Add support for ranges to the new revision. This doesn't affect
compatibility since the new revision was not released yet.
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TCPMSS target in Xtables should consider the MTU of the reverse
route on forwarded packets as part of the path MTU.
Point in case: IN=ppp0, OUT=eth0. MSS set to 1460 in spite of MTU of
ppp0 being 1392.
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When number of entries exceeds number of initial entries, foo-tables code
will pin table module. But during table unregister on netns stop,
that additional pin was forgotten.
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Propagate netns from userspace.
* arpt_register_table() registers table in supplied netns.
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now it's possible to list and manipulate per-netns ip6tables rules.
Filtering decisions are based on init_net's table so far.
P.S.: remove init_net check in inet6_create() to see the effect
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Propagate netns from userspace down to xt_find_table_lock()
* Register ip6 tables in netns (modules still use init_net)
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now, iptables show and configure different set of rules in different
netnss'. Filtering decisions are still made by consulting only
init_net's set.
Changes are identical except naming so no splitting.
P.S.: one need to remove init_net checks in nf_sockopt.c and inet_create()
to see the effect.
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
.. all the way down to table searching functions.
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Typical table module registers xt_table structure (i.e. packet_filter)
and link it to list during it. We can't use one template for it because
corresponding list_head will become corrupted. We also can't unregister
with template because it wasn't changed at all and thus doesn't know in
which list it is.
So, we duplicate template at the very first step of table registration.
Table modules will save it for use during unregistration time and actual
filtering.
Do it at once to not screw bisection.
P.S.: renaming i.e. packet_filter => __packet_filter is temporary until
full netnsization of table modules is done.
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In fact all we want is per-netns set of rules, however doing that will
unnecessary complicate routines such as ipt_hook()/ipt_do_table, so
make full xt_table array per-netns.
Every user stubbed with init_net for a while.
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch from 0/-E to ptr/PTR_ERR convention.
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the MODULES_DESCRIPTION() tags for all Ebtables modules.
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the xt_conntrack match revision 1 by port matching (all four
{orig,repl}{src,dst}) and by packet direction matching.
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before the removal of the deferred output hooks, netoutdev was used in
case of VLANs on top of a bridge to store the VLAN device, so the
deferred hooks would see the correct output device. This isn't
necessary anymore since we're calling the output hooks for the correct
device directly in the IP stack.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hash table is already initialized by nf_ct_alloc_hashtable().
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
CHECK net/netfilter/nf_conntrack_expect.c
net/netfilter/nf_conntrack_expect.c:429:13: warning: context imbalance in 'exp_seq_start' - wrong count at exit
net/netfilter/nf_conntrack_expect.c:441:13: warning: context imbalance in 'exp_seq_stop' - unexpected unlock
CHECK net/netfilter/nf_log.c
net/netfilter/nf_log.c:105:13: warning: context imbalance in 'seq_start' - wrong count at exit
net/netfilter/nf_log.c:125:13: warning: context imbalance in 'seq_stop' - unexpected unlock
CHECK net/netfilter/nfnetlink_queue.c
net/netfilter/nfnetlink_queue.c:363:7: warning: symbol 'size' shadows an earlier one
net/netfilter/nfnetlink_queue.c:217:9: originally declared here
net/netfilter/nfnetlink_queue.c:847:13: warning: context imbalance in 'seq_start' - wrong count at exit
net/netfilter/nfnetlink_queue.c:859:13: warning: context imbalance in 'seq_stop' - unexpected unlock
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The address of IPv6 raw sockets was shown in the wrong format, from
IPv4 ones. The problem has been introduced by the commit
42a73808ed ("[RAW]: Consolidate proc
interface.")
Thanks to Adrian Bunk who originally noticed the problem.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to use 128 bytes on the stack at all. Clean the code
in the IPv6 style.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different hashtables are used for IPv6 and IPv4 raw sockets, so no
need to check the socket family in the iterator over hashtables. Clean
this out.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
I made a silly typo by entering IPPROTO_IP (== 0) instead of
IPPROTO_IPIP (== 4). This broke the reception of incompressible
packets.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
All but one struct dst_ops static initializations miss explicit
initialization of entries field.
As this field is atomic_t, we should use ATOMIC_INIT(0), and not
rely on atomic_t implementation.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NewReno should add cnt per skb (as with FACK) instead of depending on
SACKED_ACKED bits which won't be set with it at all. Effectively,
NewReno should always exists after the first iteration anyway (or
immediately if there's already head in lost_out.
This was fixed earlier in net-2.6.25 but got reverted among other
stuff and I didn't notice that this is still necessary (actually
wasn't even considering this case while trying to figure out the
reports because I lived with different kind of code than it in reality
was).
This should solve the WARN_ONs in TCP code that as a result of this
triggered multiple times in every place we check for this invariant.
Special thanks to Dave Young <hidave.darkstar@gmail.com> and Krishna
Kumar2 <krkumar2@in.ibm.com> for trying with my debug patches.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Tested-by: Dave Young <hidave.darkstar@gmail.com>
Tested-by: Krishna Kumar2 <krkumar2@in.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The comment about "race free view of the set of network
namespaces" was a bit hasty. Look (there even can be only
one CPU, as discovered by Alexey Dobriyan and Denis Lunev):
put_net()
if (atomic_dec_and_test(&net->refcnt))
/* true */
__put_net(net);
queue_work(...);
/*
* note: the net now has refcnt 0, but still in
* the global list of net namespaces
*/
== re-schedule ==
register_pernet_subsys(&some_ops);
register_pernet_operations(&some_ops);
(*some_ops)->init(net);
/*
* we call netlink_kernel_create() here
* in some places
*/
netlink_kernel_create();
sk_alloc();
get_net(net); /* refcnt = 1 */
/*
* now we drop the net refcount not to
* block the net namespace exit in the
* future (or this can be done on the
* error path)
*/
put_net(sk->sk_net);
if (atomic_dec_and_test(&...))
/*
* true. BOOOM! The net is
* scheduled for release twice
*/
When thinking on this problem, I decided, that getting and
putting the net in init callback is wrong. If some init
callback needs to have a refcount-less reference on the struct
net, _it_ has to be careful himself, rather than relying on
the infrastructure to handle this correctly.
In case of netlink_kernel_create(), the problem is that the
sk_alloc() gets the given namespace, but passing the info
that we don't want to get it inside this call is too heavy.
Instead, I propose to crate the socket inside an init_net
namespace and then re-attach it to the desired one right
after the socket is created.
After doing this, we also have to be careful on error paths
not to drop the reference on the namespace, we didn't get
the one on.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Denis Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing initialization of the new nl_info.nl_net field in
rtm_to_fib6_config(). This will be needed the store network namespace
associated to the fib6_config struct.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
A userspace program may wish to set the mark for each packets its send
without using the netfilter MARK target. Changing the mark can be used
for mark based routing without netfilter or for packet filtering.
It requires CAP_NET_ADMIN capability.
Signed-off-by: Laszlo Attila Toth <panther@balabit.hu>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bluetooth hci_conn sysfs add/del executed in the default
workqueue. If the del_conn is executed after the new add_conn with
same target, add_conn will failed with warning of "same kobject name".
Here add btaddconn & btdelconn workqueues, flush the btdelconn
workqueue in the add_conn function to avoid the issue.
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I moved the nexthdr setting out of IPComp I accidently moved
the reading of ipch->nexthdr after the decompression. Unfortunately
this means that we'd be reading from a stale ipch pointer which
doesn't work very well.
This patch moves the reading up so that we get the correct nexthdr
value.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update fib_trie with some fib_hash fixes:
- check for duplicate alternative routes for prefix+tos+priority when
replacing route
- properly insert by matching tos together with priority
- fix alias walking to use list_for_each_entry_continue for insertion
and deletion when fa_head is not NULL
- copy state from fa to new_fa on replace (not a problem for now)
- additionally, avoid replacement without error if new route is same,
as Joonwoo Park suggests.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
fib_info can be shared by many route prefixes but we don't want
duplicate alternative routes for a prefix+tos+priority. Last change
was not correct to check fib_treeref because it accounts usage from
other prefixes. Additionally, avoid replacement without error if new
route is same, as Joonwoo Park suggests.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix miss of check for report unrecognized HMAC Algorithm
parameter. When AUTH is disabled, goto fall through path to report
unrecognized parameter, else, just break
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: http://bugzilla.kernel.org/show_bug.cgi?id=9825
The inet_diag_lock_handler function uses ERR_PTR to encode errors but
its callers were testing against NULL.
This only happens when the only inet_diag modular user, DCCP, is not
built into the kernel or available as a module.
Also there was a problem with not dropping the mutex lock when a handler
was not found, also fixed in this patch.
This caused an OOPS and ss would then hang on subsequent calls, as
&inet_diag_table_mutex was being left locked.
Thanks to spike at ml.yaroslavl.ru for report it after trying 'ss -d'
on a kernel that doesn't have DCCP available.
This bug was introduced in cset
d523a328fb ("Fix inet_diag dead-lock
regression"), after 2.6.24-rc3, so just 2.6.24 seems to be affected.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ip_fragment has to hit the slow path the value of skb->truesize
may go out of sync because we would have updated it without changing
the packet length. This violates the constraints on truesize.
This patch postpones the update of skb->truesize to prevent this.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
on the last run overlooked that sfuzz triggable message.
move the message to the corresponding comment.
Signed-off-by: maximilian attems <max@stro.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Acked-by: Eric Van Hensbergen <ericvh@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for combined mode algorithms with GCM being
the first algorithm supported.
Combined mode algorithms can be added through the xfrm_user interface
using the new algorithm payload type XFRMA_ALG_AEAD. Each algorithms
is identified by its name and the ICV length.
For the purposes of matching algorithms in xfrm_tmpl structures,
combined mode algorithms occupy the same name space as encryption
algorithms. This is in line with how they are negotiated using IKE.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that ESP uses authenc we can turn on the support for async
algorithms in IPsec.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts ESP to use the crypto_aead interface and in particular
the authenc algorithm. This lays the foundations for future support of
combined mode algorithms.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Teach rfkill about wimax radios.
Had to define a KEY_WIMAX as a 'key for disabling only wimax radios',
as other radio technologies have. This makes sense as hardware has
specific keys for disabling specific radios.
The RFKILL enabling part is, otherwise, a copy and paste of any other
radio technology.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a wrong condition for null qos data frames, causing us to
drop data frames needed for reordering as well.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I introduced the alignment warning I forgot the A-MSDU case which
has a different requirement because each frame contains 14-byte 802.3
headers in front of the IP payload. This patch moves the alignment
warning to a place where we know whether we're dealing with an A-MSDU
frame and adjusts it accordingly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'task_killable' of git://git.kernel.org/pub/scm/linux/kernel/git/willy/misc: (22 commits)
Remove commented-out code copied from NFS
NFS: Switch from intr mount option to TASK_KILLABLE
Add wait_for_completion_killable
Add wait_event_killable
Add schedule_timeout_killable
Use mutex_lock_killable in vfs_readdir
Add mutex_lock_killable
Use lock_page_killable
Add lock_page_killable
Add fatal_signal_pending
Add TASK_WAKEKILL
exit: Use task_is_*
signal: Use task_is_*
sched: Use task_contributes_to_load, TASK_ALL and TASK_NORMAL
ptrace: Use task_is_*
power: Use task_is_*
wait: Use TASK_NORMAL
proc/base.c: Use task_is_*
proc/array.c: Use TASK_REPORT
perfmon: Use task_is_*
...
Fixed up conflicts in NFS/sunrpc manually..
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/selinux-2.6:
security: compile capabilities by default
selinux: make selinux_set_mnt_opts() static
SELinux: Add warning messages on network denial due to error
SELinux: Add network ingress and egress control permission checks
NetLabel: Add auditing to the static labeling mechanism
NetLabel: Introduce static network labels for unlabeled connections
SELinux: Allow NetLabel to directly cache SIDs
SELinux: Enable dynamic enable/disable of the network access checks
SELinux: Better integration between peer labeling subsystems
SELinux: Add a new peer class and permissions to the Flask definitions
SELinux: Add a capabilities bitmap to SELinux policy version 22
SELinux: Add a network node caching mechanism similar to the sel_netif_*() functions
SELinux: Only store the network interface's ifindex
SELinux: Convert the netif code to use ifindex values
NetLabel: Add IP address family information to the netlbl_skbuff_getattr() function
NetLabel: Add secid token support to the NetLabel secattr struct
NetLabel: Consolidate the LSM domain mapping/hashing locks
NetLabel: Cleanup the LSM domain hash functions
NetLabel: Remove unneeded RCU read locks
* git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86: (890 commits)
x86: fix nodemap_size according to nodeid bits
x86: fix overlap between pagetable with bss section
x86: add PCI IDs to k8topology_64.c
x86: fix early_ioremap pagetable ops
x86: use the same pgd_list for PAE and 64-bit
x86: defer cr3 reload when doing pud_clear()
x86: early boot debugging via FireWire (ohci1394_dma=early)
x86: don't special-case pmd allocations as much
x86: shrink some ifdefs in fault.c
x86: ignore spurious faults
x86: remove nx_enabled from fault.c
x86: unify fault_32|64.c
x86: unify fault_32|64.c with ifdefs
x86: unify fault_32|64.c by ifdef'd function bodies
x86: arch/x86/mm/init_32.c printk fixes
x86: arch/x86/mm/init_32.c cleanup
x86: arch/x86/mm/init_64.c printk fixes
x86: unify ioremap
x86: fixes some bugs about EFI memory map handling
x86: use reboot_type on EFI 32
...
We want IPV6HEADER matching for the non-advanced default netfilter
configuration, since it's part of the standard netfilter setup of at
least some distributions (eg Fedora).
Otherwise NETFILTER_ADVANCED loses much of its point, since even
non-advanced users would have to enable all the advanced options just to
get a working IPv6 netfilter setup.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change the following static arrays sized by NR_CPUS to
per_cpu data variables:
char cpu_to_node_map[NR_CPUS];
Signed-off-by: Mike Travis <travis@sgi.com>
Reviewed-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The variable "sin" is a pointer, so sizeof(sin) is the size of a pointer,
not the size of thing that sin points to.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Clean up: Follow recommendations of Chapter 5 of Documentation/CodingStyle
and use "u32" instead of "__u32" for types in definitions that are not
shared with user space.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
rpc_create() can already fill in the hostname with a string representation
of the server's IP address, so remove redundant logic in in
rpcb_getport_sync() that does that.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Clean up: document the rule (kfree) and the exceptions
(RPC_DISPLAY_PROTO and RPC_DISPLAY_NETID) when freeing the objects in
a transport's address_strings array.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Clean up: have the set up routines explicitly pass the strings to be used
for the transport name and NETID. This removes a number of conditionals
and dependencies on rpc_xprt.prot, which is overloaded.
Tighten up type checking on the address_strings array while we're at it.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The gss_pipe_upcall() function expects the copy_to_user() function to
return a negative error value if the call fails, but copy_to_user()
returns an unsigned long number of bytes that couldn't be copied.
Can rpc_pipefs actually retry a partially completed upcall read? If
not, then gss_pipe_upcall() should punt any partial read, just like the
upcall logic in net/sunrpc/cache.c.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
In order to be able to support setting the timeo and retrans parameters on
a per-mountpoint basis, we move the rpc_timeout structure into the
rpc_clnt.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Universal addresses are defined in RFC 1833 and clarified in RFC 3530. We
need to use them in several places in the NFS and RPC clients, so move the
relevant definition and block comment to an appropriate global include
file.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Clean up: use correct type for RPC version numbers in rpcbind client.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Make sure rpcb_clnt passes the correct address length to rpc_create().
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
If the ULP doesn't pass a hostname string to rpc_create(), it manufactures
one based on the passed-in address. Be smart enough to handle an AF_INET6
address properly in this case.
Move the default servername logic before the xprt_create_transport() call
to simplify error handling in rpc_create().
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The two arguments of rpc_depopulate() that pass in inode numbers should use
the same type as inode->i_ino: unsigned long.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The return type of xdr_skb_read_actor functions is size_t. This fixes a
nit I unwittingly overlooked in commit dd456471.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Minor: Replace an empty if statement with a debugging dprintk.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Cc: Thomas Talpey <Thomas.Talpey@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Nit: rl_nchunks is an unsigned integer, so pass it into
rpcrdma_count_chunks() via an unsigned integer argument. This eliminates
a harmless mixed sign comparison in rpcrdma_count_chunks()
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Cc: Thomas Talpey <Thomas.Talpey@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Keep the type of the buffer position the same during iovec conversion to
reduce the likelihood of unexpected results from comparisons and length
computations.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Cc: Thomas Talpey <Thomas.Talpey@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Replace use of rpc_call_setup() with rpc_init_task(), and in cases where we
need to initialise task->tk_action, with rpc_call_start().
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
We want the default scheduling priority (priority == 0) to remain
RPC_PRIORITY_NORMAL.
Also ensure that the priority wait queue scheduling is per process id
instead of sometimes being per thread, and sometimes being per inode.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The sunrpc client exports are not meant to be part of any official kernel
API: they can change at the drop of a hat. Mark them as internal functions
using EXPORT_SYMBOL_GPL.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Add kerneldoc comments for the rpc_pipefs.c functions that are exported.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
If we've disconnected from the server, rather than the other way round,
then it makes little sense to wait 3 seconds before reconnecting.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
xprt_disconnect() should really only be called when the transport shutdown
is completed, and it is time to wake up any pending tasks. Rename it to
xprt_disconnect_done() in order to reflect the semantical change.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Move the calls to xprt_disconnect() over to xprt_force_disconnect() in
order to enable the transport layer to manage the state of the
XPRT_CONNECTED flag.
Ditto in xs_tcp_read_fraghdr().
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The transport layer should do that itself whenever appropriate.
Note that the RDMA transport already assumes that it needs to call
xprt_disconnect in xprt_rdma_close().
For TCP sockets, we want to call xprt_disconnect() only after the
connection has been closed by both ends.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
By using shutdown() rather than close() we allow the RPC client to wait
for the TCP close handshake to complete before we start trying to reconnect
using the same port.
We use shutdown(SHUT_WR) only instead of shutting down both directions,
however we wait until the server has closed the connection on its side.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Add an xprt->state bit to enable the TCP ->state_change() method to signal
whether or not the TCP connection is in the process of closing down.
This will to be used by the reconnection logic in a separate patch.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Currently the TCP rebinding logic assumes that if we're not using a
reserved port, then we don't need to reconnect on the same port if a
disconnection event occurs. This breaks most RPC duplicate reply cache
implementations.
Also take into account the fact that xprt_min_resvport and
xprt_max_resvport may change while we're reconnecting, since the user may
change them at any time via the sysctls. Ensure that we check the port
boundaries every time we loop in xs_bind4/xs_bind6. Also ensure that if the
boundaries change, we only scan the ports a maximum of 2 times.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
When scheduling the autoclose RPC call, we want to ensure that we don't
race against the test_bit() call in xprt_clear_locked().
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
This patch adds auditing support to the NetLabel static labeling mechanism.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
Most trusted OSs, with the exception of Linux, have the ability to specify
static security labels for unlabeled networks. This patch adds this ability to
the NetLabel packet labeling framework.
If the NetLabel subsystem is called to determine the security attributes of an
incoming packet it first checks to see if any recognized NetLabel packet
labeling protocols are in-use on the packet. If none can be found then the
unlabled connection table is queried and based on the packets incoming
interface and address it is matched with a security label as configured by the
administrator using the netlabel_tools package. The matching security label is
returned to the caller just as if the packet was explicitly labeled using a
labeling protocol.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
This patch introduces a mechanism for checking when labeled IPsec or SECMARK
are in use by keeping introducing a configuration reference counter for each
subsystem. In the case of labeled IPsec, whenever a labeled SA or SPD entry
is created the labeled IPsec/XFRM reference count is increased and when the
entry is removed it is decreased. In the case of SECMARK, when a SECMARK
target is created the reference count is increased and later decreased when the
target is removed. These reference counters allow SELinux to quickly determine
if either of these subsystems are enabled.
NetLabel already has a similar mechanism which provides the netlbl_enabled()
function.
This patch also renames the selinux_relabel_packet_permission() function to
selinux_secmark_relabel_packet_permission() as the original name and
description were misleading in that they referenced a single packet label which
is not the case.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
In order to do any sort of IP header inspection of incoming packets we need to
know which address family, AF_INET/AF_INET6/etc., it belongs to and since the
sk_buff structure does not store this information we need to pass along the
address family separate from the packet itself.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
This patch adds support to the NetLabel LSM secattr struct for a secid token
and a type field, paving the way for full LSM/SELinux context support and
"static" or "fallback" labels. In addition, this patch adds a fair amount
of documentation to the core NetLabel structures used as part of the
NetLabel kernel API.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
Currently we use two separate spinlocks to protect both the hash/mapping table
and the default entry. This could be considered a bit foolish because it adds
complexity without offering any real performance advantage. This patch
removes the dedicated default spinlock and protects the default entry with the
hash/mapping table spinlock.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
The NetLabel/LSM domain hash table search function used an argument to specify
if the default entry should be returned if an exact match couldn't be found in
the hash table. This is a bit against the kernel's style so make two separate
functions to represent the separate behaviors.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
This patch removes some unneeded RCU read locks as we can treat the reads as
"safe" even without RCU. It also converts the NetLabel configuration refcount
from a spinlock protected u32 into atomic_t to be more consistent with the rest
of the kernel.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
If an entry is being deleted because it has only one reference,
we immediately delete it and blindly register the rcu handler for it,
This results in oops by double freeing that object.
This patch fixes it by consolidating the code paths for the deletion;
let its rcu handler delete the object if it has no more reference.
Bug was found by Mitsuru Chinen <mitch@linux.vnet.ibm.com>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since fib_route_seq_show now uses hlist_for_each_entry(), the leaf
info can not be NULL.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use nla_nest_start/nla_nest_end for dumping nested attributes.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
nla_parse() returns more detailed errno codes, propagate them back on
error.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert open-coded nlmsg_parse to use the real function.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix two invalid attribute accesses, indices start at 1 with the new
netlink API.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace open coded equivalent of nla_parse_nested_compat().
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix format string warning introduces by the netlink API conversion:
net/sched/sch_atm.c:250: warning: format '%lu' expects type 'long unsigned int', but argument 3 has type 'int'.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
All needed API is done, the namespace is available when required from
the device on the DST entry from the incoming packet. So, just replace
init_net with proper namespace.
Other protocols will follow.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Basically, this piece looks relatively easy. Namespace is already
available on the dst entry via device and the device is safe to
dereferrence. Compare it with one of a searcher and skip entry if
appropriate.
The only exception is ip_rt_frag_needed. So, add namespace parameter to it.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert packet schedulers to use the netlink API. Unfortunately a gradual
conversion is not possible without breaking compilation in the middle or
adding lots of casts, so this patch converts them all in one step. The
patch has been mostly generated automatically with some minor edits to
at least allow seperate conversion of classifiers and actions.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Used to append data to a message without a header or padding.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Additionally remove unnecessary NULL initilizations of the next pointer.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Needed to propagate it down to the ip_route_output_flow.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Needed to propagate it down to the __ip_route_output_key.
Signed_off_by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is only required to propagate it down to the
ip_route_output_slow.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function needs a net namespace to lookup devices, fib tables,
etc. in, so pass it there.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
in_dev_find() need a namespace to pass it to fib_get_table(), so add
an argument.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently fib_select_default calls fib_get_table() with the
init_net. Prepare it to provide a correct namespace to lookup default
route.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The difference in the implementation of the fib_select_default when
CONFIG_IP_MULTIPLE_TABLES is (not) defined looks
negligible. Consolidate it and place into fib_frontend.c.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This converts dumping (and flushing) of large route tables form O(N^2)
to O(N). If the route dump took multiple pages then the dump routine
gets called again. The old code kept track of location by counter, the
new code instead uses the last key.
This is a really big win ( 0.3 sec vs 12 sec) for big route tables.
One side effect is that if the table changes during the dump, then the
last key will not be found, and we will return -EBUSY.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of extra search that made route deletion O(n).
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is easier with TRIE to dump the data traversal rather than
interating over every possible prefix. This saves some time and makes
the dump come out in sorted order.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the complex loop structure of nextleaf() and replace it with a
simpler tree walker. This improves the performance and is much
cleaner.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Match fib_hash, and set NLM_F_MULTI to handle multiple part messages.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code to dump can use the existing hash chain rather than doing
repeated lookup.
Signed-off-by: Stephen Hemminger <stephen.hemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compute the number of prefixes when needed, rather than doing bookeeping.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Style cleanups:
* make check_leaf return -1 or plen, rather than by reference
* Get rid of #ifdef that is always set
* split out embedded function calls in if statements.
* checkpatch warnings
Signed-off-by: Stephen Hemminger <stephen.hemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This improves locality for operations that touch all the leaves. Save
space since these entries don't need to be hardware cache aligned.
Signed-off-by: Stephen Hemminger <stephen.hemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, LMP sets up a 3 seconds timer for discovery.
We don't need it until discovery is set to 1.
Signed-off-by: Ross Burton <ross@openedhand.com>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As event_type_pk_size[] is not used, Remove it.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds static declarations to functions in the Rx flow in order to
eliminate sparse errors
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix last_sample initialization. kzalloc'ing the per-STA data wasn't enough,
as jiffies can assume negative values as well. This fixes a bug which
prevented correct PID operation for a while after booting.
Thanks to Michael Buesch for reporting this.
Reported-and-tested-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit c7a51bda ("mac80211: restructure __ieee80211_rx") extracted
__ieee80211_rx_handle_packet out of __ieee80211_rx and hence changed
the locking rules for __ieee80211_rx_handle_packet(), it is now
invoked under RCU lock. There is, however, one instance left where
it contains an rcu_read_unlock() in an error path, which is a bug.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch assigns correct TID to frames transmitted between
two stations in the same BSS in AP mode.
The problem is that skb->protocol is not set to ETH_P_IP and it is wrong
to use that field at this stage.
The fix compares the LLC/Protocol headers explicitly to check if the
encapsulated frame is IP frame
Signed-off-by: Guy Cohen <guy.cohen@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On x86_64, sizeof(struct rtable) is 0x148, which is rounded up to
0x180 bytes by SLAB allocator.
We can reduce this to exactly 0x140 bytes, without alignment overhead,
and store 12 struct rtable per PAGE instead of 10.
rate_tokens is currently defined as an "unsigned long", while its
content should not exceed 6*HZ. It can safely be converted to an
unsigned int.
Moving tclassid right after rate_tokens to fill the 4 bytes hole
permits to save 8 bytes on 'struct dst_entry', which finally permits
to save 8 bytes on 'struct rtable'
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On namespace start we mainly prepare the ctl variables.
When the namespace is stopped we have to kill all the fragments that
point to this namespace. The inet_frags_exit_net() handles it.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The inet_frags.lru_list is used for evicting only, so we have
to make it per-namespace, to evict only those fragments, who's
namespace exceeded its high threshold, but not the whole hash.
Besides, this helps to avoid long loops in evictor.
The spinlock is not per-namespace because it protects the
hash table as well, which is global.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we have one hashtable to lookup the fragment, having
different secret_interval-s for hash rebuild doesn't make
sense, so move this one to inet_frags.
The inet_frags_ctl becomes empty after this, so remove it.
The appropriate ctl table is kept read-only in namespaces.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the same as with the timeout variable.
Currently, after exceeding the high threshold _all_
the fragments are evicted, but it will be fixed in
later patch.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move it to the netns_frags, adjust the usage and
make the appropriate ctl table writable.
Now fragment, that live in different namespaces can
live for different times.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each namespace has to have own tables to tune their
different parameters, so duplicate the tables and
register them.
All the tables in sub-namespaces are temporarily made
read-only.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is also simple, but introduces more changes, since
then mem counter is altered in more places.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is simple - just move the variable from struct inet_frags
to struct netns_frags and adjust the usage appropriately.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since fragment management code is consolidated, we cannot have the
pointer from inet_frag_queue to struct net, since we must know what
king of fragment this is.
So, I introduce the netns_frags structure. This one is currently
empty, but will be eventually filled with per-namespace
attributes. Each inet_frag_queue is tagged with this one.
The conntrack_reasm is not "netns-izated", so it has one static
netns_frags instance to keep working in init namespace.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a preparation for sysctl netns-ization.
Move the ctl tables to the files, where the tuning
variables reside. Plus make the helpers to register
the tables.
This will simplify the later patches and will keep
similar things closer to each other.
ipv4, ipv6 and conntrack_reasm are patched differently,
but the result is all the tables are in appropriate files.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following sparse warnings:
| net/ipv6/ndisc.c:1300:21: warning: symbol 'opt' shadows an earlier one
| net/ipv6/ndisc.c:1078:7: originally declared here
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Fix the following sparse warning:
| net/ipv6/addrconf.c:3384:2: warning: context imbalance in 'inet6_dump_addr' - different lock contexts for basic block
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Fix the following sparse warnings:
| net/ipv6/route.c:2491:18: warning: symbol 'ipv6_route_sysctl_init' was not declared. Should it be static?
| net/ipv6/icmp.c:922:18: warning: symbol 'ipv6_icmp_sysctl_init' was not declared. Should it be static?
| net/ipv6/reassembly.c:628:6: warning: symbol 'ipv6_frag_sysctl_init' was not declared. Should it be static?
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Fix following sparse warnings:
| net/ipv6/addrlabel.c:172:25: warning: symbol 'ip6addrlbl_alloc' was not declared. Should it be static?
| net/ipv6/addrlabel.c:219:5: warning: symbol '__ip6addrlbl_add' was not declared. Should it be static?
| net/ipv6/addrlabel.c:260:5: warning: symbol 'ip6addrlbl_add' was not declared. Should it be static?
| net/ipv6/addrlabel.c:285:5: warning: symbol '__ip6addrlbl_del' was not declared. Should it be static?
| net/ipv6/addrlabel.c:311:5: warning: symbol 'ip6addrlbl_del' was not declared. Should it be static?
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Fix the following sparse warnings:
| net/ipv6/udplite.c:45:14: warning: symbol 'udplitev6_prot' was not declared. Should it be static?
| net/ipv6/udplite.c:80:12: warning: symbol 'udplitev6_init' was not declared. Should it be static?
| net/ipv6/udplite.c:99:6: warning: symbol 'udplitev6_exit' was not declared. Should it be static?
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
ip_rt_get_source is the infamous place for which dst_ifdown kludges
have been implemented. This means that rt->u.dst.dev can be safely
dereferrenced obtain nd_net.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The packet on the input path always has a referrence to an input
network device it is passed from. Extract network namespace from it.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct network namespace is already used in fib_check_nh. Re-work its
usage for better readability and pass into fib_lookup &
inetdev_by_index.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct network namespace is available inside fib_validate_source. It
can be obtained from the device passed in. The device is not NULL as
in_device is obtained from it just above.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Partial sparse warning fix. The other conditional locking
is too much for sparse to handle.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes a warning print from ieee80211_sta_stop_rx_ba_session
in case the tid is inactive when interface goes down.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds a check to insure that Rx A-MPDU will be stopped only
for the proper device.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before calling update_beacon() mac80211 must
initialize the control.vif pointer so it can
be used by the driver to determine which
interface is trying to send the beacon.
v2: ieee80211_beacon_get() should also initialize the
vif pointer since it can be called by mac80211 internally
before calling config_interface().
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch (based on Ron Rindjunsky's) creates a framework for
a unified way to pass BSS configuration to drivers that require
the information, e.g. for implementing power save mode.
This patch introduces new ieee80211_bss_conf structure that is
passed to the driver via the new bss_info_changed() callback
when the BSS configuration changes.
This new BSS configuration infrastructure adds the following
new features:
* drivers are notified of their association AID
* drivers are notified of association status
and replaces the erp_ie_changed() callback. The patch also does
the relevant driver updates for the latter change.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mattias Nissler's "clean up rate selection" patch incorrectly changes
the behavior of txrate setting in sta_info. This patch backs out parts
of the rate selection consolidation in order to fix this issue for now.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This implements station handling from userspace via cfg80211
in mac80211.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implements the cfg80211 hooks for configuring beaconing
on an access point interface in mac80211. While doing so, it fixes
a number of races that could badly crash the machine when the
beacon is changed while being requested by the driver.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers that support mixed AP/STA operation may well need to
know the type of a virtual interface when iterating over them.
The easiest way to support that is to move the interface type
variable into the vif structure.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch gets rid of the if_id stuff where possible in favour of
a new per-virtual-interface structure "struct ieee80211_vif". This
structure is located at the end of the per-interface structure and
contains a variable length driver-use data area.
This has two advantages:
* removes the need to look up interfaces by if_id, this is better
for working with network namespaces and performance
* allows drivers to store and retrieve per-interface data without
having to allocate own lists/hash tables
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's only a debugging printk, so it went unnoticed; still, the
fix is trivial, so...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The struct ieee8021_auth * passed to it comes straight from skb->data
without any conversions; members of the struct are little-endian, so
we'd better take that into account when doing switch by auth->algorithm,
etc.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
on some codepaths we forgot to convert to little-endian as we do on the
rest of them and as the caller expects from us.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make it match the on-the-wire endianness, eliminate byteswapping.
The only driver that used this sucker (ipw2200) updated.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This short patch modifies the IPv4 networking to enable use of the
240.0.0.0/4 (aka "class-E") address space as propsed in the internet
draft draft-fuller-240space-00.txt.
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
White spaces etc. are changed in gen_replace_estimator() to make it
similar to others in a file.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Classifier code cleanup. Get rid of printk wrapper, and fix whitespace
and other style stuff reported by checkpatch
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ATM scheduler clean house:
* get rid of printk and qdisc_priv() wrapper
* split some assignment in if() statements
* whitespace and line breaks.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jan Engelhardt