Other Plantronics headset models seem requiring the same workaround as
C320-M to add the 20ms delay for the control messages, too. Apply the
workaround generically for devices with the vendor ID 0x047f.
Note that the problem didn't surface before 5.11 just with luck.
Since 5.11 got a big code rewrite about the stream handling, the
parameter setup procedure has changed, and this seemed triggering the
problem more often.
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1182552
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210304085009.4770-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Rear audio on Lenovo ThinkStation P620 stops working after commit
1965c4364b ("ALSA: usb-audio: Disable autosuspend for Lenovo
ThinkStation P620"):
[ 6.013526] usbcore: registered new interface driver snd-usb-audio
[ 6.023064] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x0, type = 1
[ 6.023083] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x202, wIndex = 0x0, type = 4
[ 6.023090] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x0, type = 1
[ 6.023098] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x202, wIndex = 0x0, type = 4
[ 6.023103] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x0, type = 1
[ 6.023110] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x202, wIndex = 0x0, type = 4
[ 6.045846] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x0, type = 1
[ 6.045866] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x202, wIndex = 0x0, type = 4
[ 6.045877] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x0, type = 1
[ 6.045886] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x202, wIndex = 0x0, type = 4
[ 6.045894] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x0, type = 1
[ 6.045908] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x202, wIndex = 0x0, type = 4
I overlooked the issue because when I was working on the said commit,
only the front audio is tested. Apology for that.
Changing supports_autosuspend in driver is too late for disabling
autosuspend, because it was already used by USB probe routine, so it can
break the balance on the following code that depends on
supports_autosuspend.
Fix it by using usb_disable_autosuspend() helper, and balance the
suspend count in disconnect callback.
Fixes: 1965c4364b ("ALSA: usb-audio: Disable autosuspend for Lenovo ThinkStation P620")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210304043419.287191-1-kai.heng.feng@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit only contains the fix about the `URB_CONTROL` request
direction to set the samplerate of Pioneer DJM devices (`URB_CONTROL out`).
Fixes: 3b85f5fc75 ("ALSA: usb-audio: Add DJM450 to Pioneer format quirk")
Signed-off-by: Nicolas MURE <nicolas.mure2019@gmail.com>
Link: https://lore.kernel.org/r/20210301142927.14552-1-nicolas.mure2019@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Like the DJM-750, ensure that the format control message is passed to
the device when opening a stream. It seems as though fmt->sync_ep is not
always set when this function is called hence the passing of the value
at the call site. If this can be fixed, fmt->sync_up should be used as
the wvalue.
There doesn't seem to be a "cpu_to_le24" type function defined hence for
the open code but I did see a similar thing done in Bluez lib. Perhaps
we can get these definitions defined in byteorder.h. See hci_cpu_to_le24
in include/net/bluetooth/hci.h:2543 for similar usage.
Signed-off-by: Olivia Mackintosh <livvy@base.nu>
Link: https://lore.kernel.org/r/20210202134225.3217-2-livvy@base.nu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current sample rate setup function for UAC1 assumes only the first
endpoint retrieved from the interface:altset pair, but the rate set up
may be needed also for the secondary endpoint. Also, retrieving the
endpoint number from the interface descriptor is redundant; we have
already the target endpoint in the given audioformat object.
This patch simplifies the code and corrects the target endpoint as
described in the above. It simply refers to fmt->endpoint directly.
Also, this patch drops the pioneer_djm_set_format_quirk() that is
caleld from snd_usb_set_format_quirk(); this function does the sample
rate setup but for the capture endpoint (0x82), and that's exactly
what the change above fixes.
Link: https://lore.kernel.org/r/20210118075816.25068-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are devices that have multiple endpoints sharing the same
iface/altset not only for sync but also for the actual streams, and
the audioformat for such an endpoint needs to be handled with the
proper endpoint index; otherwise it confuses the endpoint management.
This patch extends the audioformat to annotate the endpoint index, and
put the proper ep_idx=1 to Pioneer device quirk entries accordingly.
Fixes: bf6313a0ff ("ALSA: usb-audio: Refactor endpoint management")
Link: https://lore.kernel.org/r/20210108075219.21463-5-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent change in the endpoint management moved the endpoint object
creation from the stream open time to the parser of the audio
descriptor. It works fine for the standard audio, but it overlooked
the other places that create audio streams via quirks
(QUIRK_AUDIO_FIXED_ENDPOINT) like the reported a few Pioneer devices;
those call snd_usb_add_audio_stream() manually, hence they miss the
endpoints, eventually resulting in the error at opening streams.
Moreover, now the sync EP setup was moved to the explicit call of
snd_usb_audioformat_set_sync_ep(), and this needs to be added for
those places, too.
This patch addresses those regressions for quirks. It adds a local
helper function add_audio_stream_from_fixed_fmt(), which does the all
needed tasks, and replaces the calls of snd_usb_add_audio_stream()
with this new function.
Fixes: 54cb31901b ("ALSA: usb-audio: Create endpoint objects at parsing phase")
Reported-by: František Kučera <konference@frantovo.cz>
Link: https://lore.kernel.org/r/20210108075219.21463-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now that the usb audio driver correctly finds implicit feedback endpoints,
the implicit feedback quirk for the MOTU M-Series is no longer required.
This also removes some unnecessary vendor specific messages from the MOTU
M-Series boot quirk. The removed vendor specific messages turned on vendor
specific interrupts to the host every 32 samples. The only thing the boot
quirk needs to do is wait for 2 seconds.
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Signed-off-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-42-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some fields like interface and alt_idx in snd_usb_substream are mostly
useless now as they can be referred via either cur_audiofmt or
data_endpoint assigned to the substream. Drop those, and also assure
the concurrency about the access of cur_audiofmt field.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-31-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The audioformat is referred in many places but most of usages are
read-only. Let's add const prefix in the possible places.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-28-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit 92adc96f8e ("ALSA: usb-audio: set the interface format
after resume on Dell WD19") introduced the workaround for the broken
setup after the resume specifically on a Dell dock model. However,
the full setup should have been performed after the resume on all
devices, as we can't guarantee the same state. So this patch removes
the conditional check and applies the workaround always.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-24-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A preliminary change for the later big changes. This is a minor code
refactoring to drop the unnecessary arguments that can be retrieved in
a different way.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-21-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A preliminary change for the later big changes. This is a minor code
refactoring to drop the unnecessary arguments that can be retrieved in
a different way.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-20-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A preliminary patch for the later big change. Just a minor code
refactoring.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-19-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Found one more Logitech device, BCC950 ConferenceCam, which needs
the same delay here. This makes 3 out of 3 devices I have tried.
Therefore, add a delay for all Logitech devices as it does not hurt.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Cc: <stable@vger.kernel.org> # 4.19.y, 5.4.y
Link: https://lore.kernel.org/r/20201117122803.24310-1-joakim.tjernlund@infinera.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Khadas audio devices ( USB_ID_VENDOR 0x3353 )
have DSD-capable implementations from XMOS
need add new usb vendor id for recognition
Signed-off-by: Artem Lapkin <art@khadas.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201103103311.5435-1-art@khadas.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A USB device will always haev a bi-directional endpoint 0, that's just
how the devices work, so no need to check for that in a few quirk tests
as it will always pass.
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Alexander Tsoy <alexander@tsoy.me>
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200914153756.3412156-12-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
snd_usb_pipe_sanity_check() is a great function, so let's move it into
the USB core so that other parts of the kernel, including the USB core,
can call it.
Name it usb_pipe_type_check() to match the existing
usb_urb_ep_type_check() call, which now uses this function.
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Cc: Eli Billauer <eli.billauer@gmail.com>
Cc: Emiliano Ingrassia <ingrassia@epigenesys.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Alexander Tsoy <alexander@tsoy.me>
Cc: "Geoffrey D. Bennett" <g@b4.vu>
Cc: Jussi Laako <jussi@sonarnerd.net>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Dmitry Panchenko <dmitry@d-systems.ee>
Cc: Chris Wulff <crwulff@gmail.com>
Cc: Jesus Ramos <jesus-ramos@live.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200914153756.3412156-2-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch extends support for DJM-250MK2 and allows recording.
However, DVS is not possible yet (see the comment in code).
Signed-off-by: František Kučera <franta-linux@frantovo.cz>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200825153113.6352-1-konference@frantovo.cz
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If USB autosuspend is enabled, both front and rear panel can no longer
detect jack insertion.
Enable USB remote wakeup, i.e. needs_remote_wakeup = 1, doesn't help
either.
So disable USB autosuspend to prevent missing jack detection event.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20200823105854.26950-1-kai.heng.feng@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Further investigation of the L-R swap problem on the MS2109 reveals that
the problem isn't that the channels are swapped, but rather that they
are swapped and also out of phase by one sample. In other words, the
issue is actually that the very first frame that comes from the hardware
is a half-frame containing only the right channel, and after that
everything becomes offset.
So introduce a new quirk field to drop the very first 2 bytes that come
in after the format is configured and a capture stream starts. This puts
the channels in phase and in the correct order.
Cc: stable@vger.kernel.org
Signed-off-by: Hector Martin <marcan@marcan.st>
Link: https://lore.kernel.org/r/20200810082400.225858-1-marcan@marcan.st
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We've found Samsung USBC Headset (AKG) (VID: 0x04e8, PID: 0xa051)
need a tiny delay after each class compliant request.
Otherwise the device might not be able to be recognized each times.
Signed-off-by: Chihhao Chen <chihhao.chen@mediatek.com>
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1592910203-24035-1-git-send-email-macpaul.lin@mediatek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Similar to the Kingston HyperX AMP, the Kingston HyperX Cloud
Alpha S (0951:0x16ea) uses two interfaces, but only the second
interface contains the capture stream. This patch delays the
registration until the second interface appears.
Signed-off-by: Christoffer Nielsen <cn@obviux.dk>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/CAOtG2YHOM3zy+ed9KS-J4HkZo_QGzcUG9MigSp4e4_-13r6B=Q@mail.gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
fix error "clock source 41 is not valid, cannot use"
[] New USB device found, idVendor=154e, idProduct=1002, bcdDevice= 1.00
[] New USB device strings: Mfr=1, Product=2, SerialNumber=0
[] Product: DCD-1500RE
[] Manufacturer: D & M Holdings Inc.
[]
[] clock source 41 is not valid, cannot use
[] usbcore: registered new interface driver snd-usb-audio
Signed-off-by: Yick W. Tse <y_w_tse@yahoo.com.hk>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1373857985.210365.1592048406997@mail.yahoo.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pioneer DJ DJM-900NXS2 is a widely used DJ mixer with 2 audio USB
interfaces. Both have a MIDI controller, 10 playback and 12 capture
channels. Audio endpoints are vendor-specific and 3 files need to be
patched. All playback and capture channels work fine with all supported
sample rates (44.1k, 48k, 96k). Patches are attached.
Signed-off-by: Dmitry Panchenko <dmitry@d-systems.ee>
Link: https://lore.kernel.org/r/48ab19ff-3303-9bf8-ed0e-bcb31d8537eb@d-systems.ee
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Due to rounding error driver sometimes incorrectly calculate next packet
size, which results in audible clicks on devices with synchronous playback
endpoints. For example on a high speed bus and a sample rate 44.1 kHz it
loses one sample every ~40.9 seconds. Fortunately playback interface on
Scarlett 2i4 2nd gen has a working explicit feedback endpoint, so we can
switch playback data endpoint to asynchronous mode as a workaround.
Signed-off-by: Alexander Tsoy <alexander@tsoy.me>
Link: https://lore.kernel.org/r/20200421190908.462860-1-alexander@tsoy.me
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Force it to use asynchronous playback.
Same quirk has already been added for Focusrite Scarlett Solo (2nd gen)
with a commit 46f5710f0b ("ALSA: usb-audio: Add quirk for Focusrite
Scarlett Solo").
This also seems to prevent regular clicks when playing at 44100Hz
on Scarlett 2i2 (2nd gen). I did not notice any side effects.
Moved both quirks to snd_usb_audioformat_attributes_quirk() as suggested.
Signed-off-by: Gregor Pintar <grpintar@gmail.com>
Reviewed-by: Alexander Tsoy <alexander@tsoy.me>
Link: https://lore.kernel.org/r/20200420214030.2361-1-grpintar@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Similar to the Kingston HyperX AMP, the Kingston HyperX Cloud
Alpha S (0951:16d8) uses two interfaces, but only the second
interface contains the capture stream. This patch delays the
registration until the second interface appears.
Signed-off-by: Emmanuel Pescosta <emmanuelpescosta099@gmail.com>
Link: https://lore.kernel.org/r/20200404153843.9288-1-emmanuelpescosta099@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A slight refactoring of the registration quirk code. Now it uses the
table lookup for easy additions in future. Also the return type was
changed to bool, and got a few more comments.
Link: https://lore.kernel.org/r/20200325103322.2508-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Create a quirk that allows special processing and/or
skipping the call to snd_card_register.
For HyperX AMP, which uses two interfaces, but only has
a capture stream in the second, this allows the capture
stream to merge with the first PCM.
Signed-off-by: Chris Wulff <crwulff@gmail.com>
Link: https://lore.kernel.org/r/20200314165449.4086-3-crwulff@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
MicroBook IIc operates in UAC2 mode by default. This patch addresses
several issues with it:
- MicroBook II and IIc shares the same USB ID. We can distinguish them
by interface class.
- MaxPacketsOnly attribute is erroneously set in endpoint descriptors.
As a result this card produces noise with all sample rates other than
96 KHz. This also causes issues like IOMMU page faults and other
problems with host controller.
- Sample rate changes takes more than 2 seconds for this device. Clock
validity request returns false during that period, so the clock validity
quirk is required.
Signed-off-by: Alexander Tsoy <alexander@tsoy.me>
Link: https://lore.kernel.org/r/20200229151815.14199-1-alexander@tsoy.me
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merging the UAC2 effect unit parser improvement. As it's based on the
previous usb-audio driver fix, it was deviated from for-next branch.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds support for Presonus Studio 1810c, a usb interface
that's UAC2 compliant with a few quirks and a few extra hw-specific
controls. I've tested all 3 altsettings and the added switch
controls and they work as expected.
More infos on the card:
https://www.presonus.com/products/Studio-1810c
Note that this work is based on packet inspection with
usbmon. I just wanted to get this card to work for using
it on our open-source radio station:
https://github.com/UoC-Radio
v2 address issues reported by Takashi:
* Properly get/set enum type controls
* Prevent race condition on switch_get/set
* Various control naming changes
* Various coding style fixes
v3 improve readability of sample rate filtering
and some other minor changes.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Link: https://lore.kernel.org/r/5e47481a.1c69fb81.befb3.8dac@mx.google.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Audioengine D1 (0x2912:0x30c8) does support reading the sample rate,
but it returns the rate in byte-reversed order.
When setting sampling rate, the driver produces these warning messages:
[168840.944226] usb 3-2.2: current rate 4500480 is different from the runtime rate 44100
[168854.930414] usb 3-2.2: current rate 8436480 is different from the runtime rate 48000
[168905.185825] usb 3-2.1.2: current rate 30465 is different from the runtime rate 96000
As can be seen from the hexadecimal conversion, the current rate read
back is byte-reversed from the rate that was set.
44100 == 0x00ac44, 4500480 == 0x44ac00
48000 == 0x00bb80, 8436480 == 0x80bb00
96000 == 0x017700, 30465 == 0x007701
Rather than implementing a new quirk to reverse the order, just skip
checking the rate to avoid spamming the log.
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200211162235.1639889-1-nivedita@alum.mit.edu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add delay to make sure that audio urbs are not sent too early.
Otherwise the device hangs. Windows driver makes ~2s delay, so use
about the same time delay value.
snd_usb_apply_boot_quirk() is called 3 times for my MOTU M4, which
is an overkill. Thus a quirk that is called only once is implemented.
Also send two vendor-specific control messages before and after
the delay. This behaviour is blindly copied from the Windows driver.
Signed-off-by: Alexander Tsoy <alexander@tsoy.me>
Link: https://lore.kernel.org/r/20200112102358.18085-1-alexander@tsoy.me
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For consistency reason, make all hex numbers with lower alphabets for
USB ID entries. It improves grep-ability and reduces careless
mistakes.
Link: https://lore.kernel.org/r/20200105081900.21870-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Recently we found the headset-mic on the Dell Dock WD19 doesn't work
anymore after s3 (s2i or deep), this problem could be workarounded by
closing (pcm_close) the app and then reopening (pcm_open) the app, so
this bug is not easy to be detected by users.
When problem happens, retire_capture_urb() could still be called
periodically, but the size of captured data is always 0, it could be
a firmware bug on the dock. Anyway I found after resuming, the
snd_usb_pcm_prepare() will be called, and if we forcibly run
set_format() to set the interface and its endpoint, the capture
size will be normal again. This problem and workaound also apply to
playback.
To fix it in the kernel, add a quirk to let set_format() run
forcibly once after resume.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191218132650.6303-1-hui.wang@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit 60849562a5 ("ALSA: usb-audio: Fix possible NULL
dereference at create_yamaha_midi_quirk()") added NULL checks in
create_yamaha_midi_quirk(), but there was an overlook. The code
allows one of either injd or outjd is NULL, but the second if check
made returning -ENODEV if any of them is NULL. Fix it in a proper
form.
Fixes: 60849562a5 ("ALSA: usb-audio: Fix possible NULL dereference at create_yamaha_midi_quirk()")
Reported-by: Pavel Machek <pavel@denx.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191113111259.24123-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai