According to AM437x TRM, Document SPRUHL7B, Revised December 2014,
Section 7.2.1 Pad Control Registers, setting bit 19 of the pad control
registers actually sets the SLEWCTRL value to slow rather than fast as
the current macro indicates. Introduce a new macro, SLEWCTRL_SLOW, that
sets the bit, and modify SLEWCTRL_FAST to 0 but keep it for
completeness.
Current users of the macro (i2c, mdio, and uart) are left unmodified as
SLEWCTRL_FAST was the macro used and actual desired state. Tested on
am437x-gp-evm with no difference in software performance seen.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to AM335x TRM, Document spruh73l, Revised February 2015,
Section 9.2.2 Pad Control Registers, setting bit 6 of the pad control
registers actually sets the SLEWCTRL value to slow rather than fast as
the current macro indicates. Introduce a new macro, SLEWCTRL_SLOW, that
sets the bit, and modify SLEWCTRL_FAST to 0 but keep it for
completeness.
Current users of the macro (i2c and mdio) are left unmodified as
SLEWCTRL_FAST was the macro used and actual desired state. Tested on
am335x-gp-evm with no difference in software performance seen.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
enhancements and fixes mostly for ARM32, ARM64, MIPS and Power-based
devices. Additionaly the framework core underwent a bit of surgery with
two major changes. The boundary between the clock core and clock
providers (e.g clock drivers) is now more well defined with dedicated
provider helper functions. struct clk no longer maps 1:1 with the
hardware clock but is a true per-user cookie which helps us tracker
users of hardware clocks and debug bad behavior. The second major change
is the addition of rate constraints for clocks. Rate ranges are now
supported which are analogous to the voltage ranges in the regulator
framework. Unfortunately these changes to the core created some
breakeage. We think we fixed it all up but for this reason there are
lots of last minute commits trying to undo the damage.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zCVK
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.20' of git://git.linaro.org/people/mike.turquette/linux
Pull clock framework updates from Mike Turquette:
"The clock framework changes contain the usual driver additions,
enhancements and fixes mostly for ARM32, ARM64, MIPS and Power-based
devices.
Additionally the framework core underwent a bit of surgery with two
major changes:
- The boundary between the clock core and clock providers (e.g clock
drivers) is now more well defined with dedicated provider helper
functions. struct clk no longer maps 1:1 with the hardware clock
but is a true per-user cookie which helps us tracker users of
hardware clocks and debug bad behavior.
- The addition of rate constraints for clocks. Rate ranges are now
supported which are analogous to the voltage ranges in the
regulator framework.
Unfortunately these changes to the core created some breakeage. We
think we fixed it all up but for this reason there are lots of last
minute commits trying to undo the damage"
* tag 'clk-for-linus-3.20' of git://git.linaro.org/people/mike.turquette/linux: (113 commits)
clk: Only recalculate the rate if needed
Revert "clk: mxs: Fix invalid 32-bit access to frac registers"
clk: qoriq: Add support for the platform PLL
powerpc/corenet: Enable CLK_QORIQ
clk: Replace explicit clk assignment with __clk_hw_set_clk
clk: Add __clk_hw_set_clk helper function
clk: Don't dereference parent clock if is NULL
MIPS: Alchemy: Remove bogus args from alchemy_clk_fgcs_detr
clkdev: Always allocate a struct clk and call __clk_get() w/ CCF
clk: shmobile: div6: Avoid division by zero in .round_rate()
clk: mxs: Fix invalid 32-bit access to frac registers
clk: omap: compile legacy omap3 clocks conditionally
clkdev: Export clk_register_clkdev
clk: Add rate constraints to clocks
clk: remove clk-private.h
pci: xgene: do not use clk-private.h
arm: omap2+ remove dead clock code
clk: Make clk API return per-user struct clk instances
clk: tegra: Define PLLD_DSI and remove dsia(b)_mux
clk: tegra: Add support for the Tegra132 CAR IP block
...
Pull more thermal managament updates from Zhang Rui:
"Specifics:
- Exynos thermal driver refactoring. Several cleanups, code
optimization, unused symbols removal, and unused feature removal in
Exynos thermal driver. Thanks Lukasz for this effort.
- Exynos thermal driver support to OF thermal. After the code
refactoring, the driver earned the support to OF thermal. Chip
thermal data were moved from driver code to DTS, reducing the code
footprint. Thanks Lukasz for this.
- After receiving the OF thermal support, the exynos thermal driver
now must allow modular build. Thanks Arnd for detecting, reporting
and fixing this.
- Exynos thermal driver support to Exynos 7 SoC. Thanks Abhilash for
this.
- Accurate temperature reporting on Rockchip thermal driver, thanks
to Caesar.
- Fix on how OF thermal enables its zones, thanks Lukasz for fixing.
- Fixes in OF thermal examples under Documentation/. Thanks Srinivas
for fixing"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
thermal: exynos: Add TMU support for Exynos7 SoC
dts: Documentation: Add documentation for Exynos7 SoC thermal bindings
cpufreq: exynos: allow modular build
thermal: Fix examples in DT documentation
thermal: exynos: Correct sanity check at exynos_report_trigger() function
thermal: Kconfig: Remove config for not used EXYNOS_THERMAL_CORE
thermal: exynos: Remove exynos_tmu_data.c file
thermal: rockchip: make temperature reporting much more accurate
thermal: exynos: Remove exynos_thermal_common.[c|h] files
thermal: samsung: core: Exynos TMU rework to use device tree for configuration
dts: Documentation: Update exynos-thermal.txt example for Exynos5440
dts: Documentation: Extending documentation entry for exynos-thermal
cpufreq: exynos: Use device tree to determine if cpufreq cooling should be registered
thermal: exynos: Modify exynos thermal code to use device tree for cpu cooling configuration
thermal: exynos: Provide thermal_exynos.h file to be included in device tree files
thermal: exynos: cosmetic: Correct comment format
thermal: of: Enable thermal_zoneX when sensor is correctly added
These are changes for drivers that are intimately tied to some SoC
and for some reason could not get merged through the respective
subsystem maintainer tree.
This time around, much of this is for at91, with the bulk of it being syscon
and udc drivers.
Also, there's:
- coupled cpuidle support for Samsung Exynos4210
- Renesas 73A0 common-clk work
- of/platform changes to tear down DMA mappings on device destruction
- a few updates to the TI Keystone knav code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJU4upSAAoJEIwa5zzehBx3HkUP/Rc4B1yZChNIFNfVq4dbei6w
dT9WdFmxOIj2JLeXEypFBiNf1nSHmsxrZe9/IDACz2fYQOnaZZ6/786utUJP/PtC
2GDJy9cjL2Xh03We3nQp5z6J33XvpEni1t82cOpCl8wLBOQNnkjEks8UvLgi1LHW
CNLcMm8JtDQ2aB/gRTjzetp9liZluESY5+Mig+loE2F/rzbMbNQDcWDDgUPyIQIS
1onL+Bad3BnGFdo/+qnkurGc81pxoKiQJty06VWFftzvIwxXhsNjrqls2+KzstAx
0lLvW1tqaDhXvUBImRM8GgfbldZslsgoFVmgESS9MpPMBNENYrkAiQNvJUnM7kd9
qHDQNq+zRNsz/k4fVvp/YUp7xEiAo4rLcFmp/dBr535jS2LNyiZnB94q+kXsin/m
tiyEMx+RWxEHTEHN9WdKE61Ty1RbzOa5UTLSzOKFAkF+m2nvuQsJvb97n19coAq9
SSsj/wJgesfqrDEegphCDh1fyVxUzlAjjhTAyvPS155WvPzkbxZxuBbSqRuriRKA
2aCfVne2ELimHAr3LEPgPW2kFBcONHckOGe6MvrTX4zPHU8bb9WIeg+iGdQChnr3
nclT9jq+ZnQro5XTgUtPtadq100oEXlJbqpAzhd+cJbvgzSNbcWfcgE6kOWqd9uK
oeWQWFLCdXLmXf9zCwmk
=T7R2
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"These are changes for drivers that are intimately tied to some SoC and
for some reason could not get merged through the respective subsystem
maintainer tree.
This time around, much of this is for at91, with the bulk of it being
syscon and udc drivers.
Also, there's:
- coupled cpuidle support for Samsung Exynos4210
- Renesas 73A0 common-clk work
- of/platform changes to tear down DMA mappings on device destruction
- a few updates to the TI Keystone knav code"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (26 commits)
cpuidle: exynos: add coupled cpuidle support for exynos4210
ARM: EXYNOS: apply S5P_CENTRAL_SEQ_OPTION fix only when necessary
soc: ti: knav_qmss_queue: change knav_range_setup_acc_irq to static
soc: ti: knav_qmss_queue: makefile tweak to build as dynamic module
pcmcia: at91_cf: depend on !ARCH_MULTIPLATFORM
soc: ti: knav_qmss_queue: export API calls for use by user driver
of/platform: teardown DMA mappings on device destruction
usb: gadget: at91_udc: Allocate udc instance
usb: gadget: at91_udc: Update DT binding documentation
usb: gadget: at91_udc: Rework for multi-platform kernel support
usb: gadget: at91_udc: Simplify probe and remove functions
usb: gadget: at91_udc: Remove non-DT handling code
usb: gadget: at91_udc: Document DT clocks and clock-names property
usb: gadget: at91_udc: Drop uclk clock
usb: gadget: at91_udc: Fix clock names
mfd: syscon: Add Atmel SMC binding doc
mfd: syscon: Add atmel-smc registers definition
mfd: syscon: Add Atmel Matrix bus DT binding documentation
mfd: syscon: Add atmel-matrix registers definition
clk: shmobile: fix sparse NULL pointer warning
...
DT changes continue to be the bulk of our merge window contents.
We continue to have a large set of changes across the board as new platforms
and drivers are added.
Some of the new platforms are:
- Alphascale ASM9260
- Marvell Armada 388
- CSR Atlas7
- TI Davinci DM816x
- Hisilicon HiP01
- ST STiH418
There have also been some sweeping changes, including relicensing of DTS
contents from GPL to GPLv2+/X11 so that the same files can be reused in
other non-GPL projects more easily. There's also been changes to the
DT Makefile to make it a little less conflict-ridden and churny down
the road.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XEw1
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"DT changes continue to be the bulk of our merge window contents.
We continue to have a large set of changes across the board as new
platforms and drivers are added.
Some of the new platforms are:
- Alphascale ASM9260
- Marvell Armada 388
- CSR Atlas7
- TI Davinci DM816x
- Hisilicon HiP01
- ST STiH418
There have also been some sweeping changes, including relicensing of
DTS contents from GPL to GPLv2+/X11 so that the same files can be
reused in other non-GPL projects more easily. There's also been
changes to the DT Makefile to make it a little less conflict-ridden
and churny down the road"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (330 commits)
ARM: dts: Add PPMU node for exynos4412-trats2
ARM: dts: Add PPMU node for exynos3250-monk and exynos3250-rinato
ARM: dts: Add PPMU dt node for exynos4 and exynos4210
ARM: dts: Add PPMU dt node for exynos3250
ARM: dts: add mipi dsi device node for exynos4415
ARM: dts: add fimd device node for exynos4415
ARM: dts: Add syscon phandle to the video-phy node for Exynos4
ARM: dts: Add sound nodes for exynos4412-trats2
ARM: dts: Fix CLK_MOUT_CAMn parent clocks assignment for exynos4412-trats2
ARM: dts: Fix CLK_UART_ISP_SCLK clock assignment in exynos4x12.dtsi
ARM: dts: Add max77693 charger node for exynos4412-trats2
ARM: dts: Switch max77686 regulators to GPIO control for exynos4412-trats2
ARM: dts: Add suspend configuration for max77686 regulators for exynos4412-trats2
ARM: dts: Add Maxim 77693 fuel gauge node for exynos4412-trats2
ARM: dts: am57xx-beagle-x15: Fix USB2 mode
ARM: dts: am57xx-beagle-x15: Add extcon nodes for USB
ARM: dts: dra72-evm: Add extcon nodes for USB
ARM: dts: dra7-evm: Add extcon nodes for USB
ARM: dts: rockchip: move the hdmi ddc-i2c-bus property to the actual boards
ARM: dts: rockchip: enable vops and hdmi output on rk3288-firefly and -evb
...
New and updated SoC support. Also included are some cleanups where the
platform maintainers hadn't separated cleanups from new developent in
separate branches.
Some of the larger things worth pointing out:
- A large set of changes from Alexandre Belloni and Nicolas Ferre
preparing at91 platforms for multiplatform and cleaning up quite a
bit in the process.
- Removal of CSR's "Marco" SoC platform that never made it out to the
market. We love seeing these since it means the vendor published
support before product was out, which is exactly what we want!
New platforms this release are:
- Conexant Digicolor (CX92755 SoC)
- Hisilicon HiP01 SoC
- CSR/sirf Atlas7 SoC
- ST STiH418 SoC
- Common code changes for Nvidia Tegra132 (64-bit SoC)
We're seeing more and more platforms having a harder time labelling
changes as cleanups vs new development -- which is a good sign that
we've come quite far on the cleanup effort. So over time we might start
combining the cleanup and new-development branches more.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=szd9
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"New and updated SoC support. Also included are some cleanups where
the platform maintainers hadn't separated cleanups from new developent
in separate branches.
Some of the larger things worth pointing out:
- A large set of changes from Alexandre Belloni and Nicolas Ferre
preparing at91 platforms for multiplatform and cleaning up quite a
bit in the process.
- Removal of CSR's "Marco" SoC platform that never made it out to the
market. We love seeing these since it means the vendor published
support before product was out, which is exactly what we want!
New platforms this release are:
- Conexant Digicolor (CX92755 SoC)
- Hisilicon HiP01 SoC
- CSR/sirf Atlas7 SoC
- ST STiH418 SoC
- Common code changes for Nvidia Tegra132 (64-bit SoC)
We're seeing more and more platforms having a harder time labelling
changes as cleanups vs new development -- which is a good sign that
we've come quite far on the cleanup effort. So over time we might
start combining the cleanup and new-development branches more"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (124 commits)
ARM: at91/trivial: unify functions and machine names
ARM: at91: remove at91_dt_initialize and machine init_early()
ARM: at91: change board files into SoC files
ARM: at91: remove at91_boot_soc
ARM: at91: move alternative initial mapping to board-dt-sama5.c
ARM: at91: merge all SOC_AT91SAM9xxx
ARM: at91: at91rm9200: set idle and restart from rm9200_dt_device_init()
ARM: digicolor: select syscon and timer
ARM: zynq: Simplify SLCR initialization
ARM: zynq: PM: Fixed simple typo.
ARM: zynq: Setup default gpio number for Xilinx Zynq
ARM: digicolor: add low level debug support
ARM: initial support for Conexant Digicolor CX92755 SoC
ARM: OMAP2+: Add dm816x hwmod support
ARM: OMAP2+: Add clock domain support for dm816x
ARM: OMAP2+: Add board-generic.c entry for ti81xx
ARM: at91: pm: remove warning to remove SOC_AT91SAM9263 usage
ARM: at91: remove unused mach/system_rev.h
ARM: at91: stop using HAVE_AT91_DBGUx
ARM: at91: fix ordering of SRAM and PM initialization
...
Here's the big staging driver tree update for 3.20-rc1. Lots of little
things in here, adding up to lots of overall cleanups. The IIO driver
updates are also in here as they cross the staging tree boundry a lot.
I2O has moved into staging as well, as a plan to drop it from the tree
eventually as that's a dead subsystem.
All of this has been in linux-next with no reported issues for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlTgtVQACgkQMUfUDdst+yk4mACgshYZ1fOQDoPR+BXd+QD1HXfh
GosAoICXkSjDQjwVo13W6QHIVMsUezY+
=4jHr
-----END PGP SIGNATURE-----
Merge tag 'staging-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging drivers patches from Greg KH:
"Here's the big staging driver tree update for 3.20-rc1.
Lots of little things in here, adding up to lots of overall cleanups.
The IIO driver updates are also in here as they cross the staging tree
boundry a lot. I2O has moved into staging as well, as a plan to drop
it from the tree eventually as that's a dead subsystem.
All of this has been in linux-next with no reported issues for a
while"
* tag 'staging-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (740 commits)
staging: lustre: lustre: libcfs: define symbols as static
staging: rtl8712: Do coding style cleanup
staging: lustre: make obd_updatemax_lock static
staging: rtl8188eu: core: switch with redundant cases
staging: rtl8188eu: odm: conditional setting with no effect
staging: rtl8188eu: odm: condition with no effect
staging: ft1000: fix braces warning
staging: sm7xxfb: fix remaining CamelCase
staging: sm7xxfb: fix CamelCase
staging: rtl8723au: multiple condition with no effect - if identical to else
staging: sm7xxfb: make smtc_scr_info static
staging/lustre/mdc: Initialize req in mdc_enqueue for !it case
staging/lustre/clio: Do not allow group locks with gid 0
staging/lustre/llite: don't add to page cache upon failure
staging/lustre/llite: Add exception entry check after radix_tree
staging/lustre/libcfs: protect kkuc_groups from write access
staging/lustre/fld: refer to MDT0 for fld lookup in some cases
staging/lustre/llite: Solve a race to access lli_has_smd in read case
staging/lustre/ptlrpc: hold rq_lock when modify rq_flags
staging/lustre/lnet: portal spreading rotor should be unsigned
...
- Framework changes and enhancements:
- Passing -DDEBUG recursively to subdir drivers so we get
debug messages properly turned on.
- Infer map type from DT property in the groups parsing code
in the generic pinconfig code.
- Support for custom parameter passing in generic pin config.
This is used when you are using the generic pin config, but
want to add a few custom properties that no other driver
will use.
- New drivers:
- Driver for the Xilinx Zynq
- Driver for the AmLogic Meson SoCs
- New features in drivers:
- Sleep support (suspend/resume) for the Cherryview driver
- mvebeu a38x can now mux a UART on pins MPP19 and MPP20
- Migrated the qualcomm driver to generic pin config handling
of extended config options in the core code.
- Support BUS1 and AUDIO in the Exynos pin controller.
- Add some missing functions in the sun6i driver.
- Add support for the A31S variant in the sun6i driver.
- EMEv2 support in the Renesas PFC driver.
- Ass support for Qualcomm MSM8916 in the qcom driver.
- Deleted features
- Drop support for the SiRF Marco that was never released to
the market.
- Drop SH7372 support as the support for this platform is
removed from the kernel.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Nbzh
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v3.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pincontrol updates from Linus Walleij:
:This is the bulk of pin control changes for the v3.20 cycle:
Framework changes and enhancements:
- Passing -DDEBUG recursively to subdir drivers so we get debug
messages properly turned on.
- Infer map type from DT property in the groups parsing code in the
generic pinconfig code.
- Support for custom parameter passing in generic pin config. This
is used when you are using the generic pin config, but want to add
a few custom properties that no other driver will use.
New drivers:
- Driver for the Xilinx Zynq
- Driver for the AmLogic Meson SoCs
New features in drivers:
- Sleep support (suspend/resume) for the Cherryview driver
- mvebeu a38x can now mux a UART on pins MPP19 and MPP20
- Migrated the qualcomm driver to generic pin config handling of
extended config options in the core code.
- Support BUS1 and AUDIO in the Exynos pin controller.
- Add some missing functions in the sun6i driver.
- Add support for the A31S variant in the sun6i driver.
- EMEv2 support in the Renesas PFC driver.
- Add support for Qualcomm MSM8916 in the qcom driver.
Deleted features
- Drop support for the SiRF Marco that was never released to the
market.
- Drop SH7372 support as the support for this platform is removed
from the kernel"
* tag 'pinctrl-v3.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (40 commits)
sh-pfc: emev2 - Fix mangled author name
pinctrl: cherryview: Configure HiZ pins to be input when requested as GPIOs
pinctrl: imx25: fix numbering for pins
pinctrl: pinctrl-imx: don't use invalid value of conf_reg
pinctrl: qcom: delete pin_config_get/set pinconf operations
pinctrl: qcom: Add msm8916 pinctrl driver
DT: pinctrl: Document Qualcomm MSM8916 pinctrl binding
pinctrl: qcom: increase variable size for register offsets
pinctrl: hide PCONFDUMP in #ifdef
pinctrl: rockchip: Only mask interrupts; never disable
pinctrl: zynq: Fix usb0 pins
pinctrl: sh-pfc: sh7372: Remove DT binding documentation
pinctrl: sh-pfc: sh7372: Remove PFC support
sh-pfc: Add emev2 pinmux support
sh-pfc: add macro to define pinmux without function
pinctrl: add driver for Amlogic Meson SoCs
staging: drivers: pinctrl: Fixed checkpatch.pl warnings
pinctrl: exynos: Add AUDIO pin controller for exynos7
sh-pfc: r8a7790: add MLB+ pin group
sh-pfc: r8a7791: add MLB+ pin group
...
In this batch, you can find lots of cleanups through the whole
subsystem, as our good New Year's resolution. Lots of LOCs and
commits are about LINE6 driver that was promoted finally from staging
tree, and as usual, there've been widely spread ASoC changes.
Here some highlights:
ALSA core changes
- Embedding struct device into ALSA core structures
- sequencer core cleanups / fixes
- PCM msbits constraints cleanups / fixes
- New SNDRV_PCM_TRIGGER_DRAIN command
- PCM kerneldoc fixes, header cleanups
- PCM code cleanups using more standard codes
- Control notification ID fixes
Driver cleanups
- Cleanups of PCI PM callbacks
- Timer helper usages cleanups
- Simplification (e.g. argument reduction) of many driver codes
HD-audio
- Hotkey and LED support on HP laptops with Realtek codecs
- Dock station support on HP laptops
- Toshiba Satellite S50D fixup
- Enhanced wallclock timestamp handling for HD-audio
- Componentization to simplify the linkage between i915 and hd-audio
drivers for Intel HDMI/DP
USB-audio
- Akai MPC Element support
- Enhanced timestamp handling
ASoC
- Lots of refactoringin ASoC core, moving drivers to more data
driven initialization and rationalizing a lot of DAPM usage
- Much improved handling of CDCLK clocks on Samsung I2S controllers
- Lots of driver specific cleanups and feature improvements
- CODEC support for TI PCM514x and TLV320AIC3104 devices
- Board support for Tegra systems with Realtek RT5677
- New driver for Maxim max98357a
- More enhancements / fixes for Intel SST driver
Others
- Promotion of LINE6 driver from staging along with lots of rewrites
and cleanups
- DT support for old non-ASoC atmel driver
- oxygen cleanups, XIO2001 init, Studio Evolution SE6x support
- Emu8000 DRAM size detection fix on ISA(!!) AWE64 boards
- A few more ak411x fixes for ice1724 boards
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=/84r
-----END PGP SIGNATURE-----
Merge tag 'sound-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"In this batch, you can find lots of cleanups through the whole
subsystem, as our good New Year's resolution. Lots of LOCs and
commits are about LINE6 driver that was promoted finally from staging
tree, and as usual, there've been widely spread ASoC changes.
Here some highlights:
ALSA core changes
- Embedding struct device into ALSA core structures
- sequencer core cleanups / fixes
- PCM msbits constraints cleanups / fixes
- New SNDRV_PCM_TRIGGER_DRAIN command
- PCM kerneldoc fixes, header cleanups
- PCM code cleanups using more standard codes
- Control notification ID fixes
Driver cleanups
- Cleanups of PCI PM callbacks
- Timer helper usages cleanups
- Simplification (e.g. argument reduction) of many driver codes
HD-audio
- Hotkey and LED support on HP laptops with Realtek codecs
- Dock station support on HP laptops
- Toshiba Satellite S50D fixup
- Enhanced wallclock timestamp handling for HD-audio
- Componentization to simplify the linkage between i915 and hd-audio
drivers for Intel HDMI/DP
USB-audio
- Akai MPC Element support
- Enhanced timestamp handling
ASoC
- Lots of refactoringin ASoC core, moving drivers to more data driven
initialization and rationalizing a lot of DAPM usage
- Much improved handling of CDCLK clocks on Samsung I2S controllers
- Lots of driver specific cleanups and feature improvements
- CODEC support for TI PCM514x and TLV320AIC3104 devices
- Board support for Tegra systems with Realtek RT5677
- New driver for Maxim max98357a
- More enhancements / fixes for Intel SST driver
Others
- Promotion of LINE6 driver from staging along with lots of rewrites
and cleanups
- DT support for old non-ASoC atmel driver
- oxygen cleanups, XIO2001 init, Studio Evolution SE6x support
- Emu8000 DRAM size detection fix on ISA(!!) AWE64 boards
- A few more ak411x fixes for ice1724 boards"
* tag 'sound-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (542 commits)
ALSA: line6: toneport: Use explicit type for firmware version
ALSA: line6: Use explicit type for serial number
ALSA: line6: Return EIO if read/write not successful
ALSA: line6: Return error if device not responding
ALSA: line6: Add delay before reading status
ASoC: Intel: Clean data after SST fw fetch
ALSA: hda - Add docking station support for another HP machine
ALSA: control: fix failure to return new numerical ID in 'replace' event data
ALSA: usb: update trigger timestamp on first non-zero URB submitted
ALSA: hda: read trigger_timestamp immediately after starting DMA
ALSA: pcm: allow for trigger_tstamp snapshot in .trigger
ALSA: pcm: don't override timestamp unconditionally
ALSA: off by one bug in snd_riptide_joystick_probe()
ASoC: rt5670: Set use_single_rw flag for regmap
ASoC: rt286: Add rt288 codec support
ASoC: max98357a: Fix build in !CONFIG_OF case
ASoC: Intel: fix platform_no_drv_owner.cocci warnings
ARM: dts: Switch Odroid X2/U2 to simple-audio-card
ARM: dts: Exynos4 and Odroid X2/U3 sound device nodes update
ALSA: control: fix failure to return numerical ID in 'add' event
...
variant of the rk3288-evb and the setting of a clock for the watchdog.
Also the lcd and hdmi controllers on both the firefly and the evb get
enabled and let us now boot into fbcon console sucessfully.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJUy+f+AAoJEPOmecmc0R2BdFcH/i+9hgt9ElJxKbpPPVPVv81O
QzmIi3g+B4WqAoKBfzkug5l82mSZ4FAvmQK5ad8BYHsBaGl+GRjwwaqRqZkPUOzl
umXk0GneZ5sPK+S1UdA/S/v7hTwgEpXOLnGUCGUXbLt7Gqda99ume08jgCe2JbH5
Tfjoia5uRlOgdZIf3KBr4TkPR+LHog1i/DI9N3XrAsjLtj/igHpoRmFydBmv7noo
OuRuPY0afg1jKs/MextjM0W1JzQbGyv4Jp4NjVFv60+KZrMgS64vTDZamxYEK4Sv
wn0pQUZgevQhd3ewdLtqrcbo4wIGiLWBXQK0vzonmo5tCk8r+59QFKxeMiq2C7Q=
=ZVrD
-----END PGP SIGNATURE-----
Merge tag 'v3.20-rockchip-dts3' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Merge "ARM: rockchip: third (and last) batch of dts updates for 3.20" from
Heiko Stübner:
Change are regulator nodes for the cpu and gpu regulators on the act8846
variant of the rk3288-evb and the setting of a clock for the watchdog.
Also the lcd and hdmi controllers on both the firefly and the evb get
enabled and let us now boot into fbcon console sucessfully.
* tag 'v3.20-rockchip-dts3' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: move the hdmi ddc-i2c-bus property to the actual boards
ARM: dts: rockchip: enable vops and hdmi output on rk3288-firefly and -evb
ARM: dts: rockchip: housekeeping off i2c0 on rk3288-evb boards
ARM: dts: rockchip: add cpu and gpu regulators to rk3288-evb-act8846
ARM: dts: rockchip: add rk3288 watchdog clock
clk: rockchip: add id for watchdog pclk on rk3288
clk: rockchip: add clock IDs for the PVTM clocks
clk: rockchip: add clock ID for usbphy480m_src
Signed-off-by: Olof Johansson <olof@lixom.net>
and addition of clock definitions for DVFS on Exynos4.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=rFdT
-----END PGP SIGNATURE-----
Merge tag 'v3.20-exynos-clk' of git://linuxtv.org/snawrocki/samsung into clk-next
Exynos 3250, 4415 drivers cleanup by using common code
and addition of clock definitions for DVFS on Exynos4.
PLLD is the only parent for DSIA & DSIB on Tegra124 and
Tegra132. Besides, BIT 30 in PLLD_MISC register controls
the output of DSI clock.
So this patch removes "dsia_mux" & "dsib_mux", and create
a new clock "plld_dsi" to represent the DSI clock enable
control.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Mark Zhang <markz@nvidia.com>
Split the Tegra124 clock macros into two files:
1. Clock macros common to both Tegra124 and Tegra132
2. Clock macros specific to Tegra124
This was requested by Thierry in Message-ID
<20140716072539.GD7978@ulmo>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <pwalmsley@nvidia.com>
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
- add DISP1 power domain for support HDMI support on exynos5420/5422/5800
and the power domain node including FIMD1, MIXER and HDMI modules
(tested on exynos5420 Peach Pit and exynos5800 Peach Pi Chromebooks
and exynos5422 Odroid XU3 by Javier Martinez Canillas)
Note this is including a patch for adding clock IDs for the DISP1 power
domain with Mike and Sylwester's acks so that could be handled together
to avoid non-working.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=9Imn
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
Merge "Samsung 3rd DT updates for v3.20" from Kukjin Kim:
- add DISP1 power domain for support HDMI support on exynos5420/5422/5800
and the power domain node including FIMD1, MIXER and HDMI modules
(tested on exynos5420 Peach Pit and exynos5800 Peach Pi Chromebooks
and exynos5422 Odroid XU3 by Javier Martinez Canillas)
Note this is including a patch for adding clock IDs for the DISP1 power
domain with Mike and Sylwester's acks so that could be handled together
to avoid non-working.
* tag 'samsung-dt-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Add DISP1 power domain for exynos5420
clk: exynos5420: Add IDs for clocks used in DISP1 power domain
Signed-off-by: Olof Johansson <olof@lixom.net>
When a power domain is powered off on Exynos5420 SoC, the input clocks of
the devices attached to this power domain are re-parented to oscclk and
restored to the original parent after powering on the power domain.
So a reference to the input and parent clocks for the devices attached to
a power domain are needed to be able to do the re-parenting. The DISP1 pd
includes modules which uses the following clocks:
ACLK_200_DISP1 (MIXER and HDMILINK)
ACLK_300_DISP1 (FIMD1)
ACLK_400_DISP1 (Internal Buses)
Each of these clocks are generated as the output of a clock mux so add an
ID for all of these clock muxes and their parents to be referenced in the
DISP1 power domain device node.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Document DT binding for Qualcomm SPMI PMIC voltage ADC
driver.
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds the divider clock id for Exynos4 memory bus frequency.
The clock id is used for DVFS (Dynamic Voltage/Frequency Scaling)
feature of the exynos memory bus.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Conflicts:
arch/arm/boot/dts/imx6sx-sdb.dts
net/sched/cls_bpf.c
Two simple sets of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
we currently only "fake" as the clock gate control is living in a
very strange place, but the watchdog driver needs to read the clock
rate from it and the setting of rk3288 plls to slow mode upon suspend.
Other than that some more exported clocks and a CLK_SET_RATE_PARENT
flag for the uart clocks.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJUwT2NAAoJEPOmecmc0R2BjmsH/1Mp2vS9E9RBREhL/uuwtVlE
6FhINcpzVkDrwXGfupVbrWmzHTxKcyUbnluVPsLs0BCRqhhKSU0t+TT5j+mRMOpu
oNq/d3cp//fuBaiLr4G0jrgd/a9Gq4SsshPP6kH41r5CBN87jTt9wazX2GjNBf4C
LYsNNWj/qpXxeA/rFuMsI15ntPiFvap8Ag/5+IDCHuT9nwCLy7iI3G0MRGZ1kfGT
byOJd/FOqfAk3UJXuEgGOu27ZAOcbGLk7EL7YUdq7C70wAlUTu/8smTLqJFbXc9T
Xgum3FnYcuPZqNQSxQMXFpgyzE0q7KLyufv5gU1A4s2Ac69cD3nDVh9k1LAcu4s=
=arKA
-----END PGP SIGNATURE-----
Merge tag 'v3.20-rockchip-clk1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into clk-next
The two big changes are the additional of the watchdog clock, which
we currently only "fake" as the clock gate control is living in a
very strange place, but the watchdog driver needs to read the clock
rate from it and the setting of rk3288 plls to slow mode upon suspend.
Other than that some more exported clocks and a CLK_SET_RATE_PARENT
flag for the uart clocks.
Add an LCC driver for MSM8960/APQ8064 that supports the i2s,
slimbus, and pcm clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Add defines to make more human readable numbers for the lpass
clock controller found on IPQ806x SoCs. Also remove the PLL4
define in gcc to avoid #define conflicts because that clock
doesn't exist in gcc, instead it lives in lcc.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
[sboyd@codeaurora.org: Split off into separate patch]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
A lot of changes to the device tree for the 3.20 merge window, mostly with:
- More DT license convertions, only two DTS and two DTSI are still uncertain
and have not been converted yet
- Use the C-preprocessor includes in the device trees.
- Add support for the A31s SoC and improve the A80 support
- Add IR receiver, lradc, PS/2 support
- Add cpufreq support for all SoCs but the A23 and A80.
- And a lot of new boards
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=pWBS
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-3.20' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Merge "Allwinner device tree changes for 3.20" from Maxime Ripard:
A lot of changes to the device tree for the 3.20 merge window, mostly with:
- More DT license convertions, only two DTS and two DTSI are still uncertain
and have not been converted yet
- Use the C-preprocessor includes in the device trees.
- Add support for the A31s SoC and improve the A80 support
- Add IR receiver, lradc, PS/2 support
- Add cpufreq support for all SoCs but the A23 and A80.
- And a lot of new boards
* tag 'sunxi-dt-for-3.20' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (64 commits)
ARM: dts: sun5i: Enable axp209 support on A13-OLinuxIno
ARM: sunxi: dts: Add A10/A20 PS2 pin muxing options
ARM: sunxi: dts: Add PS2 nodes to dtsi for A10,A20
ARM: dts: sun6i: Add resistive touchscreen controller node to dtsi
ARM: dts: sun4i: Add Hyundau A7HD board
ARM: dts: sun4i: Add Marsboard A10 board
ARM: dts: sun9i: Enable mmc2 on A80 Optimus Board
ARM: dts: sun9i: Add 8 bit mmc pinmux setting for mmc2
ARM: dts: sun9i: Enable mmc0 on A80 Optimus Board
ARM: dts: sun9i: Convert a80 optimus board dts to label referencing
ARM: dts: sun9i: Add mmc controller nodes to the A80 dtsi
ARM: dts: sun9i: Add mmc config clock nodes
ARM: dts: sunxi: Add missing mdio label
ARM: dts: sun5i: Add mk802_a10s board
ARM: dts: sun4i: Add mk802ii board
ARM: dts: sun4i: Add mk802 board
ARM: dts: sun4i: Add dts file for Chuwi V7 CW0825 tablet
ARM: dts: sun7i: Add dts file for Bananapro board
ARM: sun6i: Enable ARM arch timers
ARM: dts: sun6i: Convert hummingbird a31 dts to label references
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This is a driver for the pinmux and GPIO controller available in
Amlogic Meson SoCs. It currently supports only Meson8, however the
common code should be generic enough to work also for other SoCs after
having defined the proper set of functions and groups.
GPIO interrupts are not supported at the moment due to lack of
documentation.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch is a preparatory patch to be able to read Exynos thermal
configuration from the device tree.
It turned out that DTC is not able to interpret enums properly and hence
it is necessary to #define those values explicitly.
For this reason the ./include/dt-bindings/thermal/thermal_exynos.h file
has been introduced.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
- Update i.MX6 operating-points setting in device tree to match the
latest i.MX6 data sheet
- Add i.MX6SX sabreauto board support
- Add imx6dl-udoo board support based off imx6q-udoo
- Update sabrelite board to include I2C and HDMI support
- Update the VPU compatible strings to also use cnm,coda<model>
- Remove the ocram clock from the VPU node, as the clock is already
provided inside the ocram node
- Add system reset controller and syscon-reboot for VF610
- Update VF610 device tree to use zero based naming for GPIO nodes,
so that the number scheme matches hardware manual
- A number of random device additions like watchdog for VF610, sahara
for i.MX53, QSPI for imx6sx-sdb board, etc.
Note: the branch imx/soc was merged into imx/dt because the SNVS device
tree node needs to refer to the new clock ID added by the imx/soc patch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUwg4gAAoJEFBXWFqHsHzO1NIH/AlXPcZZQM8sYbHrvWXmvVTM
JstCR6XjVvOqT9zdFbEzdgpFGvu1oSDer8tOk00hL1NZYzHJRmTr/wgNP6tsvQ0F
uoRj62B+WaMMcFanTbSdzh0tJtp7HZyFkJwjWRIL76bmd4VBsHXCPw4tr3oeDLzm
x62SP14eSevV8ydlZj4TA2Ej7SxV6esdPLGeylZldXKTvo8AUH9sYN/BAz7WXfYH
wfQ8owW/ql7YyCSRVdhSoeGG4H9qJA9M/CdwofsorLONkUx0nrBPRQfku5Uvf8Op
fydbEbZ0LAkqIVnHcLi8xgBDhjjS/7glHSx4tp+mxtDcIMzAzfAtjyrawheWqQE=
=ni1W
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
Merge "ARM: imx: device tree changes for 3.20" from Shawn Guo:
The i.MX device tree update for 3.20:
- Update i.MX6 operating-points setting in device tree to match the
latest i.MX6 data sheet
- Add i.MX6SX sabreauto board support
- Add imx6dl-udoo board support based off imx6q-udoo
- Update sabrelite board to include I2C and HDMI support
- Update the VPU compatible strings to also use cnm,coda<model>
- Remove the ocram clock from the VPU node, as the clock is already
provided inside the ocram node
- Add system reset controller and syscon-reboot for VF610
- Update VF610 device tree to use zero based naming for GPIO nodes,
so that the number scheme matches hardware manual
- A number of random device additions like watchdog for VF610, sahara
for i.MX53, QSPI for imx6sx-sdb board, etc.
Note: the branch imx/soc was merged into imx/dt because the SNVS device
tree node needs to refer to the new clock ID added by the imx/soc patch.
* tag 'imx-dt-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (28 commits)
ARM: dts: imx28-evk: remove duplicate property
ARM: vf610: use zero based naming for GPIO nodes
ARM: dts: imx6q: enable dma for ecspi5
ARM: dts: vfxxx: Add SNVS node
ARM: imx: clk-vf610: Add clock for SNVS
ARM: imx: clk-vf610: Add clock for UART4 and UART5
ARM: imx: drop CPUIDLE_FLAG_TIME_VALID from cpuidle-imx6sx
ARM: dts: imx6dl-udoo: Add board support based off imx6q-udoo
ARM: imx: support arm power off in cpuidle for i.mx6sx
ARM: imx: remove unnecessary setting for DSM
ARM: dts: imx6sx: add i.mx6sx sabreauto board support
ARM: dts: imx6sx-sdb: Add QSPI support
ARM: dts: imx6qdl: Remove OCRAM clock from VPU node
ARM: imx: apf51dev: add gpio-backlight support
ARM: imx: correct the hardware clock gate setting for shared nodes
ARM: imx: pllv3: add shift for frequency multiplier
ARM vf610: add compatibilty strings of supported Vybrid SoC's
ARM: i.MX53: dts: add sahara module
ARM: dts: imx6dl: correct cpufreq volt/freq table
ARM: dts: imx6q: update cpufreq volt/freq table
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- Add .disable_unused function hook for shared gate clock to ensure
the clock tree use count matches the hardware state
- Add a deeper idle state for i.MX6SX cpuidle driver powering off the
ARM core
- One correction on i.MX6Q esai_ipg parent clock setting
- Add a missing iounmap call for imx6q_opp_check_speed_grading()
- Add missing clocks for VF610 UART4, UART5 and SNVS blocks
- Expand VF610 device tree compatible matching table to cover more
Vybrid family SoCs
- Expand i.MX clk-pllv3 a bit with the shift for frequency multiplier
to support Vybrid's USB PLL oddity
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUwgT5AAoJEFBXWFqHsHzO2fAIAKnvpNONYdZFI0Q1Z5sIl+/8
Sl+Cs+dCfG5ZHKcqOQ/1ir1OpCEvZW6QQfnK7j1MKpDCIStnmBXRg723H4bh0Kbx
7/uB0nF3wrBuMweEoqGsx4fOfKDLgHUzMt+3jNOubiDoQcQIZmxPECsPifj9aVSV
Z+TkHoslKv4XAKRzuOX2aepLwv1a6OJ3As9gaKVbzF8QVb2JGgvuKafruREfV0dP
R7XWEscS1vd1xMEKiCMtJcnQ8nKaaToB8oRhk8VvpvgVIReC96PeAbrA7melVEjR
paqlnp1qZlf+M03rebvmrHVLFT6OWRTULJ3jh1D8U8AJaNnAw8u1W1k6cIeWMos=
=Vsin
-----END PGP SIGNATURE-----
Merge tag 'imx-soc-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/soc
Merge "ARM: imx: soc changes for 3.20" from Shawn Guo:
The i.MX SoC changes for 3.20:
- Add .disable_unused function hook for shared gate clock to ensure
the clock tree use count matches the hardware state
- Add a deeper idle state for i.MX6SX cpuidle driver powering off the
ARM core
- One correction on i.MX6Q esai_ipg parent clock setting
- Add a missing iounmap call for imx6q_opp_check_speed_grading()
- Add missing clocks for VF610 UART4, UART5 and SNVS blocks
- Expand VF610 device tree compatible matching table to cover more
Vybrid family SoCs
- Expand i.MX clk-pllv3 a bit with the shift for frequency multiplier
to support Vybrid's USB PLL oddity
* tag 'imx-soc-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: clk-imx6q: refine esai_ipg's parent
ARM i.MX6q: unmap memory mapped at imx6q_opp_check_speed_grading()
ARM: imx: clk-vf610: Add clock for SNVS
ARM: imx: clk-vf610: Add clock for UART4 and UART5
ARM: imx: drop CPUIDLE_FLAG_TIME_VALID from cpuidle-imx6sx
ARM: imx: support arm power off in cpuidle for i.mx6sx
ARM: imx: remove unnecessary setting for DSM
ARM: imx: correct the hardware clock gate setting for shared nodes
ARM: imx: pllv3: add shift for frequency multiplier
ARM vf610: add compatibilty strings of supported Vybrid SoC's
Signed-off-by: Olof Johansson <olof@lixom.net>
dm816x devices and clocks. Also adds a qspi device for
dra72x-evm.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=vWKv
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.20/dt-pt2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Merge "omap device tree changes for v3.20, part 2" from Tony Lindgren:
More changes for omap dts files mostly to add support for
dm816x devices and clocks. Also adds a qspi device for
dra72x-evm.
* tag 'omap-for-v3.20/dt-pt2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: dra72-evm: Add qspi device
ARM: dts: Add minimal support for dm8168-evm
ARM: dts: Add basic clocks for dm816x
ARM: dts: Add basic dm816x device tree configuration
Signed-off-by: Olof Johansson <olof@lixom.net>
Add binding for the Qualcomm Resource Power Manager (RPM) found in 8660,
8960 and 8064 based devices.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Adds a new id for the pclk supplying the watchdog on rk3288 socs.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
The pinctrl nodes require some extra opaque arguments for the pull up and drive
strength values.
Introduce a new header file and convert the device trees to replace these
opaque numbers by defines.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The DMA engine for the A10/A20 and derivatives require an opaque extra
argument.
Add a dt-bindings header, and convert the device trees to it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Provide CLK support for Alphascale ASM9260 SoC.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
This allows booting the device with basic functionality.
Note that at least on my revision c board the DDR3 does
not seem to work properly and only some of the memory
can be reliably used.
Also, the mainline u-boot does not seem to properly
initialize the ethernet, so I've been using the old TI
u-boot at:
http://arago-project.org/git/projects/?p=u-boot-omap3.git;a=summary
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The STiH418 is advanced UHD 60fps AVC processor with 3D graphic acceleration and
quad-core ARM Cortex A9 CPU.
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Add support for PDMA0 and PDMA1 gate clks.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
The new DT properties required for the I2S device node to be referred
as a clock provider and corresponding clock indices definition is added.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for clock gating of the SNVS peripheral.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
* Use clock-indices instead of deprecated renesas,clock-indices
* Prepare for r8a73a4 multiplatform support
* Increase clock coverage for r8a779[014]
* Correct r8a7779 clock usage
* Correct LAN9220 VDDVARIO voltage on ape6evm
* Correct QSPI SPI-Flash mode of lager and koelsch
* Correct flash partition label and size on koelsch
* Correct mask for GIC PPI interrupts on r8a779[14]
* Correct BSC bus range on ape6evm-reference
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=fZ4r
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-for-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Merge "Renesas ARM Based SoC DT Updates for v3.20" from Simon Horman:
* Use clock-indices instead of deprecated renesas,clock-indices
* Prepare for r8a73a4 multiplatform support
* Increase clock coverage for r8a779[014]
* Correct r8a7779 clock usage
* Correct LAN9220 VDDVARIO voltage on ape6evm
* Correct QSPI SPI-Flash mode of lager and koelsch
* Correct flash partition label and size on koelsch
* Correct mask for GIC PPI interrupts on r8a779[14]
* Correct BSC bus range on ape6evm-reference
* tag 'renesas-dt-for-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (30 commits)
ARM: shmobile: r8a7791: add MLB+ clock
ARM: shmobile: r8a7790: add MLB+ clock
ARM: shmobile: ape6evm: Fix LAN9220 VDDVARIO voltage
ARM: shmobile: r8a73a4: Add r8a73a4-ape6evm.dtb to ARCH_SHMOBILE_MULTI
ARM: shmobile: ape6evm: Add keypad to the device tree
ARM: shmobile: ape6evm: Add LEDs to the device tree
ARM: shmobile: ape6evm: synchronize dts with reference platform
ARM: shmobile: ape6evm: fix compatible string for Ethernet controller
ARM: shmobile: r8a7794: Add MMCIF clock to device tree
ARM: shmobile: r8a7794: Add SDHI clocks to device tree
ARM: shmobile: r8a7794: Add I2C clocks to device tree
ARM: shmobile: r8a7779: Add TWD device to DTS
ARM: shmobile: r8a7779: Use MSTP for SCIF clocks
ARM: shmobile: r8a7779: Use R8A7779_CLK_P as SCIF parent clock
ARM: shmobile: r8a7794: Add QSPI clock to device tree
ARM: shmobile: lager: Fix QSPI mode of SPI-Flash into mode3
ARM: shmobile: r8a7794: Add SYS-DMAC clocks to device tree
ARM: shmobile: r8a7791: Add IPMMU-SGX clock to device tree
ARM: shmobile: koelsch: Fix QSPI mode of SPI-Flash into mode3
ARM: shmobile: r8a7794: Add USBDMAC[01] clocks to device tree
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Dave Gerlach