It is possible for the cmd11 interrupt to fire and delete the
cmd11_timer before the cmd11_timer was actually setup. Let's fix this
race by adding a few spinlocks. Note that the race wasn't seen in
practice without adding some printk statements, but it still seems
wise to fix.
Fixes: 5c935165da ("mmc: dw_mmc: Add a timeout for sending CMD11")
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If we get an unexpected cmd11 timeout we shouldn't actually treat it
as a timeout (not that we really expect to get an unexpected cmd11
timeout, but still).
Fixes: 5c935165da ("mmc: dw_mmc: Add a timeout for sending CMD11")
Reported-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Although the cmd11 interrupt should come within 2ms, that's a very
short time. Let's increase the timeout to be really sure that we
don't get an accidnetal timeout. One case in particular this is
useful is if you've got a serial console and printk in just the right
places. Under that scenario I've seen delays of up to 130ms before
the interrupt fired.
CMD11 is only sent during card insertion, so this extra timeout
shouldn't be terrible.
Fixes: 5c935165da ("mmc: dw_mmc: Add a timeout for sending CMD11")
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The dw_mmc driver changes to make the IO accesors endian agnostic did not
take into account the fifo accesses do not need to be swapped. To fix this
add a mmci_fifo_read/write wrapper to allow these to be passed through the
IO without being swapped.
Since these are now specific functions, it would be easier just to store
the pointer to the fifo registers in the host block instead of the offset
to them. So change the host->data_offset to host->fifo_reg (which also
means we catch all the places this is read or written).
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The dw_mmc driver does not take into account the processor may be in
big endian when writing the descriptors. Change the descriptors for
the 32bit IDMA to use __le32 and ensure they are suitably swapped
before writing.
Note, this has not been tested as the socfpga driver does not try to
use idma.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If dw_mci_init_slot() returns that we got a probe deferral then it may
leave slot->mmc as NULL. That will cause dw_mci_enable_cd() to crash
when it calls mmc_gpio_get_cd().
Fix this by moving the call of dw_mci_enable_cd() until we're sure
that we're good. Note that if we have more than one slot and one
defers (but the others don't) things won't work so well. ...but
that's not a new thing and everyone has already agreed that multislot
support ought to be removed from dw_mmc eventually anyway since it is
unused, untested, and you can see several bugs like this by inspecting
the code.
Fixes: bcafaf5470f0 ("mmc: dw_mmc: Only enable CD after setup and only if needed")
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the Designware databook's description of the "Voltage Switch Normal
Scenario" it instructs us to set a timer and fail the voltage change
if we don't see the voltage change interrupt within 2ms. Let's
implement that. Without implementing this I have often been able to
reproduce a hang while trying to send CMD11 on an rk3288-based board
while constantly ejecting and inserting UHS cards.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It's unlikely that this is really needed on any single-slot systems
where we disable card detects until the end of probe, but it still
seems safer to check to make sure that a slot has been initted before
we try to dereference it to find the SDIO interrupt mask.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We really don't want to get a card detect interrupt during probe time
since it can confuse things. Let's disable the card detect interrupt
until we're in a really good place: the end of probe. Let's also
simply avoid enabling the card detect interrupt if it's not used.
It appears that (at least on rk3288) when vqmmc is turned on it can
cause a bogus "card detect" interrupt. That meant that we were
getting a predictable card detect interrupt while we were in
mmc_add_host(). On the version of the kernel I'm working with at
least (3.14), this is not a great time to get a card detect interrupt
since I think that we don't grab all the needed locks in
mmc_add_host() and children. I put stack dumps in dw_mci_setup_bus()
and found that I could see two distinct stack crawls that looked like:
Caller one:
* dw_mci_setup_bus
* dw_mci_set_ios
* mmc_power_up
* mmc_start_host
* mmc_add_host
Caller two:
* dw_mci_setup_bus
* dw_mci_set_ios
* mmc_set_chip_select
* mmc_go_idle
* mmc_rescan
* process_one_work
* worker_thread
* kthread
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We've seen problems on some WiFi modules where we seem to send a CMD53
(which requires the data lines) while the module is asserting busy.
We shouldn't do that.
The Designware Databook says that before issuing a new data transfer
command we should check for busy, so that's what we'll do.
We'll leverage the existing dw_mmc knowledge about whether it should
wait for the previous command to finish to know whether we should
check for busy before sending the command. This means we won't end up
incorrectly waiting for things like CMD52 (SDIO) or CMD13 (SD) which
don't use the data line.
Note that this also has the advantage of making sure that we don't
change the clock while the card is busy, too.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We should give dw_mmc a good reset after we apply power. On some
boards vqmmc may actually be connected to the IP block in the SoC so
it's good to reset after power comes in.
Without this we sometimes see failures enumerating cards on rk3288.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It appears that we can confuse things if we try to turn on the MMC
clock when the power is off. Adjust is so that we turn the clock on
(using dw_mci_setup_bus) after power is all the way on and we turn the
clock off before the power goes off.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The STOP command can terminate a data transfer between a memory card and
mmc controller.
As show in Synopsys DesignWare Cores Mobile Storage Host Databook:
Data timeout and Data end-bit error will terminate further data transfer
by mmc controller. So we should not send abort command to terminate a
data transfer again if we got DRTO and EBE interrupt.
After this patch, all mmc_test cases can pass on RK3288-Pink2 board.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Implements HS400 mode support for exynos host driver.
This also include some updates as new mode is added.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
[Alim: addressed review comments]
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If we power up vqmmc in MMC_POWER_ON then we end up turning it on
before mmc_power_up() sets the signal voltage. That's not so great
since we might be powering it up at the wrong voltage.
Note that this is how Yuvaraj originally coded things up in
<https://patchwork.kernel.org/patch/4401231/> but he changed it on my
suggestion. Apparently I was wrong.
Reported-by: Alexandru M Stan <amstan@chromium.org>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of having a local hack taking care of sending the tuning
command and as well to verify the response pattern, let's convert to
the common mmc_send_tuning() API.
This change affects the Exynos variant, since it's the only one which
support the dw_mmc's ->execute_tuning() callback.
It's seems like dw_mmc internal logic expects failed data transfers to
be ended using a stop command. Let the tuning requests also fall into
this category, since there are data transfer involved.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Even though 1MB is reserved for descriptor table in IDMAC,
the dw_mmc host driver is allowed to receive only maximum
128KB block length in one request. This is caused by setting
improper max_blk_count. It needs to be e adjusted so that
descriptor table is used fully. It is found that the performance
is improved with the increased the max_blk_count.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We're running into cases where our enabling of the SDIO interrupt in
dw_mmc doesn't actually take effect. Specifically, adding patch like
this:
+++ b/drivers/mmc/host/dw_mmc.c
@@ -1076,6 +1076,9 @@ static void dw_mci_enable_sdio_irq(struct mmc_host *mmc, int enb)
mci_writel(host, INTMASK,
(int_mask | SDMMC_INT_SDIO(slot->id)));
+ int_mask = mci_readl(host, INTMASK);
+ if (!(int_mask & SDMMC_INT_SDIO(slot->id)))
+ dev_err(&mmc->class_dev, "failed to enable sdio irq\n");
} else {
...actually triggers the error message. That's because the
dw_mci_enable_sdio_irq() unsafely does a read-modify-write of the
INTMASK register.
We can't just use the standard host->lock since that lock is not irq
safe and mmc_signal_sdio_irq() (called from interrupt context) calls
dw_mci_enable_sdio_irq(). Add a new irq-safe lock to protect INTMASK.
An alternate solution to this is to punt mmc_signal_sdio_irq() to the
tasklet and then protect INTMASK modifications by the standard host
lock. This seemed like a bit more of a high-latency change.
Reported-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the patch (9623b5b mmc: dw_mmc: Disable low power mode if SDIO
interrupts are used) I added code that disabled the low power mode of
dw_mmc when SDIO interrupts are used. That code worked but always
felt a little hacky because we ended up disabling low power as a side
effect of the first enable_sdio_irq() call. That wouldn't be so bad
except that disabling low power involves a complicated process of
writing to the CMD/CMDARG registers and that extra process makes it
difficult to cleanly the read-modify-write race in
dw_mci_enable_sdio_irq() (see future patch in the series).
Change the code to take advantage of the init_card() callback of the
mmc core to do this right at bootup.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit f1d2736c81 (mmc: dw_mmc: control card read threshold) added
dw_mci_ctrl_rd_thld() with an unconditional write to the CDTHRCTL
register at offset 0x100. However before version 240a, the FIFO region
started at 0x100, so the write messes with the FIFO and completely
breaks the driver.
If the version id < 240A, return early from dw_mci_ctl_rd_thld() so as
not to hit this problem.
Fixes: f1d2736c81 (mmc: dw_mmc: control card read threshold)
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: <stable@vger.kernel.org> # v3.13+
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The bit of sdio interrupt is 16 in designware implementation,
but it is 24 on Rockchip SoCs.This patch add sdio_id0 for the
number of slot0 in the SDIO interrupt registers.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Synopsys DW_MMC IP core supports Internal DMA Controller with 64-bit address mode from IP version 2.70a onwards.
Updated the driver to support IDMAC 64-bit addressing mode.
Signed-off-by: Prabu Thangamuthu <prabu.t@synopsys.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The dw_mmc driver had a bunch of code that ran whenever a card was
ejected and inserted. However, this code was old and crufty and
should be removed. Some evidence that it's really not needed:
1. Is is supposed to be legal to use 'cd-gpio' on dw_mmc instead of
using the built-in card detect mechanism. The 'cd-gpio' code
doesn't run any of the crufty old code but yet still works.
2. While looking at this, I realized that my old change (369ac86 mmc:
dw_mmc: don't queue up a card detect at slot startup) actually
castrated the old code a little bit already and nobody noticed.
Specifically "last_detect_state" was left as 0 at bootup. That
means that on the first card removal none of the crufty code ran.
3. I can run "while true; do dd if=/dev/mmcblk1 of=/dev/null; done"
while ejecting and inserting an SD Card and the world doesn't
explode.
If some of the crufty old code is actually needed, we should justify
it and also put it in some place where it will be run even with
"cd-gpio".
Note that in my case I'm using the "cd-gpio" mechanism but for various
reasons the hardware triggers a dw_mmc "card detect" at bootup. That
was actually causing a real bug. The card detect workqueue was
running while the system was trying to enumerate the card. The
"present != slot->last_detect_state" triggered and we were doing all
kinds of crazy stuff and messing up enumeration. The new mechanism of
just asking the core to check the card is much safer and then the
bogus interrupt doesn't hurt.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: alim.akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In (28f92b5 mmc: core: Try other signal levels during power up) we can
see that there are times when it's valid to try several signal
voltages. Don't print an ugly error in the logs when that happens.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We've already got a reset of DMA after it's done. Add one before we
start DMA too. This fixes a data corruption on Rockchip SoCs which
will get bad data when doing a DMA transfer after doing a PIO transfer.
We tested this on an Exynos 5800 with HS200 and didn't notice any
difference in sequential read throughput.
Signed-off-by: Sonny Rao <sonnyrao@chromium.org>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The same tuning block exists in the dw_mmc h.c and sdhci-msm.c
files. Move these into mmc.c so that they can be shared across
drivers.
Reported-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dw_mci_of_find_slot_node() is only used in dw_mci_of_get_slot_quirks()
if CONFIG_OF is defined, thus there is no need to have a !CONFIG_OF
version of it. Fixes the following compile warning with !CONFIG_OF:
CC [M] drivers/mmc/host/dw_mmc.o
drivers/mmc/host/dw_mmc.c:2223:28: warning: ‘dw_mci_of_find_slot_node’ defined but not used [-Wunused-function]
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It's possible that mmc_of_parse() could return errors (possibly in
some future version it might return -EPROBE_DEFER even). Let's pass
those errors back.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For UHS cards we need the ability to switch voltages from 3.3V to
1.8V. Add support to the dw_mmc driver to handle this. Note that
dw_mmc needs a little bit of extra code since the interface needs a
special bit programmed to the CMD register while CMD11 is progressing.
This means adding a few extra states to the state machine to track.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch makes use of mmc_regulator_get_supply() to handle
the vmmc and vqmmc regulators.Also it moves the code handling
the these regulators to dw_mci_set_ios().It turned on the vmmc
and vqmmc during MMC_POWER_UP and MMC_POWER_ON,and turned off
during MMC_POWER_OFF.
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If we happened to get a data error at just the wrong time the dw_mmc
driver could get into a state where it would never complete its
request. That would leave the caller just hanging there.
We fix this two ways and both of the two fixes on their own appear to
fix the problems we've seen:
1. Fix a race in the tasklet where the interrupt setting the data
error happens _just after_ we check for it, then we get a
EVENT_XFER_COMPLETE. We fix this by repeating a bit of code.
2. Fix it so that if we detect that we've got an error in the "data
busy" state and we're not going to do anything else we end the
request and unblock anyone waiting.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@gmail.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch changes the fifo reset code to follow the reset procedure
outlined in the documentation of Synopsys Mobile storage host databook.
Signed-off-by: Sonny Rao <sonnyrao@chromium.org>
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
[sonnyrao: fix compile for !CONFIG_MMC_DW_IDMAC case]
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Data errors are completely expected during tuning. Printing them out
is confusing people looking at the kernel logs. They see things like:
[ 3.613296] dwmmc_exynos 12200000.dwmmc0: data error, status 0x00000088
...and they think something is wrong with their hardware.
Remove the printouts. We'll leave it up to a higher level to report
about errors.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Restore the card-present checking point.
(The following part was removed from commit bf626e5 ("mmc: dw_mmc:
use slot-gpio to handle cd pin")
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Since using the device-tree, didn't use the callback pointer.
So removed the unused callback pointer.
When the set_power callback is used, it should be added in future.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
It's right to check immediately whether host->bus_hz is assigned or not.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
mmc_of_parse() have been already parsed the general capability.
Didn't need to use the local parser.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Replaced UHS_DDR50 with MMC_DDR52. And MMC_CAP_UHS_DDR50
is removed because of non-implementation of UHS signaling.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Core:
- CONFIG_MMC_UNSAFE_RESUME=y is now default behavior.
- DT bindings for SDHCI UHS, eMMC HS200, high-speed DDR, at 1.8/1.2V.
- Add GPIO descriptor based slot-gpio card detect API.
Drivers:
- dw_mmc: Refactor SOCFPGA support as a variant inside dw_mmc-pltfm.c.
- mmci: Support HW busy detection on ux500.
- omap: Support MMC_ERASE.
- omap_hsmmc: Support MMC_PM_KEEP_POWER, MMC_PM_WAKE_SDIO_IRQ, (a)cmd23.
- rtsx: Support pre-req/post-req async.
- sdhci: Add support for Realtek RTS5250 controllers.
- sdhci-acpi: Add support for 80860F16, fix 80860F14/SDIO card detect.
- sdhci-msm: Add new driver for Qualcomm SDHCI chipset support.
- sdhci-pxav3: Add support for Marvell Armada 380 and 385 SoCs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=6S8w
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.15:
Core:
- CONFIG_MMC_UNSAFE_RESUME=y is now default behavior
- DT bindings for SDHCI UHS, eMMC HS200, high-speed DDR, at 1.8/1.2V
- Add GPIO descriptor based slot-gpio card detect API
Drivers:
- dw_mmc: Refactor SOCFPGA support as a variant inside dw_mmc-pltfm.c
- mmci: Support HW busy detection on ux500
- omap: Support MMC_ERASE
- omap_hsmmc: Support MMC_PM_KEEP_POWER, MMC_PM_WAKE_SDIO_IRQ, (a)cmd23
- rtsx: Support pre-req/post-req async
- sdhci: Add support for Realtek RTS5250 controllers
- sdhci-acpi: Add support for 80860F16, fix 80860F14/SDIO card detect
- sdhci-msm: Add new driver for Qualcomm SDHCI chipset support
- sdhci-pxav3: Add support for Marvell Armada 380 and 385 SoCs"
* tag 'mmc-updates-for-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (102 commits)
mmc: sdhci-acpi: Intel SDIO has broken card detect
mmc: sdhci-pxav3: add support for the Armada 38x SDHCI controller
mmc: sdhci-msm: Add platform_execute_tuning implementation
mmc: sdhci-msm: Initial support for Qualcomm chipsets
mmc: sdhci-msm: Qualcomm SDHCI binding documentation
sdhci: only reprogram retuning timer when flag is set
mmc: rename ARCH_BCM to ARCH_BCM_MOBILE
mmc: sdhci: Allow for irq being shared
mmc: sdhci-acpi: Add device id 80860F16
mmc: sdhci-acpi: Fix broken card detect for ACPI HID 80860F14
mmc: slot-gpio: Add GPIO descriptor based CD GPIO API
mmc: slot-gpio: Split out CD IRQ request into a separate function
mmc: slot-gpio: Record GPIO descriptors instead of GPIO numbers
Revert "dts: socfpga: Add support for SD/MMC on the SOCFPGA platform"
mmc: sdhci-spear: use generic card detection gpio support
mmc: sdhci-spear: remove support for power gpio
mmc: sdhci-spear: simplify resource handling
mmc: sdhci-spear: fix platform_data usage
mmc: sdhci-spear: fix error handling paths for DT
mmc: sdhci-bcm-kona: fix build errors when built-in
...
Tejun Heo has made WQ_NON_REENTRANT useless in the dbf2576e37
("workqueue: make all workqueues non-reentrant"). So remove its
usages and definition.
This patch doesn't introduce any behavior changes.
tj: minor description updates.
Signed-off-by: ZhangZhen <zhenzhang.zhang@huawei.com>
Sigend-off-by: Tejun Heo <tj@kernel.org>
Acked-by: James Chapman <jchapman@katalix.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
If mrq->sbc is not NULL but data->stop happens to be NULL,
it will lead to NULL pointer dereferencing. Avoid this by
having a NULL check for data->stop.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>
bf626e5550 ("mmc: dw_mmc: use slot-gpio to handle cd pin") caused
CDETECT to be ignored, since negated return value of mmc_gpio_get_cd(mmc)
can not be checked by IS_ERR_VALUE.
Also, add spin_lock_bh(&host->lock) for atomic access to
DW_MMC_CARD_PRESENT, otherwise sd detect may occasionally fail.
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Reported-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Sachin Kamat <sachin.kamat@linaro.org>
Tested-by: Sachin Kamat <sachin.kamat@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>
Suggested by Jaehoon: Use slot-gpio to handle cd-gpio
Add function dw_mci_of_get_cd_gpio to check "cd-gpios" from dts.
mmc_gpio_request_cd and mmc_gpio_get_cd are used to handle cd pin
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <chris@printf.net>
Suspend and resume of cards are being handled from the protocol layer
and consequently the mmc_suspend|resume_host APIs are deprecated.
This means we can simplify the suspend|resume callbacks by removing the
use of the deprecated APIs.
Cc: Seungwon Jeon <tgih.jun@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
In IDMAC mode EVENT_XFER_COMPLETE is set when RI/TI of last descriptor
is done. So if errors are happened in the middle of data transfers,
'dw_mci_stop_dma' during error handing can be called and eventually
prevents this flag to be set. This results in permanent wait for
EVENT_XFER_COMPLETE in 'dw_mci_tasklet_func'. Therefore, if dma
running is stopped forcibly, EVENT_XFER_COMPLETE should be set.
Reported-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
First, compiling warning along with previous change is removed.
[drivers/mmc/host/dw_mmc.c:1890:7: warning: unused variable 'ctrl']
And with the recommendation in manual, IDMAC software reset is followed
by dma-reset of the CTRL register in order to terminate the transfer.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
There are three resets in CTRL register. FIFO reset is especially used
in several points with the same routine. It could be replaced with one
function and the others may be applied similarly if needed. So,
mci_wait_reset() is modified to allow various bit field of reset.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Main change corresponds to dw_mci_command_complete(). And EBE is
divided into read and write. Some minor changes for code readability.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In error cases, DTO interrupt may or may not be generated depending
on remained data. Stop/Abort command ensures DTO generation for that
situation. Currently if 'stop' field of data is empty, there is no
stop/abort command. So, it could hang waiting DTO. This change
reinforces these cases.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Even if response error is detected in case data command, data transfer
is continued. It means that data can live in FIFO. Current handling
just breaks out the request when seeing the command error. This causes
kernel panic in dw_mci_read_data_pio() [host->data = NULL]. And also,
FIFO should be guaranteed to be empty.
Unable to handle kernel NULL pointer dereference at virtual address 00000018
<...>
[<c02af814>] (dw_mci_read_data_pio+0x68/0x198) from [<c02b04b4>] (dw_mci_interrupt+0x374/0x3a0)
[<c02b04b4>] (dw_mci_interrupt+0x374/0x3a0) from [<c006b094>] (handle_irq_event_percpu+0x50/0x194)
[<c006b094>] (handle_irq_event_percpu+0x50/0x194) from [<c006b214>] (handle_irq_event+0x3c/0x5c)
[<c006b214>] (handle_irq_event+0x3c/0x5c) from [<c006de1c>] (handle_fasteoi_irq+0xa4/0x148)
[<c006de1c>] (handle_fasteoi_irq+0xa4/0x148) from [<c006aa88>] (generic_handle_irq+0x20/0x30)
[<c006aa88>] (generic_handle_irq+0x20/0x30) from [<c000f154>] (handle_IRQ+0x38/0x90)
[<c000f154>] (handle_IRQ+0x38/0x90) from [<c00085bc>] (gic_handle_irq+0x34/0x68)
[<c00085bc>] (gic_handle_irq+0x34/0x68) from [<c0011f40>] (__irq_svc+0x40/0x70)
Exception stack(0xef0b1c00 to 0xef0b1c48)
1c00: 000eb0cf ffffffff 00001300 c01a7738 ef295e10 0000000a c04df298 ef0b1dc0
1c20: ef295ec0 00000000 00000000 00000006 00000000 ef0b1c48 c02b1274 c01a7764
1c40: 20000113 ffffffff
[<c0011f40>] (__irq_svc+0x40/0x70) from [<c01a7764>] (__loop_delay+0x0/0xc)
Code: e1a00005 e0891006 e0662004 e12fff33 (e59a3018)
---[ end trace a7043b9ba9aed1db ]---
Kernel panic - not syncing: Fatal exception in interrupt
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Card Read Threshold should be ensured that the card clock does not stop
in the middle of a block of data being transferred from the card to the
Host. Specially, clock stop is allowed in fast transfer such as HS200
or SDR104 mode. And so, it should be enabled.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This change helps to choose msize, rx_watermark and tx_watermark
depending on block size for IDMAC mode. For SDIO block size can be
variable, so if these values are set incorrectly, card clock may stop.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Both f_max and f_min will be informed for core layer to request
valid clock rate. But current setting from 'host->bus_hz' may
not represent the max/min frequency properly. Even if host can
actually support high speed than bus_hz, core layer will not
request clock rate over bus_hz. Basically, f_max/f_min can be set
with the values according to spec. And then host will make its best
effort to meet the rate.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
'supports-highspeed' is not one of the quirks but is a capability.
So, it's removed from quirks.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
As host controller can support eMMC's HS200 mode at 1.8V or 1.2V,
these capability will be added.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
For the speed modes HS200 and SDR104, tuning is needed to determine the
correct sampling point. Actual tuning procedure is provided by specific
host controller driver. This patch defines the tuning command and
tuning data. Additionally, 'struct dw_mci_slot' is moved to header
file to consider the extensive usages in driver.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Current platform specific private data initialization call
dw_mci_exynos_priv_init() can be used to do platform specific
initialization of SMU and others in future. So the drv_data->init
call has moved to dw_mci_probe().
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The TMOUT register is set to 0xffffffff at probe time but isn't
set after suspend/resume. Add an init of this value.
No problems were observed without this (it will also be set in
__dw_mci_start_request if there is data to send), but it makes the
register dump before and after suspend cleaner.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Previously the dw_mmc driver would ignore any requests to disable the
card's clock. This doesn't seem like a good thing in general, but had
one extra bad side effect in the following situation:
* mmc core would set clk to 400kHz at boot time while scanning
* mmc core would set clk to 0 since no card, but it would be ignored.
* suspend to ram and resume; clocks in the dw_mmc IP block are now 0
but dw_mmc thinks that they're 400kHz (it ignored the set to 0).
* insert card
* mmc core would set clk to 400kHz which would be considered a no-op.
Note that if there is no card in the slot and we do a suspend/resume
cycle, we _do_ still end up with differences in a dw_mmc register
dump, but the differences are clock related and we've got the clock
disabled both before and after, so this should be OK.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The MMC subsystem handles looking for a card at probe time. Queuing up our
own can race with the rest of the MMC subsystem and cause problems if we
get unlucky with timing. Just remove driver own detection triggering. While
progressing the request from 'mmc_rescan', if 'dw_mci_work_routine_card'
routine is activated, it will cancel the current request. The problem case
is that 'mmc_rescan' is prior to 'dw_mci_work_routine_card' from host own.
Specifically, the following message shows the detection problem in driver's
probing. It would get an err -123 (-ENOMEDIUM) during probe.
[ 4.216595] dwmmc_exynos 12210000.dwmmc1: Using internal DMA controller.
[ 4.395935] dwmmc_exynos 12210000.dwmmc1: Version ID is 250a
[ 4.401948] dwmmc_exynos 12210000.dwmmc1: DW MMC controller at irq 108, 64 bit host data width, 64 deep fifo
[ 4.424430] dwmmc_exynos 12210000.dwmmc1: sdr0 mode (irq=108, width=0)
[ 4.453975] dwmmc_exynos 12210000.dwmmc1: sdr0 mode (irq=108, width=0)
[ 4.459592] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot req 400000Hz, actual 400000HZ div = 125)
[ 4.484258] dwmmc_exynos 12210000.dwmmc1: 1 slots initialized
[ 4.485406] dwmmc_exynos 12210000.dwmmc1: sdr0 mode (irq=108, width=0)
[ 4.487606] dwmmc_exynos 12210000.dwmmc1: sdr0 mode (irq=108, width=0)
[ 4.489794] dwmmc_exynos 12210000.dwmmc1: sdr0 mode (irq=108, width=0)
[ 4.509757] mmc1: error -123 whilst initialising SDIO card
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Core:
- Support Allocation Units 8MB-64MB in SD3.0, previous max was 4MB.
- The slot-gpio helper can now handle GPIO debouncing card-detect.
- Read supported voltages from DT "voltage-ranges" property.
Drivers:
- dw_mmc: Add support for ARC architecture, and support exynos5420.
- mmc_spi: Support CD/RO GPIOs.
- sh_mobile_sdhi: Add compatibility for more Renesas SoCs.
- sh_mmcif: Add DT support for DMA channels.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iQIcBAABAgAGBQJSLxu8AAoJEHNBYZ7TNxYMkV8P/RZMkP3L88wPmvdQ4IxVD/Bg
jphPsZTAlY8pLY7EcBVfbIGfBMMoVZ8CayuAbj9u5jFiMBNDUKRnKrky1m95F62n
xXiS5vUiKdWpByMpfKmrqvJr6eS8SWq5z/yug1c3s1Y9T363KgfypgJLvNgbMGiv
qbmjE+Zw65nMwHCk+4Rvq6s4aN6KosRZP0ABsn1foXt3kybSgemp5ShrlEyXohfS
E91EiYxHFC4fdmuWiZZvL1tyHFeV25omyZA90mpkioNItiwoyOM2rfjfEfNq+WBw
UrmdBesbGsF0Zi12CBa9LtzdRjYK8PugBWKW3mycS5++NX9KW6Ac/EpGqFeH9KgL
WZ2v4aQjkbnzQKUB2HcWAyXm88G9MkNvpLbIrmIPtson+q0UjgPYWe5BI3dy/Y1v
YS1JeseslVtSTKzGYsa1GJ7Nc1xYiILRz0RS4YGYXNjwvrl89i2UH7cglYDW36Xd
vxvRBaFpVsj1mfjjITEoG6nE0v5aYH6gSITY79XR+/kN871/99/oIUaWdpjcm9yv
SIYmK7ipcvxugkQ7BoMGbym/dvuUrZ+Vnf8dFlGPTJegZVsnfgrVAnRpvcVwW8+x
4Z79wUPSIETRqj2XX2I/Y0JnrXry+dLLVyeK1tELoeOKev73Ai2lcqPSz6J0tzJs
IErcz0hM1znL2RtgNwio
=+EYB
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.12:
Core:
- Support Allocation Units 8MB-64MB in SD3.0, previous max was 4MB.
- The slot-gpio helper can now handle GPIO debouncing card-detect.
- Read supported voltages from DT "voltage-ranges" property.
Drivers:
- dw_mmc: Add support for ARC architecture, and support exynos5420.
- mmc_spi: Support CD/RO GPIOs.
- sh_mobile_sdhi: Add compatibility for more Renesas SoCs.
- sh_mmcif: Add DT support for DMA channels"
* tag 'mmc-updates-for-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (50 commits)
Revert "mmc: tmio-mmc: Remove .set_pwr() callback from platform data"
mmc: dw_mmc: Add support for ARC
mmc: sdhci-s3c: initialize host->quirks2 for using quirks2
mmc: sdhci-s3c: fix the wrong register value, when clock is disabled
mmc: esdhc: add support to get voltage from device-tree
mmc: sdhci: get voltage from sdhc host
mmc: core: parse voltage from device-tree
mmc: omap_hsmmc: use the generic config for omap2plus devices
mmc: omap_hsmmc: clear status flags before starting a new command
mmc: dw_mmc: exynos: Add a new compatible string for exynos5420
mmc: sh_mmcif: revision-specific CLK_CTRL2 handling
mmc: sh_mmcif: revision-specific Command Completion Signal handling
mmc: sh_mmcif: add support for Device Tree DMA bindings
mmc: sh_mmcif: move header include from header into .c
mmc: SDHI: add DT compatibility strings for further SoCs
mmc: dw_mmc-pci: enable bus-mastering mode
mmc: dw_mmc-pci: get resources from a proper BAR
mmc: tmio-mmc: Remove .set_pwr() callback from platform data
mmc: tmio-mmc: Remove .get_cd() callback from platform data
mmc: sh_mobile_sdhi: Remove .set_pwr() callback from platform data
...
In (1fb5f68 mmc: dw_mmc: Don't loop when handling an interrupt), the
code for handling DW_MCI_QUIRK_IDMAC_DTO became dead code. Move it to
where it ought to live.
Found by code inspection and compile-tested only--I don't know of any
boards that need DW_MCI_QUIRK_IDMAC_DTO.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Use regulator_get_optional() to tell the core that requests for regulators
can fail in a real system.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Chris Ball <cjb@laptop.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
As of now we rely on code outside of the driver to set the ciu clock
frequency. There's no reason to do that. Add support for setting up
the clock in the driver during probe.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
It is possible to specify a regulator that should be turned on when
dw_mmc is probed. At the moment dw_mmc will fail to use the regulator
properly if the regulator probes after dw_mmc. Fix this problem by
honoring EPROBE_DEFER.
At the same time move the regulator code out of the slot init code.
We only specify one regulator for the whole device and other parts of
the code (like suspend/resume) assume that the regulator has only been
enabled once.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
At Interrupt status register, Bit9 is Data Read Timeout.
But we used macro name as the DTO. It could be confused with the
Data Transfer Over(DTO)-Bit[3].
It's clearly that is changed the DRTO instead of DTO.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fix to return -ENOMEM in alloc workqueue error case instead
of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
With device core now able to setup the default pin configuration,
the pin configuration code based on the deprecated Samsung specific
gpio bindings is removed.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
regulator_enable() is declared with __must_check attribute.
Hence check the return value to ensure that the regulator is enabled.
Fixes the following warning:
drivers/mmc/host/dw_mmc.c:2461:19: warning:
ignoring return value of ‘regulator_enable’, declared with attribute
warn_unused_result [-Wunused-result]
drivers/mmc/host/dw_mmc.c: In function ‘dw_mci_init_slot’:
drivers/mmc/host/dw_mmc.c:1994:19: warning:
ignoring return value of ‘regulator_enable’, declared with attribute
warn_unused_result [-Wunused-result]
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
When card is power-on/off, need to control the power-enable register.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
mci_writew causes a failure of fifo access for 64-bit.
mci_writeq is correct.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Commit f9c2a0dc42
"mmc: dw_mmc: Fix PIO mode with support of highmem" introduced
a regression since v3.2 making the mmc_test hang on test #13
with a "Data starvation by host timeout" interrupt.
This is because, sg_mapping_iter is used to iterate through the
data which spans on multiple pages. The problem is detected on
unaligned data submission where the code previously checked for
!(sg_next(host->sg)) which is true because we only have a single
scatter/gather list which then expands to multiple pages.
Therefore, the driver incorrectly assumed that this was the last
list item and submitted unaligned data to the mmc device. This
overflowed the FIFO on the device before all the data were written
to it. The code was fixed to only submit unaligned data when we are
handling the last sg_miter item by checking whether we reached
the desired data length or not.
The patch was tested against mmc_test and all the tests passed.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Previously, it was possible to add either 0 bytes or add nbytes
twice if we broke out of the outer loop and then carry on to the
"done" label. This is now fixed by adding the transferred bytes
right after the pull/pop operation
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
There is no reason to loop when handling an interrupt. The "if" clauses
will handle all of them sequentially. This also eliminates the extra loop
we used to take with no pending interrupts and we ended up breaking out
of the while loop.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
host->data_offset is initialised at the end of the probe function
depending on the VERID register, and is used for PIO operations. Move
this initialisation earlier, before IRQs or slots are initialised, to be
sure that PIO won't occur prior to host->data_offset being initialised.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Call the setpower platform callback in response to set_ios with
ios->power_mode == MMC_POWER_UP or MMC_POWER_OFF, instead of from the
card detect work function.
This appears to fix a problem I have where a card stuck in a funny state
doesn't get properly cleared by the power being turned off, presumably
due to lack of power sequencing. This resulted in the following log
messages after boot:
mmc0: error -110 whilst initialising SD card
mmc_host mmc0: Bus speed (slot 0) = 99840000Hz (slot req 300000Hz, actual 298922HZ div = 167)
mmc0: error -110 whilst initialising SD card
mmc_host mmc0: Bus speed (slot 0) = 99840000Hz (slot req 200000Hz, actual 199680HZ div = 250)
mmc0: error -110 whilst initialising SD card
mmc_host mmc0: Bus speed (slot 0) = 99840000Hz (slot req 195765Hz, actual 195764HZ div = 255)
mmc0: error -110 whilst initialising SD card
mmc_host mmc0: Bus speed (slot 0) = 99840000Hz (slot req 400000Hz, actual 399360HZ div = 125)
mmc0: error -110 whilst initialising SD card
mmc_host mmc0: Bus speed (slot 0) = 99840000Hz (slot req 300000Hz, actual 298922HZ div = 167)
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In the legacy code, driver clear not only UHS_REG 16 bit also 0-15bit.
If we use UHS-1 mode spec card like SDR50, SDR104. UHS_REG 0-15 should
be set by 1 according to slot id. In this case, legacy code can cause
problems.
In particular, UHS_REG consists of DDR_REG[31:16] and VOLT_REG[15:0].
Before adjusting this patch, bit[15:0] is always cleared.
Signed-off-by: Hyeonsu Kim <hyeonsu.kim@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In dwc manual, the below contents are described:
"During end of packet, interrupt is not generated if threshold
programming is larger than any remaining data. It is responsibility
of host to read remaining bytes on seeing Data Transfer Done
interrupt"
We also have seen the data cannot be read fully when
"sg_miter->length" is less than FIFO size.
Signed-off-by: Kyoungil Kim <ki0351.kim@samsung.com>
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Check the result of mmc_add_host() and return the value.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
For better code reuse use the newly added page iterator to iterate
through the pages. The offset, length within the page is still
calculated by the mapping iterator as well as the actual mapping. Idea
from Tejun Heo.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The original quirk was added in the change 'mmc: dw_mmc: add quirk to
indicate missing write protect line'. The original quirk was added at
a controller level even though each slot has its own write protect (so
the quirk should be at the slot level). A recent change (mmc: dw_mmc:
Add "disable-wp" device tree property) added a slot-level quirk and
support for the quirk directly to dw_mmc.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Will Newton <will.newton@imgtec.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
On some SoCs (like exynos5250) you need to use an external GPIO for
write protect. Add support for wp-gpios to the core dw_mmc driver
since it could be useful across multiple SoCs.
With this change I am able to make use of the write protect for the
external SD slot on exynos5250-snow.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
The "disable-wp" property is used to specify that a given SD card slot
doesn't have a concept of write protect. This eliminates the need for
special case code for SD slots that should never be write protected
(like a micro SD slot or a dev board).
The dw_mmc driver is special in needing to specify "disable-wp"
because the lack of a "wp-gpios" property means to use the special
purpose write protect line. On some other mmc devices the lack of
"wp-gpios" means that write protect should be disabled.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
ctype is using 1-bit buswidth mode by default.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
To ensure the stable clock need to enable before set the
DW_MMC_CARD_NEED_INIT flag. If set DW_MMC_CARD_NEED_INIT flag,
wait for 80-clock before first command after power-up.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Use managed device resource functions for easy handling.
This makes driver simpler in the routine of error and exit.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add dt-based retrieval of host sdio pm capabilities. Based on
the dt based discovery do a bus init in the resume function.
Signed-off-by: Olof Johansson <olofj@chromium.org>
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The patch "dw_mmc: fix multiple drv_data NULL dereferences" has
unfortunately clashed with my "mmc: dw_mmc: constify dw_mci_idmac_ops
in exynos back-end" patch, causing new warnings to appear.
This should hopefully fix the issue for good.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
The of_device_id match data is now marked as const and
must not be modified. This changes the dw_mmc to mark
all pointers passing the dw_mci_drv_data or dw_mci_dma_ops
structures as const, and also marks the static definitions
as const.
drivers/mmc/host/dw_mmc-exynos.c: In function 'dw_mci_exynos_probe':
drivers/mmc/host/dw_mmc-exynos.c:234:11: warning: assignment discards 'const' qualifier from pointer target type [enabled by default]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Cc: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
800d78bfcc ("mmc: dw_mmc: add support for implementation specific
callbacks") -- merged in v3.7-rc1 -- introduced multiple NULL pointer
dereferences when the default dw_mci_pltfm_probe() is used, as it sets
host->drv_data to NULL, and that's only checked against NULL in 1 out of
the 7 cases where it is dereferenced.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
As mmc_start_host is getting called before enabling the dw_mmc controller
interrupt, there is a problem of missing the SDMMC_INT_CMD_DONE for the
very first command sent by the sdio_reset.
This problem occurs only when we disable MMC debugging i.e, MMC_DEBUG=n.
This patch enables the dw_mmc controller interrupt before mmc_start_host.
Signed-off-by: Yuvaraj CD <yuvaraj.cd@samsung.com>
Reviewed-by: Girish K S <girish.shivananjappa@linaro.org>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch removes the following warning.
drivers/mmc/host/dw_mmc.c:1976: warning: passing argument 1 of
'_dev_info' from incompatible pointer type
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch fixes up the broken suspend sequence for eMMC with sleep
support. Additionally it reworks the eMMC4.5 Power Off Notification
feature so it fits together with the existing sleep feature.
The CMD0 based re-initialization of the eMMC at resume is re-introduced
to maintain compatiblity for devices using sleep.
A host shall use MMC_CAP2_POWEROFF_NOTIFY to enable the Power Off
Notification feature. We might be able to remove this cap later on,
if we think that Power Off Notification always is preferred over
sleep, even if the host is not able to cut the eMMC VCCQ power.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Saugata Das <saugata.das@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This reverts commit 94c6cee91 (Add check for IDMAC configuration).
Synopsys says that only if internal dmac is not present, optional
external dma interface is present. When internal dmac is present,
'0' value in DMA_INTERFACE of HCON is reasonable. DMA_INTERFACE
indicates external dma interface. And idmac initialization is
prohibited now.
The commit should be reverted since: the check for IDMAC is not
reliable; falling back to PIO would provide awful performance; we
wouldn't expect to see instances of this block without DMA support.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The core dw-mshc controller driver can let platform specific
implementations of the dw-mshc controller to control the hardware
as required by such implementations. This is acheived by invoking
implementation specific (optional) callbacks. Define the list of
callbacks supported the add invocation points for the same.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add device tree based discovery support.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
If the write protect pad of the controller is not connected to the write
protect pin of the slot, the driver should be notified of this condition
so that incorrect check for write protection by reading the WRTORT
register can avoided. The get_ro platform callback can be used for in
such cases, but with device tree support enabled, such platform callbacks
cannot be supported.
Add a new quirk for notifying the driver about the missing write protect
line so the driver can assume that the card write protection is disabled.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some platforms allow for clock gating and control of bus interface unit
clock and card interface unit clock. Add support for clock lookup of
optional biu and ciu clocks for clock gating and clock speed
determination.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Instead of aborting the probe when a slot initialization fails, allow
initialization of as many slots as possible. If there is at least one
instance of a slot that is successfully initialized, allow the driver
probe to succeed.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The 'struct dw_mci' maintains a copy of the pdev->dev instance instead of
maintaining a reference to that 'struct device' instance. Any resource
allocated using the device resource management kernel API with the instance
of 'struct device' in 'struct dw_mci' is then incorrect. Fix this by
converting the copy of 'struct device' in 'struct dw_mci' to a reference.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fixed the below message.
WARNING: drivers/mmc/host/built-in.o(.text+0x5ee8): Section mismatch in reference from the function dw_mci_probe() to the function .init.text:dw_mci_init_slot()
The function dw_mci_probe() references
the function __init dw_mci_init_slot().
This is often because dw_mci_probe lacks a __init
annotation or the annotation of dw_mci_init_slot is wrong
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The documentation for the dw_mmc part says that the low power
mode should normally only be set for MMC and SD memory and should
be turned off for SDIO cards that need interrupts detected.
The best place I could find to do this is when the SDIO interrupt
was first enabled. I rely on the fact that dw_mci_setup_bus()
will be called when it's time to reenable.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Data transfer will be continued until all the bytes are transmitted,
even if data crc error occurs during a multiple-block data transfer.
This means RXDR/TXDR interrupts will occurs until data transfer is
terminated. Early setting of host->sg to NULL prevents going into
xxx_data_pio functions, hence permanent unhandled RXDR/TXDR interrupts
occurs. And checking error interrupt status in the xxx_data_pio functions
is no need because dw_mci_interrupt does do the same. This patch also
removes it.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Datasheet of SYNOPSYS mentions that DTO(Data Transfer Over) interrupt
will be raised even if some error interrupts, however it is actually
found that DTO does not occur. SYNOPSYS has confirmed this issue.
Current implementation defers the call of tasklet_schedule until DTO
when the error interrupts is happened. This patch fixes error handling.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
RINTSTS status includes masked interrupts as well as unmasked.
data_status and cmd_status are set by value of RINTSTS in interrupt handler
and tasklet finally uses it to decide whether error is happened or not.
In addition, MINTSTS status is used for setting data_status in PIO.
Masked error interrupt will not be handled and that status can be considered
non-error case.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed By: Girish K S <girish.shivananjappa@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
host->dma_ops is not valid if host->usa dma is 0 so protect
host->dma_ops reference in dw_mci_resume
Signed-off-by: Jonathan Kliegman <kliegs@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In the current dwmmc driver there is support for selecting IDMAC from
the menu config option. If the support for IDMAC is enabled in the menu
config and the hardware configuration register's DMA_INTERFACE field is
0, the driver will still try to do the DMA initialization.
The dw_mci_idmac_init function currently implemented returns only success
indicating that the DMA initialization is always successful. This patch
adds a check for existence of the DMA IP to allow the DMA initialization.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In case of "host->bus_hz < slot->clock", divider value is
miscalculated. And clock divider register value is multiple of 2. If
calculated divider value is odd number, result can be over-clocking.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Setting host->data to NULL is incorrect sequence in
dw_mci_command_complete. This early setting makes the skip of
dma_unmap_sg in dw_mci_dma_cleanup.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
IDMAC may not be cleaned in driver probe if it has been already used in
boot time. So IDMAC needs sw reset newly. And DMA interface reset
precedes the internal DMAC reset. Additionally SDMMC_IDMAC_SWRESET is
replaced with magic code.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
DTO interrupt can be later than transmit interrupt(IDMAC) in case of
write. Current handling of IDMAC interrupt sets EVENT_DATA_COMPLETE as
well as EVENT_XFER_COMPLETE regardless of DTO rising. This makes the
current request finish in tasklet and permits the next request even
though current data transfer is still in progress. As a result, sequence
is broken and lock-up happens. Setting EVENT_DATA_COMPLETE is not proper
after IDMAC interrupt. It should be taken after DTO interrupt is
generated.
Reported-by: Dmitry Shmidt <dimitrysh@android.com>
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Hyeonsu Kim <hyeonsu.kim@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The sdio interrupt mask bits are arranged in [31:16].
(1 << SDMMC_INT_SDIO(slot->id))) does 16 bits left shift twice.
So this patch changes to do 16 bits left shift only one time.
Signed-off-by: Kyoungil Kim <ki0351.kim@samsung.com>
Acked-by: Shashidhar Hiremath <shashidharh@vayavyalabs.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The variable 'dw_mci_card_workqueue' is a global variable shared between
multiple instances of the dw_mmc host controller. Due to this, data
corruption has been noticed when multiple instances of dw_mmc controllers
are actively reading/writing the media. Fix this by adding a instance
of 'struct workqueue_struct' for each host instance and removing the
global 'dw_mci_card_workqueue' instance.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Now, dma_ops is assumed that use the IDMAC. But if dma_ops is assigned
the pdata->dma_ops, we didn't ensure that callback function is defined.
If the callback isn't defined, then we should run in PIO mode.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
When dw_mci_pre_dma_transfer returns failure in some reasons,
dw_mci_submit_data will prepare to switch the PIO mode from DMA.
After switching to PIO mode, DMA(IDMAC in particular) is still
enabled. This makes the corruption in handling interrupt and
the driver lock-up.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
3ec7699d3bb1b0ee7 ("mmc: dw_mmc: Add support for pre_req and post_req")
broke non-IDMAC DMA, because dw_mci_pre_dma_transfer() is valid only if
using internal DMA. In case of using other DMA it returns -ENOSYS. It
prevents the DMA operations. This patch makes dw_mci_pre_dma_transfer()
effective in all DMA cases again.
Reported-by: James Hogan <james@albanarts.com>
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
When disable CONFIG_MMC_DW_IDMAC, can see the compiler error.
Because in dw_mci_post_req(), called the dw_mci_get_dma_dir().
But that function is in #ifdef CONFIG_MMC_DW_IDMAC.
I think that function is generic function.
Not need the CONFIG_MMC_DW_IDMAC.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In CLKENA register, can support 16-SD card clocks.
If support correctly, must shift with slot-id.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch implements pre_req and post_req in dw_mmc to support
asynchronous mmc request.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
When use the IDMAC, we can also want to use the pdata->blk-setting.
So if pdata->blk-setting is unset, use the default value.
if not, use the pdata->blk-setting.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Support of PCI mode for the dw_mmc driver. This Patch adds the
support for the scenario where the Synopsys Designware IP
is present on the PCI bus. The patch adds the minimal modifications
necessary for the driver to work on PCI platform. Also added separate
files for PCI and PLATFORM modes of operation.
Signed-off-by: Shashidhar Hiremath <shashidharh@vayavyalabs.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds the capability of power off notify for dw-mmc controller.
In order to use Girish's patch:
mmc: core: Add Power Off Notify Feature eMMC 4.5
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In FIFOTH register, the RX_WMark field (bits[27:16]) defaults to
FIFO_DEPTH - 1. When reading it, bits[26:16] were being used, so
fix it to use the mask 0xfff instead of 0x7ff.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
UHS_REG should be cleared for non-DDR mode. But currently there is
no way to clear DDR mode, if it is already set once. This patch adds
clearing DDR mode for non-DDR mode.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds the support for predefined multiple block r/w.
dw_mmc can support MMC_CAP_CMD23 capability.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds another capabilities field for MMC_CAPS2_XXX.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch modifies dw_mmc to use dev_pm_ops.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In dw_mmc 2.40a spec, Data register's offset is changed.
Before we used Data register offset 0x100. but if somebody uses a
2.40a controller, we must use 0x200 for Data register.
This patch adds a version-id checking point and uses SDMMC_DATA(x)
instead of SDMMC_DATA. It assumes 2.40a is the latest version.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
All the files using printk function for displaying kernel messages
in the mmc driver have been replaced with corresponding macro.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The Patch adds the support for SDIO interrupts for all slots.
It includes enabling of SDIO interrupts through dw_mci_enable_sdio_irq
and the handling of the slot specific interrupts in the Interrupt Service
Routine.
Signed-off-by: Shashidhar Hiremath <shashidharh@vayavyalabs.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Host driver can't get a hint of DDR mode through ios->ddr flag anymore.
ios->timing is currently used to inform DDR mode as a substitute.
And capability of MMC_CAP_MMC_HIGHSPEED is added for DDR support.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The mask used inside this macro was assuming Buffer_Size1's [BS1's]
width to be 14 bits, it is actually 13 bits. Modify masks used in
IDMAC_SET_BUFFER1_SIZE such that they use only 13 bits instead of
current 14.
Signed-off-by: Shashidhar Hiremath <shashidharh@vayavyalabs.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
If an error occurs mid way through a transaction (such as a missing CRC
status response after the 2nd block written out of 3), then the FIFO may
still contain data which will interfere with the next transaction.
Therefore after an error has been detected, reset the fifo using the
CTRL register.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
When a data write isn't acknowledged by the card (so no CRC status token
is detected after the data), the error -EIO is returned instead of the
-ETIMEDOUT expected by mmc_test 15 - "Correct xfer_size at write (start
failure)" and 17 "Correct xfer_size at write (midway failure)". In PIO
mode the reported number of bytes transferred is also exaggerated since
the last block actually failed.
Handle the "Write no CRC" error specially, setting the error to
-ETIMEDOUT and setting the bytes_xferred to 0.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Remove error messages for timeout and CRC failure, since the error code
already indicates the problem.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
There are several situations when dw_mci_submit_data_dma() decides to
fall back to PIO mode instead of using DMA, due to a short (to avoid
overhead) or "complex" (e.g. with unaligned buffers) transaction, even
though host->use_dma is set. However dw_mci_stop_dma() decides whether
to stop DMA or set the EVENT_XFER_COMPLETE event based on host->use_dma.
When falling back to PIO mode this results in data timeout errors
getting missed and the driver locking up.
Therefore add host->using_dma to indicate whether the current
transaction is using dma or not, and adjust dw_mci_stop_dma() to use
that instead.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Update functions for PIO pushing and pulling data to and from the FIFO
so that they can handle unaligned output buffers and unaligned buffer
lengths. This makes more of the tests in mmc_test pass.
Unaligned lengths in pulls are handled by reading the full FIFO item,
and storing the remaining bytes in a small internal buffer (part_buf).
The next data pull will copy data out of this buffer first before
accessing the FIFO again. Similarly, for pushes the final bytes that
don't fill a FIFO item are stored in the part_buf (or sent anyway if
it's the last transfer), and then the part_buf is included at the
beginning of the next buffer pushed.
Unaligned buffers in pulls are handled specially if the architecture
cannot do efficient unaligned accesses, by reading FIFO items into a
aligned local buffer, and memcpy'ing them into the output buffer, again
storing any remaining bytes in the internal buffer. Similarly for pushes
the buffer is memcpy'd into an aligned local buffer then written to the
FIFO.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The FIFO_DEPTH hardware configuration parameter can be found from the
power-on value of RX_WMark in the FIFOTH register. This is used to
initialise the watermarks, but when calculating the number of free fifo
spaces a preprocessor definition is used which is hard coded to 32.
Fix reading the value out of FIFOTH (the default value in the RX_WMark
field is FIFO_DEPTH-1 not FIFO_DEPTH). Allow the fifo depth to be
overriden by platform data (since a bootloader may have changed FIFOTH
making auto-detection unreliable). Store the fifo_depth for later use.
Also fix the calculation to find the number of free bytes in the fifo to
include the fifo depth in the left shift by the data shift, since the
fifo depth is measured in fifo items not bytes.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Doug Anderson