Separate the definitions for the emac and the gmac in different files and
include them in the final board dts that uses them.
Solves:
Warning (unit_address_vs_reg): Node /ahb/apb/ethernet@f0028000 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /ahb/apb/ethernet@f802c000 has a unit name, but no reg property
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
On at91sam9x5ek/at91sam9m10g45ek/sama5d3xek boards, we use the parallel
connection for ov2640. So we must set the hsync/vsync property (1 means
active high).
Otherwise, the connection would be seen as BT.656 or BT.1120.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
DT changes continue to be the bulk of our merge window contents.
We continue to have a large set of changes across the board as new platforms
and drivers are added.
Some of the new platforms are:
- Alphascale ASM9260
- Marvell Armada 388
- CSR Atlas7
- TI Davinci DM816x
- Hisilicon HiP01
- ST STiH418
There have also been some sweeping changes, including relicensing of DTS
contents from GPL to GPLv2+/X11 so that the same files can be reused in
other non-GPL projects more easily. There's also been changes to the
DT Makefile to make it a little less conflict-ridden and churny down
the road.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XEw1
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"DT changes continue to be the bulk of our merge window contents.
We continue to have a large set of changes across the board as new
platforms and drivers are added.
Some of the new platforms are:
- Alphascale ASM9260
- Marvell Armada 388
- CSR Atlas7
- TI Davinci DM816x
- Hisilicon HiP01
- ST STiH418
There have also been some sweeping changes, including relicensing of
DTS contents from GPL to GPLv2+/X11 so that the same files can be
reused in other non-GPL projects more easily. There's also been
changes to the DT Makefile to make it a little less conflict-ridden
and churny down the road"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (330 commits)
ARM: dts: Add PPMU node for exynos4412-trats2
ARM: dts: Add PPMU node for exynos3250-monk and exynos3250-rinato
ARM: dts: Add PPMU dt node for exynos4 and exynos4210
ARM: dts: Add PPMU dt node for exynos3250
ARM: dts: add mipi dsi device node for exynos4415
ARM: dts: add fimd device node for exynos4415
ARM: dts: Add syscon phandle to the video-phy node for Exynos4
ARM: dts: Add sound nodes for exynos4412-trats2
ARM: dts: Fix CLK_MOUT_CAMn parent clocks assignment for exynos4412-trats2
ARM: dts: Fix CLK_UART_ISP_SCLK clock assignment in exynos4x12.dtsi
ARM: dts: Add max77693 charger node for exynos4412-trats2
ARM: dts: Switch max77686 regulators to GPIO control for exynos4412-trats2
ARM: dts: Add suspend configuration for max77686 regulators for exynos4412-trats2
ARM: dts: Add Maxim 77693 fuel gauge node for exynos4412-trats2
ARM: dts: am57xx-beagle-x15: Fix USB2 mode
ARM: dts: am57xx-beagle-x15: Add extcon nodes for USB
ARM: dts: dra72-evm: Add extcon nodes for USB
ARM: dts: dra7-evm: Add extcon nodes for USB
ARM: dts: rockchip: move the hdmi ddc-i2c-bus property to the actual boards
ARM: dts: rockchip: enable vops and hdmi output on rk3288-firefly and -evb
...
- several fixes and adjustments following the last cleanup batch
- removal of some unused Kconfig options
- slight PM and pm_idle rework to ease future rework
- removal of unneeded mach/system_rev.h
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJUxjj9AAoJEAf03oE53VmQGEAH/3nLneCOQeyuq60adx+Lxcdn
Q9sMMzrw4B6bQnJee7+PQD3/QU7fmF8qNKlMKYAlILFHGNQplASi4uAfRTykUA0j
RQHpS9n20ODVfX+yePJ/o8h2r1BkT2wUIDXxaZCj2RoPmEz1aiFDNa2pPsUfprRd
gpbh+ZU43LRowYwH9UHPV55PQ0ZwMq3ry2DOYY5Al1+bKQ8TFvAdDMUu3rGZU7A4
dMYiQCQ6Fv0EI1NY0IHSf/u/jujlPE2H0TSR38w8lYfIPzBx2tHkLSupuxKh7R1N
QYibgZXWR0PqHOXMpOHYBqJFj5c3f/aOZ/dO4RJha+S7YHNQnIFzLsm122njgKQ=
=KgUm
-----END PGP SIGNATURE-----
Merge tag 'at91-cleanup3' into at91-3.20-soc
Using the wm8904 device tree compatible string.
Signed-off-by: Alexander Morozov <linux@meltdown.ru>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
According to v4l2 dt document, we add:
a camera host: ISI port.
a i2c camera sensor: ov2640 port.
to sama5d3xmb.dtsi.
The ov2640 node defines the pinctrls, clocks and refer to isi port.
The ISI node also has a reference to the ov2640 port.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
For sama5d3xmb board, the pins: pinctrl_isi_pck_as_mck is pck1, and
used to provide MCK for camera sensor.
We change its name to: pinctrl_pck1_as_isi_mck.
As we want camera sensor instead of ISI to configure the pck1 (ISI_MCK) pin.
So we remove this pinctrl from ISI DT node. It will be added in sensor's
DT node.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
For sama5d3xmb board, the pins: pinctrl_isi_{power,reset} is used to
power-down or reset camera sensor.
So we should let camera sensor instead of ISI to configure the pins.
This patch will change pinctrl name from pinctrl_isi_{power,reset} to
pinctrl_sensor_{power,reset}. And remove these two pinctrl from ISI's
DT node. We will add these two pinctrl to sensor's DT node.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The mck is decided by the board design, move it to mb related
dtsi file.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
As the ISI has 12 data lines, however we only use 8 data lines with
sensor module. So, split the data line into two groups which make
it can be choosed depends on the hardware design.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The MICBIAS is a supply, should route to MIC while not IN1L.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
We set the DMA configuration on USARTs in the SoC DT in (ARM: at91: sama5d3:
add usart dma configurations). As the audio must work with DMA channels, we
reserve some dma channels for audio, or else audio won't work.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
[nicolas.ferre@atmel.com: move to the sama5d3xmb.dtsi to cover all board variants]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
As the sama5d3xek board has switch to CCF, so add clock for wm8904
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Reviwed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
According to hardware design the clock for SSC device is from rk pin.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
If without the MICBIAS routing, the record don't work.
Add the missing MICBIAS routing to let record from mic working.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
As the sama5d3 dtsi file in go into mainline before sound driver,
and, the sound compatible string is changed when go into mainline.
Add this patch to correct the sound compatible string.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Make the sound device in disabled status by default
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Fix phy0 address to match the reg property defined in phy0 node.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch describe the phy used on atmel sama5d3 mother board:
- phy address
- phy interrupt pin
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
to prepare the switch to the macro.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add device tree files for the SAMA5D3 family (SAMA5D31, SAMA5D33, SAMA5D34 and
SAMA5D35).
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Alexandre Belloni