If some bits in a pin Pull-Up control register (PUPR) control pin
pull-down instead of pin pull-up, there are two pinmux_bias_reg entries:
a first one with the puen field filled in, listing pins with pull-up
functionality, and a second one with the pud field filled in, listing
pins with pull-down functionality. On encountering the second entry,
where puen is NULL, the for-loop terminates early, causing the remaining
bias registers not to be checked. In addition, sh_pfc_check_bias_reg()
does not handle such entries.
Fix this by treating pinmux_bias_reg.puen and pinmux_bias_reg.pud the
same.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/29526d06fa223cffd785cdb264b756a202b11cea.1633615652.git.geert+renesas@glider.be
The GENMASK(h, l) macro creates a contiguous bitmask starting at bit
position @l and ending at position @h, inclusive.
This did not trigger any error checks, as the individual register fields
cover at most 3 of the 4 available bits.
Fixes: 08df16e07a ("pinctrl: sh-pfc: checker: Add drive strength register checks")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/8f82d6147fbe3367d4c83962480e97f58d9c96a2.1633615652.git.geert+renesas@glider.be
If some bits in a pin Pull-Up control register (PUPR) control pin
pull-down instead of pin pull-up, there are two pinmux_bias_reg entries:
a first one with the puen field filled in, listing pins with pull-up
functionality, and a second one with the pud field filled in, listing
pins with pull-down functionality. On encountering the second entry,
where puen is NULL, the for-loop terminates early, causing the remaining
bias registers not to be saved/restored during PSCI system suspend.
Fortunately this does not trigger on any supported system yet, as PSCI
is only used on R-Car Gen3 and RZ/G2 systems, which all have separate
pin Pull-Enable (PUEN) and pin Pull-Up/Down control (PUD) registers.
Avoid this ever becoming a problem by treating pinmux_bias_reg.puen and
pinmux_bias_reg.pud the same. Note that a register controlling both
pull-up and pull-down pins would be saved and restored twice, which is
harmless.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/59d2fbddff685b6a7a82ff17d2b37633e30e8860.1633615652.git.geert+renesas@glider.be
Remove the duplicate port register 22h and replace it with missing port
register 21h.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20210922074140.22178-1-biju.das.jz@bp.renesas.com
Fixes: c4c4637eb5 ("pinctrl: renesas: Add RZ/G2L pin and gpio controller driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Global static variables don't need to be initialized to 0, because the
compiler will initialize them.
Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Link: https://lore.kernel.org/r/20210906134040.96642-1-wangborong@cdjrlc.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add support for pin and gpio controller driver for RZ/G2L SoC.
Based on a patch in the BSP by Hien Huynh <hien.huynh.px@renesas.com>.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20210727112328.18809-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
As R-Car H3 ES1.x (R8A77950) and R-Car ES2.0+ (R8A77951) use the same
compatible value, the pin control driver relies on soc_device_match()
with soc_id = "r8a7795" and the (non)matching of revision = "ES1.*" to
match with and distinguish between the two SoC variants. The
corresponding entries in the normal of_match_table are present only to
make the optional sanity checks work.
The R-Car H3e-2G (R8A779M1) SoC is a different grading of the R-Car H3
ES3.0 (R8A77951) SoC. It uses the same compatible values for individual
devices, but has an additional compatible value for the root node.
When running on an R-Car H3e-2G SoC, soc_device_match() with soc_id =
"r8a7795" does not return a match. Hence the pin control driver falls
back to the normal of_match_table, and, as the R8A77950 entry is listed
first, incorrectly uses the sub-driver for R-Car H3 ES1.x.
Fix this by moving the entry for R8A77951 before the entry for R8A77950.
Simplify sh_pfc_quirk_match() to only handle R-Car H3 ES1,x, as R-Car H3
ES2.0+ can now be matched using the normal of_match_table as well.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/6cdc5bfa424461105779b56f455387e03560cf66.1626707688.git.geert+renesas@glider.be
Implement support for pull-up (most pins, excl. DU_DOTCLKIN0) and
pull-down (most pins, excl. JTAG) handling for the R-Car D3 SoC, using
some parts from the common R-Car bias handling, which requires making
rcar_pin_to_bias_reg() public.
R-Car D3 needs special handling for the NFRE# (GP_3_0) and NFWE#
(GP_3_1) pins. Unlike all other pins, they are controlled by different
bits in the LSI pin pull-up/down control register (PUD2) than in the LSI
pin pull-enable register (PUEN2).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/04aad2b0bf82a32fb08e5e21e4ac1fb03452724f.1625064076.git.geert+renesas@glider.be
When disabling pin bias, there is no need to touch the LSI pin
pull-up/down control register (PUDn), which selects between pull-up and
pull-down. Just disabling the pull-up/down function through the LSI pin
pull-enable register (PUENn) is sufficient.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/071ec644de2555da593a4531ef5d3e4d79cf997d.1625064076.git.geert+renesas@glider.be
Implement support for pull-up (most pins, excl. DU_DOTCLKIN and EXTALR)
and pull-down (most pins, excl. JTAG) handling for the R-Car V3M SoC,
using the common R-Car bias handling.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/bcfad447624d874258a45a92554574b8fe9f712f.1619785375.git.geert+renesas@glider.be
Implement support for pull-up (most pins) and pull-down (ASEBRK#/ACK)
handling for R-Car E2 and RZ/G1E SoCs, using the common R-Car bias
handling.
Note that on RZ/G1E, the "ASEBRK#/ACK" pin is called "ACK", but the code
doesn't handle that naming difference. Hence users should use the R-Car
naming in DTS files.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/f78da2ba937ce98ae9196f4ee54149a5214fd545.1619785375.git.geert+renesas@glider.be
Implement support for pull-up (most pins) and pull-down (EDBGREQ)
handling for the R-Car V2H SoC, using the common R-Car bias handling.
Note that the R-Car V2H Hardware User's Manual Rev. 1.00 says that
the LSI Pin Pull-Up Control Register 11 (PUPR11) controls pull-ups for
the {SCK,WS,SDATA}[01] pins. These are assumed to be typos, as R-Car
V2H has only Serial Sound Interface channels 3 and 4.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/48d2abdd63ee43ed99cb32ed4a5f4d76ba563162.1619785375.git.geert+renesas@glider.be
Implement support for pull-up (most pins) and pull-down (ASEBRK#/ACK)
handling for R-Car H2 and RZ/G1H SoCs, using the common R-Car bias
handling.
Note that on RZ/G1H, the "ASEBRK#/ACK" pin is called "ACK", but the code
doesn't handle that naming difference. Hence users should use the R-Car
naming in DTS files.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/dde6e0b36a4e4494039a3466df208b5ec5c594ee.1619785375.git.geert+renesas@glider.be
Implement support for pull-up (most pins) and pull-down (ASEBRK#/ACK)
handling for the RZ/G1C SoC, using the common R-Car bias handling.
Note that on RZ/G1C, the "ASEBRK#/ACK" pin is called "ACK", but the code
doesn't handle that naming difference. Hence users should use the R-Car
naming in DTS files.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/18c8ebf9fa9e239253a723857e9dffeec775db7e.1619785375.git.geert+renesas@glider.be
Change whitespace in the pin control drivers for R-Car H3 ES2.0+, R-Car
M3-W/M3-W+, and R-Car M3-N, to reduce the differences among these very
similar drivers.
These changes have no functional impact.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/527b45ebfc664a80e41cb0136677db7260e11437.1619785375.git.geert+renesas@glider.be
R-Car Gen3 Hardware Manual Errata for Rev. 0.52 of Nov 30, 2016, added
the configuration bit for bias pull-down control for the PRESET# pin on
R-Car M3-W. Add driver support for controlling pull-down on this pin.
Fixes: 2d40bd2427 ("pinctrl: sh-pfc: r8a7796: Add bias pinconf support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/c479de5b3f235c2f7d5faea9e7e08e6fccb135df.1619785375.git.geert+renesas@glider.be
Implement support for pull-up (most pins) and pull-down (ASEBRK#/ACK)
handling for R-Car M2-W and M2-N, and RZ/G1M and RZ/G1N SoCs, using the
common R-Car bias handling.
Note that on RZ/G1 SoCs, the "ASEBRK#/ACK" pin is called "ACK", but the
code doesn't handle that naming difference. Hence users should use the
R-Car naming in DTS files.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20210303132619.3938128-7-geert+renesas@glider.be
Currently, the common R-Car bias handling supports pin controllers with
either:
1. Separate pin Pull-Enable (PUEN) and pin Pull-Up/Down control (PUD)
registers, for controlling both pin pull-up and pin pull-down,
2. A single pin Pull-Up control register (PUPR), for controlling pin
pull-up.
Add support for a variant of #2, where some bits in the single pin
Pull-Up control register (PUPR) control pin pull-down instead of pin
pull-up. This is the case for the "ASEBRK#/ACK" pin on R-Car M2-W,
M2-N, and E2, and the "ACK" pin on RZ/G1M, RZ/G1N, RZ/G1E, and RZ/G1C.
To describe such a register, SoC-specific drivers need to provide two
instances of pinmux_bias_reg: a first one with the puen field filled in,
listing pins with pull-up functionality, and a second one with the pud
field filled in, listing pins with pull-down functionality.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20210303132619.3938128-6-geert+renesas@glider.be
Add PORT_GP_CFG_7() and PORT_GP_7() helper macros, to be used by the
r8a7791 subdriver.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20210303132619.3938128-5-geert+renesas@glider.be
The pin control sub-drivers for SH/R-Mobile SoCs contain almost
identical bias handling. The only SoC-specific part is the mapping from
pin numbers to PORTnCR registers.
Reduce code duplication by factoring out the bias handling to the common
pinctrl.c code. Use a callback to handle the pin/register mapping.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20210303132619.3938128-4-geert+renesas@glider.be
The Renesas Pin Function Controller driver uses two header files:
- sh_pfc.h, for use by both core code and SoC-specific drivers,
- core.h, for internal use by the core code only.
Hence move the R-Car bias helper declarations from core.h to sh_pfc.h,
and drop the inclusion of core.h from SoC-specific drivers that no
longer need it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20210303132619.3938128-3-geert+renesas@glider.be
Now all R-Car pin control drivers have been converted to the common
R-Car bias handling, sh_pfc_pin_to_bias_reg() is only called from a
single place. Move it from core.c to pinctrl.c, make it static, and
rename it to rcar_pin_to_bias_reg(), as it is specific to R-Car SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20210303132619.3938128-2-geert+renesas@glider.be
- Restrict debug runtime-checks to Renesas platforms,
- Initial support for the R-Car V3U SoC.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCYAFgRQAKCRCKwlD9ZEnx
cEWIAP40TrUerqfnQgJ7iNYLh9WfSk48w9Gxzm92E7FanXaJBAD/dmkieXwQBBig
zKNuoWL2ZlK7O5MMkzpNnhLNS95SEQs=
=vIxg
-----END PGP SIGNATURE-----
Merge tag 'renesas-pinctrl-for-v5.12-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: renesas: Updates for v5.12
- Restrict debug runtime-checks to Renesas platforms,
- Initial support for the R-Car V3U SoC.
Add pins, groups and functions for the 16-Bit Timer Pulse Unit outputs
on the R-Car R8A779A0 (V3U) SoC.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Link: https://lore.kernel.org/r/20210112165929.31002-13-uli+renesas@fpond.eu
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add pins, groups, and function for the Interrupt Controller for External
Devices (INTC-EX) on the R-Car R8A779A0 (V3U) SoC.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Link: https://lore.kernel.org/r/20210112165929.31002-7-uli+renesas@fpond.eu
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds HSCIF0-3 pins, groups and functions to the R8A779A0
(V3U) SoC.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210112165929.31002-6-uli+renesas@fpond.eu
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds groups and function for AVB PHY, LINK, MAGIC, RGMII and
PTP pins for the R8A779A0 (V3U) SoC.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210112165929.31002-3-uli+renesas@fpond.eu
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds I2C0-6 pins, groups and functions to the R8A779A0 (V3U)
SoC.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210112165929.31002-2-uli+renesas@fpond.eu
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds SCIF0, 1, 3 and 4 pins, groups and functions for the
R8A779A0 (V3U) SoC.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210112165912.30876-6-uli+renesas@fpond.eu
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds initial pinctrl support for the R8A779A0 (V3U) SoC,
including bias, drive strength and voltage control.
Based on patch by LUU HOAI <hoai.luu.ub@renesas.com>.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210112165912.30876-5-uli+renesas@fpond.eu
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds config macros describing the voltage levels available on
a pin. The current default (3.3V/1.8V) maps to zero to avoid having to
change existing PFC implementations.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210112165912.30876-3-uli+renesas@fpond.eu
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Geert Uytterhoeven