When iterating over the entries in firmware_features_table we only need
to go over the actual number of entries in the array instead of declaring
it to be bigger and checking to make sure there is a valid entry in every
slot.
This patch removes the FIRMWARE_MAX_FEATURES #define and replaces the
array looping with the use of ARRAY_SIZE().
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently we search for the best_energy hcall using a custom function. Move
this to using the firmware_feature_table.
Signed-off-by: Michael Neuling <mikey@neuling.org>
cc: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
cc: Linux PPC dev <linuxppc-dev@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This allows firmware_features_table names to add a '*' at the end so that only
partial strings are matched.
When a '*' is added, only upto the '*' is matched when setting firmware feature
bits.
This is useful for the matching best energy feature.
Signed-off-by: Michael Neuling <mikey@neuling.org>
cc: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
cc: Linux PPC dev <linuxppc-dev@ozlabs.org>
Reviewed-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This new hcall in POWER8 is used to set various resource mode registers.
eg. it can set address translation mode on interrupt (note: partition wide
scope)
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This simple patch adds the firmware feature for VPHN to the firmware
features bitmask.
Signed-off-by: Jesse Larrew <jlarrew@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Profiling of a page fault scalability microbenchmark shows flush_hash_range
is not calling the batch hpte invalidate hcall (H_BULK_REMOVE).
It turns out we have a duplicate firmware feature for hcall-bulk and the
current setup code stops after finding the first match. This meant we never
batch and always do individual invalidates.
The patch below removes the duplicate and shifts FW_FEATURE_CMO to close
the gap. With the patch applied the single threaded page fault rate improves
from 217169 to 238755 per second on a POWER5 test box, a 10% improvement.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The declaration for fw_feature_init() is in pseries.h and
implemented in firmware.c, so the latter should include the
former.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a DEBUG config setting which turns on all (most) of the debugging
under platforms/pseries.
To have this take effect we need to remove all the #undef DEBUG's, in
various files. We leave the #undef DEBUG in platforms/pseries/lpar.c,
as this enables debugging printks from the low-level hash table routines,
and tends to make your system unusable. If you want those enabled you
still have to turn them on by hand.
Also some of the RAS code has a DEBUG block which causes a functional
change, so I've keyed this off a different (non-existant) debug #define.
This is only enabled if you have PPC_EARLY_DEBUG enabled also.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In pseries/lpar.c, fix some printf specifier mismatches, and add
a newline to one printk.
In pseries/rtasd.c add "rtasd" to some messages to make it clear
where they're coming from.
In pseries/scanlog.c remove the hand-rolled runtime debugging support
in there. This file has been largely unchanged for eons, if we need to
debug it in future we can recompile.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes the error
error: implicit declaration of function "udbg_printf"
We have a few spots where we reference udbg_printf() without #including
udbg.h. These are within #ifdef DEBUG blocks, so unnoticed until we do
a #define DEBUG or #define DEBUG_LOW nearby.
Signed-off-by: Will Schmidt <will_schmidt@vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move firmware feature initialisation from pSeries_init_early to the
earlier pSeries_probe_hypertas so they are initialised before firmware
feature fixups are applied.
Currently firmware feature sections are only used for iSeries which
initialises the these features much earlier. This is a bug in waiting
on pSeries.
Also adds some whitespace fixups.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The previous patch changing pSeries to use H_BULK_REMOVE broke the
JS20 blade, where the firmware doesn't support H_BULK_REMOVE. This
adds a firmware check so that on machines that don't have H_BULK_REMOVE,
we just use the H_REMOVE call as before.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now that get_property() returns a void *, there's no need to cast its
return value. Also, treat the return value as const, so we can
constify get_property later.
pseries platform changes.
Built for pseries_defconfig
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We need to export ppc64_firmware_features for modules. Before we do that
I think we should probably rename it to powerpc_firmware_features.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently we have some stuff in firmware.h and kernel/firmware.c that is
#ifdef CONFIG_PPC_PSERIES. Move it all into platforms/pseries.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Nathan Fontenot