Now that we can handle the generic pinctrl bindings, convert our DT to it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The mini-x has the otg controller connected to one of the 2 usb-A
receptacles it has on the front, so enable the otg controller in host-only
mode.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The FSF address triggers a warning on checkpatch, saying that the FSF
license is already present in the Linux source code, and that it has
already changed in the past.
Remove it from our DT, as suggested.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Currently none of the target boards nor the driver supports
IR TX. However this pin is used in a few instances as a GPIO.
Split the pin ctrl descriptions so that only the IR RX is
configured to be used.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add UART aliases and stdout-path property for all the Allwinner boards so that
we won't have to rely on the bootargs' console= value, while working with
legacy bootloaders.
While we're at it, also remove the mentions of earlyprintk in the bootargs,
that will remove our default bootargs entirely, and allow the kernel to boot on
a system even if DEBUG_LL is configured for another system.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The pinctrl nodes require some extra opaque arguments for the pull up and drive
strength values.
Introduce a new header file and convert the device trees to replace these
opaque numbers by defines.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Replace the various raw GPIO flags by their definition in the common
dt-bindings header.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Carlo Caione <carlo@caione.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested on a cubieboard and the mini-x.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
At a node for the axp209, and where necessary the i2c controller to the dts
for various boards. Note the axp209 regulators are omitted as we don't have
any use for them yet, and on some boards were not sure how exactly they are
wired up.
Adding support for just the axp209 without the regulators is still useful, as
it will give us power-button and poweroff support.
Signed-off-by: Carlo Caione <carlo@caione.org>
[hdegoede@redhat.com: Drop the regulator bits for now]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested on a subset of these boards, for the others boards the settings match
the ones of the tested boards according to the original firmware fex files.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add nodes for the usb-phy and ehci- and ohci-usb-host controllers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The chosen nodes are nowadays pretty useless, since they will be overriden by
the bootloader anyway.
We can thus safely remove them.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
There was a typo in the base address used for the soc node in the A10
device tree. Fix it with the proper base address.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Commit b00adbe0 ("ARM: sunxi: Rename uart nodes to serial") changed the
node names in the DTSI, changes that were not accordingly made to the
Mini X-Plus device tree. This breakage slipped through because it was
not properly declared in the Makefile.
Fix both issues.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This board comes with an Allwinner A10, two external USB ports, a SD
Card reader, 1GB of RAM, the usual video connectors and an onboard wifi
chip.
Of course, the support is quite minimal for now...
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard