If a register range is named then provide a debugfs file showing the
contents of the range separately.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rather than just returning a single error code for every possible thing we
can notice print an error message saying what the problem was. This makes
it very much easier to figure out what's wrong and fix it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This makes things consistent with the rest of the API and is actually what
the documentation says. We don't currently have any in tree users so low
cost.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is useful for integration with other subsystems, especially MFD,
and provides an alternative API for users that request their own IRQs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The primary handler will NOT be called if the interrupt nests into
another interrupt thread. Remove it to avoid confusing.
Signed-off-by: Yunfan Zhang <yfzhang@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently, regmap will write 1 to mask_base to mask
an interrupt and write 0 to unmask it.
But some chips do not have an interrupt mask register,
and only have interrupt enable register.
Then we should write 0 to disable interrupt and 1 to enable.
So add an mask_invert flag to handle this.
If it is not set, behavior is same as previous.
If set it to 1, the mask value will be inverted
before written to mask_base
Signed-off-by: Xiaofan Tian <tianxf@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some devices need to have a runtime PM reference while handling interrupts
to ensure that the register I/O is available. Support this with a flag in
the chip.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The kerneldoc for irq_set_irq_wake() says:
Enable/disable power management wakeup mode, which is
disabled by default.
regmap_irq_set_wake() clears bits to enable wake for an interrupt,
and sets bits to disable wake. Hence, we should set all bits in
wake_buf initially, to mirror the expected disabled state.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If a regmap-irq chip has no wake base:
* There's no point calling .irq_set_wake, hence IRQCHIP_SKIP_SET_WAKE.
* If some IRQs in the chip are enabled for wake and some aren't, we
should mask those interrupts that are not wake enabled, so that if
they occur during suspend, the system is not awoken. Hence,
IRQCHIP_MASK_ON_SUSPEND.
Note that IRQCHIP_MASK_ON_SUSPEND is handled by check_wakeup_irqs(),
which always iterates over every single interrupt in the system,
irrespective of whether an interrupt is a child of a controller whose
output interrupt has no wake-enabled inputs and hence is presumably
masked itself. Hence this change might cause interrupt unnecessary
masking operations and associated register I/O.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is intended to give each irq_chip a useful name, rather than hard-
coding them all as "regmap".
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This will allow later patches to adjust portions of the irq_chip
individually for each regmap_irq_chip that is created.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Don't write the full register, it's possible there's bits other than the
masks in the same register which we shouldn't be changing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
A number of places in the code were printing error messages that included
the address of a register, but were not calculating the register address
in the same way as the access to the register. Use a temporary to solve
this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When bus->fast_io is set, the locking here is done with spinlocks.
This is currently true for the regmap-mmio bus implementation.
While holding a spinlock we can't go to sleep, various operations
like removing the debugfs entries or re-initializing the cache will
sleep, therefore, shift the locking up to the user.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Sometimes for failures during very early init the trace infrastructure
isn't available early enough to be used. For this sort of problem
defining LOG_DEVICE will add printks for basic register I/O on a specific
device, allowing trace to be extracted when the trace system doesn't come
up early enough to work with.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
After page update, orginal work_buf has to be restored regardless of
the result.
Signed-off-by: Krystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Devices with register paging or indirectly accessed registers can configure
register mapping to map those on virtual address range. During access to
virtually mapped register range, indirect addressing is processed
automatically, in following steps:
1. selector for page or indirect register is updated (when needed);
2. register in data window is accessed.
Configuration should provide minimum and maximum register for virtual range,
details of selector field for page selection, minimum and maximum register of
data window for indirect access.
Virtual range registers are managed by cache as well as direct access
registers. In order to make indirect access more efficient, selector register
should be declared as non-volatile, if possible.
struct regmap_config is extended with the following:
struct regmap_range_cfg *ranges;
unsigned int n_ranges;
[Also reordered debugfs init to later on since the cleanup code was
conflicting with the new cleanup code for ranges anyway -- broonie]
Signed-off-by: Krystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Locks are moved to regmap_update_bits(), which allows to reenter internal
function _regmap_update_bits() from inside of regmap read/write routines.
Signed-off-by: Krystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
regmap_mmio_gen_context() is only used in regmap-mmio.c. Thus make it static.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow chips to provide a bank of registers for controlling the wake state
in a similar fashion to the masks and propagate the wake count to the
parent interrupt controller.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If the driver supplied an empty entry in the array of IRQs then return
an error rather than trying to do the mapping. This is intended for use
with handling chip variants and similar situations.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The word to be transmitted/received via regmap is composed by the following
parts:
config->reg_bits
config->val_bits
config->pad_bits
,so the total size should be calculated by summing up the number of bits of
each element and using a DIV_ROUND_UP to return the number of bytes.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If debugfs isn't cleaned up, stale files will be left in the filesystem
which will cause an OOPS when accessed the first time, and hang the
accessing application when accessed again, presumably due to some lock
being left held.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This will avoid the regmap core converting all addresses and values into
big endian, only for the mmio bus driver to have to convert them back to
native endian.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add a field to struct regmap_bus that allows bus drivers to request that
register addresses and values be formatted with a specific endianness.
The default endianness is unchanged from current operation: Big.
Implement native endian formatting/parsing for 16- and 32-bit values.
This will be enough to support regmap-mmio.c.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since there are uses for I2C_M_NOSTART which are much more sensible and
standard than most of the protocol mangling functionality (the main one
being gather writes to devices where something like a register address
needs to be inserted before a block of data) create a new I2C_FUNC_NOSTART
for this feature and update all the users to use it.
Also strengthen the disrecommendation of the protocol mangling while we're
at it.
In the case of regmap-i2c we remove the requirement for mangling as
I2C_M_NOSTART is the only mangling feature which is being used.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Ensure that we can't get randconfig breakage by doing the IRQ_DOMAIN
select automatically. Don't just do the select from REGMAP_IRQ to ensure
that the select actually gets noticed.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In some chips the IRQ status registers are not contiguous in the register
map but spaced at even spaces. This is an easy case to handle with minor
changes. It is assume for this purpose that the stride for status is
equal to the stride for mask/ack registers as well.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This gets us up to date with the recommended current kernel infrastructure
and should transparently give us device tree interrupt bindings for any
devices using the framework. If an explicit IRQ mapping is passed in then
a legacy interrupt range is created, otherwise a simple linear mapping is
used. Previously a mapping was mandatory so existing drivers should not
be affected.
A function regmap_irq_get_virq() is provided to allow drivers to map
individual IRQs which should be used in preference to the existing
regmap_irq_chip_get_base() which is only valid if a legacy IRQ range is
provided.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is a last minute bug fix that was only just noticed since the code
path that's being exercised here is one that is fairly rarely used. The
changelog for the change itself is extremely clear and the code itself
is obvious to inspection so should be pretty safe.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=xcal
-----END PGP SIGNATURE-----
Merge tag 'regmap-3.4' into regmap-stride
regmap: Last minute bug fix for 3.4
This is a last minute bug fix that was only just noticed since the code
path that's being exercised here is one that is fairly rarely used. The
changelog for the change itself is extremely clear and the code itself
is obvious to inspection so should be pretty safe.
Conflicts:
drivers/base/regmap/regmap.c (overlap between the fix and stride code)
The function regmap_bulk_read() calls the regmap_read() for
each register if set of register has volatile and cache is
enabled. In this case, last few register read makes the memory
corruption if the register size is not the size of unsigned int.
The regam_read() takes argument as unsigned int for returning
value and it update the value as
*val = map->format.parse_val(map->work_buf);
This causes complete 4 bytes (size of unsigned int) to get written.
Now if client pass the memory pointer for value which is equal to the
required size of register count in regmap_bulk_read() then last few
register read actually update the memory beyond passed pointer size.
Avoid this by using local variable for read and then do memcpy()
for actual byte copy to passed pointer based on register size.
I allocated one pointer ptr and take first 16 bytes dump of that
pointer then call regmap_bulk_read() with pointer which is just
on top of this allocated pointer and register count of 128. Here
register size is 1 byte.
The memory trace of last 5 register read are as follows:
[ 5.438589] regmap_bulk_read after regamp_read() for register 122
[ 5.447421] 0xef993c20 0xef993c00 0x00000000 0x00000001
[ 5.467535] regmap_bulk_read after regamp_read() for register 123
[ 5.476374] 0xef993c20 0xef993c00 0x00000000 0x00000001
[ 5.496425] regmap_bulk_read after regamp_read() for register 124
[ 5.505260] 0xef993c20 0xef993c00 0x00000000 0x00000001
[ 5.525372] regmap_bulk_read after regamp_read() for register 125
[ 5.534205] 0xef993c00 0xef993c00 0x00000000 0x00000001
[ 5.554258] regmap_bulk_read after regamp_read() for register 126
[ 5.563100] 0xef990000 0xef993c00 0x00000000 0x00000001
[ 5.554258] regmap_bulk_read after regamp_read() for register 127
[ 5.587108] 0xef000000 0xef993c00 0x00000000 0x00000001
Here it is observed that the memory content at first word started changing
on last 3 regmap_read() and so corruption happened.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use devres to implement dev_get_regmap(). This should mean that in almost
all cases devices wishing to take advantage of framework features based on
regmap shouldn't need to explicitly pass the regmap into the framework.
This simplifies device setup a bit.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Set the use_single_rw flag for devices that use format_write() since
format_write() doesn't support any form of block operation.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some devices does not support bulk read and write operations, for them
we have series of single write and read operations.
Signed-off-by: Anthony Olech <Anthony.Olech@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
[Fixed coding style, don't check use_single_rw before assign --broonie ]
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If we don't have a cached value for a register and we can cache it then
when we do a read a value we should add it to the cache to save rereading
it later on. Do this for single register reads, for block reads the code
would be a little more complex and this covers most practical usage.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit f01ee60fff ("regmap: implement register striding") caused the
compile errors below. Fix them.
drivers/base/regmap/regmap-irq.c: In function 'regmap_irq_sync_unlock':
drivers/base/regmap/regmap-irq.c:62:12: error: 'map' undeclared (first use in this function)
drivers/base/regmap/regmap-irq.c:62:12: note: each undeclared identifier is reported only once for each function it appears in
drivers/base/regmap/regmap-irq.c: In function 'regmap_irq_enable':
drivers/base/regmap/regmap-irq.c:77:37: error: 'map' undeclared (first use in this function)
drivers/base/regmap/regmap-irq.c: In function 'regmap_irq_disable':
drivers/base/regmap/regmap-irq.c:85:37: error: 'map' undeclared (first use in this function)
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
regmap_config.reg_stride is introduced. All extant register addresses
are a multiple of this value. Users of serial-oriented regmap busses will
typically set this to 1. Users of the MMIO regmap bus will typically set
this based on the value size of their registers, in bytes, so 4 for a
32-bit register.
Throughout the regmap code, actual register addresses are used. Wherever
the register address is used to index some array of values, the address
is divided by the stride to determine the index, or vice-versa. Error-
checking is added to all entry-points for register address data to ensure
that register addresses actually satisfy the specified stride. The MMIO
bus ensures that the specified stride is large enough for the register
size.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit 79c64d5 "regmap: allow regmap instances to be named" changed the
prototype of regmap_debugfs_init, but didn't update the dummy inline used
when !CONFIG_DEBUGFS. Fix this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some devices have multiple separate register regions. Logically, one
regmap would be created per region. One issue that prevents this is that
each instance will attempt to create the same debugfs files. Avoid this
by allowing regmaps to be named, and use the name to construct the
debugfs directory name.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Two more small fixes:
- Now we have users for it that aren't running Android it turns out that
regcache_sync_region() is much more useful to drivers if it's exported
for use by modules. Who knew?
- Make sure we don't divide by zero when doing debugfs dumps of rbtrees,
not visible up until now because everything was providing at least
some cache on startup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=qm1Q
-----END PGP SIGNATURE-----
Merge tag 'regmap-3.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull two more small regmap fixes from Mark Brown:
- Now we have users for it that aren't running Android it turns out
that regcache_sync_region() is much more useful to drivers if it's
exported for use by modules. Who knew?
- Make sure we don't divide by zero when doing debugfs dumps of
rbtrees, not visible up until now because everything was providing at
least some cache on startup.
* tag 'regmap-3.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: prevent division by zero in rbtree_show
regmap: Export regcache_sync_region()
val_len should be a multiple of val_bytes. If it's not, error out early.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
These error checks are implemented in regmap core. Remove the duplicate
code from regmap-mmio.c
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some of the error conditions detected by regmap_mmio_*() are pure internal
errors, rather than user-/client-triggerable conditions. Convert these to
BUG().
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is a basic memory-mapped-IO bus for regmap. It has the following
features and limitations:
* Registers themselves may be 8, 16, 32, or 64-bit. 64-bit is only
supported on 64-bit platforms.
* Register offsets are limited to precisely 32-bit.
* IO is performed using readl/writel, with no provision for using the
__raw_readl or readl_relaxed variants.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some bus types have very fast IO. For these, acquiring a mutex for every
IO operation is a significant overhead. Allow busses to indicate their IO
is fast, and enhance regmap to use a spinlock for those busses.
[Currently limited to native endian registers -- broonie]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The only context needed by I2C and SPI bus definitions is the device
itself; this can be converted to an i2c_client or spi_device in order
to perform IO on the device. However, other bus types may need more
context in order to perform IO. Enable this by having regmap_init accept
a bus_context parameter, and pass this to all bus callbacks. The
existing callbacks simply pass the struct device here. Future bus types
may pass something else.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Merge batch of fixes from Andrew Morton:
"The simple_open() cleanup was held back while I wanted for laggards to
merge things.
I still need to send a few checkpoint/restore patches. I've been
wobbly about merging them because I'm wobbly about the overall
prospects for success of the project. But after speaking with Pavel
at the LSF conference, it sounds like they're further toward
completion than I feared - apparently davem is at the "has stopped
complaining" stage regarding the net changes. So I need to go back
and re-review those patchs and their (lengthy) discussion."
* emailed from Andrew Morton <akpm@linux-foundation.org>: (16 patches)
memcg swap: use mem_cgroup_uncharge_swap fix
backlight: add driver for DA9052/53 PMIC v1
C6X: use set_current_blocked() and block_sigmask()
MAINTAINERS: add entry for sparse checker
MAINTAINERS: fix REMOTEPROC F: typo
alpha: use set_current_blocked() and block_sigmask()
simple_open: automatically convert to simple_open()
scripts/coccinelle/api/simple_open.cocci: semantic patch for simple_open()
libfs: add simple_open()
hugetlbfs: remove unregister_filesystem() when initializing module
drivers/rtc/rtc-88pm860x.c: fix rtc irq enable callback
fs/xattr.c:setxattr(): improve handling of allocation failures
fs/xattr.c:listxattr(): fall back to vmalloc() if kmalloc() failed
fs/xattr.c: suppress page allocation failure warnings from sys_listxattr()
sysrq: use SEND_SIG_FORCED instead of force_sig()
proc: fix mount -t proc -o AAA
Many users of debugfs copy the implementation of default_open() when
they want to support a custom read/write function op. This leads to a
proliferation of the default_open() implementation across the entire
tree.
Now that the common implementation has been consolidated into libfs we
can replace all the users of this function with simple_open().
This replacement was done with the following semantic patch:
<smpl>
@ open @
identifier open_f != simple_open;
identifier i, f;
@@
-int open_f(struct inode *i, struct file *f)
-{
(
-if (i->i_private)
-f->private_data = i->i_private;
|
-f->private_data = i->i_private;
)
-return 0;
-}
@ has_open depends on open @
identifier fops;
identifier open.open_f;
@@
struct file_operations fops = {
...
-.open = open_f,
+.open = simple_open,
...
};
</smpl>
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If there are no nodes in the cache, nodes will be 0, so calculating
"registers / nodes" will cause division by zero.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
regcache_sync_region() isn't going to be useful to most drivers if we
don't export it since otherwise they can't use it when built modular.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This change combines any padding bits into the register address bits when
determining register format handlers to use the next byte-divisible
register size.
A reg_shift member is introduced to the regmap struct to enable fixup
of the reg format.
Format handlers now take an extra parameter specifying the number of
bits to shift the value by.
Signed-off-by: Marc Reilly <marc@cpdesign.com.au>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add support for devices with 24 data bits.
Signed-off-by: Marc Reilly <marc@cpdesign.com.au>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The code currently passes the register offset in the current block to
regcache_lookup_reg. This works fine as long as there is only one block and with
base register of 0, but in all other cases it will look-up the default for a
wrong register, which can cause unnecessary register writes. This patch fixes
it by passing the actual register number to regcache_lookup_reg.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: <stable@vger.kernel.org>
"[RFC PATCH 0/2] audit of linux/device.h users in include/*"
https://lkml.org/lkml/2012/3/4/159
--
Nearly every subsystem has some kind of header with a proto like:
void foo(struct device *dev);
and yet there is no reason for most of these guys to care about the
sub fields within the device struct. This allows us to significantly
reduce the scope of headers including headers. For this instance, a
reduction of about 40% is achieved by replacing the include with the
simple fact that the device is some kind of a struct.
Unlike the much larger module.h cleanup, this one is simply two
commits. One to fix the implicit <linux/device.h> users, and then
one to delete the device.h includes from the linux/include/ dir
wherever possible.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=3j4+
-----END PGP SIGNATURE-----
Merge tag 'device-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull <linux/device.h> avoidance patches from Paul Gortmaker:
"Nearly every subsystem has some kind of header with a proto like:
void foo(struct device *dev);
and yet there is no reason for most of these guys to care about the
sub fields within the device struct. This allows us to significantly
reduce the scope of headers including headers. For this instance, a
reduction of about 40% is achieved by replacing the include with the
simple fact that the device is some kind of a struct.
Unlike the much larger module.h cleanup, this one is simply two
commits. One to fix the implicit <linux/device.h> users, and then one
to delete the device.h includes from the linux/include/ dir wherever
possible."
* tag 'device-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
device.h: audit and cleanup users in main include dir
device.h: cleanup users outside of linux/include (C files)
Remove for_each_set_bit_cont() after confirming that no one uses
for_each_set_bit_cont() anymore.
[sfr@canb.auug.org.au: regmap: cope with bitops API change]
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For files that are actively using linux/device.h, make sure
that they call it out. This will allow us to clean up some
of the implicit uses of linux/device.h within include/*
without introducing build regressions.
Yes, this was created by "cheating" -- i.e. the headers were
cleaned up, and then the fallout was found and fixed, and then
the two commits were reordered. This ensures we don't introduce
build regressions into the git history.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
[Fix for breakage which will be introduced during the merge window via
header reworks in another tree, the regmap tree does include device.h
but Paul's tree breaks that. Reworded subject to reflect -- broonie]
regmap.s uses devres_alloc() and others that are prototyped in device.h.
Include that to solve the following:
drivers/base/regmap/regmap.c: In function 'devm_regmap_init':
drivers/base/regmap/regmap.c:331:2: error: implicit declaration of function 'devres_alloc' [-Werror=implicit-function-declaration]
drivers/base/regmap/regmap.c:338:3: error: implicit declaration of function 'devres_add' [-Werror=implicit-function-declaration]
drivers/base/regmap/regmap.c:340:3: error: implicit declaration of function 'devres_free' [-Werror=implicit-function-declaration]
drivers/base/regmap/regmap.c: In function '_regmap_raw_write':
drivers/base/regmap/regmap.c:421:5: error: implicit declaration of function 'dev_err' [-Werror=implicit-function-declaration]
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Most of the current users have register 0 as a volatile register or don't
have a register 0 so it's not been apparent that it's not getting synced.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Remove unused module.h and/or replace with export.h
as required.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Provide a regcache_sync_region() operation which allows drivers to
write only part of the cache back to the hardware. This is intended
for use in cases like power domains or DSP memories where part of the
device register map may be reset without fully resetting the device.
Fully supporting these devices is likely to require additional work to
make specific regions of the register map cache only while they are in
reset, but this is enough for most devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In order to allow us to support partial sync operations add minimum and
maximum register arguments to the sync operation and update the rbtree
and lzo caches to use this new information. The LZO implementation is
obviously not good, we could exit the iteration earlier, but there may
be room for more wide reaching optimisation there.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Previously the cache would never be marked clean, meaning syncs would
never be suppressed which isn't the end of the world but could be
inefficient.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It's not used as all cache types have sync operations so it's just dead
code which never gets tested.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add a file called 'name' containing the name of the driver.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To enable writing to the regmap debugfs registers file users will
need to modify the source directly and #define REGMAP_ALLOW_WRITE_DEBUGFS.
The reason for this is that it is dangerous to expose this
functionality in general where clients could potentially be PMICs.
[A couple of minor style updates -- broonie]
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fall back to a register by register read to do so; most likely we'll be
cache only so the overhead will be low.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Generic infrastructure based on top of regmap may want to operate on
blocks of data and therefore find it useful to find the size of the
register values. Provide an accessor operation for this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
During regcache_init, if client has not passed the
default data of cached register then it is directly
read from the hw to initialize cache. This hw register
read happens before cache ops are initialized and hence
avoiding register read to check for the data available
on cache or not by enabling flag of cache_bypass.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently registers with a value of 0 are ignored when initializing the register
defaults from raw defaults. This worked in the past, because registers without a
explicit default were assumed to have a default value of 0. This was changed in
commit b03622a8 ("regmap: Ensure rbtree syncs registers set to zero properly").
As a result registers, which have a raw default value of 0 are now assumed to
have no default. This again can result in unnecessary writes when syncing the
cache. It will also result in unnecessary reads for e.g. the first update
operation. In the case where readback is not possible this will even let the
update operation fail, if the register has not been written to before.
So this patch removes the check. Instead it adds a check to ignore raw defaults
for registers which are volatile, since those registers are not cached.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
The bulk_write() supports the data transfer to multi
register which takes the data into cpu_endianness format
and does formatting of data to device format before
sending to device.
The transfer can be completed in single transfer or multiple
transfer based on data formatting.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Adding support for caching of data into the
non-volatile register from the call of reg_raw_write().
This will allow the larger block of data write into multiple
register without worrying whether register is cached or not
through reg_raw_write().
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The first parameter should be "number of elements" and the second parameter
should be "element size".
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This was a cut'n'paste from some older code.
Since we're about to add debugfs support don't do the obvious thing and
use bool, use u32 instead (which debugfs has been using since time
immemorial).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
regcache_set_val() returns false if cache[idx] != val.
Thus it actually is not unreachable.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Save error handling and unwinding code in drivers by providing managed
versions of the regmap init functions, simplifying usage.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Using .format_write means, we have a custom function to write to the
chip, but not to read back. Also, mark registers as "not precious" and
"not volatile" which is implicit because we cannot read them. Make those
functions use 'regmap_readable' to reuse the checks done there.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For the upcoming 2/6-format, we don't see debugfs output otherwise,
since the current division results in 0. I'd think 10/14 is broken
currently, too.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Most of the data exposed via debugfs is for or from the cache so reset
all the debugfs configuration to make sure everything is up to date with
the latest configuration, especially if we're changing cache type.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
On the basis that if we don't actually need to resync the cache then the
patches are probably also already applied.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
They have no current users which is fortunate as they don't take the lock
and therefore aren't safe to use externally. We'll need to add new
operations if direct cache access is needed.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Device manufacturers frequently provide register sequences, usually not
fully documented, to be run at startup in order to provide better defaults
for devices (for example, improving performance in the light of silicon
evaluation). Support such updates by allowing drivers to register update
sets with the core. These updates will be written to the device immediately
and will also be rewritten when the cache is synced.
The assumption is that the reason for resyncing the cache will always be
that the device has been powered off. If this turns out to not be the case
then a separate operation can be provided.
Currently the implementation only allows a single set of updates to be
specified for a device, this could be extended in future.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When we reinitialise the cache make sure that we reset the cache access
flags, ensuring that the reinitialised cache is in the default state
which is what callers would and do expect given the function name.
This is particularly likely to cause issues in systems where there was no
cache previously as those systems have cache bypass enabled, as for the
wm8994 driver where this was noticed.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some devices, especially those with high speed control interfaces, require
padding between the register and the data. Support this in the regmap API
by providing a pad_bits configuration parameter.
Only devices with integer byte counts are supported.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allows devices to discover their own interrupt without having to remember
it themselves.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Sometimes the register map information may change in ways that drivers can
discover at runtime. For example, new revisions of a device may add new
registers. Support runtime discovery by drivers by allowing the register
cache to be reinitialised with a new function regmap_reinit_cache() which
discards the existing cache and creates a new one.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently we only trace physical reads, there's no instrumentation if
the read is satisfied from cache.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some users of regmap_update_bits() would like to be able to tell their
users if they actually did an update so provide a variant which also
returns a flag indicating if an update took place. We could return a
tristate in the return value of regmap_update_bits() but this makes the
API more cumbersome to use and doesn't fit with the general zero for
success idiom we have.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
While the IRQ core doesn't currently support shared threaded interrupts
that's no reason for drivers not to do their bit and report IRQ_NONE when
they don't get an interrupt. This allows the core spurious/wedget interrupt
detection support to do its thing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The debugfs functions don't stub themselves out quite so well as might
be desirable so provide functions which do do this stubbing.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Show the register ranges we have in each rbtree node in debugfs, plus
some statistics on how big each node is and the total number of nodes.
It may also be worth collecting data on the ranges of dirty registers
to see if there's much mileage in trying to coalesce writes on sync.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If the new register value is identical to the original one then suppress
the write to the hardware in regmap_update_bits(), saving some I/O cost.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There should be no situation where it offers any advantage over rbtree
and there are no current users so remove the code for simplicity.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
One of the reasons for using a cache is to have a software shadow of a register
which is writable but not readable. This allows us to do a read-modify-write
operation on such a register.
Currently regcache checks whether a register is readable when performing a
cached read and returns an error if it is not. Drop this check, since it will
prevent us from using the cache for registers where read-back is not possible.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
regcache currently only properly works with val bit sizes of 8 or 16, since
it will, when calculating the cache word size, round down. This causes the
cache storage to be too small to hold the full register value. Fix this by
rounding up instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for 10 bits register, 14 bits value type register
formating. This is for example used by the Analog Devices AD5380.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For some register format types we do not provide a parse_val so we can not do a
hardware read. But a cached read is still possible, so try to read from the
cache first, before checking whether a hardware read is possible. Otherwise the
cache becomes pretty useless for these register types.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The reg_defaults field usually points to a static per driver array, which should
not be modified. Make requirement this explicit by making reg_defaults const.
To allow this the regcache_init code needs some minor changes. Previoulsy the
reg_config was not available in regcache_init and regmap->reg_defaults was used
to pass the default register set to regcache_init. Now that the reg_config is
available we can work on it directly.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Move the initialization regcache related fields of the regmap struct to
regcache_init. This allows us to keep regmap and regcache code better
separated.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Calling regcache_exit from regcache_lzo_init is first of all a layering
violation and secondly will cause double frees. regcache_exit will free buffers
allocated by the core, but the core will also free the same buffers when the
cacheops init callback returns an error. Thus we end up with a double free.
Fix this by not calling regcache_exit but only free those buffers which, have
been allocated in this function.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Calling regcache_exit from regcache_rbtree_init is first of all a layering
violation and secondly will cause double frees. regcache_exit will free buffers
allocated by the core, but the core will also free the same buffers when the
cacheops init callback returns an error. Thus we end up with a double free.
Fix this by not calling regcache_exit but only free those buffers which, have
been allocated in this function.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Make sure all allocated memory gets freed again in case initializing the cache
failed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Make sure reg_defaults_raw gets freed in case of an error.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The regmap_init documentation states that it will either return a pointer to a
valid regmap structure or a ERR_PTR in case of an error. Currently it returns a
NULL pointer in case no bus or no config was given. Since NULL is not a
ERR_PTR a caller might assume that it is a pointer to a valid regmap structure,
so return a ERR_PTR(-EINVAL) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If regcache initialization fails regmap_init will currently exit without
freeing work_buf.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit 10a08d9f ("regmap: Support some block operations on cached devices")
allowed raw read operations without throwing a warning when using caches if
all registers are volatile. This patch does the same for raw write operations.
This is for example useful when loading a firmware in a predefined volatile
region on a chip where we otherwise want registers to be cached.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We already have the same code for checking whether a register range is volatile
in two different places. Instead of duplicating it once more add a small helper
function for checking whether a register range is voltaile.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Users probably don't care about the specific compression algorithm and
we might want to use a different algorithm (snappy being the one I'm
thinking of right now) so update the public interface to have a more
generic name.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow drivers to optimise out the register cache sync if they didn't need
to do one. If the hardware is desynced from the register cache (by power
loss for example) then the driver should call regcache_mark_dirty() to
let the core know about this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Give regcache_lzo_block_count() a copy of the map so that when we decide
we want to make the LZO cache more controllable we can more easily do so.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
There seem to be lots of regmap-using devices with very similar interrupt
controllers with a small bank of interrupt registers and mask registers
with an interrupt per bit. This won't cover everything but it's a good
start.
Each chip supplies a base for the status registers, a base for the mask
registers, an optional base for writing acknowledgements (which may be the
same as the status registers) and an array of bits within each of these
register banks which indicate the interrupt.
There is an assumption that the bit for each interrupt will be the same
in each of the register bank.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Most of these files were implicitly getting EXPORT_SYMBOL via
device.h which was including module.h, but that path will be broken
soon.
[ with input from Stephen Rothwell <sfr@canb.auug.org.au> ]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
* 'for-linus' of git://opensource.wolfsonmicro.com/regmap: (62 commits)
mfd: Enable rbtree cache for wm831x devices
regmap: Support some block operations on cached devices
regmap: Allow caches for devices with no defaults
regmap: Ensure rbtree syncs registers set to zero properly
regmap: Allow rbtree to cache zero default values
regmap: Warn on raw I/O as well as bulk reads that bypass cache
regmap: Return a sensible error code if we fail to read the cache
regmap: Use bsearch() to search the register defaults
regmap: Fix doc comment
regmap: Optimize the lookup path to use binary search
regmap: Ensure we scream if we enable cache bypass/only at the same time
regmap: Implement regcache_cache_bypass helper function
regmap: Save/restore the bypass state upon syncing
regmap: Lock the sync path, ensure we use the lockless _regmap_write()
regmap: Fix apostrophe usage
regmap: Make _regmap_write() global
regmap: Fix lock used for regcache_cache_only()
regmap: Grab the lock in regcache_cache_only()
regmap: Modify map->cache_bypass directly
regmap: Fix regcache_sync generic implementation
...
Support raw reads if all the registers being read are volatile, the cache
will have no impact for tem.
Support bulk reads either directly (if all the registers are volatile) or
by falling back to iterating over single register reads otherwise.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We only really need the defaults in order to cut down the number of
registers we sync and to satisfy reads while the device is powered off
but not all devices are going to need to do that (always on devices like
PMICs being the prime example) so don't require those devices to supply
a default. Instead only try to fall back to hardware defaults if the
driver told us to.
Devices using LZO won't be able to instantiate with this, that will require
some updates in the LZO code to handle this case.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Simplify the check for registers set at their default value by avoiding
picking a default value in the case where we don't have one. Instead we
only compare the current value to the current value when we looked one
up. This fixes the case where we don't have a default stored but the value
was set to zero when that isn't the chip default.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Ensure that when we start up in cache only mode we can store defaults of
zero, otherwise if the hardware is unavailable we won't be able to read.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
As with the bulk reads we really should be able to make these play
nicely with the cache but warn for now.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
If a register isn't cached then let callers know that so they can fall
back or error handle appropriately.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Rather than open coding a binary search use the standard bsearch() using
the comparison function we're already using for sort() on insert. This
fixes a lockup I was observing due to iterating on min <= max rather
than min < max when we fail to look up.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Since there are more lookups than insertions in a typical
scenario, optimize the linear search into a binary search. For
this to work, we need to keep reg_defaults sorted upon
insertions, for now be lazy and use sort().
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensure we've got a function so users can enable/disable the
cache bypass option.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In preperation for the upcoming patches, modify map->cache_bypass
directly. The helper functions will grab an exclusive lock. Because
we'll have acquired the same lock we need to avoid a deadlock.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We want to use regmap_write() to actually write anything
to the HW.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Move the handling of the cached rbnode into regcache_rbtree_lookup. This allows
us to remove of some duplicated code sections in regcache_rbtree_read and
regcache_rbtree_write.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use regcache_{set,get}_val in regcache_rbtree_{set,get}_register instead of
re-implementing its functionality.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In the absence of a sync callback, do it manually. This of course
can't take advantange of the specific optimizations of each
cache type but it will do well enough in most cases.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch incorporates the regcache core code into regmap. All previous
patches have been no-ops essentially up to this point.
The bulk read operation is not supported by regcache at the moment. This
will be implemented incrementally.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Tested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for LZO compression when storing the register
cache.
For a typical device whose register map would normally occupy 25kB or 50kB
by using the LZO compression technique, one can get down to ~5-7kB. There
might be a performance penalty associated with each individual read/write
due to decompressing/compressing the underlying cache, however that should not
be noticeable. These memory benefits depend on whether the target architecture
can get rid of the memory occupied by the original register defaults cache
which is marked as __devinitconst. Nevertheless there will be some memory
gain even if the target architecture can't get rid of the original register
map, this should be around ~30-32kB instead of 50kB.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for the rbtree cache compression type.
Each rbnode manages a variable length block of registers. There can be no
two nodes with overlapping blocks. Each block has a base register and a
currently top register, all the other registers, if any, lie in between these
two and in ascending order.
The reasoning behind the construction of this rbtree is simple. In the
snd_soc_rbtree_cache_init() function, we iterate over the register defaults
provided by the regcache core. For each register value that is non-zero we
insert it in the rbtree. In order to determine in which rbnode we need
to add the register, we first look if there is another register already
added that is adjacent to the one we are about to add. If that is the case
we append it in that rbnode block, otherwise we create a new rbnode
with a single register in its block and add it to the tree.
There are various optimizations across the implementation to speed up lookups
by caching the most recently used rbnode.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Tested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is the simplest form of a cache available in regcache. Any
registers whose default value is 0 are ignored. If any of those
registers are modified in the future, they will be placed in the
cache on demand. The cache layout is essentially using the provided
register defaults by the regcache core directly and does not re-map
it to another representation.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch introduces caching support for regmap. The regcache API
has evolved essentially out of ASoC soc-cache so most of the actual
caching types (except LZO) have been tested in the past.
The purpose of regcache is to optimize in time and space the handling
of register caches. Time optimization is achieved by not having to go
over a slow bus like I2C to read the value of a register, instead it is
cached locally in memory and can be retrieved faster. Regarding space
optimization, some of the cache types are better at packing the caches,
for e.g. the rbtree and the LZO caches. By doing this the sacrifice in
time still wins over doing I2C transactions.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Tested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Make the debugfs stubs static inline to avoid future compilation issues due to
duplicated symbols when CONFIG_DEBUG_FS=n once internal.h is included by
multiple source files.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some buses like SPI have no standard notation of read or write operations.
The general scheme here is to set or clear specific bits in the register
address to indicate whether the operation is a read or write. We already
support having a read flag mask per bus, but as there is no standard
the bits which need to be set or cleared differ between devices and vendors,
thus we need a mechanism to specify them per device.
This patch adds two new entries to the regmap_config struct, read_flag_mask and
write_flag_mask. These will be or'ed onto the top byte when doing a read or
write operation. If both masks are empty the device will fallback to the
regmap_bus masks.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
No longer used as users link directly with the bus types so the core
module infrastructure does refcounting for us.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The conversion to per bus type registration functions means we don't need
to do module_get()s to hold the bus types in memory (their users will link
to them) so we removed all those calls. This left module_put() calls in
the cleanup paths which aren't needed and which cause unbalanced puts if
we ever try to unload anything.
Reported-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit b33f9cbd67 ("regmap: Specify a module license") added a
MODULES_LICENSE to this file without adding an include of module.h.
module.h should have been included anyway, since this file has
EXPORT_SYMBOLs as well. With the pending module.h split up, this would
probably have caused build problems.
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Let userspace know what the access map for the device is. This is helpful
for verifying that the access map is correctly configured and could also
be useful for programs that try to work with the data. File format is:
register: R W V P
where R, W, V and P are 'y' or 'n' showing readable, writable, volatile
and precious respectively.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We're going to be using these in quite a few places so factor out the
readable/writable/volatile/precious checks.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CONFIG_REGMAP_I2C/SPI are set to m when selected by a tristate config
option that's set to m. The regmap modules don't specify a license, so
fail to link to regmap_init at load time, since that is EXPORT_SYMBOL_GPL.
Fix this by specifying a license for the regmap modules.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
x86_64 size_t is not an int but the printf format specifier for size_t
should be an int.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Copy over the read parts of the ASoC debugfs implementation into regmap,
allowing users to see what the register values the device has are at
runtime. The implementation, especially the support for seeking, is
mostly due to Dimitris Papastamos' work in ASoC.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is mainly intended to be used by devices which can dynamically
block register writes at runtime, for other devices there is usually
limited value.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Trace single register reads and writes, plus start/stop tracepoints for
the actual I/O to see where we're spending time. This makes it easy to
have always on logging without overwhelming the logs and also lets us take
advantage of all the context and time information that the trace subsystem
collects for us.
We don't currently trace register values for bulk operations as this would
add complexity and overhead parsing the cooked data that's being worked
with.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When doing a single register write we use work_buf for both the register
and the value with the buffer formatted for sending directly to the device
so we can just do a write() directly. This saves allocating a temporary
buffer if we can't do gather writes and is likely to be faster than doing
a gather write.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is currently unused but we need to know which registers exist and
their properties in order to implement diagnostics like register map
dumps and the cache features.
We use callbacks partly because properties can vary at runtime (eg, through
access locks on registers) and partly because big switch statements are a
good compromise between readable code and small data size for providing
information on big register maps.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We should be reading the number of bytes we were asked for, not the size
of a single register.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
There are many places in the tree where we implement register access for
devices on non-memory mapped buses, especially I2C and SPI. Since hardware
designers seem to have settled on a relatively consistent set of register
interfaces this can be effectively factored out into shared code. There
are a standard set of formats for marshalling data for exchange with the
device, with the actual I/O mechanisms generally being simple byte
streams.
We create an abstraction for marshaling data into formats which can be
sent on the control interfaces, and create a standard method for
plugging in actual transport underneath that.
This is mostly a refactoring and renaming of the bottom level of the
existing code for sharing register I/O which we have in ASoC. A
subsequent patch in this series converts ASoC to use this. The main
difference in interface is that reads return values by writing to a
location provided by a pointer rather than in the return value, ensuring
we can use the full range of the type for register data. We also use
unsigned types rather than ints for the same reason.
As some of the devices can have very large register maps the existing
ASoC code also contains infrastructure for managing register caches.
This cache work will be moved over in a future stage to allow for
separate review, the current patch only deals with the physical I/O.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Mark Brown