Building target_core_alua.o triggers a GCC warning:
drivers/target/target_core_alua.c: In function ‘target_alua_state_check’:
drivers/target/target_core_alua.c:773:18: warning: ‘alua_ascq’ may be used uninitialized in this function [-Wmaybe-uninitialized]
cmd->scsi_ascq = alua_ascq;
^
This is a false positive. A little trial and error shows it is
apparently caused by core_alua_state_lba_dependent(). It must be hard
for GCC to track the branches of a switch statement, inside a
list_for_each_entry loop, inside a while loop.
But if we add a small (inline) helper function we can reorganize the
code a bit. That also allows to drop alua_ascq which, obviously, gets
rid of this warning.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
When copying between device and command protection scatters
we must take into account that device scatters might be offset
and we might copy outside scatter range. Thus for each cmd prot
scatter we must take the min between cmd prot scatter, dev prot
scatter, and whats left (and loop in case we havn't copied enough
from/to cmd prot scatter).
Example (single t_prot_sg of len 2048):
kernel: sbc_dif_copy_prot: se_cmd=ffff880380aaf970, left=2048, len=2048, dev_prot_sg_offset=3072, dev_prot_sg_len=4096
kernel: isert: se_cmd=ffff880380aaf970 PI error found type 0 at sector 0x2600 expected 0x0 vs actual 0x725f, lba=2580
Instead of copying 2048 from offset 3072 (copying junk outside sg
limit 4096), we must to copy 1024 and continue to next sg until
we complete cmd prot scatter.
This issue was found using iSER T10-PI offload over rd_mcp (wasn't
discovered with fileio since file_dev prot sglists are never offset).
Changes from v1:
- Fix sbc_copy_prot copy length miss-calculation
Changes from v0:
- Removed psg->offset consideration for psg_len computation
- Removed sg->offset consideration for offset condition
- Added copied consideraiton for len computation
- Added copied offset to paddr when doing memcpy
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses a couple of different hug shutdown issues
related to wait_event() + isert_conn->state. First, it changes
isert_conn->conn_wait + isert_conn->conn_wait_comp_err from
waitqueues to completions, and sets ISER_CONN_TERMINATING from
within isert_disconnect_work().
Second, it splits isert_free_conn() into isert_wait_conn() that
is called earlier in iscsit_close_connection() to ensure that
all outstanding commands have completed before continuing.
Finally, it breaks isert_cq_comp_err() into seperate TX / RX
related code, and adds logic in isert_cq_rx_comp_err() to wait
for outstanding commands to complete before setting ISER_CONN_DOWN
and calling complete(&isert_conn->conn_wait_comp_err).
Acked-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: <stable@vger.kernel.org> #3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
There are a handful of uses of list_empty() for cmd->i_conn_node
within iser-target code that expect to return false once a cmd
has been removed from the per connect list.
This patch changes all uses of list_del -> list_del_init in order
to ensure that list_empty() returns false as expected.
Acked-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: <stable@vger.kernel.org> #3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a bug in iscsit_get_tpg_from_np() where the
tpg->tpg_state sanity check was looking for TPG_STATE_FREE,
instead of != TPG_STATE_ACTIVE.
The latter is expected during a normal TPG shutdown once the
tpg_state goes into TPG_STATE_INACTIVE in order to reject any
new incoming login attempts.
Cc: <stable@vger.kernel.org> #3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Because then this sg is passed to sbc_copy_prot which will
hit a protection fault in cases we have more than a single sg.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds the three missing DIF related sense codes within
transport_generic_request_failure(), which are required to ensure
that the correct ASC/ASQC is generated by the subsequent call to
transport_send_check_condition_and_sense().
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a bug in sbc_dif_copy_prot() where the updated addr
offset did not take into account the case where the associated
scatterlist had not been incremented.
This addresses the case where incoming protection scatterlists may
contain a length smaller than PAGE_SIZE across multiple entires,
when the target protection scatterlists are always being explicitly
filled up to PAGE_SIZE before adding another entry.
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Need to take into account that protection sg_list
(copy-buffer) may consist of multiple entries.
Changes from v0:
- Changed commit description
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The CMD_T_FAILED flag is set used in one place to record the result of a
trivial test, and it is only tested once, few lines later. We might as
well make the code simpler and easier to read by directly doing the test
of "success" where we want to use it.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes Status SNACK handling of BegRun=0 to allow
for all unacknowledged respones to be resent, instead of
always assuming that BegRun would be an explicit value less
than the current ExpStatSN.
Reported-by: santosh kulkarni <santosh.kulkarni@calsoftinc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Commit fbfe858fea ("target_core_spc: Include target device
descriptor in VPD page 83") added a new length variable, but (due to a
cut and paste mistake?) just checks scsi_name_len against 256 twice.
Fix this to check scsi_target_len for overflow too.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes core_alua_state_lba_dependent() to use do_div()
instead sector_div() to avoid the following link error on 32-bit
with CONFIG_LBDAF=n as reported by Jim:
buildlog-1391099072.txt-drivers/built-in.o: In function `target_alua_state_check':
buildlog-1391099072.txt-(.text+0x928d93): undefined reference to `__umoddi3'
buildlog-1391099072.txt:make: *** [vmlinux] Error 1 --
buildlog-1391101753.txt- CC init/version.o
buildlog-1391101753.txt- LD init/built-in.o
buildlog-1391101753.txt-drivers/built-in.o: In function `core_alua_state_lba_dependent':
buildlog-1391101753.txt-/home/jim/linux/drivers/target/target_core_alua.c:503: undefined reference to `__umoddi3'
buildlog-1391101753.txt:make: *** [vmlinux] Error 1
Reported-by: Jim Davis <jim.epost@gmail.com>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses a >= v3.11 free-after-use regression
in core_scsi3_emulate_pro_register() that was introduced
in the following commit:
commit bc118fe4c4
Author: Andy Grover <agrover@redhat.com>
Date: Thu May 16 10:41:04 2013 -0700
target: Further refactoring of core_scsi3_emulate_pro_register()
To avoid the free-after-use, save an type value before hand, and
only call core_scsi3_put_pr_reg() with a valid *pr_reg.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Andy Grover <agrover@redhat.com>
Cc: <stable@vger.kernel.org> #3.11+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull SCSI target updates from Nicholas Bellinger:
"The highlights this round include:
- add support for SCSI Referrals (Hannes)
- add support for T10 DIF into target core (nab + mkp)
- add support for T10 DIF emulation in FILEIO + RAMDISK backends (Sagi + nab)
- add support for T10 DIF -> bio_integrity passthrough in IBLOCK backend (nab)
- prep changes to iser-target for >= v3.15 T10 DIF support (Sagi)
- add support for qla2xxx N_Port ID Virtualization - NPIV (Saurav + Quinn)
- allow percpu_ida_alloc() to receive task state bitmask (Kent)
- fix >= v3.12 iscsi-target session reset hung task regression (nab)
- fix >= v3.13 percpu_ref se_lun->lun_ref_active race (nab)
- fix a long-standing network portal creation race (Andy)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (51 commits)
target: Fix percpu_ref_put race in transport_lun_remove_cmd
target/iscsi: Fix network portal creation race
target: Report bad sector in sense data for DIF errors
iscsi-target: Convert gfp_t parameter to task state bitmask
iscsi-target: Fix connection reset hang with percpu_ida_alloc
percpu_ida: Make percpu_ida_alloc + callers accept task state bitmask
iscsi-target: Pre-allocate more tags to avoid ack starvation
qla2xxx: Configure NPIV fc_vport via tcm_qla2xxx_npiv_make_lport
qla2xxx: Enhancements to enable NPIV support for QLOGIC ISPs with TCM/LIO.
qla2xxx: Fix scsi_host leak on qlt_lport_register callback failure
IB/isert: pass scatterlist instead of cmd to fast_reg_mr routine
IB/isert: Move fastreg descriptor creation to a function
IB/isert: Avoid frwr notation, user fastreg
IB/isert: seperate connection protection domains and dma MRs
tcm_loop: Enable DIF/DIX modes in SCSI host LLD
target/rd: Add DIF protection into rd_execute_rw
target/rd: Add support for protection SGL setup + release
target/rd: Refactor rd_build_device_space + rd_release_device_space
target/file: Add DIF protection support to fd_execute_rw
target/file: Add DIF protection init/format support
...
This patch fixes a percpu_ref_put race for se_lun->lun_ref in
transport_lun_remove_cmd() where ->lun_ref could end up being
put more than once per command via different target completion
and fabric release contexts.
It adds a cmpxchg() for se_cmd->lun_ref_active to ensure that
percpu_ref_put() is only ever called once per se_cmd.
This bug was manifesting itself as a LUN shutdown regression
bug in >= v3.13 code, where percpu_ref_kill() would end up
hanging indefinately due to the incorrect percpu_ref count.
(Change se_cmd->lun_ref_active from bool -> int to force at
least a 4-byte cmpxchg with MIPS ll/sc ins. - Fengguang)
Reported-by: Tommy Apel <tommyapeldk@gmail.com>
Cc: Tommy Apel <tommyapeldk@gmail.com>
Cc: <stable@vger.kernel.org> #3.13+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
When creating network portals rapidly, such as when restoring a
configuration, LIO's code to reuse existing portals can return a false
negative if the thread hasn't run yet and set np_thread_state to
ISCSI_NP_THREAD_ACTIVE. This causes an error in the network stack
when attempting to bind to the same address/port.
This patch sets NP_THREAD_ACTIVE before the np is placed on g_np_list,
so even if the thread hasn't run yet, iscsit_get_np will return the
existing np.
Also, convert np_lock -> np_mutex + hold across adding new net portal
to g_np_list to prevent a race where two threads may attempt to create
the same network portal, resulting in one of them failing.
(nab: Add missing mutex_unlocks in iscsit_add_np failure paths)
(DanC: Fix incorrect spin_unlock -> spin_unlock_bh)
Signed-off-by: Andy Grover <agrover@redhat.com>
Cc: <stable@vger.kernel.org> #3.1+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
SPC-4 states that data-integrity errors shall also report
the failed sector in CHECK_CONDITION response sense data
information field.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch propigates the use of task state bitmask now used by
percpu_ida_alloc() up the iscsi-target callchain, replacing the
use of GFP_ATOMIC for TASK_RUNNING, and GFP_KERNEL for
TASK_INTERRUPTIBLE.
Also, drop the unnecessary gfp_t parameter to isert_allocate_cmd(),
and just pass TASK_INTERRUPTIBLE into iscsit_allocate_cmd().
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses a bug where connection reset would hang
indefinately once percpu_ida_alloc() was starved for tags, due
to the fact that it always assumed uninterruptible sleep mode.
So now make percpu_ida_alloc() check for signal_pending_state() for
making interruptible sleep optional, and convert iscsit_allocate_cmd()
to set TASK_INTERRUPTIBLE for GFP_KERNEL, or TASK_RUNNING for
GFP_ATOMIC.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Kent Overstreet <kmo@daterainc.com>
Cc: <stable@vger.kernel.org> #3.12+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes percpu_ida_alloc() + callers to accept task state
bitmask for prepare_to_wait() for code like target/iscsi that needs
it for interruptible sleep, that is provided in a subsequent patch.
It now expects TASK_UNINTERRUPTIBLE when the caller is able to sleep
waiting for a new tag, or TASK_RUNNING when the caller cannot sleep,
and is forced to return a negative value when no tags are available.
v2 changes:
- Include blk-mq + tcm_fc + vhost/scsi + target/iscsi changes
- Drop signal_pending_state() call
v3 changes:
- Only call prepare_to_wait() + finish_wait() when != TASK_RUNNING
(PeterZ)
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: <stable@vger.kernel.org> #3.12+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses an traditional iscsi-target fabric ack starvation
issue where iscsit_allocate_cmd() -> percpu_ida_alloc_state() ends up
hitting slow path percpu-ida code, because iscsit_ack_from_expstatsn()
is expected to free ack'ed tags after tag allocation.
This is done to take into account the tags waiting to be acknowledged
and released in iscsit_ack_from_expstatsn(), but who's number are not
directly limited by the CmdSN Window queue_depth being enforced by
the target.
So that said, this patch bumps up the pre-allocated number of
per session tags to:
(max(queue_depth, ISCSIT_MIN_TAGS) * 2) + ISCSIT_EXTRA_TAGS
for good measure to avoid the percpu_ida_alloc_state() slow path.
Cc: <stable@vger.kernel.org> #3.12+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch updates tcm_loop_driver_probe() to set protection
information using scsi_host_set_prot() and scsi_host_set_guard(),
which currently enabled all modes of DIF/DIX protection, minus
DIX TYPE0.
Also, update tcm_loop_submission_work() to pass struct scsi_cmnd
related protection into target_submit_cmd_map_sgls() during CDB
dispatch.
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds support for DIF protection into rd_execute_rw() code
for WRITE/READ I/O using sbc_dif_verify_[write,read]() logic.
It also adds rd_get_prot_table() for locating protection SGLs
assoicated with the ramdisk backend device.
v2 changes:
- Make rd_execute_rw() to u32 sectors count instead of sector_t
- Drop SCF_PROT usage
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds rd_build_prot_space() + rd_release_prot_space() logic
to setup + release protection information scatterlists.
It also adds rd_init_prot() + rd_free_prot() se_subsystem_api
callbacks used by target core code for setup + release of
protection information.
v2 changes:
- Drop unused sg_table from rd_release_prot_space (Wei)
- Drop rd_release_prot_space call from rd_free_device
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch refactors rd_build_device_space() + rd_release_device_space()
into rd_allocate_sgl_table() + rd_release_device_space() so that they
may be used seperatly for setup + release of protection information
scatterlists.
Also add explicit memset of pages within rd_allocate_sgl_table() based
upon passed 'init_payload' value.
v2 changes:
- Drop unused sg_table from rd_release_device_space (Wei)
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds support for DIF protection into fd_execute_rw() code
for WRITE/READ I/O using sbc_dif_verify_[write,read]() logic.
It adds fd_do_prot_rw() for handling interface with FILEIO PI, and
uses a locally allocated fd_prot->prot_buf + fd_prot->prot_sg for
interacting with SBC DIF verify emulation code.
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds support for DIF protection init/format support into
the FILEIO backend.
It involves using a seperate $FILE.protection for storing PI that is
opened via fd_init_prot() using the common pi_prot_type attribute.
The actual formatting of the protection is done via fd_format_prot()
using the common pi_prot_format attribute, that will populate the
initial PI data based upon the currently configured pi_prot_type.
Based on original FILEIO code from Sagi.
v1 changes:
- Fix sparse warnings in fd_init_format_buf (Fengguang)
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds blk_integrity passthrough support for block_device
backends using IBLOCK.
This includes iblock_alloc_bip() + setup of bio_integrity_payload
information that attaches to the leading struct bio once bio_list
is populated during fast-path iblock_execute_rw() I/O dispatch.
It also updates setup in iblock_configure_device() to detect modes
of protection + se dev->dev_attrib.pi_prot_type accordingly, along
with creating required bio_set integrity mempools.
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds support to target_submit_cmd_map_sgls() for
accepting 'sgl_prot' + 'sgl_prot_count' parameters for
DIF protection information.
Note the passed parameters are stored at se_cmd->t_prot_sg
and se_cmd->t_prot_nents respectively.
Also, update tcm_loop and vhost-scsi fabrics usage of
target_submit_cmd_map_sgls() to take into account the
new parameters.
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds support for exposing DIF protection device
attributes via configfs. This includes:
pi_prot_type: Protection Type (0, 1, 3 currently support)
pi_prot_format: Protection Format Operation (FILEIO only)
Within se_dev_set_pi_prot_type() it also adds the se_subsystem_api
device callbacks to setup per device protection information.
v2 changes:
- Drop pi_guard_type + pi_prot_version related code (MKP)
- Add pi_prot_format logic (Sagi)
- Add ->free_prot callback in target_free_device
- Add hw_pi_prot_type read-only attribute
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch updates spc_modesense_control() to set the Application
Tag Owner (ATO) bit when when DIF emulation is enabled by the
backend device.
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch updates sbc_emulate_readcapacity_16() to set
P_TYPE and PROT_EN bits when DIF emulation is enabled by
the backend device.
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch updates spc_emulate_evpd_86() (extended INQUIRY) to
report GRD_CHK (Guard Check) and REF_CHK (Reference Check) bits
when DIF emulation is enabled by the backend device.
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch updates spc_emulate_inquiry_std() to set the
PROTECT bit when DIF emulation is enabled by the backend
device.
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds support for DIF read/write verify emulation
for TARGET_DIF_TYPE1_PROT + TARGET_DIF_TYPE3_PROT operation.
This includes sbc_dif_verify_write() + sbc_dif_verify_read()
calls accessable by backend drivers to perform DIF verify
for SGL based data and protection information.
Also included is sbc_dif_copy_prot() logic to copy protection
information to/from backend provided protection SGLs.
Based on scsi_debug.c DIF TYPE1+TYPE3 emulation.
v2 changes:
- Select CRC_T10DIF for TARGET_CORE in Kconfig (Fengguang)
- Drop IP checksum logic from sbc_dif_v1_verify (MKP)
- Fix offset on app_tag = 0xffff in sbc_dif_verify_read()
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds sbc_check_prot() for performing various DIF
related CDB sanity checks, along with setting cmd->prot_type
once sanity checks have passed.
Also, add calls in sbc_parse_cdb() for READ_[10,12,16] +
WRITE_[10,12,16] to perform DIF sanity checking.
v2 changes:
- Make sbc_check_prot defined as static (Fengguang + Wei)
- Remove unprotected READ/WRITE warning (mkp)
- Populate cmd->prot_type + friends (Sagi)
- Drop SCF_PROT usage
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds support for DIF related CHECK_CONDITION ASC/ASCQ
exception cases into transport_send_check_condition_and_sense().
This includes:
LOGICAL BLOCK GUARD CHECK FAILED
LOGICAL BLOCK APPLICATION TAG CHECK FAILED
LOGICAL BLOCK REFERENCE TAG CHECK FAILED
that used by DIF TYPE1 and TYPE3 failure cases.
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts the temporary buffer in spc_emulate_inquiry() to
use dynamically allocated memory, instead of local stack memory.
Also bump SE_INQUIRY_BUF up to 1024 bytes to be safe when handling
multiple large SCSI name descriptors for EVPD=0x83.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
When a writing to a command-provided buffer we need to ensure
that we're not writing past the end of it.
At the same time we need to continue processing as typically
the final data length (ie the required size of the buffer)
need to be returned.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Mark functions ft_tpg_alloc_fabric_acl(), ft_register_configfs() and
ft_deregister_configfs() as static in tcm_fc/tfc_conf.c because they are
not used outside this file.
This eliminates the following warnings in tcm_fc/tfc_conf.c:
drivers/target/tcm_fc/tfc_conf.c:270:21: warning: no previous prototype for ‘ft_tpg_alloc_fabric_acl’ [-Wmissing-prototypes]
drivers/target/tcm_fc/tfc_conf.c:555:5: warning: no previous prototype for ‘ft_register_configfs’ [-Wmissing-prototypes]
drivers/target/tcm_fc/tfc_conf.c:602:6: warning: no previous prototype for ‘ft_deregister_configfs’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Mark functions tcm_loop_make_naa_tpg(), tcm_loop_drop_naa_tpg(),
tcm_loop_make_scsi_hba() and tcm_loop_drop_scsi_hba() as static in
loopback/tcm_loop.c because they are not used outside this file.
This eliminates the following warning in loopback/tcm_loop.c:
drivers/target/loopback/tcm_loop.c:1231:25: warning: no previous prototype for ‘tcm_loop_make_naa_tpg’ [-Wmissing-prototypes]
drivers/target/loopback/tcm_loop.c:1276:6: warning: no previous prototype for ‘tcm_loop_drop_naa_tpg’ [-Wmissing-prototypes]
drivers/target/loopback/tcm_loop.c:1308:16: warning: no previous prototype for ‘tcm_loop_make_scsi_hba’ [-Wmissing-prototypes]
drivers/target/loopback/tcm_loop.c:1378:6: warning: no previous prototype for ‘tcm_loop_drop_scsi_hba’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Mark function iblock_get_write_cache() as static in target_core_iblock.c
because it is not used outside this file.
This eliminates the following warning in target_core_iblock.c:
drivers/target/target_core_iblock.c:766:6: warning: no previous prototype for ‘iblock_get_write_cache’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Move prototype declaration of function
spc_parse_naa_6h_vendor_specific() from target_core_xcopy.c to header
file target_core_pr.h because it is used by more than one file.
This eliminates the following warning in target_core_spc.c:
drivers/target/target_core_spc.c:138:6: warning: no previous prototype for ‘spc_parse_naa_6h_vendor_specific’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Referrals need an LBA map, which needs to be kept
consistent across all target port groups. So
instead of tying the map to the target port groups
I've implemented a single attribute containing the
entire map.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Add infrastructure for referrals.
v2 changes:
- Fix unsigned long long division in core_alua_state_lba_dependent on
32-bit (Fengguang + Chen + Hannes)
- Fix compile warning in core_alua_state_lba_dependent (nab)
- Convert segment_* + sectors variables in core_alua_state_lba_dependent
to u64 (Hannes)
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJSwLfoAAoJEHm+PkMAQRiGi6QH/1U1B7lmHChDTw3jj1lfm9gA
189Si4QJlnxFWCKHvKEL+pcaVuACU+aMGI8+KyMYK4/JfuWVjjj5fr/SvyHH2/8m
LdSK8aHMhJ46uBS4WJ/l6v46qQa5e2vn8RKSBAyKm/h4vpt+hd6zJdoFrFai4th7
k/TAwOAEHI5uzexUChwLlUBRTvbq4U8QUvDu+DeifC8cT63CGaaJ4qVzjOZrx1an
eP6UXZrKDASZs7RU950i7xnFVDQu4PsjlZi25udsbeiKcZJgPqGgXz5ULf8ZH8RQ
YCi1JOnTJRGGjyIOyLj7pyB01h7XiSM2+eMQ0S7g54F2s7gCJ58c2UwQX45vRWU=
=/4/R
-----END PGP SIGNATURE-----
Merge tag 'v3.13-rc6' into for-3.14/core
Needed to bring blk-mq uptodate, since changes have been going in
since for-3.14/core was established.
Fixup merge issues related to the immutable biovec changes.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Conflicts:
block/blk-flush.c
fs/btrfs/check-integrity.c
fs/btrfs/extent_io.c
fs/btrfs/scrub.c
fs/logfs/dev_bdev.c
lun->lun_ref is also initialized in core_tpg_post_addlun, so it doesn't
need to be done in core_tpg_setup_virtual_lun0.
(nab: Drop left-over percpu_ref_cancel_init in failure path)
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch allows FILEIO to update hw_max_sectors based on the current
max_bytes_per_io. This is required because vfs_[writev,readv]() can accept
a maximum of 2048 iovecs per call, so the enforced hw_max_sectors really
needs to be calculated based on block_size.
This addresses a >= v3.5 bug where block_size=512 was rejecting > 1M
sized I/O requests, because FD_MAX_SECTORS was hardcoded to 2048 for
the block_size=4096 case.
(v2: Use max_bytes_per_io instead of ->update_hw_max_sectors)
Reported-by: Henrik Goldman <hg@x-formation.com>
Cc: <stable@vger.kernel.org> #3.5+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
When shutting down a target there is a race condition between
iscsit_del_np() and __iscsi_target_login_thread().
The latter sets the thread pointer to NULL, and the former
tries to issue kthread_stop() on that pointer without any
synchronization.
This patch moves the np->np_thread NULL assignment into
iscsit_del_np(), after kthread_stop() has completed. It also
removes the signal_pending() + np_state check, and only
exits when kthread_should_stop() is true.
Reported-by: Hannes Reinecke <hare@suse.de>
Cc: <stable@vger.kernel.org> #3.12+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We should be including a descriptor referring to the target device
to allow identification of different TCM instances.
(nab: Bump SE_INQUIRY_BUF to 1024 bytes to handle 2x 256 byte SCSI names)
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
scsi_name_len in spc_emulate_evpd_83 is calculated twice, with
the results of the first calculation discarded. So remove it.
And check for the maximum allowed length, too.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Use a workqueue for processing ALUA state transitions; this allows
us to process implicit delay properly.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
During state transition we should be storing both the original
and the pending state.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We should only allocate ALUA metadata if we're actually going
to write them.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
As we now can modify the list of supported states we need to
validate the requested ALUA state when doing a state transition.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
"pre" is really an allocation function. The only time it isn't called is
for virtual_lun0, which is statically allocated. Renaming that to "alloc"
lets the other function not need to be "post", and just be called
core_tpg_add_lun.
(nab: fix minor applying fuzz in core_tpg_setup_virtual_lun0)
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
It's clearer to refer to pointers to the struct se_lun as "lun" and the
actual number itself as "unpacked_lun".
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Allocating an array of pointers, not the objects themselves. These two
sites now match all the other sites.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
See target_stat_setup_port_default_groups, we need a 4 element array.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes special case handling for ISCSI_OP_SCSI_CMD
where an initiator sends a zero length Expected Data Transfer
Length (EDTL), but still sets the WRITE and/or READ flag bits
when no payload transfer is requested.
Many, many moons ago two special cases where added for an ancient
version of ESX that has long since been fixed, so instead of adding
a new special case for the reported bug with a Broadcom 57800 NIC,
go ahead and always strip off the incorrect WRITE + READ flag bits.
Also, avoid sending a reject here, as RFC-3720 does mandate this
case be handled without protocol error.
Reported-by: Witold Bazakbal <865perl@wp.pl>
Tested-by: Witold Bazakbal <865perl@wp.pl>
Cc: <stable@vger.kernel.org> #3.1+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Commit 04f3b31bff ("iscsi-target: Convert iscsi_session statistics to
atomic_long_t") removed the updating of these fields in iscsi (the only
fabric driver that ever touched these counters), and the core has no way
to report or otherwise use the values. Remove the last remnants of
these counters.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The iSCSI CHAP auth parameters are already copied with respect for
the destination buffer size. Return -EINVAL instead of silently
truncating the input.
Signed-off-by: Eric Seppanen <eric@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull SCSI target updates from Nicholas Bellinger:
"Things have been quiet this round with mostly bugfixes, percpu
conversions, and other minor iscsi-target conformance testing changes.
The highlights include:
- Add demo_mode_discovery attribute for iscsi-target (Thomas)
- Convert tcm_fc(FCoE) to use percpu-ida pre-allocation
- Add send completion interrupt coalescing for ib_isert
- Convert target-core to use percpu-refcounting for se_lun
- Fix mutex_trylock usage bug in iscsit_increment_maxcmdsn
- tcm_loop updates (Hannes)
- target-core ALUA cleanups + prep for v3.14 SCSI Referrals support (Hannes)
v3.14 is currently shaping to be a busy development cycle in target
land, with initial support for T10 Referrals and T10 DIF currently on
the roadmap"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (40 commits)
iscsi-target: chap auth shouldn't match username with trailing garbage
iscsi-target: fix extract_param to handle buffer length corner case
iscsi-target: Expose default_erl as TPG attribute
target_core_configfs: split up ALUA supported states
target_core_alua: Make supported states configurable
target_core_alua: Store supported ALUA states
target_core_alua: Rename ALUA_ACCESS_STATE_OPTIMIZED
target_core_alua: spellcheck
target core: rename (ex,im)plict -> (ex,im)plicit
percpu-refcount: Add percpu-refcount.o to obj-y
iscsi-target: Do not reject non-immediate CmdSNs exceeding MaxCmdSN
iscsi-target: Convert iscsi_session statistics to atomic_long_t
target: Convert se_device statistics to atomic_long_t
target: Fix delayed Task Aborted Status (TAS) handling bug
iscsi-target: Reject unsupported multi PDU text command sequence
ib_isert: Avoid duplicate iscsit_increment_maxcmdsn call
iscsi-target: Fix mutex_trylock usage in iscsit_increment_maxcmdsn
target: Core does not need blkdev.h
target: Pass through I/O topology for block backstores
iser-target: Avoid using FRMR for single dma entry requests
...
In iSCSI negotiations with initiator CHAP enabled, usernames with
trailing garbage are permitted, because the string comparison only
checks the strlen of the configured username.
e.g. "usernameXXXXX" will be permitted to match "username".
Just check one more byte so the trailing null char is also matched.
Signed-off-by: Eric Seppanen <eric@purestorage.com>
Cc: <stable@vger.kernel.org> #3.1+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
extract_param() is called with max_length set to the total size of the
output buffer. It's not safe to allow a parameter length equal to the
buffer size as the terminating null would be written one byte past the
end of the output buffer.
Signed-off-by: Eric Seppanen <eric@purestorage.com>
Cc: <stable@vger.kernel.org> #3.1+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch exposes default_erl as a TPG attribute so that it may be
set TPG wide in demo-mode, but still allow the existing NodeACL
attribute to be overridden on a per initiator basis.
Reported-by: Arshad Hussain <arshad.hussain@calsoftinc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Split up the various ALUA states into individual attributes to
make parsing easier and adhere to the one value per attribute
sysfs principle.
(nab: Convert strict_strtoul -> kstrtoul usage)
Signed-off-by: Hannes Reinecke <hare@suse.de>
The supported ALUA states might be different for individual
devices, so store it in a separate field.
(nab: Remove unnecessary line continuation)
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Rename ALUA_ACCESS_STATE_OPTMIZED to
ALUA_ACCESS_STATE_OPTIMIZED.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes iscsit_sequence_cmd() logic to no longer reject
non-immediate CmdSNs that exceed MaxCmdSN with a protocol error,
but instead silently ignore them.
This is done to correctly follow RFC-3720 Section 3.2.2.1:
For non-immediate commands, the CmdSN field can take any
value from ExpCmdSN to MaxCmdSN inclusive. The target MUST silently
ignore any non-immediate command outside of this range or non-
immediate duplicates within the range.
Reported-by: Santosh Kulkarni <santosh.kulkarni@calsoftinc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts a handful of iscsi_session statistics to type
atomic_long_t, instead of using iscsi_session->session_stats_lock
when incrementing these values.
More importantly, go ahead and drop the spinlock usage within
iscsit_setup_scsi_cmd(), iscsit_check_dataout_hdr(),
iscsit_send_datain(), and iscsit_build_rsp_pdu() fast-path code.
(Squash in Roland's target: Remove write-only stats fields and lock
from struct se_node_acl)
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts the handful of se_device statistics to type
atomic_long_t, instead of using se_device->stats_lock when
incrementing these values.
More importantly, go ahead and drop the spinlock usage within
transport_lookup_cmd_lun() fast-path code.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a bug in delayed Task Aborted Status (TAS) handling,
where transport_send_task_abort() was not returning for the case
when the se_tfo->write_pending() callback indicated that last fabric
specific WRITE PDU had not yet been received.
It also adds an explicit cmd->scsi_status = SAM_STAT_TASK_ABORTED
assignment within transport_check_aborted_status() to avoid the case
where se_tfo->queue_status() is called when the SAM_STAT_TASK_ABORTED
assignment + ->queue_status() in transport_send_task_abort() does not
occur once SCF_SENT_DELAYED_TAS has been set.
Cc: <stable@vger.kernel.org> #3.2+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a check to reject text commands with F_BIT=0 ||
C_BIT=1, as multi PDU text command sequences are currently
unsupported.
This avoids the case where a text command received with F_BIT=0,
was generating a text response with F_BIT=1 which is a protocol
error according to RFC-3720 Section 10.11.1.
Reported-by: Arshad Hussain <arshad.hussain@calsoftinc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a >= v3.10 regression bug with mutex_trylock() usage
within iscsit_increment_maxcmdsn(), that was originally added to allow
for a special case where ->cmdsn_mutex was already held from the
iscsit_execute_cmd() exception path for ib_isert.
When !mutex_trylock() was occuring under contention during normal RX/TX
process context codepaths, the bug was manifesting itself as the following
protocol error:
Received CmdSN: 0x000fcbb7 is greater than MaxCmdSN: 0x000fcbb6, protocol error.
Received CmdSN: 0x000fcbb8 is greater than MaxCmdSN: 0x000fcbb6, protocol error.
This patch simply avoids the direct ib_isert callback in lio_queue_status()
for the special iscsi_execute_cmd() exception cases, that allows the problematic
mutex_trylock() usage in iscsit_increment_maxcmdsn() to go away.
Reported-by: Moussa Ba <moussaba@micron.com>
Tested-by: Moussa Ba <moussaba@micron.com>
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Target core does not depend on the block layer, only backstores that
use the block layer do.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In addition to block size (already implemented), passing through
alignment offset, logical-to-phys block exponent, I/O granularity and
optimal I/O length will allow initiators to properly handle layout on
LUNs with 4K block sizes.
Tested with various weird values via scsi_debug module.
One thing to look at with this patch is the new block limits values --
instead of granularity 1 optimal 8192, Lio will now be returning whatever
the block device says, which may affect performance.
Signed-off-by: Andy Grover <agrover@redhat.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a se_device->xcopy_lun that is used for local
copy offload I/O, instead of allocating + initializing a pseudo
se_lun for each received EXTENDED_COPY operation.
Also, move declaration of struct se_lun + struct se_port_stat_grps
ahead of struct se_device.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now with percpu refcounting for se_lun in place, go ahead and drop
the legacy per se_cmd accounting for se_lun shutdown.
This includes __transport_clear_lun_from_sessions(), the associated
transport_lun_wait_for_tasks() logic, along with a handful of now
unused se_cmd structure members and ->transport_state bits.
Cc: Kent Overstreet <kmo@daterainc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds percpu refcounting for se_lun access that allows the
association of an se_lun + se_cmd in transport_lookup_cmd_lun() to
occur without an extra list_head for tracking outstanding I/O during
se_lun shutdown.
This effectively changes se_lun shutdown logic to wait for outstanding
I/O percpu references to complete in transport_lun_remove_cmd() using
se_lun->lun_ref_comp, instead of explicitly draining the per se_lun
command list and waiting for individual se_cmd descriptor processing
to complete.
Cc: Kent Overstreet <kmo@daterainc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes iscsit_check_dataout_hdr() to no longer generate
REJECTs for zero-length DataOUTs, and instead simply ignore these
requests.
This follows RFC-3720, Section 10.7.7. DataSegmentLength
"This is the data payload length of a SCSI Data-In or SCSI Data-Out PDU.
The sending of 0 length data segments should be avoided, but initiators
and targets MUST be able to properly receive 0 length data segments."
Reported-by: Santosh Kulkarni <santosh.kulkarni@calsoftinc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In case of error, the function scsi_host_lookup() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds an explicit check + failure for XCOPY I/O to source +
destination devices with a non-matching block_size.
This limitiation is currently due to the fact that the scatterlist
memory allocated for the XCOPY READ operation is passed zero-copy
to the XCOPY WRITE operation.
Reported-by: Thomas Glanzmann <thomas@glanzmann.de>
Reported-by: Douglas Gilbert <dgilbert@interlog.com>
Cc: Thomas Glanzmann <thomas@glanzmann.de>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds the missing non-zero se_cmd->scsi_status check required
for local XCOPY I/O within target_xcopy_issue_pt_cmd() to signal an
exception case failure.
This will trigger the generation of SAM_STAT_CHECK_CONDITION status
from within target_xcopy_do_work() process context code.
Reported-by: Thomas Glanzmann <thomas@glanzmann.de>
Reported-by: Douglas Gilbert <dgilbert@interlog.com>
Cc: Thomas Glanzmann <thomas@glanzmann.de>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds the missing xcopy_pt_cmd->sense_buffer[] required for
correctly handling CHECK_CONDITION exceptions within the locally
generated XCOPY I/O path.
Also update target_xcopy_read_source() + target_xcopy_setup_pt_cmd()
to pass this buffer into transport_init_se_cmd() to correctly setup
se_cmd->sense_buffer.
Reported-by: Thomas Glanzmann <thomas@glanzmann.de>
Reported-by: Douglas Gilbert <dgilbert@interlog.com>
Cc: Thomas Glanzmann <thomas@glanzmann.de>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
If demo_mode_discovery=0 and generate_node_acls=0 (demo mode dislabed) do
not return TargetName+TargetAddress unless a NodeACL exists.
Signed-off-by: Thomas Glanzmann <thomas@glanzmann.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Export symbol core_tpg_check_initiator_node_acl and move prototype from the
private drivers/target/target_core_internal.h to the public
include/target/target_core_fabric.h
Signed-off-by: Thomas Glanzmann <thomas@glanzmann.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Add a new TPG attribute demo_mode_discovery which is enabled by default.
Signed-off-by: Thomas Glanzmann <thomas@glanzmann.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Implement target reset by resetting the transport status.
(nab: Remove unused ret in tcm_loop_target_reset)
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Implement TCQ support, which enables us to do proper command
abort, too.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Add attribute 'transport_status' to simulate link failure.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
These just want to return a pointer instead of a value, but are otherwise
the same.
ISCSI_TPG_LUN macro was unused.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
These are all straightforward.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Remove a lingering macro that just hid a dereference.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Per SBC-3, since we report ANC_SUP==0 in VPD page B2h, we need to return
an error (ILLEGAL REQUEST/INVALID FIELD IN CDB) for all WRITE SAME
requests with ANCHOR==1.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch rejects EXTENDED_COPY when the emulate_3pc attribute has
been explicitly disabled for the receiving device.
It also adds a similar check in target_xcopy_locate_se_dev_e4() to
ignore these devices when doing a search based upon the identifier
WWN provided by EXTENDED_COPY parameter list target descriptors.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes target_do_xcopy() to allow processing of non-zero
ListIDs in EXTENDED_COPY parameter list data, instead of returning
CHECK_CONDITION status.
As the copy offload implementation reports SNLID=1 (Supports No ListID)
in OPERATING PARAMETERS, any ListID value presented by the client is
currently ignored.
Also, properly extract list_id_usage for informational purposes.
Reported-by: Thomas Glanzmann <thomas@glanzmann.de>
Reported-by: Douglas Gilbert <dgilbert@interlog.com>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes target_do_xcopy() to properly return
TCM_INVALID_PARAMETER_LIST instead of TCM_INVALID_CDB_FIELD
for failures related to the EXTENDED_COPY parameter list parsing.
Also, move struct xcopy_op allocation ahead of kmapping to
handle the special TCM_OUT_OF_RESOURCES case.
Reported-by: Thomas Glanzmann <thomas@glanzmann.de>
Reported-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch bumps the default number of tags allocated per session by
iscsi-target via transport_alloc_session_tags() -> percpu_ida_init()
by another (tag_num / 2).
This is done to take into account the tags waiting to be acknowledged
and released in iscsit_ack_from_expstatsn(), but who's number are not
directly limited by the CmdSN Window queue_depth being enforced by
the target.
Using a larger value here is also useful to prevent percpu_ida_alloc()
from having to steal tags from other CPUs when no tags are available
on the local CPU, while waiting for unacknowledged tags to be released.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts iscsit_ack_from_expstatsn() to populate a local
ack_list of commands, and call iscsit_free_cmd() directly from RX
thread context, instead of using iscsit_add_cmd_to_immediate_queue()
to queue the acknowledged commands to be released from TX thread
context.
It is helpful to release the acknowledge commands as quickly as
possible, along with the associated percpu_ida tags, in order to
prevent percpu_ida_alloc() from having to steal tags from other
CPUs while waiting for iscsit_free_cmd() to happen from TX thread
context.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes transport_generic_free_cmd() to only wait_for_tasks
when shutdown=true is passed to iscsit_free_cmd().
With the advent of >= v3.10 iscsi-target code using se_cmd->cmd_kref,
the extra wait_for_tasks with shutdown=false is unnecessary, and may
end up causing an extra context switch when releasing WRITEs.
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses a bug for backends such as IBLOCK that perform
asynchronous completion via transport_complete_cmd(), that will call
target_complete_failure_work() -> transport_generic_request_failure(),
upon exception status and invoke cmd->transport_complete_callback()
-> compare_and_write_callback() incorrectly during the failure case.
It adds a check for a non zero se_cmd->scsi_status within the first
invocation of compare_and_write_callback(), and will jump to out plus
up se_device->caw_sem before exiting the callback.
Reported-by: Thomas Glanzmann <thomas@glanzmann.de>
Tested-by: Thomas Glanzmann <thomas@glanzmann.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses a bug when compare_and_write_callback() invoked from
target_complete_ok_work() hits an failure from __target_execute_cmd() ->
cmd->execute_cmd(), that ends up calling transport_generic_request_failure()
-> compare_and_write_post(), thus causing SCF_COMPARE_AND_WRITE_POST to
incorrectly be set.
The result of this bug is that target_complete_ok_work() no longer hits
the if (!rc && !(cmd->se_cmd_flags & SCF_COMPARE_AND_WRITE_POST) check
that forces an immediate return, and instead double completes the se_cmd
in question, triggering an OOPs in the process.
This patch changes compare_and_write_post() to only set this bit when a
failure has not already occured to ensure the immediate return from within
target_complete_ok_work(), and thus allow transport_generic_request_failure()
to handle the sending of the CHECK_CONDITION exception status.
Reported-by: Thomas Glanzmann <thomas@glanzmann.de>
Tested-by: Thomas Glanzmann <thomas@glanzmann.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch resets se_cmd->data_length for COMPARE_AND_WRITE emulation
within sbc_compare_and_write() to NoLB * block_size in order to address
a bug with FILEIO backends where a I/O failure will occur when data_length
does not match the I/O size being actually dispatched for the individual
per block READs + WRITEs.
This is done late enough in sbc_compare_and_write() after the memory
allocations have occured in transport_generic_new_cmd() to not cause
any unwanted side-effects.
Reported-by: Thomas Glanzmann <thomas@glanzmann.de>
Tested-by: Thomas Glanzmann <thomas@glanzmann.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts tcm_fc to use transport_init_session_tags()
pre-allocation logic for struct ft_cmd descriptors using per-cpu
session tag pooling in order to effectively avoid memory allocation
+ release for each received I/O.
It adds percpu_ida_alloc() in ft_recv_cmd() to obtain an tag and
locate ft_cmd from se_sess->sess_cmd_map[], and percpu_ida_free()
in ft_free_cmd() to release the tag based upon se_cmd->map_tag id.
It also uses a TCM_FC_DEFAULT_TAGS value of 512, that puts the
per se_sess->sess_cmd_map allocation at ~360K on 64-bit.
v2 changes:
- Handle possible tag < 0 failure with GFP_ATOMIC
Cc: Mark Rustad <mark.d.rustad@intel.com>
Cc: Robert Love <robert.w.love@intel.com>
Cc: Kent Overstreet <kmo@daterainc.com>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
This patch changes transport_alloc_session_tags() to fall back to
use vzalloc when kzalloc fails for big tag_num that end up generating
larger order allocations.
Also use is_vmalloc_addr() in transport_alloc_session_tags() failure
path, and normal transport_free_session() path to determine when
vfree() needs to be called instead of kfree().
v2 changes:
- Use __GFP_NOWARN | __GFP_REPEAT for sess_cmd_map kzalloc (mst)
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Asias He <asias@redhat.com>
Cc: Kent Overstreet <kmo@daterainc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes up an incorrect assignment for xop->dbl within
target_xcopy_parse_segdesc_02() code, as reported by Coverity here:
http://marc.info/?l=linux-kernel&m=137936416618490&w=2
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull SCSI target updates from Nicholas Bellinger:
"Lots of activity again this round for I/O performance optimizations
(per-cpu IDA pre-allocation for vhost + iscsi/target), and the
addition of new fabric independent features to target-core
(COMPARE_AND_WRITE + EXTENDED_COPY).
The main highlights include:
- Support for iscsi-target login multiplexing across individual
network portals
- Generic Per-cpu IDA logic (kent + akpm + clameter)
- Conversion of vhost to use per-cpu IDA pre-allocation for
descriptors, SGLs and userspace page pointer list
- Conversion of iscsi-target + iser-target to use per-cpu IDA
pre-allocation for descriptors
- Add support for generic COMPARE_AND_WRITE (AtomicTestandSet)
emulation for virtual backend drivers
- Add support for generic EXTENDED_COPY (CopyOffload) emulation for
virtual backend drivers.
- Add support for fast memory registration mode to iser-target (Vu)
The patches to add COMPARE_AND_WRITE and EXTENDED_COPY support are of
particular significance, which make us the first and only open source
target to support the full set of VAAI primitives.
Currently Linux clients are lacking upstream support to actually
utilize these primitives. However, with server side support now in
place for folks like MKP + ZAB working on the client, this logic once
reserved for the highest end of storage arrays, can now be run in VMs
on their laptops"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (50 commits)
target/iscsi: Bump versions to v4.1.0
target: Update copyright ownership/year information to 2013
iscsi-target: Bump default TCP listen backlog to 256
target: Fix >= v3.9+ regression in PR APTPL + ALUA metadata write-out
iscsi-target; Bump default CmdSN Depth to 64
iscsi-target: Remove unnecessary wait_for_completion in iscsi_get_thread_set
iscsi-target: Add thread_set->ts_activate_sem + use common deallocate
iscsi-target: Fix race with thread_pre_handler flush_signals + ISCSI_THREAD_SET_DIE
target: remove unused including <linux/version.h>
iser-target: introduce fast memory registration mode (FRWR)
iser-target: generalize rdma memory registration and cleanup
iser-target: move rdma wr processing to a shared function
target: Enable global EXTENDED_COPY setup/release
target: Add Third Party Copy (3PC) bit in INQUIRY response
target: Enable EXTENDED_COPY setup in spc_parse_cdb
target: Add support for EXTENDED_COPY copy offload emulation
target: Avoid non-existent tg_pt_gp_mem in target_alua_state_check
target: Add global device list for EXTENDED_COPY
target: Make helpers non static for EXTENDED_COPY command setup
target: Make spc_parse_naa_6h_vendor_specific non static
...
Update copyright ownership/year information for target-core,
loopback, iscsi-target, tcm_qla2xx, vhost and iser-target.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch bumps the default TCP listen backlog within iscsit_setup_np()
from 5 to 256, in order to reduce the overall latency caused by a small
backlog with 100's of simultaneous login attempts directed to the same
single network portal.
Also add a ISCSIT_TCP_BACKLOG macro in iscsi_target_core.h.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a >= v3.9+ regression in __core_scsi3_write_aptpl_to_file()
+ core_alua_write_tpg_metadata() write-out, where a return value of -EIO was
incorrectly being returned upon success.
This bug was originally introduced in:
commit 0e9b10a90f
Author: Al Viro <viro@zeniv.linux.org.uk>
Date: Sat Feb 23 15:22:43 2013 -0500
target: writev() on single-element vector is pointless
However, given that the return of core_scsi3_update_and_write_aptpl()
was not used to determine if a command should be returned with non GOOD
status, this bug was not being triggered in PR logic until v3.11-rc1 by
commit:
commit 459f213ba1
Author: Andy Grover <agrover@redhat.com>
Date: Thu May 16 10:41:02 2013 -0700
target: Allocate aptpl_buf inside update_and_write_aptpl()
So, go ahead and only return -EIO if kernel_write() returned a
negative value.
Reported-by: Gera Kazakov <gkazakov@msn.com>
Signed-off-by: Gera Kazakov <gkazakov@msn.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Andy Grover <agrover@redhat.com>
Cc: stable@vger.kernel.org # 3.9+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch bumps the default TA_DEFAULT_CMDSN_DEPTH from 16 -> 64,
which is closer to a sane default for larger pipes @ 10 Gb/sec
with traditional iSCSI, or @ 40/56 Gb/sec Ethernet/Infiniband with
iSCSI Extentions for RDMA.
There is really no downside to increasing this default value for
1 Gb/sec.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch removes an unnecessary wait_for_completion within
iscsi_get_thread_set(), that would wait for 1 second before
trying to obtain an inactive struct iscsi_thread_set from
iscsi_get_ts_from_inactive_list().
Since iscsi_allocate_thread_sets() will already be adding the
newly allocated iscsi_thread_set to the inactive list directly,
there is no need to wait here.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch removes the iscsi_thread_set->[rx,tx]_post_start_comp that
was originally used synchronize startup between rx and tx threads within
a single thread_set.
Instead, use a single ->ts_activate_sem in iscsi_activate_thread_set()
to wait for both processes to awake in the RX/TX pre handlers.
Also, go ahead and refactor thread_set deallocate code into a common
iscsi_deallocate_thread_one(), and update iscsi_deallocate_thread_sets()
and iscsi_deallocate_extra_thread_sets() use this code
v3 changes:
- Make iscsi_deallocate_thread_one defined as static (Fengguang)
v2 changes:
- Set ISCSI_THREAD_SET_ACTIVE before calling complete in
iscsi_activate_thread_set
- Protect ts->conn sanity checks with ->ts_state_lock in
RX/TX pre handlers
- Add ->ts_activate_sem to save extra context switches per
iscsi_activate_thread_set() call.
- Refactor thread_set shutdown into iscsi_deallocate_thread_one()
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses an long standing race in iscsi_[rx,tx]_thread_pre_handler()
use of flush_signals(), and between iscsi_deallocate_extra_thread_sets() setting
ISCSI_THREAD_SET_DIE before calling kthread_stop().
It addresses the issue by both holding ts_state_lock before calling send_sig()
in iscsi_deallocate_extra_thread_sets(), as well as only calling flush_signals()
when ts->status != ISCSI_THREAD_SET_DIE within iscsi_[rx,tx]_thread_pre_handler()
code.
v2 changes:
- Add explicit complete(&ts->[rx,tx]_start_comp); before kthread_stop() in
iscsi_deallocate_extra_thread_sets()
- Drop left-over send_sig() calls in iscsi_deallocate_extra_thread_sets()
- Add kthread_should_stop() check in iscsi_signal_thread_pre_handler()
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Remove including <linux/version.h> that don't need it.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Add calls to target_xcopy_setup_pt() + target_xcopy_release_pt() to
target_core_init_configfs() and target_core_exit_configfs()
respectively.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Zach Brown <zab@redhat.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
This patch adds the Third Party Copy (3PC) bit to signal support
for EXTENDED_COPY within standard inquiry response data.
Also add emulate_3pc device attribute in configfs (enabled by default)
to allow the exposure of this bit to be disabled, if necessary.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Zach Brown <zab@redhat.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
Setup up the se_cmd->execute_cmd() pointers for EXTENDED_COPY and
RECEIVE_COPY_RESULTS handling within spc_parse_cdb()
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Zach Brown <zab@redhat.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
This patch adds support for EXTENDED_COPY emulation from SPC-3, that
enables full copy offload target support within both a single virtual
backend device, and across multiple virtual backend devices. It also
functions independent of target fabric, and supports copy offload
across multiple target fabric ports.
This implemenation supports both EXTENDED_COPY PUSH and PULL models
of operation, so the actual CDB may be received on either source or
desination logical unit.
For Target Descriptors, it currently supports the NAA IEEE Registered
Extended designator (type 0xe4), which allows the reference of target
ports to occur independent of fabric type using EVPD 0x83 WWNs.
For Segment Descriptors, it currently supports copy from block to
block (0x02) mode.
It also honors any present SCSI reservations of the destination target
port. Note that only Supports No List Identifier (SNLID=1) mode is
supported.
Also included is basic RECEIVE_COPY_RESULTS with service action type
OPERATING PARAMETERS (0x03) required for SNLID=1 operation.
v3 changes:
- Fix incorrect return type in target_do_receive_copy_results()
(Fengguang)
v2 changes:
- Use target_alloc_sgl() instead of transport_generic_get_mem()
- Convert debug output to use pr_debug()
- Convert target_xcopy_parse_target_descriptors() NAA IEEN WWN
dump to use 0x%16phN format specification
- Drop unnecessary xcopy_pt_cmd->xpt_passthrough_wsem, and
associated usage in xcopy_pt_write_pending() and
target_xcopy_issue_pt_cmd()
- Add check for unsupported EXTENDED_COPY(LID4) service action
bits in target_do_xcopy()
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Zach Brown <zab@redhat.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
This patch adds an check for a non-existent port->sep_alua_tg_pt_gp_mem
within target_alua_state_check(), which is not present for internally
dispatched EXTENDED_COPY WRITE I/O to the destination target port.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Zach Brown <zab@redhat.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
EXTENDED_COPY needs to be able to search a global list of devices
based on NAA WWN device identifiers, so add a simple g_device_list
protected by g_device_mutex.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Zach Brown <zab@redhat.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
Both target_alloc_sgl() and transport_generic_map_mem_to_cmd() are
required by EXTENDED_COPY logic when setting up internally dispatched
command descriptors, so go ahead and make both of these non static.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Zach Brown <zab@redhat.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
This patch makes spc_parse_naa_6h_vendor_specific() available to
other target code, which is required by EXTENDED_COPY when comparing
the received NAA WWN device identifer for locating the associated
se_device backend.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Zach Brown <zab@redhat.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
This patch makes the top-level target_core_subsystem array available
to other target code, which is required by EXTENDED_COPY to pin the
backend se_device using configfs_depend_item(), in order to ensure
it can't be removed for the duration of a EXTENDED_COPY operation.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Zach Brown <zab@redhat.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
This patch adds a extra check for SCF_COMPARE_AND_WRITE within
transport_generic_request_failure() to invoke the callback for
compare_and_write_callback() or compare_and_write_done(), in
order to release se_dev->caw_mutex from the generic failure
path.
It also adds to checks within compare_and_write_callback() to
avoid processing when transport_generic_request_failure() occurs
early enough that cmd->t_data_sg or cmd->t_bidi_data_sg have not
been setup yet, nor se_dev->caw_mutex obtained from within
sbc_compare_and_write().
v4 changes:
- Add explicit check for cmd->transport_complete_callback in
transport_generic_request_failure() to handle case where
sbc_compare_and_write()clears callback pointer (Dan Carpenter)
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes target_complete_ok_work() to fall through
after calling the se_cmd->transport_complete_callback() ->
compare_and_write_post() callback, by keying off the existance
of SCF_COMPARE_AND_WRITE_POST.
This is necessary because once SCF_COMPARE_AND_WRITE_POST has
been set by compare_and_write_post(), the SCSI response needs
to be sent via TFO->queue_status().
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
This patch adds support for COMPARE_AND_WRITE emulation on a per block
basis. This logic is used as an atomic test and set primative currently
used by VMWare ESX VAAI for performing array side locking of individual
VMFS extent ownership.
This includes the COMPARE_AND_WRITE CDB parsing within sbc_parse_cdb(),
and does the majority of the work within the compare_and_write_callback()
to perform the verify instance user data comparision, and subsequent
write instance user data I/O submission upon a successfull comparision.
The synchronization is enforced by se_device->caw_sem, that is obtained
before the initial READ I/O submission in sbc_compare_and_write(). The
mutex is then released upon MISCOMPARE in compare_and_write_callback(),
or upon WRITE instance user-data completion in compare_and_write_post().
The implementation currently assumes a single logical block (NoLB=1).
v4 changes:
- Explicitly clear cmd->transport_complete_callback for two failure
cases in sbc_compare_and_write() in order to avoid double unlock
of ->caw_sem in compare_and_write_callback() (Dan Carpenter)
v3 changes:
- Convert se_device->caw_mutex to ->caw_sem
v2 changes:
- Set SCF_COMPARE_AND_WRITE and cmd->execute_cmd() to
sbc_compare_and_write() during setup in sbc_parse_cdb()
- Use sbc_compare_and_write() for initial READ submission with
DMA_FROM_DEVICE
- Reset cmd->execute_cmd() to sbc_execute_rw() for write instance
user-data in compare_and_write_callback()
- Drop SCF_BIDI command flag usage
- Set TRANSPORT_PROCESSING + transport_state flags before write
instance submission, and convert to __target_execute_cmd()
- Prevent sbc_get_size() from being being called twice to
generate incorrect size in sbc_parse_cdb()
- Enforce se_device->caw_mutex synchronization between initial
READ I/O submission, and final WRITE I/O completion.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
This patch adds the MAXIMUM COMPARE AND WRITE LENGTH bit, currently
hardcoded to a single logical block (NoLB=1) within the Block Limits
VPD in spc_emulate_evpd_b0().
Also add emulate_caw device attribute in configfs (enabled by default)
to allow the exposure of this bit to be disabled, if necessary.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
Required by COMPARE_AND_WRITE for write instance user-data
submission, in order to bypass target_execute_cmd() checks.
Reported-by: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
After COMPARE_AND_WRITE completes it's comparision, the WRITE
payload SGLs head expect to be updated to point from the verify
instance of user data, to the write instance of user data.
So for this special case, add transport_reset_sgl_orig() usage
within transport_free_pages() and add se_cmd->t_data_[sg,nents]_orig
members to save the original assignments.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
This patch updates transport_generic_new_cmd() to call target_alloc_sgl()
for SGL + page memory allocation for se_cmd->t_bidi_data_sg.
It also adds the special case for SCF_COMPARE_AND_WRITE to calculate a
different bidi_length based upon se_cmd->t_task_nolb.
Reported-by: Christoph Hellwig <hch@lst.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
This patch refactors transport_generic_get_mem() to target_alloc_sgl()
for accepting **sgl, *nents, length and zero_page as function parameters
in order to be used for both se_cmd->t_data_sg + se_cmd->t_bidi_data_sg
allocations.
Reported-by: Christoph Hellwig <hch@lst.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
Stop keying off se_cmd->t_bidi_data_sg within transport_complete_qf()
+ target_complete_ok_work(), and just use SCF_BIDI instead.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
COMPARE_AND_WRITE expects to be able to send down a DMA_FROM_DEVICE
to obtain the necessary READ payload for comparision against the
first half of the WRITE payload containing the verify user data.
Currently virtual backends expect to internally reference SGLs,
SGL nents, and data_direction, so change IBLOCK, FILEIO and RD
sbc_ops->execute_rw() to accept this values as function parameters.
Also add default sbc_execute_rw() handler for the typical case for
cmd->execute_rw() submission using cmd->t_data_sg, cmd->t_data_nents,
and cmd->data_direction).
v2 Changes:
- Add SCF_COMPARE_AND_WRITE command flag
- Use sbc_execute_rw() for normal cmd->execute_rw() submission
with expected se_cmd members.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
This patch adds TCM_MISCOMPARE_VERIFY (ASC=0x1d, ASCQ=0x00) sense
handling to transport_send_check_condition_and_sense(), which is
required for a COMPARE_AND_WRITE comparision failure.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
This patch adds a sense_reason_t return to ->transport_complete_callback(),
and updates target_complete_ok_work() to invoke the call if necessary to
transport_send_check_condition_and_sense() during the failure case.
Also update xdreadwrite_callback() to use this return value.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
blk_get_request() just returns NULL on error, it doesn't return an
ERR_PTR.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes iscsi-target to use transport_alloc_session_tags()
pre-allocation logic for per-cpu session tag pooling with internal
ida_alloc() + ida_free() calls based upon the saved se_cmd->map_tag id.
This includes tag pool setup based upon per NodeACL queue_depth after
locating se_node_acl in iscsi_target_locate_portal().
Also update iscsit_allocate_cmd() and iscsit_release_cmd() to use
percpu_ida_alloc() and percpu_ida_free() respectively.
v5 changes;
- Convert to percpu_ida.h include
v2 changes:
- Fix bug with SessionType=Discovery in iscsi_target_locate_portal()
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Kent Overstreet <kmo@daterainc.com>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
This command converts iscsi/isert-target to use allocations based on
iscsit_transport->priv_size within iscsit_allocate_cmd(), instead of
using an embedded isert_cmd->iscsi_cmd.
This includes removing iscsit_transport->alloc_cmd() usage, along
with updating isert-target code to use iscsit_priv_cmd().
Also, remove left-over iscsit_transport->release_cmd() usage for
direct calls to iscsit_release_cmd(), and drop the now unused
lio_cmd_cache and isert_cmd_cache.
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Kent Overstreet <kmo@daterainc.com>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
This patch adds lib/idr.c based transport_init_session_tags() logic
that allows fabric drivers to setup a per-cpu se_sess->sess_tag_pool
and associated se_sess->sess_cmd_map for basic tagged pre-allocation
of fabric descriptor sized memory.
v5 changes:
- Convert to percpu_ida.h include
v4 changes:
- Add transport_alloc_session_tags() for fabrics that need early
transport_init_session()
v3 changes:
- Update to percpu-ida usage
Cc: Kent Overstreet <kmo@daterainc.com>
Cc: Asias He <asias@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Asias He <asias@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
There is no need for iscsi_target_do_login_io() anymore in modern code,
so go ahead and call iscsi_target_do_tx_login_io() directly within
iscsi_target_do_login().
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a sock->sk_state_change() -> iscsi_target_sk_state_change()
callback in order to handle transient TCP failures during the login process,
where sock->sk_data_ready() -> iscsi_target_sk_data_ready() may not be
called to release connection resources, and relinquish tpg->np_login_lock
via iscsit_deaccess_np()
It performs the sk->sk_state check using iscsi_target_sk_state_check() to
look for TCP_CLOSE_WAIT + TCP_CLOSE, and invokes schedule_delayed_work() ->
iscsi_target_do_cleanup() to perform the remaining cleanup from process
context.
It adds an explicit sk_state_check to iscsi_target_do_login() in order
to determine a state failure when iscsi_target_sk_state_change() may
not be able to proceed before LOGIN_FLAGS_READY=1 is set.
Also use sk->sk_sndtimeo -> sk->sk_rcvtimeo settings during login to
iscsi_target_set_sock_callbacks(), and revert back post login to use
MAX_SCHEDULE_TIMEOUT in iscsi_target_restore_sock_callbacks().
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds support for login negotiation multi-plexing in
iscsi-target code.
This involves handling the first login request PDU + payload and
login response PDU + payload within __iscsi_target_login_thread()
process context, and then changing struct sock->sk_data_ready()
so that all subsequent exchanges are handled by workqueue process
context, to allow other incoming login requests to be received
in parallel by __iscsi_target_login_thread().
Upon login negotiation completion (or failure), ->sk_data_ready()
is replaced with the original kernel sockets handler saved in
iscsi_conn->orig_data_ready.
v3 changes:
- Convert iscsi_target_sk_data_ready() lock access to
write[lock,unlock]_bh()
- Only clear LOGIN_FLAGS_READ_ACTIVE when iscsi_target_do_login()
returns zero
- Add LOGIN_FLAGS_READY + LOGIN_FLAGS_CLOSED bit checks to
iscsi_target_sk_data_ready()
- Make INIT_DELAYED_WORK() + iscsi_target_set_sock_callbacks() setup
happen earlier by moving from iscsi_target_start_negotiation() into
iscsi_target_locate_portal()
- Set LOGIN_FLAGS_READY bit in iscsi_target_start_negotiation()
after iscsi_target_do_login() returns zero.
v2 changes:
- Add login_timer in iscsi_target_do_login_rx() to avoid
possible endless sleep with MSG_WAITALL for traditional
iscsi-target in certain network configurations.
- Convert lprintk() -> pr_debug()
- Remove forward declarations of iscsi_target_set_sock_callbacks(),
iscsi_target_restore_sock_callbacks() and iscsi_target_sk_data_ready()
- Make iscsi_target_set_sock_callbacks + iscsi_target_restore_sock_callbacks()
static (Fengguang)
- Make iscsi_target_do_login_rx() safe for iser-target w/o conn->sock
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses a v3.11 specific regression where se_cmd->state_list
was being leaked during a fabric WRITE failure, when the fabric releases
an associated se_cmd descriptor before I/O submission occurs, and normal
fast path callbacks have a chance to call target_remove_from_state_list().
It was manifesting with Poison overwritten messages with iscsi-target
once an ImmediateData payload CRC32C failure occured.
This bug was originally introduced during v3.11-rc1 with the following
commit:
commit 0b66818ac6
Author: Nicholas Bellinger <nab@linux-iscsi.org>
Date: Thu Jun 6 01:36:41 2013 -0700
target: Drop unnecessary CMD_T_DEV_ACTIVE check from transport_lun_remove_cmd
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses a potential NULL pointer dereference regression in
iscsit_setup_nop_out() code, specifically for two cases when a solicited
NOPOUT triggers a ISCSI_REASON_PROTOCOL_ERROR reject to be generated.
This is because iscsi_cmd is expected to be NULL for solicited NOPOUT
case before iscsit_process_nop_out() locates the descriptor via TTT
using iscsit_find_cmd_from_ttt().
This regression was originally introduced in:
commit ba15991408
Author: Nicholas Bellinger <nab@linux-iscsi.org>
Date: Wed Jul 3 03:48:24 2013 -0700
iscsi-target: Fix iscsit_add_reject* usage for iser
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a bug in __iscsi_target_login_thread() where an explicit
network portal thread reset ends up leaking the iscsit_transport module
reference, along with the associated iscsi_conn allocation.
This manifests itself with iser-target where a NP reset causes the extra
iscsit_transport reference to be taken in iscsit_conn_set_transport()
during the reset, which prevents the ib_isert module from being unloaded
after the NP thread shutdown has finished.
Cc: stable@vger.kernel.org # v3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses a regression bug within ImmediateData=Yes failure
handling that ends up triggering an OOPs within >= v3.10 iscsi-target
code.
The problem occurs when iscsit_process_scsi_cmd() does the call to
target_put_sess_cmd(), and once again in iscsit_get_immediate_data()
that is triggered during two different cases:
- When iscsit_sequence_cmd() returns CMDSN_LOWER_THAN_EXP, for which
the descriptor state will already have been set to ISTATE_REMOVE
by iscsit_sequence_cmd(), and
- When iscsi_cmd->sense_reason is set, for which iscsit_execute_cmd()
will have already called transport_send_check_condition_and_sense()
to queue the exception response.
It changes iscsit_process_scsi_cmd() to drop the early call, and makes
iscsit_get_immediate_data() call target_put_sess_cmd() from a single
location after dumping the immediate data for the failed command.
The regression was initially introduced in commit:
commit 561bf15892
Author: Nicholas Bellinger <nab@linux-iscsi.org>
Date: Wed Jul 3 03:58:58 2013 -0700
iscsi-target: Fix iscsit_sequence_cmd reject handling for iser
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Odd little issue, found that if you create an IPv6 portal bound to the
IN6ADDR_ANY wildcard address it will accept IPv4 connections (as long as
bindv6only isn't set globally) but respond to SendTargets requests with
an IPv4-mapped IPv6 address.
Example over loopback:
In targetcli create a wildcard IPv6 portal
/iscsi/iqn.../portals/> create ::
Which should create a portal [::]:3260
Initiate SendTargets discovery to the portal using an IPv4 address
# iscsiadm -m discovery -t st -p 127.0.0.1
The response formats TargetAddress as [::ffff:127.0.0.1]:3260,1
This still works and uses v4 on the network between two v6 sockets, but
only if the initiator supports IPv6 with v4-mapped addresses.
This change detects v4-mapped address on v6 sockets for the wildcard
case, and instead formats the TargetAddress response as an IPv4 address.
In order to not further complicate iscsit_build_sendtargets_response,
I've actually simplified it by moving the bracket wrapping of IPv6
address into iscsit_accept_np where local_ip and login_ip strings are
set. That also simplifies iscsi_stat_tgt_attr_show_attr_fail_intr_addr.
Side effect of the string format change is that
lio_target_nacl_show_info will now print login_ip bracket wrapped for
IPv6 connections, as will a few debug prints.
Signed-off-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The usage of strict_strtoul() and strict_strtoull() is not preferred,
because strict_strtoul() and strict_strtoull() are obsolete. Thus,
kstrtoul() and kstrtoull() should be used.
v2: Fix incorrect return in ft_add_tpg (Fengguang)
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes spc_emulate_inquiry_std() to add trailing ASCII
spaces for INQUIRY vendor + model fields following SPC-4 text:
"ASCII data fields described as being left-aligned shall have any
unused bytes at the end of the field (i.e., highest offset) and
the unused bytes shall be filled with ASCII space characters (20h)."
This addresses a problem with Falconstor NSS multipathing.
Reported-by: Tomas Molota <tomas.molota@lightstorm.sk>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull SCSI target updates from Nicholas Bellinger:
"Lots of activity this round on performance improvements in target-core
while benchmarking the prototype scsi-mq initiator code with
vhost-scsi fabric ports, along with a number of iscsi/iser-target
improvements and hardening fixes for exception path cases post v3.10
merge.
The highlights include:
- Make persistent reservations APTPL buffer allocated on-demand, and
drop per t10_reservation buffer. (grover)
- Make virtual LUN=0 a NULLIO device, and skip allocation of NULLIO
device pages (grover)
- Add transport_cmd_check_stop write_pending bit to avoid extra
access of ->t_state_lock is WRITE I/O submission fast-path. (nab)
- Drop unnecessary CMD_T_DEV_ACTIVE check from
transport_lun_remove_cmd to avoid extra access of ->t_state_lock in
release fast-path. (nab)
- Avoid extra t_state_lock access in __target_execute_cmd fast-path
(nab)
- Drop unnecessary vhost-scsi wait_for_tasks=true usage +
->t_state_lock access in release fast-path. (nab)
- Convert vhost-scsi to use modern se_cmd->cmd_kref
TARGET_SCF_ACK_KREF usage (nab)
- Add tracepoints for SCSI commands being processed (roland)
- Refactoring of iscsi-target handling of ISCSI_OP_NOOP +
ISCSI_OP_TEXT to be transport independent (nab)
- Add iscsi-target SendTargets=$IQN support for in-band discovery
(nab)
- Add iser-target support for in-band discovery (nab + Or)
- Add iscsi-target demo-mode TPG authentication context support (nab)
- Fix isert_put_reject payload buffer post (nab)
- Fix iscsit_add_reject* usage for iser (nab)
- Fix iscsit_sequence_cmd reject handling for iser (nab)
- Fix ISCSI_OP_SCSI_TMFUNC handling for iser (nab)
- Fix session reset bug with RDMA_CM_EVENT_DISCONNECTED (nab)
The last five iscsi/iser-target items are CC'ed to stable, as they do
address issues present in v3.10 code. They are certainly larger than
I'd like for stable patch set, but are important to ensure proper
REJECT exception handling in iser-target for 3.10.y"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (51 commits)
iser-target: Ignore non TEXT + LOGOUT opcodes for discovery
target: make queue_tm_rsp() return void
target: remove unused codes from enum tcm_tmrsp_table
iscsi-target: kstrtou* configfs attribute parameter cleanups
iscsi-target: Fix tfc_tpg_auth_cit configfs length overflow
iscsi-target: Fix tfc_tpg_nacl_auth_cit configfs length overflow
iser-target: Add support for ISCSI_OP_TEXT opcode + payload handling
iser-target: Rename sense_buf_[dma,len] to pdu_[dma,len]
iser-target: Add vendor_err debug output
target: Add (obsolete) checking for PMI/LBA fields in READ CAPACITY(10)
target: Return correct sense data for IO past the end of a device
target: Add tracepoints for SCSI commands being processed
iser-target: Fix session reset bug with RDMA_CM_EVENT_DISCONNECTED
iscsi-target: Fix ISCSI_OP_SCSI_TMFUNC handling for iser
iscsi-target: Fix iscsit_sequence_cmd reject handling for iser
iscsi-target: Fix iscsit_add_reject* usage for iser
iser-target: Fix isert_put_reject payload buffer post
iscsi-target: missing kfree() on error path
iscsi-target: Drop left-over iscsi_conn->bad_hdr
target: Make core_scsi3_update_and_write_aptpl return sense_reason_t
...
The return value wasn't checked by any of the callers. Assuming this is
correct behaviour, we can simplify some code by not bothering to
generate it.
nab: Add srpt_queue_data_in() + srpt_queue_tm_rsp() nops around
srpt_queue_response() void return
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Three have been checked for but were never set. Remove the dead code.
Also renumbers the remaining ones to a) get rid of the holes after the
removal and b) avoid a collision between TMR_FUNCTION_COMPLETE==0 and
the uninitialized case. If we failed to set a code, we should rather
fall into the default case then return success.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch includes the conversion of iscsi-target configfs
attributes for NetworkPortal, NodeACL, TPG, IQN and Discovery
groups to use kstrtou*() instead of simple_strtou*().
It also cleans up new-line usage during iscsi_tpg_param_store_##name
to use isspace().
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes another potential buffer overflow while processing
iscsi_node_auth input for configfs attributes in v3.11 for-next
TPG tfc_tpg_auth_cit context.
Reported-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a potential buffer overflow while processing
iscsi_node_auth input for configfs attributes within NodeACL
tfc_tpg_nacl_auth_cit context.
Signed-off-by: Joern Engel <joern@logfs.org>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The SBC-2 specification of READ CAPACITY(10) has PMI and LOGICAL BLOCK
ADDRESS fields in the CDB; in SBC-3 these fields are simply listed as
obsolete. However, SBC-2 also has the language
If the PMI bit is set to zero and the LOGICAL BLOCK ADDRESS field
is not set to zero, the device server shall terminate the command
with CHECK CONDITION status with the sense key set to ILLEGAL
REQUEST and the additional sense code set to INVALID FIELD IN CDB.
and in fact at least the Windows SCSI compliance test checks this
behavior. Since no one following SBC-3 is going to set these fields,
we might as well include the check from SBC-2 and pass this test.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We should use TCM_ADDRESS_OUT_OF_RANGE (-> sense data LOGICAL BLOCK
ADDRESS OUT OF RANGE) for IOs past the end of a device instead of
INVALID FIELD IN CDB.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds tracepoints to the target code for commands being
received and being completed, which is quite useful for debugging
interactions with initiators. For example, one can do something like the
following to watch commands that are completing unsuccessfully:
# echo 'scsi_status!=0' > /sys/kernel/debug/tracing/events/target/target_cmd_complete/filter
# echo 1 > /sys/kernel/debug/tracing/events/target/target_cmd_complete/enable
<run command that fails>
# cat /sys/kernel/debug/tracing/trace
iscsi_trx-0-1902 [003] ...1 990185.810385: target_cmd_complete: iqn.1993-08.org.debian:01:e51ede6aacfd <- LUN 001 status CHECK CONDITION (sense len 18 / 70 00 05 00 00 00 00 0a 00 00 00 00 20 00 00 00 00 00) 0x95 data_length 512 CDB 95 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 (TA:SIMPLE C:00)
(v2: Drop undefined COMPARE_AND_WRITE)
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses a bug where RDMA_CM_EVENT_DISCONNECTED may occur
before the connection shutdown has been completed by rx/tx threads,
that causes isert_free_conn() to wait indefinately on ->conn_wait.
This patch allows isert_disconnect_work code to invoke rdma_disconnect
when isert_disconnect_work() process context is started by client
session reset before isert_free_conn() code has been reached.
It also adds isert_conn->conn_mutex protection for ->state within
isert_disconnect_work(), isert_cq_comp_err() and isert_free_conn()
code, along with isert_check_state() for wait_event usage.
(v2: Add explicit iscsit_cause_connection_reinstatement call
during isert_disconnect_work() to force conn reset)
Cc: stable@vger.kernel.org # 3.10+
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds target_get_sess_cmd reference counting for
iscsit_handle_task_mgt_cmd(), and adds a target_put_sess_cmd()
for the failure case.
It also fixes a bug where ISCSI_OP_SCSI_TMFUNC type commands
where leaking iscsi_cmd->i_conn_node and eventually triggering
an OOPs during struct isert_conn shutdown.
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch moves ISCSI_OP_REJECT failures into iscsit_sequence_cmd()
in order to avoid external iscsit_reject_cmd() reject usage for all
PDU types.
It also updates PDU specific handlers for traditional iscsi-target
code to not reset the session after posting a ISCSI_OP_REJECT during
setup.
(v2: Fix CMDSN_LOWER_THAN_EXP for ISCSI_OP_SCSI to call
target_put_sess_cmd() after iscsit_sequence_cmd() failure)
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes iscsit_add_reject() + iscsit_add_reject_from_cmd()
usage to not sleep on iscsi_cmd->reject_comp to address a free-after-use
usage bug in v3.10 with iser-target code.
It saves ->reject_reason for use within iscsit_build_reject() so the
correct value for both transport cases. It also drops the legacy
fail_conn parameter usage throughput iscsi-target code and adds
two iscsit_add_reject_cmd() and iscsit_reject_cmd helper functions,
along with various small cleanups.
(v2: Re-enable target_put_sess_cmd() to be called from
iscsit_add_reject_from_cmd() for rejects invoked after
target_get_sess_cmd() has been called)
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Fix-up breakage in iscsit_build_sendtargets_response() from v3.11
changes, and free "payload" before returning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
All REJECT response setup of the rejected payload is now done using
on-demand cmd->buf_ptr allocations.
Go ahead and remove dead iscsi_conn->bad_hdr usage rx_opcode path
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Fix up sense_reason_t breakage in core_scsi3_update_and_write_aptpl()
from recent conversion to use local scope memory allocation.
Reported as sparse warnings: (new ones prefixed by >>) by Fengguang:
>> drivers/target/target_core_pr.c:2069:57: sparse: incorrect type in
>> return expression (different base types)
drivers/target/target_core_pr.c:2069:57: expected restricted sense_reason_t
drivers/target/target_core_pr.c:2069:57: got int
>> drivers/target/target_core_pr.c:2179:21: sparse: incorrect type in
>> assignment (different base types)
drivers/target/target_core_pr.c:2179:21: expected restricted sense_reason_t [assigned] [usertype] ret
drivers/target/target_core_pr.c:2179:21: got int
>> drivers/target/target_core_pr.c:2197:13: sparse: incorrect type in
>> assignment (different base types)
drivers/target/target_core_pr.c:2197:13: expected restricted sense_reason_t [assigned] [usertype] ret
drivers/target/target_core_pr.c:2197:13: got int
drivers/target/target_core_pr.c:1245:28: sparse: context imbalance in '__core_scsi3_free_registration' - unexpected unlock
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a auth configfs group context following existing
explict NodeACL and discovery auth within:
/sys/kernel/config/target/iscsi/$TARGETNAME/$TPGT/auth/
This patch allows these attributes to be used for CHAP authentication
an TPG is configured in demo-mode (generate_node_acl=1).
Note this authentication information takes precedence over NodeACL
authentication when struct se_node_acl->dynamic_node_acl is present.
Cc: Dax Kelson <dkelson@gurulabs.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds an optional /auth/ configfs group to TPG context that
can be used by fabrics like iscsi-target for TPG demo-mode
authentication.
Cc: Dax Kelson <dkelson@gurulabs.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes ISCSI_OP_TEXT handling of SendTargets=[iqn.,eui.]
payloads to return explicit discovery information.
It adds checks to iscsit_process_text_cmd() and adds the special single
$TARGETNAME discovery case in iscsit_build_sendtargets_response() code.
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch moves ISCSI_OP_TEXT PDU buffer sanity checks to
iscsit_process_text_cmd() code, so that it can be shared
with iser-target code.
It adds IFC_SENDTARGETS_ALL + iscsi_cmd->text_in_ptr in order
to save text payload for ISCSI_OP_TEXT_RSP, and updates
iscsit_release_cmd() to assigned memory.
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes iscsi_set_connection_parameters() to allow
conn_ops->MaxXmitDataSegmentLength assignement to occur during
in-band iser send-targets discovery, as this value is required
by TEXT response processing code.
Reported-by: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch refactoring existing iscsit_send_text_rsp() in order
to handle iscsi_text_rsp payloads in a transport specific manner.
This includes the addition of iscsit_build_text_rsp() to build
the response payload and initialize ISCSI_OP_TEXT_RSP.
v2: Make iscsit_build_text_rsp() determine extra padding bytes, and
drop legacy padding calculation for traditional iSCSI text
responses within iscsit_send_text_rsp()
Reported-by: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch refactors ISCSI_OP_TEXT handling within iscsi-target in
order to handle iscsi_text payloads in a transport specific manner.
This includes splitting current iscsit_handle_text_cmd() into
iscsit_setup_text_cmd() and iscsit_process_text_cmd() calls, and
makes iscsit_handle_text_cmd be only used internally by traditional
iscsi socket calls.
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch refactors ISCSI_OP_NOOP handling within iscsi-target in
order to handle iscsi_nopout payloads in a transport specific manner.
This includes splitting existing iscsit_handle_nop_out() into
iscsit_setup_nop_out() and iscsit_process_nop_out() calls, and
makes iscsit_handle_nop_out() be only used internally by traditional
iscsi socket calls.
Next update iser-target code to use new callers and add FIXME for
the handling iscsi_nopout payloads. Also fix reject response handling
in iscsit_setup_nop_out() to use proper iscsit_add_reject_from_cmd().
v2: Fix uninitialized iscsit_handle_nop_out() payload_length usage (Fengguang)
v3: Remove left-over dead code in iscsit_setup_nop_out() (DanC)
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Writing 0 when iser was not previously enabled, so succeed but do
nothing so that user-space code doesn't need a try: catch block
when ib_isert logic is not available.
Also, return actual error from add_network_portal using PTR_ERR
during op=enable failure.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now with iscsi-target using modern se_cmd->cmd_kref accounting in
v3.10 code, it's safe to go ahead and drop the legacy release
codepath + se_cmd->check_release bit in transport_release_cmd()
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@kernel.org>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Moussa Ba <moussaba@micron.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In modern iscsi-target code, the setup and I/O submission is done within a
single process context, so there is no need to acquire se_cmd->t_state_lock while
checking SCF_SUPPORTED_SAM_OPCODE for determining when unsolicited data-out
should be dumped.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@kernel.org>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Moussa Ba <moussaba@micron.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch drops the se_cmd->t_state_lock access around SCF_SUPPORTED_SAM_OPCODE
assignment within target_setup_cmd_from_cdb().
Original v4.0 target code required this as fabrics would be checking for
this values in different process contexts for setup and I/O submission.
Given that modern v4.1 target code performs setup and I/O submission
from the same process context, this t_state_lock access is no longer
required.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@kernel.org>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Moussa Ba <moussaba@micron.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch makes target_execute_cmd() set CMD_T_BUSY|CMD_T_SENT while
holding se_cmd->t_state_lock, in order to avoid the extra aquire/release
in __target_execute_cmd().
It also clears these bits in case of a target_handle_task_attr()
failure.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@kernel.org>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Moussa Ba <moussaba@micron.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch removes legacy se_cmd->t_fe_count usage in order to avoid
se_cmd->t_state_lock access within transport_put_cmd() during normal
fast path se_cmd descriptor release.
Also drop the left-over parameter usage within core_tmr_handle_tas_abort()
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@kernel.org>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Moussa Ba <moussaba@micron.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch drops an unnecessary acquire/release of se_cmd->t_state_lock within
transport_lun_remove_cmd() when checking CMD_T_DEV_ACTIVE for invoking
target_remove_from_state_list().
For all fast path completion cases, transport_lun_remove_cmd() is always
called ahead of transport_cmd_check_stop(), and since transport_cmd_check_stop()
is calling target_remove_from_state_list() when remove_from_lists=true,
the t_state_lock usage in transport_lun_remove_cmd() can safely be removed.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@kernel.org>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Moussa Ba <moussaba@micron.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a new transport_cmd_check_stop() parameter for signaling
when TRANSPORT_WRITE_PENDING needs to be set.
This allows transport_generic_new_cmd() to avoid the extra lock acquire/release
of ->t_state_lock in the fast path for DMA_TO_DEVICE operations ahead of
transport_cmd_check_stop() + se_tfo->write_pending().
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@kernel.org>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Moussa Ba <moussaba@micron.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Here is a fun one. Bug seems to have been introduced by commit 140854cb,
almost two years ago. I have no idea why we only started seeing it now,
but we did.
Rough callgraph:
core_tpg_set_initiator_node_queue_depth()
`-> spin_lock_irqsave(&tpg->session_lock, flags);
`-> lio_tpg_shutdown_session()
`-> iscsit_stop_time2retain_timer()
`-> spin_unlock_bh(&se_tpg->session_lock);
`-> spin_lock_bh(&se_tpg->session_lock);
`-> spin_unlock_irqrestore(&tpg->session_lock, flags);
core_tpg_set_initiator_node_queue_depth() used to call spin_lock_bh(),
but 140854cb changed that to spin_lock_irqsave(). However,
lio_tpg_shutdown_session() still claims to be called with spin_lock_bh()
held, as does iscsit_stop_time2retain_timer():
* Called with spin_lock_bh(&struct se_portal_group->session_lock) held
Stale documentation is mostly annoying, but in this case the dropping
the lock with the _bh variant is plain wrong. It is also wrong to drop
locks two functions below the lock-holder, but I will ignore that bit
for now.
After some more locking and unlocking we eventually hit this backtrace:
------------[ cut here ]------------
WARNING: at kernel/softirq.c:159 local_bh_enable_ip+0xe8/0x100()
Pid: 24645, comm: lio_helper.py Tainted: G O 3.6.11+
Call Trace:
[<ffffffff8103e5ff>] warn_slowpath_common+0x7f/0xc0
[<ffffffffa040ae37>] ? iscsit_inc_conn_usage_count+0x37/0x50 [iscsi_target_mod]
[<ffffffff8103e65a>] warn_slowpath_null+0x1a/0x20
[<ffffffff810472f8>] local_bh_enable_ip+0xe8/0x100
[<ffffffff815b8365>] _raw_spin_unlock_bh+0x15/0x20
[<ffffffffa040ae37>] iscsit_inc_conn_usage_count+0x37/0x50 [iscsi_target_mod]
[<ffffffffa041149a>] iscsit_stop_session+0xfa/0x1c0 [iscsi_target_mod]
[<ffffffffa0417fab>] lio_tpg_shutdown_session+0x7b/0x90 [iscsi_target_mod]
[<ffffffffa033ede4>] core_tpg_set_initiator_node_queue_depth+0xe4/0x290 [target_core_mod]
[<ffffffffa0409032>] iscsit_tpg_set_initiator_node_queue_depth+0x12/0x20 [iscsi_target_mod]
[<ffffffffa0415c29>] lio_target_nacl_store_cmdsn_depth+0xa9/0x180 [iscsi_target_mod]
[<ffffffffa0331b49>] target_fabric_nacl_base_attr_store+0x39/0x40 [target_core_mod]
[<ffffffff811b857d>] configfs_write_file+0xbd/0x120
[<ffffffff81148f36>] vfs_write+0xc6/0x180
[<ffffffff81149251>] sys_write+0x51/0x90
[<ffffffff815c0969>] system_call_fastpath+0x16/0x1b
---[ end trace 3747632b9b164652 ]---
As a pure band-aid, this patch drops the _bh.
Signed-off-by: Joern Engel <joern@logfs.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Nobody should be expecting to read or write virtual_lun0.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Use bool params when appropriate.
Eliminate unneeded pr_reg_e and type variables.
Just one goto label, so rename to 'out' from 'out_put_pr_reg'.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Don't need goto, we can just do an if/else for sa_res_key behavior. Move
shorter case first. Slightly shorter b/c both cases can share a call to
update_and_write_aptpl() now.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Instead of taking the buffer and length, update_and_write_aptpl() will
allocate the buffer as needed, and then free it. Instead, the function
takes an 'aptpl' boolean parameter.
This enables us to remove memory alloc/frees from struct
t10_pr_registration and other spots.
There is a slight loss of functionality because each callsite doesn't get
its own pr_debug any more, but this info can be cleaned via ftrace if
necessary and I think the shorter code is worth it.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
As mentioned in the comments in update_and_write_aptpl,
write_aptpl_to_file() calls strlen() on the buffer, and the length was
always being passed as zero.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
It's only ever set to PR_APTPL_BUF_LEN, so we don't need a variable.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The __ version is only ever called from the regular version, so just
inline it. It's not too much more complex to handle both spinlocks in the
same function.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Simpler to just set buf in update_and_write_aptpl(), rather than passing
down to ____core_scsi3_update_aptpl_buf().
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
They're in emulate_pro_register, so change UNREGISTER to REGISTER.
The first one seems wrong -- sa_res_key could be 0 there, but it's testing
spec_i_pt.
Remove unneeded parens in 2nd conditional.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We use this function exclusively in debug prints. Instead of returning
0 or 1 if isid is present, just set buf to "" if it isn't there. This
saves callers from having to check the return value.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
core_scsi3_enulate_pro_register took an 'ignore_key' parameter that
really distinguished between REGISTER and REGISTER_AND_IGNORE_EXISTING_KEY
registration types, which was a little confusing. Same situation for
PREEMPT and PREEMPT_AND_ABORT. Use enums to add a little more
descriptiveness to the code.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Go ahead and propigate up the ->cmd_kref put return value from
target_put_sess_cmd() -> transport_release_cmd() -> transport_put_cmd()
-> transport_generic_free_cmd().
This is useful for certain fabrics when determining the active I/O
shutdown case with SCF_ACK_KREF where a final target_put_sess_cmd()
is still required by the caller.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
If a key was larger than 64 bytes, as checked by iscsi_check_key(), the
error response packet, generated by iscsi_add_notunderstood_response(),
would still attempt to copy the entire key into the packet, overflowing
the structure on the heap.
Remote preauthentication kernel memory corruption was possible if a
target was configured and listening on the network.
CVE-2013-2850
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a bug where FILEIO was incorrectly reporting the number
of logical blocks (+ 1) when using non struct block_device export mode.
It changes fd_get_blocks() to follow all other backend ->get_blocks() cases,
and reduces the calculated dev_size by one dev->dev_attrib.block_size
number of bytes, and also fixes initial fd_block_size assignment at
fd_configure_device() time introduced in commit 0fd97ccf4.
Reported-by: Wenchao Xia <xiawenc@linux.vnet.ibm.com>
Reported-by: Badari Pulavarty <pbadari@us.ibm.com>
Tested-by: Badari Pulavarty <pbadari@us.ibm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Switch back to pre commit 1c7b13fe65 list splicing logic for active I/O
shutdown with tcm_qla2xxx + ib_srpt fabrics.
The original commit was done under the incorrect assumption that it's safe to
walk se_sess->sess_cmd_list unprotected in target_wait_for_sess_cmds() after
sess->sess_tearing_down = 1 has been set by target_sess_cmd_list_set_waiting()
during session shutdown.
So instead of adding sess->sess_cmd_lock protection around sess->sess_cmd_list
during target_wait_for_sess_cmds(), switch back to sess->sess_wait_list to
allow wait_for_completion() + TFO->release_cmd() to occur without having to
walk ->sess_cmd_list after the list_splice.
Also add a check to exit if target_sess_cmd_list_set_waiting() has already
been called, and add a WARN_ON to check for any fabric bug where new se_cmds
are added to sess->sess_cmd_list after sess->sess_tearing_down = 1 has already
been set.
Cc: Joern Engel <joern@logfs.org>
Cc: Roland Dreier <roland@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Drop unused transport_wait_for_tasks() check in target_wait_for_sess_cmds
shutdown code, and convert tcm_qla2xxx + ib_srpt fabric drivers.
Cc: Joern Engel <joern@logfs.org>
Cc: Roland Dreier <roland@kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull target fixes from Nicholas Bellinger:
"A handful of fixes + minor changes this time around, along with one
important >= v3.9 regression fix for IBLOCK backends. The highlights
include:
- Use FD_MAX_SECTORS in FILEIO for block_device as
well as files (agrover)
- Fix processing of out-of-order CmdSNs with
iSBD driver (shlomo)
- Close long-standing target_put_sess_cmd() vs.
core_tmr_abort_task() race with the addition of
kref_put_spinlock_irqsave() (joern + greg-kh)
- Fix IBLOCK WCE=1 + DPOFUA=1 backend WRITE
regression in >= v3.9 (nab + bootc)
Note these four patches are CC'ed to stable.
Also, there is still some work left to be done on the active I/O
shutdown path in target_wait_for_sess_cmds() used by tcm_qla2xxx +
ib_isert fabrics that is still being discussed on the list, and will
hopefully be resolved soon."
* 'queue' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: close target_put_sess_cmd() vs. core_tmr_abort_task() race
target: removed unused transport_state flag
target/iblock: Fix WCE=1 + DPOFUA=1 backend WRITE regression
MAINTAINERS: Update target git tree URL
iscsi-target: Fix typos in RDMAEXTENSIONS macro usage
target/rd: Add ramdisk bit for NULLIO operation
iscsi-target: Fix processing of OOO commands
iscsi-target: Make buf param of iscsit_do_crypto_hash_buf() const void *
iscsi-target: Fix NULL pointer dereference in iscsit_send_reject
target: Have dev/enable show if TCM device is configured
target: Use FD_MAX_SECTORS/FD_BLOCKSIZE for blockdevs using fileio
target: Remove unused struct members in se_dev_entry
It is possible for one thread to to take se_sess->sess_cmd_lock in
core_tmr_abort_task() before taking a reference count on
se_cmd->cmd_kref, while another thread in target_put_sess_cmd() drops
se_cmd->cmd_kref before taking se_sess->sess_cmd_lock.
This introduces kref_put_spinlock_irqsave() and uses it in
target_put_sess_cmd() to close the race window.
Signed-off-by: Joern Engel <joern@logfs.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a regression bug introduced in v3.9-rc1 where if the
underlying struct block_device for a IBLOCK backend is configured with
WCE=1 + DPOFUA=1 settings, the rw = WRITE assignment no longer occurs
in iblock_execute_rw(), and rw = 0 is passed to iblock_submit_bios()
in effect causing a READ bio operation to occur.
The offending commit is:
commit d0c8b259f8
Author: Nicholas Bellinger <nab@linux-iscsi.org>
Date: Tue Jan 29 22:10:06 2013 -0800
target/iblock: Use backend REQ_FLUSH hint for WriteCacheEnabled status
Note the WCE=1 + DPOFUA=0, WCE=0 + DPOFUA=1, and WCE=0 + DPOFUA=0 cases
are not affected by this regression bug.
Reported-by: Chris Boot <bootc@bootc.net>
Tested-by: Chris Boot <bootc@bootc.net>
Reported-by: Hannes Reinecke <hare@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a rd_nullio parameter that allows RAMDISK_MCP backends
to function in NULLIO mode, where all se_cmd I/O is immediately completed
in rd_execute_rw() without actually performing the SGL memory copy.
This is useful for performance testing when the ramdisk SGL memory copy
begins to eat lots of cycles during heavy small block workloads, so allow
this bit to be enabled when necessary on a per rd_dev basis.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Fix two issues in OOO commands processing done at iscsit_attach_ooo_cmdsn.
Handle command serial numbers wrap around by using iscsi_sna_lt and not regular comparisson.
The routine iterates until it finds an entry whose serial number is greater than the serial number of
the new one, thus the new entry should be inserted before that entry and not after.
Signed-off-by: Shlomo Pongratz <shlomop@mellanox.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Make the "buf" input param of iscsit_do_crypto_hash_buf() "const void *".
This allows to remove lots of casts in its callers.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Fix up a NULL pointer dereference regression in iscsit_send_reject()
introduced by from commit 2ec5a8c11.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
User tools need to know if the device is properly configured, since if
not, some other attributes are invalid.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We can still see the error reported in
https://patchwork.kernel.org/patch/2338981/
when using fileio backed by a block device.
I'm assuming this will get us past that error (from sbc_parse_cdb),
and also assuming it's OK to have our max_sectors be larger than
the block's queue max hw sectors?
Reported-by: Eric Harney <eharney@redhat.com>
Signed-off-by: Andy Grover <agrover@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Some were incremented, but never used anywhere from what I could tell.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull VFS updates from Al Viro,
Misc cleanups all over the place, mainly wrt /proc interfaces (switch
create_proc_entry to proc_create(), get rid of the deprecated
create_proc_read_entry() in favor of using proc_create_data() and
seq_file etc).
7kloc removed.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (204 commits)
don't bother with deferred freeing of fdtables
proc: Move non-public stuff from linux/proc_fs.h to fs/proc/internal.h
proc: Make the PROC_I() and PDE() macros internal to procfs
proc: Supply a function to remove a proc entry by PDE
take cgroup_open() and cpuset_open() to fs/proc/base.c
ppc: Clean up scanlog
ppc: Clean up rtas_flash driver somewhat
hostap: proc: Use remove_proc_subtree()
drm: proc: Use remove_proc_subtree()
drm: proc: Use minor->index to label things, not PDE->name
drm: Constify drm_proc_list[]
zoran: Don't print proc_dir_entry data in debug
reiserfs: Don't access the proc_dir_entry in r_open(), r_start() r_show()
proc: Supply an accessor for getting the data from a PDE's parent
airo: Use remove_proc_subtree()
rtl8192u: Don't need to save device proc dir PDE
rtl8187se: Use a dir under /proc/net/r8180/
proc: Add proc_mkdir_data()
proc: Move some bits from linux/proc_fs.h to linux/{of.h,signal.h,tty.h}
proc: Move PDE_NET() to fs/proc/proc_net.c
...
Add a check for an aborted sequence, which has a
NULL sequence pointer, to avoid target crashes.
The most relevant messages from the crash (entered
from video capture) include:
BUG: unable to handle kernel paging request at ffffffffffffffdf
IP: [<ffffffffa02d514c>] fc_seq_send+0x3c/0x150 [libfc]
...
Call Trace:
[<ffffffffa0443de6>] ft_queue_data_in+0x266/0x560 [tcm_fc]
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a new network portal attribute for iser, that lives
under existing iscsi-target configfs layout at:
/sys/kernel/config/target/iscsi/$TARGETNAME/$TPGT/np/$PORTAL/iser
When lio_target_np_store_iser() is enabled, iscsit_tpg_add_network_portal()
will attempt to start an rdma_cma network portal for iser-target, only if
the external ib_isert module transport has been loaded.
When disabled, iscsit_tpg_del_network_portal() will cease iser login service
on the network portal, and release any external ib_isert module reference.
v4 changes:
- Add request_module for ib_isert to lio_target_np_store_iser()
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch refactors TX immediate + response queue handling to use
the new iscsit_transport API callers, and exports the necessary
traditional iscsi PDU response creation functions for iser-target
to utilize.
This includes:
- Add iscsit_build_datain_pdu() for DATAIN PDU init + convert
iscsit_build_datain_pdu()
- Add iscsit_build_logout_rsp() for LOGOUT_RSP PDU init + convert
iscsit_send_logout()
- Add iscsit_build_nopin_rsp() for NOPIN_RSP PDU init + convert
iscsit_send_nopin()
- Add iscsit_build_rsp_pdu() for SCSI_RSP PDU init + convert
iscsit_send_response()
- Add iscsit_build_task_mgt_rsp for TM_RSP PDU init + convert
iscsit_send_task_mgt_rsp()
- Refactor immediate queue state switch into iscsit_immediate_queue()
- Convert handle_immediate_queue() to use iscsit_transport caller
- Refactor response queue state switch into iscsit_response_queue()
- Convert handle_response_queue to use iscsit_transport caller
- Export iscsit_logout_post_handler(), iscsit_increment_maxcmdsn()
and iscsit_tmr_post_handler() for external transport module usage
v5 changes:
- Fix solicited NopIN handling with RDMAExtensions=No (nab)
v3 changes:
- Add iscsit_build_reject for REJECT PDU init + convert
iscsit_send_reject()
v2 changes:
- Add iscsit_queue_rsp() for iscsit_transport->iscsit_queue_data_in()
and iscsit_transport->iscsit_queue_status()
- Update lio_queue_data_in() to use ->iscsit_queue_data_in()
- Update lio_queue_status() to use ->iscsit_queue_status()
- Use mutex_trylock() in iscsit_increment_maxcmdsn()
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch refactors existing traditional iscsi RX side PDU handling
to use iscsit_transport, and exports the necessary logic for external
transport modules.
This includes:
- Refactor iscsit_handle_scsi_cmd() into PDU setup / processing
- Add updated iscsit_handle_scsi_cmd() for tradtional iscsi code
- Add iscsit_set_unsoliticed_dataout() wrapper
- Refactor iscsit_handle_data_out() into PDU check / processing
- Add updated iscsit_handle_data_out() for tradtional iscsi code
- Add iscsit_handle_nop_out() + iscsit_handle_task_mgt_cmd() to
accept pre-allocated struct iscsi_cmd
- Add iscsit_build_r2ts_for_cmd() caller for iscsi_target_transport
to handle ISTATE_SEND_R2T for TX immediate queue
- Refactor main traditional iscsi iscsi_target_rx_thread() PDU switch
into iscsi_target_rx_opcode() using iscsit_allocate_cmd()
- Turn iscsi_target_rx_thread() process context into NOP for
ib_isert side work-queue.
v5 changes:
- Make iscsit_handle_scsi_cmd() static (Fengguang)
- Fix iscsit_handle_scsi_cmd() exception se_cmd leak (nab)
v3 changes:
- Add extra target_put_sess_cmd call in iscsit_add_reject_from_cmd
after completion
v2 changes:
- Disable iscsit_ack_from_expstatsn() usage for RDMAExtentions=Yes
- Disable iscsit_allocate_datain_req() usage for RDMAExtentions=Yes
- Add target_get_sess_cmd() reference counting to
iscsit_setup_scsi_cmd()
- Add TFO->lio_check_stop_free() fabric API caller
- Add export of iscsit_stop_dataout_timer() symbol
- Add iscsit_build_r2ts_for_cmd() for iscsit_transport->iscsit_get_dataout()
- Convert existing usage of iscsit_build_r2ts_for_cmd() to
->iscsit_get_dataout()
- Drop RDMAExtentions=Yes specific check in iscsit_build_r2ts_for_cmd()
- Fix RDMAExtentions -> RDMAExtensions typo (andy)
- Pass correct dump_payload value into iscsit_get_immediate_data()
for iscsit_handle_scsi_cmd()
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts struct iscsi_cmd memory allocation + free to use
->iscsit_alloc_cmd() iscsit_transport API caller, and export
iscsit_allocate_cmd() symbols
Also add iscsi_cmd->release_cmd() to be used seperately from
iscsit_transport for connection/session shutdown.
v2 changes:
- Remove unnecessary checks in iscsit_alloc_cmd (asias)
- Drop iscsit_transport->iscsit_free_cmd() usage
- Drop iscsit_transport->iscsit_unmap_cmd() usage
- Add iscsi_cmd->release_cmd()
- Convert lio_release_cmd() to use iscsi_cmd->release_cmd()
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds RDMAExtensions, InitiatorRecvDataSegmentLength and
TargetRecvDataSegmentLength parameters keys necessary for iser-target
login to occur.
This includes setting the necessary parameters during login path
code within iscsi_login_zero_tsih_s2(), and currently PAGE_SIZE
aligning the target's advertised MRDSL for immediate data and
unsolicited data-out incoming payloads.
v3 changes:
- Add iscsi_post_login_start_timers FIXME for ISER
v2 changes:
- Fix RDMAExtentions -> RDMAExtensions typo (andy)
- Drop unnecessary '== true' conditional checks for type bool
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch performs the initial conversion of existing traditional iscsi
to use iscsit_transport API callers. This includes:
- iscsi-np cleanups for iscsit_transport_type
- Add iscsi-np transport calls w/ ->iscsit_setup_up() and ->iscsit_free_np()
- Convert login thread process context to use ->iscsit_accept_np() for
connections with pre-allocated struct iscsi_conn
- Convert existing socket accept code to iscsit_accept_np()
- Convert login RX/TX callers to use ->iscsit_get_login_rx() and
->iscsit_put_login_tx() to exchange request/response PDUs
- Convert existing socket login RX/TX calls into iscsit_get_login_rx()
and iscsit_put_login_tx()
- Change iscsit_close_connection() to invoke ->iscsit_free_conn() +
iscsit_put_transport() calls.
- Add iscsit_register_transport() + iscsit_unregister_transport() calls
to module init/exit
v4 changes:
- Add missing iscsit_put_transport() call in iscsi_target_setup_login_socket()
failure case
v2 changes:
- Update module init/exit to use register_transport() + unregister_transport()
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Add basic struct iscsit_transport API template to allow iscsi-target for
running with external transport modules using existing iscsi_target_core.h
code.
For all external modules, this calls try_module_get() and module_put()
to obtain + release an external iscsit_transport module reference count.
Also include the iscsi-target symbols necessary in iscsi_transport.h to
allow external transport modules to function.
v3 changes:
- Add iscsit_build_reject export for ISTATE_SEND_REJECT usage
v2 changes:
- Drop unnecessary export of iscsit_get_transport + iscsit_put_transport (roland)
- Add ->iscsit_queue_data_in() to remove extra context switch on RDMA_WRITE
- Add ->iscsit_queue_status() to remove extra context switch on IB_SEND status
- Add ->iscsit_get_dataout() to remove extra context switch on RDMA_READ
- Drop ->iscsit_free_cmd()
- Drop ->iscsit_unmap_cmd()
- Rename iscsit_create_transport() -> iscsit_register_transport() (andy)
- Rename iscsit_destroy_transport() -> iscsit_unregister_transport() (andy)
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
As the comment sais, this allows Solaris initiators to survive
intermittent errors. The comment from someone reading the Solaris
sources seem to imply that multipathing would be broken without this
patch as well.
Signed-off-by: Joern Engel <joern@logfs.org>
Cc: Brian Bunker <brian@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Set is_nonrot attribute according to the block queue if the backend
device is a block device.
Signed-off-by: Asias He <asias@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
iblock_execute_unmap() and fd_execute_unmap share a lot of code.
Add sbc_execute_unmap() helper to remove duplicated code for
iblock_execute_unmap() and fd_execute_unmap().
Cc: Christoph Hellwig <hch@lst.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Asias He <asias@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Add helper iblock_do_unmap() to remove duplicated code in
iblock_execute_write_same_unmap() and iblock_execute_unmap().
Cc: Christoph Hellwig <hch@lst.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Asias He <asias@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Add helper fd_do_unmap() to remove duplicated code in
fd_execute_write_same_unmap() and fd_execute_unmap().
Cc: Christoph Hellwig <hch@lst.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Asias He <asias@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds support for emulation of UNMAP within
fd_execute_unmap() backend code.
If the FILEIO backend is normal file, the emulation uses fallocate to
punch hole to reclaim the free space used by the file. If the FILEIO
backend is block device, the emulation uses blkdev_issue_discard().
Cc: Christoph Hellwig <hch@lst.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Asias He <asias@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds support for emulation of WRITE_SAME w/ UNMAP=1 within
fd_execute_write_same_unmap() backend code.
If the FILEIO backend is normal file, the emulation uses fallocate to
punch hole to reclaim the free space used by the file. If the FILEIO
backend is block device, the emulation uses blkdev_issue_discard().
Tested with 512, 1k, 2k, and 4k block_sizes.
Changes in v2:
- Set the various dev->dev_attrib.*unmap* values (nab)
Cc: Christoph Hellwig <hch@lst.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Asias He <asias@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The callback function of call_rcu() just calls a kfree(), so we
can use kfree_rcu() instead of call_rcu() + callback function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Fix bit-clearing in login_rsp->flags for case 0.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The result from get_random_bytes should already be random, so further
manipulation and mixing should not be needed.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a bug where a handful of informational / control CDBs
that should be allowed during ALUA access state Standby/Offline/Transition
where incorrectly returning CHECK_CONDITION + ASCQ_04H_ALUA_TG_PT_*.
This includes INQUIRY + REPORT_LUNS, which would end up preventing LUN
registration when LUN scanning occured during these ALUA access states.
Cc: Hannes Reinecke <hare@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a regression introduced in v3.8-rc1 code where a failed
target_check_reservation() check in target_setup_cmd_from_cdb() was causing
an incorrect SAM_STAT_GOOD status to be returned during a WRITE operation
performed by an unregistered / unreserved iscsi initiator port.
This regression is only effecting iscsi-target due to a special case check
for TCM_RESERVATION_CONFLICT within iscsi_target_erl1.c:iscsit_execute_cmd(),
and was still correctly disallowing WRITE commands from backend submission
for unregistered / unreserved initiator ports, while returning the incorrect
SAM_STAT_GOOD status due to the missing SAM_STAT_RESERVATION_CONFLICT
assignment.
This regression was first introduced with:
commit de103c93af
Author: Christoph Hellwig <hch@lst.de>
Date: Tue Nov 6 12:24:09 2012 -0800
target: pass sense_reason as a return value
Go ahead and re-add the missing SAM_STAT_RESERVATION_CONFLICT assignment
during a target_check_reservation() failure, so that iscsi-target code
sends the correct SCSI status.
All other fabrics using target_submit_cmd_*() with a RESERVATION_CONFLICT
call to transport_generic_request_failure() are not effected by this bug.
Reported-by: Jeff Leung <jleung@curriegrad2004.ca>
Cc: Christoph Hellwig <hch@lst.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We can only have one page of data in each sg element, so we can not
cross a page boundary. Fail this case.
The 'while (len > 0 && data_len > 0) {}' loop is not necessary. The loop
can only be executed once.
Signed-off-by: Asias He <asias@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Paul Bolle