If the driver reports that the hardware had an overflow, report this to
userspace. It would be nice to know when this happens, and not just get
a long space.
This change has been tested with lircd, ir-ctl, and ir-keytable.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
These features have never been implemented by any lirc driver, including
staging or out of tree drivers. The ioctls for these feaures were removed
in commit d55f09abe2 ("[media] lirc.h: remove several unused ioctls").
So, we can safely remove them.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This packed grey-scale image format has a depth of 10 bits per pixel.
Every four consecutive pixels are packed into 5 bytes. Each of the first
4 bytes contain the 8 high order bits of the pixels, and the 5th byte
contains the 2 least significants bits of each pixel, in the same order.
The first two bytes are not corresponding to this description, fix it.
Fixes: af4f450576 ("media: doc: pixfmt-yuv: Move all luma-only YUV formats to common file")
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Example should be comparing errno to EINTR instead of doing assignment.
Signed-off-by: Daniel Lundberg Pedersen <dlp@qtec.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Reference Picture Set lists provide indices of short and long term
reference in DBP array.
Fix Hantro to not do a look up in DBP entries.
Make documentation more clear about it.
[hverkuil: fix typo in commit log]
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Marking a picture as long-term reference is valid for DPB but not for RPS.
Change flag name to match with the description in HEVC spec chapter
"8.3.2 Decoding process for reference picture set".
PocStCurrBefore, PocStCurrAfter, PocLtCurr lists could be built by the
kernel from the DPB entries struct v4l2_hevc_dpb_entry, using the
information in the rps field. This way RPS flags becomes useless and are
removed.
This patch breaks the staging HEVC API because it introduces a new flag,
changes a field name in v4l2_hevc_dpb_entry structure and removes
V4L2_HEVC_DPB_ENTRY_RPS_* flags.
[hverkuil: fixed some typos]
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The specification for VIDIOC_DQBUF is slightly ambiguous on what fields
of |struct v4l2_buffer| is filled by the driver.
Reword it so things are clear: the driver fills in all remaining fields
not specified to be filled in by userspace applications.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Merge support for the Platform Firmware Runtime Update and Telemetry
interface based on ACPI.
The interface provided here allows updating certain pieces of the
platform firmware without restarting the system and collecting
platform firmware telemetry data.
This also includes a utility for accesing the new interface from user
space.
* acpi-pfrut:
ACPI: pfr_telemetry: Fix info leak in pfrt_log_ioctl()
ACPI: pfr_update: Fix return value check in pfru_write()
ACPI: tools: Introduce utility for firmware updates/telemetry
ACPI: Introduce Platform Firmware Runtime Telemetry driver
ACPI: Introduce Platform Firmware Runtime Update device driver
efi: Introduce EFI_FIRMWARE_MANAGEMENT_CAPSULE_HEADER and corresponding structures
Introduce the pfr_update driver which can be used for Platform Firmware
Runtime code injection and driver update [1].
The user is expected to provide the EFI capsule, and pass it to the
driver by writing the capsule to a device special file. The capsule
is transferred by the driver to the platform firmware with the help
of an ACPI _DSM method under the special ACPI Platform Firmware
Runtime Update device (INTC1080), and the actual firmware update is
carried out by the low-level Management Mode code in the platform
firmware.
This change allows certain pieces of the platform firmware to be
updated on the fly while the system is running (runtime) without the
need to restart it, which is key in the cases when the system needs to
be available 100% of the time and it cannot afford the downtime related
to restarting it, or when the work carried out by the system is
particularly important, so it cannot be interrupted, and it is not
practical to wait until it is complete.
Link: https://uefi.org/sites/default/files/resources/Intel_MM_OS_Interface_Spec_Rev100.pdf # [1]
Tested-by: Hongyu Ning <hongyu.ning@intel.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Without timeout reports, it is impossible to decode many protocols since
it is not known when the transmission ends. timeout reports are sent by
default, but can be turned off. There is no reason to turn them off, and
I cannot find any software which does this, so we can safely remove it.
This makes the ioctl LIRC_SET_REC_TIMEOUT_REPORTS a no-op.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The beginning part of the "existing HSV/HSL formats" table (line 7742)
reads:
.. raw:: latex
\begingroup
\tiny
\setlength{\tabcolsep}{2pt}
However, the ending part (line 7834) reads:
.. raw:: latex
\normalsize
Fix the imbalance by replacing the \normalsize with \endgroup.
Note:
Actually, the imbalance is harmless and just results in an
informative message near the bottom of userspace-api.log:
(\end occurred inside a group at level 1)
### semi simple group (level 1) entered at line 70696 (\begingroup)
### bottom level
Link: https://lore.kernel.org/linux-media/b3eeec4d-1a34-0a1a-3097-1ddea3b5f1c8@gmail.com
Signed-off-by: Akira Yokosawa <akiyks@gmail.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
V4L2_PIX_FMT_HM12 was redefined to V4L2_PIX_FMT_NV12_16L16, so use the
new name in libv4l-introduction.rst.
This fixes this warning:
libv4l-introduction.rst:27: WARNING: undefined label: v4l2-pix-fmt-hm12
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
CAPTURE buffers might be read by the hardware after they are dequeued,
which goes against the general idea that userspace has full control over
dequeued buffers. Explain why and document the restrictions that this
implies for userspace.
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Acked-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add the VP9 stateless decoder controls plus the documentation that goes
with it.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Co-developed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Adrian Ratiu <adrian.ratiu@collabora.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Co-developed-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Improve the documentation for CEC_RECEIVE/TRANSMIT w.r.t. the
sequence and tx/rx_status fields.
Also remove a duplicate tx_status description.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix example code which has missing or double backslash typo.
Signed-off-by: Kwang Son <dev.kwang.son@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add V4L2_COLORFX_SET_RGB color effects control, V4L2_CID_COLORFX_RGB
for RGB color setting.
with two mirror changes:
- change 0xFFFFFF to 0xffffff
- fix comments 2^24 to 2^24 - 1
[hverkuil: dropped spaces around + with V4L2_CID_BASE for consistency]
Signed-off-by: Dillon Min <dillon.minfei@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Here is the big set of char and misc and other tiny driver subsystem
updates for 5.16-rc1.
Loads of things in here, all of which have been in linux-next for a
while with no reported problems (except for one called out below.)
Included are:
- habanana labs driver updates, including dma_buf usage,
reviewed and acked by the dma_buf maintainers
- iio driver update (going through this tree not staging as they
really do not belong going through that tree anymore)
- counter driver updates
- hwmon driver updates that the counter drivers needed, acked by
the hwmon maintainer
- xillybus driver updates
- binder driver updates
- extcon driver updates
- dma_buf module namespaces added (will cause a build error in
arm64 for allmodconfig, but that change is on its way through
the drm tree)
- lkdtm driver updates
- pvpanic driver updates
- phy driver updates
- virt acrn and nitr_enclaves driver updates
- smaller char and misc driver updates
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYYPX2A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymUUgCbB4EKysgLuXYdjUalZDx+vvZO4k0AniS14O4k
F+2dVSZ5WX6wumUzCaA6
=bXQM
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of char and misc and other tiny driver subsystem
updates for 5.16-rc1.
Loads of things in here, all of which have been in linux-next for a
while with no reported problems (except for one called out below.)
Included are:
- habanana labs driver updates, including dma_buf usage, reviewed and
acked by the dma_buf maintainers
- iio driver update (going through this tree not staging as they
really do not belong going through that tree anymore)
- counter driver updates
- hwmon driver updates that the counter drivers needed, acked by the
hwmon maintainer
- xillybus driver updates
- binder driver updates
- extcon driver updates
- dma_buf module namespaces added (will cause a build error in arm64
for allmodconfig, but that change is on its way through the drm
tree)
- lkdtm driver updates
- pvpanic driver updates
- phy driver updates
- virt acrn and nitr_enclaves driver updates
- smaller char and misc driver updates"
* tag 'char-misc-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (386 commits)
comedi: dt9812: fix DMA buffers on stack
comedi: ni_usb6501: fix NULL-deref in command paths
arm64: errata: Enable TRBE workaround for write to out-of-range address
arm64: errata: Enable workaround for TRBE overwrite in FILL mode
coresight: trbe: Work around write to out of range
coresight: trbe: Make sure we have enough space
coresight: trbe: Add a helper to determine the minimum buffer size
coresight: trbe: Workaround TRBE errata overwrite in FILL mode
coresight: trbe: Add infrastructure for Errata handling
coresight: trbe: Allow driver to choose a different alignment
coresight: trbe: Decouple buffer base from the hardware base
coresight: trbe: Add a helper to pad a given buffer area
coresight: trbe: Add a helper to calculate the trace generated
coresight: trbe: Defer the probe on offline CPUs
coresight: trbe: Fix incorrect access of the sink specific data
coresight: etm4x: Add ETM PID for Kryo-5XX
coresight: trbe: Prohibit trace before disabling TRBE
coresight: trbe: End the AUX handle on truncation
coresight: trbe: Do not truncate buffer on IRQ
coresight: trbe: Fix handling of spurious interrupts
...
-----BEGIN PGP SIGNATURE-----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=eLup
-----END PGP SIGNATURE-----
Merge tag 'media/v5.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- New driver for SK Hynix Hi-846 8M pixel camera
- New driver for the ov13b10 camera
- New driver for Renesas R-Car ISP
- mtk-vcodec gained support for version 2 of decoder firmware ABI
- The legacy sir_ir driver got removed
- videobuf2: the vb2_mem_ops kAPI had some improvements
- lots of cleanups, fixes and new features at device drivers
* tag 'media/v5.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (328 commits)
media: venus: core: Add sdm660 DT compatible and resource struct
media: dt-bindings: media: venus: Add sdm660 dt schema
media: venus: vdec: decoded picture buffer handling during reconfig sequence
media: venus: Handle fatal errors during encoding and decoding
media: venus: helpers: Add helper to mark fatal vb2 error
media: venus: hfi: Check for sys error on session hfi functions
media: venus: Make sys_error flag an atomic bitops
media: venus: venc: Use pmruntime autosuspend
media: allegro: write vui parameters for HEVC
media: allegro: nal-hevc: implement generator for vui
media: allegro: write correct colorspace into SPS
media: allegro: extract nal value lookup functions to header
media: allegro: correctly scale the bit rate in SPS
media: allegro: remove external QP table
media: allegro: fix row and column in response message
media: allegro: add control to disable encoder buffer
media: allegro: add encoder buffer support
media: allegro: add pm_runtime support
media: allegro: lookup VCU settings
media: allegro: fix module removal if initialization failed
...
- Move futex code into kernel/futex/ and split up the kitchen sink into
seperate files to make integration of sys_futex_waitv() simpler.
- Add a new sys_futex_waitv() syscall which allows to wait on multiple
futexes. The main use case is emulating Windows' WaitForMultipleObjects
which allows Wine to improve the performance of Windows Games. Also
native Linux games can benefit from this interface as this is a common
wait pattern for this kind of applications.
- Add context to ww_mutex_trylock() to provide a path for i915 to rework
their eviction code step by step without making lockdep upset until the
final steps of rework are completed. It's also useful for regulator and
TTM to avoid dropping locks in the non contended path.
- Lockdep and might_sleep() cleanups and improvements
- A few improvements for the RT substitutions.
- The usual small improvements and cleanups.
-----BEGIN PGP SIGNATURE-----
iQJHBAABCgAxFiEEQp8+kY+LLUocC4bMphj1TA10mKEFAmF/FTITHHRnbHhAbGlu
dXRyb25peC5kZQAKCRCmGPVMDXSYoVNZD/9vIm3Bu1Coz8tbNXz58AiCYq9Y/vp5
mzFgSzz+VJTkW5Vh8jo5Uel4rCKZyt+rL276EoaRPzYl8KFtWDbpK3qd3PrXKqTX
At49JO4ttAMJUHIBQ6vblEkykmfEd9YPU1uSWk5roJ+s7Jmr5VWnu0FEWHP00As5
tWOca/TM0ei9kof26V2fl5aecTGII4i4Zsvy+LPsXtI+TnmP0gSBcGAS/5UnZTtJ
vQRWTR3ojoYvh5iTmNqbaURYoQLe2j8yscn1DSW1CABWVmP12eDWs+N7jRP4b5S9
73xOv5P7vpva41wxrK2ir5iNkpsLE97VL2JOHTW8nm7orblfiuxHLTCkTjEdd2pO
h8blI2IBizEB3JYn2BMkOAaZQOSjN8hd6Ye/b2B4AMEGWeXEoEv6eVy/orYKCluQ
XDqGn47Vce/SYmo5vfTB8VMt6nANx8PKvOP3IvjHInYEQBgiT6QrlUw3RRkXBp5s
clQkjYYwjAMVIXowcCrdhoKjMROzi6STShVwHwGL8MaZXqr8Vl6BUO9ckU0pY+4C
F000Hzwxi8lGEQ9k+P+BnYOEzH5osCty8lloKiQ/7ciX6T+CZHGJPGK/iY4YL8P5
C3CJWMsHCqST7DodNFJmdfZt99UfIMmEhshMDduU9AAH0tHCn8vOu0U6WvCtpyBp
BvHj68zteAtlYg==
=RZ4x
-----END PGP SIGNATURE-----
Merge tag 'locking-core-2021-10-31' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking updates from Thomas Gleixner:
- Move futex code into kernel/futex/ and split up the kitchen sink into
seperate files to make integration of sys_futex_waitv() simpler.
- Add a new sys_futex_waitv() syscall which allows to wait on multiple
futexes.
The main use case is emulating Windows' WaitForMultipleObjects which
allows Wine to improve the performance of Windows Games. Also native
Linux games can benefit from this interface as this is a common wait
pattern for this kind of applications.
- Add context to ww_mutex_trylock() to provide a path for i915 to
rework their eviction code step by step without making lockdep upset
until the final steps of rework are completed. It's also useful for
regulator and TTM to avoid dropping locks in the non contended path.
- Lockdep and might_sleep() cleanups and improvements
- A few improvements for the RT substitutions.
- The usual small improvements and cleanups.
* tag 'locking-core-2021-10-31' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (44 commits)
locking: Remove spin_lock_flags() etc
locking/rwsem: Fix comments about reader optimistic lock stealing conditions
locking: Remove rcu_read_{,un}lock() for preempt_{dis,en}able()
locking/rwsem: Disable preemption for spinning region
docs: futex: Fix kernel-doc references
futex: Fix PREEMPT_RT build
futex2: Documentation: Document sys_futex_waitv() uAPI
selftests: futex: Test sys_futex_waitv() wouldblock
selftests: futex: Test sys_futex_waitv() timeout
selftests: futex: Add sys_futex_waitv() test
futex,arm: Wire up sys_futex_waitv()
futex,x86: Wire up sys_futex_waitv()
futex: Implement sys_futex_waitv()
futex: Simplify double_lock_hb()
futex: Split out wait/wake
futex: Split out requeue
futex: Rename mark_wake_futex()
futex: Rename: match_futex()
futex: Rename: hb_waiter_{inc,dec,pending}()
futex: Split out PI futex
...
-----BEGIN PGP SIGNATURE-----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=NmI1
-----END PGP SIGNATURE-----
Merge tag 'for-5.16/cdrom-2021-10-29' of git://git.kernel.dk/linux-block
Pull CDROM updates from Jens Axboe:
"On behalf of Phillip, here are the CDROM updates for the 5.16-rc1
merge window:
- Add ioctl for improved media change detection (Lukas)
- Reformat some documentation (Phillip)
- Redundant variable removal (luo)"
* tag 'for-5.16/cdrom-2021-10-29' of git://git.kernel.dk/linux-block:
cdrom: Remove redundant variable and its assignment
cdrom: docs: reformat table in Documentation/userspace-api/ioctl/cdrom.rst
drivers/cdrom: improved ioctl for media change detection
Add PTP_CLK_MAGIC to the userspace-api/ioctl/ioctl-number.rst
documentation file.
Fixes: d94ba80ebb ("ptp: Added a brand new class driver for ptp clocks.")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/20211024163831.10200-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Most interesting element this time is the new chrdev based interface
for the counter subsystem. Affects all drivers. Some minor precursor
patches.
Major parts:
* Bring all the sysfs attribute setup into the counter core rather than
leaving it to individual drivers. Docs updates accompany these changes.
* Move various definitions to a uapi header as now needed from userspace.
* Add the chardev interface + extensive documentation and example tool
* Add new ABI needed to identify indexes needed for chrdev interface
* Implement new interface for the 104-quad-8
* Follow up deals with wrong path for documentation build
* Various trivial cleanups and missing feature additions related to this
series
-----BEGIN PGP SIGNATURE-----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=AaeD
-----END PGP SIGNATURE-----
Merge tag 'counter-for-5.16a-take2' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
First set of counter subsystem new feature support for the 5.16 cycle
Most interesting element this time is the new chrdev based interface
for the counter subsystem. Affects all drivers. Some minor precursor
patches.
Major parts:
* Bring all the sysfs attribute setup into the counter core rather than
leaving it to individual drivers. Docs updates accompany these changes.
* Move various definitions to a uapi header as now needed from userspace.
* Add the chardev interface + extensive documentation and example tool
* Add new ABI needed to identify indexes needed for chrdev interface
* Implement new interface for the 104-quad-8
* Follow up deals with wrong path for documentation build
* Various trivial cleanups and missing feature additions related to this
series
* tag 'counter-for-5.16a-take2' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
docs: counter: Include counter-chrdev kernel-doc to generic-counter.rst
counter: fix docum. build problems after filename change
counter: microchip-tcb-capture: Tidy up a false kernel-doc /** marking.
counter: 104-quad-8: Add IRQ support for the ACCES 104-QUAD-8
counter: 104-quad-8: Replace mutex with spinlock
counter: Implement events_queue_size sysfs attribute
counter: Implement *_component_id sysfs attributes
counter: Implement signalZ_action_component_id sysfs attribute
tools/counter: Create Counter tools
docs: counter: Document character device interface
counter: Add character device interface
counter: Move counter enums to uapi header
docs: counter: Update to reflect sysfs internalization
counter: Update counter.h comments to reflect sysfs internalization
counter: Internalize sysfs interface code
counter: stm32-timer-cnt: Provide defines for slave mode selection
counter: stm32-lptimer-cnt: Provide defines for clock polarities
Fix a VDUSE documentation build warning:
Documentation/userspace-api/vduse.rst:21: WARNING: Title underline too short.
Fixes: 7bc7f61897 ("Documentation: Add documentation for VDUSE")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Xie Yongji <xieyongji@bytedance.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: virtualization@lists.linux-foundation.org
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-doc@vger.kernel.org
Link: https://lore.kernel.org/r/20211006202904.30241-1-rdunlap@infradead.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Xie Yongji <xieyongji@bytedance.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Add extra space to the first column of ioctl values table, and also realign
the text in the second column, to fix a documentation build warning
introduced by: commit 67f1e027c2 ("drivers/cdrom: improved ioctl for
media change detection")
Suggested-by: Randy Dunlap <rdunlap@infradead.org>
Fixes: 67f1e027c2 ("drivers/cdrom: improved ioctl for media change detection")
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20211007231720.31997-1-phil@philpotter.co.uk
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch lets user-space request a non-coherent memory
allocation during CREATE_BUFS and REQBUFS ioctl calls.
= CREATE_BUFS
struct v4l2_create_buffers has seven 4-byte reserved areas,
so reserved[0] is renamed to ->flags. The struct, thus, now
has six reserved 4-byte regions.
= CREATE_BUFS32
struct v4l2_create_buffers32 has seven 4-byte reserved areas,
so reserved[0] is renamed to ->flags. The struct, thus, now
has six reserved 4-byte regions.
= REQBUFS
We use one byte of a 4 byte ->reserved[1] member of struct
v4l2_requestbuffers. The struct, thus, now has reserved 3 bytes.
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
By setting or clearing the V4L2_MEMORY_FLAG_NON_COHERENT flag
user-space should be able to hint vb2 that either non-coherent
(if supported) or coherent memory should be used for the buffer
allocation.
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The uvc driver relies on the camera firmware to keep the control states
and therefore is not capable of changing an inactive control.
Allow returning -EACCES in those cases.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add documentation for the V4L2_CID_NOTIFY_GAINS control.
This control is required by sensors that need to know what colour
gains will be applied to pixels by downstream processing (such as by
an ISP), though the sensor does not apply these gains itself.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add Mediatek's non-compressed 8 bit block video mode. This format is
produced by the MT8183 codec and can be converted to a non-proprietary
format by the MDP3 component.
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add more information about V4L2_PIX_FMT_NV12MT and
V4L2_PIX_FMT_NV12M_16X16, so it's clearer for driver authors and users.
Also, group the two pixel formats with the other tiled formats,
for clarity.
Unlike the recently introduced tiled formats (V4L2_PIX_FMT_NV12_4L4, etc)
these formats have remained Samsung-specific until now. Therefore, and
although the NV12MT and NV12MT_16X16 nomenclatures are less clear, we are
keeping them as-is.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This format is produced by VeriSilicon Hantro G2 and VC8000D cores.
It is a simple 4x4 tiling layout in a linear way.
The pixel format was introduced by GStreamer using FourCC VT12,
so let's stick to it.
Link: https://gstreamer.freedesktop.org/documentation/video/video-format.html
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The V4L2_PIX_FMT_HM12 format is actually a simple NV12 tiled format,
with 16x16 linear tiles. Rename the format and move its documentation
together with the other tiled NV12 formats.
Keep V4L2_PIX_FMT_HM12 for application compatibility.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The V4L2_PIX_FMT_SUNXI_TILED_NV12 format is actually a fairly
common NV12 tiled format, with 32x32 linear tiles. Rename the format
and move its documentation together with the other tiled NV12 formats.
Keep V4L2_PIX_FMT_SUNXI_TILED_NV12 for application compatibility.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
HEVC scaling lists are used for the scaling process for transform
coefficients.
V4L2_HEVC_SPS_FLAG_SCALING_LIST_ENABLED has to set when they are
encoded in the bitstream.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The current implementation of the CDROM_MEDIA_CHANGED ioctl relies on
global state, meaning that only one process can detect a disc change
while the ioctl call will return 0 for other calling processes afterwards
(see bug 213267).
This introduces a new cdrom ioctl, CDROM_TIMED_MEDIA_CHANGE, that
works by maintaining a timestamp of the last detected disc change instead
of a boolean flag: Processes calling this ioctl command can provide
a timestamp of the last disc change known to them and receive
an indication whether the disc was changed since then and the updated
timestamp.
I considered fixing the buggy behavior in the original
CDROM_MEDIA_CHANGED ioctl but that would require maintaining state
for each calling process in the kernel, which seems like a worse
solution than introducing this new ioctl.
Signed-off-by: Lukas Prediger <lumip@lumip.de>
Link: https://lore.kernel.org/all/20210912191207.74449-1-lumip@lumip.de
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Link: https://lore.kernel.org/r/20210913230942.1188-1-phil@philpotter.co.uk
Signed-off-by: Jens Axboe <axboe@kernel.dk>
vduse driver supporting blk
virtio-vsock support for end of record with SEQPACKET
vdpa: mac and mq support for ifcvf and mlx5
vdpa: management netlink for ifcvf
virtio-i2c, gpio dt bindings
misc fixes, cleanups
NB: when merging this with
b542e383d8 ("eventfd: Make signal recursion protection a task bit")
from Linus' tree, replace eventfd_signal_count with
eventfd_signal_allowed, and drop the export of eventfd_wake_count from
("eventfd: Export eventfd_wake_count to modules").
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmE1+awPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpt6EIAJy0qrc62lktNA0IiIVJSLbUbTMmFj8MzkGR
8UxZdhpjWqBPJPyaOuNeksAqTGm/UAPEYx3C2c95Jhej7anFpy7dbCtIXcPHLJME
DjcJg+EDrlNCj8m0FcsHpHWsFzPMERJpyEZNxgB5WazQbv+yWhGrg2FN5DCnF0Ro
ZFYeKSVty148pQ0nHl8X0JM2XMtqit+O+LvKN2HQZ+fubh7BCzMxzkHY0QLHIzUS
UeZqd3Qm8YcbqnlX38P5D6k+NPiTEgknmxaBLkPxg6H3XxDAmaIRFb8Ldd1rsgy1
zTLGDiSGpVDIpawRnuEAzqJThV3Y5/MVJ1WD+mDYQ96tmhfp+KY=
=DBH/
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio updates from Michael Tsirkin:
- vduse driver ("vDPA Device in Userspace") supporting emulated virtio
block devices
- virtio-vsock support for end of record with SEQPACKET
- vdpa: mac and mq support for ifcvf and mlx5
- vdpa: management netlink for ifcvf
- virtio-i2c, gpio dt bindings
- misc fixes and cleanups
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (39 commits)
Documentation: Add documentation for VDUSE
vduse: Introduce VDUSE - vDPA Device in Userspace
vduse: Implement an MMU-based software IOTLB
vdpa: Support transferring virtual addressing during DMA mapping
vdpa: factor out vhost_vdpa_pa_map() and vhost_vdpa_pa_unmap()
vdpa: Add an opaque pointer for vdpa_config_ops.dma_map()
vhost-iotlb: Add an opaque pointer for vhost IOTLB
vhost-vdpa: Handle the failure of vdpa_reset()
vdpa: Add reset callback in vdpa_config_ops
vdpa: Fix some coding style issues
file: Export receive_fd() to modules
eventfd: Export eventfd_wake_count to modules
iova: Export alloc_iova_fast() and free_iova_fast()
virtio-blk: remove unneeded "likely" statements
virtio-balloon: Use virtio_find_vqs() helper
vdpa: Make use of PFN_PHYS/PFN_UP/PFN_DOWN helper macro
vsock_test: update message bounds test for MSG_EOR
af_vsock: rename variables in receive loop
virtio/vsock: support MSG_EOR bit processing
vhost/vsock: support MSG_EOR bit processing
...
VDUSE (vDPA Device in Userspace) is a framework to support
implementing software-emulated vDPA devices in userspace. This
document is intended to clarify the VDUSE design and usage.
Signed-off-by: Xie Yongji <xieyongji@bytedance.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/r/20210831103634.33-14-xieyongji@bytedance.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This VDUSE driver enables implementing software-emulated vDPA
devices in userspace. The vDPA device is created by
ioctl(VDUSE_CREATE_DEV) on /dev/vduse/control. Then a char device
interface (/dev/vduse/$NAME) is exported to userspace for device
emulation.
In order to make the device emulation more secure, the device's
control path is handled in kernel. A message mechnism is introduced
to forward some dataplane related control messages to userspace.
And in the data path, the DMA buffer will be mapped into userspace
address space through different ways depending on the vDPA bus to
which the vDPA device is attached. In virtio-vdpa case, the MMU-based
software IOTLB is used to achieve that. And in vhost-vdpa case, the
DMA buffer is reside in a userspace memory region which can be shared
to the VDUSE userspace processs via transferring the shmfd.
For more details on VDUSE design and usage, please see the follow-on
Documentation commit.
NB(mst): when merging this with
b542e383d8 ("eventfd: Make signal recursion protection a task bit")
replace eventfd_signal_count with eventfd_signal_allowed,
and drop the previous
("eventfd: Export eventfd_wake_count to modules").
Signed-off-by: Xie Yongji <xieyongji@bytedance.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/r/20210831103634.33-13-xieyongji@bytedance.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----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=PQpb
-----END PGP SIGNATURE-----
Merge tag 'media/v5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new sensor drivers: imx335, imx412, ov9282
- new IR transmitter driver: meson-ir-tx
- handro driver gained support for H.264 for Rockchip VDPU2
- imx gained support for i.MX8MQ
- ti-vpe has gained support for other SoC variants
- lots of cleanups, fixes, board additions and doc improvements
* tag 'media/v5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (195 commits)
media: venus: venc: add support for V4L2_CID_MPEG_VIDEO_H264_8X8_TRANSFORM control
media: venus: venc: Add support for intra-refresh period
media: v4l2-ctrls: Add intra-refresh period control
media: docs: ext-ctrls-codec: Document cyclic intra-refresh zero control value
media: venus: helper: do not set constrained parameters for UBWC
media: venus: venc: Fix potential null pointer dereference on pointer fmt
media: venus: hfi: fix return value check in sys_get_prop_image_version()
media: tegra-cec: Handle errors of clk_prepare_enable()
media: cec-pin: rename timer overrun variables
media: TDA1997x: report -ENOLINK after disconnecting HDMI source
media: TDA1997x: fix tda1997x_query_dv_timings() return value
media: Fix cosmetic error in TDA1997x driver
media: v4l2-dv-timings.c: fix wrong condition in two for-loops
media: imx: add a driver for i.MX8MQ mipi csi rx phy and controller
media: dt-bindings: media: document the nxp,imx8mq-mipi-csi2 receiver phy and controller
media: imx: imx7_mipi_csis: convert some switch cases to the default
media: imx: imx7-media-csi: Fix buffer return upon stream start failure
media: imx: imx7-media-csi: Don't set PIXEL_BIT in CSICR1
media: imx: imx7-media-csi: Set TWO_8BIT_SENSOR for >= 10-bit formats
media: dt-bindings: media: nxp,imx7-csi: Add i.MX8MM support
...
-----BEGIN PGP SIGNATURE-----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=4uWF
-----END PGP SIGNATURE-----
Merge tag 'for-5.15/drivers-2021-08-30' of git://git.kernel.dk/linux-block
Pull block driver updates from Jens Axboe:
"Sitting on top of the core block changes, here are the driver changes
for the 5.15 merge window:
- NVMe updates via Christoph:
- suspend improvements for devices with an HMB (Keith Busch)
- handle double completions more gacefull (Sagi Grimberg)
- cleanup the selects for the nvme core code a bit (Sagi Grimberg)
- don't update queue count when failing to set io queues (Ruozhu Li)
- various nvmet connect fixes (Amit Engel)
- cleanup lightnvm leftovers (Keith Busch, me)
- small cleanups (Colin Ian King, Hou Pu)
- add tracing for the Set Features command (Hou Pu)
- CMB sysfs cleanups (Keith Busch)
- add a mutex_destroy call (Keith Busch)
- remove lightnvm subsystem. It's served its purpose and ultimately
led to zoned nvme support, we no longer need it (Christoph)
- revert floppy O_NDELAY fix (Denis)
- nbd fixes (Hou, Pavel, Baokun)
- nbd locking fixes (Tetsuo)
- nbd device removal fixes (Christoph)
- raid10 rcu warning fix (Xiao)
- raid1 write behind fix (Guoqing)
- rnbd fixes (Gioh, Md Haris)
- misc fixes (Colin)"
* tag 'for-5.15/drivers-2021-08-30' of git://git.kernel.dk/linux-block: (42 commits)
Revert "floppy: reintroduce O_NDELAY fix"
raid1: ensure write behind bio has less than BIO_MAX_VECS sectors
md/raid10: Remove unnecessary rcu_dereference in raid10_handle_discard
nbd: remove nbd->destroy_complete
nbd: only return usable devices from nbd_find_unused
nbd: set nbd->index before releasing nbd_index_mutex
nbd: prevent IDR lookups from finding partially initialized devices
nbd: reset NBD to NULL when restarting in nbd_genl_connect
nbd: add missing locking to the nbd_dev_add error path
nvme: remove the unused NVME_NS_* enum
nvme: remove nvm_ndev from ns
nvme: Have NVME_FABRICS select NVME_CORE instead of transport drivers
block: nbd: add sanity check for first_minor
nvmet: check that host sqsize does not exceed ctrl MQES
nvmet: avoid duplicate qid in connect cmd
nvmet: pass back cntlid on successful completion
nvme-rdma: don't update queue count when failing to set io queues
nvme-tcp: don't update queue count when failing to set io queues
nvme-tcp: pair send_mutex init with destroy
nvme: allow user toggling hmb usage
...
A stop gap for potential future speculation related hardware
vulnerabilities and a mechanism for truly security paranoid
applications.
It allows a task to request that the L1D cache is flushed when the kernel
switches to a different mm. This can be requested via prctl().
Changes vs. the previous versions:
- Get rid of the software flush fallback
- Make the handling consistent with other mitigations
- Kill the task when it ends up on a SMT enabled core which defeats the
purpose of L1D flushing obviously
-----BEGIN PGP SIGNATURE-----
iQJHBAABCgAxFiEEQp8+kY+LLUocC4bMphj1TA10mKEFAmEsn0oTHHRnbHhAbGlu
dXRyb25peC5kZQAKCRCmGPVMDXSYoa5fD/47vHGtjAtDr/DaXR1C6F9AvVbKEl8p
oNHn8IukE6ts6G4dFH9wUvo/Ut0K3kxX54I+BATew0LTy6tsQeUYh/xjwXMupgNV
oKOc9waoqdFvju3ayLFWJmuACLdXpyrGC1j35Aji61zSbR/GdtZ4oDxbuN2YJDAT
BTcgKrBM5nQm94JNa083RQSCU5LJxbC7ETkIh6NR73RSPCjUC1Wpxy1sAQAa2MPD
8EzcJ/DjVGaHCI7adX10sz3xdUcyOz7qYz16HpoMGx+oSiq7pGEBtUiK97EYMcrB
s+ADFUjYmx/pbEWv2r4c9zxNh7ZV3aLBsWwi7bScHIsv8GjrsA/mYLWskuwOV6BB
22qZjfd0c4raiJwd+nmSx+D2Szv6lZ20gP+krtP2VNC6hUv7ft0VPLySiaFMmUHj
quooDZis/W5n+4C9Q8Rk9uUtKzzJOngqW+duftiixHiNQ/ECP/QCAHhZYck/NOkL
tZkNj6lJj9+2iR7mhbYROZ+wrYQzRvqNb2pJJQoi/wA0q7wPSKBi3m+51lPsht5W
tn94CpaDDZ4IB7Fe1NtcA0UpYJSWpDQGlau4qp92HMCCIcRFfQEm+m9x8axwcj7m
ECblHJYBPHuNcCHvPA8kHvr1nd6UUXrGPIo8TK8YhUUbK6pO0OjdNzZX496ia/2g
pLzaW2ENTPLbXg==
=27wH
-----END PGP SIGNATURE-----
Merge tag 'x86-cpu-2021-08-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 cache flush updates from Thomas Gleixner:
"A reworked version of the opt-in L1D flush mechanism.
This is a stop gap for potential future speculation related hardware
vulnerabilities and a mechanism for truly security paranoid
applications.
It allows a task to request that the L1D cache is flushed when the
kernel switches to a different mm. This can be requested via prctl().
Changes vs the previous versions:
- Get rid of the software flush fallback
- Make the handling consistent with other mitigations
- Kill the task when it ends up on a SMT enabled core which defeats
the purpose of L1D flushing obviously"
* tag 'x86-cpu-2021-08-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Documentation: Add L1D flushing Documentation
x86, prctl: Hook L1D flushing in via prctl
x86/mm: Prepare for opt-in based L1D flush in switch_mm()
x86/process: Make room for TIF_SPEC_L1D_FLUSH
sched: Add task_work callback for paranoid L1D flush
x86/mm: Refactor cond_ibpb() to support other use cases
x86/smp: Add a per-cpu view of SMT state
Lightnvm supports the OCSSD 1.x and 2.0 specs which were early attempts
to produce Open Channel SSDs and never made it into the NVMe spec
proper. They have since been superceeded by NVMe enhancements such
as ZNS support. Remove the support per the deprecation schedule.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20210812132308.38486-1-hch@lst.de
Reviewed-by: Matias Bjørling <mb@lightnvm.io>
Reviewed-by: Javier González <javier@javigon.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add a control to set intra-refresh period.
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In all drivers _CYCLIC_INTRA_REFRESH_MB default control value is zero
which means that the macroblocks will not be intra-refreshed. Document
this _CYCLIC_INTRA_REFRESH_MB control behaviour in control description.
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Improve the documentation of the frame rate configuration so that it can
be understood by a regular human being.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The V4L2_CID_PIXEL_RATE is nowadays used to tell pixel sampling rate in
the sub-device's pixel array, not the pixel rate over a link (for which it
also becomes unfit with the addition of multiplexed streams later on). Fix
this.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix kerneldoc syntax in v4l2-async. The references were not produced
correctly.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Modernise the documentation to make it more precise and update the use of
pixel rate control and various other changes. In particular:
- Use non-proportional font for file names, properties as well as
controls.
- The unit of the HBLANK control is pixels, not lines.
- The unit of PIXEL_RATE control is pixels per second, not Hz.
- Merge common requirements for CSI-2 and parallel busses.
- Include all DT properties needed for assigned clocks.
- Fix referencing the link rate control.
- SMIA driver's new name is CCS driver.
- The PIXEL_RATE control denotes pixel rate on the pixel array on camera
sensors. Do not suggest it is used to tell the maximum pixel rate on the
bus anymore.
- Improve ReST syntax (plain struct and function names).
- Remove the suggestion to use s_power() in receiver drivers.
- Make MIPI website URL use HTTPS, add Wikipedia links to BT.601 and
BT.656.
Fixes: e4cf8c58af ("media: Documentation: media: Document how to write camera sensor drivers")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add documentation of l1d flushing, explain the need for the
feature and how it can be used.
Signed-off-by: Balbir Singh <sblbir@amazon.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20210108121056.21940-6-sblbir@amazon.com
If HEVC frame consists of multiple slices, segment address has to be
known in order to properly decode it.
Add segment address field to slice parameters.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix typo in a define: CEC_OP_REC_SEQ_SATERDAY -> CEC_OP_REC_SEQ_SATURDAY
This isn't used yet in actual applications to the best of my knowledge,
and it certainly doesn't break the ABI since the value doesn't change.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Here is the big set of char / misc and other driver subsystem updates
for 5.14-rc1. Included in here are:
- habanna driver updates
- fsl-mc driver updates
- comedi driver updates
- fpga driver updates
- extcon driver updates
- interconnect driver updates
- mei driver updates
- nvmem driver updates
- phy driver updates
- pnp driver updates
- soundwire driver updates
- lots of other tiny driver updates for char and misc drivers
This is looking more and more like the "various driver subsystems mushed
together" tree...
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYOM8jQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymECgCg0yL+8WxDKO5Gg5llM5PshvLB1rQAn0y5pDgg
nw78LV3HQ0U7qaZBtI91
=x+AR
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc driver updates from Greg KH:
"Here is the big set of char / misc and other driver subsystem updates
for 5.14-rc1. Included in here are:
- habanalabs driver updates
- fsl-mc driver updates
- comedi driver updates
- fpga driver updates
- extcon driver updates
- interconnect driver updates
- mei driver updates
- nvmem driver updates
- phy driver updates
- pnp driver updates
- soundwire driver updates
- lots of other tiny driver updates for char and misc drivers
This is looking more and more like the "various driver subsystems
mushed together" tree...
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (292 commits)
mcb: Use DEFINE_RES_MEM() helper macro and fix the end address
PNP: moved EXPORT_SYMBOL so that it immediately followed its function/variable
bus: mhi: pci-generic: Add missing 'pci_disable_pcie_error_reporting()' calls
bus: mhi: Wait for M2 state during system resume
bus: mhi: core: Fix power down latency
intel_th: Wait until port is in reset before programming it
intel_th: msu: Make contiguous buffers uncached
intel_th: Remove an unused exit point from intel_th_remove()
stm class: Spelling fix
nitro_enclaves: Set Bus Master for the NE PCI device
misc: ibmasm: Modify matricies to matrices
misc: vmw_vmci: return the correct errno code
siox: Simplify error handling via dev_err_probe()
fpga: machxo2-spi: Address warning about unused variable
lkdtm/heap: Add init_on_alloc tests
selftests/lkdtm: Enable various testable CONFIGs
lkdtm: Add CONFIG hints in errors where possible
lkdtm: Enable DOUBLE_FAULT on all architectures
lkdtm/heap: Add vmalloc linear overflow test
lkdtm/bugs: XFAIL UNALIGNED_LOAD_STORE_WRITE
...
The close on exec flag is O_CLOEXEC, not O_EXEC. This patch just fixes
the typo.
Suggested-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Rodrigo Campos <rodrigo@kinvolk.io>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Fixes: 0ae71c7720 ("seccomp: Support atomic "addfd + send reply"")
Link: https://lore.kernel.org/r/20210702151927.263402-1-rodrigo@kinvolk.io
Highlights:
- New think-lmi driver adding support for changing BIOS settings from
within Linux using the standard firmware-attributes class sysfs API
- MS Surface aggregator-cdev now also supports forwarding events to
user-space (for debugging / new driver development purposes only)
- New intel_skl_int3472 driver this provides the necessary glue to
translate ACPI table information to GPIOs, regulators, etc. for
camera sensors on Intel devices with IPU3 attached MIPI cameras
- A whole bunch of other fixes + device-specific quirk additions
- New devm_work_autocancel() devm-helpers.h function
Note this also contains merges of the following immutable branches/tags
shared with other subsystems:
- platform-drivers-x86-goodix-v5.14-1
- intel-gpio-v5.14-1
- linux-pm/acpi-scan
- devm-helpers-v5.14-1
The following is an automated git shortlog grouped by driver:
ACPI:
- scan: initialize local variable to avoid garbage being returned
- scan: Add function to fetch dependent of ACPI device
- scan: Extend acpi_walk_dep_device_list()
- scan: Rearrange dep_unmet initialization
Add intel_skl_int3472 driver:
- Add intel_skl_int3472 driver
ISST:
- Use numa node id for cpu pci dev mapping
- Optimize CPU to PCI device mapping
Input:
- goodix - platform/x86: touchscreen_dmi - Move upside down quirks to touchscreen_dmi.c
MAINTAINERS:
- Update IRC link for Surface System Aggregator subsystem
- Update info for telemetry
Merge remote-tracking branch 'linux-pm/acpi-scan' into review-hans:
- Merge remote-tracking branch 'linux-pm/acpi-scan' into review-hans
Merge tag 'devm-helpers-v5.14-1' into review-hans:
- Merge tag 'devm-helpers-v5.14-1' into review-hans
Merge tag 'intel-gpio-v5.14-1' into review-hans:
- Merge tag 'intel-gpio-v5.14-1' into review-hans
Merge tag 'platform-drivers-x86-goodix-v5.14-1' into review-hans:
- Merge tag 'platform-drivers-x86-goodix-v5.14-1' into review-hans
Remove "default n" entries:
- Remove "default n" entries
Rename hp-wireless to wireless-hotkey:
- Rename hp-wireless to wireless-hotkey
asus-nb-wmi:
- Revert "add support for ASUS ROG Zephyrus G14 and G15"
- Revert "Drop duplicate DMI quirk structures"
dcdbas:
- drop unneeded assignment in host_control_smi()
dell-privacy:
- Add support for Dell hardware privacy
dell-wmi:
- Rename dell-wmi.c to dell-wmi-base.c
dell-wmi-sysman:
- Change user experience when Admin/System Password is modified
- fw_attr_inuse can be static
- Use firmware_attributes_class helper
- Make populate_foo_data functions more robust
dell-wmi-sysman/think-lmi:
- Make fw_attr_class global static
devm-helpers:
- Add resource managed version of work init
docs:
- driver-api: Update Surface Aggregator user-space interface documentation
extcon:
- extcon-max8997: Simplify driver using devm
- extcon-max8997: Fix IRQ freeing at error path
- extcon-max77693.c: Fix potential work-queue cancellation race
- extcon-max14577: Fix potential work-queue cancellation race
firmware_attributes_class:
- Create helper file for handling firmware-attributes class registration events
gpio:
- wcove: Split error handling for CTRL and IRQ registers
- wcove: Unify style of to_reg() with to_ireg()
- wcove: Use IRQ hardware number getter instead of direct access
- crystalcove: remove platform_set_drvdata() + cleanup probe
gpiolib:
- acpi: Add acpi_gpio_get_io_resource()
- acpi: Introduce acpi_get_and_request_gpiod() helper
hdaps:
- Constify static attribute_group struct
ideapad-laptop:
- Ignore VPC event bit 10
intel_cht_int33fe:
- Move to its own subfolder
- Correct "displayport" fwnode reference
intel_ips:
- fix set but unused warning in read_mgtv
intel_pmt_crashlog:
- Constify static attribute_group struct
intel_skl_int3472:
- Uninitialized variable in skl_int3472_handle_gpio_resources()
- Move to intel/ subfolder
- Provide skl_int3472_unregister_clock()
- Provide skl_int3472_unregister_regulator()
- Use ACPI GPIO resource directly
- Fix dependencies (drop CLKDEV_LOOKUP)
- Free ACPI device resources after use
mfd:
- tps68470: Remove tps68470 MFD driver
platform/mellanox:
- mlxreg-hotplug: Revert "move to use request_irq by IRQF_NO_AUTOEN flag"
platform/surface:
- aggregator: Use list_move_tail instead of list_del/list_add_tail in ssh_packet_layer.c
- aggregator: Use list_move_tail instead of list_del/list_add_tail in ssh_request_layer.c
- aggregator: Drop unnecessary variable initialization
- aggregator: Do not return uninitialized value
- aggregator_cdev: Add lockdep support
- aggregator_cdev: Allow enabling of events from user-space
- aggregator_cdev: Add support for forwarding events to user-space
- aggregator: Update copyright
- aggregator: Allow enabling of events without notifiers
- aggregator: Allow registering notifiers without enabling events
- dtx: Add missing mutex_destroy() call in failure path
- aggregator: Fix event disable function
- aggregator_registry: Consolidate node groups for 5th- and 6th-gen devices
- aggregator_registry: Add support for 13" Intel Surface Laptop 4
- aggregator_registry: Update comments for 15" AMD Surface Laptop 4
samsung-laptop:
- set debugfs blobs to read only
- use octal numbers for rwx file permissions
tc1100-wmi:
- Constify static attribute_group struct
think-lmi:
- Move kfree(setting->possible_values) to tlmi_attr_setting_release()
- Split current_value to reflect only the value
- Fix issues with duplicate attributes
- Return EINVAL when kbdlang gets set to a 0 length string
- Add missing MODULE_DEVICE_TABLE
- Avoid potential read before start of the buffer
- Fix check for admin password being set
- Add WMI interface support on Lenovo platforms
thinkpad-lmi:
- Remove unused display_name member from struct tlmi_pwd_setting
thinkpad_acpi:
- Add X1 Carbon Gen 9 second fan support
- Fix inconsistent indenting
tools/power/x86/intel-speed-select:
- v1.10 release
- Fix uncore memory frequency display
toshiba_acpi:
- Fix missing error code in toshiba_acpi_setup_keyboard()
toshiba_haps:
- Fix missing newline in pr_debug call in toshiba_haps_notify
touchscreen_dmi:
- Fix Chuwi Hi10 Pro comment
- Add info for the Goodix GT912 panel of TM800A550L tablets
- Add an extra entry for the upside down Goodix touchscreen on Teclast X89 tablets
x86/platform/uv:
- Constify static attribute_group struct
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEEuvA7XScYQRpenhd+kuxHeUQDJ9wFAmDbELwUHGhkZWdvZWRl
QHJlZGhhdC5jb20ACgkQkuxHeUQDJ9yp2wgAj1mTOJi/4Rx1g8wXLpP/hflEkFMU
yyMeKe3LOEzuo/LZUfW4tqWiXa4aTgN6rUOF8KUumsIor/72hKcczuPVY+qCqF7V
qYZ0vMG93DfAyVPQvBrNjHMXiVevD/gMFRqJEOOgXt96B6Zea4vh1pBvLACAHFZ0
bjkZDX3cO89TSfUF7uhiU9UkMvMMAVs34Knc1Pe4QnZ16e2kPGcKip3qb73yT+xC
8NVRgE6fdSIJfDAVzqpdh91rfDdzHDJ6vT10uijOTkriJciN07UKtYuK5StCpAo5
sXIQllHySHRHj5N0IWZ04w6RMQ+l/9CaHDttkYWW3fV1EU9SVzvp/+d6zA==
=tAuE
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v5.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver updates from Hans de Goede:
"Highlights:
- New think-lmi driver adding support for changing Lenovo Thinkpad
BIOS settings from within Linux using the standard firmware-
attributes class sysfs API
- MS Surface aggregator-cdev now also supports forwarding events to
user-space (for debugging / new driver development purposes only)
- New intel_skl_int3472 driver this provides the necessary glue to
translate ACPI table information to GPIOs, regulators, etc. for
camera sensors on Intel devices with IPU3 attached MIPI cameras
- A whole bunch of other fixes + device-specific quirk additions
- New devm_work_autocancel() devm-helpers.h function"
* tag 'platform-drivers-x86-v5.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (83 commits)
platform/x86: dell-wmi-sysman: Change user experience when Admin/System Password is modified
platform/x86: intel_skl_int3472: Uninitialized variable in skl_int3472_handle_gpio_resources()
platform/x86: think-lmi: Move kfree(setting->possible_values) to tlmi_attr_setting_release()
platform/x86: think-lmi: Split current_value to reflect only the value
platform/x86: think-lmi: Fix issues with duplicate attributes
platform/x86: think-lmi: Return EINVAL when kbdlang gets set to a 0 length string
platform/x86: intel_cht_int33fe: Move to its own subfolder
platform/x86: intel_skl_int3472: Move to intel/ subfolder
platform/x86: intel_skl_int3472: Provide skl_int3472_unregister_clock()
platform/x86: intel_skl_int3472: Provide skl_int3472_unregister_regulator()
platform/x86: intel_skl_int3472: Use ACPI GPIO resource directly
platform/x86: intel_skl_int3472: Fix dependencies (drop CLKDEV_LOOKUP)
platform/x86: intel_skl_int3472: Free ACPI device resources after use
platform/x86: Remove "default n" entries
platform/x86: ISST: Use numa node id for cpu pci dev mapping
platform/x86: ISST: Optimize CPU to PCI device mapping
tools/power/x86/intel-speed-select: v1.10 release
tools/power/x86/intel-speed-select: Fix uncore memory frequency display
extcon: extcon-max8997: Simplify driver using devm
extcon: extcon-max8997: Fix IRQ freeing at error path
...
- Some kernel-doc cleanups. That script is still regex onslaught from
hell, but it has gotten a little better.
- Improvements to the checkpatch docs, which are also used by the tool
itself.
- A major update to the pathname lookup documentation.
- Elimination of :doc: markup, since our automarkup magic can create
references from filenames without all the extra noise.
- The flurry of Chinese translation activity continues.
Plus, of course, the usual collection of updates, typo fixes, and warning
fixes.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAmDZ6pQPHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5Y9W0IAIpzBZDVsDQ7s5cIjbxEh9Oeh1uRmwuObnQh
xsM5oLuAUSMczf5JX8cdyutWJfdoEF5WHjfbt1otfys+kW9m7z0b1K4xw684Y390
sPk3eYVYLiUAZ4/LVdC47BpAzzgJ5U9iC6+FjOATAYsY40EwruxyZWjmY+SaDOU5
dQPjbpRuNQTFjYE6nZIW0o6jyunrfFaJTS6g2bdDoBDOGKyNOSKEw4XZ442cJ3km
uXoMfSJGslQj6qbGY0YhNeaNQm0ErcQw2K4lS3K4gc7Lht32Fbi1lhaqnTIkgI5f
Rh3X37pb90Ya88uWxldVB2bXUrA+PZA/cJqwNTrgw+niBQl6sKU=
=KDcM
-----END PGP SIGNATURE-----
Merge tag 'docs-5.14' of git://git.lwn.net/linux
Pull documentation updates from Jonathan Corbet:
"This was a reasonably active cycle for documentation; this includes:
- Some kernel-doc cleanups. That script is still regex onslaught from
hell, but it has gotten a little better.
- Improvements to the checkpatch docs, which are also used by the
tool itself.
- A major update to the pathname lookup documentation.
- Elimination of :doc: markup, since our automarkup magic can create
references from filenames without all the extra noise.
- The flurry of Chinese translation activity continues.
Plus, of course, the usual collection of updates, typo fixes, and
warning fixes"
* tag 'docs-5.14' of git://git.lwn.net/linux: (115 commits)
docs: path-lookup: use bare function() rather than literals
docs: path-lookup: update symlink description
docs: path-lookup: update get_link() ->follow_link description
docs: path-lookup: update WALK_GET, WALK_PUT desc
docs: path-lookup: no get_link()
docs: path-lookup: update i_op->put_link and cookie description
docs: path-lookup: i_op->follow_link replaced with i_op->get_link
docs: path-lookup: Add macro name to symlink limit description
docs: path-lookup: remove filename_mountpoint
docs: path-lookup: update do_last() part
docs: path-lookup: update path_mountpoint() part
docs: path-lookup: update path_to_nameidata() part
docs: path-lookup: update follow_managed() part
docs: Makefile: Use CONFIG_SHELL not SHELL
docs: Take a little noise out of the build process
docs: x86: avoid using ReST :doc:`foo` markup
docs: virt: kvm: s390-pv-boot.rst: avoid using ReST :doc:`foo` markup
docs: userspace-api: landlock.rst: avoid using ReST :doc:`foo` markup
docs: trace: ftrace.rst: avoid using ReST :doc:`foo` markup
docs: trace: coresight: coresight.rst: avoid using ReST :doc:`foo` markup
...
-----BEGIN PGP SIGNATURE-----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=VQX8
-----END PGP SIGNATURE-----
Merge tag 'media/v5.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- V4L2 core control API was split into separate files
- New RC maps: tango and tc-90405
- Hantro driver got support for G2/HEVC decoder
- av7710 is moving to staging, together with some legacy APIs
- several cleanups related to compat_ioctl32 code
- Move the MPEG-2 stateless control type out of staging
- Address several issues with RPM get logic on media drivers
- Lots of cleanups, bug fixes and improvements.
* tag 'media/v5.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (394 commits)
media: s5p-mfc: Fix display delay control creation
media: mtk-vpu: on suspend, read/write regs only if vpu is running
media: video-mux: Skip dangling endpoints
media: Fix Media Controller API config checks
media: i2c: rdacm20: Re-work ov10635 reset
media: i2c: rdacm20: Check return values
media: i2c: rdacm20: Report camera module name
media: i2c: rdacm20: Enable noise immunity
media: i2c: rdacm20: Embed 'serializer' field
media: i2c: rdacm21: Power up OV10640 before OV490
media: i2c: rdacm21: Fix OV10640 powerup
media: i2c: rdacm21: Add delay after OV490 reset
media: i2c: max9271: Introduce wake_up() function
media: i2c: max9271: Check max9271_write() return
media: i2c: max9286: Rework comments in .bound()
media: i2c: max9286: Define high channel amplitude
media: i2c: max9286: Cache channel amplitude
media: i2c: max9286: Rename reverse_channel_mv
media: i2c: max9286: Adjust parameters indent
media: hantro: add support for Rockchip RK3036
...
Alban Crequy reported a race condition userspace faces when we want to
add some fds and make the syscall return them[1] using seccomp notify.
The problem is that currently two different ioctl() calls are needed by
the process handling the syscalls (agent) for another userspace process
(target): SECCOMP_IOCTL_NOTIF_ADDFD to allocate the fd and
SECCOMP_IOCTL_NOTIF_SEND to return that value. Therefore, it is possible
for the agent to do the first ioctl to add a file descriptor but the
target is interrupted (EINTR) before the agent does the second ioctl()
call.
This patch adds a flag to the ADDFD ioctl() so it adds the fd and
returns that value atomically to the target program, as suggested by
Kees Cook[2]. This is done by simply allowing
seccomp_do_user_notification() to add the fd and return it in this case.
Therefore, in this case the target wakes up from the wait in
seccomp_do_user_notification() either to interrupt the syscall or to add
the fd and return it.
This "allocate an fd and return" functionality is useful for syscalls
that return a file descriptor only, like connect(2). Other syscalls that
return a file descriptor but not as return value (or return more than
one fd), like socketpair(), pipe(), recvmsg with SCM_RIGHTs, will not
work with this flag.
This effectively combines SECCOMP_IOCTL_NOTIF_ADDFD and
SECCOMP_IOCTL_NOTIF_SEND into an atomic opteration. The notification's
return value, nor error can be set by the user. Upon successful invocation
of the SECCOMP_IOCTL_NOTIF_ADDFD ioctl with the SECCOMP_ADDFD_FLAG_SEND
flag, the notifying process's errno will be 0, and the return value will
be the file descriptor number that was installed.
[1]: https://lore.kernel.org/lkml/CADZs7q4sw71iNHmV8EOOXhUKJMORPzF7thraxZYddTZsxta-KQ@mail.gmail.com/
[2]: https://lore.kernel.org/lkml/202012011322.26DCBC64F2@keescook/
Signed-off-by: Rodrigo Campos <rodrigo@kinvolk.io>
Signed-off-by: Sargun Dhillon <sargun@sargun.me>
Acked-by: Tycho Andersen <tycho@tycho.pizza>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20210517193908.3113-4-sargun@sargun.me
-----BEGIN PGP SIGNATURE-----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=79iZ
-----END PGP SIGNATURE-----
Merge tag 'for-5.14/libata-2021-06-27' of git://git.kernel.dk/linux-block
Pull libata updates from Jens Axboe:
"The big change in this round is that we're finally in a position where
we can sanely remove the old drivers/ide/ code, as libata covers
everything we need by now.
This is exciting for two reasons:
1) we delete a lot of legacy code that doesn't really meet the
standards we have today, and
2) it enables us to clean up various bits in the block layer that
exist only because of the old IDE code.
Outside of that, just a few minor fixes here, fixups for warnings,
etc"
* tag 'for-5.14/libata-2021-06-27' of git://git.kernel.dk/linux-block: (29 commits)
ata: rb532_cf: remove redundant codes
ide: remove the legacy ide driver
m68k: use libata instead of the legacy ide driver
ARM: disable CONFIG_IDE in pxa_defconfig
ARM: disable CONFIG_IDE in footbridge_defconfig
alpha: use libata instead of the legacy ide driver
pata_cypress: add a module option to disable BM-DMA
ata: pata_macio: Avoid overwriting initialised field in 'pata_macio_sht'
ata: pata_serverworks: Avoid overwriting initialised field in 'serverworks_osb4_sht
ata: pata_sc1200: sc1200_sht'Avoid overwriting initialised field in '
ata: pata_cs5530: Avoid overwriting initialised field in 'cs5530_sht'
ata: pata_cs5520: Avoid overwriting initialised field in 'cs5520_sht'
ata: pata_atiixp: Avoid overwriting initialised field in 'atiixp_sht'
ata: sata_nv: Do not over-write initialise fields in 'nv_adma_sht' and 'nv_swncq_sht'
ata: sata_mv: Do not over-write initialise fields in 'mv6_sht'
ata: sata_sil24: Do not over-write initialise fields in 'sil24_sht'
ata: ahci: Ensure initialised fields are not overwritten in AHCI_SHT()
ata: include: libata: Move fields commonly over-written to separate MACRO
ahci: Add support for Dell S140 and later controllers
ata: ahci_sunxi: Disable DIPM
...
Currently, debugging unknown events requires writing a custom driver.
This is somewhat difficult, slow to adapt, and not entirely
user-friendly for quickly trying to figure out things on devices of some
third-party user. We can do better. We already have a user-space
interface intended for debugging SAM EC requests, so let's add support
for receiving events to that.
This commit provides support for receiving events by reading from the
controller file. It additionally introduces two new IOCTLs to control
which event categories will be forwarded. Specifically, a user-space
client can specify which target categories it wants to receive events
from by registering the corresponding notifier(s) via the IOCTLs and
after that, read the received events by reading from the controller
device.
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210604134755.535590-5-luzmaximilian@gmail.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The legay ide driver has been replace with libata starting in 2003 and has
been scheduled for removal for a while. Finally kill it off so that we
can start cleaning up various bits of cruft it forced on the block layer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The :doc:`foo` tag is auto-generated via automarkup.py.
So, use the filename at the sources, instead of :doc:`foo`.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The :doc:`foo` tag is auto-generated via automarkup.py.
So, use the filename at the sources, instead of :doc:`foo`.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The HEVC HANTRO driver needs to know the number of bits to skip at
the beginning of the slice header.
That is a hardware specific requirement so create a dedicated control
for this purpose.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add decode params control and the associated structure to group
all the information that are needed to decode a reference frame as
is described in ITU-T Rec. H.265 section "8.3.2 Decoding process
for reference picture set".
Adapt Cedrus driver to these changes.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add fields and flags as they are defined in
7.4.3.3.1 "General picture parameter set RBSP semantics of the
H.265 ITU specification.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
sps_max_sub_layers_minus1 is needed if the driver wishes to determine
whether or not a frame might be used for reference.
Signed-off-by: John Cox <jc@kynesim.co.uk>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The only upstream driver using the API described there is the
av7110 driver.
As the driver was moved to staging, move the API bits to staging
as well.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The conversion tools used during DocBook/LaTeX/html/Markdown->ReST
conversion and some cut-and-pasted text contain some characters that
aren't easily reachable on standard keyboards and/or could cause
troubles when parsed by the documentation build system.
Replace the occurences of the following characters:
- U+00a0 (' '): NO-BREAK SPACE
as it can cause lines being truncated on PDF output
- U+2019 ('’'): RIGHT SINGLE QUOTATION MARK
- U+201c ('“'): LEFT DOUBLE QUOTATION MARK
- U+201d ('”'): RIGHT DOUBLE QUOTATION MARK
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The conversion tools used during DocBook/LaTeX/html/Markdown->ReST
conversion and some cut-and-pasted text contain some characters that
aren't easily reachable on standard keyboards and/or could cause
troubles when parsed by the documentation build system.
Replace the occurences of the following characters:
- U+00a0 (' '): NO-BREAK SPACE
as it can cause lines being truncated on PDF output
- U+2014 ('—'): EM DASH
- U+2019 ('’'): RIGHT SINGLE QUOTATION MARK
Note that Sphinx auto-translates '---' into EM DASH.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The conversion tools used during DocBook/LaTeX/html/Markdown->ReST
conversion and some cut-and-pasted text contain some characters that
aren't easily reachable on standard keyboards and/or could cause
troubles when parsed by the documentation build system.
Replace the occurences of the following characters:
- U+201c ('“'): LEFT DOUBLE QUOTATION MARK
- U+201d ('”'): RIGHT DOUBLE QUOTATION MARK
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The header defines the user space interface but may be mistaken as
kernel-only header due to its location. Add "uapi" directory under
driver's include directory and move the header there.
Suggested-by: Greg KH <gregkh@linuxfoundation.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmC0CoEeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG8qYH/0bJOUUsj4fsBHY+
1fSTcbEZYxrdO6nYOzk34UZBeC7rGdhpFFVCU0fh/il8ec3K8pU9ypZykhvpFwGD
cY0zrfaNiEcsIinYZh/tMyfPK3JMqGrcOkKqYli5kSfW9BR0YzHBeiETcHMyZfMu
a8uI9nNYIZda0hwrXMbMNaFMH4Nif3kXwDxNNrx1THaTYifVZK+IwlM8TpcSPIK/
eNbU+5G/VBiQ9YE4PZyXVbsWMZcJ9NDRanx6aKMYTlwSDytxmd5HlURKJcfOiXnQ
AQq9VYbkkuw6FhBPnWvkYVJj1UwkySXjXyZkTiIH8iIMpJ406rWrQgIaQPI3o/98
iVDfH9k=
=t88B
-----END PGP SIGNATURE-----
Merge tag 'v5.13-rc4' into media_tree
Linux 5.13-rc4
* tag 'v5.13-rc4': (976 commits)
Linux 5.13-rc4
seccomp: Refactor notification handler to prepare for new semantics
selftests: kvm: fix overlapping addresses in memslot_perf_test
KVM: X86: Kill off ctxt->ud
KVM: X86: Fix warning caused by stale emulation context
KVM: X86: Use kvm_get_linear_rip() in single-step and #DB/#BP interception
Documentation: seccomp: Fix user notification documentation
MAINTAINERS: adjust to removing i2c designware platform data
perf vendor events powerpc: Fix eventcode of power10 JSON events
Revert "serial: 8250: 8250_omap: Fix possible interrupt storm"
i2c: s3c2410: fix possible NULL pointer deref on read message after write
i2c: mediatek: Disable i2c start_en and clear intr_stat brfore reset
perf stat: Fix error check for bpf_program__attach
cifs: change format of CIFS_FULL_KEY_DUMP ioctl
i2c: i801: Don't generate an interrupt on bus reset
i2c: mpc: implement erratum A-004447 workaround
powerpc/fsl: set fsl,i2c-erratum-a004447 flag for P1010 i2c controllers
powerpc/fsl: set fsl,i2c-erratum-a004447 flag for P2041 i2c controllers
dt-bindings: i2c: mpc: Add fsl,i2c-erratum-a004447 flag
i2c: busses: i2c-stm32f4: Remove incorrectly placed ' ' from function name
...
The documentation had some previously incorrect information about how
userspace notifications (and responses) were handled due to a change
from a previously proposed patchset.
Signed-off-by: Sargun Dhillon <sargun@sargun.me>
Acked-by: Tycho Andersen <tycho@tycho.pizza>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Fixes: 6a21cc50f0 ("seccomp: add a return code to trap to userspace")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210517193908.3113-2-sargun@sargun.me
The v4l2-ctrls.c source has become much too big, so split it up
into four separate parts:
v4l2-ctrls-core.c: contains the core framework code
v4l2-ctrls-api.c: contains the uAPI interface to the framework
v4l2-ctrls-defs.c: contains the control definitions
v4l2-ctrls-request.c: contains the Request API helpers
And it adds a new v4l2-ctrls-priv.h.
No code was changed, but a number of checkpatch.pl warnings were
fixed (alignment, f == NULL -> !f, long comment block coding style,
unsigned -> unsigned int).
The copyright statements were updated as well since they were
quite out of date.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Until now, the MPEG-2 V4L2 API was not exported as a public API,
and only defined in a private media header (media/mpeg2-ctrls.h).
After reviewing the MPEG-2 specification in detail, and reworking
the controls so they match the MPEG-2 semantics properly,
we can consider it ready.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The Hantro and Cedrus drivers work in frame-mode,
meaning they expect all the slices in a picture (either frame
or field structure) to be passed in each OUTPUT buffer.
These two are the only V4L2 MPEG-2 stateless decoders currently
supported. Given the VA-API drivers also work per-frame,
coalescing all the MPEG-2 slices in a buffer before the decoding
operation, it makes sense to not expect slice-mode drivers and
therefore remove V4L2_CID_MPEG_VIDEO_MPEG2_SLICE_PARAMS.
This is done to avoid carrying an unused interface. If needed,
this control can be added without breaking backwards compatibility.
Note that this would mean introducing a enumerator control to
specify the decoding mode (see V4L2_CID_STATELESS_H264_DECODE_MODE).
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Co-developed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The forward and backwards references are specified per-picture
and not per-slice. Move it to V4L2_CID_MPEG_VIDEO_MPEG2_PICTURE.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Typically, bitstreams are composed of a sequence header,
followed by a number of picture header and picture coding extension
headers. Each picture can be composed of a number of slices.
Let's split the MPEG-2 uAPI to follow these semantics more closely,
allowing more usage flexibility. Having these controls split up
allows applications to set a sequence control at the beginning
of a sequence, and then set a picture control for each frame.
While here add padding fields where needed, and document
the uAPI header thoroughly.
Note that the V4L2_CTRL_TYPE_{} defines had to be moved because
it clashes with existing ones. This is not really an issue
since they will be re-defined when the controls are moved
out of staging.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Jonas Karlman <jonas@kwiboo.se>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Our current MPEG-2 uAPI uses 1-byte fields for MPEG-2
boolean syntax elements. Clean these by adding a 'flags'
field and flag macro for each boolean syntax element.
A follow-up change will refactor this uAPI so we don't need
to add padding fields just yet.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Jonas Karlman <jonas@kwiboo.se>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As stated in the MPEG-2 specification, section 6.3.7 "Quant matrix
extension":
Each quantisation matrix has a default set of values. When a
sequence_header_code is decoded all matrices shall be reset to
their default values. User defined matrices may be downloaded
and this can occur in a sequence_header() or in a
quant_matrix_extension().
The load_intra_quantiser_matrix syntax elements are transmitted
in the bitstream headers, signalling that a quantisation matrix
needs to be loaded and used for pictures transmitted afterwards
(until the matrices are reset).
This "load" semantics are implemented in the V4L2 interface
without the need of any "load" flags: passing the control
is effectively a load.
Therefore, rework the V4L2_CID_MPEG_VIDEO_MPEG2_QUANTISATION
semantics to match the MPEG-2 semantics. Quantisation matrices
values are now initialized by the V4L2 control core to their
reset default value, and applications are expected to reset
their values as specified.
The quantisation control is therefore optional, and used to
load bitstream-defined values in the quantisation matrices.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Co-developed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The MPEG-2 specification refers to the quantisation matrices
using the word "quantisation". Make the V4L2 interface more
ergonomic by matching the MPEG-2 spec.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Dependent slice segment flag for PPS control is misnamed. It should have
"enabled" at the end. It only tells if this flag is present in slice
header or not and not the actual value.
Fix this by renaming the PPS flag and introduce another flag for slice
control which tells actual value.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
-----BEGIN PGP SIGNATURE-----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=uCN4
-----END PGP SIGNATURE-----
Merge tag 'landlock_v34' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull Landlock LSM from James Morris:
"Add Landlock, a new LSM from Mickaël Salaün.
Briefly, Landlock provides for unprivileged application sandboxing.
From Mickaël's cover letter:
"The goal of Landlock is to enable to restrict ambient rights (e.g.
global filesystem access) for a set of processes. Because Landlock
is a stackable LSM [1], it makes possible to create safe security
sandboxes as new security layers in addition to the existing
system-wide access-controls. This kind of sandbox is expected to
help mitigate the security impact of bugs or unexpected/malicious
behaviors in user-space applications. Landlock empowers any
process, including unprivileged ones, to securely restrict
themselves.
Landlock is inspired by seccomp-bpf but instead of filtering
syscalls and their raw arguments, a Landlock rule can restrict the
use of kernel objects like file hierarchies, according to the
kernel semantic. Landlock also takes inspiration from other OS
sandbox mechanisms: XNU Sandbox, FreeBSD Capsicum or OpenBSD
Pledge/Unveil.
In this current form, Landlock misses some access-control features.
This enables to minimize this patch series and ease review. This
series still addresses multiple use cases, especially with the
combined use of seccomp-bpf: applications with built-in sandboxing,
init systems, security sandbox tools and security-oriented APIs [2]"
The cover letter and v34 posting is here:
https://lore.kernel.org/linux-security-module/20210422154123.13086-1-mic@digikod.net/
See also:
https://landlock.io/
This code has had extensive design discussion and review over several
years"
Link: https://lore.kernel.org/lkml/50db058a-7dde-441b-a7f9-f6837fe8b69f@schaufler-ca.com/ [1]
Link: https://lore.kernel.org/lkml/f646e1c7-33cf-333f-070c-0a40ad0468cd@digikod.net/ [2]
* tag 'landlock_v34' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
landlock: Enable user space to infer supported features
landlock: Add user and kernel documentation
samples/landlock: Add a sandbox manager example
selftests/landlock: Add user space tests
landlock: Add syscall implementations
arch: Wire up Landlock syscalls
fs,security: Add sb_delete hook
landlock: Support filesystem access-control
LSM: Infrastructure management of the superblock
landlock: Add ptrace restrictions
landlock: Set up the security framework and manage credentials
landlock: Add ruleset and domain management
landlock: Add object management
Core:
- bpf:
- allow bpf programs calling kernel functions (initially to
reuse TCP congestion control implementations)
- enable task local storage for tracing programs - remove the
need to store per-task state in hash maps, and allow tracing
programs access to task local storage previously added for
BPF_LSM
- add bpf_for_each_map_elem() helper, allowing programs to
walk all map elements in a more robust and easier to verify
fashion
- sockmap: support UDP and cross-protocol BPF_SK_SKB_VERDICT
redirection
- lpm: add support for batched ops in LPM trie
- add BTF_KIND_FLOAT support - mostly to allow use of BTF
on s390 which has floats in its headers files
- improve BPF syscall documentation and extend the use of kdoc
parsing scripts we already employ for bpf-helpers
- libbpf, bpftool: support static linking of BPF ELF files
- improve support for encapsulation of L2 packets
- xdp: restructure redirect actions to avoid a runtime lookup,
improving performance by 4-8% in microbenchmarks
- xsk: build skb by page (aka generic zerocopy xmit) - improve
performance of software AF_XDP path by 33% for devices
which don't need headers in the linear skb part (e.g. virtio)
- nexthop: resilient next-hop groups - improve path stability
on next-hops group changes (incl. offload for mlxsw)
- ipv6: segment routing: add support for IPv4 decapsulation
- icmp: add support for RFC 8335 extended PROBE messages
- inet: use bigger hash table for IP ID generation
- tcp: deal better with delayed TX completions - make sure we don't
give up on fast TCP retransmissions only because driver is
slow in reporting that it completed transmitting the original
- tcp: reorder tcp_congestion_ops for better cache locality
- mptcp:
- add sockopt support for common TCP options
- add support for common TCP msg flags
- include multiple address ids in RM_ADDR
- add reset option support for resetting one subflow
- udp: GRO L4 improvements - improve 'forward' / 'frag_list'
co-existence with UDP tunnel GRO, allowing the first to take
place correctly even for encapsulated UDP traffic
- micro-optimize dev_gro_receive() and flow dissection, avoid
retpoline overhead on VLAN and TEB GRO
- use less memory for sysctls, add a new sysctl type, to allow using
u8 instead of "int" and "long" and shrink networking sysctls
- veth: allow GRO without XDP - this allows aggregating UDP
packets before handing them off to routing, bridge, OvS, etc.
- allow specifing ifindex when device is moved to another namespace
- netfilter:
- nft_socket: add support for cgroupsv2
- nftables: add catch-all set element - special element used
to define a default action in case normal lookup missed
- use net_generic infra in many modules to avoid allocating
per-ns memory unnecessarily
- xps: improve the xps handling to avoid potential out-of-bound
accesses and use-after-free when XPS change race with other
re-configuration under traffic
- add a config knob to turn off per-cpu netdev refcnt to catch
underflows in testing
Device APIs:
- add WWAN subsystem to organize the WWAN interfaces better and
hopefully start driving towards more unified and vendor-
-independent APIs
- ethtool:
- add interface for reading IEEE MIB stats (incl. mlx5 and
bnxt support)
- allow network drivers to dump arbitrary SFP EEPROM data,
current offset+length API was a poor fit for modern SFP
which define EEPROM in terms of pages (incl. mlx5 support)
- act_police, flow_offload: add support for packet-per-second
policing (incl. offload for nfp)
- psample: add additional metadata attributes like transit delay
for packets sampled from switch HW (and corresponding egress
and policy-based sampling in the mlxsw driver)
- dsa: improve support for sandwiched LAGs with bridge and DSA
- netfilter:
- flowtable: use direct xmit in topologies with IP
forwarding, bridging, vlans etc.
- nftables: counter hardware offload support
- Bluetooth:
- improvements for firmware download w/ Intel devices
- add support for reading AOSP vendor capabilities
- add support for virtio transport driver
- mac80211:
- allow concurrent monitor iface and ethernet rx decap
- set priority and queue mapping for injected frames
- phy: add support for Clause-45 PHY Loopback
- pci/iov: add sysfs MSI-X vector assignment interface
to distribute MSI-X resources to VFs (incl. mlx5 support)
New hardware/drivers:
- dsa: mv88e6xxx: add support for Marvell mv88e6393x -
11-port Ethernet switch with 8x 1-Gigabit Ethernet
and 3x 10-Gigabit interfaces.
- dsa: support for legacy Broadcom tags used on BCM5325, BCM5365
and BCM63xx switches
- Microchip KSZ8863 and KSZ8873; 3x 10/100Mbps Ethernet switches
- ath11k: support for QCN9074 a 802.11ax device
- Bluetooth: Broadcom BCM4330 and BMC4334
- phy: Marvell 88X2222 transceiver support
- mdio: add BCM6368 MDIO mux bus controller
- r8152: support RTL8153 and RTL8156 (USB Ethernet) chips
- mana: driver for Microsoft Azure Network Adapter (MANA)
- Actions Semi Owl Ethernet MAC
- can: driver for ETAS ES58X CAN/USB interfaces
Pure driver changes:
- add XDP support to: enetc, igc, stmmac
- add AF_XDP support to: stmmac
- virtio:
- page_to_skb() use build_skb when there's sufficient tailroom
(21% improvement for 1000B UDP frames)
- support XDP even without dedicated Tx queues - share the Tx
queues with the stack when necessary
- mlx5:
- flow rules: add support for mirroring with conntrack,
matching on ICMP, GTP, flex filters and more
- support packet sampling with flow offloads
- persist uplink representor netdev across eswitch mode
changes
- allow coexistence of CQE compression and HW time-stamping
- add ethtool extended link error state reporting
- ice, iavf: support flow filters, UDP Segmentation Offload
- dpaa2-switch:
- move the driver out of staging
- add spanning tree (STP) support
- add rx copybreak support
- add tc flower hardware offload on ingress traffic
- ionic:
- implement Rx page reuse
- support HW PTP time-stamping
- octeon: support TC hardware offloads - flower matching on ingress
and egress ratelimitting.
- stmmac:
- add RX frame steering based on VLAN priority in tc flower
- support frame preemption (FPE)
- intel: add cross time-stamping freq difference adjustment
- ocelot:
- support forwarding of MRP frames in HW
- support multiple bridges
- support PTP Sync one-step timestamping
- dsa: mv88e6xxx, dpaa2-switch: offload bridge port flags like
learning, flooding etc.
- ipa: add IPA v4.5, v4.9 and v4.11 support (Qualcomm SDX55, SM8350,
SC7280 SoCs)
- mt7601u: enable TDLS support
- mt76:
- add support for 802.3 rx frames (mt7915/mt7615)
- mt7915 flash pre-calibration support
- mt7921/mt7663 runtime power management fixes
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=vcbA
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- bpf:
- allow bpf programs calling kernel functions (initially to
reuse TCP congestion control implementations)
- enable task local storage for tracing programs - remove the
need to store per-task state in hash maps, and allow tracing
programs access to task local storage previously added for
BPF_LSM
- add bpf_for_each_map_elem() helper, allowing programs to walk
all map elements in a more robust and easier to verify fashion
- sockmap: support UDP and cross-protocol BPF_SK_SKB_VERDICT
redirection
- lpm: add support for batched ops in LPM trie
- add BTF_KIND_FLOAT support - mostly to allow use of BTF on
s390 which has floats in its headers files
- improve BPF syscall documentation and extend the use of kdoc
parsing scripts we already employ for bpf-helpers
- libbpf, bpftool: support static linking of BPF ELF files
- improve support for encapsulation of L2 packets
- xdp: restructure redirect actions to avoid a runtime lookup,
improving performance by 4-8% in microbenchmarks
- xsk: build skb by page (aka generic zerocopy xmit) - improve
performance of software AF_XDP path by 33% for devices which don't
need headers in the linear skb part (e.g. virtio)
- nexthop: resilient next-hop groups - improve path stability on
next-hops group changes (incl. offload for mlxsw)
- ipv6: segment routing: add support for IPv4 decapsulation
- icmp: add support for RFC 8335 extended PROBE messages
- inet: use bigger hash table for IP ID generation
- tcp: deal better with delayed TX completions - make sure we don't
give up on fast TCP retransmissions only because driver is slow in
reporting that it completed transmitting the original
- tcp: reorder tcp_congestion_ops for better cache locality
- mptcp:
- add sockopt support for common TCP options
- add support for common TCP msg flags
- include multiple address ids in RM_ADDR
- add reset option support for resetting one subflow
- udp: GRO L4 improvements - improve 'forward' / 'frag_list'
co-existence with UDP tunnel GRO, allowing the first to take place
correctly even for encapsulated UDP traffic
- micro-optimize dev_gro_receive() and flow dissection, avoid
retpoline overhead on VLAN and TEB GRO
- use less memory for sysctls, add a new sysctl type, to allow using
u8 instead of "int" and "long" and shrink networking sysctls
- veth: allow GRO without XDP - this allows aggregating UDP packets
before handing them off to routing, bridge, OvS, etc.
- allow specifing ifindex when device is moved to another namespace
- netfilter:
- nft_socket: add support for cgroupsv2
- nftables: add catch-all set element - special element used to
define a default action in case normal lookup missed
- use net_generic infra in many modules to avoid allocating
per-ns memory unnecessarily
- xps: improve the xps handling to avoid potential out-of-bound
accesses and use-after-free when XPS change race with other
re-configuration under traffic
- add a config knob to turn off per-cpu netdev refcnt to catch
underflows in testing
Device APIs:
- add WWAN subsystem to organize the WWAN interfaces better and
hopefully start driving towards more unified and vendor-
independent APIs
- ethtool:
- add interface for reading IEEE MIB stats (incl. mlx5 and bnxt
support)
- allow network drivers to dump arbitrary SFP EEPROM data,
current offset+length API was a poor fit for modern SFP which
define EEPROM in terms of pages (incl. mlx5 support)
- act_police, flow_offload: add support for packet-per-second
policing (incl. offload for nfp)
- psample: add additional metadata attributes like transit delay for
packets sampled from switch HW (and corresponding egress and
policy-based sampling in the mlxsw driver)
- dsa: improve support for sandwiched LAGs with bridge and DSA
- netfilter:
- flowtable: use direct xmit in topologies with IP forwarding,
bridging, vlans etc.
- nftables: counter hardware offload support
- Bluetooth:
- improvements for firmware download w/ Intel devices
- add support for reading AOSP vendor capabilities
- add support for virtio transport driver
- mac80211:
- allow concurrent monitor iface and ethernet rx decap
- set priority and queue mapping for injected frames
- phy: add support for Clause-45 PHY Loopback
- pci/iov: add sysfs MSI-X vector assignment interface to distribute
MSI-X resources to VFs (incl. mlx5 support)
New hardware/drivers:
- dsa: mv88e6xxx: add support for Marvell mv88e6393x - 11-port
Ethernet switch with 8x 1-Gigabit Ethernet and 3x 10-Gigabit
interfaces.
- dsa: support for legacy Broadcom tags used on BCM5325, BCM5365 and
BCM63xx switches
- Microchip KSZ8863 and KSZ8873; 3x 10/100Mbps Ethernet switches
- ath11k: support for QCN9074 a 802.11ax device
- Bluetooth: Broadcom BCM4330 and BMC4334
- phy: Marvell 88X2222 transceiver support
- mdio: add BCM6368 MDIO mux bus controller
- r8152: support RTL8153 and RTL8156 (USB Ethernet) chips
- mana: driver for Microsoft Azure Network Adapter (MANA)
- Actions Semi Owl Ethernet MAC
- can: driver for ETAS ES58X CAN/USB interfaces
Pure driver changes:
- add XDP support to: enetc, igc, stmmac
- add AF_XDP support to: stmmac
- virtio:
- page_to_skb() use build_skb when there's sufficient tailroom
(21% improvement for 1000B UDP frames)
- support XDP even without dedicated Tx queues - share the Tx
queues with the stack when necessary
- mlx5:
- flow rules: add support for mirroring with conntrack, matching
on ICMP, GTP, flex filters and more
- support packet sampling with flow offloads
- persist uplink representor netdev across eswitch mode changes
- allow coexistence of CQE compression and HW time-stamping
- add ethtool extended link error state reporting
- ice, iavf: support flow filters, UDP Segmentation Offload
- dpaa2-switch:
- move the driver out of staging
- add spanning tree (STP) support
- add rx copybreak support
- add tc flower hardware offload on ingress traffic
- ionic:
- implement Rx page reuse
- support HW PTP time-stamping
- octeon: support TC hardware offloads - flower matching on ingress
and egress ratelimitting.
- stmmac:
- add RX frame steering based on VLAN priority in tc flower
- support frame preemption (FPE)
- intel: add cross time-stamping freq difference adjustment
- ocelot:
- support forwarding of MRP frames in HW
- support multiple bridges
- support PTP Sync one-step timestamping
- dsa: mv88e6xxx, dpaa2-switch: offload bridge port flags like
learning, flooding etc.
- ipa: add IPA v4.5, v4.9 and v4.11 support (Qualcomm SDX55, SM8350,
SC7280 SoCs)
- mt7601u: enable TDLS support
- mt76:
- add support for 802.3 rx frames (mt7915/mt7615)
- mt7915 flash pre-calibration support
- mt7921/mt7663 runtime power management fixes"
* tag 'net-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2451 commits)
net: selftest: fix build issue if INET is disabled
net: netrom: nr_in: Remove redundant assignment to ns
net: tun: Remove redundant assignment to ret
net: phy: marvell: add downshift support for M88E1240
net: dsa: ksz: Make reg_mib_cnt a u8 as it never exceeds 255
net/sched: act_ct: Remove redundant ct get and check
icmp: standardize naming of RFC 8335 PROBE constants
bpf, selftests: Update array map tests for per-cpu batched ops
bpf: Add batched ops support for percpu array
bpf: Implement formatted output helpers with bstr_printf
seq_file: Add a seq_bprintf function
sfc: adjust efx->xdp_tx_queue_count with the real number of initialized queues
net:nfc:digital: Fix a double free in digital_tg_recv_dep_req
net: fix a concurrency bug in l2tp_tunnel_register()
net/smc: Remove redundant assignment to rc
mpls: Remove redundant assignment to err
llc2: Remove redundant assignment to rc
net/tls: Remove redundant initialization of record
rds: Remove redundant assignment to nr_sig
dt-bindings: net: mdio-gpio: add compatible for microchip,mdio-smi0
...
well contained to Documentation/ itself. Highlights include:
- The Chinese translators have been busy and show no signs of stopping
anytime soon. Italian has also caught up.
- Aditya Srivastava has been working on improvements to the kernel-doc
script.
- Thorsten continues his work on reporting-issues.rst and related
documentation around regression reporting.
- Lots of documentation updates, typo fixes, etc. as usual
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAmCG5moPHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5YCoUH/1q/O+IvS+JNkxneDxbB6OC799BQpabZHi7/
HbYfgfX0nKrV3NAwIhigsIj6WHRE+5p2rKiHOuQxL3daJyfZSqQl0/yI0Ag7Of4g
7y1FKBQrfqS6tJcyNckdtBfxYUQP9yCJY0xfIexkTNiujbmkMKDSJD7lKXd0AaTM
styCvTbgTPTzadL5bIHj/GxJ9s8DsxO3y9LGdRc+GrNzPFliMYWlJgbR28zjEKBm
UQzy7JGNBX3qTJwgjvv/myqRDy6MligvGrP+wG0KTnAHXKkvDFl3p46kPwzdk1JE
+F5sbboUWh20GLYy9t4MZOcq38FUcEPlRPXkxsGNyA8co5ij8+g=
=7db3
-----END PGP SIGNATURE-----
Merge tag 'docs-5.13' of git://git.lwn.net/linux
Pull documentation updates from Jonathan Corbet:
"It's been a relatively busy cycle in docsland, though more than
usually well contained to Documentation/ itself. Highlights include:
- The Chinese translators have been busy and show no signs of
stopping anytime soon. Italian has also caught up.
- Aditya Srivastava has been working on improvements to the
kernel-doc script.
- Thorsten continues his work on reporting-issues.rst and related
documentation around regression reporting.
- Lots of documentation updates, typo fixes, etc. as usual"
* tag 'docs-5.13' of git://git.lwn.net/linux: (139 commits)
docs/zh_CN: add openrisc translation to zh_CN index
docs/zh_CN: add openrisc index.rst translation
docs/zh_CN: add openrisc todo.rst translation
docs/zh_CN: add openrisc openrisc_port.rst translation
docs/zh_CN: add core api translation to zh_CN index
docs/zh_CN: add core-api index.rst translation
docs/zh_CN: add core-api irq index.rst translation
docs/zh_CN: add core-api irq irqflags-tracing.rst translation
docs/zh_CN: add core-api irq irq-domain.rst translation
docs/zh_CN: add core-api irq irq-affinity.rst translation
docs/zh_CN: add core-api irq concepts.rst translation
docs: sphinx-pre-install: don't barf on beta Sphinx releases
scripts: kernel-doc: improve parsing for kernel-doc comments syntax
docs/zh_CN: two minor fixes in zh_CN/doc-guide/
Documentation: dev-tools: Add Testing Overview
docs/zh_CN: add translations in zh_CN/dev-tools/gcov
docs: reporting-issues: make people CC the regressions list
MAINTAINERS: add regressions mailing list
doc:it_IT: align Italian documentation
docs/zh_CN: sync reporting-issues.rst
...
Here is the big set of tty and serial driver updates for 5.13-rc1.
Actually busy this release, with a number of cleanups happening:
- much needed core tty cleanups by Jiri Slaby
- removal of unused and orphaned old-style serial drivers. If
anyone shows up with this hardware, it is trivial to restore
these but we really do not think they are in use anymore.
- fixes and cleanups from Johan Hovold on a number of termios
setting corner cases that loads of drivers got wrong as well
as removing unneeded code due to tty core changes from long
ago that were never propagated out to the drivers
- loads of platform-specific serial port driver updates and
fixes
- coding style cleanups and other small fixes and updates all
over the tty/serial tree.
All of these have been in linux-next for a while now with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYIa3NQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykMXgCfX3FZgKveI4l94ChXSy4OyKwycHUAn00BzrMC
/7BwA1FnjQnC4zSzuHnm
=bAas
-----END PGP SIGNATURE-----
Merge tag 'tty-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty and serial driver updates from Greg KH:
"Here is the big set of tty and serial driver updates for 5.13-rc1.
Actually busy this release, with a number of cleanups happening:
- much needed core tty cleanups by Jiri Slaby
- removal of unused and orphaned old-style serial drivers. If anyone
shows up with this hardware, it is trivial to restore these but we
really do not think they are in use anymore.
- fixes and cleanups from Johan Hovold on a number of termios setting
corner cases that loads of drivers got wrong as well as removing
unneeded code due to tty core changes from long ago that were never
propagated out to the drivers
- loads of platform-specific serial port driver updates and fixes
- coding style cleanups and other small fixes and updates all over
the tty/serial tree.
All of these have been in linux-next for a while now with no reported
issues"
* tag 'tty-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (186 commits)
serial: extend compile-test coverage
serial: stm32: add FIFO threshold configuration
dt-bindings: serial: 8250: update TX FIFO trigger level
dt-bindings: serial: stm32: override FIFO threshold properties
dt-bindings: serial: add RX and TX FIFO properties
serial: xilinx_uartps: drop low-latency workaround
serial: vt8500: drop low-latency workaround
serial: timbuart: drop low-latency workaround
serial: sunsu: drop low-latency workaround
serial: sifive: drop low-latency workaround
serial: txx9: drop low-latency workaround
serial: sa1100: drop low-latency workaround
serial: rp2: drop low-latency workaround
serial: rda: drop low-latency workaround
serial: owl: drop low-latency workaround
serial: msm_serial: drop low-latency workaround
serial: mpc52xx_uart: drop low-latency workaround
serial: meson: drop low-latency workaround
serial: mcf: drop low-latency workaround
serial: lpc32xx_hs: drop low-latency workaround
...
Here is the big set of staging and IIO driver updates for 5.13-rc1.
Lots of little churn in here, and some larger churn as well. Major
things are:
- removal of wimax drivers, no one has this hardware anymore for
this failed "experiment".
- removal of the Google gasket driver, turns out no one wanted
to maintain it or cares about it anymore, so they asked for it
to be removed.
- comedi finally moves out of the staging directory into
drivers/comedi/ This is one of the oldest kernel subsystems
around, being created in the 2.0 kernel days, and was one of
the first things added to drivers/staging/ when that was
created over 15 years ago. It should have been moved out of
staging a long time ago, it's well maintained and used by
loads of different devices in the real world every day. Nice
to see this finally happen.
- so many tiny coding style cleanups it's not funny. Perfect
storm of at least 2 different intern project application
deadlines combined to provide a huge number of new
contributions in this area from people learning how to do
kernel development. Great job to everyone involved here.
There's also the normal updates for IIO drivers with new IIO drivers and
updates all over that subsystem.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYIa1zw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfMACgq/Qj9n6NO/P4BX55XWjRkjOmxxwAoKrYEWkG
fIdLmhh4FGWkxaJO3Izf
=PCXb
-----END PGP SIGNATURE-----
Merge tag 'staging-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO driver updates from Greg KH:
"Here is the big set of staging and IIO driver updates for 5.13-rc1.
Lots of little churn in here, and some larger churn as well. Major
things are:
- removal of wimax drivers, no one has this hardware anymore for this
failed "experiment".
- removal of the Google gasket driver, turns out no one wanted to
maintain it or cares about it anymore, so they asked for it to be
removed.
- comedi finally moves out of the staging directory into drivers/comedi
This is one of the oldest kernel subsystems around, being created
in the 2.0 kernel days, and was one of the first things added to
drivers/staging/ when that was created over 15 years ago.
It should have been moved out of staging a long time ago, it's well
maintained and used by loads of different devices in the real world
every day. Nice to see this finally happen.
- so many tiny coding style cleanups it's not funny.
Perfect storm of at least 2 different intern project application
deadlines combined to provide a huge number of new contributions in
this area from people learning how to do kernel development. Great
job to everyone involved here.
There's also the normal updates for IIO drivers with new IIO drivers
and updates all over that subsystem.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (907 commits)
staging: octeon: Use 'for_each_child_of_node'
Staging: rtl8723bs: rtw_xmit: fixed tabbing issue
staging: rtl8188eu: remove unused function parameters
staging: rtl8188eu: cmdThread is a task_struct
staging: rtl8188eu: remove constant variable and dead code
staging: rtl8188eu: change bLeisurePs' type to bool
staging: rtl8723bs: remove empty #ifdef block
staging: rtl8723bs: remove unused DBG_871X_LEVEL macro declarations
staging: rtl8723bs: split too long line
staging: rtl8723bs: fix indentation in if block
staging: rtl8723bs: fix code indent issue
staging: rtl8723bs: replace DBG_871X_LEVEL logs with netdev_*()
staging: rtl8192e: indent statement properly
staging: rtl8723bs: Remove led_blink_hdl() and everything related
staging: comedi: move out of staging directory
staging: rtl8723bs: remove sdio_drv_priv structure
staging: rtl8723bs: remove unused argument in function
staging: rtl8723bs: remove DBG_871X_SEL_NL macro declaration
staging: rtl8723bs: replace DBG_871X_SEL_NL with netdev_dbg()
staging: rtl8723bs: fix indentation issue introduced by long line split
...
Add a first document describing userspace API: how to define and enforce
a Landlock security policy. This is explained with a simple example.
The Landlock system calls are described with their expected behavior and
current limitations.
Another document is dedicated to kernel developers, describing guiding
principles and some important kernel structures.
This documentation can be built with the Sphinx framework.
Cc: James Morris <jmorris@namei.org>
Cc: Jann Horn <jannh@google.com>
Cc: Serge E. Hallyn <serge@hallyn.com>
Signed-off-by: Mickaël Salaün <mic@linux.microsoft.com>
Reviewed-by: Vincent Dagonneau <vincent.dagonneau@ssi.gouv.fr>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20210422154123.13086-13-mic@digikod.net
Signed-off-by: James Morris <jamorris@linux.microsoft.com>
The rx-arb-lost error injection command only works with <op> set to 'any'.
Explicitly say so in the usage message.
Also use [] to indicate that the <poll> argument is optional.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Long Term Reference (LTR) frames are the frames that are encoded
sometime in the past and stored in the DPB buffer list to be used
as reference to encode future frames.
This change adds controls to enable this feature.
Signed-off-by: Dikshita Agarwal <dikshita@codeaurora.org>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
:c:type:`struct v4l2_requestbuffers` should be
struct :c:type:`v4l2_requestbuffers`.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The VIDIOC_G/S/TRY_EXT_CTRLS documentation has large explanatory texts for
some of the fields in a table. This makes it hard to read. Move those text
to a new cell spanning the whole width of the table, similar to what was
done for struct v4l2_pix_format. This makes it much more readable.
Also move the 'ctrl_class' description to below the 'which' description and
just mention that it is deprecated and that 'which' should be used instead.
Finally remove 'note::' for the V4L2_CTRL_WHICH_DEF_VAL description. It
doesn't have to be marked as a note, it's just a simple paragraph.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The _FRAME_SKIP_ enums were missing the _VIDEO prefix.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The media bus bit width of MEDIA_BUS_FMT_RGB101010_1X30 is 30.
So, 'Bit31' and 'Bit30' cells for the 'MEDIA_BUS_FMT_RGB101010_1X30'
row should be spaces instead of '0's.
Fixes: 54f38fcae5 ("media: docs: move uAPI book to userspace-api/media")
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The added format is V4L2_PIX_FMT_YUV24, this is a packed
YUV 4:4:4 format, with 8 bits for each component, 24 bits
per sample.
This format is used by the i.MX 8QuadMax and i.MX 8DualXPlus/8QuadXPlus
JPEG encoder/decoder.
Signed-off-by: Mirela Rabulea <mirela.rabulea@nxp.com>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The documentation for V4L2_CID_MPEG_VIDEO_BITRATE was missing the word
'Average': this is the average video bitrate.
The V4L2_CID_MPEG_VIDEO_BITRATE_PEAK documentation *does* refer to
V4L2_CID_MPEG_VIDEO_BITRATE as the average video bitrate.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Until now, the VP8 V4L2 API was not exported as a public API,
and only defined in a private media header (media/vp8-ctrls.h).
The reason for this was a concern about the API not complete
and ready to support VP8 decoding hardware accelerators.
After reviewing the VP8 specification in detail, and now
that the API is able to support Cedrus and Hantro G1,
we can consider this ready.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Since we are ready to stabilize the VP8 stateless API,
move the parsed VP8 pixel format.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rename to struct v4l2_vp8_loop_filter, which is closer to the
VP8 syntax. This change is only cosmetics, but since this API
is exposed to userspace, it's worth the trouble to get it consistent.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
It doesn't seem to add any clarity to have a "header" suffix in controls,
struct names and flags.
Since this just makes names too long without any benefit, just drop it.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add a control to enable inserting of AUD NALU into encoded
bitstream.
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Deprecate mfc private display delay and display enable controls for
new clients and use the standard controls instead.
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Make display delay and display delay enable MFC controls standard v4l
controls. This will allow reuse of the controls for other decoder
drivers. Also the new proposed controls are now codec agnostic because
they could be used for any codec.
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The Microsoft Surface Book series devices consist of a so-called
clipboard part (containing the CPU, touchscreen, and primary battery)
and a base part (containing keyboard, secondary battery, and optional
discrete GPU). These parts can be separated, i.e. the clipboard can be
detached and used as tablet.
This detachment process is initiated by pressing a button. On the
Surface Book 2 and 3 (targeted with this commit), the Surface Aggregator
Module (i.e. the embedded controller on those devices) attempts to send
a notification to any listening client driver and waits for further
instructions (i.e. whether the detachment process should continue or be
aborted). If it does not receive a response in a certain time-frame, the
detachment process (by default) continues and the clipboard can be
physically separated. In other words, (by default and) without a driver,
the detachment process takes about 10 seconds to complete.
This commit introduces a driver for this detachment system (called DTX).
This driver allows a user-space daemon to control and influence the
detachment behavior. Specifically, it forwards any detachment requests
to user-space, allows user-space to make such requests itself, and
allows handling of those requests. Requests can be handled by either
aborting, continuing/allowing, or delaying (i.e. resetting the timeout
via a heartbeat commend). The user-space API is implemented via the
/dev/surface/dtx miscdevice.
In addition, user-space can change the default behavior on timeout from
allowing detachment to disallowing it, which is useful if the (optional)
discrete GPU is in use.
Furthermore, this driver allows user-space to receive notifications
about the state of the base, specifically when it is physically removed
(as opposed to detachment requested), in what manner it is connected
(i.e. in reverse-/tent-/studio- or laptop-mode), and what type of base
is connected. Based on this information, the driver also provides a
simple tablet-mode switch (aliasing all modes without keyboard access,
i.e. tablet-mode and studio-mode to its reported tablet-mode).
An implementation of such a user-space daemon, allowing configuration of
detachment behavior via scripts (e.g. safely unmounting USB devices
connected to the base before continuing) can be found at [1].
[1]: https://github.com/linux-surface/surface-dtx-daemon
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/20210308184819.437438-2-luzmaximilian@gmail.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Currently, only the 'i' 0x90 ioctl() actually exists and is defined in
'include/uapi/linux/iio/events.h'.
It's the IIO_GET_EVENT_FD_IOCTL, which is used to retrieve and FD for
reading events from an IIO device.
We will want to add more ioct() numbers, so with this change the 'i'
0x90-0x9F space is reserved for IIO ioctl() calls.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20210215104043.91251-8-alexandru.ardelean@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
As some hardware have a knob to enable or disable emulation prevention
bytes removal, driver writers ended up wondering what exactly the
START_CODE_NONE modes meant in this regards. This patch clarify what is
expected with a reference to the specification.
Reported-by: John Cox <jc@kynesim.co.uk>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sphinx doesn't allow placing those cross-reference identifies
everywhere. Misplacing them cause those warnings:
Documentation/userspace-api/media/v4l/hist-v4l2.rst:818: WARNING: undefined label: control-flags (if the link has no caption the label must precede a section header)
Documentation/userspace-api/media/v4l/hist-v4l2.rst:853: WARNING: undefined label: reserved-formats (if the link has no caption the label must precede a section header)
Documentation/userspace-api/media/v4l/pixfmt-v4l2.rst:47: WARNING: undefined label: reserved-formats (if the link has no caption the label must precede a section header)
Documentation/userspace-api/media/v4l/subdev-formats.rst:39: WARNING: undefined label: v4l2-subdev-mbus-code-flags (if the link has no caption the label must precede a section header)
Documentation/userspace-api/media/v4l/subdev-formats.rst:53: WARNING: undefined label: v4l2-subdev-mbus-code-flags (if the link has no caption the label must precede a section header)
Documentation/userspace-api/media/v4l/subdev-formats.rst:67: WARNING: undefined label: v4l2-subdev-mbus-code-flags (if the link has no caption the label must precede a section header)
Documentation/userspace-api/media/v4l/subdev-formats.rst:83: WARNING: undefined label: v4l2-subdev-mbus-code-flags (if the link has no caption the label must precede a section header)
Documentation/userspace-api/media/v4l/subdev-formats.rst:97: WARNING: undefined label: v4l2-subdev-mbus-code-flags (if the link has no caption the label must precede a section header)
Documentation/userspace-api/media/v4l/subdev-formats.rst:140: WARNING: undefined label: v4l2-subdev-mbus-code-flags (if the link has no caption the label must precede a section header)
Documentation/userspace-api/media/v4l/vidioc-decoder-cmd.rst:75: WARNING: undefined label: decoder-cmds (if the link has no caption the label must precede a section header)
Documentation/userspace-api/media/v4l/vidioc-dqevent.rst:234: WARNING: undefined label: control-flags (if the link has no caption the label must precede a section header)
Documentation/userspace-api/media/v4l/vidioc-g-dv-timings.rst:156: WARNING: undefined label: dv-bt-flags (if the link has no caption the label must precede a section header)
Documentation/userspace-api/media/v4l/vidioc-g-ext-ctrls.rst:41: WARNING: undefined label: ctrl-class (if the link has no caption the label must precede a section header)
Documentation/userspace-api/media/v4l/vidioc-g-ext-ctrls.rst:246: WARNING: undefined label: ctrl-class (if the link has no caption the label must precede a section header)
Documentation/userspace-api/media/v4l/vidioc-g-ext-ctrls.rst:269: WARNING: undefined label: ctrl-class (if the link has no caption the label must precede a section header)
Documentation/userspace-api/media/v4l/vidioc-g-modulator.rst💯 WARNING: undefined label: modulator-txsubchans (if the link has no caption the label must precede a section header)
Documentation/userspace-api/media/v4l/vidioc-g-tuner.rst:119: WARNING: undefined label: tuner-rxsubchans (if the link has no caption the label must precede a section header)
Documentation/userspace-api/media/v4l/vidioc-queryctrl.rst:167: WARNING: undefined label: control-flags (if the link has no caption the label must precede a section header)
Documentation/userspace-api/media/v4l/vidioc-queryctrl.rst:245: WARNING: undefined label: control-flags (if the link has no caption the label must precede a section header)
Documentation/userspace-api/media/v4l/vidioc-queryctrl.rst:396: WARNING: undefined label: ctrl-class (if the link has no caption the label must precede a section header)
Documentation/userspace-api/media/v4l/vidioc-subdev-enum-mbus-code.rst:73: WARNING: undefined label: v4l2-subdev-mbus-code-flags (if the link has no caption the label must precede a section header)
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
It makes more sense to place the xvideo example at the body,
keeping the footnote only to justify the design decision.
While this makes the text better, it also fixes the PDF
output.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There are lots of tables that are not properly displayed
in LaTeX/PDF.
Fix the tablecolumns, add longtable where needed and LaTeX
formatting macros, in order to address such issues.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add missing format macros for the tables there to be properly
output.
While here, also remove the empty ".. note::" markup.
It should be noticed that ".. [1]" markups will generate footnotes,
and not a note within the main text body.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The Picture Parameter Set Flags table for H-264 doesn't output
well on PDF. There are missing format instructions for LaTeX, and
the columns are too long.
Reduce the size of the second column, as 16 bits is more than enough
for the current flags usage, and add the needed bits for it to be
properly output in PDF format.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sphinx/LaTeX doesn't work well with literal blocks.
Due to that, V4L2_BUF_FLAG_M2M_HOLD_CAPTURE_BUF ends
being writing outside the table (and even outside the page).
We need to not only change the table size and font size, but
also to change the message, in order to avoid this bug.
So, improve the text a little bit, while ensuring that the
literal will be written at the beginning of the second line.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The bayer formats have a subtitle, specifying how many bits
they use. Add a title markup to those, as otherwise they
look weird, specially at the PDF output.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The text is repeating the name of the control, which causes
it to be displayed outside the page with PDF output.
Besides that, this is the only JPEG control doing that. Removing
the name duplication doesn't affect the description, but, instead,
make it nicer.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Those tables nicely fits on PDF output without any hack.
Yet, they are using a very small font, and have tabularcolumns.
Clean it up, and convert it to an ASCII artwork, as it
makes easier to see that no hacks are needed to display it ;-)
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Instead of using "- 1", use "minus one".
The reason is that, if the table is split like:
V4L2_FWHT_FL_COMPONENTS_NUM_MSK 0x00070000 The number of color components
- 1.
One might not realize the meaning of the second line.
As a side effect, using text instead of arabic numbers is
more appropriate for formal documents like this spec.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
While fixing issues with PDF generation, I noticed that
bit 8 was missing for WSS 625 format.
While here, convert the literal block into a tables,
as it becomes more visible.
I opted to move the payload into a separate table, as
Sphinx has troubles with complex nested tables.
This way, it should work fine on both html and LaTeX/PDF
formats.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The default way to document control enums is via tables.
Use one here too. As the table is simple, just use ASCII
artwork.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Those tables have small cells that fit nicely without requiring
line beaks.
So, they don't need tabular columns, as Sphinx/LaTeX
can adjust the width on such tables.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The Cyclades driver was orphaned by commit d459883e6c (MAINTAINERS:
remove two dead e-mail) 13 years ago. Noone stepped up to take care of
them and to fix all the issues the driver has.
On the top of that, there is no way to obtain the firmware for Z cards
from the vendor as cyclades.com ceased to exist.
So it's time to drop the driver with all its traces.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210302062214.29627-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2021-03-09
The following pull-request contains BPF updates for your *net-next* tree.
We've added 90 non-merge commits during the last 17 day(s) which contain
a total of 114 files changed, 5158 insertions(+), 1288 deletions(-).
The main changes are:
1) Faster bpf_redirect_map(), from Björn.
2) skmsg cleanup, from Cong.
3) Support for floating point types in BTF, from Ilya.
4) Documentation for sys_bpf commands, from Joe.
5) Support for sk_lookup in bpf_prog_test_run, form Lorenz.
6) Enable task local storage for tracing programs, from Song.
7) bpf_for_each_map_elem() helper, from Yonghong.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
All userspace ioctls major/magic number should be documented in
Documentation/userspace-api/ioctl/ioctl-number.rst, so add
the entry for <linux/nsfs.h>.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Andrey Vagin <avagin@openvz.org>
Cc: Serge Hallyn <serge@hallyn.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: linux-doc@vger.kernel.org
Cc: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/20210210182248.18101-1-rdunlap@infradead.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Generate the syscall command reference from the UAPI header file and
include it in the main bpf docs page.
Signed-off-by: Joe Stringer <joe@cilium.io>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Quentin Monnet <quentin@isovalent.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/20210302171947.2268128-15-joe@cilium.io
Here is the large set of char/misc/whatever driver subsystem updates for
5.12-rc1. Over time it seems like this tree is collecting more and more
tiny driver subsystems in one place, making it easier for those
maintainers, which is why this is getting larger.
Included in here are:
- coresight driver updates
- habannalabs driver updates
- virtual acrn driver addition (proper acks from the x86
maintainers)
- broadcom misc driver addition
- speakup driver updates
- soundwire driver updates
- fpga driver updates
- amba driver updates
- mei driver updates
- vfio driver updates
- greybus driver updates
- nvmeem driver updates
- phy driver updates
- mhi driver updates
- interconnect driver udpates
- fsl-mc bus driver updates
- random driver fix
- some small misc driver updates (rtsx, pvpanic, etc.)
All of these have been in linux-next for a while, with the only reported
issue being a merge conflict in include/linux/mod_devicetable.h that you
will hit in your tree due to the dfl_device_id addition from the fpga
subsystem in here. The resolution should be simple.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYDZf9w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yk3xgCcCEN+pCJTum+uAzSNH3YKs/onaDgAnRSVwOUw
tNW6n1JhXLYl9f5JdhvS
=MOHs
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the large set of char/misc/whatever driver subsystem updates
for 5.12-rc1. Over time it seems like this tree is collecting more and
more tiny driver subsystems in one place, making it easier for those
maintainers, which is why this is getting larger.
Included in here are:
- coresight driver updates
- habannalabs driver updates
- virtual acrn driver addition (proper acks from the x86 maintainers)
- broadcom misc driver addition
- speakup driver updates
- soundwire driver updates
- fpga driver updates
- amba driver updates
- mei driver updates
- vfio driver updates
- greybus driver updates
- nvmeem driver updates
- phy driver updates
- mhi driver updates
- interconnect driver udpates
- fsl-mc bus driver updates
- random driver fix
- some small misc driver updates (rtsx, pvpanic, etc.)
All of these have been in linux-next for a while, with the only
reported issue being a merge conflict due to the dfl_device_id
addition from the fpga subsystem in here"
* tag 'char-misc-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (311 commits)
spmi: spmi-pmic-arb: Fix hw_irq overflow
Documentation: coresight: Add PID tracing description
coresight: etm-perf: Support PID tracing for kernel at EL2
coresight: etm-perf: Clarify comment on perf options
ACRN: update MAINTAINERS: mailing list is subscribers-only
regmap: sdw-mbq: use MODULE_LICENSE("GPL")
regmap: sdw: use no_pm routines for SoundWire 1.2 MBQ
regmap: sdw: use _no_pm functions in regmap_read/write
soundwire: intel: fix possible crash when no device is detected
MAINTAINERS: replace my with email with replacements
mhi: Fix double dma free
uapi: map_to_7segment: Update example in documentation
uio: uio_pci_generic: don't fail probe if pdev->irq equals to IRQ_NOTCONNECTED
drivers/misc/vmw_vmci: restrict too big queue size in qp_host_alloc_queue
firewire: replace tricky statement by two simple ones
vme: make remove callback return void
firmware: google: make coreboot driver's remove callback return void
firmware: xilinx: Use explicit values for all enum values
sample/acrn: Introduce a sample of HSM ioctl interface usage
virt: acrn: Introduce an interface for Service VM to control vCPU
...
Introduce an initial driver for CXL 2.0 Type-3 Memory Devices. CXL is
Compute Express Link which released the 2.0 specification in November.
The Linux relevant changes in CXL 2.0 are support for an OS to
dynamically assign address space to memory devices, support for
switches, persistent memory, and hotplug. A Type-3 Memory Device is a
PCI enumerated device presenting the CXL Memory Device Class Code and
implementing the CXL.mem protocol. CXL.mem allows device to advertise
CPU and I/O coherent memory to the system, i.e. typical "System RAM" and
"Persistent Memory" in Linux /proc/iomem terms.
In addition to the CXL.mem fast path there is an administrative command
hardware mailbox interface for maintenance and provisioning. It is this
command interface that is the focus of the initial driver. With this
driver a CXL device that is mapped by the BIOS can be administered by
Linux. Linux support for CXL PMEM and dynamic CXL address space
management are to be implemented post v5.12.
4cdadfd5e0 cxl/mem: Introduce a driver for CXL-2.0-Type-3 endpoints
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
8adaf747c9 cxl/mem: Find device capabilities
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
b39cb1052a cxl/mem: Register CXL memX devices
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
13237183c7 cxl/mem: Add a "RAW" send command
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
472b1ce6e9 cxl/mem: Enable commands via CEL
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
57ee605b97 cxl/mem: Add set of informational commands
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
-----BEGIN PGP SIGNATURE-----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=3SAQ
-----END PGP SIGNATURE-----
Merge tag 'cxl-for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull initial support for CXL (Compute Express Link) from Dan Williams:
"Introduce an initial driver for CXL 2.0 Type-3 Memory Devices.
CXL is Compute Express Link which released the 2.0 specification in
November. The Linux relevant changes in CXL 2.0 are support for an OS
to dynamically assign address space to memory devices, support for
switches, persistent memory, and hotplug.
A Type-3 Memory Device is a PCI enumerated device presenting the CXL
Memory Device Class Code and implementing the CXL.mem protocol.
CXL.mem allows device to advertise CPU and I/O coherent memory to the
system, i.e. typical "System RAM" and "Persistent Memory" in Linux
/proc/iomem terms.
In addition to the CXL.mem fast path there is an administrative
command hardware mailbox interface for maintenance and provisioning.
It is this command interface that is the focus of the initial driver.
With this driver a CXL device that is mapped by the BIOS can be
administered by Linux.
Linux support for CXL PMEM and dynamic CXL address space management
are to be implemented post v5.12"
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
4cdadfd5e0 ("cxl/mem: Introduce a driver for CXL-2.0-Type-3 endpoints")
13237183c7 ("cxl/mem: Add a "RAW" send command")
472b1ce6e9 ("cxl/mem: Enable commands via CEL")
57ee605b97 ("cxl/mem: Add set of informational commands")
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
8adaf747c9 ("cxl/mem: Find device capabilities")
b39cb1052a ("cxl/mem: Register CXL memX devices")
* tag 'cxl-for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
cxl/mem: Fix potential memory leak
cxl/mem: Return -EFAULT if copy_to_user() fails
MAINTAINERS: Add maintainers of the CXL driver
cxl/mem: Add set of informational commands
cxl/mem: Enable commands via CEL
cxl/mem: Add a "RAW" send command
cxl/mem: Add basic IOCTL interface
cxl/mem: Register CXL memX devices
cxl/mem: Find device capabilities
cxl/mem: Introduce a driver for CXL-2.0-Type-3 endpoints
This series consists of the usual driver updates (ufs, ibmvfc,
qla2xxx, hisi_sas, pm80xx) plus the removal of the gdth driver (which
is bound to cause conflicts with a trivial change somewhere). The
only big major rework of note is the one from Hannes trying to clean
up our result handling code in the drivers to make it consistent.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCYDAdliYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishTblAQCk6wD8
fcb4TItSRp0DpRzs37zhppEbrBgveuAFHhr5swEA0gL2mHcq0vnyNBinCLnERrE7
TPYJqUKJNktnjVG7ZWc=
=wW6p
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This series consists of the usual driver updates (ufs, ibmvfc,
qla2xxx, hisi_sas, pm80xx) plus the removal of the gdth driver (which
is bound to cause conflicts with a trivial change somewhere).
The only big major rework of note is the one from Hannes trying to
clean up our result handling code in the drivers to make it
consistent"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (194 commits)
scsi: MAINTAINERS: Adjust to reflect gdth scsi driver removal
scsi: ufs: Give clk scaling min gear a value
scsi: lpfc: Fix 'physical' typos
scsi: megaraid_mbox: Fix spelling of 'allocated'
scsi: qla2xxx: Simplify the calculation of variables
scsi: message: fusion: Fix 'physical' typos
scsi: target: core: Change ASCQ for residual write
scsi: target: core: Signal WRITE residuals
scsi: target: core: Set residuals for 4Kn devices
scsi: hisi_sas: Add trace FIFO debugfs support
scsi: hisi_sas: Flush workqueue in hisi_sas_v3_remove()
scsi: hisi_sas: Enable debugfs support by default
scsi: hisi_sas: Don't check .nr_hw_queues in hisi_sas_task_prep()
scsi: hisi_sas: Remove deferred probe check in hisi_sas_v2_probe()
scsi: lpfc: Add auto select on IRQ_POLL
scsi: ncr53c8xx: Fix typos
scsi: lpfc: Fix ancient double free
scsi: qla2xxx: Fix some memory corruption
scsi: qla2xxx: Remove redundant NULL check
scsi: megaraid: Fix ifnullfree.cocci warnings
...
- Microsoft Surface devices System Aggregator Module support
- SW_TABLET_MODE reporting improvements
- thinkpad_acpi keyboard language setting support
- platform / DPTF profile settings support
- Base / userspace API parts merged from Rafael's acpi-platform branch
- thinkpad_acpi and ideapad-laptop support through pdx86
- Remove support for some obsolete Intel MID platforms through merging
of the shared intel-mid-removal branch
- Big cleanup of the ideapad-laptop driver
- Misc. other fixes / new hw support / quirks
The following is an automated git shortlog grouped by driver:
ACPI:
- platform-profile: Fix possible deadlock in platform_profile_remove()
- platform-profile: Introduce object pointers to callbacks
- platform-profile: Drop const qualifier for cur_profile
- platform: Add platform profile support
Documentation:
- Add documentation for new platform_profile sysfs attribute
Documentation/ABI:
- sysfs-platform-ideapad-laptop: conservation_mode attribute
- sysfs-platform-ideapad-laptop: update device attribute paths
Kconfig:
- add missing selects for ideapad-laptop
MAINTAINERS:
- update email address for Henrique de Moraes Holschuh
Merge remote-tracking branch 'intel-speed-select/intel-sst' into review-hans:
- Merge remote-tracking branch 'intel-speed-select/intel-sst' into review-hans
Merge remote-tracking branch 'linux-pm/acpi-platform' into review-hans:
- Merge remote-tracking branch 'linux-pm/acpi-platform' into review-hans
Merge tag 'ib-drm-gpio-pdx86-rtc-wdt-v5.12-1' into for-next:
- Merge tag 'ib-drm-gpio-pdx86-rtc-wdt-v5.12-1' into for-next
Move all dell drivers to their own subdirectory:
- Move all dell drivers to their own subdirectory
Platform:
- OLPC: Constify static struct regulator_ops
- OLPC: Specify the enable time
- OLPC: Remove dcon_rdev from olpc_ec_priv
- OLPC: Fix probe error handling
Revert "platform/x86:
- ideapad-laptop: Switch touchpad attribute to be RO"
acer-wmi:
- Don't use ACPI_EXCEPTION()
amd-pmc:
- put device on error paths
- Fix CONFIG_DEBUG_FS check
dell-wmi-sysman:
- fix a NULL pointer dereference
docs:
- driver-api: Add Surface Aggregator subsystem documentation
drm/gma500:
- Get rid of duplicate NULL checks
- Convert to use new SCU IPC API
gpio:
- msic: Remove driver for deprecated platform
- intel-mid: Remove driver for deprecated platform
hp-wmi:
- Disable tablet-mode reporting by default
- Don't log a warning on HPWMI_RET_UNKNOWN_COMMAND errors
i2c-multi-instantiate:
- Don't create platform device for INT3515 ACPI nodes
ideapad-laptop:
- add "always on USB charging" control support
- add keyboard backlight control support
- send notification about touchpad state change to sysfs
- fix checkpatch warnings, more consistent style
- change 'cfg' debugfs file format
- change 'status' debugfs file format
- check for touchpad support in _CFG
- check for Fn-lock support in HALS
- rework is_visible() logic
- rework and create new ACPI helpers
- group and separate (un)related constants into enums
- misc. device attribute changes
- always propagate error codes from device attributes' show() callback
- convert ACPI helpers to return -EIO in case of failure
- use dev_{err,warn} or appropriate variant to display log messages
- use msecs_to_jiffies() helper instead of hand-crafted formula
- use for_each_set_bit() helper to simplify event processing
- use kobj_to_dev()
- use device_{add,remove}_group
- use sysfs_emit()
- add missing call to submodule destructor
- sort includes lexicographically
- use appropriately typed variable to store the return value of ACPI methods
- remove unnecessary NULL checks
- remove unnecessary dev_set_drvdata() call
- DYTC Platform profile support
- Disable touchpad_switch for ELAN0634
intel-vbtn:
- Eval VBDL after registering our notifier
- Add alternative method to enable switches
- Create 2 separate input-devs for buttons and switches
- Rework wakeup handling in notify_handler()
- Drop HP Stream x360 Convertible PC 11 from allow-list
- Support for tablet mode on Dell Inspiron 7352
intel_mid_powerbtn:
- Remove driver for deprecated platform
- Remove driver for deprecated platform
intel_mid_thermal:
- Remove driver for deprecated platform
- Remove driver for deprecated platform
intel_pmt:
- Make INTEL_PMT_CLASS non-user-selectable
intel_pmt_crashlog:
- Add dependency on MFD_INTEL_PMT
intel_pmt_telemetry:
- Add dependency on MFD_INTEL_PMT
intel_scu_ipc:
- Increase virtual timeout from 3 to 5 seconds
intel_scu_wdt:
- Drop mistakenly added const
- Get rid of custom x86 model comparison
- Drop SCU notification
- Move driver from arch/x86
msi-wmi:
- Fix variable 'status' set but not used compiler warning
platform/surface:
- aggregator: Fix access of unaligned value
- Add Surface Hot-Plug driver
- surface3-wmi: Fix variable 'status' set but not used compiler warning
- aggregator: Fix braces in if condition with unlikely() macro
- aggregator: Fix kernel-doc references
- aggregator: fix a kernel-doc markup
- aggregator_cdev: Add comments regarding unchecked allocation size
- aggregator_cdev: Fix access of uninitialized variables
- fix potential integer overflow on shift of a int
- Add Surface ACPI Notify driver
- Add Surface Aggregator user-space interface
- aggregator: Add dedicated bus and device type
- aggregator: Add error injection capabilities
- aggregator: Add trace points
- aggregator: Add event item allocation caching
- aggregator: Add control packet allocation caching
- Add Surface Aggregator subsystem
- SURFACE_PLATFORMS should depend on ACPI
- surface_gpe: Fix non-PM_SLEEP build warnings
platform/x86/intel-uncore-freq:
- Add Sapphire Rapids server support
rtc:
- mrst: Remove driver for deprecated platform
sony-laptop:
- Remove unneeded semicolon
thinkpad_acpi:
- Replace ifdef CONFIG_ACPI_PLATFORM_PROFILE with depends on
- Fix 'warning: no previous prototype for' warnings
- Add platform profile support
- fixed warning and incorporated review comments
- rectify length of title underline
- Don't register keyboard_lang unnecessarily
- set keyboard language
- Add P53/73 firmware to fan_quirk_table for dual fan control
- correct palmsensor error checking
tools/power/x86/intel-speed-select:
- Update version to 1.8
- Add new command to get/set TRL
- Add new command turbo-mode
- Set higher of cpuinfo_max_freq or base_frequency
- Set scaling_max_freq to base_frequency
touchscreen_dmi:
- Add info for the Jumper EZpad 7 tablet
- Add swap-x-y quirk for Goodix touchscreen on Estar Beauty HD tablet
watchdog:
- intel-mid_wdt: Postpone IRQ handler registration till SCU is ready
- intel_scu_watchdog: Remove driver for deprecated platform
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEEuvA7XScYQRpenhd+kuxHeUQDJ9wFAmAqZ5cUHGhkZWdvZWRl
QHJlZGhhdC5jb20ACgkQkuxHeUQDJ9zmuwf/XLoZzs6oW7Ps9DhkyU5lk7D79rti
DY4AabVnWZhJ+Yl5+qMCTjC0R0nJYoq9PCDU5q20HHSFq7PXV0fPEVo7ZOp8tPng
wdzb2glbtGjSWksjj3c8eB/jjPP0tpsWptH+9jlTv9yXwQNVh/rPVltmD+z8y69U
qNzySltQMtoKmQKNbktUeHA12jBldnH+QlkL8KUp5ZEVDd7gukkmAovpzEcnwk5U
lrza7I52c9Ggu1pD2OCX7an9tk6N7mQ6Rk2/c6GzRsOYa6SC5Aj7fi2bs0LRdGGx
Kz/gtKS3dRIreEs4LGmL8byVi7a/YvCQoTfO+MxKq/btedBwxO2edDDsRg==
=B+Fz
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v5.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver updates from Hans de Goede:
"Highlights:
- Microsoft Surface devices System Aggregator Module support
- SW_TABLET_MODE reporting improvements
- thinkpad_acpi keyboard language setting support
- platform / DPTF profile settings support:
- Base / userspace API parts merged from Rafael's acpi-platform
branch
- thinkpad_acpi and ideapad-laptop support through pdx86
- Remove support for some obsolete Intel MID platforms through
merging of the shared intel-mid-removal branch
- Big cleanup of the ideapad-laptop driver
- Misc other fixes / new hw support / quirks"
* tag 'platform-drivers-x86-v5.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (99 commits)
platform/x86: intel_scu_ipc: Increase virtual timeout from 3 to 5 seconds
platform/surface: aggregator: Fix access of unaligned value
tools/power/x86/intel-speed-select: Update version to 1.8
tools/power/x86/intel-speed-select: Add new command to get/set TRL
tools/power/x86/intel-speed-select: Add new command turbo-mode
Platform: OLPC: Constify static struct regulator_ops
platform/surface: Add Surface Hot-Plug driver
platform/x86: intel_scu_wdt: Drop mistakenly added const
platform/x86: Kconfig: add missing selects for ideapad-laptop
platform/x86: acer-wmi: Don't use ACPI_EXCEPTION()
platform/x86: thinkpad_acpi: Replace ifdef CONFIG_ACPI_PLATFORM_PROFILE with depends on
platform/x86: thinkpad_acpi: Fix 'warning: no previous prototype for' warnings
platform/x86: msi-wmi: Fix variable 'status' set but not used compiler warning
platform/surface: surface3-wmi: Fix variable 'status' set but not used compiler warning
platform/x86: Move all dell drivers to their own subdirectory
Documentation/ABI: sysfs-platform-ideapad-laptop: conservation_mode attribute
Documentation/ABI: sysfs-platform-ideapad-laptop: update device attribute paths
platform/x86: ideapad-laptop: add "always on USB charging" control support
platform/x86: ideapad-laptop: add keyboard backlight control support
platform/x86: ideapad-laptop: send notification about touchpad state change to sysfs
...
-----BEGIN PGP SIGNATURE-----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=/wKL
-----END PGP SIGNATURE-----
Merge tag 'media/v5.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- some core fixes in VB2 mem2mem support
- some improvements and cleanups in V4L2 async kAPI
- newer controls in V4L2 API for H-264 and HEVC codecs
- allegro-dvt driver was promoted from staging
- new i2c sendor drivers: imx334, ov5648, ov8865
- new automobile camera module: rdacm21
- ipu3 cio2 driver started gained support for some ACPI BIOSes
- new ATSC frontend: MaxLinear mxl692 VSB tuner/demod
- the SMIA/CCS driver gained more support for CSS standard
- several driver fixes, updates and improvements
* tag 'media/v5.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (362 commits)
media: v4l: async: Fix kerneldoc documentation for async functions
media: i2c: max9271: Add MODULE_* macros
media: i2c: Kconfig: Make MAX9271 a module
media: imx334: 'ret' is uninitialized, should have been PTR_ERR()
media: i2c: Add imx334 camera sensor driver
media: dt-bindings: media: Add bindings for imx334
media: ov8856: Configure sensor for GRBG Bayer for all modes
media: i2c: imx219: Implement V4L2_CID_LINK_FREQ control
media: ov5675: fix vflip/hflip control
media: ipu3-cio2: Build bridge only if ACPI is enabled
media: Remove the legacy v4l2-clk API
media: ov6650: Use the generic clock framework
media: mt9m111: Use the generic clock framework
media: ov9640: Use the generic clock framework
media: pxa_camera: Drop the v4l2-clk clock register
media: mach-pxa: Register the camera sensor fixed-rate clock
media: i2c: imx258: get clock from device properties and enable it via runtime PM
media: i2c: imx258: simplify getting state container
media: i2c: imx258: add support for binding via device tree
media: dt-bindings: media: imx258: add bindings for IMX258 sensor
...
Add a straightforward IOCTL that provides a mechanism for userspace to
query the supported memory device commands. CXL commands as they appear
to userspace are described as part of the UAPI kerneldoc. The command
list returned via this IOCTL will contain the full set of commands that
the driver supports, however, some of those commands may not be
available for use by userspace.
Memory device commands first appear in the CXL 2.0 specification. They
are submitted through a mailbox mechanism specified in the CXL 2.0
specification.
The send command allows userspace to issue mailbox commands directly to
the hardware. The list of available commands to send are the output of
the query command. The driver verifies basic properties of the command
and possibly inspect the input (or output) payload to determine whether
or not the command is allowed (or might taint the kernel).
Reported-by: kernel test robot <lkp@intel.com> # bug in earlier revision
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com> (v2)
Cc: Al Viro <viro@zeniv.linux.org.uk>
Link: https://lore.kernel.org/r/20210217040958.1354670-5-ben.widawsky@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The VM management interfaces expose several VM operations to ACRN
userspace via ioctls. For example, creating VM, starting VM, destroying
VM and so on.
The ACRN Hypervisor needs to exchange data with the ACRN userspace
during the VM operations. HSM provides VM operation ioctls to the ACRN
userspace and communicates with the ACRN Hypervisor for VM operations
via hypercalls.
HSM maintains a list of User VM. Each User VM will be bound to an
existing file descriptor of /dev/acrn_hsm. The User VM will be
destroyed when the file descriptor is closed.
Cc: Zhi Wang <zhi.a.wang@intel.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: Yu Wang <yu1.wang@intel.com>
Cc: Reinette Chatre <reinette.chatre@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Zhi Wang <zhi.a.wang@intel.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Shuo Liu <shuo.a.liu@intel.com>
Link: https://lore.kernel.org/r/20210207031040.49576-7-shuo.a.liu@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
YUV 4:4:4 is not subsampled, fix this in the docs.
Fixes: da785536e0 ("media: doc: pixfmt-yuv: Move all semi-planar YUV formats to common file")
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Adding userspace support for the MC (Management Complex) means exporting
an ioctl capable device file representing the root resource container.
This new functionality in the fsl-mc bus driver intends to provide
userspace applications an interface to interact with the MC firmware.
Commands that are composed in userspace are sent to the MC firmware
through the FSL_MC_SEND_MC_COMMAND ioctl. By default the implicit MC
I/O portal is used for this operation, but if the implicit one is busy,
a dynamic portal is allocated and then freed upon execution.
The command received through the ioctl interface is checked against a
known whitelist of accepted MC commands. Commands that attempt a change
in hardware configuration will need CAP_NET_ADMIN, while commands used
in debugging do not need it.
Acked-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/20210114170752.2927915-4-ciorneiioana@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The gdth driver refers to a SCSI parallel, PCI-only HBA RAID adapter which
was manufactured by the now-defunct ICP Vortex company, later acquired by
Adaptec and superseded by the aacraid series of controllers. The driver
itself would require a major overhaul before any modifications can be
attempted, but seeing that it's unlikely to have any users left it should
rather be removed completely.
Link: https://lore.kernel.org/r/20210113090500.129644-2-hare@suse.de
Cautiously-Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This control indicates the priority id to be applied
to base layer.
[hverkuil: renumbered V4L2_CID_MPEG_VIDEO_BASELAYER_PRIORITY_ID]
Signed-off-by: Dikshita Agarwal <dikshita@codeaurora.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Adds bitrate control for all coding layers for h264
same as hevc.
Signed-off-by: Dikshita Agarwal <dikshita@codeaurora.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
- Adds min/max qp controls for B frame for h264.
- Adds min/max qp controls for I/P/B frames for hevc similar to h264.
- Update valid range of min/max qp for hevc to accommodate 10 bit.
Signed-off-by: Dikshita Agarwal <dikshita@codeaurora.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add V4L2 controls for controlling CCS lens shading correction as well as
conveying its capabilities.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add two new controls for alternative analogue gain some CCS compliant
camera sensors support.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add V4L2 controls for analogue gain constants required to control
analogue gain. The values are device specific and thus need to be obtained
from the driver.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add user documentation for the CCS driver. This includes e.g. sub-devices
implemented by the driver.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add and document a media entity type for Image Signal Processor devices.
Surprisingly we didn't have one, so add one now. More or less all ISP
drivers should use this type instead of what they currently are using (or
not using anything).
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add a misc-device providing user-space access to the Surface Aggregator
EC, mainly intended for debugging, testing, and reverse-engineering.
This interface gives user-space applications the ability to send
requests to the EC and receive the corresponding responses.
The device-file is managed by a pseudo platform-device and corresponding
driver to avoid dependence on the dedicated bus, allowing it to be
loaded in a minimal configuration.
A python library and scripts to access this device can be found at [1].
[1]: https://github.com/linux-surface/surface-aggregator-module/tree/master/scripts/ssam
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/20201221183959.1186143-9-luzmaximilian@gmail.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
On modern systems the platform performance, temperature, fan and other
hardware related characteristics are often dynamically configurable. The
profile is often automatically adjusted to the load by some
automatic-mechanism (which may very well live outside the kernel).
These auto platform-adjustment mechanisms often can be configured with
one of several 'platform-profiles', with either a bias towards low-power
consumption or towards performance (and higher power consumption and
thermals).
Introduce a new platform_profile sysfs API which offers a generic API for
selecting the performance-profile of these automatic-mechanisms.
Co-developed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Pearson <markpearson@lenovo.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
applications to populate protected regions of user code and data called
enclaves. Once activated, the new hardware protects enclave code and
data from outside access and modification.
Enclaves provide a place to store secrets and process data with those
secrets. SGX has been used, for example, to decrypt video without
exposing the decryption keys to nosy debuggers that might be used to
subvert DRM. Software has generally been rewritten specifically to
run in enclaves, but there are also projects that try to run limited
unmodified software in enclaves."
Most of the functionality is concentrated into arch/x86/kernel/cpu/sgx/
except the addition of a new mprotect() hook to control enclave page
permissions and support for vDSO exceptions fixup which will is used by
SGX enclaves.
All this work by Sean Christopherson, Jarkko Sakkinen and many others.
-----BEGIN PGP SIGNATURE-----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=k7tj
-----END PGP SIGNATURE-----
Merge tag 'x86_sgx_for_v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 SGC support from Borislav Petkov:
"Intel Software Guard eXtensions enablement. This has been long in the
making, we were one revision number short of 42. :)
Intel SGX is new hardware functionality that can be used by
applications to populate protected regions of user code and data
called enclaves. Once activated, the new hardware protects enclave
code and data from outside access and modification.
Enclaves provide a place to store secrets and process data with those
secrets. SGX has been used, for example, to decrypt video without
exposing the decryption keys to nosy debuggers that might be used to
subvert DRM. Software has generally been rewritten specifically to run
in enclaves, but there are also projects that try to run limited
unmodified software in enclaves.
Most of the functionality is concentrated into arch/x86/kernel/cpu/sgx/
except the addition of a new mprotect() hook to control enclave page
permissions and support for vDSO exceptions fixup which will is used
by SGX enclaves.
All this work by Sean Christopherson, Jarkko Sakkinen and many others"
* tag 'x86_sgx_for_v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (30 commits)
x86/sgx: Return -EINVAL on a zero length buffer in sgx_ioc_enclave_add_pages()
x86/sgx: Fix a typo in kernel-doc markup
x86/sgx: Fix sgx_ioc_enclave_provision() kernel-doc comment
x86/sgx: Return -ERESTARTSYS in sgx_ioc_enclave_add_pages()
selftests/sgx: Use a statically generated 3072-bit RSA key
x86/sgx: Clarify 'laundry_list' locking
x86/sgx: Update MAINTAINERS
Documentation/x86: Document SGX kernel architecture
x86/sgx: Add ptrace() support for the SGX driver
x86/sgx: Add a page reclaimer
selftests/x86: Add a selftest for SGX
x86/vdso: Implement a vDSO for Intel SGX enclave call
x86/traps: Attempt to fixup exceptions in vDSO before signaling
x86/fault: Add a helper function to sanitize error code
x86/vdso: Add support for exception fixup in vDSO functions
x86/sgx: Add SGX_IOC_ENCLAVE_PROVISION
x86/sgx: Add SGX_IOC_ENCLAVE_INIT
x86/sgx: Add SGX_IOC_ENCLAVE_ADD_PAGES
x86/sgx: Add SGX_IOC_ENCLAVE_CREATE
x86/sgx: Add an SGX misc driver interface
...
Planar pixel formats are documented in separate files. This duplicates
information, as those formats share comon traits. Consolidate them in a
single file and summarize their descriptions in a single table.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Semi-planar pixel formats are documented in separate files. This
duplicates information, as those formats share comon traits. Consolidate
them in a single file and summarize their descriptions in a single
table.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Luma-only pixel formats are documented in separate files. This
duplicates information, as those formats share comon traits. Consolidate
them in a single file and describe them in a single table.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Document the naming scheme for the existing packed YUV 4:4:4 formats, as
previously done for the RGB formats.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The 4:4:4 packed YUV formats are documented with a bit-level
representation, which creates a wide table. Switch to a byte-oriented
representation to make it more compact. This prepares for the addition
of formats with more than 8 bits per component, that would make the
table way too wide.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The padding bits are left blank, which look weird in the XYUV format,
and, worse, may lead to the VUYX format to be understand as consuming 3
bytes per pixel. Add 'X' for padding bits as we do for RGB formats.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pixfmt-packed-yuv.rst file documents packed YUV 4:4:4 formats, but
is titled generically as "Packed YUV formats". 4:2:2 and 4:1:1 packed
YUV formats are documented in separate files, which can be confusing.
Group all packed YUV formats in pixfmt-packed-yuv.rst, which allows
documenting the 4:2:2 formats in a more concise way.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Document YUV subsampling, including chroma spatial siting, and replace
the siting examples in individual formats by references to the common
documentation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Using '-' to represent padding bits and bytes make text and tables more
difficult to read. Use 'x' and 'X' instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
All formats using 8 bits per component can be described with a byte
granularity instead of a bit granularity without loss of precision. This
makes the corresponding table more compact and easier to read.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The naming scheme for the RGB pixel formats has been developed
organically, and isn't consistent between formats using less than 8 bits
per pixels (mostly stored in 1 or 2 bytes per pixel, except for RGB666
that uses 4 bytes per pixel) and formats with 8 bits per pixel (stored
in 3 or 4 bytes). For the latter category, the names use a components
order convention that is the opposite of the first category, and the
opposite of DRM pixel formats. This has led to lots of confusion in the
past, and would really benefit from being explained more precisely. Do
so, which also prepares for the addition of additional RGB pixels
formats.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Improve readability of the documentation by adding a section title for
the deprecated formats.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The packed RGB formats documentation includes a layout table without any
context. This doesn't bring much useful information, and is confusing at
best. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
With Sphinx 2.x: those two warnings are produced:
/devel/v4l/docs/sphinx2/Documentation/output/videodev2.h.rst:6: WARNING: undefined label: v4l2-meta-fmt-rk-isp1-params (if the link has no caption the label must precede a section header)
/devel/v4l/docs/sphinx2/Documentation/output/videodev2.h.rst:6: WARNING: undefined label: v4l2-meta-fmt-rk-isp1-stat-3a (if the link has no caption the label must precede a section header)
The reason is that there's no blank line between the two
identifiers.
Fixes: 3f46cac678 ("media: admin-guide/pixfmt-meta-rkisp1.rst: pixfmt reference conforming with macro")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Document V4L2_CTRL_TYPE_FWHT_PARAMS and p_fwht_params. Also
improve the V4L2_PIX_FMT_FWHT_STATELESS description.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add 'struct' to clarify that these are pointers to structs.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Drop the 'bullets' for the HEVC stateless codec documentation.
It doesn't work, and they just show up as asterisks.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Move the documentation for the stateless FWHT codec to
ext-ctrls-codec-stateless.rst since that is the proper place
for the stable stateless API documentation.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The FWHT stateless 'uAPI' was staging and marked explicitly in the
V4L2 specification that it will change and is unstable.
Note that these control IDs were never exported as a public API,
they were only defined at the driver's code.
While not too late, let's rename them is preparation for promoting
the stateless FWHT codec API as a public API.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The v4l2_area struct was not documented in the media documentation,
which meant that references to that struct elsewhere in the documentation
never linked to anything.
[mchehab: remove .. cssclass:: longtable]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix warnings from make htmlddocs:
Documentation/output/videodev2.h.rst:6: WARNING: undefined label: v4l2-meta-fmt-rk-isp1-params (if the link has no caption the label must precede a section header)
Documentation/output/videodev2.h.rst:6: WARNING: undefined label: v4l2-meta-fmt-rk-isp1-stat-3a (if the link has no caption the label must precede a section header)
Fixes: df22026aeb ("media: videodev2.h, v4l2-ioctl: add rkisp1 meta buffer format")
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Now that we've destaged the H264 stateless codec controls,
and with all the pieces in place, update the documentation
and move it to its own section.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When V4L2_CTRL_TYPE_H264_PRED_WEIGHTS was added, adding a replace
symbol directive in videodev2.h.rst.exceptions was missed.
Now that the control type is destaged, it's important to fix this.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add a new control class to hold the stateless codecs controls
that are ready to be moved out of staging.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
For historical reasons, stateful codec controls are named
as {}_MPEG_{}. While we can't at this point sanely
change all control IDs (such as V4L2_CID_MPEG_VIDEO_VP8_FRAME_HEADER),
we can least change the more meaningful macros such as classes
macros.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
V4L2_CTRL_CLASS_DETECT was never documented here, add it.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl/EM9oeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG/3kH/RNkFyTlHlUkZpJx
8Ks2yWgUln7YhZcmOaG/IcIyWnhCgo3l35kiaH7XxM+rPMZzidp51MHUllaTAQDc
u+5EFHMJsmTWUfE8ocHPb1cPdYEDSoVr6QUsixbL9+uADpRz+VZVtWMb89EiyMrC
wvLIzpnqY5UNriWWBxD0hrmSsT4g9XCsauer4k2KB+zvebwg6vFOMCFLFc2qz7fb
ABsrPFqLZOMp+16chGxyHP7LJ6ygI/Hwf7tPW8ppv4c+hes4HZg7yqJxXhV02QbJ
s10s6BTcEWMqKg/T6L/VoScsMHWUcNdvrr3uuPQhgup240XdmB1XO8rOKddw27e7
VIjrjNw=
=4ZaP
-----END PGP SIGNATURE-----
Merge tag 'v5.10-rc6' into patchwork
Linux 5.10-rc6
* tag 'v5.10-rc6': (1815 commits)
Linux 5.10-rc6
sock: set sk_err to ee_errno on dequeue from errq
mptcp: fix NULL ptr dereference on bad MPJ
net: openvswitch: fix TTL decrement action netlink message format
perf probe: Change function definition check due to broken DWARF
perf probe: Fix to die_entrypc() returns error correctly
perf stat: Use proper cpu for shadow stats
perf record: Synthesize cgroup events only if needed
perf diff: Fix error return value in __cmd_diff()
perf tools: Update copy of libbpf's hashmap.c
x86/mce: Do not overwrite no_way_out if mce_end() fails
kvm: x86/mmu: Fix get_mmio_spte() on CPUs supporting 5-level PT
KVM: x86: Fix split-irqchip vs interrupt injection window request
KVM: x86: handle !lapic_in_kernel case in kvm_cpu_*_extint
usb: typec: stusb160x: fix power-opmode property with typec-power-opmode
printk: finalize records with trailing newlines
can: af_can: can_rx_unregister(): remove WARN() statement from list operation sanity check
can: m_can: m_can_dev_setup(): add support for bosch mcan version 3.3.0
can: m_can: fix nominal bitiming tseg2 min for version >= 3.1
can: m_can: m_can_open(): remove IRQF_TRIGGER_FALLING from request_threaded_irq()'s flags
...
Drop the doubled word "and".
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-doc@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Drop the doubled word "and".
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-doc@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Drop the doubled word "Any".
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-doc@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Drop the doubled word "in".
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-doc@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Drop the doubled word "controls".
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-doc@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Drop the doubled word "standard.".
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-doc@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Drop the doubled word "the".
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-doc@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Drop the doubled word "and".
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-doc@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Drop the doubled word "the".
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-doc@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Drop the doubled word "and".
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-doc@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Drop the doubled word "and".
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-doc@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The rc_proto enum values should be ignored for now, otherwise we get
warnings like:
Documentation/output/lirc.h.rst:6: WARNING: undefined label: rc-proto-max (if the link has no caption the label must precede a section header)
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes: 72e637fec5 ("media: rc: validate that "rc_proto" is reasonable")
Fixes: cea357bc25 ("media: lirc: ensure RC_PROTO_MAX has documentation")
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Pali Rohár