On SKL+ the plane WM/BUF_CFG registers are a proper part of each
plane's register set. That means accessing them will cancel any
pending plane update, and we would need a PLANE_SURF register write
to arm the wm/ddb change as well.
To avoid all the problems with that let's just move the wm/ddb
programming into the plane update/disable hooks. Now all plane
registers get written in one (hopefully atomic) operation.
To make that feasible we'll move the plane ddb tracking into
the crtc state. Watermarks were already tracked there.
v2: Rebase due to input CSC
v3: Split out a bunch of junk (Matt)
v4: Add skl_wm_add_affected_planes() to deal with
cursor special case and non-zero wm register reset value
v5: Drop the unrelated for_each_intel_plane_mask() fix (Matt)
Remove the redundant ddb memset() (Matt)
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> #v3
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181127165900.31298-1-ville.syrjala@linux.intel.com
While PSR is active hardware will do aux transactions by it self to
wakeup sink to receive a new frame when necessary. If that
transaction is not acked by sink, hardware will trigger this
interruption.
So let's disable PSR as it is a hint that there is problem with this
sink.
The removed FIXME was asking to manually train the link but we don't
need to do that as by spec sink should do a short pulse when it is
out of sync with source, we just need to make sure it is awaken and
the SDP header with PSR inactive set it will trigger the short pulse
with a error set in the link status.
v3: added workarround to fix scheduled work starvation cause by
to frequent PSR error interruption
v4: only setting irq_aux_error as we don't care in clear it and
not using dev_priv->irq_lock as consequence.
v5: rebased: using edp_psr_shift()
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181121225441.18785-4-jose.souza@intel.com
When we detect a error and disable PSR, it is kept disabled until the
next modeset but as the sink already show signs that it do not
properly work with PSR lets disabled it for good to avoid any
additional flickering.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181121225441.18785-3-jose.souza@intel.com
VBT appears to have two (or possibly three) ways to indicate the panel
rotation. The first is in the MIPI config block, but that apparenly
usually (maybe always?) indicates 0 degrees despite the actual panel
orientation. The second way to indicate this is in the general features
block, which can just indicate whether 180 degress rotation is used.
The third might be a separate rotation data block, but that is not
at all documented so who knows what it may contain.
Let's try the first two. We first try the DSI specicic VBT
information, and it it doesn't look trustworthy (ie. indicates
0 degrees) we fall back to the 180 degree thing. Just to avoid too
many changes in one go we shall also keep the hardware readout path
for now.
If this works for more than just my VLV FFRD the question becomes
how many of the panel orientation quirks are now redundant?
v2: Move the code into intel_dsi.c (Jani)
Cc: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181022142015.4026-1-ville.syrjala@linux.intel.com
Tested-by: Hans de Goede <hdegoede@redhat.com>
This reduces the size of struct skl_wm_level from 6 to 4, which
reduces the size of struct skl_plane_wm from 104 to 70, which reduces
the size of struct skl_pipe_wm from 524 to 356. A reduction of 168
padding bytes per pipe. This will increase even more the next time we
bump I915_MAX_PLANES.
v2: Paste the pahole output provided by Lucas:
$ pahole -s -C skl_wm_level drivers/gpu/drm/i915/i915.o
struct skl_wm_level {
bool plane_en; /* 0 1 */
/* XXX 1 byte hole, try to pack */
uint16_t plane_res_b; /* 2 2 */
uint8_t plane_res_l; /* 4 1 */
/* size: 6, cachelines: 1, members: 3 */
/* sum members: 4, holes: 1, sum holes: 1 */
/* padding: 1 */
/* last cacheline: 6 bytes */
};
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181016220133.26991-3-paulo.r.zanoni@intel.com
Similarly to the GEN9_LP DPIO PHY code keep the CNL+ combo PHY code in a
separate file.
No functional change.
v2:
- Use SPDX license tag instead of boilerplate. (Rodrigo)
v3:
- Use MIT instead of GPL-2.0 license. (Ville)
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181106160621.23057-3-imre.deak@intel.com
Unfortunately, it seems that the HPD IRQ storm problem from the early
days of Intel GPUs was never entirely solved, only mostly. Within the
last couple of days, I got a bug report from one of our customers who
had been having issues with their machine suddenly booting up very
slowly after having updated. The amount of time it took to boot went
from around 30 seconds, to over 6 minutes consistently.
After some investigation, I discovered that i915 was reporting massive
amounts of short HPD IRQ spam on this system from the DisplayPort port,
despite there not being anything actually connected. The symptoms would
start with one "long" HPD IRQ being detected at boot:
[ 1.891398] [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00440000, dig 0x00440000, pins 0x000000a0
[ 1.891436] [drm:intel_hpd_irq_handler [i915]] digital hpd port B - long
[ 1.891472] [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 5 - cnt: 0
[ 1.891508] [drm:intel_hpd_irq_handler [i915]] digital hpd port D - long
[ 1.891544] [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 7 - cnt: 0
[ 1.891592] [drm:intel_dp_hpd_pulse [i915]] got hpd irq on port B - long
[ 1.891628] [drm:intel_dp_hpd_pulse [i915]] got hpd irq on port D - long
…
followed by constant short IRQs afterwards:
[ 1.895091] [drm:intel_encoder_hotplug [i915]] [CONNECTOR:66:DP-1] status updated from unknown to disconnected
[ 1.895129] [drm:i915_hotplug_work_func [i915]] Connector DP-3 (pin 7) received hotplug event.
[ 1.895165] [drm:intel_dp_detect [i915]] [CONNECTOR:72:DP-3]
[ 1.895275] [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00200000, dig 0x00200000, pins 0x00000080
[ 1.895312] [drm:intel_hpd_irq_handler [i915]] digital hpd port D - short
[ 1.895762] [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00200000, dig 0x00200000, pins 0x00000080
[ 1.895799] [drm:intel_hpd_irq_handler [i915]] digital hpd port D - short
[ 1.896239] [drm:intel_dp_aux_xfer [i915]] dp_aux_ch timeout status 0x71450085
[ 1.896293] [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00200000, dig 0x00200000, pins 0x00000080
[ 1.896330] [drm:intel_hpd_irq_handler [i915]] digital hpd port D - short
[ 1.896781] [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00200000, dig 0x00200000, pins 0x00000080
[ 1.896817] [drm:intel_hpd_irq_handler [i915]] digital hpd port D - short
[ 1.897275] [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00200000, dig 0x00200000, pins 0x00000080
The customer's system in question has a GM45 GPU, which is apparently
well known for hotplugging storms.
So, workaround this impressively broken hardware by changing the default
HPD storm threshold from 5 to 50. Then, make long IRQs count for 10, and
short IRQs count for 1. This makes it so that 5 long IRQs will trigger
an HPD storm, and on systems with short HPD storm detection 50 short
IRQs will trigger an HPD storm. 50 short IRQs amounts to 100ms of
constant pulsing, which seems like a good middleground between being too
sensitive and not being sensitive enough (which would cause visible
stutters in userspace every time a storm occurs).
And just to be extra safe: we don't enable this by default on systems
with MST support. There's too high of a chance of MST support triggering
storm detection, and systems that are new enough to support MST are a
lot less likely to have issues with IRQ storms anyway.
As a note: this patch was tested using a ThinkPad T450s and a Chamelium
to simulate the short IRQ storms.
Changes since v1:
- Don't use two separate thresholds, just make long IRQs count for 10
each and short IRQs count for 1. This simplifies the code a bit
- Ville Syrjälä
Changes since v2:
- Document @long_hpd in intel_hpd_irq_storm_detect, no functional
changes
Changes since v4:
- Remove !! in long_hpd assignment - Ville Syrjälä
- queue_hp = true - Ville Syrjälä
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181106213017.14563-6-lyude@redhat.com
Most of the AUX_CH_CTL flags are concerned with DP AUX transfer
parameters. As opposed to this the flag specifying the thunderbolt vs.
non-thunderbolt mode of the port is not related to AUX transfers at all
(rather it's repurposed to enable either TBT or non-TBT PHY HW blocks).
The programming has to be done before enabling the corresponding AUX
power well, so make it part of the power well code.
v3:
- Use existing enable/disable helpers instead of opencoding. (Jose)
- Fix type of is_tc_tbt to remain a bitfield. (Lucas)
- Add comment describing the is_tc_tbt power well flag. (Lucas)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108548
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101140427.31026-8-imre.deak@intel.com
From ICL onwards all the DDI/TypeC ports - even working in HDMI mode -
need to know their corresponding AUX channel, so move the corresponding
helper to a common place.
No functional change.
v4:
- Fix 'no space is necessary after a cast' checkpatch warn.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101140427.31026-2-imre.deak@intel.com
commit ac657f6461 ("drm/i915: Introduce IS_GEN macro") introduced
GEN_FOREVER that was never used.
My first attempt was to rename it to FOREVER since GEN is
already part of the macro. Then I used coccinelle to change all
-INTEL_GEN(e1) >= e2
+INTEL_GEN_RANGE(e1, e2, FOREVER)
-INTEL_GEN(e1) <= e2
+INTEL_GEN_RANGE(e1, 0, e2)
and I liked it.
However I didn't like very much the remaining
INTEL_GEN(dev_priv) < n
and:
INTEL_GEN(e1) < n
INTEL_GEN_RANGE(e1, 0, n - 1)
didn't make much sense either.
So INTEL_GEN use for > or < seems a better unified way for unlimited
bounds. So, no reason to keep GEN_FOREVER here.
Let's kill before someone start using it.
v2: Remove remaining GEN_FOREVER forgotten in a comment. (Daniel)
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181026195143.20353-2-rodrigo.vivi@intel.com
The 16Gb DIMM w/a is not applicable to BXT or GLK. Limit it to
the appropriate platforms.
This was especially harsh on GLK since we don't even try to read
the DIMM information on that platforms, hence valid_dimm was
always false and thus we always tried to apply the w/a.
Furthermore the w/a pushed the level 0 latency above the
level 1 latency, which doesn't really make sense.
v2: Do the check when populating is_16gb_dimm (Mahesh)
Cc: Mahesh Kumar <mahesh1.kumar@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: 86b592876c ("drm/i915: Implement 16GB dimm wa for latency level-0")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181023182102.31549-1-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Mahesh Kumar <mahesh1.sh.kumar@gmail.com>
The way our hardware is designed doesn't seem to let us use the
MI_RECORD_PERF_COUNT command without setting up a circular buffer.
In the case where the user didn't request OA reports to be available
through the i915 perf stream, we can set the OA buffer to the minimum
size to avoid consuming memory which won't be used by the driver.
v2: Simplify oa buffer size exponent selection (Chris)
Reuse vma size field (Lionel)
v3: Restrict size opening parameter to values supported by HW (Chris)
v4: Drop out of date comment (Matt)
Add debug message when buffer size is rejected (Matt)
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181023100707.31738-5-lionel.g.landwerlin@intel.com
We initialize the OA buffer everytime we enable the OA unit (first call in
gen[78]_oa_enable), so we don't need to initialize when preparing the metric
set.
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181023100707.31738-3-lionel.g.landwerlin@intel.com
Now that we have intel_connector.c, move the connector specific
functions from intel_display.c there. Fix a few checkpatch complaints
while at it. No functional changes.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181010075205.7713-2-jani.nikula@intel.com
ALPM is a requirement and we don't need to keep it's cached, what
were done in commit 97c9de66ca
("drm/i915/psr: Fix ALPM cap check for PSR2") but the alpm was not
removed from i915_psr.
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181003205031.32474-7-jose.souza@intel.com
According to patch "drm/i915/aml: Introducing Amber Lake platform"
(e364672477). Add a new marco for AML ULX GT2 devices.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jose Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lee, Shawn C <shawn.c.lee@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1538034499-31256-1-git-send-email-shawn.c.lee@intel.com
Add plane alpha blending support with the different blend modes.
This has been tested on a icl to show the correct results,
on earlier platforms small rounding errors cause issues. But this
already happens case with fully transparant or fully opaque RGB8888
fb's.
The recommended HW workaround is to disable alpha blending when the
plane alpha is 0 (transparant, hide plane) or 0xff (opaque, disable blending).
This is easy to implement on any platform, so just do that.
The tests for userspace are also available, and pass on gen11.
Changes since v1:
- Change mistaken < 0xff0 to 0xff00.
- Only set PLANE_KEYMSK_ALPHA_ENABLE when plane alpha < 0xff00, ignore blend mode.
- Rework disabling FBC when per pixel alpha is used.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
[mlankhorst: Change MISSING_CASE default to explicit alpha disable (mattrope)]
Link: https://patchwork.freedesktop.org/patch/msgid/20180815103405.22679-1-maarten.lankhorst@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
In the next few patches, we will want to give a small priority boost to
some requests/queues but not so much that we perturb the user controlled
order. As such we will shift the user priority bits higher leaving
ourselves a few low priority bits for our internal bumping.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181001123204.23982-3-chris@chris-wilson.co.uk
Now that we are confident in providing full-ppgtt where supported,
remove the ability to override the context isolation.
v2: Remove faked aliasing-ppgtt for testing as it no longer is accepted.
v3: s/USES/HAS/ to match usage and reject attempts to load the module on
old GVT-g setups that do not provide support for full-ppgtt.
v4: Insulate ABI ppGTT values from our internal enum (later plans
involve moving ppGTT depth out of the enum, thus potentially breaking
ABI unless we document the current values).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Acked-by: Zhi Wang <zhi.a.wang@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180926201222.5643-1-chris@chris-wilson.co.uk
Partial views are small but there can be many of them, and since the sg
list space for them is allocated pessimistically, we can save some slab by
trimming the unused tail entries.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180926080353.20867-1-tvrtko.ursulin@linux.intel.com
Move max firmware size to the same if ladder with firmware name and
required version. This allows us to detect the missing max size for a
platform without actually loading the firmware, and makes the whole
thing easier to maintain.
We need to move the power get earlier to allow for early return in the
missing platform case. While at it, extend the comment on why we return
with the reference held on errors.
We also need to move the module parameter override later to reuse the
max firmware size, which is independent of the override.
v2: Add comment on why we leak the wakeref on errors (Chris)
v3: Rebase
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180926133414.22073-2-jani.nikula@intel.com
It really wants dev_priv anyway, also now matches i915_gem_init_stolen.
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180920142707.19659-2-matthew.auld@intel.com
That we use a WB mapping for updating the RING_TAIL register inside the
context image even on !llc machines has been a source of consternation
for every reader. It appears to work on bsw+, but it may just have been
that we have been incredibly bad at detecting the errors.
v2: With extra enthusiasm.
v3: Drop force of map type for pinned default_state as by the time we
pin it, the map type is always WB and doesn't conflict with the earlier
use by ce->state.
v4: Transfer engine->default_state from MAP_WC to MAP_WB on creation so
we do not need the MAP_FORCE littered around the backends
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180914123504.2062-3-chris@chris-wilson.co.uk
UAPI Changes:
- Add host endian variants for the most common formats (Gerd)
- Fail ADDFB2 for big-endian drivers that don't advertise BE quirk (Gerd)
- clear smem_start in fbdev for drm drivers to avoid leaking fb addr (Daniel)
Cross-subsystem Changes:
Core Changes:
- fix drm_mode_addfb() on big endian machines (Gerd)
- add timeline point to syncobj find+replace (Chunming)
- more drmP.h removal effort (Daniel)
- split uapi portions of drm_atomic.c into drm_atomic_uapi.c (Daniel)
Driver Changes:
- bochs: Convert open-coded portions to use helpers (Peter)
- vkms: Add cursor support (Haneen)
- udmabuf: Lots of fixups (mostly cosmetic afaict) (Gerd)
- qxl: Convert to use fbdev helper (Peter)
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Chunming Zhou <david1.zhou@amd.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Peter Wu <peter@lekensteyn.nl>
Cc: Haneen Mohammed <hamohammed.sa@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEfxcpfMSgdnQMs+QqlvcN/ahKBwoFAluaXuAACgkQlvcN/ahK
BwrQHggAtcu96+plN6cDcMcoOfnQT/OG30dBER4/cpG05hEciq/NXwXBQ9dPWtqk
Nkcgst28UbXTmt0UKck7ibfePLVqnN7+yRqnj3yrD28Qjrg1Ewr0go8cKlIJ8+8t
E6aLvgRwx5/9sHHaeCC1K1qfowEr0Put9DQvLH2BVRM3C1Sj5BXeXMP4djb5PHGU
BYGLoN9DrrVHLVARwbmzSb8V5oLED2CdRkL7WpXC2LcEGZ3jPllTN8EOoqsIMOAZ
LGnpWxADVnYTA5np3O0QJsalu942T4rMPoxgCHZmuGIhEijqk7mgGWpeOmzN71Eh
rXX1yyWvZenUc69Pbl7G7lQmE6DSDw==
=9Mxt
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2018-09-13' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 4.20:
UAPI Changes:
- Add host endian variants for the most common formats (Gerd)
- Fail ADDFB2 for big-endian drivers that don't advertise BE quirk (Gerd)
- clear smem_start in fbdev for drm drivers to avoid leaking fb addr (Daniel)
Cross-subsystem Changes:
Core Changes:
- fix drm_mode_addfb() on big endian machines (Gerd)
- add timeline point to syncobj find+replace (Chunming)
- more drmP.h removal effort (Daniel)
- split uapi portions of drm_atomic.c into drm_atomic_uapi.c (Daniel)
Driver Changes:
- bochs: Convert open-coded portions to use helpers (Peter)
- vkms: Add cursor support (Haneen)
- udmabuf: Lots of fixups (mostly cosmetic afaict) (Gerd)
- qxl: Convert to use fbdev helper (Peter)
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Chunming Zhou <david1.zhou@amd.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Peter Wu <peter@lekensteyn.nl>
Cc: Haneen Mohammed <hamohammed.sa@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20180913130254.GA156437@art_vandelay
IPC may cause underflows if not used with dual channel symmetric
memory configuration. Disable IPC for non symmetric configurations in
affected platforms.
Display WA #1141
Changes Since V1:
- Re-arrange the code.
- update wrapper to return if memory is symmetric (Rodrigo)
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180824093225.12598-6-mahesh1.kumar@intel.com
Memory with 16GB dimms require an increase of 1us in level-0 latency.
This patch implements the same.
Bspec: 4381
changes since V1:
- s/memdev_info/dram_info
- make skl_is_16gb_dimm pure function
Changes since V2:
- make is_16gb_dimm more generic
- rebase
Changes since V3:
- Simplify condition (Maarten)
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180831110942.9234-1-mahesh1.kumar@intel.com
This patch adds support to decode system memory bandwidth and other
parameters for skylake and Gen9+ platforms, which will be used for
arbitrated display memory bandwidth calculation in GEN9 based
platforms and WM latency level-0 Work-around calculation on GEN9+.
Changes Since V1:
- s/memdev_info/dram_info
- create a struct to hold channel info
Changes Since V2:
- rewrite code to adhere i915 coding style
- not valid for GLK
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180824093225.12598-3-mahesh1.kumar@intel.com
This patch adds support to decode system memory bandwidth and other
parameters for broxton platform, which will be used for arbitrated
display memory bandwidth calculation in GEN9 based platforms and
WM latency level-0 Work-around calculation on GEN9+ platforms.
Changes since V1:
- s/memdev_info/dram_info
Changes since V2:
- Adhere to i915 coding style (Rodrigo)
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180824093225.12598-2-mahesh1.kumar@intel.com
Use I915_GTT_PAGE_SIZE when talking about GTT pages rather than
physical pages.
There are some PAGE_SHIFTs left though. Not sure if we want to
introduce I915_GTT_PAGE_SHIFT or what?
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk> # at least some of it :)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180913150405.706-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
We have a bunch of neat little macros all over the place which should
move to kernel.h. But some of them died in bikesheds on lkml, and we
need a decent home for them.
Start out by moving the for_each_if macro there.
v2: Rename to drm_util.h instead (Dave&Sean)
Cc: Sean Paul <seanpaul@chromium.org>
Acked-by: Sean Paul <seanpaul@chromium.org>
Cc: Dave Airlie <airlied@gmail.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180905135711.28370-1-daniel.vetter@ffwll.ch
Future gen reduce the number of bits we will have available to
differentiate between contexts, so reduce the lifetime of the ID
assignment from that of the context to its current active cycle (i.e.
only while it is pinned for use by the HW, will it have a constant ID).
This means that instead of a max of 2k allocated contexts (worst case
before fun with bit twiddling), we instead have a limit of 2k in flight
contexts (minus a few that have been pinned by the kernel or by perf).
To reduce the number of contexts id we require, we allocate a context id
on first and mark it as pinned for as long as the GEM context itself is,
that is we keep it pinned it while active on each engine. If we exhaust
our context id space, then we try to reclaim an id from an idle context.
In the extreme case where all context ids are pinned by active contexts,
we force the system to idle in order to recover ids.
We cannot reduce the scope of an HW-ID to an engine (allowing the same
gem_context to have different ids on each engine) as in the future we
will need to preassign an id before we know which engine the
context is being executed on.
v2: Improved commentary (Tvrtko) [I tried at least]
References: https://bugs.freedesktop.org/show_bug.cgi?id=107788
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180904153117.3907-1-chris@chris-wilson.co.uk
Older gen use a physical address for the hardware status page, for which
we use cache-coherent writes. As the writes are into the cpu cache, we use
a normal WB mapped page to read the HWS, used for our seqno tracking.
Anecdotally, I observed lost breadcrumbs writes into the HWS on i965gm,
which so far have not reoccurred with this patch. How reliable that
evidence is remains to be seen.
v2: Explicitly pass the expected physical address to the hw
v3: Also remember the wild writes we once had for HWS above 4G.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180903152304.31589-2-chris@chris-wilson.co.uk
We need to clear the register in order to get correct value after the
next potential hang.
v2: Centralize error register clearing in i915_irq.c (Chris)
v3: Don't read gen8 register on < gen6 (Chris)
v4: Don't swap gen8+ & gen6+ code... (Chris)
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180830132424.21940-1-lionel.g.landwerlin@intel.com
Ville Syrjälä