The struct fsl_ifc_mtd is allocated with devm_kzalloc, so its memory
is "managed" automatically by the kernel. That is, we do not need to
free it explicitly; it will be freed when the device is removed. And we
*certainly* shouldn't free it with a regular kfree().
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
in/out_be32 accessors are Power arch centric whereas
ioread/writebe32 are available in other arches.
Since the IFC device registers are annotated big endian in
fsl_ifc.h, the accessor annotations now match, resulting in the
pleasant side-effect of this patch silencing sparse endian
warnings such as the following:
drivers/mtd/nand/fsl_ifc_nand.c:179:19: warning: incorrect type in argument 1 (different base types)
drivers/mtd/nand/fsl_ifc_nand.c:179:19: expected unsigned int volatile [noderef] [usertype] <asn:2>*addr
drivers/mtd/nand/fsl_ifc_nand.c:179:19: got restricted __be32 [noderef] <asn:2>*<noident>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
IFC_FIR_OP_CMD0 issues command for execution without checking flash
readiness. It may cause problem if flash is not ready. Instead use
IFC_FIR_OP_CW0 which Wait for tWB time and poll R/B to return high or
time-out, before issuing command.
NAND_CMD_READID command implemention does not fulfill above requirement. So
update its programming.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Hemant Nautiyal <hemant.nautiyal@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Just as Artem suggested:
"Both UBI and JFFS2 are able to read verify what they wrote already.
There are also MTD tests which do this verification. So I think there
is no reason to keep this in the NAND layer, let alone wasting RAM in
the driver to support this feature. Besides, it does not work for sub-pages
and many drivers have it broken. It hurts more than it provides benefits."
So kill MTD_NAND_VERIFY_WRITE entirely.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
IFC-1.1.0 uses 28nm techenology for SRAM. This tech has known limitaion for
SRAM i.e. "byte select" is not supported. Hence Read Modify Write is
implemented in IFC for any "system side write" into sram buffer. Reading an
uninitialized memory results in ECC Error from sram wrapper.
Hence we must initialize/prefill SRAM buffer by any data before writing
anything in SRAM from system side. To initialize SRAM user can use "READID"
NAND command with read bytes equal to SRAM size. It will be a one time
activity post boot.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There is an implemention of hardware ECC write page function which may return an
error indication.
For instance, using Atmel HW PMECC to write one page into a nand flash, the hardware
engine will compute the BCH ecc code for this page. so we need read a the
status register to theck whether the ecc code is generated.
But we cannot assume the status register always can be ready, for example,
incorrect hardware configuration or hardware issue, in such case we need
write_page() to return a error code.
Since the definition of 'write_page' function in struct nand_ecc_ctrl is 'void'.
So this patch will:
1. add return 'int' value for 'write_page' function.
2. to be consitent, add return 'int' value for 'write_page_raw' fuctions too.
3. add code to test the return value, and if negative, indicate an
error happend when write page with ECC.
4. fix the compile warning in all impacted nand flash driver.
Note: I couldn't compile-test all of these easily, as some had ARCH dependencies.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
According to its documentation, the NAND_NO_READRDY option is always used
when autoincrement is not supported. Autoincrement support was recently
dropped, so we can drop this options as well (defaulting to "no read ready
check").
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Don't read OOB if the caller doesn't require it.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
New NAND controllers can perform read/write via HW engines which don't expose
OOB data in their DMA mode. To reflect this, we should rework the nand_chip /
nand_ecc_ctrl interfaces that assume that drivers will always read/write OOB
data in the nand_chip.oob_poi buffer. A better interface includes a boolean
argument that explicitly tells the callee when OOB data is requested by the
calling layer (for reading/writing to/from nand_chip.oob_poi).
This patch adds the 'oob_required' parameter to each relevant {read,write}_page
interface; all 'oob_required' parameters are left unused for now. The next
patch will set the parameter properly in the nand_base.c callers, and follow-up
patches will make use of 'oob_required' in some of the callee functions.
Note that currently, there is no harm in ignoring the 'oob_required' parameter
and *always* utilizing nand_chip.oob_poi, but there can be
performance/complexity/design benefits from avoiding filling oob_poi in the
common case. I will try to implement this for some drivers which can be ported
easily.
Note: I couldn't compile-test all of these easily, as some had ARCH
dependencies.
[dwmw2: Merge later 1/0 vs. true/false cleanup]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: Jiandong Zheng <jdzheng@broadcom.com>
Acked-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
No drivers use auto-increment NAND, so kill the NO_AUTOINCR option entirely.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The ecc.read_page() method for nand drivers is changed to return the maximum
number of bitflips that were corrected on any one region covering an ecc step,
This patch doesn't change what the nand code returns to mtd.
This v2 includes the change to the fsl_ifc_nand driver requested by Scott¹.
¹ http://lists.infradead.org/pipermail/linux-mtd/2012-April/040883.html
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Acked-by (freescale changes): Scott Wood <scottwood@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This fixes a couple of ecc strength values for which I earlier made conservative
guesses, but whose correct values were later determined¹ (thanks Ivan). Also
sets strength for fsl_ifc_nand, which was merged to mainline after the original
patch that set the strength for all drivers.
¹ http://lists.infradead.org/pipermail/linux-mtd/2012-March/040325.html
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Integrated Flash Controller(IFC) can be used to hook NAND Flash
chips using NAND Flash Machine available on it.
Signed-off-by: Dipen Dudhat <Dipen.Dudhat@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Liu Shuo <b35362@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Brian Norris