Currently, an empty disk->events field tells the block layer not to
forward media change events to user space. This was done in commit
7c88a168da ("block: don't propagate unlisted DISK_EVENTs to userland")
in order to avoid events from "fringe" drivers to be forwarded to user
space. By doing so, the block layer lost the information which events
were supported by a particular block device, and most importantly,
whether or not a given device supports media change events at all.
Prepare for not interpreting the "events" field this way in the future
any more. This is done by adding an additional field "event_flags" to
struct gendisk, and two flag bits that can be set to have the device
treated like one that had the "events" field set to a non-zero value
before. This applies only to the sd and sr drivers, which are changed to
set the new flags.
The new flags are DISK_EVENT_FLAG_POLL to enforce polling of the device
for synchronous events, and DISK_EVENT_FLAG_UEVENT to tell the
blocklayer to generate udev events from kernel events.
In order to add the event_flags field to struct gendisk, the events
field is converted to an "unsigned short"; it doesn't need to hold
values bigger than 2 anyway.
This patch doesn't change behavior.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
No more need in a blk-mq world where the scsi command and request are
allocated together.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Replace the old BLKPREP_* values with the BLK_STS_ ones that they are
converted to later anyway.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Update device_add_disk() to take an 'groups' argument so that
individual drivers can register a device with additional sysfs
attributes.
This avoids race condition the driver would otherwise have if these
groups were to be created with sysfs_add_groups().
Signed-off-by: Martin Wilck <martin.wilck@suse.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move the code for runtime power management from blk-core.c into the
new source file blk-pm.c. Move the corresponding declarations from
<linux/blkdev.h> into <linux/blk-pm.h>. For CONFIG_PM=n, leave out
the declarations of the functions that are not used in that mode.
This patch not only reduces the number of #ifdefs in the block layer
core code but also reduces the size of header file <linux/blkdev.h>
and hence should help to reduce the build time of the Linux kernel
if CONFIG_PM is not defined.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Jianchao Wang <jianchao.w.wang@oracle.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Surround scsi_execute() calls with scsi_autopm_get_device() and
scsi_autopm_put_device(). Note: removing sr_mutex protection from the
scsi_cd_get() and scsi_cd_put() calls is safe because the purpose of
sr_mutex is to serialize cdrom_*() calls.
This patch avoids that complaints similar to the following appear in the
kernel log if runtime power management is enabled:
INFO: task systemd-udevd:650 blocked for more than 120 seconds.
Not tainted 4.18.0-rc7-dbg+ #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
systemd-udevd D28176 650 513 0x00000104
Call Trace:
__schedule+0x444/0xfe0
schedule+0x4e/0xe0
schedule_preempt_disabled+0x18/0x30
__mutex_lock+0x41c/0xc70
mutex_lock_nested+0x1b/0x20
__blkdev_get+0x106/0x970
blkdev_get+0x22c/0x5a0
blkdev_open+0xe9/0x100
do_dentry_open.isra.19+0x33e/0x570
vfs_open+0x7c/0xd0
path_openat+0x6e3/0x1120
do_filp_open+0x11c/0x1c0
do_sys_open+0x208/0x2d0
__x64_sys_openat+0x59/0x70
do_syscall_64+0x77/0x230
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Maurizio Lombardi <mlombard@redhat.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: <stable@vger.kernel.org>
Tested-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
when mounting an ISO filesystem sometimes (very rarely)
the system hangs because of a race condition between two tasks.
PID: 6766 TASK: ffff88007b2a6dd0 CPU: 0 COMMAND: "mount"
#0 [ffff880078447ae0] __schedule at ffffffff8168d605
#1 [ffff880078447b48] schedule_preempt_disabled at ffffffff8168ed49
#2 [ffff880078447b58] __mutex_lock_slowpath at ffffffff8168c995
#3 [ffff880078447bb8] mutex_lock at ffffffff8168bdef
#4 [ffff880078447bd0] sr_block_ioctl at ffffffffa00b6818 [sr_mod]
#5 [ffff880078447c10] blkdev_ioctl at ffffffff812fea50
#6 [ffff880078447c70] ioctl_by_bdev at ffffffff8123a8b3
#7 [ffff880078447c90] isofs_fill_super at ffffffffa04fb1e1 [isofs]
#8 [ffff880078447da8] mount_bdev at ffffffff81202570
#9 [ffff880078447e18] isofs_mount at ffffffffa04f9828 [isofs]
#10 [ffff880078447e28] mount_fs at ffffffff81202d09
#11 [ffff880078447e70] vfs_kern_mount at ffffffff8121ea8f
#12 [ffff880078447ea8] do_mount at ffffffff81220fee
#13 [ffff880078447f28] sys_mount at ffffffff812218d6
#14 [ffff880078447f80] system_call_fastpath at ffffffff81698c49
RIP: 00007fd9ea914e9a RSP: 00007ffd5d9bf648 RFLAGS: 00010246
RAX: 00000000000000a5 RBX: ffffffff81698c49 RCX: 0000000000000010
RDX: 00007fd9ec2bc210 RSI: 00007fd9ec2bc290 RDI: 00007fd9ec2bcf30
RBP: 0000000000000000 R8: 0000000000000000 R9: 0000000000000010
R10: 00000000c0ed0001 R11: 0000000000000206 R12: 00007fd9ec2bc040
R13: 00007fd9eb6b2380 R14: 00007fd9ec2bc210 R15: 00007fd9ec2bcf30
ORIG_RAX: 00000000000000a5 CS: 0033 SS: 002b
This task was trying to mount the cdrom. It allocated and configured a
super_block struct and owned the write-lock for the super_block->s_umount
rwsem. While exclusively owning the s_umount lock, it called
sr_block_ioctl and waited to acquire the global sr_mutex lock.
PID: 6785 TASK: ffff880078720fb0 CPU: 0 COMMAND: "systemd-udevd"
#0 [ffff880078417898] __schedule at ffffffff8168d605
#1 [ffff880078417900] schedule at ffffffff8168dc59
#2 [ffff880078417910] rwsem_down_read_failed at ffffffff8168f605
#3 [ffff880078417980] call_rwsem_down_read_failed at ffffffff81328838
#4 [ffff8800784179d0] down_read at ffffffff8168cde0
#5 [ffff8800784179e8] get_super at ffffffff81201cc7
#6 [ffff880078417a10] __invalidate_device at ffffffff8123a8de
#7 [ffff880078417a40] flush_disk at ffffffff8123a94b
#8 [ffff880078417a88] check_disk_change at ffffffff8123ab50
#9 [ffff880078417ab0] cdrom_open at ffffffffa00a29e1 [cdrom]
#10 [ffff880078417b68] sr_block_open at ffffffffa00b6f9b [sr_mod]
#11 [ffff880078417b98] __blkdev_get at ffffffff8123ba86
#12 [ffff880078417bf0] blkdev_get at ffffffff8123bd65
#13 [ffff880078417c78] blkdev_open at ffffffff8123bf9b
#14 [ffff880078417c90] do_dentry_open at ffffffff811fc7f7
#15 [ffff880078417cd8] vfs_open at ffffffff811fc9cf
#16 [ffff880078417d00] do_last at ffffffff8120d53d
#17 [ffff880078417db0] path_openat at ffffffff8120e6b2
#18 [ffff880078417e48] do_filp_open at ffffffff8121082b
#19 [ffff880078417f18] do_sys_open at ffffffff811fdd33
#20 [ffff880078417f70] sys_open at ffffffff811fde4e
#21 [ffff880078417f80] system_call_fastpath at ffffffff81698c49
RIP: 00007f29438b0c20 RSP: 00007ffc76624b78 RFLAGS: 00010246
RAX: 0000000000000002 RBX: ffffffff81698c49 RCX: 0000000000000000
RDX: 00007f2944a5fa70 RSI: 00000000000a0800 RDI: 00007f2944a5fa70
RBP: 00007f2944a5f540 R8: 0000000000000000 R9: 0000000000000020
R10: 00007f2943614c40 R11: 0000000000000246 R12: ffffffff811fde4e
R13: ffff880078417f78 R14: 000000000000000c R15: 00007f2944a4b010
ORIG_RAX: 0000000000000002 CS: 0033 SS: 002b
This task tried to open the cdrom device, the sr_block_open function
acquired the global sr_mutex lock. The call to check_disk_change()
then saw an event flag indicating a possible media change and tried
to flush any cached data for the device.
As part of the flush, it tried to acquire the super_block->s_umount
lock associated with the cdrom device.
This was the same super_block as created and locked by the previous task.
The first task acquires the s_umount lock and then the sr_mutex_lock;
the second task acquires the sr_mutex_lock and then the s_umount lock.
This patch fixes the issue by moving check_disk_change() out of
cdrom_open() and let the caller take care of it.
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Before scsi_prep_fn() calls the ULP .init_command() callback
function it stores the SCSI command pointer in request.special.
This means that the SCpnt = rq->special assignments in the sd
and sr drivers assign a pointer to itself. Hence convert these
two assignment statements into warning statements.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kefeng Wang discovered that old versions of the QEMU CD driver would
return mangled mode data causing us to walk off the end of the buffer in
an attempt to parse it. Sanity check the returned mode sense data.
Cc: <stable@vger.kernel.org>
Reported-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Tested-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since function tables are a common target for attackers, it's best to keep
them in read-only memory. As such, this makes the CDROM device ops tables
const. This drops additionally n_minors, since it isn't used meaningfully,
and sets the only user of cdrom_dummy_generic_packet explicitly so the
variables can all be const.
Inspired by similar changes in grsecurity/PaX.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jens Axboe <axboe@fb.com>
Instead of keeping two levels of indirection for requests types, fold it
all into the operations. The little caveat here is that previously
cmd_type only applied to struct request, while the request and bio op
fields were set to plain REQ_OP_READ/WRITE even for passthrough
operations.
Instead this patch adds new REQ_OP_* for SCSI passthrough and driver
private requests, althought it has to add two for each so that we
can communicate the data in/out nature of the request.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sr_pm_ops, of type struct dev_pm_ops, is never modified, so declare it
as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For block drivers that specify a parent device, convert them to use
device_add_disk().
This conversion was done with the following semantic patch:
@@
struct gendisk *disk;
expression E;
@@
- disk->driverfs_dev = E;
...
- add_disk(disk);
+ device_add_disk(E, disk);
@@
struct gendisk *disk;
expression E1, E2;
@@
- disk->driverfs_dev = E1;
...
E2 = disk;
...
- add_disk(E2);
+ device_add_disk(E1, E2);
...plus some manual fixups for a few missed conversions.
Cc: Jens Axboe <axboe@fb.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: James Bottomley <James.Bottomley@hansenpartnership.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Runtime suspend during driver probe and removal can cause problems.
The driver's runtime_suspend or runtime_resume callbacks may invoked
before the driver has finished binding to the device or after the
driver has unbound from the device.
This problem shows up with the sd and sr drivers, and can cause disk
or CD/DVD drives to become unusable as a result. The fix is simple.
The drivers store a pointer to the scsi_disk or scsi_cd structure as
their private device data when probing is finished, so we simply have
to be sure to clear the private data during removal and test it during
runtime suspend/resume.
This fixes <https://bugs.debian.org/801925>.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Paul Menzel <paul.menzel@giantmonkey.de>
Reported-by: Erich Schubert <erich@debian.org>
Reported-by: Alexandre Rossi <alexandre.rossi@gmail.com>
Tested-by: Paul Menzel <paul.menzel@giantmonkey.de>
Tested-by: Erich Schubert <erich@debian.org>
CC: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The driver core driver structure has grown an owner field and now
requires it to be set for all modular drivers. Set it up for
all scsi_driver instances and get rid of the now superflous
scsi_driver owner field.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Shane M Seymour <shane.seymour@hp.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
There is no reason for ULDs to pass in a flag on how to allocate the S/G
lists. While we don't need GFP_ATOMIC for the blk-mq case because we
don't hold locks, that decision can be made way down the chain without
having to pass a pointless gfp_mask argument.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
The calling conventions for this function are bad as it could return
-ENODEV both for a device not currently online and a not recognized ioctl.
Add a new scsi_ioctl_block_when_processing_errors function that wraps
scsi_block_when_processing_errors with the a special case for the
SG_SCSI_RESET ioctl command, and handle the SG_SCSI_RESET case itself
in scsi_ioctl. All callers of scsi_ioctl now must call the above helper
to check for the EH state, so that the ioctl handler itself doesn't
have to.
Reported-by: Robert Elliott <Elliott@hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
SCSI Well-known logical units generally don't have any scsi driver
associated with it which means no one will call scsi_autopm_put_device()
on these wlun scsi devices and this would result in keeping the
corresponding scsi device always active (hence LLD can't be suspended as
well). Same exact problem can be seen for other scsi device representing
normal logical unit whose driver is yet to be loaded. This patch fixes
the above problem with this approach:
- make the scsi_autopm_put_device call at the end of scsi_sysfs_add_sdev
to make it balance out the get earlier in the function.
- let drivers do paired get/put calls in their probe methods.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
We currently set the field in common code based on the device type,
but then only use it in the cdrom driver which also overrides the
value previously set in the generic code.
Just leave this entirely to the CDROM driver to make everyones life
simpler.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
The data direction fiel in the SCSI command is derived only from the block
request structure. Move setting it up into common code instead of
duplicating it in the ULDs.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
We should call the device handler prep_fn for all TYPE_FS requests,
not just simple read/write calls that are handled by the disk driver.
Restructure the common I/O code to call the prep_fn handler and zero
out the CDB, and just leave the call to scsi_init_io to the ULDs.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Update the sr driver to use dev_printk() variants instead of
plain printk(); this will prefix logging messages with the
appropriate device.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Instead of letting the ULD play games with the prep_fn move back to
the model of a central prep_fn with a callback to the ULD. This
already cleans up and shortens the code by itself, and will be required
to properly support blk-mq in the SCSI midlayer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Nicholas Bellinger <nab@linux-iscsi.org>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Migrate sr to make use of block layer runtime PM. Accordingly, the
SCSI bus layer runtime PM callback is simplified as all SCSI drivers
implementing runtime PM now use the block layer's request-based
mechanism.
Note that due to the device will be polled by kernel at a constant
interval, if the autosuspend delay is set longer than the polling
interval then the device will never suspend.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The value passed is 0 in all but "it can never happen" cases (and those
only in a couple of drivers) *and* it would've been lost on the way
out anyway, even if something tried to pass something meaningful.
Just don't bother.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
When the ODD is powered off, any action the user did to the ODD that
would generate a media event will trigger an ACPI interrupt, so the
poll for media event is no longer necessary. And the poll will also
cause a runtime status change, which will stop the ODD from staying in
powered off state, so the poll should better be stopped.
But since we don't have access to the gendisk structure in LLDs, here
comes the disk_events_disable_depth for scsi device. This field is a
hint set by LLDs to convey information to upper layer drivers. A value
of 0 means media poll is necessary for the device, while values above 0
means media poll is not needed and should better be skipped. So we can
increase its value when we are to power off the ODD in ATA layer and
decrease its value when the ODD is powered on, effectively silence the
media events poll.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds runtime pm support for sr.
It did this by increasing the runtime usage_count of the device when
its block device is accessed. And decreasing the runtime usage_count
of the device when the access is done.
If there is media inside, runtime suspend is not allowed as we don't
always know if the ODD is being used or not.
The idea is discussed here:
http://thread.gmane.org/gmane.linux.acpi.devel/55243/focus=52703
and the restriction to check media inside is discussed here:
http://thread.gmane.org/gmane.linux.ide/53665/focus=58836
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some broken devices indicates that media has changed on every
GET_EVENT_STATUS_NOTIFICATION. This translates into MEDIA_CHANGE
uevent on every open() which lets udev run into a loop.
Verify GET_EVENT result against TUR and if it generates spurious
events for several times in a row, ignore the GET_EVENT events, and
trust only the TUR status.
This is the log of a USB stick with a (broken) fake CDROM drive:
scsi 5:0:0:0: Direct-Access SanDisk U3 Cruzer Micro 8.02 PQ: 0 ANSI: 0 CCS
sd 5:0:0:0: Attached scsi generic sg3 type 0
scsi 5:0:0:1: CD-ROM SanDisk U3 Cruzer Micro 8.02 PQ: 0 ANSI: 0
sd 5:0:0:0: [sdb] Attached SCSI removable disk
sr2: scsi3-mmc drive: 48x/48x tray
sr 5:0:0:1: Attached scsi CD-ROM sr2
sr 5:0:0:1: Attached scsi generic sg4 type 5
sr2: GET_EVENT and TUR disagree continuously, suppress GET_EVENT events
sd 5:0:0:0: [sdb] 31777279 512-byte logical blocks: (16.2 GB/15.1 GiB)
sd 5:0:0:0: [sdb] No Caching mode page present
sd 5:0:0:0: [sdb] Assuming drive cache: write through
sd 5:0:0:0: [sdb] No Caching mode page present
sd 5:0:0:0: [sdb] Assuming drive cache: write through
sdb: sdb1
-tj: Updated to consider only spurious GET_EVENT events among
different types of disagreement and allow using TUR for kernel
event polling after GET_EVENT is ignored.
Reported-By: Markus Rathgeb maggu2810@googlemail.com
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@kernel.org # >= v2.6.38, fixes udev busy looping w/ certain devices
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Disk event code automatically blocks events on excl write. This is
primarily to avoid issuing polling commands while burning is in
progress. This behavior doesn't fit other types of devices with
removeable media where polling commands don't have adverse side
effects and door locking usually doesn't exist.
This patch introduces new genhd flag which controls the auto-blocking
behavior and uses it to enable auto-blocking only on optical devices.
Note for stable: 2.6.38 and later only
Cc: stable@kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
SDEV_MEDIA_CHANGE event was first added by commit a341cd0f (SCSI: add
asynchronous event notification API) for SATA AN support and then
extended to cover generic media change events by commit 285e9670
([SCSI] sr,sd: send media state change modification events).
This event was mapped to block device in userland with all properties
stripped to simulate CHANGE event on the block device, which, in turn,
was used to trigger further userspace action on media change.
The recent addition of disk event framework kept this event for
backward compatibility but it turns out to be unnecessary and causes
erratic and inefficient behavior. The new disk event generates proper
events on the block devices and the compat events are mapped to block
device with all properties stripped, so the block device ends up
generating multiple duplicate events for single actual event.
This patch removes the compat event generation from both sr and sd as
suggested by Kay Sievers. Both existing and newer versions of udev
and the associated tools will behave better with the removal of these
events as they from the beginning were expecting events on the block
devices.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Replace sr_media_change() with sr_check_events(). It normally only
uses GET_EVENT_STATUS_NOTIFICATION to check both media change and
eject request. If @clearing includes DISK_EVENT_MEDIA_CHANGE, it
issues TUR and compares whether media presence has changed. The SCSI
specific media change uevent is kept for compatibility.
sr_media_change() was doing both media change check and revalidation.
The revalidation part is split into sr_block_revalidate_disk().
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The usage of TUR has been confusing involving several different
commits updating different parts over time. Currently, the only
differences between scsi_test_unit_ready() and sr_test_unit_ready()
are,
* scsi_test_unit_ready() also sets sdev->changed on NOT_READY.
* scsi_test_unit_ready() returns 0 if TUR ended with UNIT_ATTENTION or
NOT_READY.
Due to the above two differences, sr is using its own
sr_test_unit_ready(), but sd - the sole user of the above extra
handling - doesn't even need them.
Where scsi_test_unit_ready() is used in sd_media_changed(), the code
is looking for device ready w/ media present state which is true iff
TUR succeeds w/o sense data or UA, and when the device is not ready
for whatever reason sd_media_changed() explicitly marks media as
missing so there's no reason to set sdev->changed automatically from
scsi_test_unit_ready() on NOT_READY.
Drop both special handlings from scsi_test_unit_ready(), which makes
it equivalant to sr_test_unit_ready(), and replace
sr_test_unit_ready() with scsi_test_unit_ready(). Also, drop the
unnecessary explicit NOT_READY check from sd_media_changed().
Checking return value is enough for testing device readiness.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
sr_test_unit_ready() returns 0 iff TUR succeeded - IOW, when media is
present and the device is actually ready, so the return value wouldn't
be zero when TUR ends with sense data. sr_media_change() incorrectly
tests (retval || (scsi_sense_valid(sshdr)...)) when it tries to test
whether TUR failed without sense data or with sense data indicating
media-not-present.
Fix the test using scsi_status_is_good() and update comments.
- Fixed a comment typo spotted by Eike.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Rolf Eike Beer <eike-kernel@sf-tec.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (141 commits)
USB: mct_u232: fix broken close
USB: gadget: amd5536udc.c: fix error path
USB: imx21-hcd - fix off by one resource size calculation
usb: gadget: fix Kconfig warning
usb: r8a66597-udc: Add processing when USB was removed.
mxc_udc: add workaround for ENGcm09152 for i.MX35
USB: ftdi_sio: add device ids for ScienceScope
USB: musb: AM35x: Workaround for fifo read issue
USB: musb: add musb support for AM35x
USB: AM35x: Add musb support
usb: Fix linker errors with CONFIG_PM=n
USB: ohci-sh - use resource_size instead of defining its own resource_len macro
USB: isp1362-hcd - use resource_size instead of defining its own resource_len macro
USB: isp116x-hcd - use resource_size instead of defining its own resource_len macro
USB: xhci: Fix compile error when CONFIG_PM=n
USB: accept some invalid ep0-maxpacket values
USB: xHCI: PCI power management implementation
USB: xHCI: bus power management implementation
USB: xHCI: port remote wakeup implementation
USB: xHCI: port power management implementation
...
Manually fix up (non-data) conflict: the SCSI merge gad renamed the
'hw_sector_size' member to 'physical_block_size', and the USB tree
brought a new use of it.
Some USB devices emulate a usb-mass-storage attached (scsi) cdrom device,
usually this fake cdrom contains the windows software for the device.
While working on supporting Appotech ax3003 based photoframes, which do
this I discovered that they will go of into lala land when ever they see a
READ_DISC_INFO scsi command.
Thus this patch adds a scsi_device flag (which can then be set by the
usb-storage driver through an unsual-devs entry), to indicate this, and
makes the sr driver honor this flag.
I know this sucks, but as discussed on linux-scsi list there is no other
way to make this device work properly.
Looking at usb traces made under windows, windows never sends a
READ_DISC_INFO during normal interactions with a usb cdrom device. So as
this cdrom emulation thingie becomes more common we might see more of this
problem.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The block device drivers have all gained new lock_kernel
calls from a recent pushdown, and some of the drivers
were already using the BKL before.
This turns the BKL into a set of per-driver mutexes.
Still need to check whether this is safe to do.
file=$1
name=$2
if grep -q lock_kernel ${file} ; then
if grep -q 'include.*linux.mutex.h' ${file} ; then
sed -i '/include.*<linux\/smp_lock.h>/d' ${file}
else
sed -i 's/include.*<linux\/smp_lock.h>.*$/include <linux\/mutex.h>/g' ${file}
fi
sed -i ${file} \
-e "/^#include.*linux.mutex.h/,$ {
1,/^\(static\|int\|long\)/ {
/^\(static\|int\|long\)/istatic DEFINE_MUTEX(${name}_mutex);
} }" \
-e "s/\(un\)*lock_kernel\>[ ]*()/mutex_\1lock(\&${name}_mutex)/g" \
-e '/[ ]*cycle_kernel_lock();/d'
else
sed -i -e '/include.*\<smp_lock.h\>/d' ${file} \
-e '/cycle_kernel_lock()/d'
fi
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The open and release block_device_operations are currently
called with the BKL held. In order to change that, we must
first make sure that all drivers that currently rely
on this have no regressions.
This blindly pushes the BKL into all .open and .release
operations for all block drivers to prepare for the
next step. The drivers can subsequently replace the BKL
with their own locks or remove it completely when it can
be shown that it is not needed.
The functions blkdev_get and blkdev_put are the only
remaining users of the big kernel lock in the block
layer, besides a few uses in the ioctl code, none
of which need to serialize with blkdev_{get,put}.
Most of these two functions is also under the protection
of bdev->bd_mutex, including the actual calls to
->open and ->release, and the common code does not
access any global data structures that need the BKL.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
As a preparation for the removal of the big kernel
lock in the block layer, this removes the BKL
from the common ioctl handling code, moving it
into every single driver still using it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
On certain cases, UDF disc doesn't report capacity correctly via
READ_CAPACITY but TOC or trackinfo contains valid information which
can be obtained using cdrom_get_last_written(). ide-cd considers both
values and uses the larger one. Do the same in sr. This fixes
bko#9668.
http://bugzilla.kernel.org/show_bug.cgi?id=9668
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Milan Kocian <milan.kocian@wq.cz>
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
If a SCSI ULD driver sets blk_queue_prep_rq(), it should clean it
up itself on remove(), and not from the bus callbacks. This
removes the need to hook into bus->remove(), which should not
be used at the same time as driver->remove().
[jejb: fix sdkp initialisation problem due to mismerge]
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Until now we have had a 1:1 mapping between storage device physical
block size and the logical block sized used when addressing the device.
With SATA 4KB drives coming out that will no longer be the case. The
sector size will be 4KB but the logical block size will remain
512-bytes. Hence we need to distinguish between the physical block size
and the logical ditto.
This patch renames hardsect_size to logical_block_size.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
With recent cleanups, there is no place where low level driver
directly manipulates request fields. This means that the 'hard'
request fields always equal the !hard fields. Convert all
rq->sectors, nr_sectors and current_nr_sectors references to
accessors.
While at it, drop superflous blk_rq_pos() < 0 test in swim.c.
[ Impact: use pos and nr_sectors accessors ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Tested-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Acked-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Acked-by: Mike Miller <mike.miller@hp.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Tim Waugh <tim@cyberelk.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Dario Ballabio <ballabio_dario@emc.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: unsik Kim <donari75@gmail.com>
Cc: Laurent Vivier <Laurent@lvivier.info>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
We have a problem with recovered error handling in that any command
which goes down as BLOCK_PC but which returns a sense code of RECOVERED
ERROR gets completed with -EIO. For actual SG_IO commands, this doesn't
matter at all, since the error return code gets dropped in favour of
req->errors which contain the SCSI completion code.
However, if this command is part of the block system, then it will pay
attention to the returned error code. In particularly if a SYNCHRONIZE
CACHE from a barrier command completes with RECOVERED ERROR, the
resulting -EIO on the barrier causes block to error the request and
return it to the filesystem. Fix this by converting the -EIO for
recovered error to zero, plus remove the printing of this from sd and sr
so the message isn't double printed.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
scsi_execute() and scsi_execute_req() discard the residual length
information. Some callers need it. This adds residual argument
(optional) to scsi_execute and scsi_execute_req.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Martin Wilck