This patch detects DSI presence for ICL platform
by reading VBT. DSI detection is done while initializing
DSI using newly added function intel_gen11_dsi_init.
v2 by Jani:
- Preserve old behavour of intel_bios_is_dsi_present()
- s/intel_gen11_dsi_init/icl_dsi_init/g
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/2324cdfc8918bda3165354e5e0d15053b1074f14.1540900289.git.jani.nikula@intel.com
Program the timeout values (in escape clock) for HS TX, LP RX and TA
timeout.
HX TX: Ensure that host does not continuously transmit in the HS
state. If this timer expires, then host will gracefully end its HS
transmission and allow the link to enter into LP state.
LP RX: Monitor the length of LP receptions from Peripheral. If timeout
happens then host will drive the stop state onto all data lanes (only
Data Lane 0 should be receiving anything from the Peripheral). This
effectively takes back ownership of the bus transmit in the HS state.
TA timeout: Timeout valuefor monitoring Bus Turn-Around (BTA) sequence.
BTA sequence should complete within a bounded amount of time, with
peripheral acknowledging BTA by driving the stop state.
v2 by Jani:
- Rebase
- Use intel_dsi_bitrate() and intel_dsi_tlpx_ns(intel_dsi)
- Squash HX TX, LP RX and TA timeout into one patch
- Fix bspec mode set sequence reference
- Add FIXME about two timeouts
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/60e610ccffe5f8c09dee1c65828f28f25227efce.1540900289.git.jani.nikula@intel.com
This patch sends command and executes display off,
assert reset, power off VBT seqeuences to power
down DSI panel. Patch also adds high level function
to wrap all the panel sepcific programming during
DSI disabling.
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/efdafbf6b4d31123738b87b2d8264a9b5553eb32.1540900289.git.jani.nikula@intel.com
Driver needs payload/header credits for sending any command
and data over DSI link. These credits are released once command
or data sent to link. This patch adds functions to wait for releasing
of payload and header credits.
As per BSPEC, driver needs to ensure that all of commands/data
has been dispatched to panel before the transcoder is enabled.
This patch implement those steps i.e. sending NOP DCS command,
wait for header/payload credit to be released etc.
v2 by Jani:
- squash the credit wait helpers patch with the first user
- pass dev_priv to the credit wait helpers
- bikeshed credit helper names
- wait for *at least* the current maximum number of credits
- indentation fix
- add helpers for credits available
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/84bc509beabf2a2d1324a9f2a67ab4ebe05b10a6.1540900289.git.jani.nikula@intel.com
As part of DSI enable sequence, transcoder timings
(horizontal & vertical) need to be set so that transcoder
will generate the stream output as per those timings.
This patch set required transcoder timings as per BSPEC.
v2: Remove TRANS_TIMING_SHIFT usage
v3 by Jani:
- Rebase
- Reduce temp variable use
- Checkpatch fix
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/525949ae4e919a4f2b807d606234322534656048.1539613303.git.jani.nikula@intel.com
This patch programs DSI operation mode, pixel format,
BGR info, link calibration etc for the DSI transcoder.
This patch also extract BGR info of the DSI panel from
VBT and save it inside struct intel_dsi which used for
configuring DSI transcoder.
v2: Rebase
v3: Use newly defined bitfields.
v4 by Jani:
- Use intel_dsi_bitrate()
- Make bgr_enabled bool
- Use 0 instead of 0x0
- Replace DRM_ERROR() with MISSING_CASE() on pixel format and video mode
- Use is_vid_mode()
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/7de4e39a4b2a18e53a2b9d9cea5b5b4c9d6eeb34.1539613303.git.jani.nikula@intel.com
This patch programs D-PHY timing parameters for the
bus turn around flow(in escape clocks) only if dsi link
frequency <=800 MHz using DPHY_TA_TIMING_PARAM and its
identical register DSI_TA_TIMING_PARAM (inside DSI
Controller within the Display Core).
v2: Changes
- Don't use KHz() macro (Ville/Jani N)
- Use newly defined bitfields
v3 by Jani:
- Use intel_dsi_bitrate() in favor of a new field
- Remove redundant parens
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/2c777092a748dfc973714399d8c19ed7a8c31a10.1539613303.git.jani.nikula@intel.com
This patch programs D-PHY timing parameters for the
clock and data lane (in escape clocks) of DSI
controller (DSI port 0 and 1).
These programmed timings would be used by DSI Controller
to calculate link transition latencies of the data and
clock lanes.
v2: Use newly defined bitfields for data and clock lane
v3 by Jani:
- Rebase on dphy abstraction
- Reduce local variables
- Remove unrelated comment changes (Ville)
- Use the same style for range checks as VLV (Ville)
- Assign, don't OR dphy_reg contents
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/70d491e2357f328a63b67ea3c43cb57a1d469c15.1539613303.git.jani.nikula@intel.com
This patch programs the time (in escape clocks) to drive
the link in the initialization (i.e. LP-11) state.
v2: Rebase
v3: Remove step hard coding comments (Jani N)
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1537095223-5184-5-git-send-email-madhav.chauhan@intel.com
This patch enables DDI buffer by writing to DDI_BUF_CTL
register and wait for DDI status to be *not idle* for a
port.
v2: Rebase
v3: Remove step hard coding comments (Jani N)
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1537095223-5184-4-git-send-email-madhav.chauhan@intel.com
This patch setup voltage swing before enabling
combo PHY DDI (shared with DSI).
Note that DSI voltage swing programming is for
high speed data buffers. HW automatically handles
the voltage swing for the low power data buffers.
v2: Rebase
v3: Address various review comments related to VSWING
programming (Jani N)
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1537095223-5184-3-git-send-email-madhav.chauhan@intel.com
This patch set the loadgen select and latency optimization for
aux and transmit lanes of combo phy transmitters. It will be
used for MIPI DSI HS operations.
v2: Rebase
v3: Add empty line to make code more legible (Ville).
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1537095223-5184-2-git-send-email-madhav.chauhan@intel.com
To save power, unused lanes should be powered
down using the bitfield of PORT_CL_DW10.
v2: Review comments from Jani N
- Put default label next to case 4
- Include the shifts in the macros
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1530798591-2077-7-git-send-email-madhav.chauhan@intel.com
Escape Clock is used for LP communication across the DSI
Link. To achieve the constant frequency of the escape clock
from the variable DPLL frequency output, a variable divider(M)
is needed. This patch programs the same.
v2: (Jani N) Don't end line with "(".
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1530798591-2077-3-git-send-email-madhav.chauhan@intel.com
Madhav Chauhan