Add new attributes to configure support for multiple BSSID
and advanced multi-BSSID advertisements (EMA) in AP mode.
- NL80211_ATTR_MBSSID_CONFIG used for per interface configuration.
- NL80211_ATTR_MBSSID_ELEMS used to MBSSID elements for beacons.
Memory for the elements is allocated dynamically. This change frees
the memory in existing functions which call nl80211_parse_beacon(),
a comment is added to indicate the new references to do the same.
Signed-off-by: John Crispin <john@phrozen.org>
Co-developed-by: Aloka Dixit <alokad@codeaurora.org>
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Link: https://lore.kernel.org/r/20210916025437.29138-2-alokad@codeaurora.org
[don't leave ERR_PTR hanging around]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a driver FILS crypto offload extended capability flag to indicate
that the driver running in AP mode is capable of handling encryption
and decryption of (Re)Association request and response frames.
Add a command to set FILS AAD data to driver.
This feature is supported on drivers running in AP mode only.
This extended capability is exchanged with hostapd during cfg80211
init. If the driver indicates this capability, then before sending the
Authentication response frame, hostapd sets FILS AAD data to the
driver. This allows the driver to decrypt (Re)Association Request
frame and encrypt (Re)Association Response frame. FILS Key derivation
will still be done in hostapd.
Signed-off-by: Subrat Mishra <subratm@codeaurora.org>
Link: https://lore.kernel.org/r/1631685143-13530-1-git-send-email-subratm@codeaurora.org
[fix whitespace]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds support for BSS color collisions to the wireless subsystem.
Add the required functionality to nl80211 that will notify about color
collisions, triggering the color change and notifying when it is completed.
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/500b3582aec8fe2c42ef46f3117b148cb7cbceb5.1625247619.git.lorenzo@kernel.org
[remove unnecessary NULL initialisation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* aggregation handling improvements for some drivers
* hidden AP discovery on 6 GHz and other HE 6 GHz
improvements
* minstrel improvements for no-ack frames
* deferred rate control for TXQs to improve reaction
times
* virtual time-based airtime scheduler
* along with various little cleanups/fixups
-----BEGIN PGP SIGNATURE-----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=nFvj
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2021-06-25' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes berg says:
====================
Lots of changes:
* aggregation handling improvements for some drivers
* hidden AP discovery on 6 GHz and other HE 6 GHz
improvements
* minstrel improvements for no-ack frames
* deferred rate control for TXQs to improve reaction
times
* virtual time-based airtime scheduler
* along with various little cleanups/fixups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add wiphy_info_once() helper that prints info message only once.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210511211549.30571-1-digetx@gmail.com
There may be cases where vendor-specific elements need to be
used over the air. Rather than have driver or firmware add
them and possibly cause problems that way, add them to the
iftype-data band capabilities. This way we can advertise to
userspace first, and use them in mac80211 next.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210618133832.e8c4f0347276.Iee5964682b3e9ec51fc1cd57a7c62383eaf6ddd7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The htmldoc produces this warning which was introduced
bu the commit below.
include/net/cfg80211.h:6643: warning: expecting prototype for wiphy_rfkill_set_hw_state().
Prototype was for wiphy_rfkill_set_hw_state_reason() instead
Fixes: 6f779a66dc ("cfg80211: allow specifying a reason for hw_rfkill")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://lore.kernel.org/r/20210413113850.59098-1-emmanuel.grumbach@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
rfkill now allows to report a reason for the hw_rfkill state.
Allow cfg80211 drivers to specify this reason.
Keep the current API to use the default reason
(RFKILL_HARD_BLOCK_SIGNAL).
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://lore.kernel.org/r/20210322204633.102581-4-emmanuel.grumbach@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If register_netdevice() fails after having called cfg80211's
netdev notifier (cfg80211_netdev_notifier_call) it will call
the notifier again with UNREGISTER. This would then lock the
wiphy mutex because we're marked as registered, which causes
a deadlock.
Fix this by separately keeping track of whether or not we're
in the middle of registering to also skip the notifier call
on this unregister.
Reported-by: syzbot+2ae0ca9d7737ad1a62b7@syzkaller.appspotmail.com
Fixes: a05829a722 ("cfg80211: avoid holding the RTNL when calling the driver")
Link: https://lore.kernel.org/r/20210201192048.ed8bad436737.I7cae042c44b15f80919a285799a15df467e9d42d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, _everything_ in cfg80211 holds the RTNL, and if you
have a slow USB device (or a few) you can get some bad lock
contention on that.
Fix that by re-adding a mutex to each wiphy/rdev as we had at
some point, so we have locking for the wireless_dev lists and
all the other things in there, and also so that drivers still
don't have to worry too much about it (they still won't get
parallel calls for a single device).
Then, we can restrict the RTNL to a few cases where we add or
remove interfaces and really need the added protection. Some
of the global list management still also uses the RTNL, since
we need to have it anyway for netdev management, but we only
hold the RTNL for very short periods of time here.
Link: https://lore.kernel.org/r/20210122161942.81df9f5e047a.I4a8e1a60b18863ea8c5e6d3a0faeafb2d45b2f40@changeid
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> [marvell driver issues]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We used to not require anything in terms of registering netdevs
with cfg80211, using a netdev notifier instead. However, in the
next patch reducing RTNL locking, this causes big problems, and
the simplest way is to just require drivers to do things better.
Change the registration/unregistration semantics to require the
drivers to call cfg80211_(un)register_netdevice() when this is
happening due to a cfg80211 request, i.e. add_virtual_intf() or
del_virtual_intf() (or if it somehow has to happen in any other
cfg80211 callback).
Otherwise, in other contexts, drivers may continue to use the
normal netdev (un)registration functions as usual.
Internally, we still use the netdev notifier and track (by the
new wdev->registered bool) if the wdev had already been added
to cfg80211 or not.
Link: https://lore.kernel.org/r/20210122161942.cf2f4b65e4e9.Ida8234e50da13eb675b557bac52a713ad4eddf71@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current phyrate conversion does not include extended MCS and provides
incorrect rates. Add a flag for extended MCS in DMG and add corresponding
phyrate table for the correct conversions using base MCS in DMG specs.
Signed-off-by: Max Chen <mxchen@codeaurora.org>
Link: https://lore.kernel.org/r/1609977050-7089-2-git-send-email-mxchen@codeaurora.org
[reduce data size, make a single WARN]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A function has a different name between their prototype
and its kernel-doc markup:
../include/net/cfg80211.h:1766: warning: expecting prototype for struct cfg80211_sar_chan_ranges. Prototype was for struct cfg80211_sar_freq_ranges instead
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/c7ed4bc4d9e992ead16d3d2df246f3b56dbfb1fb.1610610937.git.mchehab+huawei@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A stray @ caused the kernel-doc parser to not understand
this, fix that. Also add some missing kernel-doc.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes: 6bdb68cef7 ("nl80211: add common API to configure SAR power limitations")
Fixes: c534e093d8 ("mac80211: add ieee80211_set_sar_specs")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Stephen Rothwell <sfr@canb.auug.org.au> # build only
Link: https://lore.kernel.org/r/20210106234740.96827c18f9bd.I8b9f0a9cbfe186931ef9640046f414371f216914@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
NL80211_CMD_SET_SAR_SPECS is added to configure SAR from
user space. NL80211_ATTR_SAR_SPEC is used to pass the SAR
power specification when used with NL80211_CMD_SET_SAR_SPECS.
Wireless driver needs to register SAR type, supported frequency
ranges to wiphy, so user space can query it. The index in
frequency range is used to specify which sub band the power
limitation applies to. The SAR type is for compatibility, so later
other SAR mechanism can be implemented without breaking the user
space SAR applications.
Normal process is user space queries the SAR capability, and
gets the index of supported frequency ranges and associates the
power limitation with this index and sends to kernel.
Here is an example of message send to kernel:
8c 00 00 00 08 00 01 00 00 00 00 00 38 00 2b 81
08 00 01 00 00 00 00 00 2c 00 02 80 14 00 00 80
08 00 02 00 00 00 00 00 08 00 01 00 38 00 00 00
14 00 01 80 08 00 02 00 01 00 00 00 08 00 01 00
48 00 00 00
NL80211_CMD_SET_SAR_SPECS: 0x8c
NL80211_ATTR_WIPHY: 0x01(phy idx is 0)
NL80211_ATTR_SAR_SPEC: 0x812b (NLA_NESTED)
NL80211_SAR_ATTR_TYPE: 0x00 (NL80211_SAR_TYPE_POWER)
NL80211_SAR_ATTR_SPECS: 0x8002 (NLA_NESTED)
freq range 0 power: 0x38 in 0.25dbm unit (14dbm)
freq range 1 power: 0x48 in 0.25dbm unit (18dbm)
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Abhishek Kumar <kuabhs@chromium.org>
Link: https://lore.kernel.org/r/20201203103728.3034-2-cjhuang@codeaurora.org
[minor edits, NLA parse cleanups]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We don't really use this struct, we're now using
struct cfg80211_he_bss_color instead.
Change the one place in mac80211 that's using the old
name to use struct assignment instead of memcpy() and
thus remove the wrong sizeof while at it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201206145305.f6698d97ae4e.Iba2dffcb79c4ab80bde7407609806010b55edfdf@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
linux/netdevice.h is included in very many places, touching any
of its dependecies causes large incremental builds.
Drop the linux/ethtool.h include, linux/netdevice.h just needs
a forward declaration of struct ethtool_ops.
Fix all the places which made use of this implicit include.
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Shannon Nelson <snelson@pensando.io>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20201120225052.1427503-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* injection/radiotap updates for new test capabilities
* remove WDS support - even years ago when we turned
it off by default it was already basically unusable
* support for HE (802.11ax) rates for beacons
* support for some vendor-specific HE rates
* many other small features/cleanups
-----BEGIN PGP SIGNATURE-----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=TGgF
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2020-11-13' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Some updates:
* injection/radiotap updates for new test capabilities
* remove WDS support - even years ago when we turned
it off by default it was already basically unusable
* support for HE (802.11ax) rates for beacons
* support for some vendor-specific HE rates
* many other small features/cleanups
* tag 'mac80211-next-for-net-next-2020-11-13' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next: (21 commits)
nl80211: fix kernel-doc warning in the new SAE attribute
cfg80211: remove WDS code
mac80211: remove WDS-related code
rt2x00: remove WDS code
b43legacy: remove WDS code
b43: remove WDS code
carl9170: remove WDS code
ath9k: remove WDS code
wireless: remove CONFIG_WIRELESS_WDS
mac80211: assure that certain drivers adhere to DONT_REORDER flag
mac80211: don't overwrite QoS TID of injected frames
mac80211: adhere to Tx control flag that prevents frame reordering
mac80211: add radiotap flag to assure frames are not reordered
mac80211: save HE oper info in BSS config for mesh
cfg80211: add support to configure HE MCS for beacon rate
nl80211: fix beacon tx rate mask validation
nl80211/cfg80211: fix potential infinite loop
cfg80211: Add support to calculate and report 4096-QAM HE rates
cfg80211: Add support to configure SAE PWE value to drivers
ieee80211: Add definition for WFA DPP
...
====================
Link: https://lore.kernel.org/r/20201113101148.25268-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support to configure SAE PWE preference from userspace to drivers in
both AP and STA modes. This is needed for cases where the driver takes
care of Authentication frame processing (SME in the driver) so that
correct enforcement of the acceptable PWE derivation mechanism can be
performed.
The userspace applications can pass the sae_pwe value using the
NL80211_ATTR_SAE_PWE attribute in the NL80211_CMD_CONNECT and
NL80211_CMD_START_AP commands to the driver. This allows selection
between the hunting-and-pecking loop and hash-to-element options for PWE
derivation. For backwards compatibility, this new attribute is optional
and if not included, the driver is notified of the value being
unspecified.
Signed-off-by: Rohan Dutta <drohan@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20201027100910.22283-1-jouni@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some identifiers have different names between their prototypes
and the kernel-doc markup.
Others need to be fixed, as kernel-doc markups should use this format:
identifier - description
In the specific case of __sta_info_flush(), add a documentation
for sta_info_flush(), as this one is the one used outside
sta_info.c.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Link: https://lore.kernel.org/r/978d35eef2dc76e21c81931804e4eaefbd6d635e.1603469755.git.mchehab+huawei@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE+QmuaPwR3wnBdVwACF8+vY7k4RUFAl+JNGYACgkQCF8+vY7k
4RV/TA//ZoRoMQE5B6zwO4kOGILMbmW2uepjoEysLgus2ctkTUoRkpNLWS3SozcU
6c/eW1rC4Fji24te6lwusciZa5zQgbGMjFYk1LhnJ65lJA+kQ+kV1DGz/ZWtklMM
gLX20+tQADqGl+u2dmFCvmRhPWJ9nzt1C0auN7dGeu+9g97GnhKG6o2Kv/nVCb68
qMmAs9UrfN24DO5G1ixkdY08nSNJPrpgQnIR2ruUysUII/yTTtcnmHDbH3WWL6+9
2P87AZ6zsa3FdBhAjmG5YJklQgPkLFWEykHMTqq/Mkcpff/JB/AayrL6XNB2QoZb
YXLHJp3Na6iBmdmHhecg+VQDgz28UfMk+p+HFoJh8RTtJa9/qJvYdJmIE/mUPrnY
gL4jNgMVwkptGHXh7IRuSLysT5heJPMQss6TfZ6yYadeOIpx7W8MCAYnGffiElLQ
hmKdmyCszS3SERJz40EOBdr2NQYcDEUt2NtEhdVfium21A4PFOdJlCejifGhJyzP
n1QcyMXHnh/d4zecA6fcD0LVyxBgngeKEvdtOLZJ1ubxWwHhgWTN8R4HedoN2Nb9
cLEUK8Td+9n2RVS8UED4BBI+6vfN3Y6Syjvy8qD3pCs4SBcu3k790mf47t2QhkEq
+Ho06gdrGJdEcSDO8zVY7qjZX/GX/dbRHCb5CRokL5FmNWhXd/Y=
=26wi
-----END PGP SIGNATURE-----
Merge tag 'docs/v5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull documentation updates from Mauro Carvalho Chehab:
"A series of patches addressing warnings produced by make htmldocs.
This includes:
- kernel-doc markup fixes
- ReST fixes
- Updates at the build system in order to support newer versions of
the docs build toolchain (Sphinx)
After this series, the number of html build warnings should reduce
significantly, and building with Sphinx 3.1 or later should now be
supported (although it is still recommended to use Sphinx 2.4.4).
As agreed with Jon, I should be sending you a late pull request by the
end of the merge window addressing remaining issues with docs build,
as there are a number of warning fixes that depends on pull requests
that should be happening along the merge window.
The end goal is to have a clean htmldocs build on Kernel 5.10.
PS. It should be noticed that Sphinx 3.0 is not currently supported,
as it lacks support for C domain namespaces. Such feature, needed in
order to document uAPI system calls with Sphinx 3.x, was added only on
Sphinx 3.1"
* tag 'docs/v5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (75 commits)
PM / devfreq: remove a duplicated kernel-doc markup
mm/doc: fix a literal block markup
workqueue: fix a kernel-doc warning
docs: virt: user_mode_linux_howto_v2.rst: fix a literal block markup
Input: sparse-keymap: add a description for @sw
rcu/tree: docs: document bkvcache new members at struct kfree_rcu_cpu
nl80211: docs: add a description for s1g_cap parameter
usb: docs: document altmode register/unregister functions
kunit: test.h: fix a bad kernel-doc markup
drivers: core: fix kernel-doc markup for dev_err_probe()
docs: bio: fix a kerneldoc markup
kunit: test.h: solve kernel-doc warnings
block: bio: fix a warning at the kernel-doc markups
docs: powerpc: syscall64-abi.rst: fix a malformed table
drivers: net: hamradio: fix document location
net: appletalk: Kconfig: Fix docs location
dt-bindings: fix references to files converted to yaml
memblock: get rid of a :c:type leftover
math64.h: kernel-docs: Convert some markups into normal comments
media: uAPI: buffer.rst: remove a left-over documentation
...
Changeset df78a0c0b6 ("nl80211: S1G band and channel definitions")
added a new parameter, but didn't add the corresponding kernel-doc
markup, as repoted when doing "make htmldocs":
./include/net/cfg80211.h:471: warning: Function parameter or member 's1g_cap' not described in 'ieee80211_supported_band'
Add a documentation for it.
Fixes: df78a0c0b6 ("nl80211: S1G band and channel definitions")
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
NL80211_ATTR_S1G_CAPABILITY can be passed along with
NL80211_ATTR_S1G_CAPABILITY_MASK to NL80211_CMD_ASSOCIATE
to indicate S1G capabilities which should override the
hardware capabilities in eg. the association request.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-4-thomas@adapt-ip.com
[johannes: always require both attributes together, commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Support 6 GHz scanning, by
* a new scan flag to scan for colocated BSSes advertised
by (and found) APs on 2.4 & 5 GHz
* doing the necessary reduced neighbor report parsing for
this, to find them
* adding the ability to split the scan request in case the
device by itself cannot support this.
Also add some necessary bits in mac80211 to not break with
these changes.
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20200918113313.232917c93af9.Ida22f0212f9122f47094d81659e879a50434a6a2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds new attributes to support unsolicited broadcast
probe response transmission used for in-band
discovery in 6GHz band (IEEE P802.11ax/D6.0 26.17.2.3.2, AP behavior for
fast passive scanning).
The new attribute, NL80211_ATTR_UNSOL_BCAST_PROBE_RESP, is nested which
supports following parameters:
(1) NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_INT - Packet interval
(2) NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_TMPL - Template data
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Link: https://lore.kernel.org/r/010101747a946698-aac263ae-2ed3-4dab-9590-0bc7131214e1-000000@us-west-2.amazonses.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
S1G channels have a single width defined per frequency, so
derive it from the channel flags with
ieee80211_s1g_channel_width().
Also support setting an S1G channel where control frequency may
differ from operating, and add some basic validation to
ensure the control channel is with the operating.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200908190323.15814-6-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
S1G supports 5 channel widths: 1, 2, 4, 8, and 16. One
channel width is allowed per frequency in each operating
class, so it makes more sense to advertise the specific
channel width allowed.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200908190323.15814-3-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The value of struct bss_parameters::ap_isolate will be -1, 0 or 1.
The value -1 means not to change. To prevent developers from thinking
ap_isolate is only 0 or 1, I add more comments on it.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Reviewed-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200908060157.98846-1-wright.feng@cypress.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds the nl80211 structs, definitions, policies and parsing
code required to pass fixed HE rate, GI and LTF settings.
Signed-off-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20200804081630.2013619-1-john@phrozen.org
[fix comment]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is in fact 'disabled' in the spec, but there it's in a
place where that actually makes sense. In our internal data
structures, it doesn't really make sense, and in fact the
previous commit just fixed a bug in that area.
Make this safer by inverting the polarity from 'disabled' to
'enabled'.
Link: https://lore.kernel.org/r/20200730130051.5d8399545bd9.Ie62fdcd1a6cd9c969315bc124084a494ca6c8df3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Besides information about num of peerings and gate connectivity,
the mesh formation byte also contains a flag for authentication
server connectivity, that currently cannot be set in the mesh conf.
This patch adds this capability, which is necessary to implement
802.1X authentication in mesh mode.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20200611140238.427461-1-markus.theil@tu-ilmenau.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, before being able to forward a packet between two 802.11s
nodes, both a PLINK handshake is performed upon receiving a beacon and
then later a PREQ/PREP exchange for path discovery is performed on
demand upon receiving a data frame to forward.
When running a mesh protocol on top of an 802.11s interface, like
batman-adv, we do not need the multi-hop mesh routing capabilities of
802.11s and usually set mesh_fwding=0. However, even with mesh_fwding=0
the PREQ/PREP path discovery is still performed on demand. Even though
in this scenario the next hop PREQ/PREP will determine is always the
direct 11s neighbor node.
The new mesh_nolearn parameter allows to skip the PREQ/PREP exchange in
this scenario, leading to a reduced delay, reduced packet buffering and
simplifies HWMP in general.
mesh_nolearn is still rather conservative in that if the packet destination
is not a direct 11s neighbor, it will fall back to PREQ/PREP path
discovery.
For normal, multi-hop 802.11s mesh routing it is usually not advisable
to enable mesh_nolearn as a transmission to a direct but distant neighbor
might be worse than reaching that same node via a more robust /
higher throughput etc. multi-hop path.
Cc: Sven Eckelmann <sven@narfation.org>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Linus Lüssing <ll@simonwunderlich.de>
Link: https://lore.kernel.org/r/20200617073034.26149-1-linus.luessing@c0d3.blue
[fix nl80211 policy to range 0/1 only]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The low level driver adds its own opaque information
in the BSS table in the cfg80211_bss structure.
The low level driver may need to signal that this information
is no longer relevant and needs to be recreated.
Add an API to allow the low level driver to do that.
iwlwifi needs this because it keeps there an information about
the firmware's internal clock. This is kept in mac80211's
struct ieee80211_bss::sync_device_ts.
This information is populated while we scan, we add the
internal firmware's clock to each beacon which allows us to
program the firmware correctly after association so that
it'll know when (in terms of its internal clock) the DTIM
and TBTT will happen.
When the firmware is reset this internal clock is reset as
well and ieee80211_bss::sync_device_ts is no longer accurate.
iwlwifi will call this new API any time the firmware is started.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://lore.kernel.org/r/20200625111524.3992-1-emmanuel.grumbach@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Lockdep reports that we may deadlock because we take the RTNL on
the work struct, but flush it under RTNL. Clearly, it's correct.
In practice, this can happen when doing rfkill on an active device.
Fix this by moving the work struct to the wiphy (registered dev)
layer, and iterate over all the wdevs inside there. This then
means we need to track which one of them has work to do, so we
don't update to the driver for all wdevs all the time.
Also fix a locking bug I noticed while working on this - the
registrations list is iterated as if it was an RCU list, but it
isn't handle that way - and we need to lock now for the update
flag anyway, so remove the RCU.
Fixes: 6cd536fe62 ("cfg80211: change internal management frame registration API")
Reported-by: Markus Theil <markus.theil@tu-ilmenau.de>
Reported-and-tested-by: Kenneth R. Crudup <kenny@panix.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20200604120420.b1dc540a7e26.I55dcca56bb5bdc5d7ad66a36a0b42afd7034d8be@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With some newer AKMs, the KCK and KEK are bigger, so allow that
if the driver advertises support for it. In addition, add a new
attribute for the AKM so we can use it for offloaded rekeying.
Signed-off-by: Nathan Errera <nathan.errera@intel.com>
[reword commit message]
Link: https://lore.kernel.org/r/20200528212237.5eb58b00a5d1.I61b09d77c4f382e8d58a05dcca78096e99a6bc15@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These capabilities cover what would otherwise be transported
in HT/VHT capabilities, but only a subset thereof that is
actually needed on 6 GHz with HE already present. Expose the
capabilities to userspace, drivers are expected to set them
as using the 6 GHz band (currently) requires HE capability.
Link: https://lore.kernel.org/r/20200528213443.244cd5cb9db8.Icd8c773277a88c837e7e3af1d4d1013cc3b66543@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds support to configure per TID Tx Rate configuration
through NL80211_TID_CONFIG_ATTR_TX_RATE* attributes. And it uses
nl80211_parse_tx_bitrate_mask api to validate the Tx rate mask.
Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Link: https://lore.kernel.org/r/1589357504-10175-1-git-send-email-tamizhr@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds the necessary capabilities in nl80211 to allow drivers to
assign a cookie to control port TX frames (returned via extack in
the netlink ACK message of the command) and then later report the
frame's status.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20200508144202.7678-2-markus.theil@tu-ilmenau.de
[use extack cookie instead of explicit message, recombine patches]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20200507183909.GA12993@embeddedor
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers may wish to report the RX frequency in units of
KHz. Provide cfg80211_rx_mgmt_khz() and wrap it with
cfg80211_rx_mgmt() so exisiting drivers which can't report
KHz anyway don't need to change. Add a similar wrapper for
cfg80211_report_obss_beacon() so the frequency units stay
somewhat consistent.
This doesn't actually change the nl80211 API yet.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200430172554.18383-2-thomas@adapt-ip.com
[fix mac80211 calling the non-khz version of obss beacon report,
drop trace point name changes]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
TIDs mask type is u64 in wiphy settings and nl80211 processing, see:
- wiphy TIDs mask sizes in tid_config_support structure
- prepare driver command in parse_tid_conf
Use the same type for TIDs mask in cfg80211_tid_cfg.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20200424112905.26770-2-sergey.matyukevich.os@quantenna.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* hwsim improvements from Jouni and myself, to be able to
test more scenarios easily
* some more HE (802.11ax) support
* some initial S1G (sub 1 GHz) work for fractional MHz channels
* some (action) frame registration updates to help DPP support
* along with other various improvements/fixes
-----BEGIN PGP SIGNATURE-----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=MVBJ
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2020-04-25' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
One batch of changes, containing:
* hwsim improvements from Jouni and myself, to be able to
test more scenarios easily
* some more HE (802.11ax) support
* some initial S1G (sub 1 GHz) work for fractional MHz channels
* some (action) frame registration updates to help DPP support
* along with other various improvements/fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- adjust title markup;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some bands (S1G) define channels centered on a non-integer
MHz. Give ieee80211_channel and cfg80211_chan_def a
freq_offset component where the final frequency can be
expressed as:
MHZ_TO_KHZ(chan->center_freq) + chan->freq_offset;
Also provide some helper functions to do the frequency
conversion and test for equality.
Retain the existing interface to frequency and channel
conversion helpers, and expose new ones which handle
frequencies in units of KHz.
Some internal functions (net/wireless/chan.c) pass around
a frequency value. Convert these to units of KHz.
mesh, ibss, wext, etc. are currently ignored.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200402011810.22947-3-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For DPP, there's a need to receive multicast action frames,
but many drivers need a special filter configuration for this.
Support announcing from userspace in the management registration
that multicast RX is required, with an extended feature flag if
the driver handles this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20200417124013.c46238801048.Ib041d437ce0bff28a0c6d5dc915f68f1d8591002@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Almost all drivers below cfg80211 get the API wrong (except for
cfg80211) and are unable to cope with multiple registrations for
the same frame type, which is valid due to the match filter.
This seems to indicate the API is wrong, and we should maintain
the full information in cfg80211 instead of the drivers.
Change the API to no longer inform the driver about individual
registrations and unregistrations, but rather every time about
the entire state of the entire wiphy and single wdev, whenever
it may have changed. This also simplifies the code in cfg80211
as it no longer has to track exactly what was unregistered and
can free things immediately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20200417124300.f47f3828afc8.I7f81ef59c2c5a340d7075fb3c6d0e08e8aeffe07@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Extend cfg80211_rx_unprot_mlme_mgmt() to cover indication of unprotected
Beacon frames in addition to the previously used Deauthentication and
Disassociation frames. The Beacon frame case is quite similar, but has
couple of exceptions: this is used both with fully unprotected and also
incorrectly protected frames and there is a rate limit on the events to
avoid unnecessary flooding netlink events in case something goes wrong.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20200401142548.6990-1-jouni@codeaurora.org
[add missing kernel-doc]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers that trigger roaming need to know the lifetime of the configured
PMKSA for deciding whether to trigger the full or PMKSA cache based
authentication. The configured PMKSA is invalid after the PMK lifetime
has expired and must not be used after that and the STA needs to
disassociate if the PMK expires. Hence the STA is expected to refresh
the PMK with a full authentication before this happens (e.g., when
reassociating to a new BSS the next time or by performing EAPOL
reauthentication depending on the AKM) to avoid unnecessary
disconnection.
The PMK reauthentication threshold is the percentage of the PMK lifetime
value and indicates to the driver to trigger a full authentication roam
(without PMKSA caching) after the reauthentication threshold time, but
before the PMK timer has expired. Authentication methods like SAE need
to be able to generate a new PMKSA entry without having to force a
disconnection after this threshold timeout. If no roaming occurs between
the reauthentication threshold time and PMK lifetime expiration,
disassociation is still forced.
The new attributes for providing these values correspond to the dot11
MIB variables dot11RSNAConfigPMKLifetime and
dot11RSNAConfigPMKReauthThreshold.
This type of functionality is already available in cases where user
space component is in control of roaming. This commit extends that same
capability into cases where parts or all of this functionality is
offloaded to the driver.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20200312235903.18462-1-jouni@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pass the AP's HE operation element to the driver.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200131111300.891737-18-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for requesting that the ranging measurement will use
the trigger-based / non trigger-based flow instead of the EDCA based
flow.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200131111300.891737-2-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds support for disabling pre-auth rx over the nl80211 control
port for mac80211.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20200312091055.54257-3-markus.theil@tu-ilmenau.de
[fix indentation slightly, squash feature enablement]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds support to configure per TID RTSCTS control
configuration to enable/disable through the
NL80211_TID_CONFIG_ATTR_RTSCTS_CTRL attribute.
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Link: https://lore.kernel.org/r/1579506687-18296-5-git-send-email-tamizhr@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds support to configure per TID AMPDU control
configuration to enable/disable aggregation through the
NL80211_TID_CONFIG_ATTR_AMPDU_CTRL attribute.
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Link: https://lore.kernel.org/r/1579506687-18296-4-git-send-email-tamizhr@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds support to configure per TID retry configuration
through the NL80211_TID_CONFIG_ATTR_RETRY_SHORT and
NL80211_TID_CONFIG_ATTR_RETRY_LONG attributes. This TID specific
retry configuration will have more precedence than phy level
configuration.
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Link: https://lore.kernel.org/r/1579506687-18296-3-git-send-email-tamizhr@codeaurora.org
[rebase completely on top of my previous API changes]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make some changes to the TID-config API:
* use u16 in nl80211 (only, and restrict to using 8 bits for now),
to avoid issues in the future if we ever want to use higher TIDs.
* reject empty TIDs mask (via netlink policy)
* change feature advertising to not use extended feature flags but
have own mechanism for this, which simplifies the code
* fix all variable names from 'tid' to 'tids' since it's a mask
* change to cfg80211_ name prefixes, not ieee80211_
* fix some minor docs/spelling things.
Change-Id: Ia234d464b3f914cdeab82f540e018855be580dce
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the new NL80211_CMD_SET_TID_CONFIG command to support
data TID specific configuration. Per TID configuration is
passed in the nested NL80211_ATTR_TID_CONFIG attribute.
This patch adds support to configure per TID noack policy
through the NL80211_TID_CONFIG_ATTR_NOACK attribute.
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Link: https://lore.kernel.org/r/1579506687-18296-2-git-send-email-tamizhr@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
IEEE P802.11-REVmd/D3.0 adds support for protecting Beacon frames using
a new set of keys (BIGTK; key index 6..7) similarly to the way
group-addressed Robust Management frames are protected (IGTK; key index
4..5). Extend cfg80211 and nl80211 to allow the new BIGTK to be
configured. Add an extended feature flag to indicate driver support for
the new key index values to avoid array overflows in driver
implementations and also to indicate to user space when this
functionality is available.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20200222132548.20835-2-jouni@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The field "reg_notifier" was already documented above the definition of
struct wiphy. The comment inside the definition of the struct did not
bring more information.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20200221115604.594035-6-Jerome.Pouiller@silabs.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The field "perm_addr" was already documented above the definition of
struct wiphy. Comments were almost identical.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20200221115604.594035-5-Jerome.Pouiller@silabs.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The field "_net" was already documented above the definition of struct
wiphy. Both comments were identical.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20200221115604.594035-4-Jerome.Pouiller@silabs.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Field "registered" was documented three times: twice in the
documentation block of struct wiphy and once inside the struct
definition. This patch keep only one comment.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20200221115604.594035-3-Jerome.Pouiller@silabs.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The field "privid" was already documented above the definition of struct
wiphy. Comments were not identical, but they said more or less the same
thing.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20200221115604.594035-2-Jerome.Pouiller@silabs.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The field "probe_resp_offload" was already documented above the
definition of struct wiphy. Both comments were identical.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20200221115604.594035-1-Jerome.Pouiller@silabs.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit 8c3ed7aa2b.
As Jouni points out, there's really no need for this, since the
RSN pre-authentication frames are normal data frames, not port
control frames (locally).
We can still revert this now since it hasn't actually gone beyond
-next.
Fixes: 8c3ed7aa2b ("nl80211: add src and dst addr attributes for control port tx/rx")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20200224101910.b746e263287a.I9eb15d6895515179d50964dec3550c9dc784bb93@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* 802.11 frame encapsulation offload support
* more HE (802.11ax) support, including some for 6 GHz band
* powersave in hwsim, for better testing
Of course as usual there are various cleanups and small fixes.
-----BEGIN PGP SIGNATURE-----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=CgmJ
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2020-02-14' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
A few big new things:
* 802.11 frame encapsulation offload support
* more HE (802.11ax) support, including some for 6 GHz band
* powersave in hwsim, for better testing
Of course as usual there are various cleanups and small fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently a mac80211 driver can only set the txq_limit when using
wake_tx_queue. Not all drivers use wake_tx_queue. This patch adds a new
element to wiphy allowing a driver to set a custom tx_queue_len and the
code that will apply it in case it is set. The current default is
1000 which is too low for ath11k when doing HE rates.
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20200211122605.13002-1-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When using control port over nl80211 in AP mode with
pre-authentication, APs need to forward frames to other
APs defined by their MAC address. Before this patch,
pre-auth frames reaching user space over nl80211 control
port have no longer any information about the dest attached,
which can be used for forwarding to a controller or injecting
the frame back to a ethernet interface over a AF_PACKET
socket.
Analog problems exist, when forwarding pre-auth frames from
AP -> STA.
This patch therefore adds the NL80211_ATTR_DST_MAC and
NL80211_ATTR_SRC_MAC attributes to provide more context
information when forwarding.
The respective arguments are optional on tx and included on rx.
Therefore unaware existing software is not affected.
Software which wants to detect this feature, can do so
by checking against:
NL80211_EXT_FEATURE_CONTROL_PORT_OVER_NL80211_MAC_ADDRS
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20200115125522.3755-1-markus.theil@tu-ilmenau.de
[split into separate cfg80211/mac80211 patches]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit ab4dfa2053 ("cfg80211: Allow drivers to advertise supported AKM
suites") introduces the support to advertize supported AKMs to userspace.
This needs an enhancement to advertize the AKM support per interface type,
specifically for the cfg80211-based drivers that implement SME and use
different mechanisms to support the AKM's for each interface type (e.g.,
the support for SAE, OWE AKM's take different paths for such drivers on
STA/AP mode).
This commit aims the same and enhances the earlier mechanism of advertizing
the AKMs per wiphy. Add new nl80211 attributes and data structure to
provide supported AKMs per interface type to userspace.
the AKMs advertized in akm_suites are default capabilities if not
advertized for a specific interface type in iftype_akm_suites.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Link: https://lore.kernel.org/r/20200126203032.21934-1-vjakkam@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
John Crispin