* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
bridge: fix forwarding of IPv6
bonding,llc: Fix structure sizeof incompatibility for some PDUs
ipv6: restore correct ECN handling on TCP xmit
ne-h8300: Fix regression caused during net_device_ops conversion
hydra: Fix regression caused during net_device_ops conversion
zorro8390: Fix regression caused during net_device_ops conversion
sfc: Always map MCDI shared memory as uncacheable
ehea: Fix memory hotplug oops
libertas: fix cmdpendingq locking
iwlegacy: fix IBSS mode crashes
ath9k: Fix a warning due to a queued work during S3 state
mac80211: don't start the dynamic ps timer if not associated
->read_proc interface is going away, switch to seq_file.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a bug in the set_pauseparam
function that didn't well manage the ANE
field and returned broken values when use
ethtool -A|-a.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver used to call phy's ethtool configuration routine to start
auto-negotiation. This change has it call directly phy's routine to
start auto-negotiation.
The initial version was hiding phy_start_aneg() return value,
this patch returns it (<0 upon error).
Tested: module compiles, tested on STM HDK7108 STB.
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With some combinations of arch/compiler (e.g. arm-linux-gcc) the sizeof
operator on structure returns value greater than expected. In cases when the
structure is used for mapping PDU fields it may lead to unexpected results
(such as holes and alignment problems in skb data). __packed prevents this
undesired behavior.
Signed-off-by: Vitalii Demianets <vitas@nppfactor.kiev.ua>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the PAN context is active, but unused, it
may still block scans that take more dwell time
than its beacon interval (which is odd). Work
around this problem by using a default beacon
interval of 200 so scans will fit between.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
gcc is warning that a few variables in rate
scaling are set but never otherwise used.
This pointed out a few simplifications.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Before send the RXON command with associated flag set, always do disassociate
first to make sure uCode is in the correct state.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
No functional changes, just logging more information when uCode crash, also
change change the format.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The current "huge" command handling is a bit
confusing, and very limited since only one
command may be huge at a time. Additionally,
we often copy data around quite pointlessly
since we could instead map the existing scan
buffer for example and use it directly.
This patch makes that possible. The first
change is that multiple buffers may be given
to each command (this change was prepared
earlier so callsites don't need to change).
Each of those can be mapped attached to a TB
in the TFD, and the command header can use a
TB (the first one) in the TFD as well.
Doing this allows getting rid of huge commands
in favour of mapping existing buffers. The
beacon transmission is also optimised to not
copy the SKB at all but use multiple TBs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Driver checks if the previous dump has been cleared before taking the dump.
It doesn't take the dump if it is not cleared.
Changes from v2:
Added lock to protect dump data structures from being mangled while
dumping or setting them via ethtool.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added code to take FW dump.
o Driver queries FW at the init time and gets the dump template
o It takes FW dump as per the dump template
o Level of FW dump (and its size) is configured via dump flag
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sending mbox cmds require multiple steps of writing to the DB register and polling
for an ack. Gettting interrupted in the middle by a signal breaks the mbox protocol.
Use msleep() to not get interrupted.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If waiting on POST returns prematurely (due to a signal), abort polling and return an error.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pad argument to iwlagn_txq_free_tfd
isn't used, remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
All of these functions no longer need to be
accessed indirectly since they're shared in
all AGN devices.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
In a subsequent patch, I want to make commands use
multiple TBs in a TFD. This is a simple change to
prepare the data structures for this, with as of
now still just a single TB supported.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
When operating as station, enter psm before suspending
the device into wowlan state.
Add a new completion event to signal when psm was entered
successfully.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Since wowlan requires the ability to stay awake while the host
is suspended, declare support for NL80211_WOW_TRIGGER_ANYTHING
if the MMC_PM_KEEP_POWER capability is being supported.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When WoW is enabled, the interface will stay up and the chip will
be powered on, so we have to flush/cancel any remaining work, and
prevent the irq handler from scheduling a new work until the system
is resumed.
Add 2 new flags:
* WL1271_FLAG_SUSPENDED - the system is (about to be) suspended.
* WL1271_FLAG_PENDING_WORK - there is a pending irq work which
should be scheduled when the system is being resumed.
In order to wake-up the system while getting an irq, we initialize
the device as wakeup device, and calling pm_wakeup_event() upon
getting the interrupt (while the system is about to be suspended)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
if a wow trigger was configured, set the MMC_PM_KEEP_POWER flag
on suspend, so our power will be kept while the system is suspended.
We needed to set this flag on each suspend attempt (when we want
to keep power)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Additionally, add wow_enabled field to wl, to indicate
whether wowlan was configured.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
set the sdio interrupt as wake_up interrupt, so we will be able
to wake up the suspended system (Wake-On-Wireless)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
This should also fix updating of vlan_features and propagating changes to
VLAN devices on the bond.
Side effect: it allows user to force-disable some offloads on the bond
interface.
Note: NETIF_F_VLAN_CHALLENGED is managed by bond_fix_features() now.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes:
- while making NTB, driver shall check if device dwNtbOutMaxSize is higher than
host value and shall add a short packet if this is the case
- previous temporary patch for this issue is replaced by this one
Signed-off-by: Alexey Orishko <alexey.orishko@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds tg3_set_features() to handle loopback mode. Currently the
capability is added for the devices which support internal MAC loopback mode.
So when enabled, it enables internal-MAC loopback.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resending this patch with few changes.
Avoid multiple queues when MSI or MSI-X not available
Limit number of Tx queues to 1 if MSI/MSI-X support is not configured in
the kernel. This will make number of tx and rx queues equal when MSI/X
is not configured thus providing better performance.
Signed-off-by: Bhavesh Davda <bhavesh@vmware.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current firmware only supports scheduled scan in station mode and
when idle. To prevent the firmware from crashing, return -EOPNOTSUPP
when sched_scan start is called in an invalid state.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Subscribe and listen to PERIODIC_SCAN_REPORT_EVENT_ID and
PERIODIC_SCAN_COMPLETE_EVENT_ID in preparation for the scheduled scan
implementation.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Set the spectrum management bit in the hw flags so that mac80211 will
set the WLAN_CAPABILITY_SPECTRUM_MGMT bit in association requests
(which in practice means that we support 802.11h spectrum management).
[Reworded the commit log -- Luca.]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
This patch adds a beacon filter rule to pass up the beacons that
contain changed HT information elements. These beacons need to be
passed to mac80211 so that it can act on such changes.
[Reworded commit log -- Luca.]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Simplify wl1271_ssid_set by re-using cfg80211_find_ie instead of
reimplementing it.
Additionally, add a length check to prevent a potential buffer overflow.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Changeset dcd39c9029 ("ne-h8300: convert to
net_device_ops") broke ne-h8300 by adding 8390.o to the link. That
meant that lib8390.c was included twice, once in ne-h8300.c and once in
8390.c, subject to different macros. This patch reverts that by
avoiding the wrappers in 8390.c.
Fix based on commits 217cbfa856 ("mac8390:
fix regression caused during net_device_ops conversion") and
4e0168fa48 ("mac8390: fix build with
NET_POLL_CONTROLLER").
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Changeset 5618f0d119 ("hydra: convert to
net_device_ops") broke hydra by adding 8390.o to the link. That
meant that lib8390.c was included twice, once in hydra.c and once in
8390.c, subject to different macros. This patch reverts that by
avoiding the wrappers in 8390.c.
Fix based on commits 217cbfa856 ("mac8390:
fix regression caused during net_device_ops conversion") and
4e0168fa48 ("mac8390: fix build with
NET_POLL_CONTROLLER").
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Changeset b6114794a1 ("zorro8390: convert to
net_device_ops") broke zorro8390 by adding 8390.o to the link. That
meant that lib8390.c was included twice, once in zorro8390.c and once in
8390.c, subject to different macros. This patch reverts that by
avoiding the wrappers in 8390.c.
Fix based on commits 217cbfa856 ("mac8390:
fix regression caused during net_device_ops conversion") and
4e0168fa48 ("mac8390: fix build with
NET_POLL_CONTROLLER").
Reported-by: Christian T. Steigies <cts@debian.org>
Suggested-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Christian T. Steigies <cts@debian.org>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
XB113 (AR9380) 3x3 SB 5G only cards were failing to connect to APs
due to incorrect xpabiaslevel configuration. fix it.
Cc: stable@kernel.org
Cc: Ray Li <ray.li@greenwavereality.com>
Cc: Kathy Giori <kathy.giori@atheros.com>
Cc: Aeolus Yang <aeolus.yang@atheros.com>
Cc: compat@orbit-lab.org
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function
- increments dropped rx_packet count if status code
passed to it is "-1".
- frees SKB buffer.
But currently the function is being called with "0" status code.
This patch replaces above function by dev_kfree_skb_any() call.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The XB113 cards are single band, 5 GHz-only, but the
default settings were configured to assume it was dual
band. Users of these cards then would see 2.4 GHz channels
but you would never get any scan results from these channels
given that the radio is not present.
Cc: stable@kernel.org
Cc: Fiona Cain <Fiona.Cain@atheros.com>
Cc: Ray Li <ray.li@greenwavereality.com>
Cc: Kathy Giori <kathy.giori@atheros.com>
Cc: Aeolus Yang <aeolus.yang@atheros.com>
Cc: Dan Friedman <dan.friedman@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6870/1: The mandatory barrier rmb() must be a dsb() in for device accesses
ARM: 6892/1: handle ptrace requests to change PC during interrupted system calls
ARM: 6890/1: memmap: only free allocated memmap entries when using SPARSEMEM
ARM: zImage: the page table memory must be considered before relocation
ARM: zImage: make sure not to relocate on top of the relocation code
ARM: zImage: Fix bad SP address after relocating kernel
ARM: zImage: make sure the stack is 64-bit aligned
ARM: RiscPC: acornfb: fix section mismatches
ARM: RiscPC: etherh: fix section mismatches
We enabled write-combining for memory-mapped registers in commit
65f0b417de, but inhibited it for the
MCDI shared memory where this is not supported. However,
write-combining mappings also allow read-reordering, which may also
be a problem.
I found that when an SFC9000-family controller is connected to an
Intel 3000 chipset, and write-combining is enabled, the controller
stops responding to PCIe read requests during driver initialisation
while the driver is polling for completion of an MCDI command. This
results in an NMI and system hang. Adding read memory barriers
between all reads to the shared memory area appears to reduce but not
eliminate the probability of this.
We have not yet established whether this is a bug in our BIU or in the
PCIe bridge. For now, work around by mapping the shared memory area
separately.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Start/stop TX queue is controlled by TX queue "used" counter.
It is incremented while WRBs are posted to TX queue and
decremented when TX completions are received. This counter was
getting decremented before HW is informed about processing of TX
completions. As used counter is decremented, transmit function
posts new WRBs and creates completion queue full scenario in HW.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use OPCODE_COMMON_NTWK_RX_FILTER command for promiscous mode as
OPCODE_ETH_PROMISCUOUS command is getting deprecated.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of UE, do not dump registers for Lancer as they are not
supported.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable coalesce water mark mode of CQ for Lancer
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Lancer if a frame is DMAed partially due to lack of RX buffers,
an error completion is sent with packet size as zero and num_recvd
indicating number of used buffers. These buffers need to be freed
and packet dropped.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows individual users and deployments to disable mesh support at
runtime, i.e. without having to build and maintain a custom kernel.
Based on a patch by Paul Fox <pgf@laptop.org>.
Signed-off-by: Sascha Silbe <silbe@activitycentral.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some structures and macros in ioctl.h are redundant or no longer
used.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Avoid use of local structure in the function if the structure is
already allocated by the caller and the structure pointer is passed.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Only leave filtering enabled for AP or VLAN interfaces, clear the
destination mask for all other interfaces.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Ben Greear <greearb@candelatech.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is not N-PHY specific function, we partially duplicate code.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This was introduced in 2.6.39-rc1 it seems.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Sedat Dilek <sedat.dilek@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mesh beaconing on ath9k was broken by this commit:
commit 4801416c76
Author: Ben Greear <greearb@candelatech.com>
Date: Sat Jan 15 19:13:48 2011 +0000
This patch assigns the right opmode when the device is used in mesh
mode.
Reported-by: Fabrice Deyber fabricedeyber@agilemesh.com
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using the more descriptive logging styles gives a bit
more information about the device being operated on.
Makes the object trivially smaller too.
$ size drivers/net/wireless/libertas/built-in.o.*
187730 2973 38488 229191 37f47 drivers/net/wireless/libertas/built-in.o.new
188195 2973 38488 229656 38118 drivers/net/wireless/libertas/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the standard pr_<level> functions eases grep a bit.
Added a few missing terminating newlines to messages.
Coalesced long formats.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TTY layer expects 0 if the ldisc->open operation succeeded.
Reported-by: Matvejchikov Ilya <matvejchikov@gmail.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like other mobile broadband device ethernet interfaces, mark the LG
VL600 with the 'wwan' devtype so userspace knows it needs additional
configuration via the AT port before the interface can be used.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The structure definition is
struct mwifiex_opt_sleep_confirm_buffer {
u8 hdr[4];
struct mwifiex_opt_sleep_confirm ps_cfm_sleep;
} __packed;
For sleep_confirm command we already reserve 4 bytes (using skb_reserve())
for an interface header. It will be filled later by interface specific code.
We don't need "hdr[4]" element in above structure. So we can use
"struct mwifiex_opt_sleep_confirm" directly instead of
"struct mwifiex_opt_sleep_confirm_buffer".
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This beacon rssi will be used to set noisefloor during ani reset.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The average beacon rssi which will be used by ani is not updated
in adhoc mode.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By changing DCU backoff threshold for AR9340 to 1, helps to
reduce rx overrurns seen while running bidirectional traffic.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Found via coccinelle script
@@
type T;
T* ptr;
expression E1;
@@
* memset(E1, 0, sizeof(ptr));
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
currently ath9k_hw_getchan_noise is not used anywhere
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This can be helpful when we decide to add support for other buses.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch:
- adds kfree() where necessary
- prevents potential null dereferences
- makes use of kfree_skb()
- replaces -1 for failed kzallocs with -ENOMEM
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Reviewed-by: Kiran Divekar <dkiran@marvell.com>
Tested-by: Amitkumar Karwar <akarwar@marvell.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the code to detect inactive 802.11 cores, as that function is now done
in ssb.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the code to detect inactive 802.11 cores, as that function is now done
in ssb.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
txstatus_timer should only be deleted for USB devices, as it is only
initialized for USB devices.
Reported-by: Andreas Hartmann <andihartmann@01019freenet.de>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
p54pci.c: In function ‘p54p_tx’:
p54pci.c:334:6: warning: variable ‘device_idx’ set but not used
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
tx.c: In function ‘carl9170_tx_accounting_free’:
tx.c:159:28: warning: variable ‘txinfo’ set but not used
tx.c: In function ‘carl9170_tx_status_process_ampdu’:
tx.c:383:27: warning: variable ‘ar_info’ set but not used
tx.c: In function ‘__carl9170_tx_process_status’:
tx.c:626:27: warning: variable ‘arinfo’ set but not used
tx.c: In function ‘carl9170_tx_ampdu_queue’:
tx.c:1324:15: warning: variable ‘max’ set but not used
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When this driver was initially submitted, the system would crash unless
ASPM was disabled. This problem has been fixed.
This patch also adds a printk that outputs the name of the firmware
file that is used.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In driver rtlwifi, efuse_read() places two relatively large arrays on the
stack - a 1D u8 array of size 128, and a 2D array of u16 with 128 * 4 elements.
With driver rtl8192de, the sizes will be 256 and 256 * 4 respectively. As that
will make the 2D array be 2048 bytes, I have changed the code to use kmalloc to
allocate the space.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function iwl_is_any_associated() was intended
to check both contexts, but due to an oversight
it only checks the BSS context. This leads to a
problem with scanning since the passive dwell
time isn't restricted appropriately and a scan
that includes passive channels will never finish
if only the PAN context is associated since the
default dwell time of 120ms won't fit into the
normal 100 TU DTIM interval.
Fix the function by using for_each_context() and
also reorganise the other functions a bit to take
advantage of each other making the code easier to
read.
Cc: stable@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Processing TSF out of range before RX helps to update beacon
timers so early in the succeeding rx process.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The assumsion is that while processing ath9k tasklet,
interrupts were already disabled and it will be enabled
at the completion of ath9k tasklet. But whenever TSFOOR is raised,
the driver configures the beacon timers after having received a
beacon frame from the AP which inturn enables the interrupts.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit 5ed540aecc change the led behavior
for iwlwifi driver; the side effect cause led blink all the time.
Modify the led blink table to fix this problem
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We occasionally see list corruption using libertas.
While we haven't been able to diagnose this precisely, we have spotted
a possible cause: cmdpendingq is generally modified with driver_lock
held. However, there are a couple of points where this is not the case.
Fix up those operations to execute under the lock, it seems like
the correct thing to do and will hopefully improve the situation.
Signed-off-by: Paul Fox <pgf@laptop.org>
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should not switch to non-IBSS channels when working in IBSS mode,
otherwise there are microcode errors, and after some time system
crashes.
This bug is only observable when software scan is used in IBSS mode,
so should be considered as regression after:
commit 0263aa4529
Author: Stanislaw Gruszka <sgruszka@redhat.com>
Date: Tue Mar 29 11:24:21 2011 +0200
iwl3945: disable hw scan by default
However IBSS mode check, which this patch add again, was removed by
commit b2f30e8bdd
Author: Johannes Berg <johannes.berg@intel.com>
Date: Thu Jan 21 07:32:20 2010 -0800
iwlwifi: remove IBSS channel sanity check
That commit claim that mac80211 will not use non-IBSS channel in IBSS
mode, what definitely is not true. Bug probably should be fixed in
mac80211, but that will require more work, so better to apply that patch
temporally, and provide proper mac80211 fix latter.
Resolves:
https://bugzilla.kernel.org/show_bug.cgi?id=34452
Reported-and-tested-by: Mikko Rapeli <mikko.rapeli@iki.fi>
Cc: stable@kernel.org # 2.6.38.5+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
during suspend/S3 state drv_flush is called from mac80211 irrespective of
interface count. In ath9k we queue a work in ath9k_flush which we expect
to be cancelled in the drv_stop call back. during suspend process mac80211
calls drv_stop only when the interface count(local->count) is non-zero.
unfortunately when the network manager is enabled, drv_flush is called
while drv_stop is not called as local->count reaches '0'.
So fix this by simply checking for the device presence in the
drv_flush call back in the driver before queueing work or anything else.
this patch fixes the following WARNING
Call Trace:
[<c014c6e2>] warn_slowpath_common+0x72/0xa0
[<fc133f99>] ? ieee80211_can_queue_work+0x39/0x50 [mac80211]
[<fc133f99>] ? ieee80211_can_queue_work+0x39/0x50 [mac80211]
[<c014c75b>] warn_slowpath_fmt+0x2b/0x30
[<fc133f99>] ieee80211_can_queue_work+0x39/0x50 [mac80211]
[<fc134ed1>] ieee80211_queue_delayed_work+0x21/0x50 [mac80211]
[<fc1e5b22>] ath_tx_complete_poll_work+0xb2/0x100 [ath9k]
[<c016399e>] run_workqueue+0x8e/0x150
[<fc1e5a70>] ? ath_tx_complete_poll_work+0x0/0x100 [ath9k]
[<c0163ae4>] worker_thread+0x84/0xe0
[<c0167a60>] ? autoremove_wake_function+0x0/0x50
[<c0163a60>] ? worker_thread+0x0/0xe0
[<c01677d4>] kthread+0x74/0x80
[<c0167760>] ? kthread+0x0/0x80
[<c0104087>] kernel_thread_helper+0x7/0x10
---[ end trace 2aff81010df9215b ]---
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert logging messages to more current styles.
Added -DDEBUG to Makefile to maintain current message logging.
This could be converted to a specific CONFIG_TULIP_DEBUG option.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the current more descriptive logging styles.
Add pr_fmt and remove PFX where appropriate.
Use netif_<level>, netdev_<level>
Indent a few blocks in xircom_cb where appropriate.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the blocks that are guarded by #if DEBUG to
be #if defined DEBUG && DEBUG > 1 so that pr_debug
can be used later.
Remove enter/leave macros and uses.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support new device OKI SEMICONDUCTOR ML7223 IOH(Input/Output Hub).
The ML7223 IOH is for MP(Media Phone) use.
The ML7223 is companion chip for Intel Atom E6xx series.
The ML7223 is completely compatible for Intel EG20T PCH.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mac_pton() parses MAC address in form XX:XX:XX:XX:XX:XX and only in that form.
mac_pton() doesn't dirty result until it's sure string representation is valid.
mac_pton() doesn't care about characters _after_ last octet,
it's up to caller to deal with it.
mac_pton() diverges from 0/-E return value convention.
Target usage:
if (!mac_pton(str, whatever->mac))
return -EINVAL;
/* ->mac being u8 [ETH_ALEN] is filled at this point. */
/* optionally check str[3 * ETH_ALEN - 1] for termination */
Use mac_pton() in pktgen and netconsole for start.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull read_lock(&bond->lock) and BOND_IS_OK() to bond_start_xmit() from
mode-dependent xmit functions.
netif_running() is always true in hard_start_xmit.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unknown 8168 chips did not have any PLL power method set as they
did not inherit a default family soon enough. Fix it.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
- RTL_GIGA_MAC_NONE is a fake index so put it at the end of the
enumeration and shift everybody.
- RTL_GIGA_MAC_VER_17 / RTL_GIGA_MAC_VER_16 ordering fixed. Though
not wrong it was confusing enough to wonder if things were right.
Renaming rtl_chip_info was not strictly necessary. It allows to
check the patch for the correct use of the indexes though.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Invocation of rtl8169_rx_interrupt from rtl8169_reset_task was originally
intended to retrieve as much packets as possible from the rx ring when a
reset was needed. Nowadays rtl8169_reset_task is only scheduled, with
some delay
a. from the tx timeout watchdog
b. when resuming
c. from rtl8169_rx_interrupt itself
It's dubious that the loss of outdated packets will matter much for a)
and b). c) does not need to call itself again.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
The implementation was a bit krusty.
The 10s rtl8169_phy_timer timer has been (was ?) required with older
8169 for adequate phy operation when full gigabit is advertised in
autonegotiated mode. The timer does nothing if the link is up.
Otherwise it keeps resetting the phy until things improve.
- the device private data field phy_1000_ctrl_reg was used to
schedule the timer. Avoid it and save a few bytes.
- rtl8169_set_settings
pending timer is disabled before changing the link settings as
rtl8169_phy_timer is not always needed (see the removed test in
rtl8169_phy_timer).
- rtl8169_set_speed
the requested link parameters may not match the chipset : bail out
early on failure.
- rtl8169_open
Calling rtl8169_request_timer is redundant with
-> rtl8169_open
-> rtl8169_init_phy
-> rtl8169_set_speed
-> mod_timer
The latter always enables the phy timer whereas the former did not
for RTL_GIGA_MAC_VER_01. It should not make things worse but only
time will tell if reality agrees.
- rtl8169_request_timer : unused yet. Removed.
- rtl8169_delete_timer : useless. Bloat. Removed.
Side effect : the timer may kick in if the TBI is enabled. I do not
know if the TBI has ever been used in real life.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Shorten chipset version test.
No functional change.
Careful readers will notice that the 'supports_gmii' flag is deduced
from the device PCI id. Though less specific than the chipset related
RTL_GIGA_MAC_VER_XY, it is good enough to detect a GMII deprieved 810x.
Some features push for a device specific configuration (improved jumbo
frame support for instance). 'supports_gmii' will follow this path
if / when the device PCI id test stops working.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
The checksum judgment was mistaken.
Judgment result
0:Correct 1:Wrong
This patch fixes the issue.
Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The collision detection setting was invalid.
When collision occurred, because data was not resent,
there was an issue to which a transmitting throughput falls.
This patch enables the collision detection.
Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TTY layer expects 0 if the ldisc->open operation succeeded.
Signed-off-by : Matvejchikov Ilya <matvejchikov@gmail.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed bug to make sure 'pvid' retrieval will work on big endian hosts.
Fixed incorrect comparison between the Rx Completion's 16-bit VLAN TCI
and the PVID. Now comparing only the relevant 12 bits corresponding to
the VID.
Renamed 'vid' field under Rx Completion to 'vlan_tag' to reflect
accurate description.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently EHEA reports to ethtool as supporting 10M, 100M, 1G and
10G and connected to FIBRE independent of the hardware configuration.
However, when connected to FIBRE the only supported speed is 10G
full-duplex, and the other speeds and modes are only supported
when connected to twisted pair.
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Acked-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
veth devices dont use the batched device unregisters yet.
Since veth are a pair of devices, it makes sense to use a batch of two
unregisters, this roughly divides dismantle time by two.
Fix this by changing dellink() callers to always provide a non NULL
head. (Idea from Michał Mirosław)
This patch also handles macvlan case : We now dismantle all macvlans on
top of a lower dev at once.
Reported-by: Alex Bligh <alex@alex.org.uk>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Michał Mirosław <mirqus@gmail.com>
Cc: Jesse Gross <jesse@nicira.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables ethtool to set the loopback mode on a given interface.
By configuring the interface in loopback mode in conjunction with a policy
route / rule, a userland application can stress the egress / ingress path
exposing the flows of the change in progress and potentially help developer(s)
understand the impact of those changes without even sending a packet out
on the network.
Following set of commands illustrates one such example -
a) ip -4 addr add 192.168.1.1/24 dev eth1
b) ip -4 rule add from all iif eth1 lookup 250
c) ip -4 route add local 0/0 dev lo proto kernel scope host table 250
d) arp -Ds 192.168.1.100 eth1
e) arp -Ds 192.168.1.200 eth1
f) sysctl -w net.ipv4.ip_nonlocal_bind=1
g) sysctl -w net.ipv4.conf.all.accept_local=1
# Assuming that the machine has 8 cores
h) taskset 000f netserver -L 192.168.1.200
i) taskset 00f0 netperf -t TCP_CRR -L 192.168.1.100 -H 192.168.1.200 -l 30
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The USB protocol this driver implements appears to require 2 bytes of
padding in front of each received packet. This used to be equal to
the value of NET_IP_ALIGN on x86, so the driver abused that constant
and mostly worked, but this is no longer the case. The driver also
mixed up the URB and packet lengths, resulting in 2 bytes of junk at
the end of the skb.
Introduce a private constant for the 2 bytes of padding; fix this
confusion and check for the under-length case.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rcu callback macvlan_port_rcu_free() just calls a kfree(),
so we use kfree_rcu() instead of the call_rcu(macvlan_port_rcu_free).
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
The rcu callback ring_free_rcu() just calls a kfree(),
so we use kfree_rcu() instead of the call_rcu(ring_free_rcu).
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
I deleted it by mistake in the TX_CHECKSUM removal
commit.
Reported-by: Michał Mirosław <mirqus@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
OS2BMC registers are available for X540.
This patch adds ethtool counters based on those registers.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on patch from Stephen Hemminger.
Convert igb driver to use new set_phys_id ethtool interface.
CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on the original patch from Stephen Hemminger.
Convert to new LED control infrastucture and remove no longer
necessary bits.
CC: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on the original patch from Stephen Hemminger.
Implement set_phys_id to control LED.
CC: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
TX checksumming support has been ifdef commented out of this driver
for more than 10 years, and it makes references to aspects of the IPv4
stack from back then as well.
If someone has one of these rare cards and wants to properly resurrect
TX checksumming support, they can still get at this code in the
version control history.
Signed-off-by: David S. Miller <davem@davemloft.net>
DMA mappings can fail, but the current code
doesn't check for that. Add checking, which
requires some restructuring for proper error
paths.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
All AGN devices need the bytecount table, so
remove the indirection and make the functions
static again.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The device doesn't use the bytecount table for the
command queue, only for aggregation queues to make
aggregation decisions. So don't update it for the
command queue (and we even updated it with wrong
values).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The variable 'len' here is set but never used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The frame pre-allocation is quite a bit of complex
code, all to avoid a single allocation. Remove it
and consolidate the beacon sending code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
There's no need for this, all commands are the right size.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
This patch adds the feature to support the test mode operation through
the generic netlink channel NL80211_CMD_TESTMODE between intel
wireless device iwlwifi and the user space application svtool.
The main purpose is to create a transportation layer between the iwlwifi
device and the user space application so that the interaction between the
user space application svtool and the iwlwifi device in the kernel space is
in a way of generic netlink messaging.
The detail specific functions are:
1. The function iwl_testmode_cmd() is added to digest the svtool test command
from the user space application. The svtool test commands are categorized to
three types : commands to be processed by the device ucode, commands to access
the registers, and commands to be processed at the driver level(such as reload
the ucode). iwl_testmode_cmd() dispatches the commands the corresponding handlers
and reply to user space regarding the command execution status. Extra data is
returned to the user space application if there's any.
2. The function iwl_testmode_ucode_rx_pkt() is added to multicast all the spontaneous
messages from the iwlwifi device to the user space. Regardless the message types,
whenever there is a valid spontaneous message received by the iwlwifi ISR,
iwl_testmode_ucode_rx_pkt() is invoked to multicast the message content to user
space. The message content is not attacked and the message parsing is left to
the user space application.
Implementation guidelines:
1. The generic netlink messaging for iwliwif test mode is through NL80211_CMD_TESTMODE
channel, therefore, the codes need to follow the regulations set by cfg80211.ko
to get the actual device instance ieee80211_ops via cfg80211.ko, so that the iwlwifi
device is indicated with ieee80211_ops and can be actually accessed.
Therefore, a callback iwl_testmode_cmd() is added to the structure
iwlagn_hw_ops in iwl-agn.c.
2. It intends to utilize those low level device access APIs from iwlwifi device driver
(ie. iwlagn.ko) rather than creating it's own set of device access functions.
For example, iwl_send_cmd(), iwl_read32(), iwl_write8(), and iwl_write32() are reused.
3. The main functions are maintained in new files instead of spreading all over the
existing iwlwifi driver files.
The new files added are :
drivers/net/wireless/iwlwifi/iwl-sv-open.c
- to handle the user space test mode application command
and reply the respective command status to the user space application.
- to multicast the spontaneous messages from device to user space.
drivers/net/wireless/iwlwifi/iwl-testmode.h
- the commonly referenced definitions for the TLVs used in
the generic netlink messages
Signed-off-by: Cindy H. Kao <cindy.h.kao@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
WARNING: drivers/net/arm/built-in.o(.data+0x0): Section mismatch in reference from the variable etherh_driver to the function .init.text:etherh_probe()
The variable etherh_driver references
the function __init etherh_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since firmware is capable of generating IV's for all crypto
suits (TKIP, CCMP and WEP), do not ask mac80211 to generate
IV when HW crypto is being used. Instead only reserve
appropriate space in tx skb's in the driver, so that the
firmware can write IV's values.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were performing it on wrong core, it was outdated and is already
implemented in ssb.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were performing it on wrong core, it was outdated and is already
implemented in ssb.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With AR9003 at about ~ 10 feet from an AP that uses RTS / CTS you
will be able to associate but not not get data through given that
the power for the rates used was set too low. This increases the
power and permits data connectivity at longer distances from
access points when connected with HT40. Without this you will not
get any data through when associated to APs configured in HT40
at about more than 10 feet away.
Cc: stable@kernel.org
Cc: Fiona Cain <fcain@atheros.com>
Cc: Zhen Xie <Zhen.Xie@Atheros.com>
Cc: Kathy Giori <kathy.giori@atheros.com>
Cc: Neha Choksi <neha.choksi@atheros.com>
Cc: Wayne Daniel <wayne.daniel@atheros.com>
Cc: Gaurav Jauhar <gaurav.jauhar@atheros.com>
Cc: Samira Naraghi <samira.naraghi@atheros.com>
CC: Ashok Chennupati <ashok.chennupati@atheros.com>
Cc: Lance Zimmerman <lance.zimmerman@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch:
rt2x00: Make rt2x00_queue_entry_for_each more flexible
commit: 10e11568ca
introduced a severe regression on the throughput
for USB hardware. It turns out that the exiting of
the rt2x00queue_for_each_entry() was done too early.
The exact cause for this regression is unknown,
but by disabling the premature exiting of the loop
seems to resolve the issue.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Reported-by: Yasushi SHOJI <yashi@atmark-techno.com>
Reported-by: Balint Viragh <bviragh@dension.com>
Tested-by: Balint Viragh <bviragh@dension.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add necessary RF chipset define and basic support for these devices.
Tested-by: Juan Carlos Garza <juancarlosgarza@gmail.com>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
At present the noise floor calibration is processed in supported
control and extension chains rather than required chains.
Unnccesarily doing nfcal in all supported chains leads to
invalid nf readings on extn chains and these invalid values
got updated into history buffer. While loading those values
from history buffer is moving the chip to deaf state.
This issue was observed in AR9002/AR9003 chips while doing
associate/dissociate in HT40 mode and interface up/down
in iterative manner. After some iterations, the chip was moved
to deaf state. Somehow the pci devices are recovered by poll work
after chip reset. Raading the nf values in all supported extension chains
when the hw is not yet configured in HT40 mode results invalid values.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, the driver only disable multicast filtering when the
FIF_ALLMULTI driver flag has been just set (ie,
if changed_flags& FIF_ALLMULTI and *new_flags& FIF_ALLMULTI) or else
it will reenable multicast filtering.
But next time, this condition will be false and multicast filtering
will be reenabled, even through FIF_ALLMULTI is still set.
This mean that allmulticast only works for less than two minutes in
ad-hoc mode. This patch fixes that to disable multicast filtering
as long as FIF_ALLMULTI is set.
Signed-off-by: Nicolas Cavallari <cavallar@lri.fr>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The WEP key length was being set to 0 erroneously which broke WEP support.
Fix the same by setting the key length appropriately.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Skip initialization of local variables with some default values
if the values are not going to be used further down the code path.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When scan and assoc (infra/ibss) commands are simultaneously
given in two terminals, association response is erroneously
served while serving the scan response.
mwifiex_cfg80211_results() is the common routine for sending
ioctl (scan, assoc etc.) results to cfg80211 stack. In above
scenario even if the common routine is called for scan ioctl
context, it also tries to send information about assoc ioctl to
cfg80211 because "priv->assoc_request/priv->ibss_join_request"
flag is on at that time.
Fix the issue by updating request variable after assoc handling
and modifying the variable check in mwifiex_cfg80211_results.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Modify rtlwifi routines for rtl8192se and set up Kconfig
and Makefile for new driver.
This patch also disables ASPM for the RTL8192SE to prevent some strange
crashes on LF's system.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge routines trx.c and trx.h for RTL8192SE.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge routines table.c and table.h for RTL8192SE.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge routines sw.c and sw.h for RTL8192SE.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge routines rf.c and rf.h for RTL8192SE.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge routines reg.h for RTL8192SE.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge routines phy.c and phy.h for RTL8192SE.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge routines led.c and led.h for RTL8192SE.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge routines hw.c and hw.h for RTL8192SE.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge routines fw.c and fw.h for RTL8192SE. In addition, make changes
to rtlwifi/wifi.h to support RTL8192SE.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge routines dm.c and dm.h for RTL8192SE.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce routine def.h for rtl8192se.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
when aggregation protection mode is enabled the hardware needs
to send RTS/CTS for each HT frame. Currently its disabled so
remove the unused call backs.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As described at http://marc.info/?l=linux-netdev&m=130428493104730&w=2
libertas frequently generates spurious tx timeouts, because the tx
queue is brought down for extended periods during scanning. The net
layer takes a look and incorrectly assumes the queue has been down for
several seconds, and generates a tx_timeout.
One way to fix this is to bump the trans_start counter while scanning
so that the network layer knows that the device is still alive, but
I think the tx_timeout handler is implemented wrongly here and not of
any real use, so I vote to remove it.
As explained at http://marc.info/?l=linux-wireless&m=130430311115755&w=2
the watchdog is primarily meant to deal with lockup on the hardware TX
path (detected by the tx queue being stopped for an extended period of
time), but this is unlikely to happen with libertas. In this case, the tx
queue is stopped only while waiting for lbs_thread to send the queued frame
to the driver, and lbs_thread wakes up the queue immediately after, even
if the frame could not be sent correctly.
So, the only hardware-related possibility that this catches is if
hw_host_to_card hangs - this is something I have never seen. And if it
were to happen, nothing done by lbs_tx_timeout would actually wake up
lbs_thread any quicker than otherwise.
Removing this oddly-behaving spuriously-firing tx_timeout handler should
fix an occasional kernel crash during resume
(http://dev.laptop.org/ticket/10748)
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While draining the txq in flush, the buffers can be
added into the tx queue by tx_tasklet which leads to
unneccesary chip reset.
This issue was originially found with AR9382 and
running heavy uplink udp traffic with higher bandwidth
and doing frequent bgscan.
Cc: stable@kernel.org
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RTR frames do have a valid data length code on CAN.
The driver for SJA1000 did not handle that situation properly.
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Force dev_alloc_name() to be called from register_netdevice() by
dev_get_valid_name(). That allows to remove multiple explicit
dev_alloc_name() calls.
The possibility to call dev_alloc_name in advance remains.
This also fixes veth creation regresion caused by
84c49d8c3e
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid link notification duplication
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reported-by: Karim Hamiti <karim.hamiti@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCIe connections should be expressed as GT/s (GigaTransfers per second)
instead of the current Gb/s (Gigabits per second). In addition, it is
incorrect because (due to PCIe gen 1 & 2 having a 20% overhead) the
actually data rate, when expressed in Gb/s, is only 80% of the rate of
GT/s.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Introduce buffered read/writes which greatly improves performance on
parts with large EEPROMs.
Previously reading/writing a word requires taking/releasing of synchronization
semaphores which adds 10ms to each operation. The optimization is to
read/write in buffers, but make sure the semaphore is not held for >500ms
according to the datasheet.
Since we can't read the EEPROM page size ixgbe_detect_eeprom_page_size() is
used to discover the EEPROM size when needed and keeps the result in
word_page_size for the rest of the run time.
Use buffered reads for ethtool -e.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
warning: symbol 'before' shadows an earlier one
Convert large macros to functions similar to e1000e.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Acked-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Correcting a simple typo with enabling software defined pins. I don't
believe this was causing any issues but this is how it was meant to be
implemented.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change remaining direct calls to function pointers.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This device lies about supporting phys_id. Remove it and just
let the upper layer report not supported.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Recent commits have changed how EEPROM size is checked and if the size
word is misconfigured, the driver will fail to load. This patch adds a
check for invalid size word in the EEPROM and uses default size instead
for 82576 parts.
Reported-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on the original patch sent by Stephen Hemminger.
This version incorporates the ethtool changes that Bruce Allan
submitted.
CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
In function 'e100_hw_init':
warning: 'err' may be used uninitialized in this function
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
stmmac.h uses struct platform_device and doesn't include
<linux/platform_device.h>. Whereas drivers/net/stmmac/stmmac.h includes it, but
doesn't directly use it. And so we get following compilation warning while using
this file:
warning: ‘struct platform_device’ declared inside parameter list
This patch includes <linux/platform_device.h> in linux/stmmac.h and removes it
from drivers/net/stmmac/stmmac.h
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
84c49d8c3e ("veth: remove unneeded
ifname code from veth_newlink()") caused regression on veth
creation. This patch reverts the original one.
Reported-by: Michał Mirosław <mirqus@gmail.com>
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reset loop check should check the MII_BMCR register value for
BMCR_RESET rather than for MII_BMCR (the register address, which also
happens to be zero).
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3 is supposed to enable WoL by default on adapters which support
that, but it fails to do so unless the adapter's
/sys/devices/.../power/wakeup file contains 'enabled' during the
initialization of the adapter. Fix that by making tg3 use
device_set_wakeup_enable() to enable wakeup automatically whenever
WoL should be enabled by default.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds