Add support for extended error reporting.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for extended error reporting.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switches and modern SR-IOV enabled NICs may multiplex traffic from Port
representators and control messages over single set of hardware queues.
Control messages and muxed traffic may need ordered delivery.
Those requirements make it hard to comfortably use TC infrastructure today
unless we have a way of attaching metadata to skbs at the upper device.
Because single set of queues is used for many netdevs stopping TC/sched
queues of all of them reliably is impossible and lower device has to
retreat to returning NETDEV_TX_BUSY and usually has to take extra locks on
the fastpath.
This patch attempts to enable port/representative devs to attach metadata
to skbs which carry port id. This way representatives can be queueless and
all queuing can be performed at the lower netdev in the usual way.
Traffic arriving on the port/representative interfaces will be have
metadata attached and will subsequently be queued to the lower device for
transmission. The lower device should recognize the metadata and translate
it to HW specific format which is most likely either a special header
inserted before the network headers or descriptor/metadata fields.
Metadata is associated with the lower device by storing the netdev pointer
along with port id so that if TC decides to redirect or mirror the new
netdev will not try to interpret it.
This is mostly for SR-IOV devices since switches don't have lower netdevs
today.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 31fd85816d ("bpf: permits narrower load from bpf program
context fields") permits narrower load for certain ctx fields.
The commit however will already generate a masking even if
the prog-specific ctx conversion produces the result with
narrower size.
For example, for __sk_buff->protocol, the ctx conversion
loads the data into register with 2-byte load.
A narrower 2-byte load should not generate masking.
For __sk_buff->vlan_present, the conversion function
set the result as either 0 or 1, essentially a byte.
The narrower 2-byte or 1-byte load should not generate masking.
To avoid unnecessary masking, prog-specific *_is_valid_access
now passes converted_op_size back to verifier, which indicates
the valid data width after perceived future conversion.
Based on this information, verifier is able to avoid
unnecessary marking.
Since we want more information back from prog-specific
*_is_valid_access checking, all of them are packed into
one data structure for more clarity.
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the XDP_ATTACHED_* values to include offloaded mode.
Let drivers report whether program is installed in the driver
or the HW by changing the prog_attached field from bool to
u8 (type of the netlink attribute).
Exploit the fact that the value of XDP_ATTACHED_DRV is 1,
therefore since all drivers currently assign the mode with
double negation:
mode = !!xdp_prog;
no drivers have to be modified.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an installation-time flag for requesting that the program
be installed only if it can be offloaded to HW.
Internally new command for ndo_xdp is added, this way we avoid
putting checks into drivers since they all return -EINVAL on
an unknown command.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass XDP flags to the xdp ndo. This will allow drivers to look
at the mode flags and make decisions about offload.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two entries being added at the same time to the IFLA
policy table, whilst parallel bug fixes to decnet
routing dst handling overlapping with the dst gc removal
in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the new getsockopt(2) option SO_PEERGROUPS on SOL_SOCKET to
retrieve the auxiliary groups of the remote peer. It is designed to
naturally extend SO_PEERCRED. That is, the underlying data is from the
same credentials. Regarding its syntax, it is based on SO_PEERSEC. That
is, if the provided buffer is too small, ERANGE is returned and @optlen
is updated. Otherwise, the information is copied, @optlen is set to the
actual size, and 0 is returned.
While SO_PEERCRED (and thus `struct ucred') already returns the primary
group, it lacks the auxiliary group vector. However, nearly all access
controls (including kernel side VFS and SYSVIPC, but also user-space
polkit, DBus, ...) consider the entire set of groups, rather than just
the primary group. But this is currently not possible with pure
SO_PEERCRED. Instead, user-space has to work around this and query the
system database for the auxiliary groups of a UID retrieved via
SO_PEERCRED.
Unfortunately, there is no race-free way to query the auxiliary groups
of the PID/UID retrieved via SO_PEERCRED. Hence, the current user-space
solution is to use getgrouplist(3p), which itself falls back to NSS and
whatever is configured in nsswitch.conf(3). This effectively checks
which groups we *would* assign to the user if it logged in *now*. On
normal systems it is as easy as reading /etc/group, but with NSS it can
resort to quering network databases (eg., LDAP), using IPC or network
communication.
Long story short: Whenever we want to use auxiliary groups for access
checks on IPC, we need further IPC to talk to the user/group databases,
rather than just relying on SO_PEERCRED and the incoming socket. This
is unfortunate, and might even result in dead-locks if the database
query uses the same IPC as the original request.
So far, those recursions / dead-locks have been avoided by using
primitive IPC for all crucial NSS modules. However, we want to avoid
re-inventing the wheel for each NSS module that might be involved in
user/group queries. Hence, we would preferably make DBus (and other IPC
that supports access-management based on groups) work without resorting
to the user/group database. This new SO_PEERGROUPS ioctl would allow us
to make dbus-daemon work without ever calling into NSS.
Cc: Michal Sekletar <msekleta@redhat.com>
Cc: Simon McVittie <simon.mcvittie@collabora.co.uk>
Reviewed-by: Tom Gundersen <teg@jklm.no>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add RTNLGRP_{IPV4,IPV6}_MROUTE_R as two new restricted groups for the
NETLINK_ROUTE family.
Binding to these groups specifically requires CAP_NET_ADMIN to allow
multicast of sensitive messages (e.g. mroute cache reports).
Suggested-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Julien Gomes <julien@arista.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Network interface groups support added while ago, however
there is no IFLA_GROUP attribute description in policy
and netlink message size calculations until now.
Add IFLA_GROUP attribute to the policy.
Fixes: cbda10fa97 ("net_device: add support for network device groups")
Signed-off-by: Serhey Popovych <serhe.popovych@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 217f697436 ("net: busy-poll: allow preemption in
sk_busy_loop()") there is an explicit do_softirq() invocation after
local_bh_enable() has been invoked.
I don't understand why we need this because local_bh_enable() will
invoke do_softirq() once the softirq counter reached zero and we have
softirq-related work pending.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should avoid marking goto rules unresolved when their
target is actually reachable after rule deletion.
Consolder following sample scenario:
# ip -4 ru sh
0: from all lookup local
32000: from all goto 32100
32100: from all lookup main
32100: from all lookup default
32766: from all lookup main
32767: from all lookup default
# ip -4 ru del pref 32100 table main
# ip -4 ru sh
0: from all lookup local
32000: from all goto 32100 [unresolved]
32100: from all lookup default
32766: from all lookup main
32767: from all lookup default
After removal of first rule with preference 32100 we
mark all goto rules as unreachable, even when rule with
same preference as removed one still present.
Check if next rule with same preference is available
and make all rules with goto action pointing to it.
Signed-off-by: Serhey Popovych <serhe.popovych@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename:
wait_queue_t => wait_queue_entry_t
'wait_queue_t' was always a slight misnomer: its name implies that it's a "queue",
but in reality it's a queue *entry*. The 'real' queue is the wait queue head,
which had to carry the name.
Start sorting this out by renaming it to 'wait_queue_entry_t'.
This also allows the real structure name 'struct __wait_queue' to
lose its double underscore and become 'struct wait_queue_entry',
which is the more canonical nomenclature for such data types.
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Using get_random_u32 here is faster, more fitting of the use case, and
just as cryptographically secure. It also has the benefit of providing
better randomness at early boot, which is when many of these structures
are assigned.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Quoting Joe Stringer:
If a user loads nf_conntrack_ftp, sends FTP traffic through a network
namespace, destroys that namespace then unloads the FTP helper module,
then the kernel will crash.
Events that lead to the crash:
1. conntrack is created with ftp helper in netns x
2. This netns is destroyed
3. netns destruction is scheduled
4. netns destruction wq starts, removes netns from global list
5. ftp helper is unloaded, which resets all helpers of the conntracks
via for_each_net()
but because netns is already gone from list the for_each_net() loop
doesn't include it, therefore all of these conntracks are unaffected.
6. helper module unload finishes
7. netns wq invokes destructor for rmmod'ed helper
CC: "Eric W. Biederman" <ebiederm@xmission.com>
Reported-by: Joe Stringer <joe@ovn.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
DST_NOCACHE flag check has been removed from dst_release() and
dst_hold_safe() in a previous patch because all the dst are now ref
counted properly and can be released based on refcnt only.
Looking at the rest of the DST_NOCACHE use, all of them can now be
removed or replaced with other checks.
So this patch gets rid of all the DST_NOCACHE usage and remove this flag
completely.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all the components have been changed to release dst based on
refcnt only and not depend on dst gc anymore, we can remove the
temporary flag DST_NOGC.
Note that we also need to remove the DST_NOCACHE check in dst_release()
and dst_hold_safe() because now all the dst are released based on refcnt
and behaves as DST_NOCACHE.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes all dst gc related code and all the dst free
functions
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the creation of xfrm_dst bundle, always take ref count when
allocating the dst. This way, xfrm_bundle_create() will form a linked
list of dst with dst->child pointing to a ref counted dst child. And
the returned dst pointer is also ref counted. This makes the link from
the flow cache to this dst now ref counted properly.
As the dst is always ref counted properly, we can safely mark
DST_NOGC flag so dst_release() will release dst based on refcnt only.
And dst gc is no longer needed and all dst_free() and its related
function calls should be replaced with dst_release() or
dst_release_immediate().
The special handling logic for dst->child in dst_destroy() can be
replaced with a simple dst_release_immediate() call on the child to
release the whole list linked by dst->child pointer.
Previously used DST_NOHASH flag is not needed anymore as well. The
reason that DST_NOHASH is used in the existing code is mainly to prevent
the dst inserted in the fib tree to be wrongly destroyed during the
deletion of the xfrm_dst bundle. So in the existing code, DST_NOHASH
flag is marked in all the dst children except the one which is in the
fib tree.
However, with this patch series to remove dst gc logic and release dst
only based on ref count, it is safe to release all the children from a
xfrm_dst bundle as long as the dst children are all ref counted
properly which is already the case in the existing code.
So, this patch removes the use of DST_NOHASH flag.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function should be called when removing routes from fib tree after
the dst gc is no longer in use.
We first mark DST_OBSOLETE_DEAD on this dst to make sure next
dst_ops->check() fails and returns NULL.
Secondly, as we no longer keep the gc_list, we need to properly
release dst->dev right at the moment when the dst is removed from
the fib/fib6 tree.
It does the following:
1. change dst->input and output pointers to dst_discard/dst_dscard_out to
discard all packets
2. replace dst->dev with loopback interface
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current mechanism of freeing dst is a bit complicated. dst has its
ref count and when user grabs the reference to the dst, the ref count is
properly taken in most cases except in IPv4/IPv6/decnet/xfrm routing
code due to some historic reasons.
If the reference to dst is always taken properly, we should be able to
simplify the logic in dst_release() to destroy dst when dst->__refcnt
drops from 1 to 0. And this should be the only condition to determine
if we can call dst_destroy().
And as dst is always ref counted, there is no need for a dst garbage
list to hold the dst entries that already get removed by the routing
code but are still held by other users. And the task to periodically
check the list to free dst if ref count become 0 is also not needed
anymore.
This patch introduces a temporary flag DST_NOGC(no garbage collector).
If it is set in the dst, dst_release() will call dst_destroy() when
dst->__refcnt drops to 0. dst_hold_safe() will also check for this flag
and do atomic_inc_not_zero() similar as DST_NOCACHE to avoid double free
issue.
This temporary flag is mainly used so that we can make the transition
component by component without breaking other parts.
This flag will be removed after all components are properly transitioned.
This patch also introduces a new function dst_release_immediate() which
destroys dst without waiting on the rcu when refcnt drops to 0. It will
be used in later patches.
Follow-up patches will correct all the places to properly take ref count
on dst and mark DST_NOGC. dst_release() or dst_release_immediate() will
be used to release the dst instead of dst_free() and its related
functions.
And final clean-up patch will remove the DST_NOGC flag.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose prog_id through IFLA_XDP_PROG_ID. This patch
makes modification to generic_xdp. The later patches will
modify other xdp-supported drivers.
prog_id is added to struct net_dev_xdp.
iproute2 patch will be followed. Here is how the 'ip link'
will look like:
> ip link show eth0
3: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 xdp(prog_id:1) qdisc fq_codel state UP mode DEFAULT group default qlen 1000
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Alexei Starovoitov <ast@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions return void * and remove all the casts across
the tree, adding a (u8 *) cast only where the unsigned char pointer
was used directly, all done with the following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
@@
expression SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- fn(SKB, LEN)[0]
+ *(u8 *)fn(SKB, LEN)
Note that the last part there converts from push(...)[0] to the
more idiomatic *(u8 *)push(...).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions return void * and remove all the casts across
the tree, adding a (u8 *) cast only where the unsigned char pointer
was used directly, all done with the following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = {
skb_pull,
__skb_pull,
skb_pull_inline,
__pskb_pull_tail,
__pskb_pull,
pskb_pull
};
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = {
skb_pull,
__skb_pull,
skb_pull_inline,
__pskb_pull_tail,
__pskb_pull,
pskb_pull
};
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions (skb_put, __skb_put and pskb_put) return void *
and remove all the casts across the tree, adding a (u8 *) cast only
where the unsigned char pointer was used directly, all done with the
following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_put, __skb_put };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_put, __skb_put };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
which actually doesn't cover pskb_put since there are only three
users overall.
A handful of stragglers were converted manually, notably a macro in
drivers/isdn/i4l/isdn_bsdcomp.c and, oddly enough, one of the many
instances in net/bluetooth/hci_sock.c. In the former file, I also
had to fix one whitespace problem spatch introduced.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were many places that my previous spatch didn't find,
as pointed out by yuan linyu in various patches.
The following spatch found many more and also removes the
now unnecessary casts:
@@
identifier p, p2;
expression len;
expression skb;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_zero(skb, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_zero(skb, len);
)
... when != p
(
p2 = (t2)p;
-memset(p2, 0, len);
|
-memset(p, 0, len);
)
@@
type t, t2;
identifier p, p2;
expression skb;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_zero(skb, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_zero(skb, sizeof(t));
)
... when != p
(
p2 = (t2)p;
-memset(p2, 0, sizeof(*p));
|
-memset(p, 0, sizeof(*p));
)
@@
expression skb, len;
@@
-memset(skb_put(skb, len), 0, len);
+skb_put_zero(skb, len);
Apply it to the tree (with one manual fixup to keep the
comment in vxlan.c, which spatch removed.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 83ada39bb79d ("net: factor out a helper to decrement the
skb refcount") provided and used a helper for decrementing skb usage,
but I missed at least a spot for it.
This change remove some more duplicated code reusing skb_unref() in
napi_consume_skb(), too. The helper uses an additional, unneeded
unlikely(!skb) test - napi_consume_skb() already check it a few lines
above - but the compiler is smart enough to optimize the duplicated
test out.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, verifier will reject a program if it contains an
narrower load from the bpf context structure. For example,
__u8 h = __sk_buff->hash, or
__u16 p = __sk_buff->protocol
__u32 sample_period = bpf_perf_event_data->sample_period
which are narrower loads of 4-byte or 8-byte field.
This patch solves the issue by:
. Introduce a new parameter ctx_field_size to carry the
field size of narrower load from prog type
specific *__is_valid_access validator back to verifier.
. The non-zero ctx_field_size for a memory access indicates
(1). underlying prog type specific convert_ctx_accesses
supporting non-whole-field access
(2). the current insn is a narrower or whole field access.
. In verifier, for such loads where load memory size is
less than ctx_field_size, verifier transforms it
to a full field load followed by proper masking.
. Currently, __sk_buff and bpf_perf_event_data->sample_period
are supporting narrowing loads.
. Narrower stores are still not allowed as typical ctx stores
are just normal stores.
Because of this change, some tests in verifier will fail and
these tests are removed. As a bonus, rename some out of bound
__sk_buff->cb access to proper field name and remove two
redundant "skb cb oob" tests.
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unfortunately, struct iwreq isn't a proper subset of struct ifreq,
but is still handled by the same code path. Robert reported that
then applications may (randomly) fault if the struct iwreq they
pass happens to land within 8 bytes of the end of a mapping (the
struct is only 32 bytes, vs. struct ifreq's 40 bytes).
To fix this, pull out the code handling wireless extension ioctls
and copy only the smaller structure in this case.
This bug goes back a long time, I tracked that it was introduced
into mainline in 2.1.15, over 20 years ago!
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=195869
Reported-by: Robert O'Callahan <robert@ocallahan.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch fixes uninitialized symbol warning that
got introduced by the following commit
773fc8f6e8 ("net: rps: send out pending IPI's on CPU hotplug")
Signed-off-by: Ashwanth Goli <ashwanth@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since UDP no more uses sk->destructor, we can clear completely
the skb head state before enqueuing. Amend and use
skb_release_head_state() for that.
All head states share a single cacheline, which is not
normally used/accesses on dequeue. We can avoid entirely accessing
such cacheline implementing and using in the UDP code a specialized
skb free helper which ignores the skb head state.
This saves a cacheline miss at skb deallocation time.
v1 -> v2:
replaced secpath_reset() with skb_release_head_state()
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same code is replicated in 3 different places; move it to a
common helper.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow for tc BPF programs to set a skb->hash, apart from clearing
and triggering a recalc that we have right now. It allows for BPF
to implement a custom hashing routine for skb_get_hash().
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since cg_skb_func_proto() doesn't do anything else than just calling
into sk_filter_func_proto(), remove it and set sk_filter_func_proto()
directly for .get_func_proto callback.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the user tries to assign a specific nsid, idr_alloc() is called with
the range [nsid, nsid+1]. If this nsid is already used, idr_alloc() returns
ENOSPC (No space left on device). In our case, it's better to return
EEXIST to make it clear that the nsid is not available.
CC: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It helps the user to identify errors.
CC: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPI's from the victim cpu are not handled in dev_cpu_callback.
So these pending IPI's would be sent to the remote cpu only when
NET_RX is scheduled on the victim cpu and since this trigger is
unpredictable it would result in packet latencies on the remote cpu.
This patch add support to send the pending ipi's of victim cpu.
Signed-off-by: Ashwanth Goli <ashwanth@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It looks like this:
Message from syslogd@flamingo at Apr 26 00:45:00 ...
kernel:unregister_netdevice: waiting for lo to become free. Usage count = 4
They seem to coincide with net namespace teardown.
The message is emitted by netdev_wait_allrefs().
Forced a kdump in netdev_run_todo, but found that the refcount on the lo
device was already 0 at the time we got to the panic.
Used bcc to check the blocking in netdev_run_todo. The only places
where we're off cpu there are in the rcu_barrier() and msleep() calls.
That behavior is expected. The msleep time coincides with the amount of
time we spend waiting for the refcount to reach zero; the rcu_barrier()
wait times are not excessive.
After looking through the list of callbacks that the netdevice notifiers
invoke in this path, it appears that the dst_dev_event is the most
interesting. The dst_ifdown path places a hold on the loopback_dev as
part of releasing the dev associated with the original dst cache entry.
Most of our notifier callbacks are straight-forward, but this one a)
looks complex, and b) places a hold on the network interface in
question.
I constructed a new bcc script that watches various events in the
liftime of a dst cache entry. Note that dst_ifdown will take a hold on
the loopback device until the invalidated dst entry gets freed.
[ __dst_free] on DST: ffff883ccabb7900 IF tap1008300eth0 invoked at 1282115677036183
__dst_free
rcu_nocb_kthread
kthread
ret_from_fork
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When inheriting tx_flags from one skbuff to another, always apply a
mask to avoid overwriting unrelated other bits in the field.
The two SKBTX_SHARED_FRAG cases clears all other bits. In practice,
tx_flags are zero at this point now. But this is fragile. Timestamp
flags are set, for instance, if in tcp_gso_segment, after this clear
in skb_segment.
The SKBTX_ANY_TSTAMP mask in __skb_tstamp_tx ensures that new
skbs do not accidentally inherit flags such as SKBTX_SHARED_FRAG.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DRAM supply shortage and poor memory pressure tracking in TCP
stack makes any change in SO_SNDBUF/SO_RCVBUF (or equivalent autotuning
limits) and tcp_mem[] quite hazardous.
TCPMemoryPressures SNMP counter is an indication of tcp_mem sysctl
limits being hit, but only tracking number of transitions.
If TCP stack behavior under stress was perfect :
1) It would maintain memory usage close to the limit.
2) Memory pressure state would be entered for short times.
We certainly prefer 100 events lasting 10ms compared to one event
lasting 200 seconds.
This patch adds a new SNMP counter tracking cumulative duration of
memory pressure events, given in ms units.
$ cat /proc/sys/net/ipv4/tcp_mem
3088 4117 6176
$ grep TCP /proc/net/sockstat
TCP: inuse 180 orphan 0 tw 2 alloc 234 mem 4140
$ nstat -n ; sleep 10 ; nstat |grep Pressure
TcpExtTCPMemoryPressures 1700
TcpExtTCPMemoryPressuresChrono 5209
v2: Used EXPORT_SYMBOL_GPL() instead of EXPORT_SYMBOL() as David
instructed.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the structure's fields are not initialized by the
rtnetlink. If driver doesn't set those in ndo_get_vf_config(),
they'd leak memory to user.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
CC: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Greg Rose <gvrose8192@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Network devices can allocate reasources and private memory using
netdev_ops->ndo_init(). However, the release of these resources
can occur in one of two different places.
Either netdev_ops->ndo_uninit() or netdev->destructor().
The decision of which operation frees the resources depends upon
whether it is necessary for all netdev refs to be released before it
is safe to perform the freeing.
netdev_ops->ndo_uninit() presumably can occur right after the
NETDEV_UNREGISTER notifier completes and the unicast and multicast
address lists are flushed.
netdev->destructor(), on the other hand, does not run until the
netdev references all go away.
Further complicating the situation is that netdev->destructor()
almost universally does also a free_netdev().
This creates a problem for the logic in register_netdevice().
Because all callers of register_netdevice() manage the freeing
of the netdev, and invoke free_netdev(dev) if register_netdevice()
fails.
If netdev_ops->ndo_init() succeeds, but something else fails inside
of register_netdevice(), it does call ndo_ops->ndo_uninit(). But
it is not able to invoke netdev->destructor().
This is because netdev->destructor() will do a free_netdev() and
then the caller of register_netdevice() will do the same.
However, this means that the resources that would normally be released
by netdev->destructor() will not be.
Over the years drivers have added local hacks to deal with this, by
invoking their destructor parts by hand when register_netdevice()
fails.
Many drivers do not try to deal with this, and instead we have leaks.
Let's close this hole by formalizing the distinction between what
private things need to be freed up by netdev->destructor() and whether
the driver needs unregister_netdevice() to perform the free_netdev().
netdev->priv_destructor() performs all actions to free up the private
resources that used to be freed by netdev->destructor(), except for
free_netdev().
netdev->needs_free_netdev is a boolean that indicates whether
free_netdev() should be done at the end of unregister_netdevice().
Now, register_netdevice() can sanely release all resources after
ndo_ops->ndo_init() succeeds, by invoking both ndo_ops->ndo_uninit()
and netdev->priv_destructor().
And at the end of unregister_netdevice(), we invoke
netdev->priv_destructor() and optionally call free_netdev().
Signed-off-by: David S. Miller <davem@davemloft.net>
KMSAN reported a use of uninitialized memory in dev_set_alias(),
which was caused by calling strlcpy() (which in turn called strlen())
on the user-supplied non-terminated string.
Signed-off-by: Alexander Potapenko <glider@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is need to instruct the HW offloaded path to push certain matched
packets to cpu/kernel for further analysis. So this patch introduces a
new TRAP control action to TC.
For kernel datapath, this action does not make much sense. So with the
same logic as in HW, new TRAP behaves similar to STOLEN. The skb is just
dropped in the datapath (and virtually ejected to an upper level, which
does not exist in case of kernel).
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We must free allocated skb when genlmsg_put() return fails.
Fixes: 1555d204e7 ("devlink: Support for pipeline debug (dpipe)")
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a defense-in-depth measure in response to bugs like
4d6fa57b4d ("macsec: avoid heap overflow in skb_to_sgvec"). There's
not only a potential overflow of sglist items, but also a stack overflow
potential, so we fix this by limiting the amount of recursion this function
is allowed to do. Not actually providing a bounded base case is a future
disaster that we can easily avoid here.
As a small matter of house keeping, we take this opportunity to move the
documentation comment over the actual function the documentation is for.
While this could be implemented by using an explicit stack of skbuffs,
when implementing this, the function complexity increased considerably,
and I don't think such complexity and bloat is actually worth it. So,
instead I built this and tested it on x86, x86_64, ARM, ARM64, and MIPS,
and measured the stack usage there. I also reverted the recent MIPS
changes that give it a separate IRQ stack, so that I could experience
some worst-case situations. I found that limiting it to 24 layers deep
yielded a good stack usage with room for safety, as well as being much
deeper than any driver actually ever creates.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: David Howells <dhowells@redhat.com>
Cc: Sabrina Dubroca <sd@queasysnail.net>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The command
# arp -s 62.2.0.1 a🅱️c:d:e:f dev eth2
adds an entry like the following (listed by "arp -an")
? (62.2.0.1) at 0a:0b:0c:0d:0e:0f [ether] PERM on eth2
but the symmetric deletion command
# arp -i eth2 -d 62.2.0.1
does not remove the PERM entry from the table, and instead leaves behind
? (62.2.0.1) at <incomplete> on eth2
The reason is that there is a refcnt of 1 for the arp_tbl itself
(neigh_alloc starts off the entry with a refcnt of 1), thus
the neigh_release() call from arp_invalidate() will (at best) just
decrement the ref to 1, but will never actually free it from the
table.
To fix this, we need to do something like neigh_forced_gc: if
the refcnt is 1 (i.e., on the table's ref), remove the entry from
the table and free it. This patch refactors and shares common code
between neigh_forced_gc and the newly added neigh_remove_one.
A similar issue exists for IPv6 Neighbor Cache entries, and is fixed
in a similar manner by this patch.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to f5f99309fa (sock: do not set sk_err in
sock_dequeue_err_skb), sk_err was reset to the error of
the skb on the head of the error queue.
Applications, most notably ping, are relying on this
behavior to reset sk_err for ICMP packets.
Set sk_err to the ICMP error when there is an ICMP packet
at the head of the error queue.
Fixes: f5f99309fa (sock: do not set sk_err in sock_dequeue_err_skb)
Reported-by: Cyril Hrubis <chrubis@suse.cz>
Tested-by: Cyril Hrubis <chrubis@suse.cz>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Save a bit of code by using the kernel extension.
$ size net/core/net-procfs.o*
text data bss dec hex filename
3701 120 0 3821 eed net/core/net-procfs.o.new
3764 120 0 3884 f2c net/core/net-procfs.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for dissection of ip tos and ttl and ipv6 traffic-class
and hoplimit. Both are dissected into the same struct.
Uses similar call to ip dissection function as with tcp, arp and others.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To track stack depth of classic bpf programs we only need
to analyze ST|STX instructions, since check_load_and_stores()
verifies that programs can load from stack only after write.
We also need to change the way cBPF stack slots map to eBPF stack,
since typical classic programs are using slots 0 and 1, so they
need to map to stack offsets -4 and -8 respectively in order
to take advantage of small stack interpreter and JITs.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Small clean-up to rtmsg_ifinfo() to use the rtnl_get_event()
interface instead of using 'internal' values directly.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass extack arg down to lwtunnel_build_state and the build_state callbacks.
Add messages for failures in lwtunnel_build_state, and add the extarg to
nla_parse where possible in the build_state callbacks.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass extack down to lwtunnel_valid_encap_type and
lwtunnel_valid_encap_type_attr. Add messages for unknown
or unsupported encap types.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When netdev events happen, a rtnetlink_event() handler will send
messages for every event in it's white list. These messages contain
current information about a particular device, but they do not include
the iformation about which event just happened. So, it is impossible
to tell what just happend for these events.
This patch adds a new extension to RTM_NEWLINK message called IFLA_EVENT
that would have an encoding of event that triggered this
message. This would allow the the message consumer to easily determine
if it needs to perform certain actions.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Overlapping changes in drivers/net/phy/marvell.c, bug fix in 'net'
restricting a HW workaround alongside cleanups in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrey Konovalov reported crashes in ipv4_mtu()
I could reproduce the issue with KASAN kernels, between
10.246.7.151 and 10.246.7.152 :
1) 20 concurrent netperf -t TCP_RR -H 10.246.7.152 -l 1000 &
2) At the same time run following loop :
while :
do
ip ro add 10.246.7.152 dev eth0 src 10.246.7.151 mtu 1500
ip ro del 10.246.7.152 dev eth0 src 10.246.7.151 mtu 1500
done
Cong Wang attempted to add back rt->fi in commit
82486aa6f1 ("ipv4: restore rt->fi for reference counting")
but this proved to add some issues that were complex to solve.
Instead, I suggested to add a refcount to the metrics themselves,
being a standalone object (in particular, no reference to other objects)
I tried to make this patch as small as possible to ease its backport,
instead of being super clean. Note that we believe that only ipv4 dst
need to take care of the metric refcount. But if this is wrong,
this patch adds the basic infrastructure to extend this to other
families.
Many thanks to Julian Anastasov for reviewing this patch, and Cong Wang
for his efforts on this problem.
Fixes: 2860583fe8 ("ipv4: Kill rt->fi")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bpf_clone_redirect() still needs to be listed in
bpf_helper_changes_pkt_data() since we call into
bpf_try_make_head_writable() from there, thus we need
to invalidate prior pkt regs as well.
Fixes: 36bbef52c7 ("bpf: direct packet write and access for helpers for clsact progs")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The default value for somaxconn is set in sysctl_core_net_init(), but this
function is not called when kernel is configured without CONFIG_SYSCTL.
This results in the kernel not being able to accept TCP connections,
because the backlog has zero size. Usually, the user ends up with:
"TCP: request_sock_TCP: Possible SYN flooding on port 7. Dropping request. Check SNMP counters."
If SYN cookies are not enabled the connection is rejected.
Before ef547f2ac1 (tcp: remove max_qlen_log), the effects were less
severe, because the backlog was always at least eight slots long.
Signed-off-by: Roman Kapl <roman.kapl@sysgo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for dissection of tcp flags. Uses similar function call to
tcp dissection function as arp, mpls and others.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add SOF_TIMESTAMPING_OPT_TX_SWHW option to allow an outgoing packet to
be looped to the socket's error queue with a software timestamp even
when a hardware transmit timestamp is expected to be provided by the
driver.
Applications using this option will receive two separate messages from
the error queue, one with a software timestamp and the other with a
hardware timestamp. As the hardware timestamp is saved to the shared skb
info, which may happen before the first message with software timestamp
is received by the application, the hardware timestamp is copied to the
SCM_TIMESTAMPING control message only when the skb has no software
timestamp or it is an incoming packet.
While changing sw_tx_timestamp(), inline it in skb_tx_timestamp() as
there are no other users.
CC: Richard Cochran <richardcochran@gmail.com>
CC: Willem de Bruijn <willemb@google.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit b68581778c ("net: Make skb->skb_iif always track
skb->dev") skbs don't have the original index of the interface which
received the packet. This information is now needed for a new control
message related to hardware timestamping.
Instead of adding a new field to skb, we can find the device by the NAPI
ID if it is available, i.e. CONFIG_NET_RX_BUSY_POLL is enabled and the
driver is using NAPI. Add dev_get_by_napi_id() and also skb_napi_id() to
hide the CONFIG_NET_RX_BUSY_POLL ifdef.
CC: Richard Cochran <richardcochran@gmail.com>
Suggested-by: Willem de Bruijn <willemb@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include HWTSTAMP_FILTER_NTP_ALL in net_hwtstamp_validate() as a valid
filter and update drivers which can timestamp all packets, or which
explicitly list unsupported filters instead of using a default case, to
handle the filter.
CC: Richard Cochran <richardcochran@gmail.com>
CC: Willem de Bruijn <willemb@google.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add HWTSTAMP_FILTER_NTP_ALL to the hwtstamp_rx_filters enum for
timestamping of NTP packets. There is currently only one driver
(phyter) that could support it directly.
CC: Richard Cochran <richardcochran@gmail.com>
CC: Willem de Bruijn <willemb@google.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_csum_hwoffload_help() uses netdev features and skb->csum_not_inet to
determine if skb needs software computation of Internet Checksum or crc32c
(or nothing, if this computation can be done by the hardware). Use it in
place of skb_checksum_help() in validate_xmit_skb() to avoid corruption
of non-GSO SCTP packets having skb->ip_summed equal to CHECKSUM_PARTIAL.
While at it, remove references to skb_csum_off_chk* functions, since they
are not present anymore in Linux _ see commit cf53b1da73 ("Revert
"net: Add driver helper functions to determine checksum offloadability"").
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->csum_not_inet carries the indication on which algorithm is needed to
compute checksum on skb in the transmit path, when skb->ip_summed is equal
to CHECKSUM_PARTIAL. If skb carries a SCTP packet and crc32c hasn't been
yet written in L4 header, skb->csum_not_inet is assigned to 1; otherwise,
assume Internet Checksum is needed and thus set skb->csum_not_inet to 0.
Suggested-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This bit was introduced with commit 5a21232983 ("net: Support for
csum_bad in skbuff") to reduce the stack workload when processing RX
packets carrying a wrong Internet Checksum. Up to now, only one driver and
GRO core are setting it.
Suggested-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_crc32c_csum_help is like skb_checksum_help, but it is designed for
checksumming SCTP packets using crc32c (see RFC3309), provided that
libcrc32c.ko has been loaded before. In case libcrc32c is not loaded,
invoking skb_crc32c_csum_help on a skb results in one the following
printouts:
warn_crc32c_csum_update: attempt to compute crc32c without libcrc32c.ko
warn_crc32c_csum_combine: attempt to compute crc32c without libcrc32c.ko
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp_compute_checksum requires crc32c symbol (provided by libcrc32c), so
it can't be used in net core. Like it has been done previously with other
symbols (e.g. ipv6_dst_lookup), introduce a stub struct skb_checksum_ops
to allow computation of crc32c checksum in net core after sctp.ko (and thus
libcrc32c) has been loaded.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mauro says:
This patch series convert the remaining DocBooks to ReST.
The first version was originally
send as 3 patch series:
[PATCH 00/36] Convert DocBook documents to ReST
[PATCH 0/5] Convert more books to ReST
[PATCH 00/13] Get rid of DocBook
The lsm book was added as if it were a text file under
Documentation. The plan is to merge it with another file
under Documentation/security, after both this series and
a security Documentation patch series gets merged.
It also adjusts some Sphinx-pedantic errors/warnings on
some kernel-doc markups.
I also added some patches here to add PDF output for all
existing ReST books.
This function has to return NULL on a error case, because there is a
separate error variable.
The offset has to be changed only if skb is returned
v2: fix udp code to not use an extra variable
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: David S. Miller <davem@davemloft.net>
Fixes: 65101aeca5 ("net/sock: factor out dequeue/peek with offset cod")
Signed-off-by: Andrei Vagin <avagin@openvz.org>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move tc_classify function to cls_api.c where it belongs, rename it to
fit the namespace.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_INET is not set, net/core/sock.c can not compile :
net/core/sock.c: In function ‘skb_orphan_partial’:
net/core/sock.c:1810:2: error: implicit declaration of function
‘skb_is_tcp_pure_ack’ [-Werror=implicit-function-declaration]
if (skb_is_tcp_pure_ack(skb))
^
Fix this by always including <net/tcp.h>
Fixes: f6ba8d33cf ("netem: fix skb_orphan_partial()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's a common practice to send gratuitous ARPs after moving an
IP address to another device to speed up healing of a service. To
fulfill service availability constraints, the timing of network peers
updating their caches to point to a new location of an IP address can be
particularly important.
Sometimes neigh_update calls won't touch neither lladdr nor state, for
example if an update arrives in locktime interval. The neigh->updated
value is tested by the protocol specific neigh code, which in turn
will influence whether NEIGH_UPDATE_F_OVERRIDE gets set in the
call to neigh_update() or not. As a result, we may effectively ignore
the update request, bailing out of touching the neigh entry, except that
we still bump its timestamps inside neigh_update.
This may be a problem for updates arriving in quick succession. For
example, consider the following scenario:
A service is moved to another device with its IP address. The new device
sends three gratuitous ARP requests into the network with ~1 seconds
interval between them. Just before the first request arrives to one of
network peer nodes, its neigh entry for the IP address transitions from
STALE to DELAY. This transition, among other things, updates
neigh->updated. Once the kernel receives the first gratuitous ARP, it
ignores it because its arrival time is inside the locktime interval. The
kernel still bumps neigh->updated. Then the second gratuitous ARP
request arrives, and it's also ignored because it's still in the (new)
locktime interval. Same happens for the third request. The node
eventually heals itself (after delay_first_probe_time seconds since the
initial transition to DELAY state), but it just wasted some time and
require a new ARP request/reply round trip. This unfortunate behaviour
both puts more load on the network, as well as reduces service
availability.
This patch changes neigh_update so that it bumps neigh->updated (as well
as neigh->confirmed) only once we are sure that either lladdr or entry
state will change). In the scenario described above, it means that the
second gratuitous ARP request will actually update the entry lladdr.
Ideally, we would update the neigh entry on the very first gratuitous
ARP request. The locktime mechanism is designed to ignore ARP updates in
a short timeframe after a previous ARP update was honoured by the kernel
layer. This would require tracking timestamps for state transitions
separately from timestamps when actual updates are received. This would
probably involve changes in neighbour struct. Therefore, the patch
doesn't tackle the issue of the first gratuitous APR ignored, leaving
it for a follow-up.
Signed-off-by: Ihar Hrachyshka <ihrachys@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BBR congestion control depends on pacing, and pacing is
currently handled by sch_fq packet scheduler for performance reasons,
and also because implemening pacing with FQ was convenient to truly
avoid bursts.
However there are many cases where this packet scheduler constraint
is not practical.
- Many linux hosts are not focusing on handling thousands of TCP
flows in the most efficient way.
- Some routers use fq_codel or other AQM, but still would like
to use BBR for the few TCP flows they initiate/terminate.
This patch implements an automatic fallback to internal pacing.
Pacing is requested either by BBR or use of SO_MAX_PACING_RATE option.
If sch_fq happens to be in the egress path, pacing is delegated to
the qdisc, otherwise pacing is done by TCP itself.
One advantage of pacing from TCP stack is to get more precise rtt
estimations, and less work done from TX completion, since TCP Small
queue limits are not generally hit. Setups with single TX queue but
many cpus might even benefit from this.
Note that unlike sch_fq, we do not take into account header sizes.
Taking care of these headers would add additional complexity for
no practical differences in behavior.
Some performance numbers using 800 TCP_STREAM flows rate limited to
~48 Mbit per second on 40Gbit NIC.
If MQ+pfifo_fast is used on the NIC :
$ sar -n DEV 1 5 | grep eth
14:48:44 eth0 725743.00 2932134.00 46776.76 4335184.68 0.00 0.00 1.00
14:48:45 eth0 725349.00 2932112.00 46751.86 4335158.90 0.00 0.00 0.00
14:48:46 eth0 725101.00 2931153.00 46735.07 4333748.63 0.00 0.00 0.00
14:48:47 eth0 725099.00 2931161.00 46735.11 4333760.44 0.00 0.00 1.00
14:48:48 eth0 725160.00 2931731.00 46738.88 4334606.07 0.00 0.00 0.00
Average: eth0 725290.40 2931658.20 46747.54 4334491.74 0.00 0.00 0.40
$ vmstat 1 5
procs -----------memory---------- ---swap-- -----io---- -system-- ------cpu-----
r b swpd free buff cache si so bi bo in cs us sy id wa st
4 0 0 259825920 45644 2708324 0 0 21 2 247 98 0 0 100 0 0
4 0 0 259823744 45644 2708356 0 0 0 0 2400825 159843 0 19 81 0 0
0 0 0 259824208 45644 2708072 0 0 0 0 2407351 159929 0 19 81 0 0
1 0 0 259824592 45644 2708128 0 0 0 0 2405183 160386 0 19 80 0 0
1 0 0 259824272 45644 2707868 0 0 0 32 2396361 158037 0 19 81 0 0
Now use MQ+FQ :
lpaa23:~# echo fq >/proc/sys/net/core/default_qdisc
lpaa23:~# tc qdisc replace dev eth0 root mq
$ sar -n DEV 1 5 | grep eth
14:49:57 eth0 678614.00 2727930.00 43739.13 4033279.14 0.00 0.00 0.00
14:49:58 eth0 677620.00 2723971.00 43674.69 4027429.62 0.00 0.00 1.00
14:49:59 eth0 676396.00 2719050.00 43596.83 4020125.02 0.00 0.00 0.00
14:50:00 eth0 675197.00 2714173.00 43518.62 4012938.90 0.00 0.00 1.00
14:50:01 eth0 676388.00 2719063.00 43595.47 4020171.64 0.00 0.00 0.00
Average: eth0 676843.00 2720837.40 43624.95 4022788.86 0.00 0.00 0.40
$ vmstat 1 5
procs -----------memory---------- ---swap-- -----io---- -system-- ------cpu-----
r b swpd free buff cache si so bi bo in cs us sy id wa st
2 0 0 259832240 46008 2710912 0 0 21 2 223 192 0 1 99 0 0
1 0 0 259832896 46008 2710744 0 0 0 0 1702206 198078 0 17 82 0 0
0 0 0 259830272 46008 2710596 0 0 0 0 1696340 197756 1 17 83 0 0
4 0 0 259829168 46024 2710584 0 0 16 0 1688472 197158 1 17 82 0 0
3 0 0 259830224 46024 2710408 0 0 0 0 1692450 197212 0 18 82 0 0
As expected, number of interrupts per second is very different.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Van Jacobson <vanj@google.com>
Cc: Jerry Chu <hkchu@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And update __sk_queue_drop_skb() to work on the specified queue.
This will help the udp protocol to use an additional private
rx queue in a later patch.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In general, rtnetlink dumps do not anticipate failure to dump a single
object (e.g., link or route) on a single pass. As both route and link
objects have grown via more attributes, that is no longer a given.
netlink dumps can handle a failure if the dump function returns an
error; specifically, netlink_dump adds the return code to the response
if it is <= 0 so userspace is notified of the failure. The missing
piece is the rtnetlink dump functions returning the error.
Fix route and link dump functions to return the errors if no object is
added to an skb (detected by skb->len != 0). IPv6 route dumps
(rt6_dump_route) already return the error; this patch updates IPv4 and
link dumps. Other dump functions may need to be ajusted as well.
Reported-by: Jan Moskyto Matejka <mq@ucw.cz>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I should have known that lowering skb->truesize was dangerous :/
In case packets are not leaving the host via a standard Ethernet device,
but looped back to local sockets, bad things can happen, as reported
by Michael Madsen ( https://bugzilla.kernel.org/show_bug.cgi?id=195713 )
So instead of tweaking skb->truesize, lets change skb->destructor
and keep a reference on the owner socket via its sk_refcnt.
Fixes: f2f872f927 ("netem: Introduce skb_orphan_partial() helper")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Michael Madsen <mkm@nabto.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While working on the iproute2 generic XDP frontend, I noticed that
as of right now it's possible to have native *and* generic XDP
programs loaded both at the same time for the case when a driver
supports native XDP.
The intended model for generic XDP from b5cdae3291 ("net: Generic
XDP") is, however, that only one out of the two can be present at
once which is also indicated as such in the XDP netlink dump part.
The main rationale for generic XDP is to ease accessibility (in
case a driver does not yet have XDP support) and to generically
provide a semantical model as an example for driver developers
wanting to add XDP support. The generic XDP option for an XDP
aware driver can still be useful for comparing and testing both
implementations.
However, it is not intended to have a second XDP processing stage
or layer with exactly the same functionality of the first native
stage. Only reason could be to have a partial fallback for future
XDP features that are not supported yet in the native implementation
and we probably also shouldn't strive for such fallback and instead
encourage native feature support in the first place. Given there's
currently no such fallback issue or use case, lets not go there yet
if we don't need to.
Therefore, change semantics for loading XDP and bail out if the
user tries to load a generic XDP program when a native one is
present and vice versa. Another alternative to bailing out would
be to handle the transition from one flavor to another gracefully,
but that would require to bring the device down, exchange both
types of programs, and bring it up again in order to avoid a tiny
window where a packet could hit both hooks. Given this complicates
the logic for just a debugging feature in the native case, I went
with the simpler variant.
For the dump, remove IFLA_XDP_FLAGS that was added with b5cdae3291
and reuse IFLA_XDP_ATTACHED for indicating the mode. Dumping all
or just a subset of flags that were used for loading the XDP prog
is suboptimal in the long run since not all flags are useful for
dumping and if we start to reuse the same flag definitions for
load and dump, then we'll waste bit space. What we really just
want is to dump the mode for now.
Current IFLA_XDP_ATTACHED semantics are: nothing was installed (0),
a program is running at the native driver layer (1). Thus, add a
mode that says that a program is running at generic XDP layer (2).
Applications will handle this fine in that older binaries will
just indicate that something is attached at XDP layer, effectively
this is similar to IFLA_XDP_FLAGS attr that we would have had
modulo the redundancy.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit b5cdae3291 ("net: Generic XDP") we automatically fall
back to a generic XDP variant if the driver does not support native
XDP. Allow for an option where the user can specify that always the
native XDP variant should be selected and in case it's not supported
by a driver, just bail out.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix multiqueue in stmmac driver on PCI, from Andy Shevchenko.
2) cdc_ncm doesn't actually fully zero out the padding area is
allocates on TX, from Jim Baxter.
3) Don't leak map addresses in BPF verifier, from Daniel Borkmann.
4) If we randomize TCP timestamps, we have to do it everywhere
including SYN cookies. From Eric Dumazet.
5) Fix "ethtool -S" crash in aquantia driver, from Pavel Belous.
6) Fix allocation size for ntp filter bitmap in bnxt_en driver, from
Dan Carpenter.
7) Add missing memory allocation return value check to DSA loop driver,
from Christophe Jaillet.
8) Fix XDP leak on driver unload in qed driver, from Suddarsana Reddy
Kalluru.
9) Don't inherit MC list from parent inet connection sockets, another
syzkaller spotted gem. Fix from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits)
dccp/tcp: do not inherit mc_list from parent
qede: Split PF/VF ndos.
qed: Correct doorbell configuration for !4Kb pages
qed: Tell QM the number of tasks
qed: Fix VF removal sequence
qede: Fix XDP memory leak on unload
net/mlx4_core: Reduce harmless SRIOV error message to debug level
net/mlx4_en: Avoid adding steering rules with invalid ring
net/mlx4_en: Change the error print to debug print
drivers: net: wimax: i2400m: i2400m-usb: Use time_after for time comparison
DECnet: Use container_of() for embedded struct
Revert "ipv4: restore rt->fi for reference counting"
net: mdio-mux: bcm-iproc: call mdiobus_free() in error path
net: ethernet: ti: cpsw: adjust cpsw fifos depth for fullduplex flow control
ipv6: reorder ip6_route_dev_notifier after ipv6_dev_notf
net: cdc_ncm: Fix TX zero padding
stmmac: pci: split out common_default_data() helper
stmmac: pci: RX queue routing configuration
stmmac: pci: TX and RX queue priority configuration
stmmac: pci: set default number of rx and tx queues
...
We now have memalloc_noreclaim_{save,restore} helpers for robust setting
and clearing of PF_MEMALLOC. Let's convert the code which was using the
generic tsk_restore_flags(). No functional change.
[vbabka@suse.cz: in net/core/sock.c the hunk is missing]
Link: http://lkml.kernel.org/r/20170405074700.29871-4-vbabka@suse.cz
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Josef Bacik <jbacik@fb.com>
Cc: Lee Duncan <lduncan@suse.com>
Cc: Chris Leech <cleech@redhat.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Wouter Verhelst <w@uter.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
fq_alloc_node, alloc_netdev_mqs and netif_alloc* open code kmalloc with
vmalloc fallback. Use the kvmalloc variant instead. Keep the
__GFP_REPEAT flag based on explanation from Eric:
"At the time, tests on the hardware I had in my labs showed that
vmalloc() could deliver pages spread all over the memory and that was
a small penalty (once memory is fragmented enough, not at boot time)"
The way how the code is constructed means, however, that we prefer to go
and hit the OOM killer before we fall back to the vmalloc for requests
<=32kB (with 4kB pages) in the current code. This is rather disruptive
for something that can be achived with the fallback. On the other hand
__GFP_REPEAT doesn't have any useful semantic for these requests. So
the effect of this patch is that requests which fit into 32kB will fall
back to vmalloc easier now.
Link: http://lkml.kernel.org/r/20170306103327.2766-3-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Eric Dumazet <edumazet@google.com>
Cc: David Miller <davem@davemloft.net>
Cc: Shakeel Butt <shakeelb@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Whole point of randomization was to hide server uptime, but an attacker
can simply start a syn flood and TCP generates 'old style' timestamps,
directly revealing server jiffies value.
Also, TSval sent by the server to a particular remote address vary
depending on syncookies being sent or not, potentially triggering PAWS
drops for innocent clients.
Lets implement proper randomization, including for SYNcookies.
Also we do not need to export sysctl_tcp_timestamps, since it is not
used from a module.
In v2, I added Florian feedback and contribution, adding tsoff to
tcp_get_cookie_sock().
v3 removed one unused variable in tcp_v4_connect() as Florian spotted.
Fixes: 95a22caee3 ("tcp: randomize tcp timestamp offsets for each connection")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Florian Westphal <fw@strlen.de>
Tested-by: Florian Westphal <fw@strlen.de>
Cc: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IFLA_PHYS_PORT_NAME is a string attribute, so terminate it with \0.
Otherwise libnl3 fails to validate netlink messages with this attribute.
"ip -detail a" assumes too that the attribute is NUL-terminated when
printing it. It often was, due to padding.
I noticed this as libvirtd failing to start on a system with sfc driver
after upgrading it to Linux 4.11, i.e. when sfc added support for
phys_port_name.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Millar:
"Here are some highlights from the 2065 networking commits that
happened this development cycle:
1) XDP support for IXGBE (John Fastabend) and thunderx (Sunil Kowuri)
2) Add a generic XDP driver, so that anyone can test XDP even if they
lack a networking device whose driver has explicit XDP support
(me).
3) Sparc64 now has an eBPF JIT too (me)
4) Add a BPF program testing framework via BPF_PROG_TEST_RUN (Alexei
Starovoitov)
5) Make netfitler network namespace teardown less expensive (Florian
Westphal)
6) Add symmetric hashing support to nft_hash (Laura Garcia Liebana)
7) Implement NAPI and GRO in netvsc driver (Stephen Hemminger)
8) Support TC flower offload statistics in mlxsw (Arkadi Sharshevsky)
9) Multiqueue support in stmmac driver (Joao Pinto)
10) Remove TCP timewait recycling, it never really could possibly work
well in the real world and timestamp randomization really zaps any
hint of usability this feature had (Soheil Hassas Yeganeh)
11) Support level3 vs level4 ECMP route hashing in ipv4 (Nikolay
Aleksandrov)
12) Add socket busy poll support to epoll (Sridhar Samudrala)
13) Netlink extended ACK support (Johannes Berg, Pablo Neira Ayuso,
and several others)
14) IPSEC hw offload infrastructure (Steffen Klassert)"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2065 commits)
tipc: refactor function tipc_sk_recv_stream()
tipc: refactor function tipc_sk_recvmsg()
net: thunderx: Optimize page recycling for XDP
net: thunderx: Support for XDP header adjustment
net: thunderx: Add support for XDP_TX
net: thunderx: Add support for XDP_DROP
net: thunderx: Add basic XDP support
net: thunderx: Cleanup receive buffer allocation
net: thunderx: Optimize CQE_TX handling
net: thunderx: Optimize RBDR descriptor handling
net: thunderx: Support for page recycling
ipx: call ipxitf_put() in ioctl error path
net: sched: add helpers to handle extended actions
qed*: Fix issues in the ptp filter config implementation.
qede: Fix concurrency issue in PTP Tx path processing.
stmmac: Add support for SIMATIC IOT2000 platform
net: hns: fix ethtool_get_strings overflow in hns driver
tcp: fix wraparound issue in tcp_lp
bpf, arm64: fix jit branch offset related to ldimm64
bpf, arm64: implement jiting of BPF_XADD
...
Pull splice updates from Al Viro:
"These actually missed the last cycle; the branch itself is from last
December"
* 'work.splice' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
make nr_pages calculation in default_file_splice_read() a bit less ugly
splice/tee/vmsplice: validate flags
splice_pipe_desc: kill ->flags
remove spd_release_page()
Pull iov_iter updates from Al Viro:
"Cleanups that sat in -next + -stable fodder that has just missed 4.11.
There's more iov_iter work in my local tree, but I'd prefer to push
the stuff that had been in -next first"
* 'work.iov_iter' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
iov_iter: don't revert iov buffer if csum error
generic_file_read_iter(): make use of iov_iter_revert()
generic_file_direct_write(): make use of iov_iter_revert()
orangefs: use iov_iter_revert()
sctp: switch to copy_from_iter_full()
net/9p: switch to copy_from_iter_full()
switch memcpy_from_msg() to copy_from_iter_full()
rds: make use of iov_iter_revert()
Fix kdoc parameter spelling from extact to extack.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch 3278682123 (make skb_copy_datagram_msg() et.al. preserve
->msg_iter on error) will revert the iov buffer if copy to iter
failed, but it didn't copy any datagram if the skb_checksum_complete
error, so no need to revert any data at this place.
v2: Sabrina notice that return -EFAULT when checksum error is not correct
here, it would confuse the caller about the return value, so fix it.
Fixes: 3278682123 ("make skb_copy_datagram_msg() et.al. preserve->msg_iter on error")
Cc: stable@vger.kernel.org # v4.11
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Matthias Schiffer