Fix some spelling errors and inconsistencies in comment blocks.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
this patch avoids a denial of service from an evildoer sending a
continuous stream of flow control at our adapter that is plugged
into a non-flow control enabled switch.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This simplifies the 82571/2/3 family initialization a bit
and removes an initialization table no longer needed.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This counter is valuable to determine if the system is unable
to timely return buffers to the hardware and this counter starts
to increase well before the hardware starts to drop packets. If
users experience rx_no_buffer_count increasing, they should increase
the amount of descriptors. That will provide more buffers for the
hardware and will decrease the chance of hard drops.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix NCFGR.SPD setting on 10Mbps. This bug was introduced by
conversion to generic PHY layer in kernel 2.6.23.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix problems in LED management, so ethtool -p works correctly on Yukon-EC
and other chips. The driver was incorrectly setting the PHY LED overide bits.
Moral: read the spec sheet, not the vendor driver.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use register offset definition for WOLcgClr, rather than a magic
number.
This patch does not change the driver behaviour.
Signed-off-by: Laura Garcia Liebana <nevola@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes a check-after-use spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch eliminates a kernel panic with the igb driver in 2.6.25-rc2 when
running on a Intel 82575 Ethernet controller with a 1000BASE-SX PHY. The
panic does not happen with the 1000BASE-T PHY, only with a SX connection.
Signed-off-by: Bill Hayes <bill.hayes@hp.com>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Change all dma op invocations in gianfar.c to actually pass in the
device pointer. Currently, the value is ignored, but it will be
used going forward as we implement archdata for 32-bit powerpc.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reading a serie of zero from the cmos sram area do not work
well with is_valid_ether_addr(). Let's read the mac address
from the eeprom first as it seems more reliable.
Fix for http://bugzilla.kernel.org/show_bug.cgi?id=9831
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The forward declarations were already marked static, make the definitions
be static as well. Fixes the sparse warnings as well.
drivers/net/tlan.c:1403:5: warning: symbol 'TLan_HandleInvalid' was not declared. Should it be static?
drivers/net/tlan.c:1435:5: warning: symbol 'TLan_HandleTxEOF' was not declared. Should it be static?
drivers/net/tlan.c:1521:5: warning: symbol 'TLan_HandleStatOverflow' was not declared. Should it be static?
drivers/net/tlan.c:1557:5: warning: symbol 'TLan_HandleRxEOF' was not declared. Should it be static?
drivers/net/tlan.c:1692:5: warning: symbol 'TLan_HandleDummy' was not declared. Should it be static?
drivers/net/tlan.c:1722:5: warning: symbol 'TLan_HandleTxEOC' was not declared. Should it be static?
drivers/net/tlan.c:1770:5: warning: symbol 'TLan_HandleStatusCheck' was not declared. Should it be static?
drivers/net/tlan.c:1845:5: warning: symbol 'TLan_HandleRxEOC' was not declared. Should it be static?
drivers/net/tlan.c:1905:6: warning: symbol 'TLan_Timer' was not declared. Should it be static?
drivers/net/tlan.c:1986:6: warning: symbol 'TLan_ResetLists' was not declared. Should it be static?
drivers/net/tlan.c:2046:6: warning: symbol 'TLan_FreeLists' was not declared. Should it be static?
drivers/net/tlan.c:2095:6: warning: symbol 'TLan_PrintDio' was not declared. Should it be static?
drivers/net/tlan.c:2130:6: warning: symbol 'TLan_PrintList' was not declared. Should it be static?
drivers/net/tlan.c:2166:6: warning: symbol 'TLan_ReadAndClearStats' was not declared. Should it be static?
drivers/net/tlan.c:2242:1: warning: symbol 'TLan_ResetAdapter' was not declared. Should it be static?
drivers/net/tlan.c:2328:1: warning: symbol 'TLan_FinishReset' was not declared. Should it be static?
drivers/net/tlan.c:2451:6: warning: symbol 'TLan_SetMac' was not declared. Should it be static?
drivers/net/tlan.c:2493:6: warning: symbol 'TLan_PhyPrint' was not declared. Should it be static?
drivers/net/tlan.c:2542:6: warning: symbol 'TLan_PhyDetect' was not declared. Should it be static?
drivers/net/tlan.c:2589:6: warning: symbol 'TLan_PhyPowerDown' was not declared. Should it be static?
drivers/net/tlan.c:2614:6: warning: symbol 'TLan_PhyPowerUp' was not declared. Should it be static?
drivers/net/tlan.c:2635:6: warning: symbol 'TLan_PhyReset' was not declared. Should it be static?
drivers/net/tlan.c:2663:6: warning: symbol 'TLan_PhyStartLink' was not declared. Should it be static?
drivers/net/tlan.c:2750:6: warning: symbol 'TLan_PhyFinishAutoNeg' was not declared. Should it be static?
drivers/net/tlan.c:2906:5: warning: symbol 'TLan_MiiReadReg' was not declared. Should it be static?
drivers/net/tlan.c:2996:6: warning: symbol 'TLan_MiiSendData' was not declared. Should it be static?
drivers/net/tlan.c:3038:6: warning: symbol 'TLan_MiiSync' was not declared. Should it be static?
drivers/net/tlan.c:3077:6: warning: symbol 'TLan_MiiWriteReg' was not declared. Should it be static?
drivers/net/tlan.c:3147:6: warning: symbol 'TLan_EeSendStart' was not declared. Should it be static?
drivers/net/tlan.c:3187:5: warning: symbol 'TLan_EeSendByte' was not declared. Should it be static?
drivers/net/tlan.c:3248:6: warning: symbol 'TLan_EeReceiveByte' was not declared. Should it be static?
drivers/net/tlan.c:3306:5: warning: symbol 'TLan_EeReadByte' was not declared. Should it be static?
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* If ConfigBase is 0x03c0 && manfid is (0x0149,0xc1ab),
printk "use axnet_cs instead" message.
Actually, most of the card with manfid(0x0149, 0xc1ab)
use pcnet_cs driver.
* remove entry (0x021b, 0x0202)
Signed-off-by: Komuro <komurojun-mbn@nifty.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Suppress the warning message about the 'netcard_portlist' defined but not used.
Signed-off-by: Leonardo Potenza <lpotenza@inwind.it>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Patch fixes:
http://bugzilla.kernel.org/show_bug.cgi?id=5839
Init sequence needs to poll phy until phy reset is complete. This is the
same problem that I fixed in 2002 in tulip driver.
Thanks to manty@manty.net for testing this patch.
Thanks to Pozsar Balazs <pozsy@uhulinux.hu> for posting/testing
a similar patch before:
http://lkml.org/lkml/2006/8/21/45
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
I booted an igb kernel with the option pci=nomsi and instantly noticed
that interrupts no longer worked on my igb device. I took a look at the
interrupt initialization and quickly discovered a comment stating:
"DO NOT USE EIAME or IAME in legacy mode"
It seemed a bit odd that bits to enable IAM were being set in legacy
interrupt mode, so I dropped out the following parts and interrupts
began working fine again.
[Updated code flow and a nitpick spelling error --Auke]
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The lock acquisition in fs_ioctl() does not appear to actually be necessary,
and thus is simply removed.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds kdump support to the ehea driver. As the firmware doesn't free
resource handles automatically, the driver has to run an as simple as possible
free resource function in case of a crash shutdown. The function iterates over
two arrays freeing all resource handles which are stored there. The arrays are
kept up-to-date during normal runtime. The crash handler fn is triggered by the
recently introduced PPC crash shutdown reg/unreg functions.
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When asked to blink LEDs the tg3 driver behaves when using:
ethtool -p ethX
The default value for data is zero, and other drivers interpret this
as blink forever (or at least a really long time). The tg3 driver
interprets this as blink once. All drivers should have the same
behaviour.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because of some board issues, we need to disable parallel detect on
an HP blade. Without this patch, the link state can become stuck
when it goes into parallel detect mode.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous patches to workaround the 5706S on an HP blade were not
sufficient. The link state still does not change properly in some
cases. This patch adds polling to make it completely reliable.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This silences sparse when run on zd1211rw.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This silences a few sparse warnings. There are two more where
I can't follow the code.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
'u64' is not necessarily 'unsigned long long'
drivers/net/wireless/ath5k/base.c: In function 'ath5k_beacon_update_timers':
drivers/net/wireless/ath5k/base.c:2130: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'u64'
drivers/net/wireless/ath5k/base.c:2130: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'u64'
drivers/net/wireless/ath5k/base.c: In function 'ath5k_intr':
drivers/net/wireless/ath5k/base.c:2391: warning: format '%llx' expects type 'long long unsigned int', but argument 6 has type 'u64'
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sparse sees int -> bool cast as an error:
hw.c:3754:10: warning: cast truncates bits from constant value (ffffffea becomes 0)
Fix it by converting the rettype to int and check appropriately.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Omitted lock causes sparse warning
drivers/net/wireless/ath5k/base.c:1682:1: warning: context imbalance in 'ath5k_tasklet_rx' - different lock contexts for basic block
Add the lock to the guilty fail path.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on report from Cavan Carroll <cavancarroll@hotmail.com>:
http://bugzilla.kernel.org/show_bug.cgi?id=9863
Cc: Cavan Carroll <cavancarroll@hotmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When deleting the veth driver, veth_close calls netif_carrier_off
for the two extremities of the network device. netif_carrier_off on
the peer device will fire an event and hold a reference on the peer
device. Just after, the peer is unregistered taking the rtnl_lock while
the linkwatch_event is scheduled. If __linkwatch_run_queue does not
occurs before the unregistering, unregister_netdevice will wait for
the dev refcount to reach zero holding the rtnl_lock and linkwatch_event
will wait for the rtnl_lock and hold the dev refcount.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Matheos Worku <Matheos.Worku@Sun.COM>
1) niu_enable_alt_mac() needs to be adjusted so that the mask
is computed properly for the BMAC case.
2) BMAC has 6 alt MAC addresses available, not 7.
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (60 commits)
[NIU]: Bump driver version and release date.
[NIU]: Fix BMAC alternate MAC address indexing.
net: fix kernel-doc warnings in header files
[IPV6]: Use BUG_ON instead of if + BUG in fib6_del_route.
[IPV6]: dst_entry leak in ip4ip6_err. (resend)
bluetooth: do not move child device other than rfcomm
bluetooth: put hci dev after del conn
[NET]: Elminate spurious print_mac() calls.
[BLUETOOTH] hci_sysfs.c: Kill build warning.
[NET]: Remove MAC_FMT
net/8021q/vlan_dev.c: Use print_mac.
[XFRM]: Fix ordering issue in xfrm_dst_hash_transfer().
[BLUETOOTH] net/bluetooth/hci_core.c: Use time_* macros
[IPV6]: Fix hardcoded removing of old module code
[NETLABEL]: Move some initialization code into __init section.
[NETLABEL]: Shrink the genl-ops registration code.
[AX25] ax25_out: check skb for NULL in ax25_kick()
[TCP]: Fix tcp_v4_send_synack() comment
[IPV4]: fix alignment of IP-Config output
Documentation: fix tcp.txt
...
BMAC port alternate MAC address index needs to start at 1. Index 0 is
used for the main MAC address.
Signed-off-by: Matheos Worku <matheos.worku@sun.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the removal the the "rgmii-interface" device_type property from the
dts files, the newemac driver needs an update to only rely on compatible
property.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds printk messages with basic information about the driver being loaded.
This information includes a summary of the compiled-in features, which
simplifies bug-reporting and debugging a lot.
Also a firmware ID is printed. This is a unique identifier blob for a specific
version of the firmware. This ID is attached to a specific version of the firmware
blob in b43-fwcutter (see fwcutter git).
This helps users to select the right firmware for their device.
This also makes it possible to use automated scripts to fetch and extract the right
firmware for the driver. (The script will grep the .ko for the "Firmware-ID: xxx" string.)
While the driver might still support other versions of the firmware for backward
compatibility, this will always print out the officially supported version, which
people _should_ use.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Restock the RX queue when there are a lot of unused frames so that the
RX ring buffer doesn't overrun, causing a ucode assertion. Backport of
patch "iwlwifi: fix ucode assertion for RX queue overrun".
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no association process in IBSS mode - so testing the
association id is not needed.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
CC: Richard Scherping <richard@scherping.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch revert commit blow that wrongly suppressed sparse warning in
iwlwifi eeprom reading
In addtion it suppresses correctly the iwlwifi eeprom register reading anomaly.
commit 45883ae47a0a4700c0f4716dc75a255cccdc3a76
misc wireless annotations
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware version information should always get printed. Not only on a
debug build.
The patch by Michael Buesch has been ported to b43legacy.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds the firmware ID to modinfo.
The patch by Michael Buesch has been ported to b43legacy.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware version information should always get printed. Not only
on a debug build.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds printk messages with basic information about the driver being loaded.
This information includes a summary of the compiled-in features, which
simplifies bug-reporting and debugging a lot.
Also a firmware ID is printed. This is a unique identifier blob for a specific
version of the firmware. This ID is attached to a specific version of the firmware
blob in b43-fwcutter (see fwcutter git).
This helps users to select the right firmware for their device.
This also makes it possible to use automated scripts to fetch and extract the right
firmware for the driver. (the script will grep the .ko for the "Firmware-ID: xxx" string.
While the driver might still support other versions of the firmware for backward
compatibility, this will always print out the officially supported version, which
people _should_ use.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This checks if the DMA address is bigger than what the controller can manage.
It will reallocate the buffers in the GFP_DMA zone in that case.
The patch by Michael Buesch has been ported to b43legacy.
Thanks to Matti Viljanen for reporting this.
Cc: Matti Viljanen <viljanen.matti@gmail.com>
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Value of count is used to decide when to replenish rx buffers. If it is
equal or above 8 we replenish the buffers. Ensure there is no starvation
by initializing count to 8 - thus forcing replenish at first iteration.
This is helpful when rx receives batches of buffers smaller than 8.
Signed-off-by: Mohamed Abbas <mabbas@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch prevents sending host commands when rfkill is on
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The geos information is set up during probe and should only
be removed during pci_remove, not during _down.
This is a temporary fix until the setting of the status bits
have been cleaned up (to explicitly match all setting with
clearing of status bits).
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable workaround for poor link stalls by link quality instead of link
speed. Using link speed caused workaround be active always on 802.11b
networks which reduced performance and not even catch all stalls.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
when setting up the tx descriptors for the hardware we must account for any
padding between the header and the data we might have added previously. frame
len is the length of the frame in the air (including FCS but no padding) and
buffer len is the length of the buffer (including padding, but without FCS).
changing the way ah_setup_tx_desc is called: now excluding the FCS, since it's
easier to add that in the function where we need it.
before this fix we sent trailing zero bytes after the packet (because frame len
included the padding) which was not a big problem without WEP, but with WEP
this resultes in a wrong WEP checksum and the packet is discarded - which is
how i noticed at all ;)
an easy way to run into header padding problems, btw, is to connect to a QoS
(WME) enabled access point (eg. madwifi) - QoS data frames are 2 byte longer
and will require padding.
this patch applies on top of luis latest patch series from 04.02.2008.
drivers/net/wireless/ath5k/base.c: Changes-licensed-under: 3-Clause-BSD
drivers/net/wireless/ath5k/hw.c: Changes-licensed-under: ISC
Signed-off-by: Bruno Randolf <bruno@thinktube.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With assists from Russell King <rmk+kernel@arm.linux.org.uk> and
Andrew Morton <akpm@linux-foundation.org>...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Users reported that ARP's were lost with e1000e. The problem
is fixed by not enabling this manageability configuration
bit.
None of the release_manageability code is actually needed as the
normal device reset during a shutdown returns everthing to
the right condition automatically.
Signed-off-by: David Graham <david.graham@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Users reported that ARP's were lost with igb. The problem
is fixed by not enabling this manageability configuration
bit.
None of the release_manageability code is actually needed as the
normal device reset during a shutdown returns everthing to
the right condition automatically.
Signed-off-by: David Graham <david.graham@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In reply to "RE: [Fwd: [PATCH 2.6.25] ixgbe/igb: correctly obtain protocol
information on transmit]" from Andy Gospodarek:
The driver was incorrectly looking at socket headers for
protocol information, needed for checksumming offload. Fix
this by not looking at the socket but frame headers instead.
This disregards extension headers but it's unclear that linux
generates those anyway.
Tested by Andy Gospodarek.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
CRC stripping was only correctly enabled for packet split recieves
which is used when receiving jumbo frames. Correctly enable SECRC
also for normal buffer packet receives.
Tested by Andy Gospodarek and Johan Andersson, see bugzilla #9940.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
According to one of OOPSes reported by Jann softirq can break
while skb is prepared for netif_rx. The report isn't complete,
so the real reason of the later bug could be different, but
IMHO this locking break in ax_bump is unsafe and unnecessary.
Reported-and-tested-by: Jann Traschewski <jann@gmx.de>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Megahertz EM1144 PCMCIA ethernet adapter needs special handling
because it has two VERS_1 tuples and the station address is in
the second one. Conversion to generic handling of these fields
broke it. Reverting that fixes the device.
https://bugzilla.redhat.com/show_bug.cgi?id=233255
Thanks go to Jon Stanley for not giving up on this one until the
problem was found.
Signed-off-by: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (82 commits)
[NET]: Make sure sockets implement splice_read
netconsole: avoid null pointer dereference at show_local_mac()
[IPV6]: Fix reversed local_df test in ip6_fragment
[XFRM]: Avoid bogus BUG() when throwing new policy away.
[AF_KEY]: Fix bug in spdadd
[NETFILTER] nf_conntrack_proto_tcp.c: Mistyped state corrected.
net: xfrm statistics depend on INET
[NETFILTER]: make secmark_tg_destroy() static
[INET]: Unexport inet_listen_wlock
[INET]: Unexport __inet_hash_connect
[NET]: Improve cache line coherency of ingress qdisc
[NET]: Fix race in dev_close(). (Bug 9750)
[IPSEC]: Fix bogus usage of u64 on input sequence number
[RTNETLINK]: Send a single notification on device state changes.
[NETLABLE]: Hide netlbl_unlabel_audit_addr6 under ifdef CONFIG_IPV6.
[NETLABEL]: Don't produce unused variables when IPv6 is off.
[NETLABEL]: Compilation for CONFIG_AUDIT=n case.
[GENETLINK]: Relax dances with genl_lock.
[NETLABEL]: Fix lookup logic of netlbl_domhsh_search_def.
[IPV6]: remove unused method declaration (net/ndisc.h).
...
This patch avoids a null pointer dereference when we read local_mac
for netconsole in configfs and shows default local mac address
value.
A null pointer dereference occurs when we call show_local_mac() via
local_mac entry in configfs before we setup the content of netpoll
using netpoll_setup().
Signed-off-by: Keiichi KII <k-keiichi@bx.jp.nec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4_table_find (for FMR MPTs) requires that ICM memory already be
mapped. Before this fix, FMR allocation depended on ICM memory
already being mapped for the MPT entry. If all currently mapped
entries are taken, the find operation fails (even if the MPT ICM table
still had more entries, which were just not mapped yet).
This fix moves the mpt find operation to fmr_enable, to guarantee that
any required ICM memory mapping has already occurred.
Found by Oren Duer of Mellanox.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit 313abe55 ("mlx4_core: For 64-bit systems, vmap() kernel queue
buffers") caused this to pop up on powerpc allyesconfig, looks like a
missing include file:
drivers/net/mlx4/alloc.c: In function 'mlx4_buf_alloc':
drivers/net/mlx4/alloc.c:162: error: implicit declaration of function 'vmap'
drivers/net/mlx4/alloc.c:162: error: 'VM_MAP' undeclared (first use in this function)
drivers/net/mlx4/alloc.c:162: error: (Each undeclared identifier is reported only once
drivers/net/mlx4/alloc.c:162: error: for each function it appears in.)
drivers/net/mlx4/alloc.c:162: warning: assignment makes pointer from integer without a cast
drivers/net/mlx4/alloc.c: In function 'mlx4_buf_free':
drivers/net/mlx4/alloc.c:187: error: implicit declaration of function 'vunmap'
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
It's easy to oversee this issue when working with this card
as evrything will work OK but performance is severely limited
(something like 1.5gbit on a x1 link) if the pci-express
slot does not offer more bandwidth.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A logic mishap caused the adapter to keep link while we can
disable it due to WoL not being active, and vice versa.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We're already starting to see reports from users still
using e1000 where they should be using e1000e now that this is
actually possible. Just to prevent some of this thrash, add
a big warning on load on these devices that people should
switch to e1000e.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add ethtool support to tsi108_eth network driver.
Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Bug fix for tsi108_eth network driver.
This patch fixes a problem with link recovery after connection was lost.
Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Code clean-up for tsi108_eth network driver.
This patch removes not needed dummy read and the corresponding comment.
The PHY logic requires two reads from the status register to get
current link status. This is done correctly inside mii_check_media().
Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Bug fix for tsi108_eth network driver.
This patch fixes a problem with detection of 1000Mb speed.
Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes a use-after-free introduced by
commit a79d8e93d3 and spotted by the
Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix following warnings:
WARNING: drivers/net/sis190.o(.text+0x103): Section mismatch in reference from the function sis190_get_mac_addr() to the function .devinit.text:sis190_get_mac_addr_from_apc()
WARNING: drivers/net/sis190.o(.text+0x10e): Section mismatch in reference from the function sis190_get_mac_addr() to the function .devinit.text:sis190_get_mac_addr_from_eeprom()
Annotate sis190_get_mac_addr() with __devinit.
Signed-off-by: Sergio Luis <sergio@uece.br>
sis190.c | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
New chipsets introduced variant Rx FIFO sizes that need to be taken into
account when setting up the tx pause watermarks. This patch introduces
the new device feature flags based on a version and implements the new
watermarks.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch supports a new fix in hardware regarding tx collisions. In
the cases where we are in autoneg mode and the link partner is in forced
mode, we need to setup the tx deferral register differently in order to
reduce collisions on the wire.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When ARP completes due to a request rather than a reply the neighbor is
marked NUD_STALE instead of reachable (see arp_process()). The handler
for the resulting netevent needs to check also for NUD_STALE.
Failure to use the arp entry can cause RDMA connection failures.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Show whether the MAC address was read from the EEPROM or
the onboard PAR registers.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reading the ID register does not always return the correct ID
from the device, so we retry several times to see if we get
a correct value.
These failures seem to be excaserbated by the speed of the
access to the chip (possibly time between issuing the address
and then the data cycle).
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add entry to handle the MII ioctl() calls via the
generic_mii_ioctl call.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Allow the platform data to specify to the DM9000 driver
that there is no posibility of an attached EEPROM on the
device, so default all reads to 0xff and ignore any
write operations.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The writing of the data should implicitly truncate
the data to 8bits, so do not bother with the ands
in the code.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove the cal_CRC as this is basically wrappering the
ether_crc_le function, and is only being used by the
multicast hash table functions.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The code was using a delay of 8ms, when it should have been
using the EEPROM status flag from the device to indicate the
EEPROM transaction had finished.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use the netif_msg_*() macros to enable the debugging based
on the board's msg_enable field. The output still goes via
the dev_dbg() macros, so will be tagged and output as
appropriate.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We have a perfectly good version control system, so we do not
need to duplicate change comments in the header for this code.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Ensure we hold the spinlock whilst the registers and being
modified even though we hold the overall lock. This should
protect against an interrupt happening whilst we are using
the device.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove the old hack to program an initial EEPROM setting
into the DM9000 as we now have ethtool support for reading
and writing the EEPROM.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Allow the msg_enable value to be read and written by
the ethtool interface.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add ethtool support to access the configuration EEPROM
connected to the DM9000.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add a mutex to serialise access to the chip functions from
entries such as the ethtool and the MII code. This should
reduce the amount of time the spinlock is held to protect
the address register.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The srom array in the board data is only being used in the device probe
routines. The probe also only uses the first 6 bytes of an array
we spend 512ms reading 128 bytes from. Change to reading the
MAC area directly to the MAC address structure.
As a side product, we rename the read_srom_word to dm9000_read_eeprom
to bring it into line with the rest of the driver. No change is made
to the delay in this function, which will be dealt with in a later
patch.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We can use sleeping functions when reading and writing the
PHY registers, so let us sleep instead of busy waiting for
the PHY.
Note, this also fixes a bug reading the PHY where only 100uS
was being used instead of 150uS
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The phy read and write routines call udelay() with the board
lock held, and with the posibility of IRQs being disabled. Since
these delays can be up to 500usec, and are only required as we
have to save the chip's address register.
To improve the behaviour, hold the lock whilst we are writing
and then restore the state before the delay and then repeat
the process once the delay has happened.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove the timer based MII phy polling, as this is
currently broken with the new EEPROM code that now
uses mutexes to protect the phy access.
This will need to be replaced in the future by some
form of mutex safe mechanism for reading the MII
phy status.
The replacement has not been done here as changing
this patch, which is early in the sequence has quite
a knock-on effect. Once this series is merged, then
a new presentation of an patch to poll the MII link
status can be added.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use the flags in the IRQ resource to specify the type of
IRQ being requested, so that systems which do not have
level-based interrupts, or change the interrupt in some
other way can specify this without making an #ifdef mess
in the driver.
This is specifically designed to undo the change in commit
4e4fc05a2b which hardwires the
type for everyone but blackfin to IRQT_RISING, which breaks
all a number of Simtec boards which use (and setup in the
bootloader) active low IRQs.
Note, although there where originally objections due to
the use of IORESOURCE_IRQ and IRQT_ flags not sharing the
same definition, at least <include/linux/interrupt.h> notes
these are the same.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
CC: Daniel Mack <daniel@caiaq.de>
CC: Bryan Wu <bryan.wu@analog.com>
CC: Alex Landau <landau.alex@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Change the debug macros to use the compiler to elide any
unnecessary debug level, and to allow device configurable
debug control.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Move to using dev_dbg() and friends for the output of
information to the user.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Patch from: Laurent Pinchart <laurentp@cse-semaphore.com>
This patch adds a flag to the DM9000 platform data which, when set,
configures the device to use an external PHY.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Ben Dooks <ben-linuy@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Patch from: Laurent Pinchart <laurentp@cse-semaphore.com>
This patch splits the receive status in 8bit wide fields and convert the
packet length from little endian to CPU byte order.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
1. Add common code for stopping queue.
2. No need to call netif_stop_queue followed by netif_wake_queue (and
infact a netif_start_queue could have been used instead), instead
call stop_queue if required, and remove code under USE_GTS macro.
3. There is no need to check for netif_queue_stopped, as the network
core guarantees that for us (I am sure every driver could remove
that check, eg e1000 - I have tested that path a few billion times
with about a few hundred thousand qstops but the condition never
hit even once).
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The e1000 driver stores the content of the PCI resources into
unsigned long's before ioremapping. This breaks on 32 bits
platforms that support 64 bits MMIO resources such as ppc 44x.
This fixes it by removing those temporary variables and passing
directly the result of pci_resource_start/len to ioremap.
The side effect is that I removed the assignments to the netdev
fields mem_start, mem_end and base_addr, which are totally useless
for PCI devices.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
--
drivers/net/e1000/e1000_main.c | 18 +++++-------------
1 file changed, 5 insertions(+), 13 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Acked-by: Dan Williams <dcbw@redhat.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add support for dual network (net_device) interface so that ethernet
and wireless can own separate ethX interfaces.
V2
- Fix the bug that bringing down and up the interface keeps rx
disabled.
- Make 'gelic_net_poll_controller()' extern , as David Woodhouse
pointed out at the previous submission.
- Fix weird usage of member names for the rx descriptor chain
V1
- Export functions which are convenient for both interfaces
- Move irq allocation/release code to driver probe/remove handlers
because interfaces share interrupts.
- Allocate skbs by using dev_alloc_skb() instead of netdev_alloc_skb()
as the interfaces share the hardware rx queue.
- Add gelic_port struct in order to abstract dual interface handling
- Change handlers for hardware queues so that they can handle dual
{source,destination} interfaces.
- Use new NAPI functions
This is a prerequisite for the new PS3 wireless support.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add support for interrupt driven port link status detection.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove some ethtool handlers, which duplicate functionality that was already
provided by the common ethtool handlers.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Code cleanup:
- Use appropriate prefixes for names instead of fixed 'gelic_net'
so that objects of the functions, variables and constants can be estimated.
- Remove definitions for IPSec offload to the gelic hardware. This
functionality is never supported on PS3.
- Group constants with enum.
- Use bitwise constants for interrupt status, instead of bit numbers to
eliminate shift operations.
- Style fixes.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Mark the members of the structure for DMA descriptors with proper endian
annotations and use the appropriate accessor macros.
As the gelic driver works only on PS3, all these macros will be
expanded to null.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The device id for lv1_net_set_interrupt_status_indicator() is wrong.
This path would be invoked only in the case of an initialization failure.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Updates the 8139too driver to work with recently added
(a724605cb7) declared coherent memory
patch for the Dreamcast.
Signed-off-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
To kill the volatiles also switch it to stop poking ISA memory directly
without going through readb and friends.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Change hard coded 2 to NET_IP_ALIGN. Added new #define with comments.
Tested amd_64
Signed-off-by: Don Fry <pcnet32@verizon.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
gcc-3.4.4 on powerpc:
drivers/net/starfire.c:219: error: version causes a section type conflict
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Andrew Morton <akpm@linux-foundation.org>
gcc-3.4.4 on powerpc:
drivers/net/via-velocity.c:443: error: chip_info_table causes a section type conflict
on this one I had to remove the __devinitdata too. Don't know why.
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc-3.4.4 on powerpc:
drivers/net/natsemi.c:245: error: natsemi_pci_info causes a section type conflict
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc-3.4.4 on powerpc:
drivers/net/typhoon.c:137: error: version causes a section type conflict
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/pppol2tp.c: In function `pppol2tp_seq_tunnel_show':
drivers/net/pppol2tp.c:2295: warning: long long unsigned int format, __u64 arg (arg 4)
drivers/net/pppol2tp.c:2295: warning: long long unsigned int format, __u64 arg (arg 5)
drivers/net/pppol2tp.c:2295: warning: long long unsigned int format, __u64 arg (arg 6)
drivers/net/pppol2tp.c:2295: warning: long long unsigned int format, __u64 arg (arg 7)
drivers/net/pppol2tp.c:2295: warning: long long unsigned int format, __u64 arg (arg 8)
drivers/net/pppol2tp.c:2295: warning: long long unsigned int format, __u64 arg (arg 9)
drivers/net/pppol2tp.c: In function `pppol2tp_seq_session_show':
drivers/net/pppol2tp.c:2328: warning: long long unsigned int format, __u64 arg (arg 5)
drivers/net/pppol2tp.c:2328: warning: long long unsigned int format, __u64 arg (arg 6)
drivers/net/pppol2tp.c:2328: warning: long long unsigned int format, __u64 arg (arg 7)
drivers/net/pppol2tp.c:2328: warning: long long unsigned int format, __u64 arg (arg 8)
drivers/net/pppol2tp.c:2328: warning: long long unsigned int format, __u64 arg (arg 9)
drivers/net/pppol2tp.c:2328: warning: long long unsigned int format, __u64 arg (arg 10)
Not all platforms implement u64 with unsigned long long. eg: powerpc.
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc-3.4.4 on powerpc:
drivers/net/bnx2.c:67: error: version causes a section type conflict
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Andrew Morton <akpm@linux-foundation.org>
gcc-3.4.4 on powerpc:
drivers/net/bnx2x.c:73: error: version causes a section type conflict
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/core: Remove unused struct ib_device.flags member
IB/core: Add IP checksum offload support
IPoIB: Add send gather support
IPoIB: Add high DMA feature flag
IB/mlx4: Use multiple WQ blocks to post smaller send WQEs
mlx4_core: Clean up struct mlx4_buf
mlx4_core: For 64-bit systems, vmap() kernel queue buffers
IB/mlx4: Consolidate code to get an entry from a struct mlx4_buf
x25_asy does not take an ldisc reference before calling the flush method.
Fix it to use the helper function we provide.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'cris' of git://www.jni.nu/cris: (158 commits)
CRIS v32: Remove hwregs/timer_defs.h, it is now architecture specific.
CRIS v32: Change drivers/i2c.c locking.
CRIS v32: Rewrite ARTPEC-3 gpio driver to avoid volatiles and general cleanup.
CRIS: Add new timerfd syscall entries.
MAINTAINERS: Add my information for the CRIS port.
CRIS v32: Correct spelling of bandwidth in function name.
CRIS v32: Clean up nandflash.c for ARTPEC-3 and ETRAX FS.
CRIS v10: Cleanup of drivers/gpio.c
CRIS v10: drivers/net/cris/eth_v10.c rename LED defines to CRIS_LED to avoid name clash.
CRIS: Make io_pwm_set_period members unsigned in etraxgpio.h
CRIS: Move ETRAX_AXISFLASHMAP to common Kconfig file.
CRIS: Drop regs parameter from call to profile_tick in kernel/time.c
CRIS v32: Fix minor formatting issue in mach-a3/io.c
CRIS v32: Initialize GIO even if we're rambooting in kernel/head.S
CRIS v32: Remove kernel/arbiter.c, it now exists in machine dependent directory.
CRIS v32: Minor changes to avoid errors in asm-cris/arch-v32/hwregs/reg_rdwr.h
CRIS v32: arch-v32/hwregs/intr_vect_defs.h moved to machine dependent directory.
CRIS v32: Correct offset for TASK_pid in asm-cris/arch-v32/offset.h
CRIS v32: Move register map header to machine dependent directory.
CRIS v32: Let compiler know that memory is clobbered after a break op.
...
Add architecture support for the MN10300/AM33 CPUs produced by MEI to the
kernel.
This patch also adds board support for the ASB2303 with the ASB2308 daughter
board, and the ASB2305. The only processor supported is the MN103E010, which
is an AM33v2 core plus on-chip devices.
[akpm@linux-foundation.org: nuke cvs control strings]
Signed-off-by: Masakazu Urade <urade.masakazu@jp.panasonic.com>
Signed-off-by: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds:
leds: Add HP Jornada 6xx driver
leds: Remove the now uneeded ixp4xx driver
leds: Add power LED to the wrap driver
leds: Fix led-gpio active_low default brightness
leds: hw acceleration for Clevo mail LED driver
leds: Add support for hardware accelerated LED flashing
leds: Standardise LED naming scheme
leds: Add clevo notebook LED driver
As discussed on LKML some notion of 'function' is needed in
LED naming. This patch adds this to the documentation and
standardises existing LED drivers.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Now that struct mlx4_buf.u is a struct instead of a union because of
the vmap() changes, there's no point in having a struct at all. So
move .direct and .page_list directly into struct mlx4_buf and get rid
of a bunch of unnecessary ".u"s.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Since kernel virtual memory is not a problem on 64-bit systems, there
is no reason to use our own 2-layer page mapping scheme for large
kernel queue buffers on such systems. Instead, map the page list to a
single virtually contiguous buffer with vmap(), so that can we access
buffer memory via direct indexing.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
I got the following oops during interface ifup. Unfortunately its not
easily reproducable so I cant say for sure that my fix fixes this
problem, but I am confident and I think its correct anyway:
<2>kernel BUG at /space/kvm/drivers/virtio/virtio_ring.c:234!
<4>illegal operation: 0001 [#1] PREEMPT SMP
<4>Modules linked in:
<4>CPU: 0 Not tainted 2.6.24zlive-guest-07293-gf1ca151-dirty #91
<4>Process swapper (pid: 0, task: 0000000000800938, ksp: 000000000084ddb8)
<4>Krnl PSW : 0404300180000000 0000000000466374 (vring_disable_cb+0x30/0x34)
<4> R:0 T:1 IO:0 EX:0 Key:0 M:1 W:0 P:0 AS:0 CC:3 PM:0 EA:3
<4>Krnl GPRS: 0000000000000001 0000000000000001 0000000010003800 0000000000466344
<4> 000000000e980900 00000000008848b0 000000000084e748 0000000000000000
<4> 000000000087b300 0000000000001237 0000000000001237 000000000f85bdd8
<4> 000000000e980920 00000000001137c0 0000000000464754 000000000f85bdd8
<4>Krnl Code: 0000000000466368: e3b0b0700004 lg %r11,112(%r11)
<4> 000000000046636e: 07fe bcr 15,%r14
<4> 0000000000466370: a7f40001 brc 15,466372
<4> >0000000000466374: a7f4fff6 brc 15,466360
<4> 0000000000466378: eb7ff0500024 stmg %r7,%r15,80(%r15)
<4> 000000000046637e: a7f13e00 tmll %r15,15872
<4> 0000000000466382: b90400ef lgr %r14,%r15
<4> 0000000000466386: a7840001 brc 8,466388
<4>Call Trace:
<4>([<000201500f85c000>] 0x201500f85c000)
<4> [<0000000000466556>] vring_interrupt+0x72/0x88
<4> [<00000000004801a0>] kvm_extint_handler+0x34/0x44
<4> [<000000000010d22c>] do_extint+0xbc/0xf8
<4> [<0000000000113f98>] ext_no_vtime+0x16/0x1a
<4> [<000000000010a182>] cpu_idle+0x216/0x238
<4>([<000000000010a162>] cpu_idle+0x1f6/0x238)
<4> [<0000000000568656>] rest_init+0xaa/0xb8
<4> [<000000000084ee2c>] start_kernel+0x3fc/0x490
<4> [<0000000000100020>] _stext+0x20/0x80
<4>
<4> <0>Kernel panic - not syncing: Fatal exception in interrupt
<4>
After looking at the code and the dump I think the following scenario
happened: Ifup was running on cpu2 and the interrupt arrived on cpu0.
Now virtnet_open on cpu 2 managed to execute napi_enable and disable_cb
but did not execute rx_schedule. Meanwhile on cpu 0 skb_recv_done was
called by vring_interrupt, executed netif_rx_schedule_prep, which
succeeded and therefore called disable_cb. This triggered the BUG_ON,
as interrupts were already disabled by cpu 2.
I think the proper solution is to make the call to disable_cb depend on
the atomic update of NAPI_STATE_SCHED by using netif_rx_schedule_prep
in the same way as skb_recv_done.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The PHY Lib now uses mutexes instead of spin_locks. ucc_geth
and gianfar both grab the locks in their mdio_reset functions,
so they need to use mutex_(un)lock instead. This was not caught
until someone tested it on an SMP system.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Various registers need to be preserved before resetting the device.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The driver needs to ack only the phy status bits that it is currently
handling and preserve the other bits for the other handlers. For
example, when reading/writing from the phy, it should not clear the link
change interrupt bit. This will cause a missing link change interrupt.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes the issue where the transmitter and receiver must be
restarted when applying new changes to certain registers.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Auke Kok