
CPU hot-remove support from Toshi Kani.
- ACPI EC updates from Feng Tang.
- cpufreq updates from Viresh Kumar, Fabio Baltieri and others.
- cpuidle changes to quickly notice governor prediction failure from
Youquan Song.
- Support for using multiple cpuidle drivers at the same time and
cpuidle cleanups from Daniel Lezcano.
- devfreq updates from Nishanth Menon and others.
- cpupower update from Thomas Renninger.
- Fixes and small cleanups all over the place.
* tag 'pm+acpi-for-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (196 commits)
mmc: sdhci-acpi: enable runtime-pm for device HID INT33C6
ACPI: add Haswell LPSS devices to acpi_platform_device_ids list
ACPI: add documentation about ACPI 5 enumeration
pnpacpi: fix incorrect TEST_ALPHA() test
ACPI / PM: Fix header of acpi_dev_pm_detach() in acpi.h
ACPI / video: ignore BIOS initial backlight value for HP Folio 13-2000
ACPI : do not use Lid and Sleep button for S5 wakeup
ACPI / PNP: Do not crash due to stale pointer use during system resume
ACPI / video: Add "Asus UL30VT" to ACPI video detect blacklist
ACPI: do acpisleep dmi check when CONFIG_ACPI_SLEEP is set
spi / ACPI: add ACPI enumeration support
gpio / ACPI: add ACPI support
PM / devfreq: remove compiler error with module governors (2)
cpupower: IvyBridge (0x3a and 0x3e models) support
cpupower: Provide -c param for cpupower monitor to schedule process on all cores
cpupower tools: Fix warning and a bug with the cpu package count
cpupower tools: Fix malloc of cpu_info structure
cpupower tools: Fix issues with sysfs_topology_read_file
cpupower tools: Fix minor warnings
cpupower tools: Update .gitignore for files created in the debug directories
...
This commit changes the CMA early initialization code to use phys_addr_t
for representing physical addresses instead of unsigned long.
Without this change, among other things, dma_declare_contiguous() simply
discards any memory regions whose address is not representable as unsigned
long.
This is a problem on 32-bit PAE machines where unsigned long is 32-bit
but physical address space is larger.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Avoid doing a linear scan of the entire register map for each read() of
the debugfs register dump by recording the offsets where valid registers
exist when we first read the registers file. This assumes the set of
valid registers never changes, if this is not the case invalidation of
the cache will be required.
This could be further improved for large blocks of contiguous registers
by calculating the register we will read from within the block - currently
we do a linear scan of the block. An rbtree may also be worthwhile.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In preparation for doing things a bit more quickly than a linear scan
factor out the initial seek from the debugfs register dump.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If count is less than the size of a register then we may hit integer
wraparound when trying to move backwards to check if we're still in
the buffer. Instead move the position forwards to check if it's still
in the buffer, we are unlikely to be able to allocate a buffer
sufficiently big to overflow here.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
* pm-qos:
PM / QoS: Handle device PM QoS flags while removing constraints
PM / QoS: Resume device before exposing/hiding PM QoS flags
PM / QoS: Document request manipulation requirement for flags
PM / QoS: Fix a free error in the dev_pm_qos_constraints_destroy()
PM / QoS: Fix the return value of dev_pm_qos_update_request()
PM / ACPI: Take device PM QoS flags into account
PM / Domains: Check device PM QoS flags in pm_genpd_poweroff()
PM / QoS: Make it possible to expose PM QoS device flags to user space
PM / QoS: Introduce PM QoS device flags support
PM / QoS: Prepare struct dev_pm_qos_request for more request types
PM / QoS: Introduce request and constraint data types for PM QoS flags
PM / QoS: Prepare device structure for adding more constraint types
Remove conditional code based on CONFIG_HOTPLUG being false. It's
always on now in preparation of it going away as an option.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* linus/master: (1428 commits)
futex: avoid wake_futex() for a PI futex_q
watchdog: using u64 in get_sample_period()
writeback: put unused inodes to LRU after writeback completion
mm: vmscan: check for fatal signals iff the process was throttled
Revert "mm: remove __GFP_NO_KSWAPD"
proc: check vma->vm_file before dereferencing
UAPI: strip the _UAPI prefix from header guards during header installation
include/linux/bug.h: fix sparse warning related to BUILD_BUG_ON_INVALID
Linux 3.7-rc7
powerpc/eeh: Do not invalidate PE properly
ALSA: hda - Fix build without CONFIG_PM
of/address: sparc: Declare of_iomap as an extern function for sparc again
PM / QoS: fix wrong error-checking condition
bnx2x: remove redundant warning log
vxlan: fix command usage in its doc
8139cp: revert "set ring address before enabling receiver"
MPI: Fix compilation on MIPS with GCC 4.4 and newer
MIPS: Fix crash that occurs when function tracing is enabled
MIPS: Merge overlapping bootmem ranges
jbd: Fix lock ordering bug in journal_unmap_buffer()
...
Drivers usually expect that the devices they are supposed to handle
will be operational when their .probe() routines are called, but that
need not be the case on some ACPI-based systems with ACPI-based
device enumeration where the BIOSes don't put devices into D0 by
default. To work around this problem it is sufficient to change
bus type .probe() routines to ensure that devices will be powered
on before the drivers' .probe() routines run (and their .remove()
and .shutdown() routines accordingly).
Modify platform_drv_probe() to run acpi_dev_pm_attach() for devices
whose ACPI handles are present, so that ACPI power management is used
to change their power states. Analogously, modify
platform_drv_remove() and platform_drv_shutdown() to call
acpi_dev_pm_detach() for those devices, so that they are not subject
to ACPI PM any more.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
dma_common_get_sgtable() function doesn't depend on
ARCH_HAS_DMA_DECLARE_COHERENT_MEMORY, so it must not be compiled
conditionally.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
syscore_shutdown uses initcall_debug to control the debug info output.
It’s a good programming. But device_shutdown doesn’t. The patch changes
device_shutdown to follow the style.
Signed-off-by: Yanmin Zhang <yanmin_zhang@linux.intel.com>
Signed-off-by: ShuoX Liu <shuox.liu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PM QoS flags have to be handled by dev_pm_qos_constraints_destroy()
in the same way as PM QoS resume latency constraints. That is, if
they have been exposed to user space, they have to be hidden from it
and the list of flags requests has to be flushed before destroying
the device's PM QoS object. Make that happen.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
dev_pm_qos_add_request() can return 0, 1, or a negative error code,
therefore the correct error test is "if (error < 0)." Checking just for
non-zero return code leads to erroneous setting of the req->dev pointer
to NULL, which then leads to a repeated call to
dev_pm_qos_add_ancestor_request() in st1232_ts_irq_handler(). This in turn
leads to an Oops, when the I2C host adapter is unloaded and reloaded again
because of the inconsistent state of its QoS request list.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many of the regmap enabled drivers implementing one or more of the
readable, writeable, volatile and precious methods use the same code
pattern:
return ((reg >= X && reg <= Y) || (reg >= W && reg <= Z) || ...)
Switch to a data driven approach, using tables to describe
readable/writeable/volatile and precious registers ranges instead.
The table based check can still be overridden by passing the usual function
pointers via struct regmap_config.
Signed-off-by: Davide Ciminaghi <ciminaghi@gnudd.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The current platform device creation and registration code in
acpi_create_platform_device() is quite convoluted. This function
takes an ACPI device node as an argument and eventually calls
platform_device_register_resndata() to create and register a
platform device object on the basis of the information contained
in that code. However, it doesn't associate the new platform
device with the ACPI node directly, but instead it relies on
acpi_platform_notify(), called from within device_add(), to find
that ACPI node again with the help of acpi_platform_find_device()
and acpi_platform_match() and then attach the new platform device
to it. This causes an additional ACPI namespace walk to happen and
is clearly suboptimal.
Use the observation that it is now possible to initialize the ACPI
handle of a device before calling device_add() for it to make this
code more straightforward. Namely, add a new field to struct
platform_device_info allowing us to pass the ACPI handle of interest
to platform_device_register_full(), which will then use it to
initialize the new device's ACPI handle before registering it.
This will cause acpi_platform_notify() to use the ACPI handle from
the device structure directly instead of using the .find_device()
routine provided by the device's bus type. In consequence,
acpi_platform_bus, acpi_platform_find_device(), and
acpi_platform_match() are not necessary any more, so remove them.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Probably due to copy&paste, some stuff was simply forgotten.
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We hit an hang issue when removing a mmc device on Medfield Android phone by sysfs interface.
device_pm_remove will call pm_runtime_remove which would disable
runtime PM of the device. After that pm_runtime_get* or
pm_runtime_put* will be ignored. So if we disable the runtime PM
before device really be removed, drivers' _remove callback may
access HW even pm_runtime_get* fails. That is bad.
Consider below call sequence when removing a device:
device_del => device_pm_remove
=> class_intf->remove_dev(dev, class_intf) => pm_runtime_get_sync/put_sync
=> bus_remove_device => device_release_driver => pm_runtime_get_sync/put_sync
remove_dev might call pm_runtime_get_sync/put_sync.
Then, generic device_release_driver also calls pm_runtime_get_sync/put_sync.
Since device_del => device_pm_remove firstly, later _get_sync wouldn't really wake up the device.
I git log -p to find the patch which moves the calling to device_pm_remove ahead.
It's below patch:
commit 775b64d2b6
Author: Rafael J. Wysocki <rjw@sisk.pl>
Date: Sat Jan 12 20:40:46 2008 +0100
PM: Acquire device locks on suspend
This patch reorganizes the way suspend and resume notifications are
sent to drivers. The major changes are that now the PM core acquires
every device semaphore before calling the methods, and calls to
device_add() during suspends will fail, while calls to device_del()
during suspends will block.
It also provides a way to safely remove a suspended device with the
help of the PM core, by using the device_pm_schedule_removal() callback
introduced specifically for this purpose, and updates two drivers (msr
and cpuid) that need to use it.
As device_pm_schedule_removal is deleted by another patch, we need also revert other parts of the patch,
i.e. move the calling of device_pm_remove after the calling to bus_remove_device.
Signed-off-by: LongX Zhang <longx.zhang@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When PM runtime is enabled in DaVinci and the machine migrates to
common clk framework, the clk_enable() gets called without
clk_prepare(). This patch is to fix this issue so that PM run
time can inter work with common clk framework.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The callback function of call_rcu() just calls a kfree(), so we
can use kfree_rcu() instead of call_rcu() + callback function.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently the opp_find* functions return -ENODEV when:
a) it cant find a device (e.g. request for an OPP search on device
which was not registered)
b) When it cant find a match for the search strategy used
This makes life a little in-efficient for users such as devfreq
to make reasonable judgement before switching search strategies.
So, standardize the return results as following:
-EINVAL for bad pointer parameters
-ENODEV when device cannot be found
-ERANGE when search fails
This has the following benefit for devfreq implementation:
The search fails when an unregistered device pointer is provided.
This is a trigger to change the search direction and search for
a better fit, however, if we cannot differentiate between a valid
search range failure Vs an unregistered device, second search goes
through the same fail return condition. This can be avoided by
appropriate handling of error return code.
With this change, we also fix devfreq for the improved search
strategy with updated error code.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Export the OPP functions for use by driver modules.
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Kevin Hilman <khilman@ti.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
[nm@ti.com: expansion of functions exported]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
synchronize_rcu() blocks the caller of opp_enable/disbale
for a complete grace period. This blocking duration prevents
any intensive use of the functions. Replace synchronize_rcu()
by call_rcu() which will call our function for freeing the old
opp element.
The duration of opp_enable() and opp_disable() will be no more
dependant of the grace period.
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
With ACPI 5 it is now possible to enumerate traditional SoC
peripherals, like serial bus controllers and slave devices behind
them. These devices are typically based on IP-blocks used in many
existing SoC platforms and platform drivers for them may already
be present in the kernel tree.
To make driver "porting" more straightforward, add ACPI support to
the platform bus type. Instead of writing ACPI "glue" drivers for
the existing platform drivers, register the platform bus type with
ACPI to create platform device objects for the drivers and bind the
corresponding ACPI handles to those platform devices.
This should allow us to reuse the existing platform drivers for the
devices in question with the minimum amount of modifications.
This changeset is based on Mika Westerberg's and Mathias Nyman's
work.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch documents the firmware cache mechanism so that
users of request_firmware() know that it can be called
safely inside device's suspend and resume callback, and
the device's firmware needn't be cached any more by individual
driver itself to deal with firmware loss during system resume.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch introduces one module parameter of 'path' in firmware_class
to support customizing firmware image search path, so that people can
use its own firmware path if the default built-in paths can't meet their
demand[1], and the typical usage is passing the below from kernel command
parameter when 'firmware_class' is built in kernel:
firmware_class.path=$CUSTOMIZED_PATH
[1], https://lkml.org/lkml/2012/10/11/337
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The comment above fw_file_size() suggests it is noinline for stack size
reasons. Use noinline_for_stack to make this more clear.
Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Acked-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is one race that both request_firmware() with the same
firmware name.
The race scenerio is as below:
CPU1 CPU2
request_firmware() -->
_request_firmware_load() return err another request_firmware() is coming -->
_request_firmware_cleanup is called --> _request_firmware_prepare -->
release_firmware ---> fw_lookup_and_allocate_buf -->
spin_lock(&fwc->lock)
... __fw_lookup_buf() return true
fw_free_buf() will be called --> ...
kref_put -->
decrease the refcount to 0
kref_get(&tmp->ref) ==> it will trigger warning
due to refcount == 0
__fw_free_buf() -->
... spin_unlock(&fwc->lock)
spin_lock(&fwc->lock)
list_del(&buf->list)
spin_unlock(&fwc->lock)
kfree(buf)
After that, the freed buf will be used.
The key race is decreasing refcount to 0 and list_del is not protected together by
fwc->lock, and it is possible another thread try to get it between refcount==0
and list_del.
Fix it here to protect it together.
Acked-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: liu chuansheng <chuansheng.liu@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a race as below when calling request_firmware():
CPU1 CPU2
write 0 > loading
mutex_lock(&fw_lock)
...
set_bit FW_STATUS_DONE class_timeout is coming
set_bit FW_STATUS_ABORT
complete_all &completion
...
mutex_unlock(&fw_lock)
In this time, the bit FW_STATUS_DONE and FW_STATUS_ABORT are set,
and request_firmware() will return failure due to condition in
_request_firmware_load():
if (!buf->size || test_bit(FW_STATUS_ABORT, &buf->status))
retval = -ENOENT;
But from the above scenerio, it should be a successful requesting.
So we need judge if the bit FW_STATUS_DONE is already set before
calling fw_load_abort() in timeout function.
As Ming's proposal, we need change the timer into sched_work to
benefit from using &fw_lock mutex also.
Signed-off-by: liu chuansheng <chuansheng.liu@intel.com>
Acked-by: Ming Lei <ming.lei@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since dev_pm_qos_add_request(), dev_pm_qos_update_request() and
dev_pm_qos_remove_request() for PM QoS flags should not be invoked
when device in RPM_SUSPENDED, add pm_runtime_get_sync() and pm_runtime_put()
around these functions in dev_pm_qos_expose_flags() and
dev_pm_qos_hide_flags().
[rjw: Modified the subject and changelog to better reflect the code
changes made.]
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull sparc fixes from David Miller:
"Several build/bug fixes for sparc, including:
1) Configuring a mix of static vs. modular sparc64 crypto modules
didn't work, remove an ill-conceived attempt to only have to build
the device match table for these drivers once to fix the problem.
Reported by Meelis Roos.
2) Make the montgomery multiple/square and mpmul instructions actually
usable in 32-bit tasks. Essentially this involves providing 32-bit
userspace with a way to use a 64-bit stack when it needs to.
3) Our sparc64 atomic backoffs don't yield cpu strands properly on
Niagara chips. Use pause instruction when available to achieve
this, otherwise use a benign instruction we know blocks the strand
for some time.
4) Wire up kcmp
5) Fix the build of various drivers by removing the unnecessary
blocking of OF_GPIO when SPARC.
6) Fix unintended regression wherein of_address_to_resource stopped
being provided. Fix from Andreas Larsson.
7) Fix NULL dereference in leon_handle_ext_irq(), also from Andreas
Larsson."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Fix build with mix of modular vs. non-modular crypto drivers.
sparc: Support atomic64_dec_if_positive properly.
of/address: sparc: Declare of_address_to_resource() as an extern function for sparc again
sparc32, leon: Check for existent irq_map entry in leon_handle_ext_irq
sparc: Add sparc support for platform_get_irq()
sparc: Allow OF_GPIO on sparc.
qlogicpti: Fix build warning.
sparc: Wire up sys_kcmp.
sparc64: Improvde documentation and readability of atomic backoff code.
sparc64: Use pause instruction when available.
sparc64: Fix cpu strand yielding.
sparc64: Make montmul/montsqr/mpmul usable in 32-bit threads.
This adds sparc support for platform_get_irq that in the normal case use
platform_get_resource() to get an irq. This standard approach fails for sparc as
there are no resources of type IORESOURCE_IRQ for irqs for sparc.
Cross platform drivers can then use this standard platform function and work on
sparc instead of having to have a special case for sparc.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In fact, the callers of dev_pm_qos_add_request(),
dev_pm_qos_update_request() and dev_pm_qos_remove_request() for
requests of type DEV_PM_QOS_FLAGS need to ensure that the target
device is not RPM_SUSPENDED before using any of these functions (or
be prepared for the new PM QoS flags to take effect after the device
has been resumed). Document this in their kerneldoc comments.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Free a wrong point to struct dev_pm_qos->latency which suppose to
be the point to struct dev_pm_qos. The patch is to fix the issue.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
dev_<level> calls take less code than dev_printk(KERN_<LEVEL>
and reducing object size is good.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e39473d (PM / QoS: Make it possible to expose PM QoS device
flags to user space) introduced __dev_pm_qos_update_request() to be
called internally by dev_pm_qos_update_request(), but forgot to make
the latter actually use the return value of the former. Fix this
mistake.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This seems to be the most common way of reporting register numbers, it's
certainly what we do for trace.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This pulls in the various driver core changes that were in 3.7-rc3 into the
driver-core-next branch.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Fix for a memory leak in acpi_bind_one() from Jesper Juhl.
* Fix for an error code path memory leak in pm_genpd_attach_cpuidle()
from Jonghwan Choi.
* Fix for smp_processor_id() usage in preemptible code in powernow-k8 from
Andreas Herrmann.
* Fix for a suspend-related memory leak in cpufreq stats from Xiaobing Tu.
* Freezer fix for failure to clear PF_NOFREEZE along with PF_KTHREAD
in flush_old_exec() from Oleg Nesterov.
* acpi_processor_notify() fix from Alan Cox.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=8Tcc
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-for-3.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael J Wysocki:
- Fix for a memory leak in acpi_bind_one() from Jesper Juhl.
- Fix for an error code path memory leak in pm_genpd_attach_cpuidle()
from Jonghwan Choi.
- Fix for smp_processor_id() usage in preemptible code in powernow-k8
from Andreas Herrmann.
- Fix for a suspend-related memory leak in cpufreq stats from Xiaobing
Tu.
- Freezer fix for failure to clear PF_NOFREEZE along with PF_KTHREAD in
flush_old_exec() from Oleg Nesterov.
- acpi_processor_notify() fix from Alan Cox.
* tag 'pm+acpi-for-3.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: missing break
freezer: exec should clear PF_NOFREEZE along with PF_KTHREAD
Fix memory leak in cpufreq stats.
cpufreq / powernow-k8: Remove usage of smp_processor_id() in preemptible code
PM / Domains: Fix memory leak on error path in pm_genpd_attach_cpuidle
ACPI: Fix memory leak in acpi_bind_one()
Here are a number of firmware core fixes for 3.7, and some other minor fixes.
And some documentation updates thrown in for good measure.
All have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlCKwkIACgkQMUfUDdst+ynzUgCfQDwxUw1PVqQyWy7SakpsjFJJ
8kwAoITyjppn39v1WuZbg0+FZ6JpocyY
=2mDG
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg Kroah-Hartman:
"Here are a number of firmware core fixes for 3.7, and some other minor
fixes. And some documentation updates thrown in for good measure.
All have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'driver-core-3.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
Documentation:Chinese translation of Documentation/arm64/memory.txt
Documentation:Chinese translation of Documentation/arm64/booting.txt
Documentation:Chinese translation of Documentation/IRQ.txt
firmware loader: document kernel direct loading
sysfs: sysfs_pathname/sysfs_add_one: Use strlcat() instead of strcat()
dynamic_debug: Remove unnecessary __used
firmware loader: sync firmware cache by async_synchronize_full_domain
firmware loader: let direct loading back on 'firmware_buf'
firmware loader: fix one reqeust_firmware race
firmware loader: cancel uncache work before caching firmware
them together into a mca_config struct. This keeps them tightly and
neatly packed together instead of spilled all over the place.
Then, convert those which are used as booleans into real booleans and
save some space.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJQioVNAAoJEBLB8Bhh3lVKH/MP/2tGCqEdB7uxIgAKy/2wkG9G
G3ad7ggSCPA7YygWsgKFicHNp511LqjQ45Bs9WGjMn2Fnkq6TCAqNO9CDB1cfX6W
N0uYMQKkE6Ccx8wU29ilDHh5hU0vOYDd3EOk7e4Ox64C1i4PjO1QnS2TvphJTkto
riy3yWvshLYUZdciWHJcT18KuGK3JIetyVo6hanWb3uIXudQLsfE5O077N+rWUOg
7kw23iwlWN2AudOZD5JKUAsKztOfXZ1KS2WiVgTfw+g5o4lBtbYmQ5II4LJfVCgU
y/f5Ux80Q71XRsV8WSfakMfVKRN0pmuEJ2zKHUrN9yySVLV/neJZoWIP0z/uyr3f
GvOErf4PDRpNu43oobm32+BIMb2IUlhc5sIOV25bMYdbBewS/R5I4KLE51+BCJIY
/XC+C4rL60i5W62A+Y88xpnlwI62b+QC20PkVJYnk4vLkIE5UliOy5jhACI6iJm4
0Bwz4zXFhlzBNQItOsA6AUwYOHYhjVzqKYQMC05fVGLNxEDCx3DjRavy/ICnSAgu
G9aRBHtg1JPoXziMtIZkCWsiTKCzz5Vxugdo7WxyXFqXrlK/IxydVuRU2DuiJSXo
2+7n3M1G4uLj+6s/JaEj6RZTWpKFBo4VH8dUivfrTyoZsCg0hiVSYI2W/Rsc7ZCo
kCsn+H79xW6RBbxtrEqe
=EOHq
-----END PGP SIGNATURE-----
Merge tag 'mca_cfg' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras into x86/ras
Pull x86 RAS changes from Borislav Petkov:
"Rework all config variables used throughout the MCA code and collect
them together into a mca_config struct. This keeps them tightly and
neatly packed together instead of spilled all over the place.
Then, convert those which are used as booleans into real booleans and
save some space."
Signed-off-by: Ingo Molnar <mingo@kernel.org>
... which, analogous to DEVICE_INT_ATTR provides functionality to
set/clear bools. Its purpose is to be used where values need to be used
as booleans in configuration context.
Next patch uses this.
Signed-off-by: Borislav Petkov <bp@alien8.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Tony Luck <tony.luck@intel.com>
Pull CMA and DMA-mapping fixes from Marek Szyprowski:
"This consists mainly of a set of one-liner fixes and cleanups for a
few minor issues identified in both Contiguous Memory Allocator code
and ARM DMA-mapping subsystem."
* 'fixes_for_linus' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
ARM: mm: Remove unused arm_vmregion priv field
ARM: dma-mapping: fix build warning in __dma_alloc()
ARM: dma-mapping: support debug_dma_mapping_error
mm: cma: alloc_contig_range: return early for err path
drivers: cma: Fix wrong CMA selected region size default value
drivers: dma-coherent: Fix typo in dma_mmap_from_coherent documentation
drivers: dma-contiguous: Don't redefine SZ_1M
This config item has not carried much meaning for a while now and is
almost always enabled by default. As agreed during the Linux kernel
summit, remove it.
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
val_bytes is of 'size_t', so it should be printed as '%zu'.
Fixes the following build warning on x86:
drivers/base/regmap/regmap.c:872:4: warning: format '%d' expects argument of type 'int', but argument 5 has type 'size_t' [-Wformat]
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Make the generic PM domains pm_genpd_poweroff() function take
device PM QoS flags into account when deciding whether or not to
remove power from the domain.
After this change the routine will return -EBUSY without executing
the domain's .power_off() callback if there is at least one PM QoS
flags request for at least one device in the domain and at least of
those request has at least one of the NO_POWER_OFF and REMOTE_WAKEUP
flags set.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: mark gross <markgross@thegnar.org>
Define two device PM QoS flags, PM_QOS_FLAG_NO_POWER_OFF
and PM_QOS_FLAG_REMOTE_WAKEUP, and introduce routines
dev_pm_qos_expose_flags() and dev_pm_qos_hide_flags() allowing the
caller to expose those two flags to user space or to hide them
from it, respectively.
After the flags have been exposed, user space will see two
additional sysfs attributes, pm_qos_no_power_off and
pm_qos_remote_wakeup, under the device's /sys/devices/.../power/
directory. Then, writing 1 to one of them will update the
PM QoS flags request owned by user space so that the corresponding
flag is requested to be set. In turn, writing 0 to one of them
will cause the corresponding flag in the user space's request to
be cleared (however, the owners of the other PM QoS flags requests
for the same device may still request the flag to be set and it
may be effectively set even if user space doesn't request that).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Acked-by: mark gross <markgross@thegnar.org>
Kconfig lists CMA_SIZE_SEL_ABSOLUTE as the default value fo the CMA
selected region size, but that option isn't available in the defined
choices. Set the default to CMA_SIZE_SEL_MBYTES instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
The function documentation incorrectly references dma_release_coherent.
Fix it. Don't mention a specific function name as dma_mmap_from_coherent
as multiple callers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Use the definition from linux/sizes.h instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Modify the device PM QoS core code to support PM QoS flags requests.
First, add a new field of type struct pm_qos_flags called "flags"
to struct dev_pm_qos for representing the list of PM QoS flags
requests for the given device. Accordingly, add a new "type" field
to struct dev_pm_qos_request (along with an enum for representing
request types) and a new member called "flr" to its data union for
representig flags requests.
Second, modify dev_pm_qos_add_request(), dev_pm_qos_update_request(),
the internal routine apply_constraint() used by them and their
existing callers to cover flags requests as well as latency
requests. In particular, dev_pm_qos_add_request() gets a new
argument called "type" for specifying the type of a request to be
added.
Finally, introduce two routines, __dev_pm_qos_flags() and
dev_pm_qos_flags(), allowing their callers to check which PM QoS
flags have been requested for the given device (the caller is
supposed to pass the mask of flags to check as the routine's
second argument and examine its return value for the result).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: mark gross <markgross@thegnar.org>
The subsequent patches will use struct dev_pm_qos_request for
representing both latency requests and flags requests. To make that
easier, put the node member of struct dev_pm_qos_request (under the
name "pnode") into a union called "data" that will represent the
request's value and list node depending on its type.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: mark gross <markgross@thegnar.org>
Currently struct dev_pm_info contains only one PM QoS constraints
pointer reserved for latency requirements. Since one more device
constraints type (i.e. flags) will be necessary, introduce a new
structure, struct dev_pm_qos, that eventually will contain all of
the available device PM QoS constraints and replace the "constraints"
pointer in struct dev_pm_info with a pointer to the new structure
called "qos".
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
If pm_genpd_attach_cpudidle failed we leak memory stored in 'cpu_data'.
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
async.c has provided synchronization mechanism on async_schedule_*,
so use async_synchronize_full_domain to sync caching firmware instead
of reinventing the wheel.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Firstly 'firmware_buf' is introduced to make all loading requests
to share one firmware kernel buffer, so firmware_buf should
be used in direct loading for saving memory and speedup firmware
loading.
Secondly, the commit below
abb139e75c2cdbb955e840d6331cb5863e409d0e(firmware:teach
the kernel to load firmware files directly from the filesystem)
introduces direct loading for fixing udev regression, but it
bypasses the firmware cache meachnism, so this patch enables
caching firmware for direct loading case since it is still needed
to solve drivers' dependency during system resume.
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several loading requests may be pending on one same
firmware buf, and this patch moves fw_map_pages_buf()
before complete_all(&fw_buf->completion) and let all
requests see the mapped 'buf->data' once the loading
is completed.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Under 'Opportunistic sleep' situation, system sleep might be
triggered very frequently, so the uncahce work may not be completed
before caching firmware during next suspend.
This patch cancels the uncache work before caching firmware to
fix the problem above.
Also this patch optimizes the cacheing firmware mechanism a bit by
only storing one firmware cache entry for one firmware image.
So if the firmware is still cached during suspend, it doesn't need
to be loaded from user space any more.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The regmap_mmio and regmap_irq depend on regmap core, if not select,
we may not compile regmap core and meet compiling errors as follows
if REGMAP_MMIO is selected by client drivers:
drivers/mfd/syscon.c:94:15: error: variable 'syscon_regmap_config' has initializer but incomplete type
drivers/mfd/syscon.c:95:2: error: unknown field 'reg_bits' specified in initializer
drivers/mfd/syscon.c:95:2: warning: excess elements in struct initializer [enabled by default]
drivers/mfd/syscon.c:95:2: warning: (near initialization for 'syscon_regmap_config') [enabled by default]
drivers/mfd/syscon.c:96:2: error: unknown field 'val_bits' specified in initializer
drivers/mfd/syscon.c:96:2: warning: excess elements in struct initializer [enabled by default]
drivers/mfd/syscon.c:96:2: warning: (near initialization for 'syscon_regmap_config') [enabled by default]
drivers/mfd/syscon.c:97:2: error: unknown field 'reg_stride' specified in initializer
drivers/mfd/syscon.c:97:2: warning: excess elements in struct initializer [enabled by default]
drivers/mfd/syscon.c:97:2: warning: (near initialization for 'syscon_regmap_config') [enabled by default]
drivers/mfd/syscon.c: In function 'syscon_probe':
drivers/mfd/syscon.c:124:2: error: invalid use of undefined type 'struct regmap_config'
drivers/mfd/syscon.c:125:2: error: implicit declaration of function 'devm_regmap_init_mmio' [-Werror=implicit-function-declaration]
drivers/mfd/syscon.c:125:17: warning: assignment makes pointer from integer without a cast [enabled by default]
cc1: some warnings being treated as errors
drivers/mfd/Kconfig:
config MFD_SYSCON
bool "System Controller Register R/W Based on Regmap"
depends on OF
select REGMAP_MMIO
help
Select this option to enable accessing system control registers
via regmap.
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It is sometimes convenient for a regmap user to override the standard
regmap lock/unlock functions with custom functions.
For instance this can be useful in case an already existing spinlock
or mutex has to be used for locking a set of registers instead of the
internal regmap spinlock/mutex.
Note that the fast_io field of struct regmap_bus is ignored in case
custom locking functions are used.
Signed-off-by: Davide Ciminaghi <ciminaghi@gnudd.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Building regmap.o triggers this GCC warning:
drivers/base/regmap/regmap.c: In function ‘regmap_raw_read’:
drivers/base/regmap/regmap.c:1172:6: warning: ‘ret’ may be used uninitialized in this function [-Wmaybe-uninitialized]
Long story short: Jakub Jelinek pointed out that there is a type
mismatch between 'num' in regmap_volatile_range() and 'val_count' in
regmap_raw_read(). And indeed, converting 'num' to the type of
'val_count' (ie, size_t) makes this warning go away.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If a block write covers a paged memory region and crosses a window
boundary then rather than failing the write split the transfer up
into multiple writes, making the whole process more transparent for
drivers.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The range code was written to check for return codes less than zero as
errors but throughout the rest of the API return codes not equal to zero
are errors. Change all these checks to match the house style.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Dimitris Papastamos