Fine-tune read register for mt7663/mt7921.
For mediatek chip spcific wmt protocol, we add more delay to send EP0
In-Token.
Signed-off-by: Mark Chen <Mark-YW.Chen@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
QCA_IBS_DISABLED flag will be set after memorydump started from
controller.Currently qca_suspend() is waiting for SSR to complete
based on flag QCA_IBS_DISABLED.Added to check for QCA_SSR_TRIGGERED
flag too.
Fixes: 2be43abac5 ("Bluetooth: hci_qca: Wait for timeout during suspend")
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
By this change, it will enable WBS supported on the specific Realtek BT
devices, such as RTL8822C and RTL8852A.
In the future, it's able to maintain what the Realtek devices support WBS
here.
Tested-by: Hilda Wu <hildawu@realtek.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Realtek Bluetooth controllers can do both LE scan and BR/EDR inquiry
at once, need to set HCI_QUIRK_SIMULTANEOUS_DISCOVERY quirk.
Signed-off-by: Claire Chang <tientzu@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Fixes both the "splice/sendfile to a tty" and "splice/sendfile from a
tty" regression from 5.10.
* 'tty-splice' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux:
tty: teach the n_tty ICANON case about the new "cookie continuations" too
tty: teach n_tty line discipline about the new "cookie continuations"
tty: clean up legacy leftovers from n_tty line discipline
tty: implement read_iter
tty: convert tty_ldisc_ops 'read()' function to take a kernel pointer
tty: implement write_iter
The tty line discipline .read() function was passed the final user
pointer destination as an argument, which doesn't match the 'write()'
function, and makes it very inconvenient to do a splice method for
ttys.
This is a conversion to use a kernel buffer instead.
NOTE! It does this by passing the tty line discipline ->read() function
an additional "cookie" to fill in, and an offset into the cookie data.
The line discipline can fill in the cookie data with its own private
information, and then the reader will repeat the read until either the
cookie is cleared or it runs out of data.
The only real user of this is N_HDLC, which can use this to handle big
packets, even if the kernel buffer is smaller than the whole packet.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During SSR after memory dump collection,BT controller will be powered off,
powered on and then FW will be downloaded.During suspend if BT controller
is powered off due to SSR then we should wait until SSR is completed and
then suspend.
Fixes: 2be43abac5 ("Bluetooth: hci_qca: Wait for timeout during suspend")
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When __le32_to_cpu() fails, qca_memdump should be freed
just like when vmalloc() fails.
Fixes: d841502c79 ("Bluetooth: hci_qca: Collect controller memory dump during SSR")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
RTL8723DS could be handled by btrtl-driver, so add ability to bind it
using device tree.
Signed-off-by: John-Eric Kamps <johnny86@gmx.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
btrtl_dev->ic_info is only available from the controller on cold boot
(the lmp subversion matches the device model and this is used to look up
the ic_info). On warm boots (firmware already loaded),
btrtl_dev->ic_info is null.
Fixes: 05672a2c14 (Bluetooth: btrtl: Enable central-peripheral role)
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Enable the central-peripheral role on RTL8822CE. This enables creating
connections while there is an existing connection in the slave role.
This change can be confirmed in userspace via `bluetoothctl show` which
will now show "Roles: central-peripheral".
Reviewed-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This reverts commit a63f23c9d139377833a139b179793fea79ee198f.
get_unaligned_{le16|le32|le64}(p) is meant to replace code of the form
le16_to_cpu(get_unaligned((__le16 *)p)). There is no need to explicitly
do leXX_to_cpu() if get_unaligned_leXX() is used.
https://lwn.net/Articles/277779/
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This enables bcm driver to properly handle ISO packets.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Realtek RTL8822CE Bluetooth controller support Microsoft vendor
extension and it uses 0xFCF0 for VsMsftOpCode.
The following test step was performed.
- Boot the test device with RTL8822CE and verify the INFO print in
dmesg.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Archie Pusaka <apusaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Intel JeffersonPeak, HarrisonPeak and CyclonePeak Bluetooth
controllers support the Microsoft vendor extension and they are using
0xFC1E for VsMsftOpCode.
< HCI Command: Vendor (0x3f|0x001e) plen 1
00
> HCI Event: Command Complete (0x0e) plen 15
Vendor (0x3f|0x001e) ncmd 1
Status: Success (0x00)
00 3f 00 00 00 00 00 00 00 01 50
The following test step was performed.
- Boot the test devices with HarrisonPeak and verify INFO print in
dmesg.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Archie Pusaka <apusaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The following Qualcomm WCN399x Bluetooth controllers support the
Microsoft vendor extension and they are using 0xFD70 for VsMsftOpCode.
-WCN3990
-WCN3991
-WCN3998
< HCI Command: ogf 0x3f, ocf 0x0170, plen 1
00
> HCI Event: 0x0e plen 18
01 70 FD 00 00 1F 00 00 00 00 00 00 00 04 4D 53 46 54
The following test step was performed.
- Boot the device with WCN3991 and verify INFO print in dmesg.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Archie Pusaka <apusaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
we should send hci reset command before bt turn off, which can reset bt
firmware status.
Signed-off-by: Tim Jiang <tjiang@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In hci_uart_write_work, there is a loop/goto checking the value of
HCI_UART_TX_WAKEUP. If HCI_UART_TX_WAKEUP is set again, it keeps trying
hci_uart_dequeue; otherwise, it clears HCI_UART_SENDING and returns.
In hci_uart_tx_wakeup, if HCI_UART_SENDING is already set, it sets
HCI_UART_TX_WAKEUP, skips schedule_work and assumes the running/pending
hci_uart_write_work worker will do hci_uart_dequeue properly.
However, if the HCI_UART_SENDING check in hci_uart_tx_wakeup is done after
the loop breaks, but before HCI_UART_SENDING is cleared in
hci_uart_write_work, the schedule_work is skipped incorrectly.
Fix this race by changing the order of HCI_UART_SENDING and
HCI_UART_TX_WAKEUP modification.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Fixes: 82f5169bf3 ("Bluetooth: hci_uart: add serdev driver support library")
Signed-off-by: Claire Chang <tientzu@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add support to read FW build version from debugfs node.
This info can be read from
/sys/kernel/debug/bluetooth/hci0/firmware_info
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When alt mode 6 is not available, fallback to the kernel <= 5.7 behavior
of always using alt mode 1.
Prior to kernel 5.8, btusb would always use alt mode 1 for WBS (Wide
Band Speech aka mSBC aka transparent SCO). In commit baac6276c0
("Bluetooth: btusb: handle mSBC audio over USB Endpoints") this
was changed to use alt mode 6, which is the recommended mode in the
Bluetooth spec (Specifications of the Bluetooth System, v5.0, Vol 4.B
§2.2.1). However, many if not most BT USB adapters do not support alt
mode 6. In fact, I have been unable to find any which do.
In kernel 5.8, this was changed to use alt mode 6, and if not available,
use alt mode 0. But mode 0 has a zero byte max packet length and can
not possibly work. It is just there as a zero-bandwidth dummy mode to
work around a USB flaw that would prevent device enumeration if
insufficient bandwidth were available for the lowest isoc mode
supported.
In effect, WBS was broken for all USB-BT adapters that do not support
alt 6, which appears to nearly all of them.
Then in commit 461f95f04f ("Bluetooth: btusb: USB alternate setting 1 for
WBS") the 5.7 behavior was restored, but only for Realtek adapters.
I've tested a Broadcom BRCM20702A and CSR 8510 adapter, both work with
the 5.7 behavior and do not with the 5.8.
So get rid of the Realtek specific flag and use the 5.7 behavior for all
adapters as a fallback when alt 6 is not available. This was the
kernel's behavior prior to 5.8 and I can find no adapters for which it
is not correct. And even if there is an adapter for which this does not
work, the current behavior would be to fall back to alt 0, which can not
possibly work either, and so is no better.
Signed-off-by: Trent Piepho <tpiepho@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some resource should be released in the error handling path of the probe
function, as already done in the remove function.
The remove function was fixed in commit 5052de8def ("soc: qcom: smd:
Transition client drivers from smd to rpmsg")
Fixes: 1511cc750c ("Bluetooth: Introduce Qualcomm WCNSS SMD based HCI driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
With the recent btusb change to detect and deal with more fake CSR
controllers, I decided to see if fake CSR controllers with Barrot
8041a02 chips would now work.
After much experimentation I came to the conclusion that it works, if I
have autosuspend enabled initially and then disable it after the device
has suspended at least once. Yes this is very weird, but I've tried many
things, like manually clearing the remote-wakeup feature. Doing a
runtime-resume + runtime suspend is the only way to get the receiver
to actually report received data (and/or pairing info) through its
bulk rx endpoint.
But the funkyness of the bulk-endpoint does not stop there, I mainly
found out about this problem, because with autosuspend enabled
(which usually ensures the suspend at least once condition is met),
the receiver stops reporting received data through its bulk rx endpoint
as soon as autosuspend kicks in. So I initially just disabled
autosuspend, but then the receiver does not work at all.
This was with a fake CSR receiver with a Barrot 8041a02 chip with a
bcdDevice value of 0x8891, a lmp_subver of 0x1012, a hci_rev of 0x0810
and a hci_ver of BLUETOOTH_VER_4_0.
Summarizing this specific fake CSR receiver has the following 2 issues:
1. The bulk rx endpoint will never report any data unless
the device was suspended at least once.
2. They will not wakeup when autosuspended and receiving data on their
bulk rx endpoint from e.g. a keyboard or mouse (IOW remote-wakeup support
is broken for the bulk endpoint).
Add a workaround for 1. which enables runtime-suspend, force-suspends
the hci and then wakes-it up by disabling runtime-suspend again.
Add a workaround for 2. which clears the hci's can_wake flag, this way
the hci will still be autosuspended when it is not open.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Commit cde1a8a992 ("Bluetooth: btusb: Fix and detect most of the
Chinese Bluetooth controllers") made the detection of fake controllers
more generic fixing it for much of the newer fakes / clones.
But this does not work for a fake CSR controller with a bcdDevice
value of 0x0134, which was correctly identified as fake before
this change.
Add an extra check for this special case, checking for a combination
of a bcdDevice value of 0x0134, together with a lmp_subver of 0x0c5c
and a hci_ver of BLUETOOTH_VER_2_0.
The chip inside this fake dongle is marked as with "clockwise cw6629d".
Fixes: cde1a8a992 ("Bluetooth: btusb: Fix and detect most of the Chinese Bluetooth controllers")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
we define many nvm files for wcn6855 btsoc and host driver
should find the correct nvm file based on board ID and then
download it.
Signed-off-by: Tim Jiang <tjiang@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Define a helper function to download firmware for new generation Intel
controllers
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Define a new function to construct firmware/ddc filename for new
generation Intel controllers
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Define a new *setup* function for new generation Intel controllers
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Amit K Bag <amit.k.bag@intel.com>
Signed-off-by: Raghuram Hegde <raghuram.hegde@intel.com>
Reviewed-by: Sathish Narasimman <Sathish.Narasimman@intel.com>
Reviewed-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Reviewed-by: Srivatsa Ravishankar <ravishankar.srivatsa@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
do __le32_to_cpu to tlv data fields to make sure driver runs
correctly when running on big endian system.
Signed-off-by: Kiran K <kiran.k@intel.com>
Reviewed-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Reviewed-by: Srivatsa Ravishankar <ravishankar.srivatsa@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
mtk_setup_firmware() misses to call release_firmware() in an error
path. Jump to free_fw to fix it.
Fixes: 737cd06072 ("Bluetooth: btmtksdio: fix up firmware download sequence")
Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
btusb_mtk_setup_firmware() misses to call release_firmware() in an error
path. Jump to err_release_fw to fix it.
Fixes: f645125711 ("Bluetooth: btusb: fix up firmware download sequence")
Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This change will allow to use different NVM file based
on WCN3991 BT SoC ID.Need to use different NVM file based on
fab location for WCN3991 BT SoC.
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add OBDA0623 ACPI HID to the acpi_device_id table. This HID is used
for the RTL8723BS Bluetooth part on the Acer Switch 10E SW3-016.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1665610
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There have been multiple revisions of the patch fix the h5->rx_skb
leak. Accidentally the first revision (which is buggy) and v5 have
both been merged:
v1 commit 70f259a3f4 ("Bluetooth: hci_h5: close serdev device and free
hu in h5_close");
v5 commit 855af2d74c ("Bluetooth: hci_h5: fix memory leak in h5_close")
The correct v5 makes changes slightly higher up in the h5_close()
function, which allowed both versions to get merged without conflict.
The changes from v1 unconditionally frees the h5 data struct, this
is wrong because in the serdev enumeration case the memory is
allocated in h5_serdev_probe() like this:
h5 = devm_kzalloc(dev, sizeof(*h5), GFP_KERNEL);
So its lifetime is tied to the lifetime of the driver being bound
to the serdev and it is automatically freed when the driver gets
unbound. In the serdev case the same h5 struct is re-used over
h5_close() and h5_open() calls and thus MUST not be free-ed in
h5_close().
The serdev_device_close() added to h5_close() is incorrect in the
same way, serdev_device_close() is called on driver unbound too and
also MUST no be called from h5_close().
This reverts the changes made by merging v1 of the patch, so that
just the changes of the correct v5 remain.
Cc: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently qca_suspend() is relied on IBS mechanism. During
FW download and memory dump collections, IBS will be disabled.
In those cases, driver will allow suspend and still uses the
serdev port, which results to errors. Now added a wait timeout
if suspend is triggered during FW download and memory collections.
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently the check for a failed bt_skb_alloc allocation is incorrectly
checking using IS_ERR and this can lead to a null pointer dereference. Fix
this by checking for a null pointer return using the !skb idiom.
Addresses-Coverity: ("Dereference null return")
Fixes: 1996d9cad6 ("Bluetooth: btrtl: Ask 8821C to drop old firmware")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When using the wl1271 Bluetooth function of am335x, it is found that the
Bluetooth module cannot respond in time after Bluetooth is enabled, and
a small delay is needed to work normally, so whether to add a small
mdelay.
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Replace symbolic permissions with octal values. Use usleep_range
for small msec values due to the fact that msleep() less than
20ms may have unexpected behavior/sleep longer.
- https://lkml.org/lkml/2016/8/2/1945
- Documentation/timers/timers-howto.rst
Signed-off-by: Nigel Christian <nigel.l.christian@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently driver only retries to download FW if FW downloading
is failed. Sometimes observed command timeout for version request
command, if this happen on some platforms during boot time, then
a reboot is needed to turn ON BT. Instead to avoid a reboot, now
extended retry logic for version request command too.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When h5_close() is called, h5 is directly freed when !hu->serdev.
However, h5->rx_skb is not freed, which causes a memory leak.
Freeing h5->rx_skb and setting it to NULL, fixes this memory leak.
Fixes: ce945552fd ("Bluetooth: hci_h5: Add support for serdev enumerated devices")
Reported-by: syzbot+6ce141c55b2f7aafd1c4@syzkaller.appspotmail.com
Tested-by: syzbot+6ce141c55b2f7aafd1c4@syzkaller.appspotmail.com
Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some platforms keep USB power even when they are powered off and in S5,
this makes Realtek 8821C keep its firmware even after a cold boot, and
make 8821C never load new firmware.
So use vendor specific HCI command to ask 8821C drop its firmware after
system shutdown.
Newer firmware doesn't have this issue so we only use this trick for old
8821C firmware version.
Suggested-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Enhance the ic_id_table that it's able to maintain regularly.
To judge which chip should be initialized by LMP subversion, HCI revision,
HCI version and HCI bus which were given in the ic_id_table.
Also, refine the incorrect LMP subversion of ROM for RTL8723D and
RTL8723A.
Suggested-by: Alex Lu <alex_lu@realsil.com.cn>
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
WCN3991 supports connectable advertisements so we need to add the valid
le states quirk so the 'central-peripheral' role is exposed in
userspace.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add redirect_neigh() BPF packet redirect helper, allowing to limit stack
traversal in common container configs and improving TCP back-pressure.
Daniel reports ~10Gbps => ~15Gbps single stream TCP performance gain.
Expand netlink policy support and improve policy export to user space.
(Ge)netlink core performs request validation according to declared
policies. Expand the expressiveness of those policies (min/max length
and bitmasks). Allow dumping policies for particular commands.
This is used for feature discovery by user space (instead of kernel
version parsing or trial and error).
Support IGMPv3/MLDv2 multicast listener discovery protocols in bridge.
Allow more than 255 IPv4 multicast interfaces.
Add support for Type of Service (ToS) reflection in SYN/SYN-ACK
packets of TCPv6.
In Multi-patch TCP (MPTCP) support concurrent transmission of data
on multiple subflows in a load balancing scenario. Enhance advertising
addresses via the RM_ADDR/ADD_ADDR options.
Support SMC-Dv2 version of SMC, which enables multi-subnet deployments.
Allow more calls to same peer in RxRPC.
Support two new Controller Area Network (CAN) protocols -
CAN-FD and ISO 15765-2:2016.
Add xfrm/IPsec compat layer, solving the 32bit user space on 64bit
kernel problem.
Add TC actions for implementing MPLS L2 VPNs.
Improve nexthop code - e.g. handle various corner cases when nexthop
objects are removed from groups better, skip unnecessary notifications
and make it easier to offload nexthops into HW by converting
to a blocking notifier.
Support adding and consuming TCP header options by BPF programs,
opening the doors for easy experimental and deployment-specific
TCP option use.
Reorganize TCP congestion control (CC) initialization to simplify life
of TCP CC implemented in BPF.
Add support for shipping BPF programs with the kernel and loading them
early on boot via the User Mode Driver mechanism, hence reusing all the
user space infra we have.
Support sleepable BPF programs, initially targeting LSM and tracing.
Add bpf_d_path() helper for returning full path for given 'struct path'.
Make bpf_tail_call compatible with bpf-to-bpf calls.
Allow BPF programs to call map_update_elem on sockmaps.
Add BPF Type Format (BTF) support for type and enum discovery, as
well as support for using BTF within the kernel itself (current use
is for pretty printing structures).
Support listing and getting information about bpf_links via the bpf
syscall.
Enhance kernel interfaces around NIC firmware update. Allow specifying
overwrite mask to control if settings etc. are reset during update;
report expected max time operation may take to users; support firmware
activation without machine reboot incl. limits of how much impact
reset may have (e.g. dropping link or not).
Extend ethtool configuration interface to report IEEE-standard
counters, to limit the need for per-vendor logic in user space.
Adopt or extend devlink use for debug, monitoring, fw update
in many drivers (dsa loop, ice, ionic, sja1105, qed, mlxsw,
mv88e6xxx, dpaa2-eth).
In mlxsw expose critical and emergency SFP module temperature alarms.
Refactor port buffer handling to make the defaults more suitable and
support setting these values explicitly via the DCBNL interface.
Add XDP support for Intel's igb driver.
Support offloading TC flower classification and filtering rules to
mscc_ocelot switches.
Add PTP support for Marvell Octeontx2 and PP2.2 hardware, as well as
fixed interval period pulse generator and one-step timestamping in
dpaa-eth.
Add support for various auth offloads in WiFi APs, e.g. SAE (WPA3)
offload.
Add Lynx PHY/PCS MDIO module, and convert various drivers which have
this HW to use it. Convert mvpp2 to split PCS.
Support Marvell Prestera 98DX3255 24-port switch ASICs, as well as
7-port Mediatek MT7531 IP.
Add initial support for QCA6390 and IPQ6018 in ath11k WiFi driver,
and wcn3680 support in wcn36xx.
Improve performance for packets which don't require much offloads
on recent Mellanox NICs by 20% by making multiple packets share
a descriptor entry.
Move chelsio inline crypto drivers (for TLS and IPsec) from the crypto
subtree to drivers/net. Move MDIO drivers out of the phy directory.
Clean up a lot of W=1 warnings, reportedly the actively developed
subsections of networking drivers should now build W=1 warning free.
Make sure drivers don't use in_interrupt() to dynamically adapt their
code. Convert tasklets to use new tasklet_setup API (sadly this
conversion is not yet complete).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE6jPA+I1ugmIBA4hXMUZtbf5SIrsFAl+ItRwACgkQMUZtbf5S
IrtTMg//UxpdR/MirT1DatBU0K/UGAZY82hV7F/UC8tPgjfHZeHvWlDFxfi3YP81
PtPKbhRZ7DhwBXefUp6nY3UdvjftrJK2lJm8prJUPSsZRye8Wlcb7y65q7/P2y2U
Efucyopg6RUrmrM0DUsIGYGJgylQLHnMYUl/keCsD4t5Bp4ksyi9R2t5eitGoWzh
r3QGdbSa0AuWx4iu0i+tqp6Tj0ekMBMXLVb35dtU1t0joj2KTNEnSgABN3prOa8E
iWYf2erOau68Ogp3yU3miCy0ZU4p/7qGHTtzbcp677692P/ekak6+zmfHLT9/Pjy
2Stq2z6GoKuVxdktr91D9pA3jxG4LxSJmr0TImcGnXbvkMP3Ez3g9RrpV5fn8j6F
mZCH8TKZAoD5aJrAJAMkhZmLYE1pvDa7KolSk8WogXrbCnTEb5Nv8FHTS1Qnk3yl
wSKXuvutFVNLMEHCnWQLtODbTST9DI/aOi6EctPpuOA/ZyL1v3pl+gfp37S+LUTe
owMnT/7TdvKaTD0+gIyU53M6rAWTtr5YyRQorX9awIu/4Ha0F0gYD7BJZQUGtegp
HzKt59NiSrFdbSH7UdyemdBF4LuCgIhS7rgfeoUXMXmuPHq7eHXyHZt5dzPPa/xP
81P0MAvdpFVwg8ij2yp2sHS7sISIRKq17fd1tIewUabxQbjXqPc=
=bc1U
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
- Add redirect_neigh() BPF packet redirect helper, allowing to limit
stack traversal in common container configs and improving TCP
back-pressure.
Daniel reports ~10Gbps => ~15Gbps single stream TCP performance gain.
- Expand netlink policy support and improve policy export to user
space. (Ge)netlink core performs request validation according to
declared policies. Expand the expressiveness of those policies
(min/max length and bitmasks). Allow dumping policies for particular
commands. This is used for feature discovery by user space (instead
of kernel version parsing or trial and error).
- Support IGMPv3/MLDv2 multicast listener discovery protocols in
bridge.
- Allow more than 255 IPv4 multicast interfaces.
- Add support for Type of Service (ToS) reflection in SYN/SYN-ACK
packets of TCPv6.
- In Multi-patch TCP (MPTCP) support concurrent transmission of data on
multiple subflows in a load balancing scenario. Enhance advertising
addresses via the RM_ADDR/ADD_ADDR options.
- Support SMC-Dv2 version of SMC, which enables multi-subnet
deployments.
- Allow more calls to same peer in RxRPC.
- Support two new Controller Area Network (CAN) protocols - CAN-FD and
ISO 15765-2:2016.
- Add xfrm/IPsec compat layer, solving the 32bit user space on 64bit
kernel problem.
- Add TC actions for implementing MPLS L2 VPNs.
- Improve nexthop code - e.g. handle various corner cases when nexthop
objects are removed from groups better, skip unnecessary
notifications and make it easier to offload nexthops into HW by
converting to a blocking notifier.
- Support adding and consuming TCP header options by BPF programs,
opening the doors for easy experimental and deployment-specific TCP
option use.
- Reorganize TCP congestion control (CC) initialization to simplify
life of TCP CC implemented in BPF.
- Add support for shipping BPF programs with the kernel and loading
them early on boot via the User Mode Driver mechanism, hence reusing
all the user space infra we have.
- Support sleepable BPF programs, initially targeting LSM and tracing.
- Add bpf_d_path() helper for returning full path for given 'struct
path'.
- Make bpf_tail_call compatible with bpf-to-bpf calls.
- Allow BPF programs to call map_update_elem on sockmaps.
- Add BPF Type Format (BTF) support for type and enum discovery, as
well as support for using BTF within the kernel itself (current use
is for pretty printing structures).
- Support listing and getting information about bpf_links via the bpf
syscall.
- Enhance kernel interfaces around NIC firmware update. Allow
specifying overwrite mask to control if settings etc. are reset
during update; report expected max time operation may take to users;
support firmware activation without machine reboot incl. limits of
how much impact reset may have (e.g. dropping link or not).
- Extend ethtool configuration interface to report IEEE-standard
counters, to limit the need for per-vendor logic in user space.
- Adopt or extend devlink use for debug, monitoring, fw update in many
drivers (dsa loop, ice, ionic, sja1105, qed, mlxsw, mv88e6xxx,
dpaa2-eth).
- In mlxsw expose critical and emergency SFP module temperature alarms.
Refactor port buffer handling to make the defaults more suitable and
support setting these values explicitly via the DCBNL interface.
- Add XDP support for Intel's igb driver.
- Support offloading TC flower classification and filtering rules to
mscc_ocelot switches.
- Add PTP support for Marvell Octeontx2 and PP2.2 hardware, as well as
fixed interval period pulse generator and one-step timestamping in
dpaa-eth.
- Add support for various auth offloads in WiFi APs, e.g. SAE (WPA3)
offload.
- Add Lynx PHY/PCS MDIO module, and convert various drivers which have
this HW to use it. Convert mvpp2 to split PCS.
- Support Marvell Prestera 98DX3255 24-port switch ASICs, as well as
7-port Mediatek MT7531 IP.
- Add initial support for QCA6390 and IPQ6018 in ath11k WiFi driver,
and wcn3680 support in wcn36xx.
- Improve performance for packets which don't require much offloads on
recent Mellanox NICs by 20% by making multiple packets share a
descriptor entry.
- Move chelsio inline crypto drivers (for TLS and IPsec) from the
crypto subtree to drivers/net. Move MDIO drivers out of the phy
directory.
- Clean up a lot of W=1 warnings, reportedly the actively developed
subsections of networking drivers should now build W=1 warning free.
- Make sure drivers don't use in_interrupt() to dynamically adapt their
code. Convert tasklets to use new tasklet_setup API (sadly this
conversion is not yet complete).
* tag 'net-next-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2583 commits)
Revert "bpfilter: Fix build error with CONFIG_BPFILTER_UMH"
net, sockmap: Don't call bpf_prog_put() on NULL pointer
bpf, selftest: Fix flaky tcp_hdr_options test when adding addr to lo
bpf, sockmap: Add locking annotations to iterator
netfilter: nftables: allow re-computing sctp CRC-32C in 'payload' statements
net: fix pos incrementment in ipv6_route_seq_next
net/smc: fix invalid return code in smcd_new_buf_create()
net/smc: fix valid DMBE buffer sizes
net/smc: fix use-after-free of delayed events
bpfilter: Fix build error with CONFIG_BPFILTER_UMH
cxgb4/ch_ipsec: Replace the module name to ch_ipsec from chcr
net: sched: Fix suspicious RCU usage while accessing tcf_tunnel_info
bpf: Fix register equivalence tracking.
rxrpc: Fix loss of final ack on shutdown
rxrpc: Fix bundle counting for exclusive connections
netfilter: restore NF_INET_NUMHOOKS
ibmveth: Identify ingress large send packets.
ibmveth: Switch order of ibmveth_helper calls.
cxgb4: handle 4-tuple PEDIT to NAT mode translation
selftests: Add VRF route leaking tests
...
The usb_control_msg_send() and usb_control_msg_recv() calls can return
an error if a "short" write/read happens, and they can handle data off
of the stack, so move the driver over to using those calls instead,
saving some logic when dynamically allocating memory.
v2: changed API of use usb_control_msg_send() and usb_control_msg_recv()
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Link: https://lore.kernel.org/r/20200914153756.3412156-11-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20200923134348.23862-15-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
QCA Rome supports wide band speech, this patch enables the wide band
speech support by set the BTUSB_WIDEBAND_SPEECH flag.
Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The usb_control_msg_send() and usb_control_msg_recv() calls can return
an error if a "short" write/read happens, and they can handle data off
of the stack, so move the driver over to using those calls instead,
saving some logic when dynamically allocating memory.
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Link: https://lore.kernel.org/r/20200914153756.3412156-11-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
New generation controllers supports ECDSA secure boot engine.
This patch adds,
1) function to send ECDSA header
2) function to download complete firmware for new generation Intel
controllers
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Amit K Bag <amit.k.bag@intel.com>
Signed-off-by: Raghuram Hegde <raghuram.hegde@intel.com>
Reviewed-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Reviewed-by: Srivatsa Ravishankar <ravishankar.srivatsa@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
New generation Intel controllers returns version information in TLV
format. This patch adds,
1) Enums, structures for TLV
2) function to read controller information, parse TLV data and populate
intel_version_tlv structure
3) function to print version information
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Amit K Bag <amit.k.bag@intel.com>
Signed-off-by: Raghuram Hegde <raghuram.hegde@intel.com>
Reviewed-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Reviewed-by: Srivatsa Ravishankar <ravishankar.srivatsa@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Split firmware download code into two functions - one to download
header and other to download payload. This patch enhances readability
and reusabiltiy of code
Signed-off-by: Kiran K <kiran.k@intel.com>
Reviewed-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Reviewed-by: Sathish Narasimman <Sathish.Narasimman@intel.com>
Reviewed-by: Srivatsa Ravishankar <ravishankar.srivatsa@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
During serdev unregister, hdev->shutdown is called before
proto close. Removing duplicates power OFF call.
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When HCI_QUIRK_NON_PERSISTENT_SETUP is set by drivers,
it indicates that BT SoC will be completely powered OFF
during BT OFF. On next BT ON firmware must be downloaded
again. Holding UART port open during BT OFF is draining
the battery. Now during BT OFF, UART port is closed if
qurik HCI_QUIRK_NON_PERSISTENT_SETUP is set by clearing
HCI_UART_PROTO_READY proto flag. On next BT ON, UART
port is opened if HCI_UART_PROTO_READY proto flag is cleared.
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
On new Intel platform the device is provided with INT33E3 ID.
Append it to the list.
This will require ACPI_GPIO_QUIRK_ONLY_GPIOIO to be enabled because
the relevant ASL looks like:
UartSerialBusV2 ( ... )
GpioInt ( ... ) { ... }
GpioIo ( ... ) { ... }
which means that first GPIO resource is an interrupt, while we are expecting it
to be reset one (output). Do the same for host-wake because in case of
GpioInt() the platform_get_irq() will do the job and should return correct
Linux IRQ number. That said, host-wake GPIO can only be GpioIo() resource.
While here, drop commas in terminator lines.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There is no need to have list_for_each() followed by list_entry()
when we simply may use list_for_each_entry() directly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sparse rightfully complains:
hci_intel.c:696:26: warning: cast to restricted __le16
hci_intel.c:701:26: warning: cast to restricted __le16
hci_intel.c:702:26: warning: cast to restricted __le16
hci_intel.c:703:26: warning: cast to restricted __le16
hci_intel.c:725:26: warning: cast to restricted __le16
hci_intel.c:730:26: warning: cast to restricted __le16
hci_intel.c:731:26: warning: cast to restricted __le16
hci_intel.c:732:26: warning: cast to restricted __le16
because we access non-restricted types with le16_to_cpu().
More confusion is added by using above against u8. On big-endian
architecture we will get all zeroes. I bet it's not what should be
in such case.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Because clk_disable_unprepare already checked
NULL clock parameter, so the additional check is
unnecessary, just remove it.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When kmalloc() on buf fails, urb should be freed just like
when kmalloc() on dr fails.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
boot parameter gets updated during firmware download process. Use the
updated boot parameter while doing soft reset of controller. This patch
fixes updating of boot parameter.
Signed-off-by: Kiran K <kiran.k@intel.com>
Reviewed-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If hci_uart_tty_close() or hci_uart_unregister_device() is called while
hu->init_ready is scheduled, hci_register_dev() could be called after
the hci_uart is torn down. Avoid this by ensuring the work is complete
or canceled before checking the HCI_UART_REGISTERED flag.
Fixes: 9f2aee848f ("Bluetooth: Add delayed init sequence support for UART controllers")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since commit cba736465e ("Bluetooth: hci_serdev: Remove setting of
HCI_QUIRK_RESET_ON_CLOSE."), this flag is ignored for hci_serdev users,
so let's remove setting it.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
SD89xx devices use identical card register settings. Make sure a single common
instance is used to describe them.
Signed-off-by: Tamás Szűcs <tszucs@protonmail.ch>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg says:
====================
pull request: bluetooth-next 2020-07-31
Here's the main bluetooth-next pull request for 5.9:
- Fix firmware filenames for Marvell chipsets
- Several suspend-related fixes
- Addedd mgmt commands for runtime configuration
- Multiple fixes for Qualcomm-based controllers
- Add new monitoring feature for mgmt
- Fix handling of legacy cipher (E4) together with security level 4
- Add support for Realtek 8822CE controller
- Fix issues with Chinese controllers using fake VID/PID values
- Multiple other smaller fixes & improvements
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 7ecacafc24.
Testing this change on a board with RTL8822CE, I found that enabling
autosuspend has no effect on the stability of the system. The board
continued working after autosuspend, suspend and reboot.
The original commit makes it impossible to enable autosuspend on working
systems so it should be reverted. Disabling autosuspend should be done
via module param or udev in userspace instead.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Acked-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Setting memdump state to idle prior to setting of callback function
pointer for command timeout to NULL,causing the issue.Now moved the
initialisation of memdump state to qca_setup().
Fixes: d841502c79 ("Bluetooth: hci_qca: Collect controller memory dump during SSR")
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We should not call hci_unregister_dev if the device was not
successfully registered.
Fixes: c34dc3bfa7 ("Bluetooth: hci_serdev: Introduce hci_uart_unregister_device()")
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
HCI_UART_RESET_ON_INIT belongs in hdev_flags, not flags.
Fixes: ce945552fd ("Bluetooth: hci_h5: Add support for serdev enumerated devices")
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For some reason they tend to squat on the very first CSR/
Cambridge Silicon Radio VID/PID instead of paying fees.
This is an extremely common problem; the issue goes as back as 2013
and these devices are only getting more popular, even rebranded by
reputable vendors and sold by retailers everywhere.
So, at this point in time there are hundreds of modern dongles reusing
the ID of what originally was an early Bluetooth 1.1 controller.
Linux is the only place where they don't work due to spotty checks
in our detection code. It only covered a minimum subset.
So what's the big idea? Take advantage of the fact that all CSR
chips report the same internal version as both the LMP sub-version and
HCI revision number. It always matches, couple that with the manufacturer
code, that rarely lies, and we now have a good idea of who is who.
Additionally, by compiling a list of user-reported HCI/lsusb dumps, and
searching around for legit CSR dongles in similar product ranges we can
find what CSR BlueCore firmware supported which Bluetooth versions.
That way we can narrow down ranges of fakes for each of them.
e.g. Real CSR dongles with LMP subversion 0x73 are old enough that
support BT 1.1 only; so it's a dead giveaway when some
third-party BT 4.0 dongle reuses it.
So, to sum things up; there are multiple classes of fake controllers
reusing the same 0A12:0001 VID/PID. This has been broken for a while.
Known 'fake' bcdDevices: 0x0100, 0x0134, 0x1915, 0x2520, 0x7558, 0x8891
IC markings on 0x7558: FR3191AHAL 749H15143 (???)
https://bugzilla.kernel.org/show_bug.cgi?id=60824
Fixes: 81cac64ba2 (Deal with USB devices that are faking CSR vendor)
Reported-by: Michał Wiśniewski <brylozketrzyn@gmail.com>
Tested-by: Mike Johnson <yuyuyak@gmail.com>
Tested-by: Ricardo Rodrigues <ekatonb@gmail.com>
Tested-by: M.Hanny Sabbagh <mhsabbagh@outlook.com>
Tested-by: Oussama BEN BRAHIM <b.brahim.oussama@gmail.com>
Tested-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com>
Signed-off-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
1.During SSR for command time out if BT SoC goes to inresponsive
state, power cycling of BT SoC was not happening. Given the fix by
sending hw error event to reset the BT SoC.
2.If SSR is triggered then ignore the transmit data requests to
BT SoC until SSR is completed.
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds the Realtek 8822CE controller to the usb_device_id
table to support the wideband speech capability.
Signed-off-by: Joseph Hwang <josephsih@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
RTL8822CE supports transparent WBS to apply USB alternate setting 1.
Add a flag to the device match data to apply alternate setting 1 which
meet the transfer speed for WBS support.
Signed-off-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add a comment clarifying that a PM reference in btusb_qca_cmd_timeout is
not unbalanced because it results in a device reset.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Address the scalability to support new generation Intel controller with
respect to readability and enhancement to new firmware download sequence
Signed-off-by: Kiran K <kiran.k@intel.com>
Reviewed-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the BTUSB_WAKEUP_DISABLE flag is set, always return true for
prevent wake. This tells the suspend notifier not to prepare the
controller for reconnections during suspend.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
QCA_ROME sometimes gets into a state where it is unresponsive to
commands. Since it doesn't have support for a reset gpio, reset the usb
port when this occurs instead.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Data RAM on the device have to be powered on before starting to download
the firmware.
Fixes: 9aebfd4a22 ("Bluetooth: mediatek: add support for MediaTek MT7663S and MT7668S SDIO devices")
Co-developed-by: Mark Chen <Mark-YW.Chen@mediatek.com>
Signed-off-by: Mark Chen <Mark-YW.Chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Data RAM on the device have to be powered on before starting to download
the firmware.
Fixes: a1c49c434e ("Bluetooth: btusb: Add protocol support for MediaTek MT7668U USB devices")
Co-developed-by: Mark Chen <Mark-YW.Chen@mediatek.com>
Signed-off-by: Mark Chen <Mark-YW.Chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Tx pending flag is set to true when HOST IBS state is AWAKE or
AWAKEING. If IBS state is ASLEEP, then Tx clock is already voted
off. To optimize further directly calling serial_clock_vote()
instead of qca_wq_serial_tx_clock_vote_off(), at this point of
qca_suspend() already data is sent out. No need to wake up hci to
send data.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In some version of WCN399x, SoC idle timeout is configured
as 80ms instead of 20ms or 40ms. To honor all the SoC's
supported in the driver increasing SoC idle timeout to 200ms.
Fixes: 41d5b25fed ("Bluetooth: hci_qca: add PM support")
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
By default, WCN3991 sent debug packets to HOST via ACL packet
with header 0xDC2E. This logging is not required on commercial
devices. With this patch SoC logging is disabled post fw
download.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use device_init_wakeup to allow the Bluetooth dev to wake the system
from suspend. Currently, the device can wake the system but no
power/wakeup entry is created in sysfs to allow userspace to disable
wakeup.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use the parent device's power/wakeup to control whether we support
remote wake. If remote wakeup is disabled, Bluetooth will not enable
scanning for incoming connections.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Set the correct parent dev when registering hdev. This allows userspace
tools to find the parent device (for example, to set the power/wakeup
property).
Before this change, the path was /sys/devices/virtual/bluetooth/hci0
and after this change, it looks more like:
/sys/bus/mmc/devices/mmc1:0001/mmc1:0001:2/bluetooth/hci0
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch shall enable the Intel telemetry exception format
based on the supported features
Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: Ps AyappadasX <AyappadasX.Ps@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The command shall read the Intel controller supported
debug feature. Based on the supported features additional debug
configuration shall be enabled.
Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: Ps AyappadasX <AyappadasX.Ps@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Due to race conditions between qca_hw_error and qca_controller_memdump
during SSR timeout,the same pointer is freed twice. This results in a
double free. Now a lock is acquired before checking the stauts of SSR
state.
Fixes: d841502c79 ("Bluetooth: hci_qca: Collect controller memory dump during SSR")
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If waiting for IBS sleep times out jump to the error handler, this is
easier to read than multiple 'if' branches and a fall through to the
error handler.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
qca_suspend() calls serdev_device_wait_until_sent() regardless of
whether a transfer is pending. While it does no active harm since
the function should return immediately it makes the code more
confusing. Add a flag to track whether a transfer is pending and
only call serdev_device_wait_until_sent() is needed.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
qca_suspend() removes the vote for the UART TX clock after
writing an IBS sleep request to the serial buffer. This is
not a good idea since there is no guarantee that the request
has been sent at this point. Instead remove the vote after
successfully entering IBS sleep. This also fixes the issue
of the vote being removed in case of an aborted suspend due
to a failure of entering IBS sleep.
Fixes: 41d5b25fed ("Bluetooth: hci_qca: add PM support")
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The serial clocks should be on when there is a vote for at least one
of the clocks (RX or TX), and off when there is no 'on' vote. The
current logic to determine the combined state is a bit redundant
in the code paths for different types of votes, use a single
statement in the common path instead.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
When a function like devm_clk_get_optional() function returns both error
pointers on error and NULL then the NULL return means that the optional
feature is deliberately disabled. It is a special sort of success and
should not trigger an error message. The surrounding code should be
written to check for NULL and not crash.
On the other hand, if we encounter an error, then the probe from should
clean up and return a failure.
In this code, if devm_clk_get_optional() returns an error pointer then
the kernel will crash inside the call to:
clk_set_rate(qcadev->susclk, SUSCLK_RATE_32KHZ);
The error handling must be updated to prevent that.
Fixes: 77131dfec6 ("Bluetooth: hci_qca: Replace devm_gpiod_get() with devm_gpiod_get_optional()")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Firmware for sd8997 chipset is distributed by Marvell package and also as
part of the linux-firmware repository in filename sdsd8997_combo_v4.bin.
This patch fixes mwifiex driver to load correct firmware file for sd8997.
Fixes: f0ef67485f ("Bluetooth: btmrvl: add sd8997 chipset support")
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Firmware for sd8977 chipset is distributed by Marvell package and also as
part of the linux-firmware repository in filename sdsd8977_combo_v2.bin.
This patch fixes mwifiex driver to load correct firmware file for sd8977.
Fixes: 8c57983bf7 ("Bluetooth: btmrvl: add support for sd8977 chipset")
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
QCA6390 memdump VSE sometimes come to bluetooth driver
with wrong sequence number as illustrated as follows:
frame # in dec: frame data in hex
1396: ff fd 01 08 74 05 00 37 8f 14
1397: ff fd 01 08 75 05 00 ff bf 38
1414: ff fd 01 08 86 05 00 fb 5e 4b
1399: ff fd 01 08 77 05 00 f3 44 0a
1400: ff fd 01 08 78 05 00 ca f7 41
it is mistook for controller missing packets, so results
in page fault after overwriting memdump buffer allocated.
Fixed by ignoring QCA6390 sequence number check and
checking buffer space before writing.
Signed-off-by: Zijun Hu <zijuhu@codeaurora.org>
Tested-by: Zijun Hu <zijuhu@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
serdev_device_write() is not appropriate at here because
serdev_device_write_wakeup() is not used to release completion hold
by the former at @write_wakeup member of struct serdev_device_ops.
Fix by using serdev_device_write_buf() instead of serdev_device_write().
Signed-off-by: Zijun Hu <zijuhu@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Controller ID info got by VSC EDL_PATCH_GETVER is very
important, so improve its log level from DEBUG to INFO.
Signed-off-by: Zijun Hu <zijuhu@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Warm reboot can not reset controller qca6390 due to
lack of controllable power supply, so causes firmware
download failure during enable.
Fixed by sending VSC EDL_SOC_RESET to reset qca6390
within added device shutdown implementation.
Signed-off-by: Zijun Hu <zijuhu@codeaurora.org>
Tested-by: Zijun Hu <zijuhu@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Calls of the functions clk_disable_unprepare() and hci_free_dev()
were missing for the exception handling.
Thus add the missed function calls together with corresponding
jump targets.
Fixes: 055825614c ("Bluetooth: btmtkuart: add an implementation for clock osc property")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
@dev parameter of qca_suspend()/qca_resume() represents
serdev_device, but it is mistook for hci_dev and causes
succedent unexpected memory access.
Fix by taking @dev as serdev_device.
Fixes: 41d5b25fed ("Bluetooth: hci_qca: add PM support")
Signed-off-by: Zijun Hu <zijuhu@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Added new Broadcom device BCM4350C5, changed BCM4354A2 to BCM4356A2.
Based on Broadcom Windows drivers 001.003.015 should be BCM4356A2. I
have user report that firmware name is misplaced
(https://github.com/winterheart/broadcom-bt-firmware/issues/3).
Signed-off-by: Azamat H. Hackimov <azamat.hackimov@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
hdev is always allocated and not only when power control is required.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
WCN3991 supports transparent WBS (host encoded mSBC). Add a flag to the
device match data to show WBS is supported.
This requires the matching firmware for WCN3991 in linux-firmware:
1a8b0dc00f77 (qca: Enable transparent WBS for WCN3991)
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
serdev_device_ops is not modified and can be const. Also, remove the
unneeded declaration of it.
Output from the file command before and after:
Before:
text data bss dec hex filename
7192 2408 192 9792 2640 drivers/bluetooth/hci_serdev.o
After:
text data bss dec hex filename
7256 2344 192 9792 2640 drivers/bluetooth/hci_serdev.o
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Implement the prevent_wake hook by checking device_may_wakeup on the usb
interface. This prevents the Bluetooth core from enabling scanning when
the device isn't expected to wake from suspend.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
RTL8723BS is often used in ARM boards, so add ability to bind it
using device tree.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Alistair Francis <alistair@alistair23.me>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Move the read of max-speed from device-tree out of the qca_is_wcn399x
if block so oper_speed can be set for QCA9377 devices as well.
Suggested-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add a compatible so QCA9377 devices can be defined in device-tree.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This change adds support for LE scatternet connections to Intel's JfP
and ThP controllers.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This change adds the relevant driver and quirk to allow drivers to
report the le_states as being trustworthy.
This has historically been disabled as controllers did not reliably
support this. In particular, this will be used to relax this condition
for controllers that have been well tested and reliable.
/* Most controller will fail if we try to create new connections
* while we have an existing one in slave role.
*/
if (hdev->conn_hash.le_num_slave > 0)
return NULL;
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently the bcm_uart_subver_ and bcm_usb_subver_table-s lack entries
for the BCM4324B5 and BCM20703A1 chipsets. This makes the code use just
"BCM" as prefix for the filename to pass to request-firmware, making it
harder for users to figure out which firmware they need. This especially
is problematic with the UART attached BCM4324B5 where this leads to the
filename being just "BCM.hcd".
Add the 2 missing devices to subver tables. This has been tested on:
1. A Dell XPS15 9550 where this makes btbcm.c try to load
"BCM20703A1-0a5c-6410.hcd" before it tries to load "BCM-0a5c-6410.hcd".
2. A Thinkpad 8 where this makes btbcm.c try to load
"BCM4324B5.hcd" before it tries to load "BCM.hcd"
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently the bcm_uart_subver_ and bcm_usb_subver_table-s lack entries
for various newer chipsets. This makes the code use just "BCM" as prefix
for the filename to pass to request-firmware, making it harder for users
to figure out which firmware they need. This especially a problem with
UART attached devices where this leads to the filename being "BCM.hcd".
If we add new entries to the subver-tables now, then this will change
what firmware file the kernel looks for, e.g. currently linux-firmware
contains a brcm/BCM-0bb4-0306.hcd file. If we add the info for the
BCM20703A1 to the subver table, then this will change to
brcm/BCM20703A1-0bb4-0306.hcd. This will cause the file to no longer
get loaded breaking Bluetooth for existing users, going against the
no regressions policy.
To avoid this regression make the btbcm code try multiple filenames,
first try the fullname, e.g. BCM20703A1-0bb4-0306.hcd and if that is
not found, then fallback to the name with just BCM as prefix.
This commit also adds an info message which filename was used,
this makes the output look like this for example:
[ 57.387867] Bluetooth: hci0: BCM20703A1
[ 57.387870] Bluetooth: hci0: BCM20703A1 (001.001.005) build 0000
[ 57.389438] Bluetooth: hci0: BCM20703A1 'brcm/BCM20703A1-0a5c-6410.hcd' Patch
[ 58.681769] Bluetooth: hci0: BCM20703A1 Generic USB 20Mhz fcbga_BU
[ 58.681772] Bluetooth: hci0: BCM20703A1 (001.001.005) build 0481
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If we have already loaded the firmware/patchram and btbcm_initialize()
is called to re-init the HCI after this then there is no need to get
the USB device-ids and build a firmware-filename out of these.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
On UART attached devices we do:
1. btbcm_initialize()
2. Setup UART baudrate, etc.
3. btbcm_finalize()
After our previous changes we can now also use btbcm_finalize() from
the btbcm_setup_patchram() function used on USB devices without any
functional changes. This completes unifying the USB and UART paths
as much as possible.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Make btbcm_initialize() get and print the device's local-name on re-init
too, this will make us also print the local-name after loading the
Patch on UART attached devices making things more consistent.
This also removes some code duplication from btbcm_setup_patchram()
and allows more code duplication removal there in a follow-up patch.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Instead of having btbcm_initialize() fill a passed in fw_name buffer
and then have its callers use that to request the firmware + load
it into the HCI, make btbcm_initialize() do this itself the first
time it is called (its get called a second time to reset the HCI
after the firmware has been loaded).
This removes some code duplication and makes it easier for further
patches in this series to try more then 1 firmware filename.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
btbcm_finalize() is currently only used by UART attached BCM devices.
Move the setting of the USE_BDADDR_PROPERTY quirk, which we only want
for UART attached devices to hci_bcm in preparation for using
btbcm_finalize() for USB attached devices too.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
btbcm_initialize() must either return an error; or fill the passed in
fw_name, otherwise we end up passing uninitialized stack memory to
request_firmware().
Since we have a fallback hw_name of "BCM" not having a known version
in the subver field does not matter, drop the check so that we always
fill the passed in fw_name.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The new btusb_find_altsetting() dereferences it without checking
the check is added in this patch
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In case the controller is already in operation mode, the Intel specific
events will not be enabled. Fix this by jumping to a common finish
section that will allow setting final details for the controller.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
For mSBC encoded audio stream over usb transport, btusb driver
to be set to alternate settings 6 as per BT core spec 5.0. The
type of air mode is used to differenting which alt setting to be
used.
The changes are made considering some discussion over the similar
patch submitted earlier from Kuba Pawlak (link below)
https://www.spinics.net/lists/linux-bluetooth/msg64577.html
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: Hsin-Yu Chao <hychao@chromium.org>
Signed-off-by: Amit K Bag <amit.k.bag@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When BT module can't be initialized, but it has an IRQ, unloading
the driver WARNs when trying to free not-yet-requested IRQ. Fix it by
noting whether the IRQ was requested.
WARNING: CPU: 2 PID: 214 at kernel/irq/devres.c:144 devm_free_irq+0x49/0x4ca
[...]
WARNING: CPU: 2 PID: 214 at kernel/irq/manage.c:1746 __free_irq+0x8b/0x27c
Trying to free already-free IRQ 264
Modules linked in: hci_uart(-) btbcm bluetooth ecdh_generic ecc libaes
CPU: 2 PID: 214 Comm: rmmod Tainted: G W 5.6.1mq-00044-ga5f9ea098318-dirty #928
[...]
[<b016aefb>] (devm_free_irq) from [<af8ba1ff>] (bcm_close+0x97/0x118 [hci_uart])
[<af8ba1ff>] (bcm_close [hci_uart]) from [<af8b736f>] (hci_uart_unregister_device+0x33/0x3c [hci_uart])
[<af8b736f>] (hci_uart_unregister_device [hci_uart]) from [<b035930b>] (serdev_drv_remove+0x13/0x20)
[<b035930b>] (serdev_drv_remove) from [<b037093b>] (device_release_driver_internal+0x97/0x118)
[<b037093b>] (device_release_driver_internal) from [<b0370a0b>] (driver_detach+0x2f/0x58)
[<b0370a0b>] (driver_detach) from [<b036f855>] (bus_remove_driver+0x41/0x94)
[<b036f855>] (bus_remove_driver) from [<af8ba8db>] (bcm_deinit+0x1b/0x740 [hci_uart])
[<af8ba8db>] (bcm_deinit [hci_uart]) from [<af8ba86f>] (hci_uart_exit+0x13/0x30 [hci_uart])
[<af8ba86f>] (hci_uart_exit [hci_uart]) from [<b01900bd>] (sys_delete_module+0x109/0x1d0)
[<b01900bd>] (sys_delete_module) from [<b0101001>] (ret_fast_syscall+0x1/0x5a)
[...]
Cc: stable@vger.kernel.org
Fixes: 6cc4396c88 ("Bluetooth: hci_bcm: Add wake-up capability")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The IRQ polarity is be configured in bcm_setup_sleep(). Make the
configured value match what is in the DeviceTree.
Cc: stable@vger.kernel.org
Fixes: f25a96c8eb ("Bluetooth: hci_bcm: enable IRQ capability from devicetree")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for QCA6390, including the devicetree and acpi
compatible hwid matching, and patch/nvm downloading.
Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To determine the build version of Bluetooth firmware to ensure reported
issue related to a particular release. This is very helpful for every fw
downloaded to BT controller and issue reported from field test.
Signed-off-by: Amit K Bag <amit.k.bag@intel.com>
Signed-off-by: Sukumar Ghorai <sukumar.ghorai@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
All HCI device specific error messages shall use bt_dev_err to indicate
the device name in the message.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
All HCI device specific error messages shall use bt_dev_err to indicate
the device name in the message.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This change introduces a wide band speech setting which allows higher
level clients to query the local controller support for wide band speech
as well as set the setting state when the radio is powered off.
Internally, this setting controls if erroneous data reporting is enabled
on the controller.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch replaces devm_gpiod_get() with devm_gpiod_get_optional() to get
bt_en and replaces devm_clk_get() with devm_clk_get_optional() to get
susclk. It also uses NULL check to determine whether the resource is
available or not.
Fixes: 8a208b24d7 ("Bluetooth: hci_qca: Make bt_en and susclk not mandatory for QCA Rome")
Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
On some platforms the bt_en pin and susclk are default on and there
is no exposed resource to control them. This patch makes the bt_en
and susclk not mandatory to have BT work. It also will not set the
HCI_QUIRK_NON_PERSISTENT_SETUP and shutdown() callback if bt_en is
not available.
Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The baudrate set byte of wcn3991 in the NVM tag is byte 1, not byte 2.
This patch will set correct byte for wcn3991.
Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Mark Chen