Add minimal device tree source needed for DRA7 based SoCs.
Also add a board dts file for the dra7-evm (based on dra752)
which contains 1.5G of memory with 1G interleaved and 512MB
non-interleaved. Also added in the board file are pin configuration
details for i2c, mcspi and uart devices on board.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The OMAP4 SoC family uses specially-designed PMIC (power management IC)
companion chip for power management needs: TWL6030/TWL6032.
Therefore there is a typical connection of PMIC to OMAP4 so we can
move it into separate .dtsi file and do not duplicate over
board-specific files.
Tested on OMAP4 SDP board and Pandaboard ES2.
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
SMPS10 has two outputs OUT1 and OUT2. Hence SMPS10 is modeled as
two regulators. The DT node is split to reflect it.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Following commit ff5c9059 and therefore other omap platforms using
the gpio-omap driver correct the #interrupt-cells property on am33xx
too. The omap gpio binding documentaion also states that
the #interrupt-cells property should be 2.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
ARM Performance Monitor Units are available on the am33xx,
add the support in the dtsi.
Tested with perf and oprofile on a regular beaglebone.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The IGEP COM MOdule has a GPIO LED connected to OMAP
pins. Configure this pin as output GPIO.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The IGEPv2 has a number of GPIO LED connected to OMAP
pins. Configure these pins as output GPIO.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
IGEP boards have a number of LED connected to OMAP or TWL GPIO
lines. The actual wiring is different on each board so each board
DT has need to configure the mux correctly.
Even though it works with the current DT, the kernel complains with:
[2.305023] leds-gpio leds.18: pins are not configured from the driver
Add an empty pinmux_leds_pins pinctrl child node so boards can
override with the correct mux configuration and not depend on
default values for the GPIO LEDs to work.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
This adds device tree with necessary support to boot with functional
video (on both emulator and real N900 device).
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Currently hdmi_setup_audio_infoframe() reprograms the HDA channel
mapping only when the infoframe is not up-to-date or the non-PCM flag
has changed.
However, when just the channel map has been changed, the infoframe may
still be up-to-date and non-PCM flag may not have changed, so the new
channel map is not actually programmed into the HDA codec.
Notably, this failing case is also always triggered when the device is
already in a prepared state and a new channel map is configured while
changing only the channel positions (for example, plain
"speaker-test -c2 -m FR,FL").
Fix that by always programming the channel map in
hdmi_setup_audio_infoframe(). Tested on Intel HDMI.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
. The libaudit test was failing in some systems due to a unescaped newline, fix
it so that the 'trace' tool can be built in such systems.
. Fix installation of libexec components.
. Add default handler for mmap2 events so that tools that don't explicitely
define an MMAP2 handler don't crash, fix from David Ahern.
. Fix to find line information for probe list, from Masami Hiramatsu.
. Set child_pid after perf_evlist__prepare_workload(), fix from Namhyung Kim.
. Fix infinite loop on invalid perf.data file, from Namhyung Kim.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=OgDk
-----END PGP SIGNATURE-----
Merge tag 'perf-urgent-for-mingo' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Pull perf/urgent fixes from Arnaldo Carvalho de Melo:
* The libaudit test was failing in some systems due to a unescaped newline, fix
it so that the 'trace' tool can be built in such systems.
* Fix installation of libexec components.
* Add default handler for mmap2 events so that tools that don't explicitely
define an MMAP2 handler don't crash, fix from David Ahern.
* Fix to find line information for probe list, from Masami Hiramatsu.
* Set child_pid after perf_evlist__prepare_workload(), fix from Namhyung Kim.
* Fix infinite loop on invalid perf.data file, from Namhyung Kim.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
irq_exit() is now called on the irq stack, which can trigger a switch to
the softirq stack from the irq stack. If an interrupt happens at that
point, we will not properly detect the re-entrancy and clobber the
original return context on the irq stack.
This fixes it. The side effect is to prevent all nesting from softirq
stack to irq stack even in the "safe" case but it's simpler that way and
matches what x86_64 does.
Reported-by: Cédric Le Goater <clg@fr.ibm.com>
Tested-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull HID fixes from Jiri Kosina:
- fix for hidraw reference counting regression, by Manoj Chourasia
- fix for minor number allocation for uhid, by David Herrmann
- other small unsorted fixes / device ID additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: wiimote: fix FF deadlock
HID: add Holtek USB ID 04d9:a081 SHARKOON DarkGlider
HID: hidraw: close underlying device at removal of last reader
HID: roccat: Fix "cannot create duplicate filename" problems
HID: uhid: allocate static minor
Pull Tile bugfixes from Chris Metcalf:
"This fixes some serious issues with PREEMPT support, and a couple of
smaller corner-case issues fixed in the last couple of weeks"
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
arch: tile: re-use kbasename() helper
tile: use a more conservative __my_cpu_offset in CONFIG_PREEMPT
tile: ensure interrupts disabled for preempt_schedule_irq()
tile: change lock initalization in hardwall
tile: include: asm: use 'long long' instead of 'u64' for atomic64_t and its related functions
The input core has an internal spinlock that is acquired during event
injection via input_event() and friends but also held during FF callbacks.
That means, there is no way to share a lock between event-injection and FF
handling. Unfortunately, this is what is required for wiimote state
tracking and what we do with state.lock and input->lock.
This deadlock can be triggered when using continuous data reporting and FF
on a wiimote device at the same time. I takes me at least 30m of
stress-testing to trigger it but users reported considerably shorter
times (http://bpaste.net/show/132504/) when using some gaming-console
emulators.
The real problem is that we have two copies of internal state, one in the
wiimote objects and the other in the input device. As the input-lock is
not supposed to be accessed from outside of input-core, we have no other
chance than offloading FF handling into a worker. This actually works
pretty nice and also allows to implictly merge fast rumble changes into a
single request.
Due to the 3-layered workers (rumble+queue+l2cap) this might reduce FF
responsiveness. Initial tests were fine so lets fix the race first and if
it turns out to be too slow we can always handle FF out-of-band and skip
the queue-worker.
Cc: <stable@vger.kernel.org> # 3.11+
Reported-by: Thomas Schneider
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit 1400eb6 (MIPS: r4k,octeon,r2300: stack protector: change canary
per task) was merged in v3.11 and introduced assembly in the MIPS resume
functions to update the value of the current canary in
__stack_chk_guard. However it used PTR_L resulting in a load of the
canary value, instead of PTR_LA to construct its address. The value is
intended to be random but is then treated as an address in the
subsequent LONG_S (store).
This was observed to cause a fault and panic:
CPU 0 Unable to handle kernel paging request at virtual address 139fea20, epc == 8000cc0c, ra == 8034f2a4
Oops[#1]:
...
$24 : 139fea20 1e1f7cb6
...
Call Trace:
[<8000cc0c>] resume+0xac/0x118
[<8034f2a4>] __schedule+0x5f8/0x78c
[<8034f4e0>] schedule_preempt_disabled+0x20/0x2c
[<80348eec>] rest_init+0x74/0x84
[<804dc990>] start_kernel+0x43c/0x454
Code: 3c18804b 8f184030 8cb901f8 <af190000> 00c0e021 8cb002f0 8cb102f4 8cb202f8 8cb302fc
This can also be forced by modifying
arch/mips/include/asm/stackprotector.h so that the default
__stack_chk_guard value is more likely to be a bad (or unaligned)
pointer.
Fix it to use PTR_LA instead, to load the address of the canary value,
which the LONG_S can then use to write into it.
Reported-by: bobjones (via #mipslinux on IRC)
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gregory Fong <gregory.0xf0@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/6026/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
'irq' was not released when clk_prepare_enable failed.
Fix it.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
On this machine, DAC on node 0x03 seems to give mono output.
Also, it needs additional patches for headset mic support.
It supports CTIA style headsets only.
Alsa-info available at the bug link below.
Cc: stable@kernel.org (v3.10+)
BugLink: https://bugs.launchpad.net/bugs/1236228
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pull s390 fixes from Martin Schwidefsky:
"A couple of bux fixes, notable are the regression with ptrace vs
restarting system calls and the patch for kdump to be able to copy
from virtual memory"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: fix system call restart after inferior call
s390: Allow vmalloc target buffers for copy_from_oldmem()
s390/sclp: properly detect line mode console
s390/kprobes: add exrl to list of prohibited opcodes
s390/3270: fix return value check in tty3270_resize_work()
Daniel writes:
Just a few important fixes, all cc: stable (I've checked this time around
and made sure they're really there ...). The dpms one is a regression from
the modeset rework and has a good chance to rectify Linus' hdmi issues.
* tag 'drm-intel-fixes-2013-10-07' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Only apply DPMS to the encoder if enabled
drm/i915: Mask LPSP to get PSR working even with Power Well in use by audio.
drm/i915/hsw: Disable L3 caching of atomic memory operations.
drm/i915: fix rps.vlv_work initialization
Modify the code to use current_euid(), and in_egroup_p, as in done
in fs/proc/proc_sysctl.c:test_perm()
Cc: stable@vger.kernel.org
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Reported-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull SCSI target fixes from Nicholas Bellinger:
"Here are the outstanding target fixes queued up for v3.12-rc4 code.
The highlights include:
- Make vhost/scsi tag percpu_ida_alloc() use GFP_ATOMIC
- Allow sess_cmd_map allocation failure fallback to use vzalloc
- Fix COMPARE_AND_WRITE se_cmd->data_length bug with FILEIO backends
- Fixes for COMPARE_AND_WRITE callback recursive failure OOPs + non
zero scsi_status bug
- Make iscsi-target do acknowledgement tag release from RX context
- Setup iscsi-target with extra (cmdsn_depth / 2) percpu_ida tags
Also included is a iscsi-target patch CC'ed for v3.10+ that avoids
legacy wait_for_task=true release during fast-past StatSN
acknowledgement, and two other SRP target related patches that address
long-standing issues that are CC'ed for v3.3+.
Extra thanks to Thomas Glanzmann for his testing feedback with
COMPARE_AND_WRITE + EXTENDED_COPY VAAI logic"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iscsi-target; Allow an extra tag_num / 2 number of percpu_ida tags
iscsi-target: Perform release of acknowledged tags from RX context
iscsi-target: Only perform wait_for_tasks when performing shutdown
target: Fail on non zero scsi_status in compare_and_write_callback
target: Fix recursive COMPARE_AND_WRITE callback failure
target: Reset data_length for COMPARE_AND_WRITE to NoLB * block_size
ib_srpt: always set response for task management
target: Fall back to vzalloc upon ->sess_cmd_map kzalloc failure
vhost/scsi: Use GFP_ATOMIC with percpu_ida_alloc for obtaining tag
ib_srpt: Destroy cm_id before destroying QP.
target: Fix xop->dbl assignment in target_xcopy_parse_segdesc_02
Pull slave-dmaengine fixes from Vinod Koul:
"Here is the slave dmanegine fixes. We have the fix for deadlock issue
on imx-dma by Michael and Josh's edma config fix along with author
change"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: imx-dma: fix callback path in tasklet
dmaengine: imx-dma: fix lockdep issue between irqhandler and tasklet
dmaengine: imx-dma: fix slow path issue in prep_dma_cyclic
dma/Kconfig: Make TI_EDMA select TI_PRIV_EDMA
edma: Update author email address
Pull btrfs fixes from Chris Mason:
"This is a small collection of fixes, including a regression fix from
Liu Bo that solves rare crashes with compression on.
I've merged my for-linus up to 3.12-rc3 because the top commit is only
meant for 3.12. The rest of the fixes are also available in my master
branch on top of my last 3.11 based pull"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: Fix crash due to not allocating integrity data for a bioset
Btrfs: fix a use-after-free bug in btrfs_dev_replace_finishing
Btrfs: eliminate races in worker stopping code
Btrfs: fix crash of compressed writes
Btrfs: fix transid verify errors when recovering log tree
- Two patches for the OMAP driver, dealing with setting up IRQs
properly on the device tree boot path.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=ALq3
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Two patches for the OMAP driver, dealing with setting up IRQs properly
on the device tree boot path"
* tag 'gpio-v3.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio/omap: auto-setup a GPIO when used as an IRQ
gpio/omap: maintain GPIO and IRQ usage separately
Here are 9 fixes for various USB driver problems. The majority are
gadget/musb fixes, but there are some new device ids in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.21 (GNU/Linux)
iEYEABECAAYFAlJQTVYACgkQMUfUDdst+yn5AwCeL1hSBWmUUeT7GBHtcPmMroZ1
2EIAnjQULEy4EUMgj94aqfnL0ZuNDxOp
=xyGg
-----END PGP SIGNATURE-----
Merge tag 'usb-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are none fixes for various USB driver problems. The majority are
gadget/musb fixes, but there are some new device ids in here as well"
* tag 'usb-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: chipidea: add Intel Clovertrail pci id
usb: gadget: s3c-hsotg: fix can_write limit for non-periodic endpoints
usb: gadget: f_fs: fix error handling
usb: musb: dsps: do not bind to "musb-hdrc"
USB: serial: option: Ignore card reader interface on Huawei E1750
usb: musb: gadget: fix otg active status flag
usb: phy: gpio-vbus: fix deferred probe from __init
usb: gadget: pxa25x_udc: fix deferred probe from __init
usb: musb: fix otg default state
Here are 2 tty driver fixes for 3.12-rc4.
One fixes the reported regression in the n_tty code that a number of
people found recently, and the other one fixes an issue with xen
consoles that broke in 3.10.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.21 (GNU/Linux)
iEYEABECAAYFAlJQTOgACgkQMUfUDdst+ym/EQCdFJ3hmK57vr69oSndkzV5Mx2/
ZqsAn1NPAK5j3Wtkl0eoHe8HSLDu8VGC
=pqUF
-----END PGP SIGNATURE-----
Merge tag 'tty-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty fixes from Greg KH:
"Here are two tty driver fixes for 3.12-rc4.
One fixes the reported regression in the n_tty code that a number of
people found recently, and the other one fixes an issue with xen
consoles that broke in 3.10"
* tag 'tty-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
xen/hvc: allow xenboot console to be used again
tty: Fix pty master read() after slave closes
Here are 4 tiny staging and iio driver fixes for 3.12-rc4. Nothing
major, just some small fixes for reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.21 (GNU/Linux)
iEYEABECAAYFAlJQTFkACgkQMUfUDdst+ynmmACcDHkGRZ6um7GTusOcDcddk+Mu
wJIAoKBkk7gDESTvBPJRXsHl8GjIV+C4
=H+5r
-----END PGP SIGNATURE-----
Merge tag 'staging-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging fixes from Greg KH:
"Here are 4 tiny staging and iio driver fixes for 3.12-rc4. Nothing
major, just some small fixes for reported issues"
* tag 'staging-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: comedi: ni_65xx: (bug fix) confine insn_bits to one subdevice
iio:magnetometer: Bugfix magnetometer default output registers
iio: Remove debugfs entries in iio_device_unregister()
iio: amplifiers: ad8366: Remove regulator_put
Pull CIFS fixes from Steve French:
"Small set of cifs fixes. Most important is Jeff's fix that works
around disconnection problems which can be caused by simultaneous use
of user space tools (starting a long running smbclient backup then
doing a cifs kernel mount) or multiple cifs mounts through a NAT, and
Jim's fix to deal with reexport of cifs share.
I expect to send two more cifs fixes next week (being tested now) -
fixes to address an SMB2 unmount hang when server dies and a fix for
cifs symlink handling of Windows "NFS" symlinks"
* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6:
[CIFS] update cifs.ko version
[CIFS] Remove ext2 flags that have been moved to fs.h
[CIFS] Provide sane values for nlink
cifs: stop trying to use virtual circuits
CIFS: FS-Cache: Uncache unread pages in cifs_readpages() before freeing them
MMCONFIG
Revert "x86/PCI: MMCONFIG: Check earlier for MMCONFIG region at address zero"
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=LqLn
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.12-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fix from Bjorn Helgaas:
"We merged what was intended to be an MMCONFIG cleanup, but in fact,
for systems without _CBA (which is almost everything), it broke
extended config space for domain 0 and it broke all config space for
other domains.
This reverts the change"
* tag 'pci-v3.12-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
Revert "x86/PCI: MMCONFIG: Check earlier for MMCONFIG region at address zero"
This reverts commit 07f9b61c39.
07f9b61c was intended to be a cleanup that didn't change anything, but in
fact, for systems without _CBA (which is almost everything), it broke
extended config space for domain 0 and all config space for other domains.
Reference: http://lkml.kernel.org/r/20131004011806.GE20450@dangermouse.emea.sgi.com
Reported-by: Hedi Berriche <hedi@sgi.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
1) The resume part of user space driven hibernation (s2disk) is now
broken after the change that moved the creation of memory bitmaps
to after the freezing of tasks, because I forgot that the resume
utility loaded the image before freezing tasks and needed the
bitmaps for that. The fix adds special handling for that case.
2) One of recent commits changed the export of acpi_bus_get_device()
to EXPORT_SYMBOL_GPL(), which was technically correct but broke
existing binary modules using that function including one in
particularly widespread use. Change it back to EXPORT_SYMBOL().
3) The intel_pstate driver sometimes fails to disable turbo if its
no_turbo sysfs attribute is set. Fix from Srinivas Pandruvada.
4) One of recent cpufreq fixes forgot to update a check in cpufreq-cpu0
which still (incorrectly) treats non-NULL as non-error. Fix from
Philipp Zabel.
5) The SPEAr cpufreq driver uses a wrong variable type in one place
preventing it from catching errors returned by one of the functions
called by it. Fix from Sachin Kamat.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQIcBAABCAAGBQJSTvXfAAoJEKhOf7ml8uNslkkP+QGoghnGR9hScYq/0Mcnzr4b
kwkiRx54NggjzzN8Q+ejZmxNZ7UZt3q05PmHPtJk3A8gzqIMsb83jnXsZNiDiQs6
m+KBYrV5dhPZkp08X2tHJp5ijZNRULpp9QA49ulnLfVT/A+rkr5xBCK0W3ln/zL3
tJSlGJ3N7yYUXe3nMRCCNnnnAzWA+Tk8yRaMx5MnFqlQWWnyx1SGKjD/kVv0/3RA
6rlDPQEIuoCTqLKotnGIqVN2hTFPFJKc9yTrRGZ15pMjdUGHMwnHy6KMAdXy4Rdh
R1DOdf+bvPkkFiGE1D1vKOt7pdOG/cTtNkppvWZRuoGg2AMJGm5KWlrdLhlvunyt
IQXmdt/eWecNr+WzN8FiDp4LEQcI6VjEDaJ3qbjXHLH/FOupBKXYoNWpejj4bGSE
PtPmJYjNpD2vF3cdtt80ZAYSxhLutwPQksoAwyJ40++l53Ygi81BO31LWZQnDk/8
HPWOXFThmWJtT03b0sG25GpboiCpYtHEmbwQe+y+pRx7L12HBfE4StT3hmv5Z9J4
RXXB3yNq4ApXtFq1mitpiPmSVfYe+zu590m7ZUr457BpXi7MH17tzDn9nUJ2eTZl
kXwUNWiRKGjPmKYxV/ml/apClozsGMFP+XoZkYotFd0W5+SVLuhdXdtClIt4NAbD
dUkYVMm/BBBALpmH+yKw
=P4mh
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
- The resume part of user space driven hibernation (s2disk) is now
broken after the change that moved the creation of memory bitmaps to
after the freezing of tasks, because I forgot that the resume utility
loaded the image before freezing tasks and needed the bitmaps for
that. The fix adds special handling for that case.
- One of recent commits changed the export of acpi_bus_get_device() to
EXPORT_SYMBOL_GPL(), which was technically correct but broke existing
binary modules using that function including one in particularly
widespread use. Change it back to EXPORT_SYMBOL().
- The intel_pstate driver sometimes fails to disable turbo if its
no_turbo sysfs attribute is set. Fix from Srinivas Pandruvada.
- One of recent cpufreq fixes forgot to update a check in cpufreq-cpu0
which still (incorrectly) treats non-NULL as non-error. Fix from
Philipp Zabel.
- The SPEAr cpufreq driver uses a wrong variable type in one place
preventing it from catching errors returned by one of the functions
called by it. Fix from Sachin Kamat.
* tag 'pm+acpi-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: Use EXPORT_SYMBOL() for acpi_bus_get_device()
intel_pstate: fix no_turbo
cpufreq: cpufreq-cpu0: NULL is a valid regulator, part 2
cpufreq: SPEAr: Fix incorrect variable type
PM / hibernate: Fix user space driven resume regression
R Sricharan