Add ACL core infrastructure for Spectrum ASIC. This infra provides an
abstraction layer over specific HW implementations. There are two basic
objects used. One is "rule" and the second is "ruleset" which serves as a
container of multiple rules. In general, within one ruleset the rules are
allowed to have multiple priorities and masks. Each ruleset is bound to
either ingress or egress a of port netdevice.
The initial TCAM implementation is very simple and limited. It utilizes
parman lsort manager to take care of TCAM region layout.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using the MPSC register, add the functions that configure port-based
packet sampling in hardware and the necessary datatypes in the
mlxsw_sp_port struct. In addition, add the necessary trap for sampled
packets and integrate with matchall offloading to allow offloading of the
sample tc action.
The current offload support is for the tc command:
tc filter add dev <DEV> parent ffff: \
matchall skip_sw \
action sample rate <RATE> group <GROUP> [trunc <SIZE>]
Where only ingress qdiscs are supported, and only a combination of
matchall classifier and sample action will lead to activating hardware
packet sampling.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the device, a MID entry represents a group of local ports, which can
later be bound to a MDB entry.
The lookup of an existing MID entry is currently done using the provided
MC MAC address and VID, from the Linux bridge. However, this can result
in an incorrect reuse of the same MID index in different VLAN-unaware
bridges (same IP MC group and VID 0).
Fix this by performing the lookup based on FID instead of VID, which is
unique across different bridges.
Fixes: 3a49b4fde2 ("mlxsw: Adding layer 2 multicast support")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, devlink register/unregister is done directly from
spectrum/switchx2 port create/remove functions. With a need to
introduce a port type change, the devlink port instances have to be
persistent across type changes, therefore across port create/remove
function calls. So do a bit of reshuffling to achieve that.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Elad Raz <eladr@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the number of resources is going to get much bigger, ease up the
addition by simly defining IDs. Convert the existing structure members
to a set array, one for validity, one for values. Introduce a set of
getters and setters for easy access.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, in order to offload a FIB entry to HW we use switchdev op.
However that has limits. Mainly in case we need to make the HW aware of
all route prefixes configured in kernel. HW needs to know those in order
to properly trap appropriate packets and pass the to kernel to do
the forwarding. Abort mechanism is now handled within the mlxsw driver.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace max rif const with using the result from resource query.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace max virtual routers const with the result from
the resource query.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use resources from resource query to determine values for
the profile configuration.
Add KVD determined section sizes to the resources struct.
Change the profile struct and value to match this changes.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use max lag and max ports in lag resources as the result of resource query
instead of using const to save them.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the default statistics ndo to return HW statistics
(like the one returned by ethtool_ops).
The HW stats are collected to a cache by delayed work every 1 sec.
Implement the offload stat ndo.
Add a function to get SW statistics, to be called from this function.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now the device always reported autonegotiation to be off
although it was on by default.
Allow the user to disable / enable autonegotiation and report its status
correctly.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mediatek/mtk_eth_soc.c
drivers/net/ethernet/qlogic/qed/qed_dcbx.c
drivers/net/phy/Kconfig
All conflicts were cases of overlapping commits.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the notifier is registered for every asic instance, however the
same block. Fix this by moving the registration to module init.
Fixes: c723c735fa ("mlxsw: spectrum_router: Periodically update the kernel's neigh table")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are going to prevent the device from generating learning
notifications for a port that was configured with learning disabled.
Since learning configuration is done per {Port, VID} we need to apply
the port's learning configuration for any VID that is added to the
bridge port's VLAN filter list.
When a VID is added to the VLAN filter list of a VLAN-aware bridge port,
configure the {Port, VID} learning status according to the port's
configuration. When the VID is removed, disable learning for the {Port,
VID}.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After registering a netdevice it's possible for user space applications
to configure an IP address on it. From the driver's perspective, this
means a router interface (RIF) should be created for the PVID vPort.
Therefore, we must create the PVID vPort before registering the
netdevice.
Fixes: 99724c18fc ("mlxsw: spectrum: Introduce support for router interfaces")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch offloads port mirroring directives to hw using the matchall TC
with action mirror. It includes both the implementation of the
ndo_setup_tc function for the spectrum driver and the spectrum hardware
offload configuration code.
The hardware offload code is basically two new functions which are capable
of adding and removing a new mirror ports pair. It is done using the MPAT,
MPAR and SBIB registers:
- A new Switch-Port Analyzer (SPAN) entry is added using MPAT to the 'to'
port.
- The 'to' port is bound to the SPAN entry using MPAR register.
- In case of egress SPAN, the 'to' port gets a new internal shared
buffer using SBIB register.
In addition, a new database was added to the mlxsw_sp struct to store all
the SPAN entries and their bound ports list. The number of supported SPAN
entries is determined by resource query.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now, the driver sends arp probes for all unresolved neighbours that are
currently a nexthop for some route on the system. The job is set
periodically every 5 seconds.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For nexthop neighbours we need to make kernel to think there is a traffic
flowing to them preventing it from going to stale state. Otherwise
kernel would stale it and eventually the neigh would be removed from HW
and nexthop as well. That would reduce ECMP group in HW.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement next-hop routing offload including ECMP. To make it possible,
introduce next-hop group entity. This entity keeps track of resolved
neighbours and updates HW adjacency table accordingly. Note that HW
next-hops are stored in this adjacency table, in form of MAC.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a very simple manager for KVD linear area. Currently, the
allocator will either allocate a single entry from pre-defined sub-area,
or in case more than one entry is needed, it will allocate 32-entry chunk
in other pre-defined sub-area.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Override the defaults and define the area sizes ourselves.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As previously explained, the driver should periodically poll the device
for neighbours activity according to the configured DELAY_PROBE_TIME.
This will prevent active neighbours from staying in STALE state for long
periods of time.
During init configure the polling interval according to the
DELAY_PROBE_TIME used in the default table. In addition, register a
netevent notification block, so that the interval is updated whenever
DELAY_PROBE_TIME changes.
Using the computed interval schedule a delayed work, which will update
the kernel via neigh_event_send() on any active neighbour since the last
delayed work.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to hold some private data for every neigh entry. It would be
possible to do it using neigh_priv_len/ndo_neigh_construct/
ndo_neigh_destroy however only for the port device itself. That would not
work for stacked devices like bridge/team/bond. So introduce a private
neigh table. Hook onto ndos neigh_construct/destroy and add/remove
table entry according to that.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As with the previously introduced L3 interfaces, listen to 'inetaddr'
notifications sent for bridges devices configured on top of the port
netdevs and create / destroy router interfaces (RIFs) accordingly.
This also includes VLAN devices configured on top of the VLAN-aware
bridge.
The RIFs will be destroyed either when the last IP address is removed or
when the underlying FID is is destroyed.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before introducing support for L3 interfaces on top of the VLAN-aware
bridge we need to add some missing infrastructure.
Such an interface can either be the bridge device itself or a VLAN
device on top of it. In the first case the router interface (RIF) is
associated with FID 1, which is created whenever the first port netdev
joins the bridge. We currently assume the default PVID is 1 and that
it's already created, as it seems reasonable. This can be extended in
the future.
However, in the second case it's entirely possible we've yet to create a
matching FID. This can happen if the VLAN device was configured before
making any bridge port member in the VLAN.
Prevent such ordering problems by using the VLAN device's CHANGEUPPER
event to configure the FID. Make the VLAN device hold a reference to the
FID and prevent it from being destroyed even if none of the port netdevs
is using it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous commit deprecated the vFIDs used to get traffic to the CPU
('port_vfids'). Thus, we now use the vFIDs as god intended and the
artificial split is no longer needed.
Rename functions and variables to reflect that.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now we only supported bridged interfaces. Packets ingressing
through the switch ports were either classified to FIDs (in the case of
the VLAN-aware bridge) or vFIDs (in the case of VLAN-unaware bridges).
The packets were then forwarded according to the FDB. Routing was done
entirely in slowpath, by splitting the vFID range in two and using the
lower 0.5K vFIDs as dummy bridges that simply flooded all incoming
traffic to the CPU.
Instead, allow packets to be routed in the device by creating router
interfaces (RIFs) that will direct them to the router block.
Specifically, the RIFs introduced here are Sub-port RIFs used for VLAN
devices and port netdevs. Packets ingressing from the {Port / LAG ID, VID}
with which the RIF was programmed with will be assigned to a special
kind of FIDs called rFIDs and from there directed to the router.
Create a RIF whenever the first IPv4 address was programmed on a VLAN /
LAG / port netdev. Destroy it upon removal of the last IPv4 address.
Receive these notifications by registering for the 'inetaddr'
notification chain. A non-zero (10) priority is used for the
notification block, so that RIFs will be created before routes are
offloaded via FIB code.
Note that another trigger for RIF destruction are CHANGEUPPER
notifications causing the underlying FID's reference count to go down to
zero. This can happen, for example, when a VLAN netdev with an IP address
is put under bridge. While this configuration doesn't make sense it does
cause the device and the kernel to get out of sync when the netdev is
unbridged. We intend to address this in the future, hopefully in current
cycle.
Finally, Remove the lower 0.5K vFIDs, as they are deprecated by the RIFs,
which will trap packets according to their DIP.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are just about to introduce router interfaces (RIFs), but before that
we need to be able update the device with the correct RIF attributes
whenever they change for the netdev the RIF is backing. Two such
attributes are MTU and MAC.
The MAC is used both to set the source MAC of packets egressing from the
RIF and also to program an FDB rule that will direct packets to the
router block.
Use the existing netdevice notification block and respond to CHANGEADDR
and CHANGEMTU accordingly. Store both attributes in the RIF struct
in case we need to revert to old attributes following a failed update.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add functions that iterate over lower devices and find port device.
As a dependency add netdev_for_each_all_lower_dev and
netdev_for_each_all_lower_dev_rcu macro with
netdev_all_lower_get_next and netdev_all_lower_get_next_rcu shelpers.
Also, add functions to return mlxsw struct according to lower device
found and mlxsw_port struct with a reference to lower device.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement ipv4 FIB entries addition and removal. Initially, we support
local and broadcast routes using "ip2me" trap action.
Also, unicast routes without nexthop are supported using "local" action.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Virtual router is a construct used inside HW. In this implementation
we map kernel tables to virtual routers one to one. Introduce management
logic to create virtual routers when needed and destroy in case they are
no longer in use. According to that, call into LPM tree management.
Each virtual router is always bound to one LPM tree.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce basic LPM tree management allowing to share the trees in
between tables if the used prefixes in the tables are the same.
Build the tree structure according to the used prefixes. Although it is
not optimal for many use cases, this initial implementation does only
simple linear left-tree. More advanced structures will be introduced
later on, possibly including mechanisms to change trees on the fly.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shadow FIB is needed in order to hold additional information for FIB
entries and keep track of used prefixes. That is needed for the LPM tree
construction to be introduced later on in this set.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When enabling the router in the device we will represent L3 netdevs
using router interfaces (RIFs). These will be specified whenever
programming routes or neighbours on the netdev.
Introduce the basic RIF infrastructure which allows one to lookup a RIF
by its netdev. Later patches in the series will extend this, but the
basic routines are needed now in order to direct traffic to CPU.
Pointers to the RIF structs are stored in an array indexed by the RIF's
number. This will allow us to efficiently update the kernel's neighbour
table when regularly dumping the device's table.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a skeleton router file and do basic HW initialization of router.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When port isn't bridged it is still possible to invoke switchdev ops and
configure the device's VLAN filters.
However, this will require us to use different Router InterFaces (RIFs)
for the same netdev, instead of one per-netdev as with any other
configuration.
Taking the above into account and the fact that this functionality is
questionable with regards to the device's normal use-case, remove it and
instead return an error.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are situations in which a vPort is destroyed while still holding
references to device's resources such as FIDs and FDB records. This can
happen, for example, when a VLAN device is deleted while still being
bridged.
Instead of trying to make sure vPort destruction is invoked when it no
longer uses device's resources, just free them upon destruction. This
simplifies the code, as we no longer need to take different situations
into account when events are received - cleanup is taken care of in one
place.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FDB entries are learned using {Port / LAG ID, FID} and therefore should
be flushed whenever a port (vPort) leaves its FID (vFID).
However, when the bridge port is a LAG device (or a VLAN device on top),
then FDB flushing is conditional. Ports removed from such LAG
configurations must not trigger flushing, as other ports might still be
members in the LAG and therefore the bridge port is still active.
The decision whether to flush or not was previously computed in the
netdevice notification block, but in order to flush the entries when a
port leaves its FID this decision should be computed there.
Strip the notification block from this logic and instead move it to one
FDB flushing function that is invoked from both the FID / vFID leave
functions.
When port isn't member in LAG, FDB flushing should always occur.
Otherwise, it should occur only when the last port (vPort) member in the
LAG leaves the FID (vFID).
This will allow us - in the next patch - to simplify the cleanup code
paths that are hit whenever the topology above the port netdevs changes.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all vPorts will have FIDs assigned to them, so make sure functions
first test for FID presence.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As previously explained, not all vPorts will be assigned FIDs, so instead
of returning the FID index of a vPort, return a pointer to its FID
struct. This will allow us to know whether it's legal to access the
vPort's FID parameters such as index and device.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When L3 interfaces will be introduced a vPort won't necessarily have a
FID assigned to it. This can happen if it's not member in a bridge (in
which case it's assigned a vFID) or doesn't have an IP address (in which
case it's assigned an rFID).
Therefore, instead check the VID parameter to test whether a port is a
vPort or not.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a very similar way to the vFIDs, make the first 4K FIDs - used in the
VLAN-aware bridge - use the new FID struct.
Upon first use of the FID by any of the ports do the following:
1) Create the FID
2) Setup a matching flooding entry
3) Create a mapping for the FID
Unlike vFIDs, upon creation of a FID we always create a global
VID-to-FID mapping, so that ports without upper vPorts can use it
instead of creating an explicit {Port, VID} to FID mapping.
When a port leaves a FID the reverse is performed. Whenever the FID's
reference count reaches zero the FID is deleted along with the global
mapping.
The per-FID struct will later allow us to configure L3 interfaces on top
of the VLAN-aware bridge.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now we had a dedicated struct only for vFIDs, but before
introducing support for L3 interfaces we need to make it generic and
use it for all three types of FIDs:
1) FIDs - 0..4K-1, used for the VLAN-aware bridge
2) vFIDs - 4K..15K-1, used for VLAN-unaware bridges
3) rFIDs - 15K..16K-1, used to direct traffic to / from the router in
the device. Will be introduced later in the series.
The three types of L3 interfaces - Router InterFaces, RIFs - that will
be introduced correspond to the three types of FIDs and are configured
using them. Therefore, we'll need to store the links between them as
well as a reference count on the underlying FID, so that the
corresponding RIF will be destroyed when it reaches zero.
Note that the lower 0.5K vFIDs are currently used for for non-bridged
netdevs, so that traffic could be flooded to the CPU port. However, when
rFIDs will be introduced we'll no longer need these and they too will be
used for VLAN-unaware bridges.
Make the vFID struct generic by renaming it and some of its fields. FIDs
will be converted to use it later in the series.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a FID index instead of vFID and ease the transition towards a
generic FID struct.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In all call sites 'only_uc' is set to false, so strip it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a macro to do this kind of declarations, so use it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When rtnl_fill_ifinfo() is called for a certain netdevice it queries its
various parameters such as switch id and physical port name. The
function might get called in an atomic context, which means the
underlying driver must not sleep during the query operation.
Don't query the device and sleep during ndo_get_phys_port_name(), but
instead store the needed parameters in port creation time.
Fixes: 2bf9a58675 ("mlxsw: spectrum: Add support for physical port names")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement occupancy API introduced in devlink and mlxsw core. This is
done by accessing SBPM register for Port-Pool and SBSR for Port-TC
current and max occupancy values. Max clear is implemented using the
same registers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement previously introduced mlxsw core shared buffer API.
For Spectrum, that is done utilizing registers SBPR, SBCM and SBPM.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to achieve faster dumping of current setting and also in order
to provide possibility to get pool mode without a need to query hardware,
do cache the configuration in driver.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove devlink port reg/unreg from spectrum and switchx2 code and rather
do the common work in core. That also ensures code separation where
devlink is only used in core.c.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the appropriate DCB ops and allow a user to configure certain
traffic classes as lossless.
The operation configures PFC for both the egress (respecting PFC frames)
and ingress (sending PFC frames) parts of the port.
At egress, when a PFC frame is received for a PFC enabled priority, then
all the priorities mapped to the same TC are stopped.
At ingress, the priority group (PG) buffers to which the enabled PFC
priorities are mapped are configured to be lossless. PFC frames will be
transmitted when the Xoff threshold is crossed.
The user-supplied delay parameter is used to determine the PG's size
according to the following formula:
PG_SIZE = PG_SIZE_LOSSY + delay * CELL_FACTOR + MTU
In the worst case scenario the delay will be made up of packets that
are all of size CELL_SIZE + 1, which means each packet will require
almost twice its true size when buffered in the switch. We therefore
multiply this value by the "cell factor", which is close to 2.
Another MTU is added in case the transmitting host already started
transmitting a maximum length frame when the PFC packet was received.
As with PAUSE enabled ports, when the port's MTU is changed both the
PGs' size and threshold are adjusted accordingly.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a packet ingress the switch it's placed in its assigned priority
group (PG) buffer in the port's headroom buffer while it goes through
the switch's pipeline. After going through the pipeline - which
determines its egress port(s) and traffic class - it's moved to the
switch's shared buffer awaiting transmission.
However, some packets are not eligible to enter the shared buffer due to
exceeded quotas or insufficient space. Marking their associated PGs as
lossless will cause the packets to accumulate in the PG buffer. Another
reason for packets accumulation are complicated pipelines (e.g.
involving a lot of ACLs).
To prevent packets from being dropped a user can enable PAUSE frames on
the port. This will mark all the active PGs as lossless and set their
size according to the maximum delay, as it's not configured by user.
+----------------+ +
| | |
| | |
| | |
| | |
| | |
| | | Delay
| | |
| | |
| | |
| | |
| | |
Xon/Xoff threshold +----------------+ +
| | |
| | | 2 * MTU
| | |
+----------------+ +
The delay (612 [Cells]) was calculated according to worst-case scenario
involving maximum MTU and 100m cables.
After marking the PGs as lossless the device is configured to respect
incoming PAUSE frames (Rx PAUSE) and generate PAUSE frames (Tx PAUSE)
according to user's settings.
Whenever the port's headroom configuration changes we take into account
the PAUSE configuration, so that we correctly set the PG's type (lossy /
lossless), size and threshold. This can happen when:
a) The port's MTU changes, as it directly affects the PG's size.
b) A PG is created following user configuration, by binding a priority
to it.
Note that the relevant SUPPORTED flags were already mistakenly set by
the driver before this commit.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow a user to set maximum rate for a particular TC using DCB ops.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the appropriate DCB ops and allow a user to configure:
* Priority to traffic class (TC) mapping with a total of 8
supported TCs
* Transmission selection algorithm (TSA) for each TC and the
corresponding weights in case of weighted round robin (WRR)
As previously explained, we treat the priority group (PG) buffer in the
port's headroom as the ingress counterpart of the egress TC. Therefore,
when a certain priority to TC mapping is configured, we also configure
the port's headroom buffer.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce basic infrastructure for DCB and add the missing ops in
following patches.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Buffers in the switch store packets in units called buffer cells. Add a
helper to convert from bytes to cells, so that the actual number of
cells required (result is round up) is returned.
Also, drop the SB (shared buffer) acronym from the BYTES_PER_CELL macro,
as this unit is also used in the ports' buffers and not only the
switch's shared buffer.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resources allocated for these bridges at init time cannot be later used
for other purposes. While current number is supported by the device,
it's mostly theoretical with regards to any real use case, which leads
to poor utilization of device's resources. Solve that by reducing the
number.
The long term plan is to make this value (along with others) user
configurable via devlink and write it to NVRAM, so that it can be used
during the next init. Until then we must hardcode such values.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c62987bbd8 ("bridge: push bridge setting ageing_time down to
switchdev") added a check for minimum and maximum ageing time, but this
breaks existing behaviour where one can set ageing time to 0 for a
non-learning bridge.
Push this check down to the driver and allow the check in the bridge
layer to be removed. Currently ageing time 0 is refused by the driver,
but we can later add support for this functionality.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow a user to split or unsplit a port using the newly introduced
devlink ops.
Once split, the original netdev is destroyed and 2 or 4 others are
created, according to user configuration. The new ports are like any
other port, with the sole difference of supporting a lower maximum
speed. When unsplit, the reverse process takes place.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port netdevs are each associated with a different local port number
in the device. These local ports are grouped into groups of 4 (e.g.
(1-4), (5-8)) called clusters. The cluster constitutes the one of two
possible modules they can be mapped to. This mapping is board-specific
and done by the device's firmware during init.
When splitting a port by 4, the device requires us to first unmap all
the ports in the cluster and then map each to a single lane in the module
associated with the port netdev used as the handle for the operation.
This means that two port netdevs will disappear, as only 100Gb/s (4
lanes) ports can be split and we are guaranteed to have two of these
((1, 3), (5, 7) etc.) in a cluster.
When unsplit occurs we need to reinstantiate the two original 100Gb/s
ports and map each to its origianl module. Therefore, during driver init
store the initial local port to module mapping, so it can be used later
during unsplitting.
Note that a by 2 split doesn't require us to store the mapping, as we
only need to reinstantiate one port whose module is known.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement newly introduced devlink interface. Add devlink port instances
for every port and set the port types accordingly.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When PVID is toggled off on a port member in a VLAN filtering bridge or
the PVID VLAN is deleted, make the port drop untagged packets. Reverse
the operation when PVID is toggled back on.
Set the PVID back to the default (1), when leaving the bridge so that
untagged traffic will be directed to the CPU.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When switchdev drivers process FDB notifications from the underlying
device they resolve the netdev to which the entry points to and notify
the bridge using the switchdev notifier.
However, since the RTNL mutex is not held there is nothing preventing
the netdev from disappearing in the middle, which will cause
br_switchdev_event() to dereference a non-existing netdev.
Make switchdev drivers hold the lock at the beginning of the
notification processing session and release it once it ends, after
notifying the bridge.
Also, remove switchdev_mutex and fdb_lock, as they are no longer needed
when RTNL mutex is held.
Fixes: 03bf0c2812 ("switchdev: introduce switchdev notifier")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible for a user to remove a port from a LAG device, while the
LAG device or VLAN devices on top of it are bridged. In these cases,
bridge's teardown sequence is never issued, so we need to take care of
it ourselves.
When LAG's unlinking event is received by port netdev:
1) Traverse its vPorts list and make those member in a bridge leave it.
They will be deleted later by LAG code.
2) Make the port netdev itself leave its bridge if member in one.
Fixes: 0d65fc1304 ("mlxsw: spectrum: Implement LAG port join/leave")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/bonding/bond_main.c
drivers/net/ethernet/mellanox/mlxsw/spectrum.h
drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c
The bond_main.c and mellanox switch conflicts were cases of
overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Dumping the FDB (invoked with a process context) or handling FDB
notifications (polled periodicly in delayed work) might each entail
multiple EMAD transcations due to the number of entries.
While we only allow one EMAD transaction at a time, there is nothing
stopping the dump and notification processing sessions from
interleaving. However, this is forbidden by the hardware, so we need to
make sure only one of these sessions can run at a time.
Solve this by adding a mutex ('fdb_lock'), as both kernel threads can
sleep while waiting for the response EMAD.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add SWITCHDEV_OBJ_ID_PORT_MDB switchdev ops support. On first MDB insertion
creates a new multicast group (MID) and add members port to the MID. Also
add new MDB entry for the flooding-domain (fid-vid) and link the MDB entry
to the newly constructed MC group.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a vlan is been configured, remeber the untagged mode of the vlan.
When displaying the list of configured VLANs, show the untagged attribute.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All the member VLAN devices in a bridge need to share the same vFID.
To achieve that, expand the vFID struct to include the associated bridge
device (or lack of) and allow one to lookup a vFID based on a bridge
device.
When joining a bridge, lookup the relevant vFID or create one if none
exists. Next, make the VLAN device use the vFID.
Leaving a bridge can either occur because a user removed the VLAN device
from a bridge or because the VLAN device was deleted by the user. In the
latter case the bridge's teardown sequence is invoked after the hardware
vPort is already gone. Therefore, when unlinking the VLAN device from
the real device, check if the associated vPort is bridged and act
accordingly. The bridge's notification will be ignored in this case.
Note that bridging a VLAN interface with an ordinary port netdev is
currently not supported, but not forbidden. This will be addressed in a
follow-up patchset.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FDB notifications contain the FID and port (or LAG ID) on which the MAC
was learned. In the case of the 802.1Q bridge one can easily derive the
matching VID - as FID equals VID - and generate the appropriate
notification for the software bridge. With VLAN devices this is no
longer the case, as these are associated with a vFID.
Solve that by converting the FID to a vFID and lookup the matching VLAN
device. From that derive the VID and whether learning (and learning
sync) should occur.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We previously used only one flood table for packets classified to vFIDs.
However, since we are going to add support for bridges between VLAN
interfaces (mapped to vFIDs) we need to add one more flood table.
That way we can separate the flooding domain of unknown unicast traffic
from all the rest and support flood control (as we do with the 802.1Q
bridge).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now we used a 1:1 mapping - based on VID - to map a VLAN
interface to a vFID. However, a different scheme is needed in order to
support bridges between VLAN interfaces, as all the member interfaces -
which can have different VIDs - need to share the same vFID.
Solve that by splitting the vFID range in two:
1. Non-bridged VLAN interfaces
2. Bridged VLAN interfaces
When a VLAN interface is created, assign it the next available vFID in
the first range, unless one already exists for that VID or number of
vFIDs in the range was exceeded. When interface is removed, free the
vFID, unless other interfaces are mapped to it.
To accomplish the above:
1. Store the VID to vFID mapping in a new struct (mlxsw_sp_vfid), which
has a global context and holds a reference count.
2. Create a vPort (dummy in case of bridge SELF invocation) on top of
of the physical port and hold a reference to the associated vFID.
vfid vfid
+-------------+ +-------------+
| vfid | | vfid |
| vid +---> ... | vid |
| nr_vports | | nr_vports |
+------+------+ +------+------+
|
+-----------------------+-------+
| |
vport vport
+-------------+ +-------------+
| ... | | ... |
| *vfid +---> ... | *vfid +---> ...
| ... | | ... |
+------+------+ +------+------+
| |
port port
+-------------+ +-------------+
| ... | | ... |
| vports_list | | vports_list |
| ... | | ... |
+-------------+ +-------------+
swXpY swXpZ
Next patches in the series will add the missing infrastructure for the
second range and transfer vPorts between the two ranges according to the
received notifications.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding support for bridges between VLAN interfaces, we'll introduce
a new entity called a vPort, which is a represntation of the VLAN
interface in the hardware.
The main difference between a vPort and a physical port is that several
FIDs can be bound to the latter, whereas only one (called a vFID) can be
bound to the first.
Therefore, it makes sense to use the same struct to represent the two,
but to only allocate the 'active_vlans' bitmap in case of a physical
port.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement basic procedures for joining/leaving port to/from LAG. That
includes HW setup of collector, core LAG mapping setup.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add or remove a bridged port from the flooding domain of unknown unicast
packets according to user configuration.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is a flag anyway, so move it to existing u8 flag and don't waste mem.
Fix the flags to be in single u8 on the way.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for new generation Mellanox Spectrum ASIC, 10/25/40/50 and
100Gb/s Ethernet Switch.
The initial driver implements bridge forwarding offload including
bridge internal VLAN support, FDB static entries, FDB learning and
HW ageing including their setup.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko