With some net devices types, an IPv6 address configured while the
interface was down can stay 'tentative' forever, even after the interface
is set up. In some case, pending IPv6 DADs are not executed when the
device becomes ready.
I observed this while doing some tests with kvm. If I assign an IPv6
address to my interface eth0 (kvm driver rtl8139) when it is still down
then the address is flagged tentative (IFA_F_TENTATIVE). Then, I set
eth0 up, and to my surprise, the address stays 'tentative', no DAD is
executed and the address can't be pinged.
I also observed the same behaviour, without kvm, with virtual interfaces
types macvlan and veth.
Some easy steps to reproduce the issue with macvlan:
1. ip link add link eth0 type macvlan
2. ip -6 addr add 2003::ab32/64 dev macvlan0
3. ip addr show dev macvlan0
...
inet6 2003::ab32/64 scope global tentative
...
4. ip link set macvlan0 up
5. ip addr show dev macvlan0
...
inet6 2003::ab32/64 scope global tentative
...
Address is still tentative
I think there's a bug in net/ipv6/addrconf.c, addrconf_notify():
addrconf_dad_run() is not always run when the interface is flagged IF_READY.
Currently it is only run when receiving NETDEV_CHANGE event. Looks like
some (virtual) devices doesn't send this event when becoming up.
For both NETDEV_UP and NETDEV_CHANGE events, when the interface becomes
ready, run_pending should be set to 1. Patch below.
'run_pending = 1' could be moved below the if/else block but it makes
the code less readable.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix printk format warnings in net/9p.
Built cleanly on 7 arches.
net/9p/client.c:820: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'u64'
net/9p/client.c:820: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'u64'
net/9p/client.c:867: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'u64'
net/9p/client.c:867: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'u64'
net/9p/client.c:932: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'u64'
net/9p/client.c:932: warning: format '%llx' expects type 'long long unsigned int', but argument 6 has type 'u64'
net/9p/client.c:982: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'u64'
net/9p/client.c:982: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'u64'
net/9p/client.c:1025: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'u64'
net/9p/client.c:1025: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'u64'
net/9p/client.c:1227: warning: format '%llx' expects type 'long long unsigned int', but argument 7 has type 'u64'
net/9p/client.c:1227: warning: format '%llx' expects type 'long long unsigned int', but argument 12 has type 'u64'
net/9p/client.c:1227: warning: format '%llx' expects type 'long long unsigned int', but argument 8 has type 'u64'
net/9p/client.c:1227: warning: format '%llx' expects type 'long long unsigned int', but argument 13 has type 'u64'
net/9p/client.c:1252: warning: format '%llx' expects type 'long long unsigned int', but argument 7 has type 'u64'
net/9p/client.c:1252: warning: format '%llx' expects type 'long long unsigned int', but argument 12 has type 'u64'
net/9p/client.c:1252: warning: format '%llx' expects type 'long long unsigned int', but argument 8 has type 'u64'
net/9p/client.c:1252: warning: format '%llx' expects type 'long long unsigned int', but argument 13 has type 'u64'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The changes to deliver hardware accelerated VLAN packets to packet
sockets (commit bc1d0411) caused a warning for non-NAPI drivers.
The __vlan_hwaccel_rx() function is called directly from the drivers
RX function, for non-NAPI drivers that means its still in RX IRQ
context:
[ 27.779463] ------------[ cut here ]------------
[ 27.779509] WARNING: at kernel/softirq.c:136 local_bh_enable+0x37/0x81()
...
[ 27.782520] [<c0264755>] netif_nit_deliver+0x5b/0x75
[ 27.782590] [<c02bba83>] __vlan_hwaccel_rx+0x79/0x162
[ 27.782664] [<f8851c1d>] atl1_intr+0x9a9/0xa7c [atl1]
[ 27.782738] [<c0155b17>] handle_IRQ_event+0x23/0x51
[ 27.782808] [<c015692e>] handle_edge_irq+0xc2/0x102
[ 27.782878] [<c0105fd5>] do_IRQ+0x4d/0x64
Split hardware accelerated VLAN reception into two parts to fix this:
- __vlan_hwaccel_rx just stores the VLAN TCI and performs the VLAN
device lookup, then calls netif_receive_skb()/netif_rx()
- vlan_hwaccel_do_receive(), which is invoked by netif_receive_skb()
in softirq context, performs the real reception and delivery to
packet sockets.
Reported-and-tested-by: Ramon Casellas <ramon.casellas@cttc.es>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
While adding MIGRATE support to strongSwan, Andreas Steffen noticed that
the selectors provided in XFRM_MSG_ACQUIRE have their family field
uninitialized (those in MIGRATE do have their family set).
Looking at the code, this is because the af-specific init_tempsel()
(called via afinfo->init_tempsel() in xfrm_init_tempsel()) do not set
the value.
Reported-by: Andreas Steffen <andreas.steffen@strongswan.org>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
xfrm: Fix xfrm_policy_gc_lock handling.
niu: Use pci_ioremap_bar().
bnx2x: Version Update
bnx2x: Calling netif_carrier_off at the end of the probe
bnx2x: PCI configuration bug on big-endian
bnx2x: Removing the PMF indication when unloading
mv643xx_eth: fix SMI bus access timeouts
net: kconfig cleanup
fs_enet: fix polling
XFRM: copy_to_user_kmaddress() reports local address twice
SMC91x: Fix compilation on some platforms.
udp: Fix the SNMP counter of UDP_MIB_INERRORS
udp: Fix the SNMP counter of UDP_MIB_INDATAGRAMS
drivers/net/smc911x.c: Fix lockdep warning on xmit.
From: Alexey Dobriyan <adobriyan@gmail.com>
Based upon a lockdep trace by Simon Arlott.
xfrm_policy_kill() can be called from both BH and
non-BH contexts, so we have to grab xfrm_policy_gc_lock
with BH disabling.
Signed-off-by: David S. Miller <davem@davemloft.net>
While adding support for MIGRATE/KMADDRESS in strongSwan (as specified
in draft-ebalard-mext-pfkey-enhanced-migrate-00), Andreas Steffen
noticed that XFRMA_KMADDRESS attribute passed to userland contains the
local address twice (remote provides local address instead of remote
one).
This bug in copy_to_user_kmaddress() affects only key managers that use
native XFRM interface (key managers that use PF_KEY are not affected).
For the record, the bug was in the initial changeset I posted which
added support for KMADDRESS (13c1d18931
'xfrm: MIGRATE enhancements (draft-ebalard-mext-pfkey-enhanced-migrate)').
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Reported-by: Andreas Steffen <andreas.steffen@strongswan.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
UDP packets received in udpv6_recvmsg() are not only IPv6 UDP packets, but
also have IPv4 UDP packets, so when do the counter of UDP_MIB_INERRORS in
udpv6_recvmsg(), we should check whether the packet is a IPv6 UDP packet
or a IPv4 UDP packet.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If UDP echo is sent to xinetd/echo-dgram, the UDP reply will be received
at the sender. But the SNMP counter of UDP_MIB_INDATAGRAMS will be not
increased, UDP6_MIB_INDATAGRAMS will be increased instead.
Endpoint A Endpoint B
UDP Echo request ----------->
(IPv4, Dst port=7)
<---------- UDP Echo Reply
(IPv4, Src port=7)
This bug is come from this patch cb75994ec3.
It do counter UDP[6]_MIB_INDATAGRAMS until udp[v6]_recvmsg. Because
xinetd used IPv6 socket to receive UDP messages, thus, when received
UDP packet, the UDP6_MIB_INDATAGRAMS will be increased in function
udpv6_recvmsg() even if the packet is a IPv4 UDP packet.
This patch fixed the problem.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (33 commits)
af_unix: netns: fix problem of return value
IRDA: remove double inclusion of module.h
udp: multicast packets need to check namespace
net: add documentation for skb recycling
key: fix setkey(8) policy set breakage
bpa10x: free sk_buff with kfree_skb
xfrm: do not leak ESRCH to user space
net: Really remove all of LOOPBACK_TSO code.
netfilter: nf_conntrack_proto_gre: switch to register_pernet_gen_subsys()
netns: add register_pernet_gen_subsys/unregister_pernet_gen_subsys
net: delete excess kernel-doc notation
pppoe: Fix socket leak.
gianfar: Don't reset TBI<->SerDes link if it's already up
gianfar: Fix race in TBI/SerDes configuration
at91_ether: request/free GPIO for PHY interrupt
amd8111e: fix dma_free_coherent context
atl1: fix vlan tag regression
SMC91x: delete unused local variable "lp"
myri10ge: fix stop/go mmio ordering
bonding: fix panic when taking bond interface down before removing module
...
fix problem of return value
net/unix/af_unix.c: unix_net_init()
when error appears, it should return 'error', not always return 0.
Signed-off-by: Jianjun Kong <jianjun@zeuux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current UDP multicast delivery is not namespace aware.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Acked-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 04a4bb55bc ("net: add
skb_recycle_check() to enable netdriver skb recycling") added a
method for network drivers to recycle skbuffs, but while use of
this mechanism was documented in the commit message, it should
really have been added as a docbook comment as well -- this
patch does that.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As it is, all instances of ->release() for files that have ->fasync()
need to remember to evict file from fasync lists; forgetting that
creates a hole and we actually have a bunch that *does* forget.
So let's keep our lives simple - let __fput() check FASYNC in
file->f_flags and call ->fasync() there if it's been set. And lose that
crap in ->release() instances - leaving it there is still valid, but we
don't have to bother anymore.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I noticed that, under certain conditions, ESRCH can be leaked from the
xfrm layer to user space through sys_connect. In particular, this seems
to happen reliably when the kernel fails to resolve a template either
because the AF_KEY receive buffer being used by racoon is full or
because the SA entry we are trying to use is in XFRM_STATE_EXPIRED
state.
However, since this could be a transient issue it could be argued that
EAGAIN would be more appropriate. Besides this error code is not even
documented in the man page for sys_connect (as of man-pages 3.07).
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
register_pernet_gen_device() can't be used is nf_conntrack_pptp module is
also used (compiled in or loaded).
Right now, proto_gre_net_exit() is called before nf_conntrack_pptp_net_exit().
The former shutdowns and frees GRE piece of netns, however the latter
absolutely needs it to flush keymap. Oops is inevitable.
Switch to shiny new register_pernet_gen_subsys() to get correct ordering in
netns ops list.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
netns ops which are registered with register_pernet_gen_device() are
shutdown strictly before those which are registered with
register_pernet_subsys(). Sometimes this leads to opposite (read: buggy)
shutdown ordering between two modules.
Add register_pernet_gen_subsys()/unregister_pernet_gen_subsys() for modules
which aren't elite enough for entry in struct net, and which can't use
register_pernet_gen_device(). PPTP conntracking module is such one.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
SUNRPC: Fix potential race in put_rpccred()
SUNRPC: Fix rpcauth_prune_expired
NFS: Convert nfs_attr_generation_counter into an atomic_long
SUNRPC: Respond promptly to server TCP resets
Enable netlabel auditing functions only when CONFIG_AUDIT is set
Signed-off-by: Manish Katiyar <mkatiyar@gmail.com>
Signed-off-by: Paul Moore <paul.moore@hp.com>
Fix the compiler warnings below, thanks to Andrew Morton for finding them.
net/netlabel/netlabel_mgmt.c: In function `netlbl_mgmt_listentry':
net/netlabel/netlabel_mgmt.c:268: warning: 'ret_val' might be used
uninitialized in this function
Signed-off-by: Paul Moore <paul.moore@hp.com>
when testing the new pktgen module with multiple queues and ixgbe with:
pgset "flag QUEUE_MAP_CPU"
I found that I was getting errors in dmesg like:
pktgen: WARNING: QUEUE_MAP_CPU disabled because CPU count (8) exceeds number
<4>pktgen: WARNING: of tx queues (8) on eth15
you'll note, 8 really doesn't exceed 8.
This patch seemed to fix the logic errors and also the attempts at
limiting line length in printk (which didn't work anyway)
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have to be careful when we try to unhash the credential in
put_rpccred(), because we're not holding the credcache lock, so the call to
rpcauth_unhash_cred() may fail if someone else has looked the cred up, and
obtained a reference to it.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
We need to make sure that we don't remove creds from the cred_unused list
if they are still under the moratorium, or else they will never get
garbage collected.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
If the server sends us an RST error while we're in the TCP_ESTABLISHED
state, then that will not result in a state change, and so the RPC client
ends up hanging forever (see
http://bugzilla.kernel.org/show_bug.cgi?id=11154)
We can intercept the reset by setting up an sk->sk_error_report callback,
which will then allow us to initiate a proper shutdown and retry...
We also make sure that if the send request receives an ECONNRESET, then we
shutdown too...
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Initialise correctly last fields, so tasks can be actually executed.
On some architectures the initial jiffies value is not zero, so later
all rfkill incorrectly decides that rfkill_*.last is in future.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
David Miller noticed that commit
33ad798c92 '(tcp: options clean up')
did not move the req->cookie_ts check.
This essentially disabled commit 4dfc281702
'[Syncookies]: Add support for TCP options via timestamps.'.
This restores the original logic.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a potential error packet loop.
Signed-off-by: Remi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The default for the regulatory compatibility option is wrong;
if you picked the default you ended up with a non-functional wifi
system (at least I did on Fedora 9 with iwl4965).
I don't think even the October 2008 releases of the various distros
has the new userland so clearly the default is wrong, and also
we can't just go about deleting this in 2.6.29...
Change the default to "y" and also adjust the config text a little to
reflect this.
This patch fixes regression #11859
With thanks to Johannes Berg for the diagnostics
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (29 commits)
tcp: Restore ordering of TCP options for the sake of inter-operability
net: Fix disjunct computation of netdev features
sctp: Fix to handle SHUTDOWN in SHUTDOWN_RECEIVED state
sctp: Fix to handle SHUTDOWN in SHUTDOWN-PENDING state
sctp: Add check for the TSN field of the SHUTDOWN chunk
sctp: Drop ICMP packet too big message with MTU larger than current PMTU
p54: enable 2.4/5GHz spectrum by eeprom bits.
orinoco: reduce stack usage in firmware download path
ath5k: fix suspend-related oops on rmmod
[netdrvr] fec_mpc52xx: Implement polling, to make netconsole work.
qlge: Fix MSI/legacy single interrupt bug.
smc911x: Make the driver safer on SMP
smc911x: Add IRQ polarity configuration
smc911x: Allow Kconfig dependency on ARM
sis190: add identifier for Atheros AR8021 PHY
8139x: reduce message severity on driver overlap
igb: add IGB_DCA instead of selecting INTEL_IOATDMA
igb: fix tx data corruption with transition to L0s on 82575
ehea: Fix memory hotplug support
netdev: DM9000: remove BLACKFIN hacking in DM9000 netdev driver
...
This is not our bug! Sadly some devices cannot cope with the change
of TCP option ordering which was a result of the recent rewrite of
the option code (not that there was some particular reason steming
from the rewrite for the reordering) though any ordering of TCP
options is perfectly legal. Thus we restore the original ordering
to allow interoperability with/through such broken devices and add
some warning about this trap. Since the reordering just happened
without any particular reason, this change shouldn't cost us
anything.
There are already couple of known failure reports (within close
proximity of the last release), so the problem might be more
wide-spread than a single device. And other reports which may
be due to the same problem though the symptoms were less obvious.
Analysis of one of the case revealed (with very high probability)
that sack capability cannot be negotiated as the first option
(SYN never got a response).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Reported-by: Aldo Maggi <sentiniate@tiscali.it>
Tested-by: Aldo Maggi <sentiniate@tiscali.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'v28-range-hrtimers-for-linus-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (37 commits)
hrtimers: add missing docbook comments to struct hrtimer
hrtimers: simplify hrtimer_peek_ahead_timers()
hrtimers: fix docbook comments
DECLARE_PER_CPU needs linux/percpu.h
hrtimers: fix typo
rangetimers: fix the bug reported by Ingo for real
rangetimer: fix BUG_ON reported by Ingo
rangetimer: fix x86 build failure for the !HRTIMERS case
select: fix alpha OSF wrapper
select: fix alpha OSF wrapper
hrtimer: peek at the timer queue just before going idle
hrtimer: make the futex() system call use the per process slack value
hrtimer: make the nanosleep() syscall use the per process slack
hrtimer: fix signed/unsigned bug in slack estimator
hrtimer: show the timer ranges in /proc/timer_list
hrtimer: incorporate feedback from Peter Zijlstra
hrtimer: add a hrtimer_start_range() function
hrtimer: another build fix
hrtimer: fix build bug found by Ingo
hrtimer: make select() and poll() use the hrtimer range feature
...
My change
commit e2a6b85247
net: Enable TSO if supported by at least one device
didn't do what was intended because the netdev_compute_features
function was designed for conjunctions. So what happened was that
it would simply take the TSO status of the last constituent device.
This patch extends it to support both conjunctions and disjunctions
under the new name of netdev_increment_features.
It also adds a new function netdev_fix_features which does the
sanity checking that usually occurs upon registration. This ensures
that the computation doesn't result in an illegal combination
since this checking is absent when the change is initiated via
ethtool.
The two users of netdev_compute_features have been converted.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Once an endpoint has reached the SHUTDOWN-RECEIVED state,
it MUST NOT send a SHUTDOWN in response to a ULP request.
The Cumulative TSN Ack of the received SHUTDOWN chunk
MUST be processed.
This patch fix to process Cumulative TSN Ack of the received
SHUTDOWN chunk in SHUTDOWN_RECEIVED state.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If SHUTDOWN is received in SHUTDOWN-PENDING state, enpoint should enter
the SHUTDOWN-RECEIVED state and check the Cumulative TSN Ack field of
the SHUTDOWN chunk (RFC 4960 Section 9.2). If the SHUTDOWN chunk can
acknowledge all of the send DATA chunks, SHUTDOWN-ACK should be sent.
But now endpoint just silently discarded the SHUTDOWN chunk.
SHUTDOWN received in SHUTDOWN-PENDING state can happend when the last
SACK is lost by network, or the SHUTDOWN chunk can acknowledge all of
the received DATA chunks. The packet sequence(SACK lost) is like this:
Endpoint A Endpoint B ULP
(ESTABLISHED) (ESTABLISHED)
<----------- DATA
<--- shutdown
Enter SHUTDOWN-PENDING state
SACK ----lost---->
SHUTDOWN(*1) ------------>
<----------- SHUTDOWN-ACK
(*1) silently discarded now.
This patch fix to handle SHUTDOWN in SHUTDOWN-PENDING state as the same
as ESTABLISHED state.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If SHUTDOWN chunk is received Cumulative TSN Ack beyond the max tsn currently
send, SHUTDOWN chunk be accepted and the association will be broken. New data
is send, but after received SACK it will be drop because TSN in SACK is less
than the Cumulative TSN, data will be retrans again and again even if correct
SACK is received.
The packet sequence is like this:
Endpoint A Endpoint B ULP
(ESTABLISHED) (ESTABLISHED)
<----------- DATA (TSN=x-1)
<----------- DATA (TSN=x)
SHUTDOWN -----------> (Now Cumulative TSN=x+1000)
(TSN=x+1000)
<----------- DATA (TSN=x+1)
SACK -----------> drop the SACK
(TSN=x+1)
<----------- DATA (TSN=x+1)(retrans)
This patch fix this problem by terminating the association and respond to
the sender with an ABORT.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If ICMP packet too big message is received with MTU larger than current
PMTU, SCTP will still accept this ICMP message and sync the PMTU of assoc
with the wrong MTU.
Endpoing A Endpoint B
(ESTABLISHED) (ESTABLISHED)
ICMP --------->
(packet too big, MTU too larger)
sync PMTU
This patch fixed the problem by drop that ICMP message.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several sparse warnings were introduced by patches accepted during the merge
window which weren't caught. This patch fixes those warnings.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
This patch implements the RDMA transport provider for 9P. It allows
mounts to be performed over iWARP and IB capable network interfaces.
Signed-off-by: Tom Tucker <tom@opengridcomputing.com>
Signed-off-by: Latchesar Ionkov <lionkov@lanl.gov>
Fixes build problem with 9p when building with debug disabled.
Also contains some fixes for warnings which pop up when
CONFIG_NET_9P_DEBUG is disabled.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
While looking for the recent "sack issue" I also read all eff_sacks
usage that was played around by some relevant commit. I found
out that there's another thing that is asking for a fix (unrelated
to the "sack issue" though).
This feature has probably very little significance in practice.
Opposite direction timeout with bidirectional tcp comes to me as
the most likely scenario though there might be other cases as
well related to non-data segments we send (e.g., response to the
opposite direction segment). Also some ACK losses or option space
wasted for other purposes is necessary to prevent the earlier
SACK feedback getting to the sender.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs: (26 commits)
9p: add more conservative locking
9p: fix oops in protocol stat parsing error path.
9p: fix device file handling
9p: Improve debug support
9p: eliminate depricated conv functions
9p: rework client code to use new protocol support functions
9p: remove unnecessary tag field from p9_req_t structure
9p: remove 9p fcall debug prints
9p: add new protocol support code
9p: encapsulate version function
9p: move dirread to fs layer
9p: adjust 9p vfs write operation
9p: move readn meta-function from client to fs layer
9p: consolidate read/write functions
9p: drop broken unused error path from p9_conn_create()
9p: make rpc code common and rework flush code
9p: use the rcall structure passed in the request in trans_fd read_work
9p: apply common request code to trans_fd
9p: apply common tagpool handling to trans_fd
9p: move request management to client code
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
netfilter: replace old NF_ARP calls with NFPROTO_ARP
netfilter: fix compilation error with NAT=n
netfilter: xt_recent: use proc_create_data()
netfilter: snmp nat leaks memory in case of failure
netfilter: xt_iprange: fix range inversion match
netfilter: netns: use NFPROTO_NUMPROTO instead of NUMPROTO for tables array
netfilter: ctnetlink: remove obsolete NAT dependency from Kconfig
pkt_sched: sch_generic: Fix oops in sch_teql
dccp: Port redirection support for DCCP
tcp: Fix IPv6 fallout from 'Port redirection support for TCP'
netdev: change name dropping error codes
ipvs: Update CONFIG_IP_VS_IPV6 description and help text
(Supplements: ee999d8b95)
NFPROTO_ARP actually has a different value from NF_ARP, so ensure all
callers use the new value so that packets _do_ get delivered to the
registered hooks.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the compilation of ctnetlink when the NAT support
is not enabled.
/home/benh/kernels/linux-powerpc/net/netfilter/nf_conntrack_netlink.c:819: warning: enum nf_nat_manip_type\u2019 declared inside parameter list
/home/benh/kernels/linux-powerpc/net/netfilter/nf_conntrack_netlink.c:819: warning: its scope is only this definition or declaration, which is probably not what you want
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reported by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Inverted IPv4 v1 and IPv6 v0 matches don't match anything since 2.6.25-rc1!
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that ctnetlink doesn't have any NAT module depenencies anymore,
we can also remove them from Kconfig.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
After these commands:
# modprobe sch_teql
# tc qdisc add dev eth0 root teql0
# tc qdisc del dev eth0 root
we get an oops in teql_destroy() when spin_lock is taken from a null
qdisc_sleeping pointer. It's because at the moment teql0 dev haven't
been activated yet, and a qdisc_root_sleeping() is pointing to noop
qdisc's netdev_queue with qdisc_sleeping uninitialized. This patch
fixes this both for noop and noqueue netdev_queues to avoid similar
problems in the future.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a3116ac5c2 from 1st October ("tcp: Port
redirection support for TCP") broke DCCP skb lookup by changing inet_csk_clone,
which is used by DCCP to generate the child socket after the handshake.
This patch updates DCCP to use 'loc_port' instead of 'sport', which fixes the
problem, and thus inheriting port redirection support via the new interface.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: KOVACS Krisztian <hidden@sch.bme.hu>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'tcp: Port redirection support for TCP' (a3116ac5c) added a new member
to inet_request_sock() which inet_csk_clone() makes use of but failed
to add proper initialization to the IPv6 syncookie code and missed a
couple of places where the new member should be used instead of
inet_sk(sk)->sport.
Signed-off-by: KOVACS Krisztian <hidden@sch.bme.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
If changename notifier returns an error code, it gets incorrectly
cleared during rollback so the error is never returned to the user.
Found while testing similar code for MTU changes.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a URL to further info to the CONFIG_IP_VS_IPV6 Kconfig help
text. Also, I think it should be ok to remove the "DANGEROUS" label in the
description line at this point to get people to try it out and find all
the bugs ;) It's still marked as experimental, of course.
Signed-off-by: Julius Volz <juliusv@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the reorganization some of the multi-theaded locking assumptions were
accidently relaxed. This patch moves us back towards a more conservative
locking strategy.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
When we get an error on parsing a stat due to a protocol bug,
we can generate an oops during cleanup because we didn't
initialize the string pointers in the stat structure.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
The new debug support lacks some of the information that the previous fcprint
code provided -- this patch focuses on better presentation of debug data along
with more helpful debug along error paths.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Remove depricated conv functions which have been replaced with new
protocol routines.
This patch also reworks the one instance of the file-system code which
directly calls conversion routines (to accomplish unpacking dirreads).
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Now that the new protocol functions are in place, this patch switches
the client code to using the new support code.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
One of the current debug options allows users to get a verbose dump of fcalls.
This isn't really necessary as correctly parsed protocol frames can be printed
as part of the code in the client functions. The consolidated printfcalls
structure would require new entries to be added for every extension. This
patch removes the debug print methods and their use.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
This adds a new protocol processing support code based on Anthony Liguori's
9p library code. This code performs protocol marshalling/unmarshalling using
printf like strings to represent protocol elements. It is my intent to use
them to replace the current functions in conv.c as well as the
p9_create_* functions.
This should make the client implementation much more clear, and also make it
much easier to add new protocol extensions by limiting the number of places
in which changes need to be made.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Alsmot all 9P client wire functions have their own (set of) functions.
Tversion is an exception as its encapsulated into the client_create code.
This patch moves the protocol specifics of this to a function to match the
rest of the code.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Currently reading a directory is implemented in the client code.
This function is not actually a wire operation, but a meta operation
which calls read operations and processes the results.
This patch moves this functionality to the fs layer and calls component
wire operations instead of constructing their packets. This provides a
cleaner separation and will help when we reorganize the client functions
and protocol processing methods.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
There are a couple of methods in the client code which aren't actually
wire operations. To keep things organized cleaner, these operations are
being moved to the fs layer.
This patch moves the readn meta-function (which executes multiple wire
reads until a buffer is full) to the fs layer.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Currently there are two separate versions of read and write. One for
dealing with user buffers and the other for dealing with kernel buffers.
There is a tremendous amount of code duplication in the otherwise
identical versions of these functions. This patch adds an additional
user buffer parameter to read and write and conditionalizes handling of
the buffer on whether the kernel buffer or the user buffer is populated.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Post p9_fd_poll() error path which checks m->poll_waddr[i] for PTR_ERR
value has the following problems.
* It's completely unused. Error value is set iff NULL @wait_address
has been specified to p9_pollwait() which is guaranteed not to
happen.
* It dereferences @m after deallocating it (introduced by 571ffeaf and
spotted by Raja R Harinath.
* It returned the wrong value on error. It should return
poll_waddr[i] but it returnes poll_waddr (introduced by 571ffeaf).
* p9_mux_poll_stop() doesn't handle PTR_ERR value. It will try to
operate on the PTR_ERR value as if it's a normal pointer and cause
oops.
As the error path is bogus in the first place, there's no reason to
hold onto it. Kill it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Raja R Harinath <harinath@hurrynot.org>
This code moves the rpc function to the common client base,
reorganizes the flush code to be more simple and stable, and
makes the necessary adjustments to the underlying transports
to adapt to the new structure.
This reduces the overall amount of code duplication between the
transports and should make adding new transports more straightforward.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
This patch reworks the read_work function to enable it to directly use a passed
in rcall structure. This should help allow us to remove unnecessary copies
in the future.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
The virtio transport uses a simplified request management system
that I want to use for all transports. This patch adapts and moves the
exisiting code for managing requests to the client common code.
Later patches will apply these mechanisms to the other transports.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
The current trans_fd rpc mechanisms use a dynamic callback mechanism which
introduces a lot of complexity which only accomodates a single special case.
This patch removes much of that complexity in favor of a simple exception
mechanism to deal with flushes.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Currently, trans_fd has two structures (p9_req and p9_mux-rpc)
which contain mostly duplicate data.
This patch consolidates these two structures and removes p9_mux_rpc.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Cleanup files by reordering functions in order to remove need for
unnecessary function prototypes.
There are no code changes here, just functions being moved around and
prototypes being eliminated.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Now that we are passing client state into the transport modules, remove
duplicate state which is present in transport private structures.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Right now there is a transport module structure which provides per-transport
type functions and data and a transport structure which contains per-instance
public data as well as function pointers to instance specific functions.
This patch moves public transport visible instance data to the client
structure (which in some cases had duplicate data) and consolidates the
functions into the transport module structure.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
trans_fd used pool of upto 100 pollers to monitor the r/w fds. The
approach makes sense in userspace back when the only available
interfaces were poll(2) and select(2). As each event monitor -
trigger - handling iteration took O(n) where `n' is the number of
watched fds, it makes sense to spread them to many pollers such that
the `n' can be divided by the number of pollers. However, this
doesn't make any sense in kernel because persistent edge triggered
event monitoring is how the whole thing is implemented in the kernel
in the first place.
This patch converts trans_fd to use single poller which watches all
the fds instead of the poll of pollers approach. All the fds are
registered for monitoring on creation and only the fds with pending
events are scanned when something happens much like how epoll is
implemented.
This change makes trans_fd fd monitoring more efficient and simpler.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
net: Remove CONFIG_KMOD from net/ (towards removing CONFIG_KMOD entirely)
ipv4: Add a missing rcu_assign_pointer() in routing cache.
[netdrvr] ibmtr: PCMCIA IBMTR is ok on 64bit
xen-netfront: Avoid unaligned accesses to IP header
lmc: copy_*_user under spinlock
[netdrvr] myri10ge, ixgbe: remove broken select INTEL_IOATDMA
* git://git.linux-nfs.org/projects/trondmy/nfs-2.6: (53 commits)
NFS: Fix a resolution problem with nfs_inode->cache_change_attribute
NFS: Fix the resolution problem with nfs_inode_attrs_need_update()
NFS: Changes to inode->i_nlinks must set the NFS_INO_INVALID_ATTR flag
RPC/RDMA: ensure connection attempt is complete before signalling.
RPC/RDMA: correct the reconnect timer backoff
RPC/RDMA: optionally emit useful transport info upon connect/disconnect.
RPC/RDMA: reformat a debug printk to keep lines together.
RPC/RDMA: harden connection logic against missing/late rdma_cm upcalls.
RPC/RDMA: fix connect/reconnect resource leak.
RPC/RDMA: return a consistent error, when connect fails.
RPC/RDMA: adhere to protocol for unpadded client trailing write chunks.
RPC/RDMA: avoid an oops due to disconnect racing with async upcalls.
RPC/RDMA: maintain the RPC task bytes-sent statistic.
RPC/RDMA: suppress retransmit on RPC/RDMA clients.
RPC/RDMA: fix connection IRD/ORD setting
RPC/RDMA: support FRMR client memory registration.
RPC/RDMA: check selected memory registration mode at runtime.
RPC/RDMA: add data types and new FRMR memory registration enum.
RPC/RDMA: refactor the inline memory registration code.
NFS: fix nfs_parse_ip_address() corner case
...
Some code here depends on CONFIG_KMOD to not try to load
protocol modules or similar, replace by CONFIG_MODULES
where more than just request_module depends on CONFIG_KMOD
and and also use try_then_request_module in ebtables.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
rt_intern_hash() is doing an update of a RCU guarded hash chain
without using rcu_assign_pointer() or equivalent barrier.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (46 commits)
UIO: Fix mapping of logical and virtual memory
UIO: add automata sercos3 pci card support
UIO: Change driver name of uio_pdrv
UIO: Add alignment warnings for uio-mem
Driver core: add bus_sort_breadthfirst() function
NET: convert the phy_device file to use bus_find_device_by_name
kobject: Cleanup kobject_rename and !CONFIG_SYSFS
kobject: Fix kobject_rename and !CONFIG_SYSFS
sysfs: Make dir and name args to sysfs_notify() const
platform: add new device registration helper
sysfs: use ilookup5() instead of ilookup5_nowait()
PNP: create device attributes via default device attributes
Driver core: make bus_find_device_by_name() more robust
usb: turn dev_warn+WARN_ON combos into dev_WARN
debug: use dev_WARN() rather than WARN_ON() in device_pm_add()
debug: Introduce a dev_WARN() function
sysfs: fix deadlock
device model: Do a quickcheck for driver binding before doing an expensive check
Driver core: Fix cleanup in device_create_vargs().
Driver core: Clarify device cleanup.
...
name and nlen parameters passed to ->strategy hook are unused, remove
them. In general ->strategy hook should know what it's doing, and don't
do something tricky for which, say, pointer to original userspace array
may be needed (name).
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net> [ networking bits ]
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Danny ter Haar <dth@cistron.nl>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Base infrastructure to enable per-module debug messages.
I've introduced CONFIG_DYNAMIC_PRINTK_DEBUG, which when enabled centralizes
control of debugging statements on a per-module basis in one /proc file,
currently, <debugfs>/dynamic_printk/modules. When, CONFIG_DYNAMIC_PRINTK_DEBUG,
is not set, debugging statements can still be enabled as before, often by
defining 'DEBUG' for the proper compilation unit. Thus, this patch set has no
affect when CONFIG_DYNAMIC_PRINTK_DEBUG is not set.
The infrastructure currently ties into all pr_debug() and dev_dbg() calls. That
is, if CONFIG_DYNAMIC_PRINTK_DEBUG is set, all pr_debug() and dev_dbg() calls
can be dynamically enabled/disabled on a per-module basis.
Future plans include extending this functionality to subsystems, that define
their own debug levels and flags.
Usage:
Dynamic debugging is controlled by the debugfs file,
<debugfs>/dynamic_printk/modules. This file contains a list of the modules that
can be enabled. The format of the file is as follows:
<module_name> <enabled=0/1>
.
.
.
<module_name> : Name of the module in which the debug call resides
<enabled=0/1> : whether the messages are enabled or not
For example:
snd_hda_intel enabled=0
fixup enabled=1
driver enabled=0
Enable a module:
$echo "set enabled=1 <module_name>" > dynamic_printk/modules
Disable a module:
$echo "set enabled=0 <module_name>" > dynamic_printk/modules
Enable all modules:
$echo "set enabled=1 all" > dynamic_printk/modules
Disable all modules:
$echo "set enabled=0 all" > dynamic_printk/modules
Finally, passing "dynamic_printk" at the command line enables
debugging for all modules. This mode can be turned off via the above
disable command.
[gkh: minor cleanups and tweaks to make the build work quietly]
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use offsetof() instead of home-brewed version.
Based upon initial patch by Steven Whitehouse and suggestions
by Ben Hutchings.
Signed-off-by: David S. Miller <davem@davemloft.net>
Problem observed:
In IPv6, in the presence of multiple routers candidates to
default gateway in one segment, each sending a different
value of preference, the Linux hosts connected to the
segment weren't selecting the right one in all the
combinations possible of LOW/MEDIUM/HIGH preference.
This patch changes two files:
include/linux/icmpv6.h
Get the "router_pref" bitfield in the right place
(as RFC4191 says), named the bit left with this fix as
"home_agent" (RFC3775 say that's his function)
net/ipv6/ndisc.c
Corrects the binary logic behind the updating of the
router preference in the flags of the routing table
Result:
With this two fixes applied, the default route used by
the system was to consistent with the rules mentioned
in RFC4191 in case of changes in the value of preference
in router advertisements
Signed-off-by: Pedro Ribeiro <pribeiro@net.ipl.pt>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Dobriyan