After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM everywhere under
drivers/iio/.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Set the threshold to low by default. With this thresholds any movement
on the device with this sensor will generate event.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Change event spec direction from
IIO_EV_DIR_RISING | IIO_EV_DIR_FALLING
to
IIO_EV_DIR_EITHER
Suggested-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This chip is capable to identify motion across x, y and z axes. So
send different events.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When mode set fails due to some transient failures, it will atleast
reset the state of runtime usage count and also let the runtime
suspend retry from the driver framework.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The following chips are either similar or have only the resolution
different. Hence, change this driver to support these chips too:
BMI055 - combo chip (accelerometer part is identical to BMC150's)
BMA255 - identical to BMC150's accelerometer
BMA222E - 8 bit resolution
BMA250E - 10 bit resolution
BMA280 - 14 bit resolution
Additionally:
* add bmc150_accel_match_acpi_device() function to check that the device
has been enumerated through ACPI;
* rename bmc150_accel_acpi_gpio_probe() to bmc150_accel_gpio_probe()
since the ACPI matching has been moved to the new function. Also, this
will allow for the GPIO matching to be done against a device tree too, not only
ACPI tree;
* rename bmc150_scale_info struct member 'range' to 'reg_range' to be
consistent with the naming convention used elsewhere in the driver
and declare it u8, instead of int;
* change CONFIG description to list all supported chips;
Signed-off-by: Laurentiu Palcu <laurentiu.palcu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When CONFIG_PM_RUNTIME is not set, the following issues are seen:
* warning message at compilation time:
warning: 'bmc150_accel_get_startup_times' defined but not used [-Wunused-function]
* bmc150_accel_set_power_state() will always fail and reading the
accelerometer data is impossible;
This occurs because of the call to pm_runtime_put_autosuspend calls
__pm_runtime_suspend which returns -ENOSYS.
This commit fixes these.
Signed-off-by: Laurentiu Palcu <laurentiu.palcu@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
According to documentation ([1] - page 27), the range for 16G is
7.81mg/LSB. Converted to SI, this is:
7.81 * 10^-3 * 9.80665 m/s^2 / LSB = 0.0765899365 m/s^2 / LSB
[1] http://ae-bst.resource.bosch.com/media/products/dokumente/bmc150/BST-BMC150-DS000-04.pdf
Signed-off-by: Laurentiu Palcu <laurentiu.palcu@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This change implements BMC150 accelerometer driver. A BMC150 package
consist of a compass and an accelerometer. This driver only implements
accelerometer part.
Spec downloaded from:
http://ae-bst.resource.bosch.com/media/products/dokumente/bmc150/BST-BMC150-DS000-03.pdf
This sensor chip supports many advanced features, but this driver
implements minimum feature set which is a must to be useful.
This driver can be enhanced incrementally.
If the sensor vendor wants to update full featured version, they
can substitute or enhance this driver when they get chance.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Rafael J. Wysocki