Spectrum-2 supports an ACL action SIP_DIP, which allows IPv4 and IPv6
source and destination addresses change. Offload suitable mangles to
the IPv6 address change action.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spectrum-2 supports an ACL action SIP_DIP, which allows IPv4 and IPv6
source and destination addresses change. Offload suitable mangles to
the IPv4 address change action.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add fields related to SIP_DIP_ACTION, which is used for changing of SIP
and DIP addresses.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Menglong Dong says:
====================
net: use kfree_skb_reason() for ip/udp packet receive
In this series patches, kfree_skb() is replaced with kfree_skb_reason()
during ipv4 and udp4 packet receiving path, and following drop reasons
are introduced:
SKB_DROP_REASON_SOCKET_FILTER
SKB_DROP_REASON_NETFILTER_DROP
SKB_DROP_REASON_OTHERHOST
SKB_DROP_REASON_IP_CSUM
SKB_DROP_REASON_IP_INHDR
SKB_DROP_REASON_IP_RPFILTER
SKB_DROP_REASON_UNICAST_IN_L2_MULTICAST
SKB_DROP_REASON_XFRM_POLICY
SKB_DROP_REASON_IP_NOPROTO
SKB_DROP_REASON_SOCKET_RCVBUFF
SKB_DROP_REASON_PROTO_MEM
TCP is more complex, so I left it in the next series.
I just figure out how __print_symbolic() works. It doesn't base on the
array index, but searching for symbols by loop. So I'm a little afraid
it's performance.
Changes since v3:
- fix some small problems in the third patch (net: ipv4: use
kfree_skb_reason() in ip_rcv_core()), as David Ahern said
Changes since v2:
- use SKB_DROP_REASON_PKT_TOO_SMALL for a path in ip_rcv_core()
Changes since v1:
- add document for all drop reasons, as David advised
- remove unreleated cleanup
- remove EARLY_DEMUX and IP_ROUTE_INPUT drop reason
- replace {UDP, TCP}_FILTER with SOCKET_FILTER
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace kfree_skb() with kfree_skb_reason() in __udp_queue_rcv_skb().
Following new drop reasons are introduced:
SKB_DROP_REASON_SOCKET_RCVBUFF
SKB_DROP_REASON_PROTO_MEM
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace kfree_skb() with kfree_skb_reason() in udp_queue_rcv_one_skb().
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace kfree_skb() with kfree_skb_reason() in ip_protocol_deliver_rcu().
Following new drop reasons are introduced:
SKB_DROP_REASON_XFRM_POLICY
SKB_DROP_REASON_IP_NOPROTO
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace kfree_skb() with kfree_skb_reason() in ip_rcv_finish_core(),
following drop reasons are introduced:
SKB_DROP_REASON_IP_RPFILTER
SKB_DROP_REASON_UNICAST_IN_L2_MULTICAST
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace kfree_skb() with kfree_skb_reason() in ip_rcv_core(). Three new
drop reasons are introduced:
SKB_DROP_REASON_OTHERHOST
SKB_DROP_REASON_IP_CSUM
SKB_DROP_REASON_IP_INHDR
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace kfree_skb() with kfree_skb_reason() in nf_hook_slow() when
skb is dropped by reason of NF_DROP. Following new drop reasons
are introduced:
SKB_DROP_REASON_NETFILTER_DROP
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add document for following existing drop reasons:
SKB_DROP_REASON_NOT_SPECIFIED
SKB_DROP_REASON_NO_SOCKET
SKB_DROP_REASON_PKT_TOO_SMALL
SKB_DROP_REASON_TCP_CSUM
SKB_DROP_REASON_SOCKET_FILTER
SKB_DROP_REASON_UDP_CSUM
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit e940066089 ("lib/stackdepot: always do filter_irq_stacks()
in stack_depot_save()") it became unnecessary to filter the stack
before calling stack_depot_save().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Marco Elver <elver@google.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While testing a patch that will follow later
("net: add netns refcount tracker to struct nsproxy")
I found that devtmpfs_init() was called before init_net
was initialized.
This is a bug, because devtmpfs_setup() calls
ksys_unshare(CLONE_NEWNS);
This has the effect of increasing init_net refcount,
which will be later overwritten to 1, as part of setup_net(&init_net)
We had too many prior patches [1] trying to work around the root cause.
Really, make sure init_net is in BSS section, and that net_ns_init()
is called earlier at boot time.
Note that another patch ("vfs: add netns refcount tracker
to struct fs_context") also will need net_ns_init() being called
before vfs_caches_init()
As a bonus, this patch saves around 4KB in .data section.
[1]
f8c46cb390 ("netns: do not call pernet ops for not yet set up init_net namespace")
b5082df801 ("net: Initialise init_net.count to 1")
734b65417b ("net: Statically initialize init_net.dev_base_head")
v2: fixed a build error reported by kernel build bots (CONFIG_NET=n)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, HSR manages mac addresses of known HSR nodes by using list_head.
It takes a lot of time when there are a lot of registered nodes due to
finding specific mac address nodes by using linear search. We can be
reducing the time by using hlist. Thus, this patch moves list_head to
hlist_head for mac addresses and this allows for further improvement of
network performance.
Condition: registered 10,000 known HSR nodes
Before:
# iperf3 -c 192.168.10.1 -i 1 -t 10
Connecting to host 192.168.10.1, port 5201
[ 5] local 192.168.10.2 port 59442 connected to 192.168.10.1 port 5201
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.49 sec 3.75 MBytes 21.1 Mbits/sec 0 158 KBytes
[ 5] 1.49-2.05 sec 1.25 MBytes 18.7 Mbits/sec 0 166 KBytes
[ 5] 2.05-3.06 sec 2.44 MBytes 20.3 Mbits/sec 56 16.9 KBytes
[ 5] 3.06-4.08 sec 1.43 MBytes 11.7 Mbits/sec 11 38.0 KBytes
[ 5] 4.08-5.00 sec 951 KBytes 8.49 Mbits/sec 0 56.3 KBytes
After:
# iperf3 -c 192.168.10.1 -i 1 -t 10
Connecting to host 192.168.10.1, port 5201
[ 5] local 192.168.10.2 port 36460 connected to 192.168.10.1 port 5201
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.00 sec 7.39 MBytes 62.0 Mbits/sec 3 130 KBytes
[ 5] 1.00-2.00 sec 5.06 MBytes 42.4 Mbits/sec 16 113 KBytes
[ 5] 2.00-3.00 sec 8.58 MBytes 72.0 Mbits/sec 42 94.3 KBytes
[ 5] 3.00-4.00 sec 7.44 MBytes 62.4 Mbits/sec 2 131 KBytes
[ 5] 4.00-5.07 sec 8.13 MBytes 63.5 Mbits/sec 38 92.9 KBytes
Signed-off-by: Juhee Kang <claudiajkang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have plans for increasing MAX_SKB_FRAGS, but sk_msg_sg::copy
is currently an unsigned long, limiting MAX_SKB_FRAGS to 30 on 32bit arches.
Convert it to a bitmap, as Jakub suggested.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of disabling TSO at compile time if MAX_SKB_FRAGS > 32,
implement ndo_features_check() method for this driver for
a more dynamic handling.
If skb has more than 32 frags and is a GSO packet, force
software segmentation.
Most locally generated packets will use a small number
of fragments anyway.
For forwarding workloads, we can limit gro_max_size at ingress,
we might also implement gro_max_segs if needed.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems this one-element array is not actually being used as an
array of variable size, so we can just replace it with just a
non-array object of type struct desc_frag and refactor a bit the
rest of the code.
This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
This issue was found with the help of Coccinelle and audited and fixed,
manually.
[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/v5.16/process/deprecated.html#zero-length-and-one-element-arrays
Link: https://github.com/KSPP/linux/issues/79
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a regular need in the kernel to provide a way to declare having
a dynamically sized set of trailing elements in a structure. Kernel code
should always use “flexible array members”[1] for these cases. The older
style of one-element or zero-length arrays should no longer be used[2].
This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
This issue was found with the help of Coccinelle and audited and fixed,
manually.
[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/v5.16/process/deprecated.html#zero-length-and-one-element-arrays
Link: https://github.com/KSPP/linux/issues/79
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Haiyang Zhang says:
====================
net: mana: Add handling of CQE_RX_TRUNCATED and a cleanup
Add handling of CQE_RX_TRUNCATED and a cleanup patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch statement already ensures cqe_type == CQE_RX_OKAY at that
point.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The proper way to drop this kind of CQE is advancing rxq tail
without indicating the packet to the upper network layer.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet says:
====================
net: device tracking improvements
Main goal of this series is to be able to detect the following case
which apparently is still haunting us.
dev_hold_track(dev, tracker_1, GFP_ATOMIC);
dev_hold(dev);
dev_put(dev);
dev_put(dev); // Should complain loudly here.
dev_put_track(dev, tracker_1); // instead of here (as before this series)
v2: third patch:
I replaced the dev_put() in linkwatch_do_dev() with __dev_put().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We are still chasing some syzbot reports where we think a rogue dev_put()
is called with no corresponding prior dev_hold().
Unfortunately it eats a reference on dev->dev_refcnt taken by innocent
dev_hold_track(), meaning that the refcount saturation splat comes
too late to be useful.
Make sure that 'not tracked' dev_put() and dev_hold() better use
CONFIG_NET_DEV_REFCNT_TRACKER=y debug infrastructure:
Prior patch in the series allowed ref_tracker_alloc() and ref_tracker_free()
to be called with a NULL @trackerp parameter, and to use a separate refcount
only to detect too many put() even in the following case:
dev_hold_track(dev, tracker_1, GFP_ATOMIC);
dev_hold(dev);
dev_put(dev);
dev_put(dev); // Should complain loudly here.
dev_put_track(dev, tracker_1); // instead of here
Add clarification about netdev_tracker_alloc() role.
v2: I replaced the dev_put() in linkwatch_do_dev()
with __dev_put() because callers called netdev_tracker_free().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are still chasing a netdev refcount imbalance, and we suspect
we have one rogue dev_put() that is consuming a reference taken
from a dev_hold_track()
To detect this case, allow ref_tracker_alloc() and ref_tracker_free()
to be called with a NULL @trackerp parameter, and use a dedicated
refcount_t just for them.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever ref_tracker_dir_init() is called, mark the struct ref_tracker_dir
as dead.
Test the dead status from ref_tracker_alloc() and ref_tracker_free()
This should detect buggy dev_put()/dev_hold() happening too late
in netdevice dismantle process.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet says:
====================
ipv6: mc_forwarding changes
First patch removes minor data-races, as mc_forwarding can
be locklessly read in fast path.
Second patch adds a short cut in ip6mr_sk_done()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In many cases, ip6mr_sk_done() is called while no ipmr socket
has been registered.
This removes 4 rtnl acquisitions per netns dismantle,
with following callers:
igmp6_net_exit(), tcpv6_net_exit(), ndisc_net_exit()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes minor data-races in ip6_mc_input() and
batadv_mcast_mla_rtr_flags_softif_get_ipv6()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We generally default the vendor to y and the drivers itself
to n. NET_DSA_REALTEK, however, selects a whole bunch of things,
so it's not a pure "vendor selection" knob. Let's default it all
to n.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Phylink will use PCS polling whenever phylink_config.pcs_poll or the
phylink_pcs poll member is set. As this driver sets both, remove the
former.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
phylink_set_10g_modes() is no longer used with the conversion of
drivers to phylink_generic_validate(), so we can remove it.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni says:
====================
gro: a couple of minor optimization
This series collects a couple of small optimizations for the GRO engine,
reducing slightly the number of cycles for dev_gro_receive().
The delta is within noise range in tput tests, but with big TCP coming
every cycle saved from the GRO engine will count - I hope ;)
v1 -> v2:
- a few cleanup suggested from Alexander(s)
- moved away the more controversial 3rd patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
While inspecting some perf report, I noticed that the compiler
emits suboptimal code for the napi CB initialization, fetching
and storing multiple times the memory for flags bitfield.
This is with gcc 10.3.1, but I observed the same with older compiler
versions.
We can help the compiler to do a nicer work clearing several
fields at once using an u32 alias. The generated code is quite
smaller, with the same number of conditional.
Before:
objdump -t net/core/gro.o | grep " F .text"
0000000000000bb0 l F .text 0000000000000357 dev_gro_receive
After:
0000000000000bb0 l F .text 000000000000033c dev_gro_receive
v1 -> v2:
- use struct_group (Alexander and Alex)
RFC -> v1:
- use __struct_group to delimit the zeroed area (Alexander)
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 5e10da5385 ("skbuff: allow 'slow_gro' for skb
carring sock reference") and commit af352460b4 ("net: fix GRO
skb truesize update") the truesize of the skb with stolen head is
properly updated by the GRO engine, we don't need anymore resetting
it at recycle time.
v1 -> v2:
- clarify the commit message (Alexander)
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a copy and paste bug. It was supposed to check "clear_skb"
instead of "write_skb".
Fixes: 2cd5485663 ("net: dsa: qca8k: add support for phy read/write with mgmt Ethernet")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Horatiu Vultur says:
====================
net: lan966x: add support for mcast snooping
Implement the switchdev callback SWITCHDEV_ATTR_ID_BRIDGE_MC_DISABLED
to allow to enable/disable multicast snooping.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When the multicast snooping is disabled, the mdb entries should be
removed from the HW, but they still need to be kept in memory for when
the mcast_snooping will be enabled again.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The callback allows to enable/disable multicast snooping.
When the snooping is enabled, all IGMP and MLD frames are redirected to
the CPU, therefore make sure not to set the skb flag 'offload_fwd_mark'.
The HW will not flood multicast ipv4/ipv6 data frames.
When the snooping is disabled, the HW will flood IGMP, MLD and multicast
ipv4/ipv6 frames according to the mcast_flood flag.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When enabling the multicast snooping, the forwarding of the IPV6 frames
has it's own forwarding mask.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently tc skb extension is used to send miss info from
tc to ovs datapath module, and driver to tc. For the tc to ovs
miss it is currently always allocated even if it will not
be used by ovs datapath (as it depends on a requested feature).
Export the static key which is used by openvswitch module to
guard this code path as well, so it will be skipped if ovs
datapath doesn't need it. Enable this code path once
ovs datapath needs it.
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mat Martineau says:
====================
mptcp: Improve set-flags command and update self tests
Patches 1-3 allow more flexibility in the combinations of features and
flags allowed with the MPTCP_PM_CMD_SET_FLAGS netlink command, and add
self test case coverage for the new functionality.
Patches 4-6 and 9 refactor the mptcp_join.sh self tests to allow them to
configure all of the test cases using either the pm_nl_ctl utility (part
of the mptcp self tests) or the 'ip mptcp' command (from iproute2). The
default remains to use pm_nl_ctl.
Patches 7 and 8 update the pm_netlink.sh self tests to cover the use of
endpoint ids to set endpoint flags (instead of just addresses).
====================
Link: https://lore.kernel.org/r/20220205000337.187292-1-mathew.j.martineau@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch added a command line option '-i' for mptcp_join.sh to use
'ip mptcp' commands instead of using 'pm_nl_ctl' commands to deal with
PM netlink.
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch added the setting flags test cases, using both addr-based and
id-based lookups for the setting address.
The output looks like this:
set flags (backup) [ OK ]
(nobackup) [ OK ]
(fullmesh) [ OK ]
(nofullmesh) [ OK ]
(backup,fullmesh) [ OK ]
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch added the id argument for setting the address flags in
pm_nl_ctl.
Usage:
pm_nl_ctl set id 1 flags backup
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch implemented a new function named pm_nl_set_endpoint(), wrapped
the PM netlink commands 'ip mptcp endpoint change flags' and 'pm_nl_ctl
set flags' in it, and used a new argument 'ip_mptcp' to choose which one
to use to set the flags of the PM endpoint.
'ip mptcp' used the ID number argument to find out the address to change
flags, while 'pm_nl_ctl' used the address and port number arguments. So
we need to parse the address ID from the PM dump output as well as the
address and port number.
Used this wrapper in do_transfer() instead of using the pm_nl_ctl command
directly.
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch implemented a new function named pm_nl_show_endpoints(), wrapped
the PM netlink commands 'ip mptcp endpoint show' and 'pm_nl_ctl dump' in
it, used a new argument 'ip_mptcp' to choose which one to use to show all
the PM endpoints.
Used this wrapper in do_transfer() instead of using the pm_nl_ctl commands
directly.
The original 'pos+=5' in the remoing tests only works for the output of
'pm_nl_ctl show':
id 1 flags subflow 10.0.1.1
It doesn't work for the output of 'ip mptcp endpoint show':
10.0.1.1 id 1 subflow
So implemented a more flexible approach to get the address ID from the PM
dump output to fit for both commands.
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch added four basic 'ip mptcp' wrappers:
pm_nl_set_limits()
pm_nl_add_endpoint()
pm_nl_del_endpoint()
pm_nl_flush_endpoint().
Wrapped the PM netlink commands 'ip mptcp' and 'pm_nl_ctl' in them, and
used a new argument 'ip_mptcp' to choose which one to use for setting the
PM limits, adding or deleting the PM endpoint.
Used the wrappers in all the selftests in mptcp_join.sh instead of using
the pm_nl_ctl commands directly.
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch added the backup testcase using an address with a port number.
The original backup tests only work for the output of 'pm_nl_ctl dump'
without the port number. It chooses the last item in the dump to parse
the address in it, and in this case, the address is showed at the end
of the item.
But it doesn't work for the dump with the port number, in this case, the
port number is showed at the end of the item, not the address.
So implemented a more flexible approach to get the address and the port
number from the dump to fit for the port number case.
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch added the port argument for setting the address flags in
pm_nl_ctl.
Usage:
pm_nl_ctl set 10.0.2.1 flags backup port 10100
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It's illegal to use both port and non-signal flags for adding address.
But it's legal to use both of them for setting flags, which always uses
non-signal flags, backup or fullmesh.
This patch moves this non-signal flag with port check from
mptcp_pm_parse_addr() to mptcp_nl_cmd_add_addr(). Do the check only when
adding addresses, not setting flags or deleting addresses.
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Danielle Ratson