This patch correct poll_bnx2x (ndo_poll_controller call) which was not
functioning well with MSI-X.
Signed-off-by: Merav Sicron <meravs@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move netif_napi_add for all queues from the probe call to the open call, to
avoid the case that napi objects are added for queues that may eventually not
be initialized and activated. With the former behavior, the driver could crash
when netpoll was calling ndo_poll_controller.
Signed-off-by: Merav Sicron <meravs@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With a low enough MSS on the link partner and TSO enabled locally, the
networking stack can periodically send a very large (e.g. 64KB) TCP
message for which the driver will attempt to use more Tx descriptors than
are available by default in the Tx ring. This is due to a workaround in
the code that imposes a limit of only 4 MSS-sized segments per descriptor
which appears to be a carry-over from the older e1000 driver and may be
applicable only to some older PCI or PCIx parts which are not supported in
e1000e. When the driver gets a message that is too large to fit across the
configured number of Tx descriptors, it stops the upper stack from queueing
any more and gets stuck in this state. After a timeout, the upper stack
assumes the adapter is hung and calls the driver to reset it.
Remove the unnecessary limitation of using up to only 4 MSS-sized segments
per Tx descriptor, and put in a hard failure test to catch when attempting
to check for message sizes larger than would fit in the whole Tx ring.
Refactor the remaining logic that limits the size of data per Tx descriptor
from a seemingly arbitrary 8KB to a limit based on the dynamic size of the
Tx packet buffer as described in the hardware specification.
Also, fix the logic in the check for space in the Tx ring for the next
largest possible packet after the current one has been successfully queued
for transmit, and use the appropriate defines for default ring sizes in
e1000_probe instead of magic values.
This issue goes back to the introduction of e1000e in 2.6.24 when it was
split off from e1000.
Reported-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: Stable <stable@vger.kernel.org> [2.6.24+]
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit -
"b852b72 gianfar: fix bug caused by
87c288c6e9aa31720b72e2bc2d665e24e1653c3e"
disables by default (on mac init) the hw vlan tag insertion.
The "features" flags were not updated to reflect this, and
"ethtool -K" shows tx-vlan-offload to be "on" by default.
Cc: Sebastian Poehn <sebastian.poehn@belden.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I'm slightly concerned by the "only in exceptional circumstances"
comment on __pskb_pull_tail but the structure of an skb just created
by netfront shouldn't hit any of the especially slow cases.
This approach still does slightly more work than the old way, since if
we pull up the entire first frag we now have to shuffle everything
down where before we just received into the right place in the first
place.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: xen-devel@lists.xensource.com
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull drm fixes from Dave Airlie:
"A bunch of scattered fixes ati/intel/nouveau, couple of core ones,
nothing too shocking or different."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm: Add EDID_QUIRK_FORCE_REDUCED_BLANKING for ASUS VW222S
gma500: Consider CRTC initially active.
drm/radeon: fix dig encoder selection on DCE61
drm/radeon: fix double free in radeon_gpu_reset
drm/radeon: force dma32 to fix regression rs4xx,rs6xx,rs740
drm/radeon: rework panel mode setup
drm/radeon/atom: powergating fixes for DCE6
drm/radeon/atom: rework DIG modesetting on DCE3+
drm/radeon: don't disable plls that are in use by other crtcs
drm/radeon: add proper checking of RESOLVE_BOX command for r600-r700
drm/radeon: initialize tracked CS state
drm/radeon: fix reading CB_COLORn_MASK from the CS
drm/nvc0/copy: check PUNITS to determine which copy engines are disabled
i915: Quirk no_lvds on Gigabyte GA-D525TUD ITX motherboard
drm/i915: Use the correct size of the GTT for placing the per-process entries
drm: Check for invalid cursor flags
drm: Initialize object type when using DRM_MODE() macro
drm/i915: fix color order for BGR formats on IVB
drm/i915: fix wrong order of parameters in port checking functions
Connecting an ASUS VW222S [1] over VGA a garbled screen is shown with
vertical stripes in the top half.
In commit bc42aabc [2]
commit bc42aabc6a
Author: Adam Jackson <ajax@redhat.com>
Date: Wed May 23 16:26:54 2012 -0400
drm/edid/quirks: ViewSonic VA2026w
Adam Jackson added the quirk `EDID_QUIRK_FORCE_REDUCED_BLANKING` which
is also needed for this ASUS monitor.
All log files and output from `xrandr` is included in the referenced
Bugzilla report #17629.
Please note that this monitor only has a VGA (D-Sub) connector [1].
[1] http://www.asus.com/Display/LCD_Monitors/VW222S/
[2] http://git.kernel.org/?p=linux/kernel/git/torvalds/linux.git;a=commit;h=bc42aabc6a01b92b0f961d65671564e0e1cd7592
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=17629
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Cc: <dri-devel@lists.freedesktop.org>
Cc: Adam Jackson <ajax@redhat.com>
Cc: Ian Pilcher <arequipeno@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex writes:
Highlights:
- fix a gart regression on older IGP chips
- more MSAA fixes
- fix a double free in gpu reset code
- modesetting fixes
- trinity dig encoder fix.
* 'drm-fixes-3.6' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix dig encoder selection on DCE61
drm/radeon: fix double free in radeon_gpu_reset
drm/radeon: force dma32 to fix regression rs4xx,rs6xx,rs740
drm/radeon: rework panel mode setup
drm/radeon/atom: powergating fixes for DCE6
drm/radeon/atom: rework DIG modesetting on DCE3+
drm/radeon: don't disable plls that are in use by other crtcs
drm/radeon: add proper checking of RESOLVE_BOX command for r600-r700
drm/radeon: initialize tracked CS state
drm/radeon: fix reading CB_COLORn_MASK from the CS
[this one ideally should make 3.6 - it fixes the very annoying mode setting bug]
This causes the pipe to be forced off prior to initial mode set, which
roughly mirrors the behavior of the i915 driver. It fixes initial mode
setting on my Intel DN2800MT (Cedarview) board. Without it, mode
setting triggers an out-of-range error from the monitor for most modes,
but only on initial configuration (i.e. they can be configured
successfully from userspace after that).
Signed-off-by: Forest Bond <forest.bond@rapidrollout.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Was using the DCE41 code which was wrong. Fixes
blank displays on a number of Trinity systems.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Against -net.
In the patch "netpoll: re-enable irq in poll_napi()", I tried to
fix the following warning:
[100718.051041] ------------[ cut here ]------------
[100718.051048] WARNING: at kernel/softirq.c:159 local_bh_enable_ip+0x7d/0xb0()
(Not tainted)
[100718.051049] Hardware name: ProLiant BL460c G7
...
[100718.051068] Call Trace:
[100718.051073] [<ffffffff8106b747>] ? warn_slowpath_common+0x87/0xc0
[100718.051075] [<ffffffff8106b79a>] ? warn_slowpath_null+0x1a/0x20
[100718.051077] [<ffffffff810747ed>] ? local_bh_enable_ip+0x7d/0xb0
[100718.051080] [<ffffffff8150041b>] ? _spin_unlock_bh+0x1b/0x20
[100718.051085] [<ffffffffa00ee974>] ? be_process_mcc+0x74/0x230 [be2net]
[100718.051088] [<ffffffffa00ea68c>] ? be_poll_tx_mcc+0x16c/0x290 [be2net]
[100718.051090] [<ffffffff8144fe76>] ? netpoll_poll_dev+0xd6/0x490
[100718.051095] [<ffffffffa01d24a5>] ? bond_poll_controller+0x75/0x80 [bonding]
[100718.051097] [<ffffffff8144fde5>] ? netpoll_poll_dev+0x45/0x490
[100718.051100] [<ffffffff81161b19>] ? ksize+0x19/0x80
[100718.051102] [<ffffffff81450437>] ? netpoll_send_skb_on_dev+0x157/0x240
by reenabling IRQ before calling ->poll, but it seems more
problems are introduced after that patch:
http://ozlabs.org/~akpm/stuff/IMG_20120824_122054.jpghttp://marc.info/?l=linux-netdev&m=134563282530588&w=2
So it is safe to fix be2net driver code directly.
This patch reverts the offending commit and fixes be_poll() by
avoid disabling BH there, this is okay because be_poll()
can be called either by poll_napi() which already disables
IRQ, or by net_rx_action() which already disables BH.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Reported-by: Sylvain Munaut <s.munaut@whatever-company.com>
Cc: Sylvain Munaut <s.munaut@whatever-company.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: David Miller <davem@davemloft.net>
Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Tested-by: Sylvain Munaut <s.munaut@whatever-company.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
radeon_ring_restore is freeing the memory for the saved
ring data. We need to remember that, otherwise we try to
restore the ring data again on the next try. Additional
to that it shouldn't try the reset infinitely if we have
saved ring data.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
It seems some of those IGP dislike non dma32 page despite what
documentation says. Fix regression since we allowed non dma32
pages. It seems it only affect some revision of those IGP chips
as we don't know which one just force dma32 for all of them.
https://bugzilla.redhat.com/show_bug.cgi?id=785375
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adjust the panel mode setup to match the behavior
of the vbios. Rather than checking for specific
bridge chip ids, just check the eDP configuration register.
This saves extra aux transactions and works across
DP bridge chips without requiring additional per chip
id checking.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Power gating is per crtc pair, but the powergating registers
should be called individually. The hw handles power up/down
properly. The pair is powered up if either crtc in the pair
is powered up and the pair is not powered down until both
crtcs in the pair are powered down. This simplifies
programming and should save additional power as the previous
code never actually power gated the crtc pair.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The ordering is important and the current drm code
wasn't cutting it for modern DIG encoders. We need
to have information about crtc before setting up
the encoders so I've shifted the ordering a bit.
Probably we'll need a full rework akin to danvet's
recent intel patchs. This patch fixes numerous
issues with DP bridge chips and makes link training
much more reliable.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Some plls are shared for DP.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Checking of the second colorbuffer was skipped on r700, because
CB_TARGET_MASK was 0xf. With r600, CB_TARGET_MASK is changed to 0xff,
so we must set the number of samples of the second colorbuffer to 1 in order
to pass the CS checker.
The DRM version is bumped, because RESOLVE_BOX is always rejected without this
fix on r600.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This should help catch uninitialized registers and reject commands
because of that.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Daniel writes:
"Just a few smaller things:
- Fix up a pipe vs. plane confusion from a refactoring, fixes a regression
from 3.1 (Anhua Xu).
- Fix ivb sprite pixel formats (Vijay).
- Fixup ppgtt pde placement for machines where the Bios artifically limits
the availbale gtt space in the name of ... product differentiation
(Chris). This fixes an oops.
- Yet another no_lvds quirk entry."
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
i915: Quirk no_lvds on Gigabyte GA-D525TUD ITX motherboard
drm/i915: Use the correct size of the GTT for placing the per-process entries
drm/i915: fix color order for BGR formats on IVB
drm/i915: fix wrong order of parameters in port checking functions
Ben says its just a single fix to avoid the wrong pcopy units being used.
* 'drm-nouveau-fixes' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nvc0/copy: check PUNITS to determine which copy engines are disabled
On some Fermi chipsets (NVCE particularly) PCOPY1 doesn't exist. And if
what I've seen on Kepler is true of Fermi too, chipsets of the same type
can have different PCOPY units available.
This should fix a v3.5 regression reported by a number of people effecting
suspend/resume on NVC8/NVCE chipsets.
Cc: stable@vger.kernel.org [3.5]
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Contiguous Memory Allocator requires each of its regions to be aligned
in such a way that it is possible to change migration type for all
pageblocks holding it and then isolate page of largest possible order from
the buddy allocator (which is MAX_ORDER-1). This patch relaxes alignment
requirements by one order, because MAX_ORDER alignment is not really
needed.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
CC: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
For unimplemented ioctls the dasd driver should return -ENOTTY.
Reported-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Acked-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
- move to sparse IRQ: some drivers were forgotten
- a DTS typo
- the delay for removal of old at91_mci driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQOykiAAoJEAf03oE53VmQS0MIALb4N+yRt6+Y3hjvFT386bYb
aA24NJRRn3Lsyldc7lDpKQPsAUdlPWGp6SNdUlfSFFerI2tEtwzCKkSpvN/4vH6f
e5LtlGSRKrzzDjaKl9cLJOKwm2rGPC37VjmdqFE4Mfcl3YzFGKLpvevq8uMBTCEz
6GnODy7njBk62Zzky0NR4SOgrPdI9EO5XZijXWXCfwW6MHjxRBRZf+Hn+LcJvQ5N
gLZfgMCtebsjb2x1pYP+4NfBQQLpx+sHy4on5IPlp1fEYaIaMXKCFGQNhTRqKSSD
xSpBRV/XmzmAWvffQJiiRYR4CG6lKwvhGhuxBUn5z7dRIcSoiRQKB7oISWITZs4=
=Itki
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes' of git://github.com/at91linux/linux-at91 into fixes
Fixes for AT91 related to:
- move to sparse IRQ: some drivers were forgotten
- a DTS typo
- the delay for removal of old at91_mci driver
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
ARM: at91/feature-removal-schedule: delay at91_mci removal
ARM: at91/dts: remove partial parameter in at91sam9g25ek.dts
ARM: at91/clock: fix PLLA overclock warning
ARM: at91: fix rtc-at91sam9 irq issue due to sparse irq support
ARM: at91: fix system timer irq issue due to sparse irq support
This patch (as1603) adds a NOGET quirk for the Eaton Ellipse MAX UPS
device. (The USB IDs were already present in hid-ids.h, apparently
under a different name.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Laurent Bigonville <l.bigonville@edpnet.be>
CC: <stable@vger.kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Bug fixes for various ARM platforms. About half of these are
for OMAP and submitted before but did not make it into v3.6-rc2.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Tupl
-----END PGP SIGNATURE-----
Merge tag 'fixes-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc fixes from Arnd Bergmann:
"Bug fixes for various ARM platforms. About half of these are for OMAP
and submitted before but did not make it into v3.6-rc2."
* tag 'fixes-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (39 commits)
ARM: ux500: don't select LEDS_GPIO for snowball
ARM: imx: build i.MX6 functions only when needed
ARM: imx: select CPU_FREQ_TABLE when needed
ARM: imx: fix ksz9021rn_phy_fixup
ARM: imx: build pm-imx5 code only when PM is enabled
ARM: omap: allow building omap44xx without SMP
ARM: dts: imx51-babbage: fix esdhc cd/wp properties
ARM: imx6: spin the cpu until hardware takes it down
ARM: ux500: Ensure probing of Audio devices when Device Tree is enabled
ARM: ux500: Fix merge error, no matching driver name for 'snd_soc_u8500'
ARM i.MX6q: Add virtual 1/3.5 dividers in the LDB clock path
ARM: Kirkwood: fix Makefile.boot
ARM: Kirkwood: Fix iconnect leds
ARM: Orion: Set eth packet size csum offload limit
ARM: mv78xx0: fix win_cfg_base prototype
ARM: OMAP: dmtimers: Fix locking issue in omap_dm_timer_request*()
ARM: mmp: fix potential NULL dereference
ARM: OMAP4: Register the OPP table only for 4430 device
cpufreq: OMAP: Handle missing frequency table on SMP systems
ARM: OMAP4: sleep: Save the complete used register stack frame
...
- Revert the kexec fix which caused on non-kexec shutdowns a race.
- Reuse existing P2M leafs - instead of requiring to allocate a large
area of bootup virtual address estate.
- Fix a one-off error when adding PFNs for balloon pages.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJQNppKAAoJEFjIrFwIi8fJU/oH/jdWdRqJgC5mCnu9LwrIemEj
gPTAcKw01A/2vbOY5rfXx7rCpgeU5ZM/XSt0byz/J5q0bmjjKVM106Smq1s7EaQx
OjsdLglWoZYzKJjXH/FEKRPD39f/hd+KNJu3aGEJM8UZ0htvxlg6ACGzVPJa83Pf
yrRXSycxvEevbGbuwWdNubxD5WKMMmbzi/HGGfdtL4256d0xIgxMrYgskLek96cR
cg11llC5QLzH8mX+M5iX0lchASvMITyERXyEKK2opFN8a/766yi16agP75RKZdkP
kWXp0vyOMrpy9UnOs2V1XLc/ufqNwHLcPVfecScXhz8xZWrZYOBdJQf7HAWxvLE=
=MgvT
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.6-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull three xen bug-fixes from Konrad Rzeszutek Wilk:
- Revert the kexec fix which caused on non-kexec shutdowns a race.
- Reuse existing P2M leafs - instead of requiring to allocate a large
area of bootup virtual address estate.
- Fix a one-off error when adding PFNs for balloon pages.
* tag 'stable/for-linus-3.6-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/setup: Fix one-off error when adding for-balloon PFNs to the P2M.
xen/p2m: Reuse existing P2M leafs if they are filled with 1:1 PFNs or INVALID.
Revert "xen PVonHVM: move shared_info to MMIO before kexec"
Pull powerpc fixes from Benjamin Herrenschmidt:
"I meant to sent that earlier but got swamped with other things, so
here are some powerpc fixes for 3.6. A few regression fixes and some
bug fixes that I deemed should still make it.
There's a FSL update from Kumar with a bunch of defconfig updates
along with a few embedded fixes.
I also reverted my g5_defconfig update that I merged earlier as it was
completely busted, not too sure what happened there, I'll do a new one
later."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
Revert "powerpc: Update g5_defconfig"
powerpc/perf: Use pmc_overflow() to detect rolled back events
powerpc: Fix VMX in interrupt check in POWER7 copy loops
powerpc: POWER7 copy_to_user/copy_from_user patch applied twice
powerpc: Fix personality handling in ppc64_personality()
powerpc/dma-iommu: Fix IOMMU window check
powerpc: Remove unnecessary ifdefs
powerpc/kgdb: Restore current_thread_info properly
powerpc/kgdb: Bail out of KGDB when we've been triggered
powerpc/kgdb: Do not set kgdb_single_step on ppc
powerpc/mpic_msgr: Add missing includes
powerpc: Fix null pointer deref in perf hardware breakpoints
powerpc: Fixup whitespace in xmon
powerpc: Fix xmon dl command for new printk implementation
powerpc/fsl: fix "Failed to mount /dev: No such device" errors
powerpc/fsl: update defconfigs
booke/wdt: some ioctls do not return values properly
powerpc/p4080ds: dts - add usb controller version info and port0
powerpc/85xx: mpc85xx_defconfig - add VIA PATA support for MPC85xxCDS
powerpc/fsl-pci: Only scan PCI bus if configured as a host
Pull MIPS fixes from Ralf Baechle:
"Random fixes across the MIPS tree. The two hotspots are several bugs
in the module loader and the ath79 SOC support; also noteworthy is the
restructuring of the code to synchronize CPU timers across CPUs on
startup; the old code recently ceased to work due to unrelated
changes.
All except one of these patches have sat for a significant time in
linux-next for testing."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: pci-ar724x: avoid data bus error due to a missing PCIe module
MIPS: Malta: Delete duplicate PCI fixup.
MIPS: ath79: don't hardcode the unavailability of the DSP ASE
MIPS: Synchronize MIPS count one CPU at a time
MIPS: BCM63xx: Fix SPI message control register handling for BCM6338/6348.
MIPS: Module: Deal with malformed HI16/LO16 relocation sequences.
MIPS: Fix race condition in module relocation code.
MIPS: Fix memory leak in error path of HI16/LO16 relocation handling.
MIPS: MTX-1: Add udelay to mtx1_pci_idsel
MIPS: ath79: select HAVE_CLK
MIPS: ath79: Use correct IRQ number for the OHCI controller on AR7240
MIPS: ath79: Fix number of GPIO lines for AR724[12]
MIPS: Octeon: Fix broken interrupt controller code.
Pull block-related fixes from Jens Axboe:
- Improvements to the buffered and direct write IO plugging from
Fengguang.
- Abstract out the mapping of a bio in a request, and use that to
provide a blk_bio_map_sg() helper. Useful for mapping just a bio
instead of a full request.
- Regression fix from Hugh, fixing up a patch that went into the
previous release cycle (and marked stable, too) attempting to prevent
a loop in __getblk_slow().
- Updates to discard requests, fixing up the sizing and how we align
them. Also a change to disallow merging of discard requests, since
that doesn't really work properly yet.
- A few drbd fixes.
- Documentation updates.
* 'for-linus' of git://git.kernel.dk/linux-block:
block: replace __getblk_slow misfix by grow_dev_page fix
drbd: Write all pages of the bitmap after an online resize
drbd: Finish requests that completed while IO was frozen
drbd: fix drbd wire compatibility for empty flushes
Documentation: update tunable options in block/cfq-iosched.txt
Documentation: update tunable options in block/cfq-iosched.txt
Documentation: update missing index files in block/00-INDEX
block: move down direct IO plugging
block: remove plugging at buffered write time
block: disable discard request merge temporarily
bio: Fix potential memory leak in bio_find_or_create_slab()
block: Don't use static to define "void *p" in show_partition_start()
block: Add blk_bio_map_sg() helper
block: Introduce __blk_segment_map_sg() helper
fs/block-dev.c:fix performance regression in O_DIRECT writes to md block devices
block: split discard into aligned requests
block: reorganize rounding of max_discard_sectors
2) additional or corrected drive quirks for ata_blacklist
3) Kconfig text tweaking
4) new PCI IDs
5) pata_atiixp: quirk for MSI motherboard
6) export ahci_dev_classify for an ahci_platform driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=pjUK
-----END PGP SIGNATURE-----
Merge tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
Pull libata fixes from Jeff Garzik:
- libata-acpi regression fix
- additional or corrected drive quirks for ata_blacklist
- Kconfig text tweaking
- new PCI IDs
- pata_atiixp: quirk for MSI motherboard
- export ahci_dev_classify for an ahci_platform driver
* tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: Add a space to " 2GB ATA Flash Disk" DMA blacklist entry
[libata] new quirk, lift bridge limits for Buffalo DriveStation Quattro
[libata] Kconfig: Elaborate that SFF is meant for legacy and PATA stuff
[libata] acpi: call ata_acpi_gtm during ata port init time
ata_piix: Add Device IDs for Intel Lynx Point-LP PCH
ahci: Add Device IDs for Intel Lynx Point-LP PCH
pata_atiixp: override cable detection on MSI E350DM-E33
ahci: un-staticize ahci_dev_classify
commit d70e551c8e, Add " 2GB ATA Flash
Disk"/"ADMA428M" to DMA blacklist, should have added a space before 2GB.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Ben Hutchings says:
====================
Simple fix for a braino. Please also queue this for the 3.4 and 3.5
stable series.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde says:
====================
here are two fixes for the v3.6 release cycle. Alexey Khoroshilov submitted a
fix for a memory leak in the softing driver (in softing_load_fw()) in case a
krealloc() fails. Sven Schmitt fixed the misuse of the IRQF_SHARED flag in the
irq resouce of the sja1000 platform driver, now the correct flag is used. There
are no mainline users of this feature which need to be converted.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
This batch of fixes is intended for 3.6...
Johannes Berg gives us a pair of iwlwifi fixes. One corrects some
improperly defined ifdefs that lead to crashes and BUG_ONs. The other
prevents attempts to read SRAM for devices that aren't actually started.
Julia Lawall provides an ipw2100 fix to properly set the return code
from a function call before testing it! :-)
Thomas Huehn corrects the improper use of a constant related to a power
setting in ath5k.
Thomas Pedersen offers a mac80211 fix to properly handle destination
addresses of unicast frames passing though a mesh gate.
Vladimir Zapolskiy provides a brcmsmac fix to properly mark the
interface state when the device goes down.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds "#ifndef __<header>_H" for protecting header from double
inclusion.
Signed-off-by: Rayagond Kokatanur <rayagond@vayavyalabs.com>
Hacked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This board is incorrectly detected as having an LVDS connector,
resulting in the VGA output (the only available output on the board)
showing the console only in the top-left 1024x768 pixels, and an extra
LVDS connector appearing in X.
It's a desktop Mini-ITX board using an Atom D525 CPU with an NM10
chipset.
I've had this board for about a year, but this is the first time I
noticed the issue because I've been running it headless for most of its
life.
Signed-off-by: Calvin Walton <calvin.walton@kepstin.ca>
The current layout is to place the per-process tables at the end of the
GTT. However, this is currently using a hardcoded maximum size for the GTT
and not taking in account limitations imposed by the BIOS. Use the value
for the total number of entries allocated in the table as provided by
the configuration registers.
Reported-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Matthew Garret <mjg@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The sja1000 platform driver wrongly assumes that a shared IRQ is indicated
with the IRQF_SHARED flag in irq resource flags. This patch changes the
driver to handle the correct flag IORESOURCE_IRQ_SHAREABLE instead.
There are no mainline users of the platform driver which wrongly make use
of IRQF_SHARED.
Signed-off-by: Sven Schmitt <sven.schmitt@volkswagen.de>
Acked-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Do not leak memory by updating pointer with potentially NULL realloc return value.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Pull crypto fixes from Herbert Xu:
"This push fixes a build error on 32-bit archs in the hifn driver as
well as a potential deadlock in the caam driver."
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: caam - fix possible deadlock condition
crypto: hifn_795x - fix 64bit division and undefined __divdi3 on 32bit archs
Pull IDE power management bugfix from David S. Miller.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide:
ide: fix generic_ide_suspend/resume Oops
Pull HID fix from Jiri Kosina:
"Fix for one particular device not being properly claimed by
hid-multitouch driver"
* 'upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: Remove QUANTA from special drivers list
ETHTOOL_GRXCLSRULE returns filters for a TCP/IPv4 or UDP/IPv4 4-tuple
with source and destination swapped.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
If we try to print to the console device while its decoding is disabled,
the system will hang.
Reported-and-tested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Olof Johansson <olof@lixom.net>
* 'imx/fixes-for-3.6' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: dts: imx51-babbage: fix esdhc cd/wp properties
ARM: imx6: spin the cpu until hardware takes it down
ARM i.MX6q: Add virtual 1/3.5 dividers in the LDB clock path
Also updates to Linux 3.6-rc2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
AT91_ID_SYS as virq is incorrect because of spare irq support which
introduces NR_IRQS_LEGACY offset. It modifies rtc-at91sam9 driver in
order to get irq from resources.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
omapfb does not currently set pseudo palette correctly for color depths
above 16bpp, making red text invisible, command like
echo -e '\e[0;31mRED' > /dev/tty1
will display nothing on framebuffer console in 24bpp mode.
This is because temporary variable is declared incorrectly, fix it.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Cc: stable@vger.kernel.org # v3.x
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Commit f476ae9dab (OMAPDSS: APPLY: Remove
DISPC writes to manager's lcd parameters in interface) broke the SDI
output, as it causes the SDI PLL locking to fail.
LCLK and PCLK divisors are located in shadow registers, and we normally
write them to DISPC registers when enabling the output. However, SDI
uses pck-free as source clock for its PLL, and pck-free is affected by
the divisors. And as we need the PLL before enabling the output, we need
to write the divisors early.
It seems just writing to the DISPC register is enough, and we don't need
to care about the shadow register mechanism for pck-free. The exact
reason for this is unknown.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Do a sanity check on these before using them as divisors.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Using kfree to free data allocated with devm_kzalloc causes double frees.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x;
@@
x = devm_kzalloc(...)
...
?-kfree(x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This is already fixed for ILK and SNB in the below commit but somehow
IVB is missed.
commit ab2f9df10d
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Mon Feb 27 12:40:10 2012 -0800
drm/i915: fix color order for BGR formats on SNB
Had the wrong bits and field definitions.
Signed-off-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Wrong order of parameters passed-in when calling hdmi/adpa
/lvds_pipe_enabled(), 2nd and 3rd parameters are reversed.
This bug was indroduced by
commit 1519b9956e
Author: Keith Packard <keithp@keithp.com>
Date: Sat Aug 6 10:35:34 2011 -0700
drm/i915: Fix PCH port pipe select in CPT disable paths
The reachable tag for this commit is v3.1-rc1-3-g1519b99
Signed-off-by: Anhua Xu <anhua.xu@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=44876
Tested-by: Daniel Schroeder <sec@dschroeder.info>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The old interface is bugged and reads the wrong sensor when retrieving
the reading for the chassis fan (it reads the CPU sensor); the new
interface works fine.
Reported-by: Göran Uddeborg <goeran@uddeborg.se>
Cc: stable@vger.kernel.org
Tested-by: Göran Uddeborg <goeran@uddeborg.se>
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch fixes the name of the macro used to mask the
mmc interrupt: erroneously it was used: MMC_DEFAUL_MASK.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Erroneously the DWMAC_CORE_3_40 was set to 34 instead of 0x34.
This can generate problems when run on old chips because
the driver assumes that there are the extra 16 regs available
for perfect filtering.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Gianni Antoniazzi <gianni.antoniazzi-ext@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change marks interface as down on reset, otherwise the driver can't
reinitialize itself properly.
Without the change a transient problem turns out to be critical and leads
to inavailability to reset the driver without brcmsmac module unload/load
cycle:
ieee80211 phy0: wl0: PSM microcode watchdog fired at 5993 (seconds). Resetting.
brcms_c_dpc : PSM Watchdog, chipid 0xa8d9, chiprev 0x1
ieee80211 phy0: wl0: fatal error, reinitializing
ieee80211 phy0: Hardware restart was requested
ieee80211 phy0: brcms_ops_start: brcms_up() returned -19
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pull drm fixes from Dave Airlie:
"Intel: edid fixes, power consumption fix, s/r fix, haswell fix
Radeon: BIOS loading fixes for UEFI and Thunderbolt machines, better
MSAA validation, lockup timeout fixes, modesetting fixes
One udl dpms fix, one vmwgfx fix, a couple of trivial core changes.
There is an export added to ACPI as part of the radeon bios fixes.
I've also included the fbcon flashing cursor vs deinit race fix, that
seems the simplest place to start"
Trivial conflict in drivers/video/console/fbcon.c due to me having
already applied the fbcon flashing cursor vs deinit race fix, and Dave
had added a comment in there too.
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (22 commits)
fbcon: fix race condition between console lock and cursor timer (v1.1)
drm: Add missing static storage class specifiers in drm_proc.c file
drm/udl: dpms off the crtc when disabled.
drm: Remove two unused fields from struct drm_display_mode
drm: stop vmgfx driver explosion
drm/radeon/ss: use num_crtc rather than hardcoded 6
Revert "drm/radeon: fix bo creation retry path"
drm/i915: use hsw rps tuning values everywhere on gen6+
drm/radeon: split ATRM support out from the ATPX handler (v3)
drm/radeon: convert radeon vfct code to use acpi_get_table_with_size
ACPI: export symbol acpi_get_table_with_size
drm/radeon: implement ACPI VFCT vbios fetch (v3)
drm/radeon/kms: extend the Fujitsu D3003-S2 board connector quirk to cover later silicon stepping
drm/radeon: fix checking of MSAA renderbuffers on r600-r700
drm/radeon: allow CMASK and FMASK in the CS checker on r600-r700
drm/radeon: init lockup timeout on ring init
drm/radeon: avoid turning off spread spectrum for used pll
drm/i915: fall back to bit-banging if GMBUS fails in CRT EDID reads
drm/i915: extract connector update from intel_ddc_get_modes() for reuse
drm/i915: fix hsw uncached pte
...
Pull SCSI target fixes from Nicholas Bellinger:
"The executive summary includes:
- Post-merge review comments for tcm_vhost (MST + nab)
- Avoid debugging overhead when not debugging for tcm-fc(FCoE) (MDR)
- Fix NULL pointer dereference bug on alloc_page failulre (Yi Zou)
- Fix REPORT_LUNs regression bug with pSCSI export (AlexE + nab)
- Fix regression bug with handling of zero-length data CDBs (nab)
- Fix vhost_scsi_target structure alignment (MST)
Thanks again to everyone who contributed a bugfix patch, gave review
feedback on tcm_vhost code, and/or reported a bug during their own
testing over the last weeks.
There is one other outstanding bug reported by Roland recently related
to SCSI transfer length overflow handling, for which the current
proposed bugfix has been left in queue pending further testing with
other non iscsi-target based fabric drivers.
As the patch is verified with loopback (local SGL memory from SCSI
LLD) + tcm_qla2xxx (TCM allocated SGL memory mapped to PCI HW) fabric
ports, it will be included into the next 3.6-rc-fixes PULL request."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: Remove unused se_cmd.cmd_spdtl
tcm_fc: rcu_deref outside rcu lock/unlock section
tcm_vhost: Fix vhost_scsi_target structure alignment
target: Fix regression bug with handling of zero-length data CDBs
target/pscsi: Fix bug with REPORT_LUNs handling for SCSI passthrough
tcm_vhost: Change vhost_scsi_target->vhost_wwpn to char *
target: fix NULL pointer dereference bug alloc_page() fails to get memory
tcm_fc: Avoid debug overhead when not debugging
tcm_vhost: Post-merge review changes requested by MST
tcm_vhost: Fix incorrect IS_ERR() usage in vhost_scsi_map_iov_to_sgl
Pull i2c-embedded fixes from Wolfram Sang:
"Some bugfixes for the "embedded" part of the I2C subsystem. The fixes
affect mostly drivers which have been largely reworked lately and
where regressions appeared."
* 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux:
i2c: tegra: protect suspend/resume callbacks with CONFIG_PM_SLEEP
i2c: diolan-u2c: Fix master_xfer return code
I2C: OMAP: xfer: fix runtime PM get/put balance on error
i2c: nomadik: Add default configuration into the Nomadik I2C driver
These patches fix the Samsung PWM driver and perform some minor cleanups
like fixing checkpatch and sparse warnings. Two redundant error messages
are removed and the Kconfig help text for the PWM subsystem is made more
descriptive.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=oTl5
-----END PGP SIGNATURE-----
Merge tag 'for-3.6-rc3' of git://gitorious.org/linux-pwm/linux-pwm
Pull pwm fixes from Thierry Reding:
"These patches fix the Samsung PWM driver and perform some minor
cleanups like fixing checkpatch and sparse warnings.
Two redundant error messages are removed and the Kconfig help text for
the PWM subsystem is made more descriptive."
* tag 'for-3.6-rc3' of git://gitorious.org/linux-pwm/linux-pwm:
pwm: Improve Kconfig help text
pwm: core: Fix coding style issues
pwm: vt8500: Fix coding style issue
pwm: Remove a redundant error message when devm_request_and_ioremap fails
pwm: samsung: add missing device pointer to struct pwm_chip
pwm: Add missing static storage class specifiers in core.c file
Pull assorted fixes - mostly vfs - from Al Viro:
"Assorted fixes, with an unexpected detour into vfio refcounting logics
(fell out when digging in an analog of eventpoll race in there)."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
task_work: add a scheduling point in task_work_run()
fs: fix fs/namei.c kernel-doc warnings
eventpoll: use-after-possible-free in epoll_create1()
vfio: grab vfio_device reference *before* exposing the sucker via fd_install()
vfio: get rid of vfio_device_put()/vfio_group_get_device* races
vfio: get rid of open-coding kref_put_mutex
introduce kref_put_mutex()
vfio: don't dereference after kfree...
mqueue: lift mnt_want_write() outside ->i_mutex, clean up a bit
This QUANTA device is driven by the generic hid-multitouch.ko driver, and
therefore shouldn't be in the special drivers list.
This has been an oversight in 4fa3a58 ("HID: hid-multitouch: Switch to
device groups").
Signed-off-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It's not critical (anymore) since another thread closing the file will block
on ->device_lock before it gets to dropping the final reference, but it's
definitely cleaner that way...
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
we really need to make sure that dropping the last reference happens
under the group->device_lock; otherwise a loop (under device_lock)
might find vfio_device instance that is being freed right now, has
already dropped the last reference and waits on device_lock to exclude
the sucker from the list.
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Adds support for the EMR digitizer on the Cintiq 24HD touch. The
EMR digitizer should work identically to that found on the Cintiq
24HD. The touch digitizer is a separate USB device similar to how
we split apart some other devices.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
They all define their chassis type as "Other" and therefore are not
categorized as "laptops" by the driver, which tries to perform AUX IRQ
delivery test which fails and causes touchpad not working.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=42620
Cc: stable@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Ensure the hardware is correctly initialized before requesting the
interrupt, otherwise if a key was already touched since power-on the
kernel enters an interrupt loop. To fix this issue we clear pending
interrupt sources. We also have to make sure clk is enabled while
changing the keypad registers.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This fixes the following breakage:
edt-ft5x06.c: In function edt_ft5x06_ts_remove:
edt-ft5x06.c:846:14: error: struct edt_ft5x06_ts_data has no member named
raw_buffer
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Simon Budig <simon.budig@kernelconcepts.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
So we've had a fair few reports of fbcon handover breakage between
efi/vesafb and i915 surface recently, so I dedicated a couple of
days to finding the problem.
Essentially the last thing we saw was the conflicting framebuffer
message and that was all.
So after much tracing with direct netconsole writes (printks
under console_lock not so useful), I think I found the race.
Thread A (driver load) Thread B (timer thread)
unbind_con_driver -> |
bind_con_driver -> |
vc->vc_sw->con_deinit -> |
fbcon_deinit -> |
console_lock() |
| |
| fbcon_flashcursor timer fires
| console_lock() <- blocked for A
|
|
fbcon_del_cursor_timer ->
del_timer_sync
(BOOM)
Of course because all of this is under the console lock,
we never see anything, also since we also just unbound the active
console guess what we never see anything.
Hopefully this fixes the problem for anyone seeing vesafb->kms
driver handoff.
v1.1: add comment suggestion from Alan.
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Merge fixes from Andrew Morton.
Random drivers and some VM fixes.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (17 commits)
mm: compaction: Abort async compaction if locks are contended or taking too long
mm: have order > 0 compaction start near a pageblock with free pages
rapidio/tsi721: fix unused variable compiler warning
rapidio/tsi721: fix inbound doorbell interrupt handling
drivers/rtc/rtc-rs5c348.c: fix hour decoding in 12-hour mode
mm: correct page->pfmemalloc to fix deactivate_slab regression
drivers/rtc/rtc-pcf2123.c: initialize dynamic sysfs attributes
mm/compaction.c: fix deferring compaction mistake
drivers/misc/sgi-xp/xpc_uv.c: SGI XPC fails to load when cpu 0 is out of IRQ resources
string: do not export memweight() to userspace
hugetlb: update hugetlbpage.txt
checkpatch: add control statement test to SINGLE_STATEMENT_DO_WHILE_MACRO
mm: hugetlbfs: correctly populate shared pmd
cciss: fix incorrect scsi status reporting
Documentation: update mount option in filesystem/vfat.txt
mm: change nr_ptes BUG_ON to WARN_ON
cs5535-clockevt: typo, it's MFGPT, not MFPGT
Pull media fixes from Mauro Carvalho Chehab:
"For bug fixes, at soc_camera, si470x, uvcvideo, iguanaworks IR driver,
radio_shark Kbuild fixes, and at the V4L2 core (radio fixes)."
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] media: soc_camera: don't clear pix->sizeimage in JPEG mode
[media] media: mx2_camera: Fix clock handling for i.MX27
[media] video: mx2_camera: Use clk_prepare_enable/clk_disable_unprepare
[media] video: mx1_camera: Use clk_prepare_enable/clk_disable_unprepare
[media] media: mx3_camera: buf_init() add buffer state check
[media] radio-shark2: Only compile led support when CONFIG_LED_CLASS is set
[media] radio-shark: Only compile led support when CONFIG_LED_CLASS is set
[media] radio-shark*: Call cancel_work_sync from disconnect rather then release
[media] radio-shark*: Remove work-around for dangling pointer in usb intfdata
[media] Add USB dependency for IguanaWorks USB IR Transceiver
[media] Add missing logging for rangelow/high of hwseek
[media] VIDIOC_ENUM_FREQ_BANDS fix
[media] mem2mem_testdev: fix querycap regression
[media] si470x: v4l2-compliance fixes
[media] DocBook: Remove a spurious character
[media] uvcvideo: Reset the bytesused field when recycling an erroneous buffer
Pull networking update from David Miller:
"A couple weeks of bug fixing in there. The largest chunk is all the
broken crap Amerigo Wang found in the netpoll layer."
1) netpoll and it's users has several serious bugs:
a) uses GFP_KERNEL with locks held
b) interfaces requiring interrupts disabled are called with them
enabled
c) and vice versa
d) VLAN tag demuxing, as per all other RX packet input paths, is not
applied
All from Amerigo Wang.
2) Hopefully cure the ipv4 mapped ipv6 address TCP early demux bugs for
good, from Neal Cardwell.
3) Unlike AF_UNIX, AF_PACKET sockets don't set a default credentials
when the user doesn't specify one explicitly during sendmsg().
Instead we attach an empty (zero) SCM credential block which is
definitely not what we want. Fix from Eric Dumazet.
4) IPv6 illegally invokes netdevice notifiers with RCU lock held, fix
from Ben Hutchings.
5) inet_csk_route_child_sock() checks wrong inet options pointer, fix
from Christoph Paasch.
6) When AF_PACKET is used for transmit, packet loopback doesn't behave
properly when a socket fanout is enabled, from Eric Leblond.
7) On bluetooth l2cap channel create failure, we leak the socket, from
Jaganath Kanakkassery.
8) Fix all the netprio file handling bugs found by Al Viro, from John
Fastabend.
9) Several error return and NULL deref bug fixes in networking drivers
from Julia Lawall.
10) A large smattering of struct padding et al. kernel memory leaks to
userspace found of Mathias Krause.
11) Conntrack expections in netfilter can access an uninitialized timer,
fix from Pablo Neira Ayuso.
12) Several netfilter SIP tracker bug fixes from Patrick McHardy.
13) IPSEC ipv6 routes are not initialized correctly all the time,
resulting in an OOPS in inet_putpeer(). Also from Patrick McHardy.
14) Bridging does rcu_dereference() outside of RCU protected area, from
Stephen Hemminger.
15) Fix routing cache removal performance regression when looking up
output routes that have a local destination. From Zheng Yan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (87 commits)
af_netlink: force credentials passing [CVE-2012-3520]
ipv4: fix ip header ident selection in __ip_make_skb()
ipv4: Use newinet->inet_opt in inet_csk_route_child_sock()
tcp: fix possible socket refcount problem
net: tcp: move sk_rx_dst_set call after tcp_create_openreq_child()
net/core/dev.c: fix kernel-doc warning
netconsole: remove a redundant netconsole_target_put()
net: ipv6: fix oops in inet_putpeer()
net/stmmac: fix issue of clk_get for Loongson1B.
caif: Do not dereference NULL in chnl_recv_cb()
af_packet: don't emit packet on orig fanout group
drivers/net/irda: fix error return code
drivers/net/wan/dscc4.c: fix error return code
drivers/net/wimax/i2400m/fw.c: fix error return code
smsc75xx: add missing entry to MAINTAINERS
net: qmi_wwan: new devices: UML290 and K5006-Z
net: sh_eth: Add eth support for R8A7779 device
netdev/phy: skip disabled mdio-mux nodes
dt: introduce for_each_available_child_of_node, of_get_next_available_child
net: netprio: fix cgrp create and write priomap race
...
Fix unused variable compiler warning when built with CONFIG_RAPIDIO_DEBUG
option off.
This patch is applicable to kernel versions starting from v3.2
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make sure that there is no doorbell messages left behind due to disabled
interrupts during inbound doorbell processing.
The most common case for this bug is loss of rionet JOIN messages in
systems with three or more rionet participants and MSI or MSI-X enabled.
As result, requests for packet transfers may finish with "destination
unreachable" error message.
This patch is applicable to kernel versions starting from v3.2.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Correct the offset by subtracting 20 from tm_hour before taking the
modulo 12.
[ "Why 20?" I hear you ask. Or at least I did.
Here's the reason why: RS5C348_BIT_PM is 32, and is - stupidly -
included in the RS5C348_HOURS_MASK define. So it's really subtracting
out that bit to get "hour+12". But then because it does things modulo
12, it needs to add the 12 in again afterwards anyway.
This code is confused. It would be much clearer if RS5C348_HOURS_MASK
just didn't include the RS5C348_BIT_PM bit at all, then it wouldn't
need to do the silly subtract either.
Whatever. It's all just math, the end result is the same. - Linus ]
Reported-by: James Nute <newten82@gmail.com>
Tested-by: James Nute <newten82@gmail.com>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dynamically allocated sysfs attributes must be initialized using
sysfs_attr_init(), otherwise lockdep complains: BUG: key <address> not in
.data!
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Ilya Shchepetkov <shchepetkov@ispras.ru>
Cc: Chris Verges <chrisv@cyberswitching.com>
Cc: Christian Pellegrin <chripell@fsfe.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On many of our larger systems, CPU 0 has had all of its IRQ resources
consumed before XPC loads. Worst cases on machines with multiple 10
GigE cards and multiple IB cards have depleted the entire first socket
of IRQs.
This patch makes selecting the node upon which IRQs are allocated (as
well as all the other GRU Message Queue structures) specifiable as a
module load param and has a default behavior of searching all nodes/cpus
for an available resources.
[akpm@linux-foundation.org: fix build: include cpu.h and module.h]
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Delete code which sets SCSI status incorrectly as it's already been set
correctly above this incorrect code. The bug was introduced in 2009 by
commit b0e15f6db1 ("cciss: fix typo that causes scsi status to be
lost.")
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Reported-by: Roel van Meer <roel.vanmeer@bokxing.nl>
Tested-by: Roel van Meer <roel.vanmeer@bokxing.nl>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes the following bug:
http://marc.info/?l=linux-pci&m=134338059022620&w=2
Where lspci does not work properly if a device and the corresponding
parent bridge (such as PCIe port) is suspended. This is because the
device configuration space registers will be not accessible if the
corresponding parent bridge is suspended or the device is put into
D3cold state.
To solve the issue, the bridge/PCIe port connected to the device is
put into active state before read/write configuration space registers.
If the device is in D3cold state, it will be put into active state
too.
To avoid resume/suspend PCIe port for each configuration register
read/write, a small delay is added before the PCIe port to go
suspended.
Reported-by: Bjorn Mork <bjorn@mork.no>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch fixes the following bug:
http://marc.info/?l=linux-pci&m=134329923124234&w=2
The root cause of the bug is as follow.
If a device is not bound with the corresponding driver, the device
runtime PM will be disabled and the device will be put into suspended
state. So that, the bridge/PCIe port connected to it may be put into
suspended and low power state. When do probing for the device later,
because the bridge/PCIe port connected to it is in low power state,
the IO access to device may fail.
To solve the issue, the bridge/PCIe port connected to the device is
put into active state before probing.
Reported-by: Bjorn Mork <bjorn@mork.no>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch fixes the following bug:
http://marc.info/?l=linux-usb&m=134318961120825&w=2
Originally, device lower power states include D1, D2, D3. After that,
D3 is further divided into D3hot and D3cold. To support both scenario
safely, original D3 is mapped to D3cold.
When adding D3cold support, because worry about some device may have
broken D3cold support, D3cold is disabled by default. This disable D3
on original platform too. But some original platform may only have
working D3, but no working D1, D2. The root cause of the above bug is
it too.
To deal with this, this patch enables D3/D3cold by default for most
devices. This restores the original behavior. For some devices that
suspected to have broken D3cold support, such as PCIe port, D3cold is
disabled by default.
Reported-by: Bjorn Mork <bjorn@mork.no>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Fixes the following sparse warning:
drivers/gpu/drm/drm_proc.c:92:5:
warning: symbol 'drm_proc_create_files' was not declared. Should it be static?
drivers/gpu/drm/drm_proc.c:175:5:
warning: symbol 'drm_proc_remove_files' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This turns off the crtc when its been disabled,
fixes it not turning off properly the whole time.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
If you do a page flip with no flags set then event is NULL. If event is
NULL then the vmw_gfx driver likes to go digging into NULL and extracts
NULL->base.file_priv.
On a modern kernel with NULL mapping protection it's just another oops,
without it there are some "intriguing" possibilities.
What it should do is an open question but that for the driver owners to
sort out.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Daniel writes:
" Nothing too major:
- A few fixes around the edid handling from Jani, also fixing a regression
in 3.5 due to us using gmbus by default.
- Fixup hsw uncached pte flags.
- Fix suspend/resume crash when using hw contexts, from Ben.
- Try to tune gpu turbo a bit better, seems to help with some oddball
power regressions."
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: use hsw rps tuning values everywhere on gen6+
drm/i915: fall back to bit-banging if GMBUS fails in CRT EDID reads
drm/i915: extract connector update from intel_ddc_get_modes() for reuse
drm/i915: fix hsw uncached pte
drm/i915/contexts: fix list corruption
drm/i915: fix EDID memory leak in SDVO
Alex writes:
"This is the current set of radeon fixes for 3.6. Nothing too major.
Highlights:
- fix vbios fetch on pure uefi systems
- fix vbios fetch on thunderbolt systems
- MSAA fixes
- lockup timeout fix
- modesetting fix"
* 'drm-fixes-3.6' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon/ss: use num_crtc rather than hardcoded 6
Revert "drm/radeon: fix bo creation retry path"
drm/radeon: split ATRM support out from the ATPX handler (v3)
drm/radeon: convert radeon vfct code to use acpi_get_table_with_size
ACPI: export symbol acpi_get_table_with_size
drm/radeon: implement ACPI VFCT vbios fetch (v3)
drm/radeon/kms: extend the Fujitsu D3003-S2 board connector quirk to cover later silicon stepping
drm/radeon: fix checking of MSAA renderbuffers on r600-r700
drm/radeon: allow CMASK and FMASK in the CS checker on r600-r700
drm/radeon: init lockup timeout on ring init
drm/radeon: avoid turning off spread spectrum for used pll
Merav Sicron
