When disabling HE due to the lack of HT/VHT, do it
at an earlier stage to avoid advertising HE capabilities IE.
Also, at this point, no need to check if AP supports HE, since
it is already checked earlier (in ieee80211_prep_channel).
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Up until now, the IEEE80211_STA_DISABLE_HE flag was set only based
on whether the AP has advertised HE capabilities.
This flag should be set also if STA does not support HE
(regardless of the AP support).
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Similar to WMM IE, if MU_EDCA IE parameters changed (or ceased to exist)
tell the Driver about it.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
TWT is a feature that was added in 11ah and enhanced in
11ax. There are two bits that need to be set if we want
to use the feature in 11ax: one in the HE Capability IE
and one in the Extended Capability IE. This is because
of backward compatibility between 11ah and 11ax.
In order to simplify the flow for the low level driver
in managed mode, aggregate the two bits and add a boolean
that tells whether TWT is supported or not, but only if
11ax is supported.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we build AMSDU from GSO packets, it can lead to
bad results if anyone tries to call skb_gso_segment
on the packets.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
At the place where this code lives now, the skb can never be
NULL, so we can remove the pointless NULL check.
It seems to exist because this code was moved around a few times
and originally came from a place where it could in fact be NULL.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This isn't really a problem now, but it means that the function
has a few NULL checks that are only relevant when coming from
the initial interface added in mac80211, and that's confusing.
Just pass non-NULL (but equivalently empty) in that case and
remove all the NULL checks.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The monitor interface Rx handling of SKBs that contain only
radiotap information was buggy as it tried to access the
SKB assuming it contains a frame.
To fix this, check the RX_FLAG_NO_PSDU flag in the Rx status
(indicting that the SKB contains only radiotap information),
and do not perform data path specific processing when the flag
is set.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The pointer and corresponding length is always set in pairs
in cfg80211, so no need to have this strange defensive check
that also confuses static checkers. Clean it up.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Recently TXQ teardown was moved earlier in ieee80211_unregister_hw(),
to avoid a use-after-free of the netdev data. However, interfaces
aren't fully removed at the point, and cfg80211_shutdown_all_interfaces
can for example, TX a deauth frame. Move the TXQ teardown to the
point between cfg80211_shutdown_all_interfaces and the free of
netdev queues, so we can be sure they are torn down before netdev
is freed, but after there is no ongoing TX.
Fixes: 77cfaf52ec ("mac80211: Run TXQ teardown code before de-registering interfaces")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The iTXQs stop/wake queue mechanism involves a whole bunch
of locks and this is probably why the call to
ieee80211_wake_txqs is deferred to a tasklet when called from
__ieee80211_wake_queue.
Another advantage of that is that ieee80211_wake_txqs might
call the wake_tx_queue() callback and then the driver may
call mac80211 which will call it back in the same context.
The bug I saw is that when we send a deauth frame as a
station we do:
flush(drop=1)
tx deauth
flush(drop=0)
While we flush we stop the queues and wake them up
immediately after we finished flushing. The problem here is
that the tasklet that de-facto enables the queue may not have
run until we send the deauth. Then the deauth frame is sent
to the driver (which is surprising by itself), but the driver
won't get anything useful from ieee80211_tx_dequeue because
the queue is stopped (or more precisely because
vif->txqs_stopped[0] is true).
Then the deauth is not sent. Later on, the tasklet will run,
but that'll be too late. We'll already have removed all the
vif etc...
Fix this by calling ieee80211_wake_txqs synchronously if we
are not waking up the queues from the driver (we check the
reason to determine that). This makes the code really
convoluted because we may call ieee80211_wake_txqs from
__ieee80211_wake_queue. The latter assumes that
queue_stop_reason_lock has been taken by the caller and
ieee80211_wake_txqs may release the lock to send the frames.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Lubomir Rintel recently pointed out a dead link for o11s.org, and
repointed it to a still live, but also stale website. As far as I
know, no one is updating the content at open80211s.org.
Since this Kconfig text was originally written, though, the 802.11s
mesh drafts were approved and ultimately rolled into 802.11 proper.
Meanwhile, the implementation has converged on the final standard,
so we can lose all of the text here and provide something that's a
little more helpful and accurate.
Signed-off-by: Bob Copeland <bobcopeland@fb.com>
Reviewed-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Steve deRosier <derosier@cal-sierra.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
NullFunc packets should never be duplicate just like
QoS-NullFunc packets.
We saw a client that enters / exits power save with
NullFunc frames (and not with QoS-NullFunc) despite the
fact that the association supports HT.
This specific client also re-uses a non-zero sequence number
for different NullFunc frames.
At some point, the client had to send a retransmission of
the NullFunc frame and we dropped it, leading to a
misalignment in the power save state.
Fix this by never consider a NullFunc frame as duplicate,
just like we do for QoS NullFunc frames.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=201449
CC: <stable@vger.kernel.org>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the buffered broadcast queue contains packets, letting new packets bypass
that queue can lead to heavy reordering, since the driver is probably throttling
transmission of buffered multicast packets after beacons.
Keep buffering packets until the buffer has been cleared (and no client
is in powersave mode).
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make it behave like regular ieee80211_tx_status calls, except for the lack of
filtered frame processing.
This fixes spurious low-ack triggered disconnections with powersave clients
connected to an AP.
Fixes: f027c2aca0 ("mac80211: add ieee80211_tx_status_noskb")
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
'cipher' algorithms (single block ciphers) are always synchronous, so
passing CRYPTO_ALG_ASYNC in the mask to crypto_alloc_cipher() has no
effect. Many users therefore already don't pass it, but some still do.
This inconsistency can cause confusion, especially since the way the
'mask' argument works is somewhat counterintuitive.
Thus, just remove the unneeded CRYPTO_ALG_ASYNC flags.
This patch shouldn't change any actual behavior.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When peering is in userspace, some implementations may want to control
which peers are accepted based on RSSI in addition to the information
elements being sent today. Add signal level so that info is available
to clients.
Signed-off-by: Bob Copeland <bobcopeland@fb.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When userspace is controlling mesh routing, it may have better
knowledge about whether a mesh STA is connected to a mesh
gate than the kernel mpath table. Add dot11MeshConnectedToMeshGate
to the mesh config so that such applications can explicitly
signal that a mesh STA is connected to a gate, which will then
be advertised in the beacon.
Signed-off-by: Bob Copeland <bobcopeland@fb.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Capture the current state of gate connectivity from the mesh
formation field in mesh config whenever we receive a beacon,
and report that via GET_STATION. This allows applications
doing mesh peering in userspace to make peering decisions
based on peers' current upstream connectivity.
Signed-off-by: Bob Copeland <bobcopeland@fb.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The Connected to Mesh Gate subfield (802.11-2016 9.4.2.98.7) in the Mesh
Formation Info field is currently unset. This field may be useful in
determining which MBSSes to join or which mesh STAs to peer with.
If this mesh STA is a gate, by having turned on mesh gate announcements,
or if we have a path to one (e.g. by having received RANNs) then set this
bit to 1.
Signed-off-by: Bob Copeland <bobcopeland@fb.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In some cases, like in the rsi driver hardware scan offload, there
may be scenarios in which hardware scan might not be available or
desirable.
Allow drivers to cope with this by letting them fall back to software
scan by returning the special value 1 from the hardware scan method.
Requested-by: Sushant Kumar Mishra <sushant2k1513@gmail.com>
Requested-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's nothing much for mac80211 to do, so only pass through
the requests with minimal checks and tracing. The driver must
call cfg80211's results APIs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We have a bool and an __le16 called qos, rename the inner __le16
to 'qoshdr' to make it more obvious and to avoid sparse warnings.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We have a macro here that uses an inner variable 'i' that
also exists in the outer scope - use '_i' in the macro.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We have a pointer called 'tidstats' that shadows a bool function
argument with the same name, but we actually only use it once so
just remove the pointer.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This variable shadows something that gets generated inside
the tracing macros, which causes sparse to warn. Avoid it
so sparse output is more readable, even if it doesn't seem
to cause any trouble.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the FTM responder settings are changed simultaneously with
the CSA beacon, the buffer size allocated isn't sufficient and
we'll have a heap overrun. Fix this.
While at it, also clean up the ftm_responder assignment, doing
it only if ftm_responder is non-zero is valid as it's 0 to start
with, but not really useful to understand the code.
Fixes: bc847970f4 ("mac80211: support FTM responder configuration/statistics")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This fixes stale beacon-int values that would keep a netdev
from going up.
To reproduce:
Create two VAP on one radio.
vap1 has beacon-int 100, start it.
vap2 has beacon-int 240, start it (and it will fail
because beacon-int mismatch).
reconfigure vap2 to have beacon-int 100 and start it.
It will fail because the stale beacon-int 240 will be used
in the ifup path and hostapd never gets a chance to set the
new beacon interval.
Cc: stable@vger.kernel.org
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211_sta_opmode_change_notify needs a gfp_t flag to hint the nl80211
stack when allocating new skb, but it is called under tasklet context
here with GFP_KERNEL and kernel will yield a warning about it.
Cc: stable@vger.kernel.org
Fixes: ff84e7bfe1 ("mac80211: Add support to notify ht/vht opmode modification.")
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
ACKed-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the missing unlock before return from function
ieee80211_mark_sta_auth() in the error handling case.
Cc: stable@vger.kernel.org
Fixes: fc107a9330 ("mac80211: Helper function for marking STA authenticated")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
[use result variable/label instead of duplicating]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Current mac80211 has provision to update tx status through
ieee80211_tx_status() and ieee80211_tx_status_ext(). But
drivers like ath10k updates the tx status from the skb except
txrate, txrate will be updated from a different path, peer stats.
Using ieee80211_tx_status_ext() in two different paths
(one for the stats, one for the tx rate) would duplicate
the stats instead.
To avoid this stats duplication, ieee80211_tx_rate_update()
is implemented.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
[minor commit message editing, use initializers in code]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
New bss param ftm_responder is used to notify the driver to
enable fine timing request (FTM) responder role in AP mode.
Plumb the new cfg80211 API for FTM responder statistics through to
the driver API in mac80211.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previous implementation of SAE authentication in infrastructure BSS was
somewhat restricting and not exactly clean way of handling the two
auth() operations. This ended up removing and re-adding the STA entry
for the AP in the middle of authentication and also messing up
authentication state tracking through the sequence of four
Authentication frames. Furthermore, this did not work if the AP ended up
sending out SAE Confirm (auth trans #2) immediately after SAE Commit
(auth trans #1) before the station had time to transmit its SAE Confirm.
Clean up authentication state handling for the SAE case to allow two
rounds of auth() calls without dropping all state between those
operations. Track peer Confirmed status and mark authentication
completed only once both ends have confirmed.
ieee80211_mgd_auth() check for EBUSY cases is now handling only the
pending association (ifmgd->assoc_data) while all pending authentication
(ifmgd->auth_data) cases are allowed to proceed to allow user space to
start a new connection attempt from scratch even if the previously
requested authentication is still waiting completion. This is needed to
avoid making SAE error cases with retries take excessive amount of time
with no means for the user space to stop that (apart from setting the
netdev down).
As an extra bonus, the end of ieee80211_rx_mgmt_auth() can be cleaned up
to avoid the extra copy of the cfg80211_rx_mlme_mgmt() call for ongoing
SAE authentication since the new ieee80211_mark_sta_auth() helper
function can handle both completion of authentication and updates to the
STA entry under the same condition and there is no need to return from
the function between those operations.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This makes it easier to conditionally replace full allocation of
auth_data to use reallocation for the case of continuing SAE
authentication. Furthermore, there was not really any point in having
this check done so late in the function after having already completed
number of steps that cannot be used anyway in the error case.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Authentication exchange can be completed in both TX and RX paths for
SAE, so move this common functionality into a helper function to avoid
having to implement practically the same operations in two places when
extending SAE implementation in the following commits.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When there are few packets (e.g. for sampling attempts), the exponentially
weighted variance is usually vastly overestimated, making the resulting data
essentially useless. As far as I know, there has not been any practical use
for this, so let's not waste any cycles on it.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These rates are highly unlikely to be used quickly, even if the link
deteriorates rapidly. This improves throughput in cases where CCK rates
are not reliable enough to be skipped entirely during sampling.
Sampling these rates regularly can cost a lot of airtime.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Long/short preamble selection cannot be sampled separately, since it
depends on the BSS state. Because of that, sampling attempts to
currently not used preamble modes are not counted in the statistics,
which leads to CCK rates being sampled too often.
Fix statistics accounting for long/short preamble by increasing the
index where necessary.
Fix excessive CCK rate sampling by dropping unsupported sample attempts.
This improves throughput on 2.4 GHz channels
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes a harmless underflow issue when CCK rates are actively being used
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mi->supported[MINSTREL_CCK_GROUP] needs to be updated
short preamble rates need to be marked as supported regardless of
whether it's currently enabled. Its state can change at any time without
a rate_update call.
Fixes: 782dda00ab ("mac80211: minstrel_ht: move short preamble check out of get_rate")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
By storing a shift value for all duration values of a group, we can
reduce precision by a neglegible amount to make it fit into a u16 value.
This improves cache footprint and reduces size:
Before:
text data bss dec hex filename
10024 116 0 10140 279c rc80211_minstrel_ht.o
After:
text data bss dec hex filename
9368 116 0 9484 250c rc80211_minstrel_ht.o
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Legacy-only devices are not very common and the overhead of the extra
code for HT and VHT rates is not big enough to justify all those extra
lines of code to make it optional.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
debugfs entries are cleaned up by debugfs_remove_recursive already.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If peer support reception of STBC and LDPC, enable them for better
performance.
Signed-off-by: Chaitanya TK <chaitanya.mgit@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
I'm not really sure exactly _why_ I've been carrying a note
for what's probably _years_ to check that we don't do this,
but we clearly do reflect frames back to the station itself
if it sends such.
One way or the other, it's useless since the station doesn't
really need the AP to talk to itself, so suppress it.
While at it, clarify some of the logic by removing skb->data
references in favour of the destination address (pointer) we
already have separately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Merge net-next, which pulled in net, so I can merge a few more
patches that would otherwise conflict.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Minor conflict in net/core/rtnetlink.c, David Ahern's bug fix in 'net'
overlapped the renaming of a netlink attribute in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable j will be initialized at trailing step.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix to return a negative error code -ENOMEM from the kmemdup
error handling case instead of 0.
Fixes: 09b4a4faf9 ("mac80211: introduce capability flags for VHT EXT NSS support")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers that do not have the BUFF_MMPDU_TXQ flag set will not have a
TXQ for the special TID = 16.
In this case, the last member in the *struct ieee80211_sta* txq array
will be NULL.
We must check this in order not to get a NULL pointer dereference when
iterating the txq array.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
key->sta is only valid after ieee80211_key_link, which is called later
in this function. Because of that, the IEEE80211_KEY_FLAG_RX_MGMT is
never set when management frame protection is enabled.
Fixes: e548c49e6d ("mac80211: add key flag for management keys")
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Monitor mode interfaces with the active flag are passed down to the driver.
Drivers using TXQ expect that all interfaces have allocated TXQs before
they get added.
Fixes: 79af1f8661 ("mac80211: avoid allocating TXQs that won't be used")
Cc: stable@vger.kernel.org
Reported-by: Catrinel Catrinescu <cc@80211.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
TX status reporting to ieee80211s is through ieee80211s_update_metric.
There are two problems about ieee80211s_update_metric:
1. The purpose is to estimate the fail probability
to a specific link. No need to restrict to data frame.
2. Current implementation does not work if wireless driver does not
pass tx_status with skb.
Fix this by removing ieee80211_is_data condition, passing
ieee80211_tx_status directly to ieee80211s_update_metric, and
putting it in both __ieee80211_tx_status and ieee80211_tx_status_ext.
Signed-off-by: Yuan-Chi Pang <fu3mo6goo@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the TDLS setup happens over a connection to an AP that
doesn't have QoS, we nevertheless assign a non-zero TID
(skb->priority) and queue mapping, which may confuse us or
drivers later.
Fix it by just assigning the special skb->priority and then
using ieee80211_select_queue() just like other data frames
would go through.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In our environment running lots of mesh nodes, we are seeing the
pending queue hang periodically, with the debugfs queues file showing
lines such as:
00: 0x00000000/348
i.e. there are a large number of frames but no stop reason set.
One way this could happen is if queue processing from the pending
tasklet exited early without processing all frames, and without having
some future event (incoming frame, stop reason flag, ...) to reschedule
it.
Exactly this can occur today if ieee80211_tx() returns false due to
packet drops or power-save buffering in the tx handlers. In the
past, this function would return true in such cases, and the change
to false doesn't seem to be intentional. Fix this case by reverting
to the previous behavior.
Fixes: bb42f2d13f ("mac80211: Move reorder-sensitive TX handlers to after TXQ dequeue")
Signed-off-by: Bob Copeland <bobcopeland@fb.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Both old and new cannot be NULL at the same time, hence checking
new when old is not NULL is unnecessary.
Also, notice that new is being dereferenced before it is checked:
idx = new->conf.keyidx;
The above triggers a static code analysis warning.
Address this by removing the NULL check on new and adding a code
comment based on the following piece of code:
387 /* caller must provide at least one old/new */
388 if (WARN_ON(!new && !old))
389 return 0;
Addresses-Coverity-ID: 1473176 ("Dereference before null check")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some hardwares have limitations on the packets' type in AMSDU.
Add an optional driver callback to determine if two skbs can
be used in the same AMSDU or not.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers may have AMSDU size limitation per TID, due to
HW constrains. Add an option to set this limit.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We have a TXQ abstraction for non-data packets that need
powersave buffering. Since the AP cannot sleep, in case
of station we can use this TXQ for all management frames,
regardless if they are bufferable. Add HW flag to allow
that.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Align to new 11ax draft D3.0. Change/add new MAC and PHY capabilities
and update drivers' 11ax capabilities and mac80211's debugfs
accordingly.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
After masking the he_oper_params, to get the requested values as
integers one must rshift and not lshift. Fix that by using the
le32_get_bits() macro.
Fixes: 41cbb0f5a2 ("mac80211: add support for HE")
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
[converted to use le32_get_bits()]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For certain sounding frames, it may be useful to report them
to userspace even though they don't have a PSDU in order to
determine the PHY parameters (e.g. VHT rate/stream config.)
Add support for this to mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Otherwise the offchannel frame might be queued due to
IEEE80211_QUEUE_STOP_REASON_PS and later dropped (in
ieee80211_tx_frags()). Anyway, it doesn't make much sense to wake up
the device during ROC.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a frame is dropped for any reason, mac80211 wouldn't report the TX
status back to user space.
As the user space may rely on the TX_STATUS to kick its state
machines, resends etc, it's better to just report this frame as not
acked instead.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Rekeying PTK keys without "Extended Key ID for Individually Addressed
Frames" did use a procedure not suitable to replace in-use keys and
could caused the following issues:
1) Freeze caused by incoming frames:
If the local STA installed the key prior to the remote STA we still
had the old key active in the hardware when mac80211 switched over
to the new key.
Therefore there was a window where the card could hand over frames
decoded with the old key to mac80211 and bump the new PN (IV) value
to an incorrect high number. When it happened the local replay
detection silently started to drop all frames sent with the new key.
2) Freeze caused by outgoing frames:
If mac80211 was providing the PN (IV) and handed over a clear text
frame for encryption to the hardware prior to a key change the
driver/card could have processed the queued frame after switching
to the new key. This bumped the PN value on the remote STA to an
incorrect high number, tricking the remote STA to discard all frames
we sent later.
3) Freeze caused by RX aggregation reorder buffer:
An aggregation session started with the old key and ending after the
switch to the new key also bumped the PN to an incorrect high number,
freezing the connection quite similar to 1).
4) Freeze caused by repeating lost frames in an aggregation session:
A driver could repeat a lost frame and encrypt it with the new key
while in a TX aggregation session without updating the PN for the
new key. This also could freeze connections similar to 2).
5) Clear text leak:
Removing encryption offload from the card cleared the encryption
offload flag only after the card had deleted the key and we did not
stop TX during the rekey. The driver/card could therefore get
unencrypted frames from mac80211 while no longer be instructed to
encrypt them.
To prevent those issues the key install logic has been changed:
- Mac80211 divers known to be able to rekey PTK0 keys have to set
@NL80211_EXT_FEATURE_CAN_REPLACE_PTK0,
- mac80211 stops queuing frames depending on the key during the replace
- the key is first replaced in the hardware and after that in mac80211
- and mac80211 stops/blocks new aggregation sessions during the rekey.
For drivers not setting
@NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 the user space must avoid PTK
rekeys if "Extended Key ID for Individually Addressed Frames" is not
being used. Rekeys for mac80211 drivers without this flag will generate a
warning and use an extra call to ieee80211_flush_queues() to both
highlight and try to prevent the issues with not updated drivers.
The core of the fix changes the key install procedure from:
- atomic switch over to the new key in mac80211
- remove the old key in the hardware (stops encryption offloading, fall
back to software encryption with a potential clear text packet leak
in between)
- delete the inactive old key in mac80211
- enable hardware encryption offloading for the new key
to:
- if it's a PTK mark the old key as tainted to drop TX frames with the
outgoing key
- replace the key in hardware with the new one
- atomic switch over to the new (not marked as tainted) key in
mac80211 (which also resumes TX)
- delete the inactive old key in mac80211
With the new sequence the hardware will be unable to decrypt frames
encrypted with the old key prior to switching to the new key in mac80211
and thus prevent PNs from packets decrypted with the old key to be
accounted against the new key.
For that to work the drivers have to provide a clear boundary.
Mac80211 drivers setting @NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 confirm
to provide it and mac80211 will then be able to correctly rekey in-use
PTK keys with those drivers.
The mac80211 requirements for drivers to set the flag have been added to
the "Hardware crypto acceleration" documentation section. It drills down
to:
The drivers must not hand over frames decrypted with the old key to
mac80211 once the call to set_key() with %DISABLE_KEY has been
completed. It's allowed to either drop or continue to use the old key
for any outgoing frames which are already in the queues, but it must not
send out any of them unencrypted or encrypted with the new key.
Even with the new boundary in place aggregation sessions with the
reorder buffer are problematic:
RX aggregation session started prior and completed after the rekey could
still dump frames received with the old key at mac80211 after it
switched over to the new key. This is side stepped by stopping all (RX
and TX) aggregation sessions when replacing a PTK key and hardware key
offloading.
Stopping TX aggregation sessions avoids the need to get
the PNs (IVs) updated in frames prepared for the old key and
(re)transmitted after the switch to the new key. As a bonus it improves
the compatibility when the remote STA is not handling rekeys as it
should.
When using software crypto aggregation sessions are not stopped.
Mac80211 won't be able to decode the dangerous frames and discard them
without special handling.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
[trim overly long rekey warning]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As before with HE, the data needs to be provided by the
driver in the skb head, since there's not enough space
in the skb CB.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make it possibly for drivers to adjust the default skb_pacing_shift
by storing it in the hardware struct.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
[adjust commit log, move & adjust comment]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When taking VHT capabilities for a station, copy the new
fields if we support them as a transmitter. Also adjust
the maximum bandwidth the station supports appropriately.
Also, since it was missing, copy tx_highest and rx_highest.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With newer VHT implementations, it's necessary to look at the
HT operation's CCFS2 field to identify the actual bandwidth
used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Depending on whether or not rate control supports selecting
rates depending on the bandwidth, we can use VHT extended
NSS support. In essence, this is dot11VHTExtendedNSSBWCapable
from the spec, since depending on that we'll need to parse
the bandwidth.
If needed, also set/clear the VHT Capability Element bit for
this capability so that we don't advertise it erroneously or
don't advertise it when we actually use it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In AP mode, If AP advertises HE capabilities, set to true
bss_conf::he_supported so that the Driver knows about it.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers may want to also use the TXQ abstraction with
non-data packets that need powersave buffering, so add a
hardware flag to allow this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These checks aren't necessary, cfg80211 never passes NULL.
Some static checkers complain about the missing checks on
the next line, but really the NULL checks are unnecessary.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Export HE capabilities information via debugfs, similar to HT & VHT.
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* various A-MSDU building fixes (currently only affects mt76)
* syzkaller & spectre fixes in hwsim
* TXQ vs. teardown fix that was causing crashes
* embed WMM info in reg rule, bad code here had been causing crashes
* one compilation issue with fix from Arnd (rfkill-gpio includes)
* fixes for a race and bad data during/after channel switch
* nl80211: a validation fix, attribute type & unit fixes
along with other small fixes.
-----BEGIN PGP SIGNATURE-----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=lLBA
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2018-09-03' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Here are quite a large number of fixes, notably:
* various A-MSDU building fixes (currently only affects mt76)
* syzkaller & spectre fixes in hwsim
* TXQ vs. teardown fix that was causing crashes
* embed WMM info in reg rule, bad code here had been causing crashes
* one compilation issue with fix from Arnd (rfkill-gpio includes)
* fixes for a race and bad data during/after channel switch
* nl80211: a validation fix, attribute type & unit fixes
along with other small fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When tracing is enabled, all the debug messages are recorded and must
not exceed MAX_MSG_LEN (100) columns. Longer debug messages grant the
user with:
WARNING: CPU: 3 PID: 32642 at /tmp/wifi-core-20180806094828/src/iwlwifi-stack-dev/net/mac80211/./trace_msg.h:32 trace_event_raw_event_mac80211_msg_event+0xab/0xc0 [mac80211]
Workqueue: phy1 ieee80211_iface_work [mac80211]
RIP: 0010:trace_event_raw_event_mac80211_msg_event+0xab/0xc0 [mac80211]
Call Trace:
__sdata_dbg+0xbd/0x120 [mac80211]
ieee80211_ibss_rx_queued_mgmt+0x15f/0x510 [mac80211]
ieee80211_iface_work+0x21d/0x320 [mac80211]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the driver fails to properly prepare for the channel
switch, mac80211 will disconnect. If the CSA IE had mode
set to 1, it means that the clients are not allowed to send
any Tx on the current channel, and that includes the
deauthentication frame.
Make sure that we don't send the deauthentication frame in
this case.
In iwlwifi, this caused a failure to flush queues since the
firmware already closed the queues after having parsed the
CSA IE. Then mac80211 would wait until the deauthentication
frame would go out (drv_flush(drop=false)) and that would
never happen.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When performing a channel switch flow for a managed interface, the
flow did not update the bandwidth of the AP station and the rate
scale algorithm. In case of a channel width downgrade, this would
result with the rate scale algorithm using a bandwidth that does not
match the interface channel configuration.
Fix this by updating the AP station bandwidth and rate scaling algorithm
before the actual channel change in case of a bandwidth downgrade, or
after the actual channel change in case of a bandwidth upgrade.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We hit a problem with iwlwifi that was caused by a bug in
mac80211. A bug in iwlwifi caused the firwmare to crash in
certain cases in channel switch. Because of that bug,
drv_pre_channel_switch would fail and trigger the restart
flow.
Now we had the hw restart worker which runs on the system's
workqueue and the csa_connection_drop_work worker that runs
on mac80211's workqueue that can run together. This is
obviously problematic since the restart work wants to
reconfigure the connection, while the csa_connection_drop_work
worker does the exact opposite: it tries to disconnect.
Fix this by cancelling the csa_connection_drop_work worker
in the restart worker.
Note that this can sound racy: we could have:
driver iface_work CSA_work restart_work
+++++++++++++++++++++++++++++++++++++++++++++
|
<--drv_cs ---|
<FW CRASH!>
-CS FAILED-->
| |
| cancel_work(CSA)
schedule |
CSA work |
| |
Race between those 2
But this is not possible because we flush the workqueue
in the restart worker before we cancel the CSA worker.
That would be bullet proof if we could guarantee that
we schedule the CSA worker only from the iface_work
which runs on the workqueue (and not on the system's
workqueue), but unfortunately we do have an instance
in which we schedule the CSA work outside the context
of the workqueue (ieee80211_chswitch_done).
Note also that we should probably cancel other workers
like beacon_connection_loss_work and possibly others
for different types of interfaces, at the very least,
IBSS should suffer from the exact same problem, but for
now, do the minimum to fix the actual bug that was actually
experienced and reproduced.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In commit 9236c4523e5b ("mac80211: limit wmm params to comply
with ETSI requirements"), we have limited the WMM parameters to
comply with 802.11 and ETSI standard. Mistakenly the TXOP value
was caluclated wrong. Fix it by taking the minimum between
802.11 to ETSI to make sure we are not violating both.
Fixes: e552af0581 ("mac80211: limit wmm params to comply with ETSI requirements")
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Initialize 'n' to 2 in order to take into account also the first
packet in the estimation of max_subframe limit for a given A-MSDU
since frag_tail pointer is NULL when ieee80211_amsdu_aggregate
routine analyzes the second frame.
Fixes: 6e0456b545 ("mac80211: add A-MSDU tx support")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the error path of changing the SKB headroom of the second
A-MSDU subframe, we would not account for the already-changed
length of the first frame that just got converted to be in
A-MSDU format and thus is a bit longer now.
Fix this by doing the necessary accounting.
It would be possible to reorder the operations, but that would
make the code more complex (to calculate the necessary pad),
and the headroom expansion should not fail frequently enough
to make that worthwhile.
Fixes: 6e0456b545 ("mac80211: add A-MSDU tx support")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Do not start to aggregate packets in a A-MSDU frame (converting the
first subframe to A-MSDU, adding the header) if max_tx_fragments or
max_amsdu_subframes limits are already exceeded by it. In particular,
this happens when drivers set the limit to 1 to avoid A-MSDUs at all.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
[reword commit message to be more precise]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When building building AMSDU from non-linear SKB, we hit a
kernel panic when trying to push the padding to the tail.
Instead, put the padding at the head of the next subframe.
This also fixes the A-MSDU subframes to not have the padding
accounted in the length field and not have pad at all for
the last subframe, both required by the spec.
Fixes: 6e0456b545 ("mac80211: add A-MSDU tx support")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Reviewed-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
IEEE 802.11-2016 14.10.8.3 HWMP sequence numbering says:
If it is a target mesh STA, it shall update its own HWMP SN to
maximum (current HWMP SN, target HWMP SN in the PREQ element) + 1
immediately before it generates a PREP element in response to a
PREQ element.
Signed-off-by: Yuan-Chi Pang <fu3mo6goo@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Modify the API to include all ACK frames in average ACK
signal strength reporting, not just ACKs for data frames.
Make exposing the data conditional on implementing the
extended feature flag.
This is how it was really implemented in mac80211, update
the code there to use the new defines and clean up some of
the setting code.
Keep nl80211.h source compatibility by keeping the old names.
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
[rewrite commit log, change compatibility to be old=new
instead of the other way around, update kernel-doc,
roll in mac80211 changes, make mac80211 depend on valid
bit instead of HW flag]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current mac80211 WDS (4-address mode) can be used to cover most of the
Multi-AP requirements for Data frames per the WFA Multi-AP Specification v1.0.
When configuring AP/STA interfaces in 4-address mode, they are able to function
as fronthaul AP/backhaul STA of Multi-AP device complying below
Tx, Rx requirements except one missing STA Rx requirement added by this patch.
Multi-AP specification section 14.1 describes the following requirements:
Transmitter requirements
------------------------
1. Fronthaul AP
i) When DA!=RA of backhaul STA, must use 4-address format
ii) When DA==RA of backhaul STA, shall use either 3-address
or 4-address format with RA updated with STA MAC
(mac80211 support 4-address format via AP/VLAN interface)
2. Backhaul STA
i) When SA!=TA of backhaul STA, must use 4-address format
ii) When SA==TA of backhaul STA, shall use either 3-address
or 4-address format with RA updated with AP MAC
(mac80211 support 4-address format via use_4addr)
Receiver requirements
---------------------
1. Fronthaul AP
i) When SA!=TA of backhaul STA, must support receiving 4-address
format frames
ii) When SA==TA of backhaul STA, must support receiving both
3-address and 4-address format frames
(mac80211 support both 3-addr & 4-addr via AP/VLAN interface)
2. Backhaul STA
i) When DA!=RA of backhaul STA, must support receiving 4-address
format frames
ii) When DA==RA of backhaul STA, must support receiving both
3-address and 4-address format frames
(mac80211 support only receiving 4-address format via
use_4addr)
This patch addresses the above Rx requirement (ii) for backhaul STA to receive
unicast (DA==RA) 3-address frames in addition to 4-address frames.
The current design doesn't accept 3-address frames when configured in 4-address
mode (use_4addr). Hence add a check to allow 3-address frames when DA==RA of
backhaul STA (adhering to Table 9-26 of IEEE Std 802.11™-2016).
This case was tested with a bridged station interface when associated with
a non-mac80211 based vendor AP implementation using 3-address frames for WDS.
STA was able to support the Multi-AP Rx requirement when DA==RA. No issues,
no loops seen when tested with mac80211 based AP as well.
Verified and confirmed all other Tx and Rx requirements of AP and STA for
Multi-AP respectively. They all work using the current mac80211-WDS design.
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sometimes, it is required to stop the transmissions momentarily and
resume it later; stopping the txqs becomes very critical in scenarios where
the packet transmission has to be ceased completely. For example, during
the hardware restart, during off channel operations,
when initiating CSA(upon detecting a radar on the DFS channel), etc.
The TX queue stop/start logic in mac80211 works well in stopping the TX
when drivers make use of netdev queues, i.e, when Qdiscs in network layer
take care of traffic scheduling. Since the devices implementing
wake_tx_queue can run without Qdiscs, packets will be handed to mac80211
directly without queueing them in the netdev queues.
Also, mac80211 does not invoke any of the
netif_stop_*/netif_wake_* APIs if wake_tx_queue is implemented.
Since the queues are not stopped in this case, transmissions can continue
and this will impact negatively on the operation of the wireless device.
For example,
During hardware restart, we stop the netdev queues so that packets are
not sent to the driver. Since ath10k implements wake_tx_queue,
TX queues will not be stopped and packets might reach the hardware while
it is restarting; this can make hardware unresponsive and the only
possible option for recovery is to reboot the entire system.
There is another problem to this, it is observed that the packets
were sent on the DFS channel for a prolonged duration after radar
detection impacting the channel closing time.
We can still invoke netif stop/wake APIs when wake_tx_queue is implemented
but this could lead to packet drops in network layer; adding stop/start
logic for software TXQs in mac80211 instead makes more sense; the change
proposed adds the same in mac80211.
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make ieee80211_send_layer2_update() a common function so other drivers
can re-use it.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
I changed the way mac80211 updates the PM state of the peer.
I forgot that we could also have multicast frames from the
peer and that those frame should of course not change the
PM state of the peer: A peer goes to power save when it
needs to scan, but it won't send the broadcast Probe Request
with the PM bit set.
This made us mark the peer as awake when it wasn't and then
Intel's firmware would fail to transmit because the peer is
asleep according to its database. The driver warned about
this and it looked like this:
WARNING: CPU: 0 PID: 184 at /usr/src/linux-4.16.14/drivers/net/wireless/intel/iwlwifi/mvm/tx.c:1369 iwl_mvm_rx_tx_cmd+0x53b/0x860
CPU: 0 PID: 184 Comm: irq/124-iwlwifi Not tainted 4.16.14 #1
RIP: 0010:iwl_mvm_rx_tx_cmd+0x53b/0x860
Call Trace:
iwl_pcie_rx_handle+0x220/0x880
iwl_pcie_irq_handler+0x6c9/0xa20
? irq_forced_thread_fn+0x60/0x60
? irq_thread_dtor+0x90/0x90
The relevant code that spits the WARNING is:
case TX_STATUS_FAIL_DEST_PS:
/* the FW should have stopped the queue and not
* return this status
*/
WARN_ON(1);
info->flags |= IEEE80211_TX_STAT_TX_FILTERED;
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=199967.
Fixes: 9fef654433 ("mac80211: always update the PM state of a peer on MGMT / DATA frames")
Cc: <stable@vger.kernel.org> #4.16+
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make wmm_rule be part of the reg_rule structure. This simplifies the
code a lot at the cost of having bigger memory usage. However in most
cases we have only few reg_rule's and when we do have many like in
iwlwifi we do not save memory as it allocates a separate wmm_rule for
each channel anyway.
This also fixes a bug reported in various places where somewhere the
pointers were corrupted and we ended up doing a null-dereference.
Fixes: 230ebaa189 ("cfg80211: read wmm rules from regulatory database")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
[rephrase commit message slightly]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The mod mask for VHT capabilities intends to say that you can override
the number of STBC receive streams, and it does, but only by accident.
The IEEE80211_VHT_CAP_RXSTBC_X aren't bits to be set, but values (albeit
left-shifted). ORing the bits together gets the right answer, but we
should use the _MASK macro here instead.
Signed-off-by: Danek Duvall <duvall@comfychair.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull networking updates from David Miller:
"Highlights:
- Gustavo A. R. Silva keeps working on the implicit switch fallthru
changes.
- Support 802.11ax High-Efficiency wireless in cfg80211 et al, From
Luca Coelho.
- Re-enable ASPM in r8169, from Kai-Heng Feng.
- Add virtual XFRM interfaces, which avoids all of the limitations of
existing IPSEC tunnels. From Steffen Klassert.
- Convert GRO over to use a hash table, so that when we have many
flows active we don't traverse a long list during accumluation.
- Many new self tests for routing, TC, tunnels, etc. Too many
contributors to mention them all, but I'm really happy to keep
seeing this stuff.
- Hardware timestamping support for dpaa_eth/fsl-fman from Yangbo Lu.
- Lots of cleanups and fixes in L2TP code from Guillaume Nault.
- Add IPSEC offload support to netdevsim, from Shannon Nelson.
- Add support for slotting with non-uniform distribution to netem
packet scheduler, from Yousuk Seung.
- Add UDP GSO support to mlx5e, from Boris Pismenny.
- Support offloading of Team LAG in NFP, from John Hurley.
- Allow to configure TX queue selection based upon RX queue, from
Amritha Nambiar.
- Support ethtool ring size configuration in aquantia, from Anton
Mikaev.
- Support DSCP and flowlabel per-transport in SCTP, from Xin Long.
- Support list based batching and stack traversal of SKBs, this is
very exciting work. From Edward Cree.
- Busyloop optimizations in vhost_net, from Toshiaki Makita.
- Introduce the ETF qdisc, which allows time based transmissions. IGB
can offload this in hardware. From Vinicius Costa Gomes.
- Add parameter support to devlink, from Moshe Shemesh.
- Several multiplication and division optimizations for BPF JIT in
nfp driver, from Jiong Wang.
- Lots of prepatory work to make more of the packet scheduler layer
lockless, when possible, from Vlad Buslov.
- Add ACK filter and NAT awareness to sch_cake packet scheduler, from
Toke Høiland-Jørgensen.
- Support regions and region snapshots in devlink, from Alex Vesker.
- Allow to attach XDP programs to both HW and SW at the same time on
a given device, with initial support in nfp. From Jakub Kicinski.
- Add TLS RX offload and support in mlx5, from Ilya Lesokhin.
- Use PHYLIB in r8169 driver, from Heiner Kallweit.
- All sorts of changes to support Spectrum 2 in mlxsw driver, from
Ido Schimmel.
- PTP support in mv88e6xxx DSA driver, from Andrew Lunn.
- Make TCP_USER_TIMEOUT socket option more accurate, from Jon
Maxwell.
- Support for templates in packet scheduler classifier, from Jiri
Pirko.
- IPV6 support in RDS, from Ka-Cheong Poon.
- Native tproxy support in nf_tables, from Máté Eckl.
- Maintain IP fragment queue in an rbtree, but optimize properly for
in-order frags. From Peter Oskolkov.
- Improvde handling of ACKs on hole repairs, from Yuchung Cheng"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1996 commits)
bpf: test: fix spelling mistake "REUSEEPORT" -> "REUSEPORT"
hv/netvsc: Fix NULL dereference at single queue mode fallback
net: filter: mark expected switch fall-through
xen-netfront: fix warn message as irq device name has '/'
cxgb4: Add new T5 PCI device ids 0x50af and 0x50b0
net: dsa: mv88e6xxx: missing unlock on error path
rds: fix building with IPV6=m
inet/connection_sock: prefer _THIS_IP_ to current_text_addr
net: dsa: mv88e6xxx: bitwise vs logical bug
net: sock_diag: Fix spectre v1 gadget in __sock_diag_cmd()
ieee802154: hwsim: using right kind of iteration
net: hns3: Add vlan filter setting by ethtool command -K
net: hns3: Set tx ring' tc info when netdev is up
net: hns3: Remove tx ring BD len register in hns3_enet
net: hns3: Fix desc num set to default when setting channel
net: hns3: Fix for phy link issue when using marvell phy driver
net: hns3: Fix for information of phydev lost problem when down/up
net: hns3: Fix for command format parsing error in hclge_is_all_function_id_zero
net: hns3: Add support for serdes loopback selftest
bnxt_en: take coredump_record structure off stack
...
-----BEGIN PGP SIGNATURE-----
iJEEABYIADkWIQQUwxxKyE5l/npt8ARiEGxRG/Sl2wUCW3HajRscamFjZWsuYW5h
c3pld3NraUBnbWFpbC5jb20ACgkQYhBsURv0pdvxAwEA+qS5O9ByxlhT+BUC4ck6
nIy0ITOCXP8ySoo8VVhzjikBAPrb9lFYGvHqzKN4dYtnSILPmlTSf1t1flng2Zev
NfoE
=lNwq
-----END PGP SIGNATURE-----
Merge tag 'leds-for-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
"LED triggers improvements make the biggest part of this pull request.
The most striking ones, that allowed for nice cleanups in the triggers
are:
- centralized handling of creation and removal of trigger sysfs
attributes via attribute group
- addition of module_led_trigger() helper
The other things that need to be mentioned:
New features and improvements to existing LED class drivers:
- lt3593: add DT support, switch to gpiod interface
- lm3692x: support LED sync configuration, change OF calls to fwnode
calls
- apu: modify PC Engines apu/apu2 driver to support apu3
Change in the drivers/net/can/led.c:
- mark led trigger as broken since it's in the way for the further
cleanups. It implements a subset of the netdev trigger and an Ack
is needed from someone who can actually test and confirm that the
netdev trigger works for can devices"
* tag 'leds-for-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds: (32 commits)
leds: ns2: Change unsigned to unsigned int
usb: simplify usbport trigger
leds: gpio trigger: simplifications from core changes
leds: backlight trigger: simplifications from core changes
leds: activity trigger: simplifications from core changes
leds: default-on trigger: make use of module_led_trigger()
leds: heartbeat trigger: simplifications from core changes
leds: oneshot trigger: simplifications from core changes
leds: transient trigger: simplifications from core changes
leds: timer trigger: simplifications from core changes
leds: netdev trigger: simplifications from core changes
leds: triggers: new function led_set_trigger_data()
leds: triggers: define module_led_trigger helper
leds: triggers: handle .trigger_data and .activated() in the core
leds: triggers: add device attribute support
leds: triggers: let struct led_trigger::activate() return an error code
leds: triggers: make the MODULE_LICENSE string match the actual license
leds: lm3692x: Support LED sync configuration
dt: bindings: lm3692x: Update binding for LED sync control
leds: lm3692x: Change DT calls to fwnode calls
...
The TXQ teardown code can reference the vif data structures that are
stored in the netdev private memory area if there are still packets on
the queue when it is being freed. Since the TXQ teardown code is run
after the netdevs are freed, this can lead to a use-after-free. Fix this
by moving the TXQ teardown code to earlier in ieee80211_unregister_hw().
Reported-by: Ben Greear <greearb@candelatech.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Shaul Triebitz