Commit Graph

364 Commits

Author SHA1 Message Date
Sujith Manoharan 4a878b9f89 ath9k: Initialize baseband for DFS channels
Certain baseband registers require different values
to be programmed when operating in a DFS channel to
ensure that radar detection works correctly. This
is required for AR9300, AR9340 and AR9580.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-12-09 15:37:56 -05:00
Sujith Manoharan c6fc7e64e1 ath9k: Remove pcieSerDesWrite
This HW config option is always set to true and is not needed.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-12-02 14:24:55 -05:00
Sujith Manoharan e60001e716 ath9k: Use CONFIG_ATH9K_WOW
Move the WoW code to wow.c and compile it conditionally
based on CONFIG_ATH9K_WOW.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-12-02 14:24:54 -05:00
Sujith Manoharan 2d22c7dded ath9k: Use correct PCIE initvals for AR9485
Currently, the PLL is turned off for AR9485 when
switching to a low power state, but AR9485 has an issue
where the card will become unresponsive if left idle
for a long time without any traffic. To fix this,
force the PLL to always be on using a different initval
array, ar9485_1_1_pll_on_cdr_on_clkreq_disable_L1.

This is done for most of the AR9485 based cards
like HB125, WB225 etc. but certain models require the
feature to be turned off. Identify such cards and use
default values for them.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-11-11 14:47:45 -05:00
Luis R. Rodriguez 89f927af7f ath9k: add TX99 support
TX99 support enables Specific Absorption Rate (SAR) testing.
SAR is the unit of measurement for the amount of radio frequency(RF)
absorbed by the body when using a wireless device. The RF
exposure limits used are expressed in the terms of SAR, which is a
measure of the electric and magnetic field strength and power density
for transmitters operating at frequencies from 300 kHz to 100 GHz.

Regulatory bodies around the world require that wireless device
be evaluated to meet the RF exposure limits set forth in the
governmental SAR regulations.

In the examples below, for more bit rate options see the iw TX bitrate
setting documentation:

http://wireless.kernel.org/en/users/Documentation/iw#Modifying_transmit_bitrates

Example usage:

iw phy phy0 interface add moni0 type monitor
ip link set dev moni0 up

iw dev moni0 set channel 36 HT40+
iw set bitrates mcs-5 4

echo 10 > /sys/kernel/debug/ieee80211/phy0/ath9k/tx99_power
echo 1  > /sys/kernel/debug/ieee80211/phy0/ath9k/tx99

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-18 14:06:56 -04:00
Felix Fietkau e4744ec786 ath9k_hw: remove references to hw->conf
Accessing it to get the current operating channel is racy and in the way
of further channel handling related changes

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-14 13:39:59 -04:00
Felix Fietkau 6b21fd2027 ath9k_hw: simplify channel flags
There was some duplication between channelFlags and chanmode, as well as
a lot of redundant checks based on the combinations of flags.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-14 13:39:58 -04:00
Felix Fietkau 81c507a8b0 ath9k_hw: remove IS_CHAN_OFDM()
The hardware is always configured with OFDM support enabled

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-14 13:39:58 -04:00
Felix Fietkau 1a5e63265f ath9k_hw: remove IS_CHAN_B()
Hardware 802.11b-only mode isn't supported by the driver (the device is
configured for 802.11n/g instead). Simplify the code by removing checks
for it.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-14 13:39:58 -04:00
Felix Fietkau 8896934c16 ath9k_hw: remove direct accesses to channel mode flags
Use wrappers where available. Simplifies code and helps with further
improvements to the channel data structure

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-14 13:39:58 -04:00
Sujith Manoharan 3001f0d00b ath9k: Fix PeakDetect calibration for AR9462
Since HW PeakDetect calibration is turned on for AR9462,
various conditions have to be handled in the driver:

* Enable agc_cal when loading RTT fails.
* Disable SW PeakDetect calibration when RTT calibration is not enabled.
* Keep SW PeakDetect calibration result in driver.
* Update RTT table according to the saved value.
* Write RTT back after modifying SW RTT table.
* Enable local mode for PeakDetect calibration and restore values.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-09-26 15:13:47 -04:00
Sujith Manoharan 4b9b42bfe0 ath9k: Use bitops for calibration flags
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-09-26 15:13:47 -04:00
Sujith Manoharan 1e516ca7c9 ath9k: Handle abnormal NAV in AP mode
Beacon transmission would get stuck if the NAV is
an invalid value for some reason. Check and correct
the NAV value in the HW when this happens.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-09-26 15:13:46 -04:00
Zefir Kurtisi 5e88ba6228 ath9k: replace snprintf() with scnprintf()
Whenever the return value of snprintf() is used to calculate
remaining buffer-space, we wanted to use sncprintf() instead.

Indentation is adapted where possible. Some lines exceed the
line width limit, either they did it already before, or
since they can not be broken reasonably well.

Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-09-26 15:13:35 -04:00
Sujith Manoharan f96bd2ad22 ath9k: Add support for AR9565 v1.0.1 LNA diversity
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-09-26 15:13:28 -04:00
Sujith Manoharan b380a43b52 ath9k: Fix ASPM for AR9462
If the L1 entrance latency is not calibrated properly
in the EEPROM in WB222 boards, there could be problems
in connectivity. Check and correct the calibrated value
if it doesn't match the optimal value for WB222, 4us.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-08-26 14:09:05 -04:00
Sujith Manoharan e083a42ef6 ath9k: Add antenna diversity tweak for CUS198
This improves RX diversity and performance for AR9485.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-08-22 14:30:29 -04:00
Sujith Manoharan 36e8825e65 ath9k: Fix build failure
Make sure that CONFIG_ATH9K_BTCOEX_SUPPORT is used for
the WLAN/BT RX diversity hooks.

Reported by the kernel build testing backend.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-08-09 15:57:53 -04:00
Sujith Manoharan 31fd216db9 ath9k: Set SWCOM value for CUS198
CUS198/CUS230 cards require a custom value to be
programmed into the SWCOM register. Assign this during
init time.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-08-05 14:52:44 -04:00
Sujith Manoharan 7bdea96a1b ath9k: Remove "shared_chain_lnadiv"
This variable is redundant since we can use
common->bt_ant_diversity to determine if diversity
has to be enabled/disabled.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-08-05 14:52:44 -04:00
Sujith Manoharan d8d7744b72 ath9k: Rename ath9k_hw_antctrl_shared_chain_lnadiv
Use "ath9k_hw_set_bt_ant_diversity" instead.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-08-05 14:52:42 -04:00
Sujith Manoharan 3f2da95517 ath9k: Add a HW capability for WLAN/BT RX diversity
Make use of this capability to restrict the usage of the
debugfs file and modparam using which this feature can
be enabled.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-08-05 14:52:42 -04:00
Sujith Manoharan 81dc75b584 ath9k: Add a HW flag for FCC
Fast Channel Change across 2G/5G bands is supported
only by AR9462 and AR9565. Add a HW capability field
to indicate this.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-07-22 16:54:42 -04:00
Sujith Manoharan c177fabe20 ath9k: Program initvals for CUS217
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-18 14:46:48 -04:00
Sujith Manoharan 51dbd0a897 ath9k: Add support for 5G-XLNA/AR9462
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-18 14:46:45 -04:00
Sujith Manoharan 9b60b64bfe ath9k: Add custom parameters for CUS198
CUS198 is a card based on AR9485. There are differences
between the base reference design HB125 and CUS198.
Identify such cards based on the PCI subsystem IDs and
set HW parameters appropriately.

Addresses this bug - https://bugzilla.kernel.org/show_bug.cgi?id=49201

Cc: jkp@iki.fi
Cc: gfmichaud@gmail.com
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-14 13:37:16 -04:00
Sujith Manoharan c24bd3620c ath9k: Do not maintain ANI state per-channel
ANI state can be maintained globally instead of per-channel.
This reduces memory usage and since default values are used
during a scan run, per-channel state is not required.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-03 15:55:48 -04:00
Sujith Manoharan e323300d97 ath9k: Simplify ANI initialization
The check "enable_ani" is not required since it is always
set to true and the logic for disabling/enabling ANI via
debugfs is done at a higher layer.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-03 15:55:47 -04:00
Sujith Manoharan 846e438f5f ath9k: Enable WoW only for AR9462
The only card with which WoW has been tested and verified is
AR9462. Do not enable it for all cards since WoW is really quirky
and needs to be tested properly with each chip.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-03 15:55:46 -04:00
Felix Fietkau a043dfb90e ath9k_hw: make various ar5416/ar91xx rf banks const
Banks 0-3,7 are neither modified at run time, nor SREV dependent.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-04-10 14:10:32 -04:00
Felix Fietkau 37c62fecbf ath9k_hw: clean up RF Bank6 handling on AR5416/AR91xx
There are two sets of initvals for this RF bank, one with TPC support and
one without.
The TPC one always gets used, so remove the other one to avoid confusion.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-04-10 14:10:32 -04:00
Sujith Manoharan fcb9a3de1e ath9k_hw: Remove CHANNEL_CW_INT
This flag is used for indicating channel interference and
we currently do nothing with it, so remove it.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-03-06 16:28:52 -05:00
John W. Linville 9ebea3829f Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
Conflicts:
	drivers/net/wireless/ath/ath9k/main.c
	drivers/net/wireless/iwlwifi/dvm/tx.c
2013-01-28 13:54:03 -05:00
Felix Fietkau f5ffe23aa0 ath9k_hw: remove ath9k_hw_ani_setup and its variables
They are no longer needed for ANI functionality

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-01-22 16:05:31 -05:00
Felix Fietkau 0166b4beec ath9k_hw: make the initval parameter to ath9k_hw_write_array const
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-01-22 16:03:22 -05:00
Felix Fietkau 6aaacd8615 ath9k_hw: fix RF bank initialization
ar900*_init_mode_regs needs to be called before RF banks are allocated,
otherwise the storage size of RF banks isn't known. This patch fixes
a memory overrun that can show up as a crash on unloading the module.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-01-22 15:58:48 -05:00
Felix Fietkau 4a8f199508 ath9k_hw: fix calibration issues on chainmask that don't include chain 0
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-01-22 14:33:43 -05:00
Simon Wunderlich e93d083f42 ath9k: add spectral scan feature
Adds the spectral scan feature for ath9k. AR92xx and AR93xx chips
are supported for now. The spectral scan is triggered by configuring
a mode through a debugfs control file. Samples can be gathered via
another relay debugfs file.

Essentially, to try it out:

echo chanscan > /sys/kernel/debug/ieee80211/phy0/ath9k/spectral_scan_ctl
iw dev wlan0 scan
cat /sys/kernel/debug/ieee80211/phy0/ath9k/spectral_scan0 > samples
echo disable > /sys/kernel/debug/ieee80211/phy0/ath9k/spectral_scan_ctl

This feature is still experimental.

The special "chanscan" mode is used to perform spectral scan while
mac80211 is scanning for channels. To allow this,
sw_scan_start/complete() ops have been added.

The patch contains code snippets and information from Zefir Kurtisi and
information provided by Adrian Chadd and Felix Fietkau.

Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-01-09 14:37:12 -05:00
Sujith Manoharan 96da6fdd5a ath9k_hw: Use helper routines to simplify ar9003_hw_init_cal()
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-01-09 14:37:10 -05:00
Sujith Manoharan 1a6e5d7c96 ath9k_hw: Remove TEMP_COMP_CAL
This is not enabled for any chip and is unused.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-01-07 15:17:00 -05:00
Felix Fietkau c1b976d2fc ath9k_hw: use the devres API for allocations
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-01-07 15:16:51 -05:00
Gabor Juhos ab5c4f71d8 ath9k: allow to load EEPROM content via firmware API
The calibration data for devices w/o a separate
EEPROM chip can be specified via the 'eeprom_data'
field of 'ath9k_platform_data'. The 'eeprom_data'
is usually filled from board specific setup
functions. It is easy if the EEPROM data is mapped
to the memory, but it can be complicated if it is
stored elsewhere.

The patch adds support for loading of the EEPROM
data via the firmware API to avoid this limitation.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-12-10 15:49:57 -05:00
Sujith Manoharan 0f21ee8d9c ath9k_hw: Add HW cap for PAPRD
Add a HW capability to indicate whether PAPRD is enabled
for the card, since PAPRD could be enabled in the EEPROM, but
disabled in the driver. This makes things clearer.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-12-10 15:49:50 -05:00
Sujith Manoharan 36d2943ba7 ath9k_hw: Various trivial fixes for PAPRD
* Remove unneeded memset.

  All the values in the PAPRD gain table are filled, so there
  is no need to zero out the arrays.

* Use GFP_KERNEL in ar9003_paprd_create_curve

  This is called from the PAPRD work, so the atomic variant
  is not needed.

* Change return type of ar9003_paprd_setup_gain_table

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-12-10 15:49:48 -05:00
Sujith Manoharan 57527f8d4d ath9k_hw: Program filter coefficients correctly
2484 Mhz (Japan) usage requires filter coefficients to
be programmed in the CCK TX FIR registers. This is required
for AR9331, AR9485 and AR9462. Fix this and also remove
a few useless macros and a duplicate variable.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-11-16 14:29:11 -05:00
Sujith Manoharan b126b02796 ath9k: Remove unused workaround
The workaround for ASPM/L0s is needed only for AR9485 1.0,
which was never sold and is not supported by ath9k.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-11-16 14:11:14 -05:00
Rajkumar Manoharan 77d8483728 ath9k: fill channel mode in caldata
It is useful to have channel mode in caldata to find out
whether operaing channel is in HT40/20 when we are currently
on offchannel. It will be used by BTCOEX to enable/disable
concurrent tx mechanism later.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-10-29 15:18:53 -04:00
Rajkumar Manoharan 424749c75d ath9k: perform ANI cycle in idle state
As of now the ANI cycle is executed only when the chip is awake.
On idle state case, the station wakes up from network sleep for
beacon reception. Since most of the time, ANI cycle is not syncing
with beacon wakeup, ANI cycle is ignored. Approx 5 mins once, the
calibration is performed. This could affect the connection stability
when the station is idle for long. Even though the OFDM and CCK phy
error rates are too high, ANI is unable to tune its immunity level
as quick enough due to rare execution.

Here the experiment shows that OFDM and CCK levels are at default
even on higher phy error rate.

listenTime=44 OFDM:3 errs=121977/s CCK:2 errs=440818/s ofdm_turn=1

This change ensures that ANI calibration will be exectued atleast
once for every 10 seconds. The below result shows improvements and
immunity levels are adopted quick enough.

listenTime=557 OFDM:4 errs=752/s CCK:4 errs=125/s ofdm_turn=0

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-10-19 16:16:14 -04:00
Felix Fietkau ceb26a6013 ath9k: improve suspend/resume reliability
Ensure that drv_start() always returns true, as a failing hw start usually
eventually leads to crashes when there's still a station entry present.
Call a power-on reset after a resume and after a hw reset failure to bring
the hardware back to life again.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-10-05 16:26:17 -04:00
David S. Miller a248afdc1b Merge branch 'for-davem' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next
John W. Linville says:

====================
Here is another batch of updates intended for 3.7...

Highlights include an hci_connect re-write in Bluetooth, HCI/LLC
layer separation in NFC, removal of the raw pn544 NFC driver, NFC LLCP
raw sockets support, improved IBSS auth frame handling in mac80211,
full-MAC AP mode notification support in mac80211, a lot of attention
paid to brcmfmac, and the usual level of updates to iwlwifi, ath9k,
mwifiex, and rt2x00, and various other updates.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2012-09-30 02:30:16 -04:00