The current number of RX buffers queued is 32, which is too small under
heavy load. That number is doubled.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Changes in the gain-control mechanism will require some changes in the header.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The present code fails to set the linked state when an interface is
added.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The initial USB driver did not use some register save locations in the
private data storage. To save some memory, a union was used to overlay these
variables with USB I/O components. In an update of the gain-control code,
these register save locations are now needed for USB drivers.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vendor driver rtl8188C_8192C_8192D_usb_linux_v3.4.2_3727.20120404 introduced
new firmware for these chips. The code try for the new file, and fall back to
the original firmware if the new file is not available.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This driver has a watchdog timer that attempts to reconnect when beacon frames
are not seen for 6 seconds. This patch disables that reconnect whenever the
device has never been connected.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In rt2800_init_rfcsr_5592(), there's no need to write RF register 3 twice.
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When routine rtl_is_special_data() is called with false as its last argument,
and the returned value is not tested, the call is essentially an extended
no-op. Accordingly, these calls may be removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The wcn36xx_err macro should not end in a semicolon as
there are 2 consecutive semicolons in the preprocessed
output.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Eugene Krasnikov <k.eugene.e@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable the beacon changed using BSS_CHANGED_BEACON. This is
especially useful for mesh mode.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Under heavy load, the relatively small number of RX queue entries are
completely filled. With an increase from 16 to 32 entries, this condition
rarely happens.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
freq_reg_info() expects KHz and not MHz, fix this. In
this case we'll now be getting the no-ir flags cleared
on channels for any channel when the country IE trusts
that channel.
@@
struct ieee80211_channel *ch;
struct wiphy *wiphy;
const struct ieee80211_reg_rule *rule;
@@
-rule = freq_reg_info(wiphy, ch->center_freq);
+rule = freq_reg_info(wiphy, MHZ_TO_KHZ(ch->center_freq));
Generated-by: Coccinelle SmPL
Cc: Julia Lawall <julia.lawall@lip6.fr>
Cc: Peter Senna Tschudin <peter.senna@gmail.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Mihir Shete <smihir@qti.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
freq_reg_info() expects KHz and not MHz, fix this. In
this case we'll now be getting the no-ir flags cleared
on channels for any channel when the country IE trusts
that channel.
@@
struct ieee80211_channel *ch;
struct wiphy *wiphy;
const struct ieee80211_reg_rule *rule;
@@
-rule = freq_reg_info(wiphy, ch->center_freq);
+rule = freq_reg_info(wiphy, MHZ_TO_KHZ(ch->center_freq));
Generated-by: Coccinelle SmPL
Cc: Julia Lawall <julia.lawall@lip6.fr>
Cc: Peter Senna Tschudin <peter.senna@gmail.com>
Cc: Seth Forshee <seth.forshee@canonical.com>
Cc: Arend van Spriel <arend@broadcom.com>
Reported-by: Mihir Shete <smihir@qti.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The cw1200_irq_handler() function expects the hwbus lock to be held when
it is called. On the SDIO platform, this lock is implemented in terms
of sdio_claim_host/sdio_release_host.
This trivial patch makes it explicit that we are performing the hwbus
lock rather than something SDIO-specific.
Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The reason that a scan failed for some reason (typically bad
parameters) should be logged even when debugging is turned off.
Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can mess logs if user space try to open device again and again if
RFKILL switch is on. Do not print message and return ERFKILL error
instead to indicate where the problem is.
Note that iwl4965 handle this problem differently, it allows to open
device when radio is disabled.
Reported-by: Dietmar Rudolph <dietmar@crlf.de>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
the original code used goto out if kzalloc fails,but the out include kfree,
so return -ENOMEM if kzalloc fails.
Signed-off-by: Jing Wang <windsdaemon@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since firmware loading became async it is possible that if_sdio_finish_power_of
is called with only one remaining runtime_pm reference, so it isn't safe
to call pm_runtime_put_noidle. We must call pm_runtime_put().
Diagnosed-by: "Dr. H. Nikolaus Schaller" <hns@goldelico.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mirror the latest MediaTek/Ralink driver with respect to RT5390 RF register
programming. The PCI and USB devices use different init values.
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1) Move common code out of switch case handling
2) Return from the function if number of bytes left in response buffer
are less than tlv size
3) Pass pg_tlv_hdr directly instead of txp_cfg to mwifiex_get_power_level()
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update bbp register initialization for RT53xx chips to match with the
latest MediaTek/Ralink driver.
Based on: NICInitRT5390BbpRegisters()
From: DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5390.c
Signed-off-by: Kevin Lo <kevlo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adding the debugfs file <debugfs_mnt>/brcmfmac/<devid>/chipinfo
which contains the chip number and revision.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The dhd.h file contained a number of definitions that are
related to events received from the firmware. Those are
processed and dispatched in the driver by fweh. Hence the
definitions are moved to its include file.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Removing WLC_PHY_TYPE and some BRCMF_E_.* definitions as these
are not used in the driver sources.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The BCDC protocol layer is using a mix of naming of CDC, BDC and
BCDC. Use the name BCDC consistenly over all functions, defines
and variables. This patch does not change code functionality.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the command codes to the firmware interface module as
that makes a bit more sense.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware control interface is provided by fwil source file, but
a number of structures used to communicate with the firmware still
resided in dhd.h. The patch moves them to fwil_types.h.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In bcmsdh.c the functions brcmf_sdio_probe() and brcmf_sdio_remove()
were exported, but that is not needed. The functions are linked into
the driver module, which is the only one needing to call these.
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Knowing the firmware version is pretty useful information when
looking at issues. It is retrieved during initialization so
store it in driver data structure to fill the ethtool driver
info when requested.
Reviewed-by: Hante Meuleman <meuleman@brodcom.com>
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BCDC is the default protocol layer and being called directly. This
patch installs the functions for this layer dynamically. This allows
new protocols to be added and selected dynamically depending on the
hw capabilties. As currently only BCDC is supported this is always
the installed protocol.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ioctl() entry points were empty except for handling SIOC_ETHTOOL
but that has been obsoleted in favor of struct ethtool_ops. Cleaning
up removing the ioctl() handlers.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The SDIO part of the brcmfmac driver uses a static define BRCMF_SDALIGN
to align buffers used for SDIO transfers. This patch replaces it by
using alignment derived from the platform specific data.
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The alignment values were being determined for each transmit
and receive depending on platform data. Instead determine
these once during the probe.
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
dhd_proto.h was cleaned up and prototypes were moved to dhd.h.
dhd_proto.h was removed. This is a step in cleaning and
restucturing protocol layer.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
dhd_cdc is renamed to bcdc. This is a step in cleaning and
restructuring protocol layer. This is done so new protocols can
be added in the future. This step only renames the source files.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
[arend@broadcom.com: use 'git mv' to do the rename]
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
New WiFi full dongle supports receiving chained packets in one command
through the SDIO bus. This patch adds the support on the host side to
send chained packets.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add firmware/nvram file name for bcm4339 so fmac can actually be functional with
the chip.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When CONFIG_BRCMDBG is not set we get the following build issue:
CC [M] drivers/net/wireless/brcm80211/brcmfmac/fwsignal.o
drivers/net/wireless/brcm80211/brcmfmac/fwsignal.c:
In function ‘brcmf_fws_hdrpush’:
drivers/net/wireless/brcm80211/brcmfmac/fwsignal.c:852:18:
error: ‘BRCMF_FWS_TYPE_SEQ_LEN’ undeclared
The define BRCMF_FWS_TYPE_SEQ_LEN was introduced by:
commit 6918f38e4ed4e0493a90a4331e0033bdfc806e00
Author: Hante Meuleman <meuleman@broadcom.com>
Date: Wed Oct 23 14:58:51 2013 +0200
brcmfmac: Update fwsignal to fix out of order tx.
Unfortunately, it was put in conditional part of the source
file under #ifdef DEBUG.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "eb9c174 brcmfmac: determine host controller related
variables during probe" was not implemented correctly as the
information is already needed in brcmf_sdbrcm_probe(). This patch
moves it to brcmf_sdioh_attach() instead.
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The SDPCM header can be traced, but it used a fixed header size. With
txglom feature the SDPCM header will have additional 8 bytes of hardware
extension header so SDIO core can properly handle the txglom packet.
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The brcmsmac relies BCMA functionality to access the device. This
patch selects CONFIG_BCMA when CONFIG_BCMA_POSSIBLE is set. This
way the user does not need to be select BCMA to make the brcmsmac
driver show up in his menuconfig.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The SleepCSR register is accessed to wakeup the device from the
host side. Depending on the state of the device this may take
multiple attempts. The failed attempt are not real failures so
reduce the log level specifically for this register. The calling
function will scream when the multiple attempts all failed.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Moving the call to netif_start_queue() after brcmf_cfg80211_up() is
completed successful. If not return -EIO instead of -1 as that results
in 'Operation not permitted' which can put user on wrong track.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The bus-specific interface allowed a list of dongle commands to be
provided to the common driver part. However, upcoming functionality
requires a more dynamic behaviour. Hence the list is replaced
by a new callback function so the bus-specific driver part can
implement this behaviour.
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The common driver needs the packet overhead for the bus in order
to reserve headroom for sk_buffs. For the SDIO driver this depends
on firmware features so it is not possible to provide it in the
brcmf_attach() call.
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When using fwsignal it is possible that tx packets get delivered out
of order. This patch fixes that by reordering suppressed packets and
tracking generation bit and sequence number per packet.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is missing for AR9300, AR9580 and AR9340.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Baseband updates
* Remove ar9340Common_rx_gain_table_1p0 since it is a duplicate.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The initvals for AR9462 v2.1 are very similar to v2.0.
Identify duplicate arrays and reuse the values from v2.0
to reduce module size.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The initialization arrays for v1.1 AR9565
are mostly the same as v1.0/v1.0.1 except for
radio_postamble.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since IQ calibration is done as part of AGC calibration for
AR9485 and above, remove the seperate IQ calibration code.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The CHANNEL_HT flag is insignificant for fast channel change conditions,
since it does not affect any important part of the hardware reset /
channel setup.
Scanning usually runs with HT disabled, so this change will slightly
improve scan time on many chipsets.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A cold reset can be triggered because of DMA stop issues, and this leads
to TSF being cleared on all chipsets. To properly deal with this, always
save the TSF.
Additionally, account for the time it takes to do the actual chip reset,
which can be quite significant. On AR9344 it takes around 4.5 ms.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of checking the queues in a loop with hardcoded sleep times
inbetween, use a wait queue to trigger queue checks after the tx
processing tasklet has run.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the software has processed all packets, checking the hardware queue
is unnecessary.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When operating in client mode, the short period of time between scanning
and associating is often enough to put the hardware through several
FULL-SLEEP <-> AWAKE transitions, each wakeup requiring a reset to fully
recover the hardware.
This is completely unnecessary and can easily be avoided by deferring
the switch to full sleep.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since calibration data reuse is not enabled in
SoC chips, simplify the IQ calibration code.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CL calibration is applicable for all chips and the
enable/disable knob comes via the INI file. For PCOEM
chips, the calibration data is reused when Fast Channel Change
is used. Caldata reuse is not enabled for SoC chips, so remove
the CL post processing code.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TX IQ calibration is always enabled for SoC chips.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RTT is enabled only for AR9462 and MCI for AR9462/AR9565.
Also, manual peak calibration is not done for any of the
SoC chips.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Though there is some overlap between the calibration mechanisms
of PC-OEM cards and SoC chip families, dumping both of them
into a single function makes things hard to understand.
ar9003_hw_init_cal() is unreadable with chip-specific segments
scattered around. To make the logic understandable, use
different functions for client cards and SoC chips. Some
code is duplicated, but in the long run, it makes the code
more maintanable.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SC_OP_INVALID is zero so the test is always false. We're supposed to be
testing the lowest bit instead.
Fixes: 89f927af7f ('ath9k: add TX99 support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CUS227, which is an AR9340 based card used in Qualcomm's
Allplay platforms requires a custom TX gain array, based
on the index 7. Add suport for this.
Cc: Michael Larson <mlarson@qce.qualcomm.com>
Cc: Stephen Collmeyer <scollmey@qce.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This HW config option is always set to true and is not needed.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the WoW code to wow.c and compile it conditionally
based on CONFIG_ATH9K_WOW.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The HW routines to set various WoW registers are present
in wow.c. For some reason, it has been compiled as part
of the main ath9k.ko module all this time, when it should
really be part of ath9k_hw.ko. This patch renames the file to
ar9003_wow.ko and adds it to ath9k_hw.ko.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use CONFIG_ATH9K_TX99 to properly enclose the tx99 code
and make sure that it is not compiled as part of the driver
when it is not selected. Move the tx99 code to a new file tx99.c
and also add ATH9K_DEBUGFS as a dependency in Kconfig.
This reduces the module size on platforms like OpenWrt where
ATH9K_DEBUGFS is selected, but TX99 might be disabled.
Cc: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Building brcmfmac for sparc64 gave the following warning:
CC [M] drivers/net/wireless/brcm80211/brcmfmac/bcmsdh_sdmmc.o
bcmsdh_sdmmc.c: In function 'brcmf_sdioh_request_byte':
bcmsdh_sdmmc.c:89:6: warning: 'err_ret' may be used uninitialized
in this function [-Wuninitialized]
Inspecting the code it indeed had a path of execution in
which the return value was used uninitialized. This patch
fixes that code path.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If kmalloc fails wcn36xx_smd_rsp_process will attempt to dereference
a NULL pointer. There might be a better error recovery then just
printing an error, but printing an error message is better then the
current behaviour.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Code in ath9k_hw_set_clockrate function indicates that ah->curchan
(and thus chan local variable) may be NULL. If that is indeed the
case, IS_CHAN_HT40(chan) check has to be performed only in branch
where chan is not NULL. Moving the code under already existing
if condition fixes this issue.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The EEPROM parameter to determine whether the bias
strength values for XLNA have to be applied is part
of the miscConfiguration field and not featureEnable.
Cc: stable@vger.kernel.org
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bit 5 in the miscConfiguration field of the base EEPROM
header denotes whether QuickDrop is enabled or not. Fix
the incorrect usage of BIT(1) and also make sure that
this is done only for the required chips.
Cc: stable@vger.kernel.org
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
FW 10.1 seems to require the default key index to
be updated to point to group key after it is
installed. Otherwise Txed frames are corrupted.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The channel switch notification should be sent under the
wdev/sdata-lock, preferably in the same moment as the channel change
happens, to avoid races by other callers (e.g. start/stop_ap).
This also adds the previously missing sdata_lock protection in
csa_finalize_work.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change cfg80211 and mac80211 to use cfg80211_mgmt_tx_params
struct to aggregate parameters for mgmt_tx functions.
This makes the functions' signatures less clumsy and allows
less painful parameters extension.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
[fix all other drivers]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The beacon timers really shouldn't use any clock that is
subject to adjustments from userspace, particularly not
CLOCK_REALTIME. Use CLOCK_MONOTONIC_RAW instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Too much of tx info was being cleared. This caused
issues in some setups with tx frame status
reporting.
This should fix some cases of stations not being
able to associate to ath10k AP.
Reported-By: Matti Laakso <malaakso@elisanet.fi>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This can be useful for testing and debugging.
This introduces new ath10k_pci module parameter
`irq_mode`. By default it is 0, meaning automatic
irq mode (MSI-X as long as both target HW and host
platform supports it). The parameter works on a
best effort basis.
kvalo: fix typo "ayto"
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It's possible for FW to panic during early boot.
The patch re-introduces support to detect and
print those crashes.
This introduces an additional irq handler that is
set for the duration of early boot and shutdown.
The handler is then overriden with regular
handlers upon hif start().
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Preparation for code re-use. Also use ioread/write
wrappers.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It's impossible to rely on disable_irq() and/or CE
interrupt masking with legacy shared interrupts.
Other devices sharing the same irq line may assert
it while ath10k is doing something that requires
no interrupts.
Irq handlers are now registered after all
preparations are complete so spurious/foreign
interrupts won't do any harm. The handlers are
unregistered when no interrupts are required (i.e.
during driver teardown).
This also removes the ability to receive FW early
indication (since interrupts are not registered
until early boot is complete). This is not mission
critical (it's more of a hint that early boot
failed due to unexpected FW crash) and will be
re-added in a follow up patch.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The function did a couple of things: it allocated
CE completions, registered CE callbacks and
enabled CE interrupts through HW registers.
This cannot be so. Split the function into one
that allocates CE completions and the other one
that starts off CE operation.
This is required for future legacy shared
interrupt handling.
This also fixes possible memory leak if post rx
failed.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It's not really necessary for interrupts to be
used for BMI. BMI already assumes there's only one
caller at a time and it works directly with CE.
Make BMI poll for CE completions instead of
waiting for interrupts. This makes disabling
interrupts during early boot possible.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Hardware waits until host signals whether it has
chosen MSI(-X) or shared legacy interrupts. It is
not required for the driver to register interrupt
handlers immediately.
This patch prepares the pci irq code for more
changes.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k assumed all interrupts were directed to it.
This isn't the case for legacy shared interrupts.
ath10k consumed interrupts for other devices.
Check device irq status and return IRQ_NONE when
appropriate.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If the next seqno returned by the firmware is 0, we return an error
(-16) in the iwl_mvm_get_last_nonqos_seq() function. This is because
we return an integer and don't use any casting when calculating the
last seqno from the one we received. Fix this by using a cast to u16
when doing the calculation, so we return 0xfff0, as we should.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In an open BSS, after suspend/resume, we don't set the last seqno
because the iwl_mvm_setup_connection_keep() returns too early. This
happens because the check to see if we have any keys was returning
immediately, without setting seqno and seqno_valid. Fix this.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Larry Finger