If no frames has been exchanged with a node for HSR_NODE_FORGET_TIME, the
node will be deleted from the node_db list. If a frame is sent to the node
after it is deleted, a netdev_err message for each slave interface is
produced. This should not happen with dan nodes because of supervision
frames, but can happen often with san nodes, which clutters the kernel
log. Since the hsr protocol does not support sans, this is only relevant
for the prp protocol.
Signed-off-by: Kristian Overskeid <koverskeid@gmail.com>
Link: https://lore.kernel.org/r/20230309092302.179586-1-koverskeid@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
suppress unused warnings and fix the error that there is
with the W=1 enabled.
Warning generated
net/socket.c: In function ‘__sys_getsockopt’:
net/socket.c:2300:13: error: variable ‘max_optlen’ set but not used [-Werror=unused-but-set-variable]
2300 | int max_optlen;
Signed-off-by: Vincenzo Palazzo <vincenzopalazzodev@gmail.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20230310221851.304657-1-vincenzopalazzodev@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Before putting the PHY into IEEE power down mode, disable IRQs to
prevent accessing the PHY once MDIO has already been shutdown.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230310074500.3472858-1-alexander.stein@ew.tq-group.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Lan8841 has 10 GPIOs and it has 2 events(EVENT_A and EVENT_B). It is
possible to assigned the 2 events to any of the GPIOs, but a GPIO can
have only 1 event at a time.
These events are used to generate periodic signals. It is possible to
configure the length, the start time and the period of the signal by
configuring the event.
Currently the SW uses only EVENT_A to generate the perout.
These events are generated by comparing the target time with the PHC
time. In case the PHC time is changed to a value bigger than the target
time + reload time, then it would generate only 1 event and then it
would stop because target time + reload time is small than PHC time.
Therefore it is required to change also the target time every time when
the PHC is changed. The same will apply also when the PHC time is
changed to a smaller value.
This was tested using:
testptp -L 6,2
testptp -p 1000000000 -w 200000000
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20230307214402.793057-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
make versioncheck reports the following:
./drivers/net/ethernet/qlogic/qede/qede.h: 10 linux/version.h not needed.
./drivers/net/ethernet/qlogic/qede/qede_ethtool.c: 7 linux/version.h not needed.
So remove linux/version.h from both of these files. Also remove
linux/compiler.h while at it as it is also not being used.
Signed-off-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230309225206.2473644-1-usama.anjum@collabora.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
EF100 can pop and/or push up to two VLAN tags.
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230309115904.56442-1-edward.cree@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The bindings for the am65-cpsw driver use the name "serdes" to refer to
the Serdes PHY. Thus, update the name used for the Serdes PHY within the
am65_cpsw_init_serdes_phy() function from "serdes-phy" to "serdes".
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Update bindings to include Serdes PHY as an optional PHY, in addition to
the existing CPSW MAC's PHY. The CPSW MAC's PHY is required while the
Serdes PHY is optional. The Serdes PHY handle has to be provided only
when the Serdes is being configured in a Single-Link protocol. Using the
name "serdes-phy" to represent the Serdes PHY handle, the am65-cpsw-nuss
driver can obtain the Serdes PHY and request the Serdes to be
configured.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Flashing firmware via devlink flash was failing on PTP OCP devices
because it is using Quad SPI mode, but the driver was not properly
behaving. With force_irq flag landed it now can be fixed.
Signed-off-by: Vadim Fedorenko <vadfed@meta.com>
Link: https://lore.kernel.org/r/20230309105421.2953451-1-vadfed@meta.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Major changes:
cfg80211
* 6 GHz improvements
* HW timestamping support
* support for randomized auth/deauth TA for PASN privacy
(also for mac80211)
mac80211
* radiotap TLV and EHT support for the iwlwifi sniffer
* HW timestamping support
* per-link debugfs for multi-link
brcmfmac
* support for Apple (M1 Pro/Max) devices
iwlwifi
* support for a few new devices
* EHT sniffer support
rtw88
* better support for some SDIO devices
(e.g. MAC address from efuse)
rtw89
* HW scan support for 8852b
* better support for 6 GHz scanning
-----BEGIN PGP SIGNATURE-----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=sPir
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2023-03-10' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
wireless-next patches for 6.4
Major changes:
cfg80211
* 6 GHz improvements
* HW timestamping support
* support for randomized auth/deauth TA for PASN privacy
(also for mac80211)
mac80211
* radiotap TLV and EHT support for the iwlwifi sniffer
* HW timestamping support
* per-link debugfs for multi-link
brcmfmac
* support for Apple (M1 Pro/Max) devices
iwlwifi
* support for a few new devices
* EHT sniffer support
rtw88
* better support for some SDIO devices
(e.g. MAC address from efuse)
rtw89
* HW scan support for 8852b
* better support for 6 GHz scanning
* tag 'wireless-next-2023-03-10' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (84 commits)
wifi: iwlwifi: mvm: fix EOF bit reporting
wifi: iwlwifi: Do not include radiotap EHT user info if not needed
wifi: iwlwifi: mvm: add EHT RU allocation to radiotap
wifi: iwlwifi: Update logs for yoyo reset sw changes
wifi: iwlwifi: mvm: clean up duplicated defines
wifi: iwlwifi: rs-fw: break out for unsupported bandwidth
wifi: iwlwifi: Add support for B step of BnJ-Fm4
wifi: iwlwifi: mvm: make flush code a bit clearer
wifi: iwlwifi: mvm: avoid UB shift of snif_queue
wifi: iwlwifi: mvm: add primary 80 known for EHT radiotap
wifi: iwlwifi: mvm: parse FW frame metadata for EHT sniffer mode
wifi: iwlwifi: mvm: decode USIG_B1_B7 RU to nl80211 RU width
wifi: iwlwifi: mvm: rename define to generic name
wifi: iwlwifi: mvm: allow Microsoft to use TAS
wifi: iwlwifi: mvm: add all EHT based on data0 info from HW
wifi: iwlwifi: mvm: add EHT radiotap info based on rate_n_flags
wifi: iwlwifi: mvm: add an helper function radiotap TLVs
wifi: radiotap: separate vendor TLV into header/content
wifi: iwlwifi: reduce verbosity of some logging events
wifi: iwlwifi: Adding the code to get RF name for MsP device
...
====================
Link: https://lore.kernel.org/r/20230310120159.36518-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Russell King says:
====================
Rework SFP A2 access conditionals
This series reworks the SFP A2 (diagnostics and control) access so we
don't end up testing a variable number of conditions in several places.
This also resolves a minor issue where we may have a module indicating
that it is not SFF8472 compliant, doesn't implement A2, but fails to
set the enhanced option byte to zero, leading to accesses to the A2
page that fail.
The first patch adds a new flag "have_a2" which indicates whether we
should be accessing the A2 page, and uses this for hwmon. The
conditions are kept the same.
The second patch extends the check for soft-state polling and control
by using this "have_a2" flag (which effectively augments the check to
include some level of SFF8472 compliance.)
====================
Link: https://lore.kernel.org/r/ZAoBnqGBnIZzLwpV@shell.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The soft state bits are stored in the A2h memory space, and require
SFF-8472 compliance. This is what our have_a2 flag tells us, so use
this to indicate whether we should attempt to use the soft signals.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The hwmon code wants to know when it is safe to access the A2h data
stored in a separate address. We indicate that this is present when
we have SFF-8472 compliance and the lack of an address-change
sequence.,
The same conditions are also true if we want to access other controls
and status in the A2h address. So let's make a flag to indicate whether
we can access it, instead of repeating the conditions throughout the
code.
For now, only convert the hwmon code.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Gal Pressman says:
====================
Couple of minor improvements to build_skb variants
First patch replaces open-coded occurrences of
skb_propagate_pfmemalloc() in build_skb() and build_skb_around().
The secnod patch adds a likely() to the skb allocation in build_skb().
====================
Link: https://lore.kernel.org/r/20230308131720.2103611-1-gal@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Similarly to napi_build_skb(), it is likely the skb allocation in
build_skb() succeeded. frag_size != 0 is also likely, as stated in
__build_skb_around().
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use skb_propagate_pfmemalloc() in build_skb()/build_skb_around() instead
of open-coding it.
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The tap driver already supports passing in nonblocking state based
on O_NONBLOCK, add support for checking IOCB_NOWAIT as well. With that
done, we can flag it with FMODE_NOWAIT as well.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Link: https://lore.kernel.org/r/8f859870-e6e2-09ca-9c0f-a2aa7c984fb2@kernel.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
tun already checks for both O_NONBLOCK and IOCB_NOWAIT in its read
and write iter handlers, so it's fully ready for FMODE_NOWAIT. But
for some reason it doesn't set it. Rectify that oversight.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Link: https://lore.kernel.org/r/3f7dc1f0-79ca-d85c-4d16-8c12c5bd492d@kernel.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Horatiu Vultur says:
====================
net: lan966x: Add support for IS1 VCAP
Provide the Ingress Stage 1 (IS1) VCAP (Versatile Content-Aware
Processor) support for the Lan966x platform.
The IS1 VCAP has 3 lookups and they are accessible with a TC chain id:
- chain 1000000: IS1 Lookup 0
- chain 1100000: IS1 Lookup 1
- chain 1200000: IS1 Lookup 2
The IS1 is capable of different actions like rewrite VLAN tags, change
priority of the frames, police the traffic, etc. These features will be
added at a later point.
The IS1 currently implements the action that allows setting the value
of a PAG (Policy Association Group) key field in the frame metadata and
this can be used for matching in an IS2 VCAP rule. In this way a rule in
IS0 VCAP can be linked to rules in the IS2 VCAP. The linking is exposed
by using the TC "goto chain" action with an offset from the IS2 chain ids.
For example "goto chain 8000001" will use a PAG value of 1 to chain to a
rule in IS2 lookup 0.
====================
Link: https://lore.kernel.org/r/20230307220929.834219-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
IS1 VCAP has it's own list of supported ethernet protocol types which is
different than the IS2 VCAP. Therefore separate the list of known
protocol types based on the VCAP type.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allow rules to be chained between IS1 VCAP and IS2 VCAP. Chaining
between IS1 lookups or between IS2 lookups are not supported by the
hardware.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add IS1 VCAP port keyset configuration for lan966x and also update debug
fs support to show the keyset configuration.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Provide IS1 (ingress stage 1) VCAP model for lan966x.
This provides classification actions for lan966x.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
NVMEM layouts are no longer registered early, and thus may not yet be
available when Ethernet drivers (or any other consumer) probe, leading
to possible probe deferrals errors. Forward the error code if this
happens. All other errors being discarded, the driver will eventually
use a random MAC address if no other source was considered valid (no
functional change on this regard).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Marcin Wojtas <mw@semihalf.com>
Link: https://lore.kernel.org/r/20230307192927.512757-1-miquel.raynal@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The filename "wangxun" sorts between "intel" and "xscale", but
xscale/Kconfig contains "Intel XScale" prompts, so Wangxun ends up in the
wrong place in the config front-ends.
Move wangxun/Kconfig so the Wangxun devices appear in order in the user
interface.
Fixes: 3ce7547e5b ("net: txgbe: Add build support for txgbe")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20230307221051.890135-1-helgaas@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-03-07 (igc)
This series contains updates to igc driver only.
Muhammad adds tracking and reporting of QBV config errors.
Tan Tee adds support for configuring max SDU for each Tx queue.
Sasha removes check for alternate media as only one media type is
supported.
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
igc: Clean up and optimize watchdog task
igc: offload queue max SDU from tc-taprio
igc: Add qbv_config_change_errors counter
====================
Link: https://lore.kernel.org/r/20230307221332.3997881-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Florian Westphal says:
====================
Netfilter updates for net-next
1. nf_tables 'brouting' support, from Sriram Yagnaraman.
2. Update bridge netfilter and ovs conntrack helpers to handle
IPv6 Jumbo packets properly, i.e. fetch the packet length
from hop-by-hop extension header, from Xin Long.
This comes with a test BIG TCP test case, added to
tools/testing/selftests/net/.
3. Fix spelling and indentation in conntrack, from Jeremy Sowden.
* 'main' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next:
netfilter: nat: fix indentation of function arguments
netfilter: conntrack: fix typo
selftests: add a selftest for big tcp
netfilter: use nf_ip6_check_hbh_len in nf_ct_skb_network_trim
netfilter: move br_nf_check_hbh_len to utils
netfilter: bridge: move pskb_trim_rcsum out of br_nf_check_hbh_len
netfilter: bridge: check len before accessing more nh data
netfilter: bridge: call pskb_may_pull in br_nf_check_hbh_len
netfilter: bridge: introduce broute meta statement
====================
Link: https://lore.kernel.org/r/20230308193033.13965-1-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
neigh_lookup_nodev isn't used in the kernel after removal
of DECnet. So let's remove it.
Fixes: 1202cdd665 ("Remove DECnet support from kernel")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/eb5656200d7964b2d177a36b77efa3c597d6d72d.1678267343.git.leonro@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since commit 8b41fc4454 ("kbuild: create modules.builtin without
Makefile.modbuiltin or tristate.conf"), MODULE_LICENSE declarations
are used to identify modules. As a consequence, uses of the macro
in non-modules will cause modprobe to misidentify their containing
object file as a module when it is not (false positives), and modprobe
might succeed rather than failing with a suitable error message.
So remove it in the files in this commit, none of which can be built as
modules.
Signed-off-by: Nick Alcock <nick.alcock@oracle.com>
Suggested-by: Luis Chamberlain <mcgrof@kernel.org>
Cc: Hitomi Hasegawa <hasegawa-hitomi@fujitsu.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20230308121230.5354-1-nick.alcock@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since commit 8b41fc4454 ("kbuild: create modules.builtin without
Makefile.modbuiltin or tristate.conf"), MODULE_LICENSE declarations
are used to identify modules. As a consequence, uses of the macro
in non-modules will cause modprobe to misidentify their containing
object file as a module when it is not (false positives), and modprobe
might succeed rather than failing with a suitable error message.
So remove it in the files in this commit, none of which can be built as
modules.
Signed-off-by: Nick Alcock <nick.alcock@oracle.com>
Suggested-by: Luis Chamberlain <mcgrof@kernel.org>
Cc: Hitomi Hasegawa <hasegawa-hitomi@fujitsu.com>
Cc: Jeremy Kerr <jk@codeconstruct.com.au>
Cc: Matt Johnston <matt@codeconstruct.com.au>
Link: https://lore.kernel.org/r/20230308121230.5354-2-nick.alcock@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=XVs0
-----END PGP SIGNATURE-----
Merge tag 'for-linus-2023030901' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID fixes from Benjamin Tissoires:
- fix potential out of bound write of zeroes in HID core with a
specially crafted uhid device (Lee Jones)
- fix potential use-after-free in work function in intel-ish-hid (Reka
Norman)
- selftests config fixes (Benjamin Tissoires)
- few device small fixes and support
* tag 'for-linus-2023030901' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: intel-ish-hid: ipc: Fix potential use-after-free in work function
HID: logitech-hidpp: Add support for Logitech MX Master 3S mouse
HID: cp2112: Fix driver not registering GPIO IRQ chip as threaded
selftest: hid: fix hid_bpf not set in config
HID: uhid: Over-ride the default maximum data buffer value with our own
HID: core: Provide new max_buffer_size attribute to over-ride the default
- Fix systems with memory at end of 32-bit address space,
- Fix initrd on systems where memory does not start at address zero,
- Fix 68030 handling of bus errors for addresses in exception tables.
-----BEGIN PGP SIGNATURE-----
iIsEABYIADMWIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCZAmqMBUcZ2VlcnRAbGlu
dXgtbTY4ay5vcmcACgkQisJQ/WRJ8XAi4AEA2hE4fkPIzobqWXZrLblAYnyy4vIP
S5TeXusdpMahnBEA/36mt2bFZFthHnfvQK/4YjBGDIQPV8+DOIt2YiYFZwIL
=ssyX
-----END PGP SIGNATURE-----
Merge tag 'm68k-for-v6.3-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k fixes from Geert Uytterhoeven:
- Fix systems with memory at end of 32-bit address space
- Fix initrd on systems where memory does not start at address zero
- Fix 68030 handling of bus errors for addresses in exception tables
* tag 'm68k-for-v6.3-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Only force 030 bus error if PC not in exception table
m68k: mm: Move initrd phys_to_virt handling after paging_init()
m68k: mm: Fix systems with memory at end of 32-bit address space
We fetch %SR value from sigframe; it might have been modified by signal
handler, so we can't trust it with any bits that are not modifiable in
user mode.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Rich Felker <dalias@libc.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-03-07 (ice)
This series contains updates to ice driver only.
Dave removes masking from pfcena field as it was incorrectly preventing
valid traffic classes from being enabled.
Michal resolves various smatch issues such as not propagating error
codes and returning 0 explicitly.
Arnd Bergmann resolves gcc-9 warning for integer overflow.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ethernet: ice: avoid gcc-9 integer overflow warning
ice: don't ignore return codes in VSI related code
ice: Fix DSCP PFC TLV creation
====================
Link: https://lore.kernel.org/r/20230307220714.3997294-1-anthony.l.nguyen@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Xin Long says:
====================
sctp: add another two stream schedulers
All SCTP stream schedulers are defined in rfc8260#section-3,
First-Come First-Served, Round-Robin and Priority-Based
Schedulers are already added in kernel.
This patchset adds another two schedulers: Fair Capacity
Scheduler and Weighted Fair Queueing Scheduler.
Note that the left one "Round-Robin Scheduler per Packet"
Scheduler is not implemented by this patch, as it's still
intrusive to be added in the current SCTP kernel code.
====================
Link: https://lore.kernel.org/r/cover.1678224012.git.lucien.xin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
As it says in rfc8260#section-3.6 about the weighted fair queueing
scheduler:
A Weighted Fair Queueing scheduler between the streams is used. The
weight is configurable per outgoing SCTP stream. This scheduler
considers the lengths of the messages of each stream and schedules
them in a specific way to use the capacity according to the given
weights. If the weight of stream S1 is n times the weight of stream
S2, the scheduler should assign to stream S1 n times the capacity it
assigns to stream S2. The details are implementation dependent.
Interleaving user messages allows for a better realization of the
capacity usage according to the given weights.
This patch adds Weighted Fair Queueing Scheduler actually based on
the code of Fair Capacity Scheduler by adding fc_weight into struct
sctp_stream_out_ext and taking it into account when sorting stream->
fc_list in sctp_sched_fc_sched() and sctp_sched_fc_dequeue_done().
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
As it says in rfc8260#section-3.5 about the fair capacity scheduler:
A fair capacity distribution between the streams is used. This
scheduler considers the lengths of the messages of each stream and
schedules them in a specific way to maintain an equal capacity for
all streams. The details are implementation dependent. interleaving
user messages allows for a better realization of the fair capacity
usage.
This patch adds Fair Capacity Scheduler based on the foundations added
by commit 5bbbbe32a4 ("sctp: introduce stream scheduler foundations"):
A fc_list and a fc_length are added into struct sctp_stream_out_ext and
a fc_list is added into struct sctp_stream. In .enqueue, when there are
chunks enqueued into a stream, this stream will be linked into stream->
fc_list by its fc_list ordered by its fc_length. In .dequeue, it always
picks up the 1st skb from stream->fc_list. In .dequeue_done, fc_length
is increased by chunk's len and update its location in stream->fc_list
according to the its new fc_length.
Note that when the new fc_length overflows in .dequeue_done, instead of
resetting all fc_lengths to 0, we only reduced them by U32_MAX / 4 to
avoid a moment of imbalance in the scheduling, as Marcelo suggested.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Russell King says:
====================
Various mtk_eth_soc cleanups
Here are a number of patches that do a bit of cleanup to mtk_eth_soc.
The first patch cleans up mtk_gmac0_rgmii_adjust(), which is the
troublesome function preventing the driver becoming a post-March2020
phylink driver. It doesn't solve that problem, merely makes the code
easier to follow by getting rid of repeated tenary operators.
The second patch moves the check for DDR2 memory to the initialisation
of phylink's supported_interfaces - if TRGMII is not possible for some
reason, we should not be erroring out in phylink MAC operations when
that can be determined prior to phylink creation.
The third patch removes checks from mtk_mac_config() that are done
when initialising supported_interfaces - phylink will not call
mtk_mac_config() with an interface that was not marked as supported,
so these checks are redundant.
The last patch removes the remaining vestiges of REVMII and RMII
support, which appears to be entirely unused.
These shouldn't conflict with Daniel's patch set, but if they do I
will rework as appropriate.
====================
Link: https://lore.kernel.org/r/ZAdj9qUXcHUsK7Gt@shell.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Since the conversion of mtk_eth_soc to phylink's supported_interfaces
bitmap, these two modes have not been selectable. No one has raised
this as an issue. Checking the in-kernel DT files, none of them use
either of these modes with this hardware.
Daniel Golle concurs:
A quick grep through the device trees of the more than 650 ramips and
mediatek boards we support in OpenWrt has revealed that *none* of them
uses either reduced-MII or reverse-MII PHY modes. I could imaging that
some more specialized ramips boards may use the RMII 100M PHY mode to
connect with exotic PHYs for industrial or automotive applications
(think: for 100BASE-T1 PHY connected via RMII). I have never seen or
touched such boards, but there are hints that they do exist.
For reverse-MII there are cases in which the Ralink SoC (Rt305x, for
example) is used in iNIC mode, ie. connected as a PHY to another SoC,
and running only a minimal firmware rather than running Linux. Due to
the lack of external DRAM for the Ralink SoC on this kind of boards,
the Ralink SoC there will anyway never be able to boot Linux.
I've seen this e.g. in multimedia devices like early WiFi-connected
not-yet-so-smart TVs.
Consequently, the conclusion is that no one uses these modes with this
hardware, so we might as well drop support for them.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
mtk_mac_config() checks that the interface mode is permitted for the
capabilities, but we already do these checks in mtk_add_mac() when
initialising phylink's supported_interfaces bitmap. Remove the
unnecessary tests.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Kristian Overskeid