Tegra186 board under arm64 is using this device, according to
its dts file. So this patch enables its driver with a "=m" as
the other HWMON drivers.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable support for the TI HD3SS320 USB Type-C DRP Port controller driver
by turning on CONFIG_TYPEC and CONFIG_TYPEC_HD3SS3220 as modules.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Allwinner sun6i DMA drivers is used on A64 and H6 boards.
Enable it as a module.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The SUNXI_WATCHDOG option is required to make the
watchdog available on Allwinner H6.
Enable this option as a module.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The EK874 board comes with a TDA19988 chip on board, therefore
enable it in the defconfig.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Sid contains speedbin information and temperature sensor
calibration information and more, which are important for SOC.
This patch enables CONFIG_NVMEM_SUNXI_SID by default.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Enable mfd and regulator driver for PMIC found on imx8mm-evk boards
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The current lpi2c driver can work on imx8 chips so lets enable it. Also
enable few i2c peripherals found on imx8qxp-mek I2C (some were already
used for other boards).
Sensors enabled as modules because not required for boot.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Basic imx8mm support is already available in linux-next just not
enabled in arm64 defconfig. With this patch imx8mm-evk can boot.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8MQ needs it for RTC support.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable CONFIG_IMX_SC_WDT as module to support i.MX system
controller watchdog.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable the CONFIG_SPI_IMX option so that i.MX8M can use the
imx spi driver by default.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- Mostly the usual churn due to options being reordered or not added
in the right locations.
- Some various enabling of new drivers, etc.
... i.e. the usual updates, nothing particularly sticks out.
-----BEGIN PGP SIGNATURE-----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=IKfA
-----END PGP SIGNATURE-----
Merge tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC defconfig updates from Olof Johansson:
"Mostly the usual churn due to options being reordered or not added in
the right locations.
Some various enabling of new drivers, etc.
... i.e. the usual updates, nothing particularly sticks out"
* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (23 commits)
arm64: defconfig: Update UFSHCD for Hi3660 soc
ARM: multi_v7_defconfig: Enable support for STPMIC1
ARM: multi_v7_defconfig: Enable missing drivers for supported Chromebooks
arm64: defconfig: enable mv-xor driver
ARM: Enable Trusted Foundations for multiplatform ARM v7
ARM: tegra: Enable Trusted Foundations by default
ARM: tegra: Update default configuration for v5.1-rc1
ARM: multi_v7_defconfig: Update for moved options
ARM: multi_v7_defconfig: Update for dropped options
ARM: shmobile: Enable USB [EO]HCI HCD PLATFORM support in shmobile_defconfig
ARM: shmobile: Enable PHY_RCAR_GEN3_USB2 in shmobile_defconfig
ARM: qcom_defconfig: add options for LG Nexus 5 phone
arm64: defconfig: include the Agilex platform to the arm64 defconfig
arm64: defconfig: Add PWM Fan support
arm64: defconfig: Enable Tegra HDA support
ARM: multi_v7_defconfig: Enable support for CFI NOR FLASH
ARM: shmobile: defconfig: Enable support for CFI NOR FLASH
ARM: shmobile: defconfig: Refresh for v5.1-rc1
ARM: multi_v7_defconfig: enable the Amlogic Meson ADC and eFuse drivers
arm64: defconfig: enable fpga and service layer
...
- Document (kerneldoc) core mfd_add_devices() API
- New Drivers
- Add support for Altera SOCFPGA System Manager
- Add support for Maxim MAX77650/77651 PMIC
- Add support for Maxim MAX77663 PMIC
- Add support for ST Multi-Function eXpander (STMFX)
- New Device Support
- Add support for LEDs to Intel Cherry Trail Whiskey Cove PMIC
- Add support for RTC to SAMSUNG Electronics S2MPA01 PMIC
- Add support for SAM9X60 to Atmel HLCDC (High-end LCD Controller)
- Add support for USB X-Powers AXP 8xx PMICs
- Add support for Integrated Sensor Hub (ISH) to ChromeOS EC
- Add support for USB PD Logger to ChromeOS EC
- Add support for AXP223 to X-Powers AXP series PMICs
- Add support for Power Supply to X-Powers AXP 803 PMICs
- Add support for Comet Lake to Intel Low Power Subsystem
- Add support for Fingerprint MCU to ChromeOS EC
- Add support for Touchpad MCU to ChromeOS EC
- Move TI LM3532 support to LED
- New Functionality
- Add/extend DT support; max77650, max77620
- Add support for power-off; max77620
- Add support for clocking; syscon
- Add support for host sleep event; cros_ec
- Fix-ups
- Trivial; Formatting, spelling, etc; Kconfig, sec-core, ab8500-debugfs
- Remove unused functionality; rk808, da9063-*
- SPDX conversion; da9063-*, atmel-*,
- Adapt/add new register definitions; cs47l35-tables, cs47l90-tables, imx6q-iomuxc-gpr
- Fix-up DT bindings; ti-lmu, cirrus,lochnagar
- Simply obtaining driver data; ssbi, t7l66xb, tc6387xb, tc6393xb
- Bug Fixes
- Fix incorrect defined values; max77620, da9063
- Fix device initialisation; twl6040
- Reset device on init; intel-lpss
- Fix build warnings when !OF; sun6i-prcm
- Register OF match tables; tps65912-spi
- Fix DMI matching; intel_quark_i2c_gpio
-----BEGIN PGP SIGNATURE-----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=dTSD
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Framework:
- Document (kerneldoc) core mfd_add_devices() API
New Drivers:
- Altera SOCFPGA System Manager
- Maxim MAX77650/77651 PMIC
- Maxim MAX77663 PMIC
- ST Multi-Function eXpander (STMFX)
New Device Support:
- LEDs support in Intel Cherry Trail Whiskey Cove PMIC
- RTC support in SAMSUNG Electronics S2MPA01 PMIC
- SAM9X60 support in Atmel HLCDC (High-end LCD Controller)
- USB X-Powers AXP 8xx PMICs
- Integrated Sensor Hub (ISH) in ChromeOS EC
- USB PD Logger in ChromeOS EC
- AXP223 in X-Powers AXP series PMICs
- Power Supply in X-Powers AXP 803 PMICs
- Comet Lake in Intel Low Power Subsystem
- Fingerprint MCU in ChromeOS EC
- Touchpad MCU in ChromeOS EC
- Move TI LM3532 support to LED
New Functionality:
- max77650, max77620: Add/extend DT support
- max77620 power-off
- syscon clocking
- croc_ec host sleep event
Fix-ups:
- Trivial; Formatting, spelling, etc; Kconfig, sec-core, ab8500-debugfs
- Remove unused functionality; rk808, da9063-*
- SPDX conversion; da9063-*, atmel-*,
- Adapt/add new register definitions; cs47l35-tables, cs47l90-tables, imx6q-iomuxc-gpr
- Fix-up DT bindings; ti-lmu, cirrus,lochnagar
- Simply obtaining driver data; ssbi, t7l66xb, tc6387xb, tc6393xb
Bug Fixes:
- Fix incorrect defined values; max77620, da9063
- Fix device initialisation; twl6040
- Reset device on init; intel-lpss
- Fix build warnings when !OF; sun6i-prcm
- Register OF match tables; tps65912-spi
- Fix DMI matching; intel_quark_i2c_gpio"
* tag 'mfd-next-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (65 commits)
mfd: Use dev_get_drvdata() directly
mfd: cros_ec: Instantiate properly CrOS Touchpad MCU device
mfd: cros_ec: Instantiate properly CrOS FP MCU device
mfd: cros_ec: Update the EC feature codes
mfd: intel-lpss: Add Intel Comet Lake PCI IDs
mfd: lochnagar: Add links to binding docs for sound and hwmon
mfd: ab8500-debugfs: Fix a typo ("deubgfs")
mfd: imx6sx: Add MQS register definition for iomuxc gpr
dt-bindings: mfd: LMU: Fix lm3632 dt binding example
mfd: intel_quark_i2c_gpio: Adjust IOT2000 matching
mfd: da9063: Fix OTP control register names to match datasheets for DA9063/63L
mfd: tps65912-spi: Add missing of table registration
mfd: axp20x: Add USB power supply mfd cell to AXP803
mfd: sun6i-prcm: Fix build warning for non-OF configurations
mfd: intel-lpss: Set the device in reset state when init
platform/chrome: Add support for v1 of host sleep event
mfd: cros_ec: Add host_sleep_event_v1 command
mfd: cros_ec: Instantiate the CrOS USB PD logger driver
mfd: cs47l90: Make DAC_AEC_CONTROL_2 readable
mfd: cs47l35: Make DAC_AEC_CONTROL_2 readable
...
- Update the defconfig to enable the mv-xor driver found on the
Armada 3700
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCXL7CVgAKCRALBhiOFHI7
1VzpAJ4g2dWLtkB9F1YlPOMGzfZnAPamKACgjUMB8UM2+avwae6rdk6oa3qudSQ=
=gg0T
-----END PGP SIGNATURE-----
Merge tag 'mvebu-arm64-5.2-1' of git://git.infradead.org/linux-mvebu into arm/defconfig
mvebu arm64 for 5.2 (part 1)
- Update the defconfig to enable the mv-xor driver found on the
Armada 3700
* tag 'mvebu-arm64-5.2-1' of git://git.infradead.org/linux-mvebu:
arm64: defconfig: enable mv-xor driver
Signed-off-by: Olof Johansson <olof@lixom.net>
Just a single patch to enable our SPI controller on the arm64 defconfig.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXLmzPwAKCRDj7w1vZxhR
xdmbAP0WZ/2DSFexF4dkaRMcMfZ74b10mh4Yvn9usm6nUll3NAEA2IbdPWLK+/pk
ocj1Jwr4KHxHnMBXES1SQ6I9AYo9YAs=
=bA+y
-----END PGP SIGNATURE-----
Merge tag 'sunxi-config64-for-5.2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/defconfig
Allwinner arm64 defconfig changes for 5.2
Just a single patch to enable our SPI controller on the arm64 defconfig.
* tag 'sunxi-config64-for-5.2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: defconfig: Enable SPI_SUN6I
Signed-off-by: Olof Johansson <olof@lixom.net>
These patches enable PWM fan and Tegra HDA support in the 64-bit ARM
default configuration, so that these features are enabled by default.
-----BEGIN PGP SIGNATURE-----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=rrf3
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.2-arm64-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/defconfig
arm64: tegra: Default configuration updates for v5.2-rc1
These patches enable PWM fan and Tegra HDA support in the 64-bit ARM
default configuration, so that these features are enabled by default.
* tag 'tegra-for-5.2-arm64-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: defconfig: Add PWM Fan support
arm64: defconfig: Enable Tegra HDA support
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit 7ee7ef24d0 ("scsi: arm64: defconfig: enable configs for Hisilicon ufs")
set 'CONFIG_SCSI_UFS_HISI=y', but the configs it depends
on
(CONFIG_SCSI_HFSHCD_PLATFORM && CONFIG_SCSI_UFSHCD)
were left to being built as modules.
Commit 1f4fa50dd4 ("arm64: defconfig: Regenerate for v4.20") "fixed"
that by reverting to 'CONFIG_SCSI_UFS_HISI=m'.
Thing is, if the rootfs is stored in the on-board flash (which
is the "canonical" way of doing things), we either need these drivers
to be built-in, or we need to fiddle with an initramfs to access that
flash and eventually load the modules installed over there.
The former is the easiest, do that.
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The mv-xor DMA driver is used for the XOR engine found in the ARM64
Marvell Armada 3720 SoC, so it makes sense to have it enabled in the
arm64 defconfig. A recent boot-time regression was found in mv-xor,
which would have been more easily noticed with this driver enabled by
default.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
MTD_NAND is large and encloses much more than what the symbol is
actually used for: raw NAND. Clarify the symbol by naming it
MTD_RAW_NAND instead.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The Tegra194 Jetson AGX Xavier board includes a PWM based fan. Enable
PWM fan support in the ARM64 defconfig to support the fan on this board.
Please note that the device-tree PWM fan node is already present for
this board.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable support for Tegra HDA controller in the ARM64 defconfig which is
used by Tegra210, Tegra186 and Tegra194. Please note that the Tegra HDA
controller requires the HDA HDMI/DP codec driver and so enable this as
well.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable the Stratix10 System Manager by default.
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Enable FPGA framework, Intel Stratix10 SoC FPGA manager, Stratix10
service layer, and Altera Freeze Bridge drivers.
Intel Stratix10 service layer driver was added with commit 7ca5ce8965
("firmware: add Intel Stratix10 service layer driver").
Intel Stratix10 service layer provides kernel APIs for drivers to request
access to the secure features. Such features include FPGA programming,
remote status update, and read and write secure registers.
While clients of the service layer can be built as modules, the service
layer itself has to be configured as built-in. The service layer is
dependent on ARCH_STRATIX10.
Enabling Altera Freeze Bridge depends on commit 38cd7ad5bd
("fpga: altera_freeze_bridge: remove restriction to socfpga").
Signed-off-by: Richard Gong <richard.gong@intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Enable support for RX-8571/RX-8581 RTC by turning on
CONFIG_RTC_DRV_RX8581 as module.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable SUN6I SPI controller for Allwinner ARM64 SoC's.
This would helpful to setup spi flash, for another booting source.
mark it as static since it require during boot.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Two new additions to arm64's defconfig to support A64 boards.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXF1a8wAKCRDj7w1vZxhR
xYvJAQCpobGf96IZw2tNgyrz/7hd54ZjpYkkvAJuLK5wMHhHuAD/d2IBBVQ2yu5q
IX6Z40PXrKz43QFFszDThZy9tMqdng0=
=TfND
-----END PGP SIGNATURE-----
Merge tag 'sunxi-config64-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/defconfig
Allwinner arm64 defconfig changes for 5.1
Two new additions to arm64's defconfig to support A64 boards.
* tag 'sunxi-config64-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: defconfig: Enable SUN6I Camera sensor interface
arm64: defconfig: Enable I2C_GPIO
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Enable:
* PCM3168A support which is required for audio on Kingfisher daughterboards
* R-Car thermal support
* Gen3 PCIe PHY support
-----BEGIN PGP SIGNATURE-----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=gf/c
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm64-defconfig-for-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into arm/defconfig
Renesas ARM64 Based SoC Defconfig Updates for v5.1
Enable:
* PCM3168A support which is required for audio on Kingfisher daughterboards
* R-Car thermal support
* Gen3 PCIe PHY support
* tag 'renesas-arm64-defconfig-for-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: defconfig: select Kingfisher Sound related configs
arm64: defconfig: Enable R-Car thermal driver
arm64: defconfig: Enable CONFIG_PHY_RCAR_GEN3_PCIE
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Enables the TCU driver to be built into the kernel, so that the TCU can
be used as debug serial on Jetson Xavier. This also enables the MAX8973
regulator driver that is required for CPU frequency scaling on Tegra210.
-----BEGIN PGP SIGNATURE-----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=Xuyn
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.1-arm64-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/defconfig
arm64: tegra: Default configuration changes for v5.1-rc1
Enables the TCU driver to be built into the kernel, so that the TCU can
be used as debug serial on Jetson Xavier. This also enables the MAX8973
regulator driver that is required for CPU frequency scaling on Tegra210.
* tag 'tegra-for-5.1-arm64-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: defconfig: Enable Tegra TCU
arm64: defconfig: Enable MAX8973 regulator
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Enable a number of i.MX SoC and driver options in arm64 defconfig.
The built-in drivers include: clock, pinctrl, power domain, serial,
MBox, SCU, Ethernet, MMC, regulator and watchdog, which are mostly
essential for building an useful kernel image for i.MX8 platform,
booting with rootfs on NFS or eMMC.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcYqUwAAoJEFBXWFqHsHzOJnkH/2R0OT6zLykAAvG2grUjD73x
5VTEbvlSnSrOur0vBXEZfTi6l3mvtuXj3L9wEpIB9dKgOAgGflAOqRlib0xrwFXW
JRnzgckooeEpeMbj482gN2xUIbkAg7V8P15lhrkPIGKcGDwtc2o2uTfPRMyRKxRB
szH3xl+OR38snzqtuaPEvxdguE2ZW1fMRm8CqDq3nKYD21wYW6WB6S9MLlaYfD6k
RxtjEBCbUCV7OaN90HlXi/u7fkzwDgd9dN4M18DTgP59qWkZNmZ+HGj2Wf8a3Vgc
7E/cBL+W1fbcGto+j5H2wNHYzT4C9O9EKbskKOs/HW2zojxVfNXsBrXOLMreWMk=
=dPMN
-----END PGP SIGNATURE-----
Merge tag 'imx-defconfig-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/defconfig
i.MX defconfig updates for 5.1:
- Enable a number of i.MX SoC and driver options in arm64 defconfig.
The built-in drivers include: clock, pinctrl, power domain, serial,
MBox, SCU, Ethernet, MMC, regulator and watchdog, which are mostly
essential for building an useful kernel image for i.MX8 platform,
booting with rootfs on NFS or eMMC.
* tag 'imx-defconfig-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: defconfig: Add IMX2+ watchdog
arm64: defconfig: Enable PFUZE100 regulator
arm64: defconfig: enable NXP FlexSPI driver
arm64: defconfig: Add i.MX8MQ boot necessary configs
arm64: defconfig: add imx8qxp support
arm64: defconfig: add i.MX system controller RTC support
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This is needed to boot correctly from eMMC on the i.MX8MQ EVK board.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Tegra Combined UART is used on some Tegra194 devices as a way of
multiplexing output from multiple producers onto a single physical UART.
Enable this by default so that it can be used as the default console to
write kernel messages to.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra210 Smaug board uses MAX77621 for both CPU & GPU rail. Note
that max8973 and max77621 share the same driver. So enable this driver
for the PMIC.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable Camera sensor interface for Allwinner SUN6I SoC's.
This support enable V4L2 platform drivers static and
VIDEO_SUN6I_CSI as module.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The GPIO-based bitbanging I2C driver is required to configure
CSI data, clock pins on CSI block in Allwinner A64 SoC.
Let build it as module.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This switches out the old fbdev PL11x driver to the new
DRM driver in the Aarch64/ARM64 defconfig. Some ARM
reference designs use this IP with the Silicon Image
SII902x HDMI bridge so activate both.
The required DTS changes are already in-tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Compile the necessary drivers as modules, including codecs, for the
s400 sound card.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch selects PCM3168A which is needed for Kingfisher Sound
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable the R-Car thermal driver as a built-in.
This seems safer than enabling as a module from the point of view of
protecting equipment from overheating.
This driver is used in conjunction with the R-Car V3M (r8a77970),
E3 (r8a77990) and D3 (r8a77995) SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable R-Car Gen3 PCIe PHY support, which is needed for PCIe to function
on the Renesas Condor board.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
A few updates that we merged late but are low risk for regressions for
other platforms (and a few other straggling patches):
- I mis-tagged the 'drivers' branch, and missed 3 patches. Merged in
here. They're for a driver for the PL353 SRAM controller and a build
fix for the qualcomm scm driver.
- A new platform, RDA Micro RDA8810PL (Cortex-A5 w/ integrated Vivante
GPU, 256MB RAM, Wifi). This includes some acked platform-specific
drivers (serial, etc). This also include DTs for two boards with this
SoC, OrangePi 2G and OrangePi i86.
- i.MX8 is another new platform (NXP, 4x Cortex-A53 + Cortex-M4, 4K
video playback offload). This is the first i.MX 64-bit SoC.
- Some minor updates to Samsung boards (adding a few peripherals in
DTs).
- Small rework for SMP bootup on STi platforms.
- A couple of TEE driver fixes.
- A couple of new config options (bcm2835 thermal, Uniphier MDMAC)
enabled in defconfigs.
-----BEGIN PGP SIGNATURE-----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=qgZw
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull more ARM SoC updates from Olof Johansson:
"A few updates that we merged late but are low risk for regressions for
other platforms (and a few other straggling patches):
- I mis-tagged the 'drivers' branch, and missed 3 patches. Merged in
here. They're for a driver for the PL353 SRAM controller and a
build fix for the qualcomm scm driver.
- A new platform, RDA Micro RDA8810PL (Cortex-A5 w/ integrated
Vivante GPU, 256MB RAM, Wifi). This includes some acked
platform-specific drivers (serial, etc). This also include DTs for
two boards with this SoC, OrangePi 2G and OrangePi i86.
- i.MX8 is another new platform (NXP, 4x Cortex-A53 + Cortex-M4, 4K
video playback offload). This is the first i.MX 64-bit SoC.
- Some minor updates to Samsung boards (adding a few peripherals in
DTs).
- Small rework for SMP bootup on STi platforms.
- A couple of TEE driver fixes.
- A couple of new config options (bcm2835 thermal, Uniphier MDMAC)
enabled in defconfigs"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (27 commits)
ARM: multi_v7_defconfig: enable CONFIG_UNIPHIER_MDMAC
arm64: defconfig: Re-enable bcm2835-thermal driver
MAINTAINERS: Add entry for RDA Micro SoC architecture
tty: serial: Add RDA8810PL UART driver
ARM: dts: rda8810pl: Add interrupt support for UART
dt-bindings: serial: Document RDA Micro UART
ARM: dts: rda8810pl: Add timer support
ARM: dts: Add devicetree for OrangePi i96 board
ARM: dts: Add devicetree for OrangePi 2G IoT board
ARM: dts: Add devicetree for RDA8810PL SoC
ARM: Prepare RDA8810PL SoC
dt-bindings: arm: Document RDA8810PL and reference boards
dt-bindings: Add RDA Micro vendor prefix
ARM: sti: remove pen_release and boot_lock
arm64: dts: exynos: Add Bluetooth chip to TM2(e) boards
arm64: dts: imx8mq-evk: enable watchdog
arm64: dts: imx8mq: add watchdog devices
MAINTAINERS: add i.MX8 DT path to i.MX architecture
arm64: add support for i.MX8M EVK board
arm64: add basic DTS for i.MX8MQ
...
The bcm2835-thermal driver was added with commit ac178e4280
("ARM64: bcm2835: add thermal driver to default config"). Unfortunately
this was accidentally dropped by commit eb1e6716cc
("arm64: defconfig: sync with savedefconfig"). So enable the driver again.
Fixes: eb1e6716cc ("arm64: defconfig: sync with savedefconfig")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit e8342cc795 ("enable CAAM crypto engine on QorIQ DPAA2 SoCs")
enabled CRYPTO_DEV_FSL_DPAA2_CAAM, which depends on FSL_MC_DPIO,
which is not set. Enable FSL_MC_BUS, and build FSL_MC_DPIO and
CRYPTO_DEV_FSL_DPAA2_CAAM as modules.
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
[olof: refreshed due to churn]
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit e78d57b2f8 ("pinctrl: mediatek: add pinctrl-moore that
implements the generic pinctrl dt-bindings") made PINCTRL_MT7622
depend on PINCTRL_MTK_MOORE, so it fell off in the refresh.
Add MTK_MOORE, which automatically enables MT7622.
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
[olof: refresh and minor commit message reword]
Signed-off-by: Olof Johansson <olof@lixom.net>
Run the platform defconfig through kbuild, and handle the trivial case
where options merely move around.
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
[olof: refreshed due to some recent churn]
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Olof Johansson <olof@lixom.net>
A bunch of patches to improve the coverage of Allwinner drivers in the
arm64 defconfig, mostly targeted at adding display drivers support.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXAqBowAKCRDj7w1vZxhR
xVZMAQCfcR+ZJf0vqHJ2fR0nOroltxrs36wU/SutdePaHInQuAD/dfdXlVonEaGN
1VBKIGzl1Z9PNTsCGADLN0dQRLlX/Q4=
=Q2ck
-----END PGP SIGNATURE-----
Merge tag 'sunxi-config64-for-4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/defconfig
Allwinner arm64 defconfig for 4.21
A bunch of patches to improve the coverage of Allwinner drivers in the
arm64 defconfig, mostly targeted at adding display drivers support.
* tag 'sunxi-config64-for-4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: defconfig: Enable PWM_SUN4I
arm64: defconfig: Enable DRM_SUN8I_DW_HDMI
arm64: defconfig: Enable DRM_SUN8I_MIXER
arm64: defconfig: Enable MFD_AXP20X_I2C
Signed-off-by: Olof Johansson <olof@lixom.net>
Enable the GCC and PINCTRL for MSM8998 to make upstream boot to console.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Enable a few core config options to be able to boot SDM845 MTP.
The GCC, PINCTRL and GENI options are required to be able to boot to a
console. Several clocks from GCC are parented by the "bi_tcxo" clock
from the RPMH clock driver, so enable this to save others the time to
debug the missing parent clocks later. RPMH depends on the COMMAND_DB.
While we're enabling the others let's do RPMH regulators as well, as
everything beyond this point depends on that.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Enable remoteproc configs to boot the remoteprocs on QC chipsets. These
are common configs and not specific to a specific SoC so should be enabled
across the board.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Enable GCC and pin control configs to make it possible to boot the
QCS404 EVBs.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Allwinner PWM support need for ARM64 Allwinner SoC's
which used pwms, builds it as module.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner DesignWare HDMI is needed for HDMI support
in ARM64 Allwinner SoC's, build it as module.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner Display Engine 2.0 Mixer is need for ARM64
Allwinner SoC's, build it as module.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Allwinner H6 SoC is paired with the X-Powers AXP805 PMIC
connected via I2C.
Enable the driver for this PMIC.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # OPI-1+
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The arm64 port now runs on servers which use IPMI. This patch enables
relevant core configs to save manually enabling them when testing
mainline.
Signed-off-by: John Garry <john.garry@huawei.com>
[olof: Switched to =m instead of =y]
Signed-off-by: Olof Johansson <olof@lixom.net>
The defconfig changes are split out from the rest again. This time we
have a number of changes for NXP i.MX and Renesas, including a cleanup of
old options.
Some smaller changes are for Socionext Uniphier, Allwinner, Qualcomm,
Rockchip, Renesas, AT91, Hisilicon, and STM32. All of these just enable
platform specific device drivers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=cE9r
-----END PGP SIGNATURE-----
Merge tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC defconfig updates from Arnd Bergmann:
"The defconfig changes are split out from the rest again. This time we
have a number of changes for NXP i.MX and Renesas, including a cleanup
of old options.
Some smaller changes are for Socionext Uniphier, Allwinner, Qualcomm,
Rockchip, Renesas, AT91, Hisilicon, and STM32. All of these just
enable platform specific device drivers"
* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (40 commits)
arm64: defconfig: Enable SERIAL_8250_OMAP
arm64: defconfig: Enable TI_SCI related configs
ARM: imx_v6_v7_defconfig: Select CONFIG_TMPFS_POSIX_ACL
ARM: imx_v4_v5_defconfig: Remove unneeded options
ARM: imx_v4_v5_defconfig: Re-sync defconfig
ARM: mxs_defconfig: Remove unneeded options
ARM: mxs_defconfig: Re-sync defconfig
ARM: imx_v6_v7_defconfig: Remove unneeded options
ARM: imx_v6_v7_defconfig: Re-sync defconfig
ARM: imx_v6_v7_defconfig: select CONFIG_ARM_CPUIDLE by default
ARM: imx_v6_v7_defconfig: Make usbnet drivers builtin for boot
ARM: imx_v6_v7_defconfig: add CONFIG_FW_LOADER_USER_HELPER
ARM: imx_v6_v7_defconfig: Select CONFIG_SENSORS_MC13783_ADC
ARM: multi_v7_defconfig: enable CONFIG_MMC_UNIPHIER
arm64: defconfig: enable CONFIG_MMC_UNIPHIER
ARM: multi_v7_defconfig: Enable USB phys for UniPhier SoCs
arm64: defconfig: Enable USB phys for UniPhier SoCs
arm64: defconfig: enable Rockchip Innosilicon hdmiphy
arm64: defconfig: Enable PCIEPORTBUS
arm64: defconfig: enable HiSilicon HNS3 driver
...
Enable TI System Control Interface (TI_SCI) Message Protocol library
and it's relevant power management drivers using this library.
TI's AM6 SoC uses this TI_SCI library to communicate to its system
controller(DMSC). While at it, enable TI_MESSAGE_MANAGER mailbox driver
using which this communication happens.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Here is a single config change to enable the DRM driver in the arm64
defconfig.
-----BEGIN PGP SIGNATURE-----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=MBKv
-----END PGP SIGNATURE-----
Merge tag 'sunxi-config64-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/defconfig
Allwinner arm64 config changes for 4.20
Here is a single config change to enable the DRM driver in the arm64
defconfig.
* tag 'sunxi-config64-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: defconfig: Enable CONFIG_DRM_SUN4I
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Enable the USB3 and USB2 phys implemented in UniPhier SoCs.
These phys are necessary for dwc3 and ehci controllers driving
the USB ports on arm64 UniPhier SoCs.
Since the USB host drivers are already built-in, so only the phy
driver are missing to allow booting with USB devices.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The rk3228 and rk3328 socs use an MMIO-connected hdmi-phy from Innosilicon.
So enable the necessary driver as module.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
- Enable integrated NIC driver(hns3) for hisilicon SoCs
- Enable PCIe Port bus to support some PCIe features like
AER, hotplug, PME and DPC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Gn5v
-----END PGP SIGNATURE-----
Merge tag 'hisi-defconfig-for-4.20' of git://github.com/hisilicon/linux-hisi into next/defconfig
ARM64: hisilicon: defconfig updates for 4.20
- Enable integrated NIC driver(hns3) for hisilicon SoCs
- Enable PCIe Port bus to support some PCIe features like
AER, hotplug, PME and DPC
* tag 'hisi-defconfig-for-4.20' of git://github.com/hisilicon/linux-hisi:
arm64: defconfig: Enable PCIEPORTBUS
arm64: defconfig: enable HiSilicon HNS3 driver
Signed-off-by: Olof Johansson <olof@lixom.net>
PCIe features like AER, Hotplug, PME, DPC depend on PCIEPORTBUS,
so enable PCIEPORTBUS as default.
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Enable CAAM (Cryptographic Accelerator and Assurance Module) driver
for QorIQ Data Path Acceleration Architecture (DPAA) v2.
It handles DPSECI (Data Path SEC Interface) DPAA2 objects that sit
on the Management Complex (MC) fsl-mc bus.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Enable the Renesas RZ/G2E (R8A774C0) SoC in the ARM64 defconfig.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The QRTR packet family is used for a wide range of communication between
services in Qualcomm platforms. Examples of services using this
transport for communication are remoteproc management, modem control,
positioning, power management and WiFi.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Enable DRM Support for Allwinner Display Engine, built as a module.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Now that the scalar fallbacks have been moved out of this driver into
the core crc32()/crc32c() routines, we are left with a CRC32 crypto API
driver for arm64 that is based only on 64x64 polynomial multiplication,
which is an optional instruction in the ARMv8 architecture, and is less
and less likely to be available on cores that do not also implement the
CRC32 instructions, given that those are mandatory in the architecture
as of ARMv8.1.
Since the scalar instructions do not require the special handling that
SIMD instructions do, and since they turn out to be considerably faster
on some cores (Cortex-A53) as well, there is really no point in keeping
this code around so let's just remove it.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Enable the Renesas RZ/G2M (R8A774A1) SoC in the ARM64 defconfig.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
We keep these separate since some files are shared and conflict-prone,
but there isn't really much to write about here.
Some of the churnier pieces is for the Aspeed platforms, which did an
overdue refresh of the defconfig, and enabled USB gadget and some
drivers from there. Most of the rest are minor additions here and there
to turn on drivers that are needed or useful on the various platforms.
-----BEGIN PGP SIGNATURE-----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=t+qo
-----END PGP SIGNATURE-----
Merge tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC defconfig updates from Olof Johansson:
"We keep these separate since some files are shared and conflict-prone,
but there isn't really much to write about here.
Some of the churnier pieces is for the Aspeed platforms, which did an
overdue refresh of the defconfig, and enabled USB gadget and some
drivers from there. Most of the rest are minor additions here and
there to turn on drivers that are needed or useful on the various
platforms"
* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (39 commits)
ARM: multi_v7_defconfig: add CONFIG_UNIPHIER_THERMAL and CONFIG_SNI_AVE
ARM: config: aspeed: Enable new FSI drivers
ARM: config: multi_v5: Enable ASPEED drivers
ARM: config: multi_v5: Refresh configuration
ARM: config: aspeed: Update defconfig
ARM: multi_v7_defconfig: Enable support for RZN1D-DB
ARM: shmobile: defconfig: Disable /sbin/hotplug fork-bomb
ARM: shmobile: defconfig: Enable support for RZN1D-DB
ARM: shmobile: defconfig: Enable reset controller support
ARM: shmobile: defconfig: Drop NET_VENDOR_<FOO>=n
arm64: defconfig: Enable more peripherals for Samsung Chromebook Plus.
arm64: defconfig: Enable CONFIG_MTD_NAND_QCOM for IPQ8074
ARM: qcom_defconfig: Enable QCOM NAND related configs
ARM: imx_v6_v7_defconfig: add DMATEST support
ARM: mvebu_v7_defconfig: enable SFP support
ARM: mvebu_v7_defconfig: sync defconfig
ARM: multi_v7_defconfig: Add Marvell NAND controller support
arm: configs: Add USB gadget to Aspeed G5 defconfig
arm: configs: Add USB gadget to Aspeed G4 defconfig
arm64: defconfig: enable HiSilicon PMU driver
...
- Add Cirrus Logic Madera Codec (CS47L35, CS47L85 and CS47L90/91) driver
- Add ChromeOS EC CEC driver
- Add ROHM BD71837 PMIC driver
- New Device Support
- Add support for Dialog Semi DA9063L PMIC variant to DA9063
- Add support for Intel Ice Lake to Intel-PLSS-PCI
- Add support for X-Powers AXP806 to AXP20x
- New Functionality
- Add support for USB Charging to the ChromeOS Embedded Controller
- Add support for HDMI CEC to the ChromeOS Embedded Controller
- Add support for HDMI CEC to Intel HDMI
- Add support for accessory detection to Madera devices
- Allow individual pins to be configured via DT' wlf,csnaddr-pd
- Provide legacy platform specific EEPROM/Watchdog commands; rave-sp
- Fix-ups
- Trivial renaming/spelling fixes; cros_ec, da9063-*
- Convert to Managed Resources (devm_*); da9063-*, ti_am335x_tscadc
- Transition to helper macros/functions; da9063-*
- Constify; kempld-core
- Improve error path/messages; wm8994-core
- Disable IRQs locally instead of relying on USB subsystem; dln2
- Remove unused code; rave-sp
- New exports; sec-core
- Bug Fixes
- Fix possible false I2C transaction error; arizona-core
- Fix declared memory area size; hi655x-pmic
- Fix checksum type; rave-sp
- Fix incorrect default serial port configuration: rave-sp
- Fix incorrect coherent DMA mask for sub-devices; sm501
-----BEGIN PGP SIGNATURE-----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=4Yj4
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Add Cirrus Logic Madera Codec (CS47L35, CS47L85 and CS47L90/91) driver
- Add ChromeOS EC CEC driver
- Add ROHM BD71837 PMIC driver
New Device Support:
- Add support for Dialog Semi DA9063L PMIC variant to DA9063
- Add support for Intel Ice Lake to Intel-PLSS-PCI
- Add support for X-Powers AXP806 to AXP20x
New Functionality:
- Add support for USB Charging to the ChromeOS Embedded Controller
- Add support for HDMI CEC to the ChromeOS Embedded Controller
- Add support for HDMI CEC to Intel HDMI
- Add support for accessory detection to Madera devices
- Allow individual pins to be configured via DT' wlf,csnaddr-pd
- Provide legacy platform specific EEPROM/Watchdog commands; rave-sp
Fix-upsL
- Trivial renaming/spelling fixes; cros_ec, da9063-*
- Convert to Managed Resources (devm_*); da9063-*, ti_am335x_tscadc
- Transition to helper macros/functions; da9063-*
- Constify; kempld-core
- Improve error path/messages; wm8994-core
- Disable IRQs locally instead of relying on USB subsystem; dln2
- Remove unused code; rave-sp
- New exports; sec-core
Bug Fixes:
- Fix possible false I2C transaction error; arizona-core
- Fix declared memory area size; hi655x-pmic
- Fix checksum type; rave-sp
- Fix incorrect default serial port configuration: rave-sp
- Fix incorrect coherent DMA mask for sub-devices; sm501"
* tag 'mfd-next-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (60 commits)
mfd: madera: Add register definitions for accessory detect
mfd: sm501: Set coherent_dma_mask when creating subdevices
mfd: bd71837: Devicetree bindings for ROHM BD71837 PMIC
mfd: bd71837: Core driver for ROHM BD71837 PMIC
media: platform: cros-ec-cec: Fix dependency on MFD_CROS_EC
mfd: sec-core: Export OF module alias table
mfd: as3722: Disable auto-power-on when AC OK
mfd: axp20x: Support AXP806 in I2C mode
mfd: axp20x: Add self-working mode support for AXP806
dt-bindings: mfd: axp20x: Add "self-working" mode for AXP806
mfd: wm8994: Allow to configure CS/ADDR Pulldown from dts
mfd: wm8994: Allow to configure Speaker Mode Pullup from dts
mfd: rave-sp: Emulate CMD_GET_STATUS on device that don't support it
mfd: rave-sp: Add legacy watchdog ping command translation
mfd: rave-sp: Add legacy EEPROM access command translation
mfd: rave-sp: Initialize flow control and parity of the port
mfd: rave-sp: Fix incorrectly specified checksum type
mfd: rave-sp: Remove unused defines
mfd: hi655x: Fix regmap area declared size for hi655x
mfd: ti_am335x_tscadc: Fix struct clk memory leak
...
This is mostly updates to the usual drivers: mpt3sas, lpfc, qla2xxx,
hisi_sas, smartpqi, megaraid_sas, arcmsr. In addition, with the
continuing absence of Nic we have target updates for tcmu and target
core (all with reviews and acks). The biggest observable change is
going to be that we're (again) trying to switch to mulitqueue as the
default (a user can still override the setting on the kernel command
line). Other major core stuff is the removal of the remaining
Microchannel drivers, an update of the internal timers and some
reworks of completion and result handling.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCW3R3niYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishauRAP4yfBKK
dbxF81c/Bxi/Stk16FWkOOrjs4CizwmnMcpM5wD/UmM9o6ebDzaYpZgA8wIl7X/N
o/JckEZZpIp+5NySZNc=
=ggLB
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates to the usual drivers: mpt3sas, lpfc, qla2xxx,
hisi_sas, smartpqi, megaraid_sas, arcmsr.
In addition, with the continuing absence of Nic we have target updates
for tcmu and target core (all with reviews and acks).
The biggest observable change is going to be that we're (again) trying
to switch to mulitqueue as the default (a user can still override the
setting on the kernel command line).
Other major core stuff is the removal of the remaining Microchannel
drivers, an update of the internal timers and some reworks of
completion and result handling"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (203 commits)
scsi: core: use blk_mq_run_hw_queues in scsi_kick_queue
scsi: ufs: remove unnecessary query(DM) UPIU trace
scsi: qla2xxx: Fix issue reported by static checker for qla2x00_els_dcmd2_sp_done()
scsi: aacraid: Spelling fix in comment
scsi: mpt3sas: Fix calltrace observed while running IO & reset
scsi: aic94xx: fix an error code in aic94xx_init()
scsi: st: remove redundant pointer STbuffer
scsi: qla2xxx: Update driver version to 10.00.00.08-k
scsi: qla2xxx: Migrate NVME N2N handling into state machine
scsi: qla2xxx: Save frame payload size from ICB
scsi: qla2xxx: Fix stalled relogin
scsi: qla2xxx: Fix race between switch cmd completion and timeout
scsi: qla2xxx: Fix Management Server NPort handle reservation logic
scsi: qla2xxx: Flush mailbox commands on chip reset
scsi: qla2xxx: Fix unintended Logout
scsi: qla2xxx: Fix session state stuck in Get Port DB
scsi: qla2xxx: Fix redundant fc_rport registration
scsi: qla2xxx: Silent erroneous message
scsi: qla2xxx: Prevent sysfs access when chip is down
scsi: qla2xxx: Add longer window for chip reset
...
(Chromebook Plus)
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAltfHfEQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgUzjCACqE5AOVnEk1y9RuyTT1AqfuH6SkAHzw+7n
QnEtfpHTmSP2SMWXUBreebr0YgHDXmyOLWsKO0dIg9kjLcqV2HKIZmHWy6i5ADEu
nvexKJ2YJ51MnzAaWXS08en49nV+pDJmLnNK0eeozGOw3qHqYo7f9AiweBQoHq7D
IZZetI57wiSSrWVD122T8XZQfw9OCYwvBtEYJMOcsUDm89JECDZNgn3mvFr8pzRM
FbGzkWoYJaySlfm/nGyVOZvPgcYymIOzVIxZej26vqa1//5WojAlw5tTvKZ3Jd9i
aR/i4ljxXmHbY3qVu1zgac+aYKMFWLeM5SV0WB5cWo0DYkkMrTC4
=FNsc
-----END PGP SIGNATURE-----
Merge tag 'v4.19-rockchip-defconfig64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/defconfig
Enablement of some more features relevant to rk3399-kevin
(Chromebook Plus)
* tag 'v4.19-rockchip-defconfig64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: defconfig: Enable more peripherals for Samsung Chromebook Plus.
Signed-off-by: Olof Johansson <olof@lixom.net>
Enable the Rockchip sound driver with MAX98357A/RT5514/DA7219 codecs,
Infineon TPM security chip (compliant with TCG TIS 1.2 TPM specification),
vctrl regulators for dynamic CPU voltages, UVC camera support and SBS-
compliant gas gauges needed for the Samsung Chromebook Plus.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
* Enable BD9571MWV regulator in ARM64 defconfig
This is to allow wider testing of the BD9571 PMIC which is
present on boards with Renesas R-Car Gen3 SoCs
-----BEGIN PGP SIGNATURE-----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=BkCA
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm64-defconfig-for-v4.19' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/defconfig
Renesas ARM64 Based SoC Defconfig Updates for v4.19
* Enable BD9571MWV regulator in ARM64 defconfig
This is to allow wider testing of the BD9571 PMIC which is
present on boards with Renesas R-Car Gen3 SoCs
* tag 'renesas-arm64-defconfig-for-v4.19' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: defconfig: Enable BD9571MWV regulator
Signed-off-by: Olof Johansson <olof@lixom.net>
QCOM IPQ8074 boards contain NAND flash memory for which
this config needs to be enabled.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
for 4.19, please pull the following changes:
- Stefan enables the Raspberry Pi voltage sensor driver (HWMON) in the
arm64 defconfig file
- Ray enables the ARM SP805 watchdog driver in the arm64 defconfig file
-----BEGIN PGP SIGNATURE-----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=DLo+
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.19/defconfig-arm64' of https://github.com/Broadcom/stblinux into next/defconfig
This pull request contains Broadcom ARM64-based SoCs defconfig changes
for 4.19, please pull the following changes:
- Stefan enables the Raspberry Pi voltage sensor driver (HWMON) in the
arm64 defconfig file
- Ray enables the ARM SP805 watchdog driver in the arm64 defconfig file
* tag 'arm-soc/for-4.19/defconfig-arm64' of https://github.com/Broadcom/stblinux:
arm64: defconfig: add CONFIG_ARM_SP805_WATCHDOG
arm64: defconfig: Enable RPi voltage sensor
Signed-off-by: Olof Johansson <olof@lixom.net>
The cros-ec I2C and SPI transport drivers have been moved from MFD
subsystem to platform/chrome, at the same time, the config symbol has
been renamed and lost the MFD_ prefix, so update all configs to the new
config symbol name.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Benson Leung <bleung@chromium.org>
The defconfig has drifted over time, as Kconfig entries have changed order
or default values. Several maintainers ended up running 'savedefconfig'
themselves which caused a cascade of conflicts. Let's do it once and
for all in our tree before -rc2 instead.
Signed-off-by: Olof Johansson <olof@lixom.net>
The patch enables the hwmon driver for the Raspberry Pi.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Nicolin Chen