The driver refuses to probe with -EINVAL since the commit 5d9814df0a
("clocksource/drivers/dw_apb_timer_of: Add error handling if no clock
available").
Before the driver used to probe successfully if either "clock-freq" or
"clock-frequency" properties has been specified in the device tree.
That commit changed
if (A && B)
panic("No clock nor clock-frequency property");
into
if (!A && !B)
return 0;
That's a bug: the reverse of `A && B` is '!A || !B', not '!A && !B'
Signed-off-by: Vadim V. Vlasov <vadim.vlasov@elpitech.ru>
Signed-off-by: Alexey Sheplyakov <asheplyakov@basealt.ru>
Fixes: 5d9814df0a ("clocksource/drivers/dw_apb_timer_of: Add error handling if no clock available").
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vadim V. Vlasov <vadim.vlasov@elpitech.ru>
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Link: https://lore.kernel.org/r/20211109153401.157491-1-asheplyakov@basealt.ru
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Add calls to disable the clock and unmap the timer base address in case
of any failures.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210322121844.2271041-1-dinguyen@kernel.org
commit ("b0fc70ce1f02 arm64: berlin: Select DW_APB_TIMER_OF") added the
support for the dw_apb_timer into the arm64 defconfig. However, for some
platforms like the Intel Stratix10 and Agilex, the clock manager doesn't
get loaded until after the timer driver get loaded. Thus, the driver hits
the panic "No clock nor clock-frequency property for" because it cannot
properly get the clock.
This patch adds the error handling needed for the timer driver so that
the kernel can continue booting instead of just hitting the panic.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201205105223.208604-1-dinguyen@kernel.org
Commit 1002148899 ("clocksource: dw_apb_timer_of: use
clocksource_of_init") replaced a publicly available driver
initialization method with one called by the timer_probe() method
available after CLKSRC_OF. In current implementation it traverses
all the timers available in the system and calls their initialization
methods if corresponding devices were either in dtb or in acpi. But
if before the commit any number of available timers would be installed
as clockevent and clocksource devices, after that there would be at most
two. The rest are just ignored since default case branch doesn't do
anything. I don't see a reason of such behaviour, neither the commit
message explains it. Moreover this might be wrong if on some platforms
these timers might be used for different purpose, as virtually CPU-local
clockevent timers and as an independent broadcast timer. So in order
to keep the compatibility with the platforms where the order of the
timers detection has some meaning, lets add the secondly discovered
timer to be of clocksource/sched_clock type, while the very first and
the others would provide the clockevents service.
Fixes: 1002148899 ("clocksource: dw_apb_timer_of: use clocksource_of_init")
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-rtc@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200521204818.25436-7-Sergey.Semin@baikalelectronics.ru
Currently any DW APB Timer device detected in OF is bound to CPU #0.
Doing so is redundant since DW APB Timer isn't CPU-local timer, but as
having APB interface is normally accessible from any CPU in the system. By
artificially affiliating the DW timer to the very first CPU we may and in
our case will make the clockevent subsystem to decline the more performant
real CPU-local timers selection in favor of in fact non-local and
accessible over a slow bus - DW APB Timers.
Let's not affiliate the of-detected DW APB Timers to any CPU. By doing so
the clockevent framework would prefer to select the real CPU-local timer
instead of DW APB one. Otherwise if there is no other than DW APB device
for clockevents tracking then it will be selected.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-rtc@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200521204818.25436-6-Sergey.Semin@baikalelectronics.ru
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 503 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190602204653.811534538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add code to retrieve the reset property from the dw-apb timers and if
the property is available, the safe operation is to assert the timer
into reset, and followed by a deassert of the timer reset (brings the
timer out of reset).
This patch is needed for systems where the bootloader has left the timer
not used in reset.
- Trivial conflict with commit a74bd1ad7a:
"Convert to using %pOFn instead of device_node.name"
Reported-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The CLOCKSOURCE_OF_DECLARE macro is used widely for the timers to declare the
clocksource at early stage. However, this macro is also used to initialize
the clockevent if any, or the clockevent only.
It was originally suggested to declare another macro to initialize a
clockevent, so in order to separate the two entities even they belong to the
same IP. This was not accepted because of the impact on the DT where splitting
a clocksource/clockevent definition does not make sense as it is a Linux
concept not a hardware description.
On the other side, the clocksource has not interrupt declared while the
clockevent has, so it is easy from the driver to know if the description is
for a clockevent or a clocksource, IOW it could be implemented at the driver
level.
So instead of dealing with a named clocksource macro, let's use a more generic
one: TIMER_OF_DECLARE.
The patch has not functional changes.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
All the clocksource drivers's init function are now converted to return
an error code. CLOCKSOURCE_OF_DECLARE is no longer used as well as the
clksrc-of table.
Let's convert back the names:
- CLOCKSOURCE_OF_DECLARE_RET => CLOCKSOURCE_OF_DECLARE
- clksrc-of-ret => clksrc-of
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
For exynos_mct and samsung_pwm_timer:
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
For arch/arc:
Acked-by: Vineet Gupta <vgupta@synopsys.com>
For mediatek driver:
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
For the Rockchip-part
Acked-by: Heiko Stuebner <heiko@sntech.de>
For STi :
Acked-by: Patrice Chotard <patrice.chotard@st.com>
For the mps2-timer.c and versatile.c changes:
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
For the OXNAS part :
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
For LPC32xx driver:
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
For Broadcom Kona timer change:
Acked-by: Ray Jui <ray.jui@broadcom.com>
For Sun4i and Sun5i:
Acked-by: Chen-Yu Tsai <wens@csie.org>
For Meson6:
Acked-by: Carlo Caione <carlo@caione.org>
For Keystone:
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
For NPS:
Acked-by: Noam Camus <noamca@mellanox.com>
For bcm2835:
Acked-by: Eric Anholt <eric@anholt.net>
The init functions do not return any error. They behave as the following:
- panic, thus leading to a kernel crash while another timer may work and
make the system boot up correctly
or
- print an error and let the caller unaware if the state of the system
Change that by converting the init functions to return an error conforming
to the CLOCKSOURCE_OF_RET prototype.
Proper error handling (rollback, errno value) will be changed later case
by case, thus this change just return back an error or success in the init
function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Implement an ARM delay timer to be used for udelay(). This allows us to
skip the delay loop calibration at boot on Marvell BG2, BG2Q, BG2CD
platforms. And after this patch, udelay() will be unaffected by CPU
frequency changes.
Note: Although in case there are several possible delay timers, we may
not select the "best" delay timer. Take one Marvell Berlin platform for
example: we have arch timer and dw-apb timer. The arch timer freq is
25MHZ while the dw-apb timer freq is 100MHZ, current selection would
choose the dw-apb timer. But the dw apb timer is on the APB bus while
arch timer sits in CPU, the cost of accessing the apb timer is higher
than the arch timer. We could introduce "rating" concept to delay
timer, but this approach "brings a lot of complexity and workarounds
in the code for a small benefit" as pointed out by Daniel.
Later, Arnd pointed out "However, we could argue that this actually
doesn't matter at all, because the entire point of the ndelay()/
udelay()/mdelay() functions is to waste CPU cycles doing not much at
all, so we can just as well waste them reading the timer register
than spinning on the CPU reading the arch timer more often.", so we
just simply register the dw apb base delay timer.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The dw_apb_timer_of timer is using __raw_readl() to access the
timer register, which is causing issues when the system is
running in big endian mode. Fix this by using readl_relaxed()
which should account for the endian settings.
This fixes issues where the time jumps around in the dmesg
output due to returnling __le32 values.
For an example, these two console lines show time running
backwards:
[ 49.882572] CPU1: failed to come online
[ 43.282457] Brought up 1 CPUs
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Linux ARM Kernel <linux-arm-kernel@lists.infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: digetx@gmail.com
Cc: hdegoede@redhat.com
Cc: laurent.pinchart+renesas@ideasonboard.com
Cc: maxime.ripard@free-electrons.com
Cc: viresh.kumar@linaro.org
Link: http://lkml.kernel.org/r/1427746633-9137-10-git-send-email-daniel.lezcano@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We do not need to trace read_sched_clock function,
so add notrace attribute for this function.
Signed-off-by: Yang Wei <Wei.Yang@windriver.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
In commit 620f5e1cbf (dts: Rename DW APB timer compatible strings), both
"snps,dw-apb-timer-sp" and "snps,dw-apb-timer-osc" were deprecated in place
of "snps,dw-apb-timer". But the driver also needs to be udpated in order to
support this new binding "snps,dw-apb-timer".
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The read_sched_clock should return the ~value because the clock is a
countdown implementation. read_sched_clock() should be the same as
__apbt_read_clocksource().
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
These are all only called by dw_apb_timer_init which is an __init
function, too
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Instead of letting each driver call of_node_put do it centrally in the
loop that also calls the CLOCKSOURCE_OF_DECLARE callbacks. This is less
prone to error and also moves getting and putting the references into the
same function.
Consequently all respective of_node_put calls in drivers are removed.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: David Brown <davidb@codeaurora.org>
The 32 bit sched_clock interface now supports 64 bits. Upgrade to
the 64 bit function to allow us to remove the 32 bit registration
interface.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Pull timer core updates from Thomas Gleixner:
"The timer changes contain:
- posix timer code consolidation and fixes for odd corner cases
- sched_clock implementation moved from ARM to core code to avoid
duplication by other architectures
- alarm timer updates
- clocksource and clockevents unregistration facilities
- clocksource/events support for new hardware
- precise nanoseconds RTC readout (Xen feature)
- generic support for Xen suspend/resume oddities
- the usual lot of fixes and cleanups all over the place
The parts which touch other areas (ARM/XEN) have been coordinated with
the relevant maintainers. Though this results in an handful of
trivial to solve merge conflicts, which we preferred over nasty cross
tree merge dependencies.
The patches which have been committed in the last few days are bug
fixes plus the posix timer lot. The latter was in akpms queue and
next for quite some time; they just got forgotten and Frederic
collected them last minute."
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (59 commits)
hrtimer: Remove unused variable
hrtimers: Move SMP function call to thread context
clocksource: Reselect clocksource when watchdog validated high-res capability
posix-cpu-timers: don't account cpu timer after stopped thread runtime accounting
posix_timers: fix racy timer delta caching on task exit
posix-timers: correctly get dying task time sample in posix_cpu_timer_schedule()
selftests: add basic posix timers selftests
posix_cpu_timers: consolidate expired timers check
posix_cpu_timers: consolidate timer list cleanups
posix_cpu_timer: consolidate expiry time type
tick: Sanitize broadcast control logic
tick: Prevent uncontrolled switch to oneshot mode
tick: Make oneshot broadcast robust vs. CPU offlining
x86: xen: Sync the CMOS RTC as well as the Xen wallclock
x86: xen: Sync the wallclock when the system time is set
timekeeping: Indicate that clock was set in the pvclock gtod notifier
timekeeping: Pass flags instead of multiple bools to timekeeping_update()
xen: Remove clock_was_set() call in the resume path
hrtimers: Support resuming with two or more CPUs online (but stopped)
timer: Fix jiffies wrap behavior of round_jiffies_common()
...
This reverts commit 55a68c23e0.
In order to avoid a collision with dw_apb_timer changes in
the arm-soc tree, revert this change.
I'm leaving it to the arm-soc folks to sort out if they want
to keep the other side of the collision or if they're just going
to back it all out and try again during the next release cycle.
Reported-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Nothing about the sched_clock implementation in the ARM port is
specific to the architecture. Generalize the code so that other
architectures can use it by selecting GENERIC_SCHED_CLOCK.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
[jstultz: Merge minor collisions with other patches in my tree]
Signed-off-by: John Stultz <john.stultz@linaro.org>
dw_apb_timer_init used to search the devicetree for matching timer
devices, making calls to it from board files necessary.
Change the dw_apb_timer_init to work with CLOCKSOURCE_OF_DECLARE.
With this change the function gets called once for each timer node
and tracks these number of calls to attach clockevent and clocksource
devices to the nodes.
Also remove the calls to dw_apb_timer_init from all previous users, as
clocksource_of_init is the default for init_time now.
Tested on the upcoming rk3066 code.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Dinh Nguyen <dinguyen@altera.com>
Add the possibility to get the clock-frequency from a timer clock instead
of specifying it as dt property. Additionally also add the possibility
to also define a controlling periphal clock for the timer block.
The clock-frequency property is kept to act as fallback if no clocks
are specified.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Currently the dw_apb_timer always expects a separate special timer to be
availbable for the sched_clock. Some devices using dw_apb_timers do not
have this sptimer but can use the clocksource as sched_clock instead.
Therefore enable the driver to distiguish between devices with and without
sptimer based on the devicetree data and select the correct timer as
sched_clock.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jamie Iles <jamie@jamieiles.com>
irq_of_parse_and_map() returns 0 on error, while the code checks for NO_IRQ.
This breaks on platforms that have NO_IRQ != 0.
Cc: <stable@vger.kernel.org>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The time.h header seems not to be used by current code.
Removing this include allows the driver to build on other
architecture that do not have this header.
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jamie Iles <jamie@jamieiles.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
[tweaked commit message and header]
Signed-off-by: John Stultz <john.stultz@linaro.org>
It seems we made a mistake when creating dw_apb_timer_of.c:
picoxcell sched_clock had parts that were not related to
dw_apb_timer, yet we moved them to dw_apb_timer_of, and tried to
use them on socfpga.
This results in system where user/system time is not measured
properly, as demonstrated by
time dd if=/dev/urandom of=/dev/zero bs=100000 count=100
So this patch switches sched_clock to hardware that exists on both
platforms, and adds missing of_node_put() in dw_apb_timer_init().
Signed-off-by: Pavel Machek <pavel@denx.de>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Now that the only field in struct sys_timer is .init, delete the struct,
and replace the machine descriptor .timer field with the initialization
function itself.
This will enable moving timer drivers into drivers/clocksource without
having to place a public prototype of each struct sys_timer object into
include/linux; the intent is to create a single of_clocksource_init()
function that determines which timer driver to initialize by scanning
the device dtree, much like the proposed irqchip_init() at:
http://www.spinics.net/lists/arm-kernel/msg203686.html
Includes mach-omap2 fixes from Igor Grinberg.
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Make a common device tree glue for clocksource/dw_apb_timer.
Move mach-picoxcell/time.c to be a generic device tree application
of the dw_apb_timer.
Configure mach-picoxcell to use the dw_apb_timer_of device tree
implementation in drivers/clocksource.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Alexey Sheplyakov