memblock_x86_fill() could double memory array.
If we set memblock.current_limit to 512M, so memory array could be around 512M.
So kdump will not get big range (like 512M) under 1024M.
Try to put it down under 1M, it would use about 4k or so, and that is limited.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1353123563-3103-10-git-send-email-yinghai@kernel.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Now init_memory_mapping is called two times, later will be called for every
ram ranges.
Could put all related init_mem calling together and out of setup.c.
Actually, it reverts commit 1bbbbe7
x86: Exclude E820_RESERVED regions and memory holes above 4 GB from direct mapping.
will address that later with complete solution include handling hole under 4g.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1353123563-3103-5-git-send-email-yinghai@kernel.org
Reviewed-by: Pekka Enberg <penberg@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Now we pass around use_gbpages and use_pse for calculating page table size,
Later we will need to call init_memory_mapping for every ram range one by one,
that mean those calculation will be done several times.
Those information are the same for all ram range and could be stored in
page_size_mask and could be probed it one time only.
Move that probing code out of init_memory_mapping into separated function
probe_page_size_mask(), and call it before all init_memory_mapping.
Suggested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1353123563-3103-2-git-send-email-yinghai@kernel.org
Reviewed-by: Pekka Enberg <penberg@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
When I made an attempt at separating __pa_symbol and __pa I found that there
were a number of cases where __pa was used on an obvious symbol.
I also caught one non-obvious case as _brk_start and _brk_end are based on the
address of __brk_base which is a C visible symbol.
In mark_rodata_ro I was able to reduce the overhead of kernel symbol to
virtual memory translation by using a combination of __va(__pa_symbol())
instead of page_address(virt_to_page()).
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Link: http://lkml.kernel.org/r/20121116215640.8521.80483.stgit@ahduyck-cp1.jf.intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
When 32-bit EFI is used with 64-bit kernel (or vice versa), turn off
efi_enabled once setup is done. Beyond setup, it is normally used to
determine if runtime services are available and we will have none.
This will resolve issues stemming from efivars modprobe panicking on a
32/64-bit setup, as well as some reboot issues on similar setups.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=45991
Reported-by: Marko Kohtala <marko.kohtala@gmail.com>
Reported-by: Maxim Kammerer <mk@dee.su>
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Cc: stable@kernel.org # 3.4 - 3.6
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
We need to handle E820_RAM and E820_RESERVED_KERNEL at the same time.
Also memblock has page aligned range for ram, so we could avoid mapping
partial pages.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/CAE9FiQVZirvaBMFYRfXMmWEcHbKSicQEHz4VAwUv0xFCk51ZNw@mail.gmail.com
Acked-by: Jacob Shin <jacob.shin@amd.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@vger.kernel.org>
From Borislav Petkov <bp@amd64.org>:
Below is a RAS fix which reverts the addition of a sysfs attribute
which we agreed is not needed, post-factum. And this should go in now
because that sysfs attribute is going to end up in 3.7 otherwise and
thus exposed to userspace; removing it then would be a lot harder.
This is done as a merge rather than a simple patch/cherry-pick since
the baseline for this patch was not in the previous x86/urgent.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
On systems with very large memory (1 TB in our case), BIOS may report a
reserved region or a hole in the E820 map, even above the 4 GB range. Exclude
these from the direct mapping.
[ hpa: this should be done not just for > 4 GB but for everything above the legacy
region (1 MB), at the very least. That, however, turns out to require significant
restructuring. That work is well underway, but is not suitable for rc/stable. ]
Cc: stable@kernel.org # > 2.6.32
Signed-off-by: Jacob Shin <jacob.shin@amd.com>
Link: http://lkml.kernel.org/r/1319145326-13902-1-git-send-email-jacob.shin@amd.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Pull timer core update from Thomas Gleixner:
- Bug fixes (one for a longstanding dead loop issue)
- Rework of time related vsyscalls
- Alarm timer updates
- Jiffies updates to remove compile time dependencies
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timekeeping: Cast raw_interval to u64 to avoid shift overflow
timers: Fix endless looping between cascade() and internal_add_timer()
time/jiffies: bring back unconditional LATCH definition
time: Convert x86_64 to using new update_vsyscall
time: Only do nanosecond rounding on GENERIC_TIME_VSYSCALL_OLD systems
time: Introduce new GENERIC_TIME_VSYSCALL
time: Convert CONFIG_GENERIC_TIME_VSYSCALL to CONFIG_GENERIC_TIME_VSYSCALL_OLD
time: Move update_vsyscall definitions to timekeeper_internal.h
time: Move timekeeper structure to timekeeper_internal.h for vsyscall changes
jiffies: Remove compile time assumptions about CLOCK_TICK_RATE
jiffies: Kill unused TICK_USEC_TO_NSEC
alarmtimer: Rename alarmtimer_remove to alarmtimer_dequeue
alarmtimer: Remove unused helpers & defines
alarmtimer: Use hrtimer per-alarm instead of per-base
alarmtimer: Implement minimum alarm interval for allowing suspend
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=kN6V
-----END PGP SIGNATURE-----
Merge tag 'kvm-3.7-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Avi Kivity:
"Highlights of the changes for this release include support for vfio
level triggered interrupts, improved big real mode support on older
Intels, a streamlines guest page table walker, guest APIC speedups,
PIO optimizations, better overcommit handling, and read-only memory."
* tag 'kvm-3.7-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (138 commits)
KVM: s390: Fix vcpu_load handling in interrupt code
KVM: x86: Fix guest debug across vcpu INIT reset
KVM: Add resampling irqfds for level triggered interrupts
KVM: optimize apic interrupt delivery
KVM: MMU: Eliminate pointless temporary 'ac'
KVM: MMU: Avoid access/dirty update loop if all is well
KVM: MMU: Eliminate eperm temporary
KVM: MMU: Optimize is_last_gpte()
KVM: MMU: Simplify walk_addr_generic() loop
KVM: MMU: Optimize pte permission checks
KVM: MMU: Update accessed and dirty bits after guest pagetable walk
KVM: MMU: Move gpte_access() out of paging_tmpl.h
KVM: MMU: Optimize gpte_access() slightly
KVM: MMU: Push clean gpte write protection out of gpte_access()
KVM: clarify kvmclock documentation
KVM: make processes waiting on vcpu mutex killable
KVM: SVM: Make use of asm.h
KVM: VMX: Make use of asm.h
KVM: VMX: Make lto-friendly
KVM: x86: lapic: Clean up find_highest_vector() and count_vectors()
...
Conflicts:
arch/s390/include/asm/processor.h
arch/x86/kvm/i8259.c
"ACPI: Store valid ACPI tables passed via early initrd in reserved
memblock areas" breaks the build if either CONFIG_ACPI or
CONFIG_BLK_DEV_INITRD is disabled:
arch/x86/kernel/setup.c: In function 'setup_arch':
arch/x86/kernel/setup.c:944: error: implicit declaration of function 'acpi_initrd_override'
or
arch/x86/built-in.o: In function `setup_arch':
(.init.text+0x1397): undefined reference to `initrd_start'
arch/x86/built-in.o: In function `setup_arch':
(.init.text+0x139e): undefined reference to `initrd_end'
The dummy acpi_initrd_override() function in acpi.h isn't defined without
CONFIG_ACPI and initrd_{start,end} are declared but not defined without
CONFIG_BLK_DEV_INITRD.
[ hpa: applying this as a fix, but this really should be done cleaner ]
Signed-off-by: David Rientjes <rientjes@google.com>
Link: http://lkml.kernel.org/r/alpine.DEB.2.00.1210012032470.31644@chino.kir.corp.google.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Thomas Renninger <trenn@suse.de>
Cc: Len Brown <lenb@kernel.org>
A later patch will compare them with ACPI tables that get loaded at boot or
runtime and if criteria match, a stored one is loaded.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Link: http://lkml.kernel.org/r/1349043837-22659-4-git-send-email-trenn@suse.de
Cc: Len Brown <lenb@kernel.org>
Cc: Robert Moore <robert.moore@intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
CLOCK_TICK_RATE is used to accurately caclulate exactly how
a tick will be at a given HZ.
This is useful, because while we'd expect NSEC_PER_SEC/HZ,
the underlying hardware will have some granularity limit,
so we won't be able to have exactly HZ ticks per second.
This slight error can cause timekeeping quality problems
when using the jiffies or other jiffies driven clocksources.
Thus we currently use compile time CLOCK_TICK_RATE value to
generate SHIFTED_HZ and NSEC_PER_JIFFIES, which we then use
to adjust the jiffies clocksource to correct this error.
Unfortunately though, since CLOCK_TICK_RATE is a compile
time value, and the jiffies clocksource is registered very
early during boot, there are a number of cases where there
are different possible hardware timers that have different
tick rates. This causes problems in cases like ARM where
there are numerous different types of hardware, each having
their own compile-time CLOCK_TICK_RATE, making it hard to
accurately support different hardware with a single kernel.
For the most part, this doesn't matter all that much, as not
too many systems actually utilize the jiffies or jiffies driven
clocksource. Usually there are other highres clocksources
who's granularity error is negligable.
Even so, we have some complicated calcualtions that we do
everywhere to handle these edge cases.
This patch removes the compile time SHIFTED_HZ value, and
introduces a register_refined_jiffies() function. This results
in the default jiffies clock as being assumed a perfect HZ
freq, and allows archtectures that care about jiffies accuracy
to call register_refined_jiffies() with the tick rate, specified
dynamically at boot.
This allows us, where necessary, to not have a compile time
CLOCK_TICK_RATE constant, simplifies the jiffies code, and
still provides a way to have an accurate jiffies clock.
NOTE: Since this patch does not add register_refinied_jiffies()
calls for every arch, it may cause time quality regressions
in some cases. Its likely these will not be noticable, but
if they are an issue, adding the following to the end of
setup_arch() should resolve the regression:
register_refinied_jiffies(CLOCK_TICK_RATE)
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
At this stage x86_init.paging.pagetable_setup_done is only used in the
XEN case. Move its content in the x86_init.paging.pagetable_init setup
function and remove the now unused x86_init.paging.pagetable_setup_done
remaining infrastructure.
Signed-off-by: Attilio Rao <attilio.rao@citrix.com>
Acked-by: <konrad.wilk@oracle.com>
Cc: <Ian.Campbell@citrix.com>
Cc: <Stefano.Stabellini@eu.citrix.com>
Cc: <xen-devel@lists.xensource.com>
Link: http://lkml.kernel.org/r/1345580561-8506-5-git-send-email-attilio.rao@citrix.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Move the paging_init() call to the platform specific pagetable_init()
function, so we can get rid of the extra pagetable_setup_done()
function pointer.
Signed-off-by: Attilio Rao <attilio.rao@citrix.com>
Acked-by: <konrad.wilk@oracle.com>
Cc: <Ian.Campbell@citrix.com>
Cc: <Stefano.Stabellini@eu.citrix.com>
Cc: <xen-devel@lists.xensource.com>
Link: http://lkml.kernel.org/r/1345580561-8506-4-git-send-email-attilio.rao@citrix.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In preparation for unifying the pagetable_setup_start() and
pagetable_setup_done() setup functions, rename appropriately all the
infrastructure related to pagetable_setup_start().
Signed-off-by: Attilio Rao <attilio.rao@citrix.com>
Ackedd-by: <konrad.wilk@oracle.com>
Cc: <Ian.Campbell@citrix.com>
Cc: <Stefano.Stabellini@eu.citrix.com>
Cc: <xen-devel@lists.xensource.com>
Link: http://lkml.kernel.org/r/1345580561-8506-3-git-send-email-attilio.rao@citrix.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We either use swapper_pg_dir or the argument is unused. Preparatory
patch to simplify platform pagetable setup further.
Signed-off-by: Attilio Rao <attilio.rao@citrix.com>
Ackedb-by: <konrad.wilk@oracle.com>
Cc: <Ian.Campbell@citrix.com>
Cc: <Stefano.Stabellini@eu.citrix.com>
Cc: <xen-devel@lists.xensource.com>
Link: http://lkml.kernel.org/r/1345580561-8506-2-git-send-email-attilio.rao@citrix.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The distinction between CONFIG_KVM_CLOCK and CONFIG_KVM_GUEST is
not so clear anymore, as demonstrated by recent bugs caused by poor
handling of on/off combinations of these options.
Merge CONFIG_KVM_CLOCK into CONFIG_KVM_GUEST.
Reported-By: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Pull x86 trampoline rework from H. Peter Anvin:
"This code reworks all the "trampoline"/"realmode" code (various bits
that need to live in the first megabyte of memory, most but not all of
which runs in real mode at some point) in the kernel into a single
object. The main reason for doing this is that it eliminates the last
place in the kernel where we needed pages to be mapped RWX. This code
separates all that code into proper R/RW/RX pages."
Fix up conflicts in arch/x86/kernel/Makefile (mca removed next to reboot
code), and arch/x86/kernel/reboot.c (reboot code moved around in one
branch, modified in this one), and arch/x86/tools/relocs.c (mostly same
code came in earlier due to working around the ld bugs just before the
3.4 release).
Also remove stale x86-relocs entry from scripts/.gitignore as per Peter
Anvin.
* commit '61f5446169046c217a5479517edac3a890c3bee7': (36 commits)
x86, realmode: Move end signature into header.S
x86, relocs: When printing an error, say relative or absolute
x86, relocs: More relocations which may end up as absolute
x86, relocs: Workaround for binutils 2.22.52.0.1 section bug
xen-acpi-processor: Add missing #include <xen/xen.h>
acpi, bgrd: Add missing <linux/io.h> to drivers/acpi/bgrt.c
x86, realmode: Change EFER to a single u64 field
x86, realmode: Move kernel/realmode.c to realmode/init.c
x86, realmode: Move not-common bits out of trampoline_common.S
x86, realmode: Mask out EFER.LMA when saving trampoline EFER
x86, realmode: Fix no cache bits test in reboot_32.S
x86, realmode: Make sure all generated files are listed in targets
x86, realmode: build fix: remove duplicate build
x86, realmode: read cr4 and EFER from kernel for 64-bit trampoline
x86, realmode: fixes compilation issue in tboot.c
x86, realmode: move relocs from scripts/ to arch/x86/tools
x86, realmode: header for trampoline code
x86, realmode: flattened rm hierachy
x86, realmode: don't copy real_mode_header
x86, realmode: fix 64-bit wakeup sequence
...
Pull CMA and ARM DMA-mapping updates from Marek Szyprowski:
"These patches contain two major updates for DMA mapping subsystem
(mainly for ARM architecture). First one is Contiguous Memory
Allocator (CMA) which makes it possible for device drivers to allocate
big contiguous chunks of memory after the system has booted.
The main difference from the similar frameworks is the fact that CMA
allows to transparently reuse the memory region reserved for the big
chunk allocation as a system memory, so no memory is wasted when no
big chunk is allocated. Once the alloc request is issued, the
framework migrates system pages to create space for the required big
chunk of physically contiguous memory.
For more information one can refer to nice LWN articles:
- 'A reworked contiguous memory allocator':
http://lwn.net/Articles/447405/
- 'CMA and ARM':
http://lwn.net/Articles/450286/
- 'A deep dive into CMA':
http://lwn.net/Articles/486301/
- and the following thread with the patches and links to all previous
versions:
https://lkml.org/lkml/2012/4/3/204
The main client for this new framework is ARM DMA-mapping subsystem.
The second part provides a complete redesign in ARM DMA-mapping
subsystem. The core implementation has been changed to use common
struct dma_map_ops based infrastructure with the recent updates for
new dma attributes merged in v3.4-rc2. This allows to use more than
one implementation of dma-mapping calls and change/select them on the
struct device basis. The first client of this new infractructure is
dmabounce implementation which has been completely cut out of the
core, common code.
The last patch of this redesign update introduces a new, experimental
implementation of dma-mapping calls on top of generic IOMMU framework.
This lets ARM sub-platform to transparently use IOMMU for DMA-mapping
calls if one provides required IOMMU hardware.
For more information please refer to the following thread:
http://www.spinics.net/lists/arm-kernel/msg175729.html
The last patch merges changes from both updates and provides a
resolution for the conflicts which cannot be avoided when patches have
been applied on the same files (mainly arch/arm/mm/dma-mapping.c)."
Acked by Andrew Morton <akpm@linux-foundation.org>:
"Yup, this one please. It's had much work, plenty of review and I
think even Russell is happy with it."
* 'for-linus' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping: (28 commits)
ARM: dma-mapping: use PMD size for section unmap
cma: fix migration mode
ARM: integrate CMA with DMA-mapping subsystem
X86: integrate CMA with DMA-mapping subsystem
drivers: add Contiguous Memory Allocator
mm: trigger page reclaim in alloc_contig_range() to stabilise watermarks
mm: extract reclaim code from __alloc_pages_direct_reclaim()
mm: Serialize access to min_free_kbytes
mm: page_isolation: MIGRATE_CMA isolation functions added
mm: mmzone: MIGRATE_CMA migration type added
mm: page_alloc: change fallbacks array handling
mm: page_alloc: introduce alloc_contig_range()
mm: compaction: export some of the functions
mm: compaction: introduce isolate_freepages_range()
mm: compaction: introduce map_pages()
mm: compaction: introduce isolate_migratepages_range()
mm: page_alloc: remove trailing whitespace
ARM: dma-mapping: add support for IOMMU mapper
ARM: dma-mapping: use alloc, mmap, free from dma_ops
ARM: dma-mapping: remove redundant code and do the cleanup
...
Conflicts:
arch/x86/include/asm/dma-mapping.h
This reverts commit cf8ff6b6ab.
Just found this commit is a function duplicatation of commit 6b617e22
"x86/platform: Add a wallclock_init func to x86_init.timers ops".
Let's revert it and sorry for the noise.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Dirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull the MCA deletion branch from Paul Gortmaker:
"It was good that we could support MCA machines back in the day, but
realistically, nobody is using them anymore. They were mostly limited
to 386-sx 16MHz CPU and some 486 class machines and never more than
64MB of RAM. Even the enthusiast hobbyist community seems to have
dried up close to ten years ago, based on what you can find searching
various websites dedicated to the relatively short lived hardware.
So lets remove the support relating to CONFIG_MCA. There is no point
carrying this forward, wasting cycles doing routine maintenance on it;
wasting allyesconfig build time on validating it, wasting I/O on git
grep'ping over it, and so on."
Let's see if anybody screams. It generally has compiled, and James
Bottomley pointed out that there was a MCA extension from NCR that
allowed for up to 4GB of memory and PPro-class machines. So in *theory*
there may be users out there.
But even James (technically listed as a maintainer) doesn't actually
have a system, and while Alan Cox claims to have a machine in his cellar
that he offered to anybody who wants to take it off his hands, he didn't
argue for keeping MCA support either.
So we could bring it back. But somebody had better speak up and talk
about how they have actually been using said MCA hardware with modern
kernels for us to do that. And David already took the patch to delete
all the networking driver code (commit a5e371f61ad3: "drivers/net:
delete all code/drivers depending on CONFIG_MCA").
* 'delete-mca' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
MCA: delete all remaining traces of microchannel bus support.
scsi: delete the MCA specific drivers and driver code
serial: delete the MCA specific 8250 support.
arm: remove ability to select CONFIG_MCA
This patch adds support for CMA to dma-mapping subsystem for x86
architecture that uses common pci-dma/pci-nommu implementation. This
allows to test CMA on KVM/QEMU and a lot of common x86 boxes.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Hardware with MCA bus is limited to 386 and 486 class machines
that are now 20+ years old and typically with less than 32MB
of memory. A quick search on the internet, and you see that
even the MCA hobbyist/enthusiast community has lost interest
in the early 2000 era and never really even moved ahead from
the 2.4 kernels to the 2.6 series.
This deletes anything remaining related to CONFIG_MCA from core
kernel code and from the x86 architecture. There is no point in
carrying this any further into the future.
One complication to watch for is inadvertently scooping up
stuff relating to machine check, since there is overlap in
the TLA name space (e.g. arch/x86/boot/mca.c).
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: x86@kernel.org
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
If we've determined we can't do what the user asked, trying to do
something else isn't going to make the user's life better.
Without this the screen scrolls a bit and then you get a panic
anyway, and it's nice not to have so much scroll after the real
problem in bug reports.
Link: http://lkml.kernel.org/r/1337190206-12121-1-git-send-email-pjones@redhat.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Migrated ACPI wakeup code to the real-mode blob.
Code existing in .x86_trampoline can be completely
removed. Static descriptor table in wakeup_asm.S is
courtesy of H. Peter Anvin.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@intel.com>
Link: http://lkml.kernel.org/r/1336501366-28617-7-git-send-email-jarkko.sakkinen@intel.com
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <len.brown@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Implements relocator for real mode code that is called
as part of setup_arch(). Processes segment relocations
and linear relocations. Real-mode code is relocated to
a free hole below 1 MB.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@intel.com>
Link: http://lkml.kernel.org/r/1336501366-28617-4-git-send-email-jarkko.sakkinen@intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Commit 31b3c9d723 ("xen/x86: Implement x86_apic_ops") implemented
this:
... without considering that on UP the function pointer might be NULL.
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Link: http://lkml.kernel.org/n/tip-3pfty0ml4yp62phbkchichh0@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Which makes the code fit within the rest of the x86_ops functions.
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
[v1: Changed x86_apic -> x86_ioapic per Yinghai Lu <yinghai@kernel.org> suggestion]
[v2: Rebased on tip/x86/urgent and redid to match Ingo's syntax style]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Merge third batch of patches from Andrew Morton:
- Some MM stragglers
- core SMP library cleanups (on_each_cpu_mask)
- Some IPI optimisations
- kexec
- kdump
- IPMI
- the radix-tree iterator work
- various other misc bits.
"That'll do for -rc1. I still have ~10 patches for 3.4, will send
those along when they've baked a little more."
* emailed from Andrew Morton <akpm@linux-foundation.org>: (35 commits)
backlight: fix typo in tosa_lcd.c
crc32: add help text for the algorithm select option
mm: move hugepage test examples to tools/testing/selftests/vm
mm: move slabinfo.c to tools/vm
mm: move page-types.c from Documentation to tools/vm
selftests/Makefile: make `run_tests' depend on `all'
selftests: launch individual selftests from the main Makefile
radix-tree: use iterators in find_get_pages* functions
radix-tree: rewrite gang lookup using iterator
radix-tree: introduce bit-optimized iterator
fs/proc/namespaces.c: prevent crash when ns_entries[] is empty
nbd: rename the nbd_device variable from lo to nbd
pidns: add reboot_pid_ns() to handle the reboot syscall
sysctl: use bitmap library functions
ipmi: use locks on watchdog timeout set on reboot
ipmi: simplify locking
ipmi: fix message handling during panics
ipmi: use a tasklet for handling received messages
ipmi: increase KCS timeouts
ipmi: decrease the IPMI message transaction time in interrupt mode
...
crashkernel reservation need know the total memory size. Current
get_total_mem simply use max_pfn - min_low_pfn. It is wrong because it
will including memory holes in the middle.
Especially for kvm guest with memory > 0xe0000000, there's below in qemu
code: qemu split memory as below:
if (ram_size >= 0xe0000000 ) {
above_4g_mem_size = ram_size - 0xe0000000;
below_4g_mem_size = 0xe0000000;
} else {
below_4g_mem_size = ram_size;
}
So for 4G mem guest, seabios will insert a 512M usable region beyond of
4G. Thus in above case max_pfn - min_low_pfn will be more than original
memsize.
Fixing this issue by using memblock_phys_mem_size() to get the total
memsize.
Signed-off-by: Dave Young <dyoung@redhat.com>
Reviewed-by: WANG Cong <xiyou.wangcong@gmail.com>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Traditionally the kernel has refused to setup EFI at all if there's been
a mismatch in 32/64-bit mode between EFI and the kernel.
On some platforms that boot natively through EFI (Chrome OS being one),
we still need to get at least some of the static data such as memory
configuration out of EFI. Runtime services aren't as critical, and
it's a significant amount of work to implement switching between the
operating modes to call between kernel and firmware for thise cases. So
I'm ignoring it for now.
v5:
* Fixed some printk strings based on feedback
* Renamed 32/64-bit specific types to not have _ prefix
* Fixed bug in printout of efi runtime disablement
v4:
* Some of the earlier cleanup was accidentally reverted by this patch, fixed.
* Reworded some messages to not have to line wrap printk strings
v3:
* Reorganized to a series of patches to make it easier to review, and
do some of the cleanups I had left out before.
v2:
* Added graceful error handling for 32-bit kernel that gets passed
EFI data above 4GB.
* Removed some warnings that were missed in first version.
Signed-off-by: Olof Johansson <olof@lixom.net>
Link: http://lkml.kernel.org/r/1329081869-20779-6-git-send-email-olof@lixom.net
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Introduce a symbol, EFI_LOADER_SIGNATURE instead of using the magic
strings, which also helps to reduce the amount of ifdeffery.
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/1318848017-12301-1-git-send-email-matt@console-pimps.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
If we encounter an efi_memory_desc_t without EFI_MEMORY_WB set
in ->attribute we currently call set_memory_uc(), which in turn
calls __pa() on a potentially ioremap'd address.
On CONFIG_X86_32 this is invalid, resulting in the following
oops on some machines:
BUG: unable to handle kernel paging request at f7f22280
IP: [<c10257b9>] reserve_ram_pages_type+0x89/0x210
[...]
Call Trace:
[<c104f8ca>] ? page_is_ram+0x1a/0x40
[<c1025aff>] reserve_memtype+0xdf/0x2f0
[<c1024dc9>] set_memory_uc+0x49/0xa0
[<c19334d0>] efi_enter_virtual_mode+0x1c2/0x3aa
[<c19216d4>] start_kernel+0x291/0x2f2
[<c19211c7>] ? loglevel+0x1b/0x1b
[<c19210bf>] i386_start_kernel+0xbf/0xc8
A better approach to this problem is to map the memory region
with the correct attributes from the start, instead of modifying
it after the fact. The uncached case can be handled by
ioremap_nocache() and the cached by ioremap_cache().
Despite first impressions, it's not possible to use
ioremap_cache() to map all cached memory regions on
CONFIG_X86_64 because EFI_RUNTIME_SERVICES_DATA regions really
don't like being mapped into the vmalloc space, as detailed in
the following bug report,
https://bugzilla.redhat.com/show_bug.cgi?id=748516
Therefore, we need to ensure that any EFI_RUNTIME_SERVICES_DATA
regions are covered by the direct kernel mapping table on
CONFIG_X86_64. To accomplish this we now map E820_RESERVED_EFI
regions via the direct kernel mapping with the initial call to
init_memory_mapping() in setup_arch(), whereas previously these
regions wouldn't be mapped if they were after the last E820_RAM
region until efi_ioremap() was called. Doing it this way allows
us to delete efi_ioremap() completely.
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Huang Ying <huang.ying.caritas@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/1321621751-3650-1-git-send-email-matt@console-pimps.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Conflicts & resolutions:
* arch/x86/xen/setup.c
dc91c728fd "xen: allow extra memory to be in multiple regions"
24aa07882b "memblock, x86: Replace memblock_x86_reserve/free..."
conflicted on xen_add_extra_mem() updates. The resolution is
trivial as the latter just want to replace
memblock_x86_reserve_range() with memblock_reserve().
* drivers/pci/intel-iommu.c
166e9278a3 "x86/ia64: intel-iommu: move to drivers/iommu/"
5dfe8660a3 "bootmem: Replace work_with_active_regions() with..."
conflicted as the former moved the file under drivers/iommu/.
Resolved by applying the chnages from the latter on the moved
file.
* mm/Kconfig
6661672053 "memblock: add NO_BOOTMEM config symbol"
c378ddd53f "memblock, x86: Make ARCH_DISCARD_MEMBLOCK a config option"
conflicted trivially. Both added config options. Just
letting both add their own options resolves the conflict.
* mm/memblock.c
d1f0ece6cd "mm/memblock.c: small function definition fixes"
ed7b56a799 "memblock: Remove memblock_memory_can_coalesce()"
confliected. The former updates function removed by the
latter. Resolution is trivial.
Signed-off-by: Tejun Heo <tj@kernel.org>
Some wall clock devices use MMIO based HW register, this new
function will give them a chance to do some initialization work
before their get/set_time service get called.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Other than sanity check and debug message, the x86 specific version of
memblock reserve/free functions are simple wrappers around the generic
versions - memblock_reserve/free().
This patch adds debug messages with caller identification to the
generic versions and replaces x86 specific ones and kills them.
arch/x86/include/asm/memblock.h and arch/x86/mm/memblock.c are empty
after this change and removed.
Signed-off-by: Tejun Heo <tj@kernel.org>
Link: http://lkml.kernel.org/r/1310462166-31469-14-git-send-email-tj@kernel.org
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
25818f0f28 (memblock: Make MEMBLOCK_ERROR be 0) thankfully made
MEMBLOCK_ERROR 0 and there already are codes which expect error return
to be 0. There's no point in keeping MEMBLOCK_ERROR around. End its
misery.
Signed-off-by: Tejun Heo <tj@kernel.org>
Link: http://lkml.kernel.org/r/1310457490-3356-6-git-send-email-tj@kernel.org
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
UEFI stands for "Unified Extensible Firmware Interface", where "Firmware"
is an ancient African word meaning "Why do something right when you can
do it so wrong that children will weep and brave adults will cower before
you", and "UEI" is Celtic for "We missed DOS so we burned it into your
ROMs". The UEFI specification provides for runtime services (ie, another
way for the operating system to be forced to depend on the firmware) and
we rely on these for certain trivial tasks such as setting up the
bootloader. But some hardware fails to work if we attempt to use these
runtime services from physical mode, and so we have to switch into virtual
mode. So far so dreadful.
The specification makes it clear that the operating system is free to do
whatever it wants with boot services code after ExitBootServices() has been
called. SetVirtualAddressMap() can't be called until ExitBootServices() has
been. So, obviously, a whole bunch of EFI implementations call into boot
services code when we do that. Since we've been charmingly naive and
trusted that the specification may be somehow relevant to the real world,
we've already stuffed a picture of a penguin or something in that address
space. And just to make things more entertaining, we've also marked it
non-executable.
This patch allocates the boot services regions during EFI init and makes
sure that they're executable. Then, after SetVirtualAddressMap(), it
discards them and everyone lives happily ever after. Except for the ones
who have to work on EFI, who live sad lives haunted by the knowledge that
someone's eventually going to write yet another firmware specification.
[ hpa: adding this to urgent with a stable tag since it fixes currently-broken
hardware. However, I do not know what the dependencies are and so I do
not know which -stable versions this may be a candidate for. ]
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Link: http://lkml.kernel.org/r/1306331593-28715-1-git-send-email-mjg@redhat.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: <stable@kernel.org>
On larger systems, because of the numerous ACPI, Bootmem and EFI messages,
the static log buffer overflows before the larger one specified by the
log_buf_len param is allocated. Minimize the overflow by allocating the
new log buffer as soon as possible.
On kernels without memblock, a later call to setup_log_buf from
kernel/init.c is the fallback.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: fix CONFIG_PRINTK=n build]
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (27 commits)
PCI: Don't use dmi_name_in_vendors in quirk
PCI: remove unused AER functions
PCI/sysfs: move bus cpuaffinity to class dev_attrs
PCI: add rescan to /sys/.../pci_bus/.../
PCI: update bridge resources to get more big ranges when allocating space (again)
KVM: Use pci_store/load_saved_state() around VM device usage
PCI: Add interfaces to store and load the device saved state
PCI: Track the size of each saved capability data area
PCI/e1000e: Add and use pci_disable_link_state_locked()
x86/PCI: derive pcibios_last_bus from ACPI MCFG
PCI: add latency tolerance reporting enable/disable support
PCI: add OBFF enable/disable support
PCI: add ID-based ordering enable/disable support
PCI hotplug: acpiphp: assume device is in state D0 after powering on a slot.
PCI: Set PCIE maxpayload for card during hotplug insertion
PCI/ACPI: Report _OSC control mask returned on failure to get control
x86/PCI: irq and pci_ids patch for Intel Panther Point DeviceIDs
PCI: handle positive error codes
PCI: check pci_vpd_pci22_wait() return
PCI: Use ICH6_GPIO_EN in ich6_lpc_acpi_gpio
...
Fix up trivial conflicts in include/linux/pci_ids.h: commit a6e5e2be44
moved the intel SMBUS ID definitons to the i2c-i801.c driver.
* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, cpu: Fix detection of Celeron Covington stepping A1 and B0
Documentation, ABI: Update L3 cache index disable text
x86, AMD, cacheinfo: Fix L3 cache index disable checks
x86, AMD, cacheinfo: Fix fallout caused by max3 conversion
x86, cpu: Change NOP selection for certain Intel CPUs
x86, cpu: Clean up and unify the NOP selection infrastructure
x86, percpu: Use ASM_NOP4 instead of hardcoding P6_NOP4
x86, cpu: Move AMD Elan Kconfig under "Processor family"
Fix up trivial conflicts in alternative handling (commit dc326fca2b
"x86, cpu: Clean up and unify the NOP selection infrastructure" removed
some hacky 5-byte instruction stuff, while commit d430d3d7e6 "jump
label: Introduce static_branch() interface" renamed HAVE_JUMP_LABEL to
CONFIG_JUMP_LABEL in the code that went away)
This workaround holds a dma32 buffer at early boot to prevent later
bootmem allocations from stealing it in the case of large RAM configs.
Now that x86 is using memblock, and the nobootmem wrapper does top-down
allocation, it's no longer necessary, so remove it.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Clean up and unify the NOP selection infrastructure:
- Make the atomic 5-byte NOP a part of the selection system.
- Pick NOPs once during early boot and then be done with it.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jason Baron <jbaron@redhat.com>
Link: http://lkml.kernel.org/r/1303166160-10315-3-git-send-email-hpa@linux.intel.com
Restore the initialization of mmu_cr4_features during boot, which was
removed without comment in checkin e5f15b45dd
x86: Cleanup highmap after brk is concluded
thereby breaking resume from hibernate. This restores previous
functionality in approximately the same place, and corrects the
reading of %cr4 on pre-CPUID hardware (%cr4 exists if and only if
CPUID is supported.)
However, part of the problem is that the hibernate suspend/resume
sequence should manage the save/restore of %cr4 explicitly.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Cc: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <201104020154.57136.rjw@sisk.pl>
The Xen PV drivers in a crashed HVM guest can not connect to the dom0
backend drivers because both frontend and backend drivers are still in
connected state. To run the connection reset function only in case of a
crashdump, the is_kdump_kernel() function needs to be available for the PV
driver modules.
Consolidate elfcorehdr_addr, setup_elfcorehdr and saved_max_pfn into
kernel/crash_dump.c Also export elfcorehdr_addr to make is_kdump_kernel()
usable for modules.
Leave 'elfcorehdr' as early_param(). This changes powerpc from __setup()
to early_param(). It adds an address range check from x86 also on ia64
and powerpc.
[akpm@linux-foundation.org: additional #includes]
[akpm@linux-foundation.org: remove elfcorehdr_addr export]
[akpm@linux-foundation.org: fix for Tejun's mm/nobootmem.c changes]
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
xen: update mask_rw_pte after kernel page tables init changes
xen: set max_pfn_mapped to the last pfn mapped
x86: Cleanup highmap after brk is concluded
Fix up trivial onflict (added header file includes) in
arch/x86/mm/init_64.c
Now cleanup_highmap actually is in two steps: one is early in head64.c
and only clears above _end; a second one is in init_memory_mapping() and
tries to clean from _brk_end to _end.
It should check if those boundaries are PMD_SIZE aligned but currently
does not.
Also init_memory_mapping() is called several times for numa or memory
hotplug, so we really should not handle initial kernel mappings there.
This patch moves cleanup_highmap() down after _brk_end is settled so
we can do everything in one step.
Also we honor max_pfn_mapped in the implementation of cleanup_highmap.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
LKML-Reference: <alpine.DEB.2.00.1103171739050.3382@kaball-desktop>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'x86-trampoline-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Fix binutils-2.21 symbol related build failures
x86-64, trampoline: Remove unused variable
x86, reboot: Fix the use of passed arguments in 32-bit BIOS reboot
x86, reboot: Move the real-mode reboot code to an assembly file
x86: Make the GDT_ENTRY() macro in <asm/segment.h> safe for assembly
x86, trampoline: Use the unified trampoline setup for ACPI wakeup
x86, trampoline: Common infrastructure for low memory trampolines
Fix up trivial conflicts in arch/x86/kernel/Makefile
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (27 commits)
x86: Clean up apic.c and apic.h
x86: Remove superflous goal definition of tsc_sync
x86: dt: Correct local apic documentation in device tree bindings
x86: dt: Cleanup local apic setup
x86: dt: Fix OLPC=y/INTEL_CE=n build
rtc: cmos: Add OF bindings
x86: ce4100: Use OF to setup devices
x86: ioapic: Add OF bindings for IO_APIC
x86: dtb: Add generic bus probe
x86: dtb: Add support for PCI devices backed by dtb nodes
x86: dtb: Add device tree support for HPET
x86: dtb: Add early parsing of IO_APIC
x86: dtb: Add irq domain abstraction
x86: dtb: Add a device tree for CE4100
x86: Add device tree support
x86: e820: Remove conditional early mapping in parse_e820_ext
x86: OLPC: Make OLPC=n build again
x86: OLPC: Remove extra OLPC_OPENFIRMWARE_DT indirection
x86: OLPC: Cleanup config maze completely
x86: OLPC: Hide OLPC_OPENFIRMWARE config switch
...
Fix up conflicts in arch/x86/platform/ce4100/ce4100.c
This patch reverts NUMA affine page table allocation added by commit
1411e0ec31 (x86-64, numa: Put pgtable to local node memory).
The commit made an undocumented change where the kernel linear mapping
strictly follows intersection of e820 memory map and NUMA
configuration. If the physical memory configuration has holes or NUMA
nodes are not properly aligned, this leads to using unnecessarily
smaller mapping size which leads to increased TLB pressure. For
details,
http://thread.gmane.org/gmane.linux.kernel/1104672
Patches to fix the problem have been proposed but the underlying code
needs more cleanup and the approach itself seems a bit heavy handed
and it has been determined to revert the feature for now and come back
to it in the next developement cycle.
http://thread.gmane.org/gmane.linux.kernel/1105959
As init_memory_mapping_high() callsites have been consolidated since
the commit, reverting is done manually. Also, the RED-PEN comment in
arch/x86/mm/init.c is not restored as the problem no longer exists
with memblock based top-down early memory allocation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Up to now we force enable the local apic in the devicetree setup
uncoditionally and set smp_found_config unconditionally to 1 when a
devicetree blob is available. This breaks, when local apic is disabled
in the Kconfig.
Make it consistent by initializing device tree explicitely before
smp_get_config() so a non lapic configuration could be used as well.
To be functional that would require to implement PIT as an interrupt
host, but the only user of this code until now is ce4100 which
requires apics to be available. So we leave this up to those who need
it.
Tested-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch adds minimal support for device tree on x86. The device
tree blob is passed to the kernel via setup_data which requires at
least boot protocol 2.09.
Memory size, restricted memory regions, boot arguments are gathered
the traditional way so things like cmd_line are just here to let the
code compile.
The current plan is use the device tree as an extension and to gather
information which can not be enumerated and would have to be hardcoded
otherwise. This includes things like
- which devices are on this I2C/SPI bus?
- how are the interrupts wired to IO APIC?
- where could my hpet be?
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: sodaville@linutronix.de
Cc: devicetree-discuss@lists.ozlabs.org
LKML-Reference: <1298405266-1624-3-git-send-email-bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch ensures that the memory passed from parse_setup_data() is
large enough to cover the complete data structure. That means that the
conditional mapping in parse_e820_ext() can go.
While here, I also attempt not to map two pages if the address is not
aligned to a page boundary.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Cc: sodaville@linutronix.de
Cc: devicetree-discuss@lists.ozlabs.org
LKML-Reference: <1298405266-1624-2-git-send-email-bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use the unified trampoline allocation setup to allocate and install
the ACPI wakeup code in low memory.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
LKML-Reference: <4D5DFBE4.7090104@intel.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Matthieu Castet <castet.matthieu@free.fr>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Common infrastructure for low memory trampolines. This code installs
the trampolines permanently in low memory very early. It also permits
multiple pieces of code to be used for this purpose.
This code also introduces a standard infrastructure for computing
symbol addresses in the trampoline code.
The only change to the actual SMP trampolines themselves is that the
64-bit trampoline has been made reusable -- the previous version would
overwrite the code with a status variable; this moves the status
variable to a separate location.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
LKML-Reference: <4D5DFBE4.7090104@intel.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Matthieu Castet <castet.matthieu@free.fr>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
There's no reason for these to live in setup_arch(). Move them inside
initmem_init().
- v2: x86-32 initmem_init() weren't updated breaking 32bit builds.
Fixed. Found by Ankita.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ankita Garg <ankita@in.ibm.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Shaohui Zheng <shaohui.zheng@intel.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Because of the way ACPI tables are parsed, the generic
acpi_numa_init() couldn't return failure when error was detected by
arch hooks. Instead, the failure state was recorded and later arch
dependent init hook - acpi_scan_nodes() - would fail.
Wrap acpi_numa_init() with x86_acpi_numa_init() so that failure can be
indicated as return value immediately. This is in preparation for
further NUMA init cleanups.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Shaohui Zheng <shaohui.zheng@intel.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: H. Peter Anvin <hpa@linux.intel.com>
The functions used during NUMA initialization - *_numa_init() and
*_scan_nodes() - have different arguments and return values. Unify
them such that they all take no argument and return 0 on success and
-errno on failure. This is in preparation for further NUMA init
cleanups.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Shaohui Zheng <shaohui.zheng@intel.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: H. Peter Anvin <hpa@linux.intel.com>
initmem_init() extensively accesses and modifies global data
structures and the parameters aren't even followed depending on which
path is being used. Drop @start/last_pfn and let it deal with
@max_pfn directly. This is in preparation for further NUMA init
cleanups.
- v2: x86-32 initmem_init() weren't updated breaking 32bit builds.
Fixed. Found by Yinghai.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Shaohui Zheng <shaohui.zheng@intel.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Some wall clock devices use MMIO based HW register, this new
function will give them a chance to do some initialization work
before their get/set_time service get called, which is usually
in early kernel boot phase.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Conflicts:
arch/x86/mm/numa_64.c
Merge reason: fix the conflict, update to latest -rc and pick up this
dependent fix from Yinghai:
e6d2e2b2b1e1: memblock: don't adjust size in memblock_find_base()
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Now that everything else is unified, NUMA initialization can be
unified too.
* numa_init_array() and init_cpu_to_node() are moved from
numa_64 to numa.
* numa_32::initmem_init() is updated to call numa_init_array()
and setup_arch() to call init_cpu_to_node() on 32bit too.
* x86_cpu_to_node_map is now initialized to NUMA_NO_NODE on
32bit too. This is safe now as numa_init_array() will initialize
it early during boot.
This makes NUMA mapping fully initialized before
setup_per_cpu_areas() on 32bit too and thus makes the first
percpu chunk which contains all the static variables and some of
dynamic area allocated with NUMA affinity correctly considered.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: yinghai@kernel.org
Cc: brgerst@gmail.com
Cc: gorcunov@gmail.com
Cc: shaohui.zheng@intel.com
Cc: rientjes@google.com
LKML-Reference: <1295789862-25482-17-git-send-email-tj@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Reviewed-by: Pekka Enberg <penberg@kernel.org>
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Fix APIC ID sizing bug on larger systems, clean up MAX_APICS confusion
x86, acpi: Parse all SRAT cpu entries even above the cpu number limitation
x86, acpi: Add MAX_LOCAL_APIC for 32bit
x86: io_apic: Split setup_ioapic_ids_from_mpc()
x86: io_apic: Fix CONFIG_X86_IO_APIC=n breakage
x86: apic: Move probe_nr_irqs_gsi() into ioapic_init_mappings()
x86: Allow platforms to force enable apic
* 'x86-amd-nb-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, cacheinfo: Cleanup L3 cache index disable support
x86, amd-nb: Cleanup AMD northbridge caching code
x86, amd-nb: Complete the rename of AMD NB and related code
It is not related to init_memory_mapping(), and init_memory_mapping() is
getting more bigger.
So make it as seperated function and call it from reserve_brk() and that is
point when _brk_end is concluded.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4D1933E0.7090305@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Move it into head file. to prepare use it in other files.
[ hpa: added missing <linux/types.h> and changed type to phys_addr_t. ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4D1933BA.8000508@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf probe: Fix to support libdwfl older than 0.148
perf tools: Fix lazy wildcard matching
perf buildid-list: Fix error return for success
perf buildid-cache: Fix symbolic link handling
perf symbols: Stop using vmlinux files with no symbols
perf probe: Fix use of kernel image path given by 'k' option
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, kexec: Limit the crashkernel address appropriately
Keep the crash kernel address below 512 MiB for 32 bits and 896 MiB
for 64 bits. For 32 bits, this retains compatibility with earlier
kernel releases, and makes it work even if the vmalloc= setting is
adjusted.
For 64 bits, we should be able to increase this substantially once a
hard-coded limit in kexec-tools is fixed.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <20101217195035.GE14502@redhat.com>
Not only the naming of the files was confusing, it was even more so for
the function and variable names.
Renamed the K8 NB and NUMA stuff that is also used on other AMD
platforms. This also renames the CONFIG_K8_NUMA option to
CONFIG_AMD_NUMA and the related file k8topology_64.c to
amdtopology_64.c. No functional changes intended.
Signed-off-by: Hans Rosenfeld <hans.rosenfeld@amd.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (27 commits)
x86: allocate space within a region top-down
x86: update iomem_resource end based on CPU physical address capabilities
x86/PCI: allocate space from the end of a region, not the beginning
PCI: allocate bus resources from the top down
resources: support allocating space within a region from the top down
resources: handle overflow when aligning start of available area
resources: ensure callback doesn't allocate outside available space
resources: factor out resource_clip() to simplify find_resource()
resources: add a default alignf to simplify find_resource()
x86/PCI: MMCONFIG: fix region end calculation
PCI: Add support for polling PME state on suspended legacy PCI devices
PCI: Export some PCI PM functionality
PCI: fix message typo
PCI: log vendor/device ID always
PCI: update Intel chipset names and defines
PCI: use new ccflags variable in Makefile
PCI: add PCI_MSIX_TABLE/PBA defines
PCI: add PCI vendor id for STmicroelectronics
x86/PCI: irq and pci_ids patch for Intel Patsburg DeviceIDs
PCI: OLPC: Only enable PCI configuration type override on XO-1
...
Request that allocate_resource() use available space from high addresses
first, rather than the default of using low addresses first.
The most common place this makes a difference is when we move or assign
new PCI device resources. Low addresses are generally scarce, so it's
better to use high addresses when possible. This follows Windows practice
for PCI allocation.
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=16228#c42
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The iomem_resource map reflects the available physical address space.
We statically initialize the end to -1, i.e., 0xffffffff_ffffffff, but
of course we can only use as much as the CPU can address.
This patch updates the end based on the CPU capabilities, so we don't
mistakenly allocate space that isn't usable, as we're likely to do when
allocating from the top-down.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
probe_br_irqs_gsi() is called right after ioapic_init_mappings() and
there are no other users. Move it into ioapic_init_mappings() so the
declaration can disappear and the function can become static.
Rename ioapic_init_mappings() to ioapic_and_gsi_init() to reflect that
change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <1287510389-8388-2-git-send-email-dirk.brandewie@gmail.com>
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
* 'x86-trampoline-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86-32, mm: Add an initial page table for core bootstrapping
* 'core-memblock-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (74 commits)
x86-64: Only set max_pfn_mapped to 512 MiB if we enter via head_64.S
xen: Cope with unmapped pages when initializing kernel pagetable
memblock, bootmem: Round pfn properly for memory and reserved regions
memblock: Annotate memblock functions with __init_memblock
memblock: Allow memblock_init to be called early
memblock/arm: Fix memblock_region_is_memory() typo
x86, memblock: Remove __memblock_x86_find_in_range_size()
memblock: Fix wraparound in find_region()
x86-32, memblock: Make add_highpages honor early reserved ranges
x86, memblock: Fix crashkernel allocation
arm, memblock: Fix the sparsemem build
memblock: Fix section mismatch warnings
powerpc, memblock: Fix memblock API change fallout
memblock, microblaze: Fix memblock API change fallout
x86: Remove old bootmem code
x86, memblock: Use memblock_memory_size()/memblock_free_memory_size() to get correct dma_reserve
x86: Remove not used early_res code
x86, memblock: Replace e820_/_early string with memblock_
x86: Use memblock to replace early_res
x86, memblock: Use memblock_debug to control debug message print out
...
Fix up trivial conflicts in arch/x86/kernel/setup.c and kernel/Makefile
* 'x86-vmware-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, paravirt: Remove alloc_pmd_clone hook, only used by VMI
x86, vmware: Remove deprecated VMI kernel support
Fix up trivial #include conflict in arch/x86/kernel/smpboot.c
* 'x86-bios-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, bios: Make the x86 early memory reservation a kernel option
x86, bios: By default, reserve the low 64K for all BIOSes
* 'x86-amd-nb-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, amd_nb: Enable GART support for AMD family 0x15 CPUs
x86, amd: Use compute unit information to determine thread siblings
x86, amd: Extract compute unit information for AMD CPUs
x86, amd: Add support for CPUID topology extension of AMD CPUs
x86, nmi: Support NMI watchdog on newer AMD CPU families
x86, mtrr: Assume SYS_CFG[Tom2ForceMemTypeWB] exists on all future AMD CPUs
x86, k8: Rename k8.[ch] to amd_nb.[ch] and CONFIG_K8_NB to CONFIG_AMD_NB
x86, k8-gart: Decouple handling of garts and northbridges
x86, cacheinfo: Fix dependency of AMD L3 CID
x86, kvm: add new AMD SVM feature bits
x86, cpu: Fix allowed CPUID bits for KVM guests
x86, cpu: Update AMD CPUID feature bits
x86, cpu: Fix renamed, not-yet-shipping AMD CPUID feature bit
x86, AMD: Remove needless CPU family check (for L3 cache info)
x86, tsc: Remove CPU frequency calibration on AMD
This patch adds an initial page table with low mappings used exclusively
for booting APs/resuming after ACPI suspend/machine restart. After this,
there's no need to add low mappings to swapper_pg_dir and zap them later
or create own swsusp PGD page solely for ACPI sleep needs - we have
initial_page_table for that.
Signed-off-by: Borislav Petkov <bp@alien8.de>
LKML-Reference: <20101020070526.GA9588@liondog.tnic>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
head_64.S maps up to 512 MiB, but that is not necessarity true for
other entry paths, such as Xen.
Thus, co-locate the setting of max_pfn_mapped with the code to
actually set up the page tables in head_64.S. The 32-bit code is
already so co-located. (The Xen code already sets max_pfn_mapped
correctly for its own use case.)
-v2:
Yinghai fixed the following bug in this patch:
|
| max_pfn_mapped is in .bss section, so we need to set that
| after bss get cleared. Without that we crash on bootup.
|
| That is safe because Xen does not call x86_64_start_kernel().
|
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Fixed-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
LKML-Reference: <4CB6AB24.9020504@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cai Qian found crashkernel is broken with the x86 memblock changes.
1. crashkernel=128M@32M always reported that range is used, even if
the first kernel is small and does not usethat range
2. we always got following report when using "kexec -p"
Could not find a free area of memory of a000 bytes...
locate_hole failed
The root cause is that generic memblock_find_in_range() will try to
allocate from the top of the range, whereas the kexec code was written
assuming that allocation was always near the bottom and that it could
blindly extend memory upward. Unfortunately the kexec code doesn't
have a system for requesting the range that it really needs, so this
is subject to probabilistic failures.
This patch hacks around the problem by limiting the target range
heuristically to below the traditional bzImage max range. This number
is arbitrary and not always correct, and a much better result would be
obtained by having kexec communicate this number based on the kernel
header information and any appropriate command line options.
Reported-and-Bisected-by: CAI Qian <caiqian@redhat.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4CABAF2A.5090501@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Move Steve's code for finding the best 5-byte no-op from ftrace.c to
alternative.c. The idea is that other consumers (in this case jump label)
want to make use of that code.
Signed-off-by: Jason Baron <jbaron@redhat.com>
LKML-Reference: <96259ae74172dcac99c0020c249743c523a92e18.1284733808.git.jbaron@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The file names are somehow misleading as the code is not specific to
AMD K8 CPUs anymore. The files accomodate code for other AMD CPU
northbridges as well.
Same is true for the config option which is valid for AMD CPU
northbridges in general and not specific to K8.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
LKML-Reference: <20100917160343.GD4958@loge.amd.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Requested by Ingo, Thomas and HPA.
The old bootmem code is no longer necessary, and the transition is
complete. Remove it.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
memblock_memory_size() will return memory size in memblock.memory.region.
memblock_free_memory_size() will return free memory size in memblock.memory.region.
So We can get exact reseved size in specified range.
Set the size right after initmem_init(), because later bootmem API will
get area above 16M. (except some fallback).
Later after we remove the bootmem, We could call that just before paging_init().
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
1.include linux/memblock.h directly. so later could reduce e820.h reference.
2 this patch is done by sed scripts mainly
-v2: use MEMBLOCK_ERROR instead of -1ULL or -1UL
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
1. replace find_e820_area with memblock_find_in_range
2. replace reserve_early with memblock_x86_reserve_range
3. replace free_early with memblock_x86_free_range.
4. NO_BOOTMEM will switch to use memblock too.
5. use _e820, _early wrap in the patch, in following patch, will
replace them all
6. because memblock_x86_free_range support partial free, we can remove some special care
7. Need to make sure that memblock_find_in_range() is called after memblock_x86_fill()
so adjust some calling later in setup.c::setup_arch()
-- corruption_check and mptable_update
-v2: Move reserve_brk() early
Before fill_memblock_area, to avoid overlap between brk and memblock_find_in_range()
that could happen We have more then 128 RAM entry in E820 tables, and
memblock_x86_fill() could use memblock_find_in_range() to find a new place for
memblock.memory.region array.
and We don't need to use extend_brk() after fill_memblock_area()
So move reserve_brk() early before fill_memblock_area().
-v3: Move find_smp_config early
To make sure memblock_find_in_range not find wrong place, if BIOS doesn't put mptable
in right place.
-v4: Treat RESERVED_KERN as RAM in memblock.memory. and they are already in
memblock.reserved already..
use __NOT_KEEP_MEMBLOCK to make sure memblock related code could be freed later.
-v5: Generic version __memblock_find_in_range() is going from high to low, and for 32bit
active_region for 32bit does include high pages
need to replace the limit with memblock.default_alloc_limit, aka get_max_mapped()
-v6: Use current_limit instead
-v7: check with MEMBLOCK_ERROR instead of -1ULL or -1L
-v8: Set memblock_can_resize early to handle EFI with more RAM entries
-v9: update after kmemleak changes in mainline
Suggested-by: David S. Miller <davem@davemloft.net>
Suggested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Add a kernel command-line option so the x86 early memory reservation
size can be adjusted at runtime instead of only at compile time.
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <tip-d0cd7425fab774a480cce17c2f649984312d0b55@git.kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The laundry list of BIOSes that need the low 64K reserved is getting
very long, so make it the default across all BIOSes. This also allows
the code to be simplified and unified with the reservation code for
the first 4K.
This resolves kernel bugzilla 16661 and who knows what else...
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
LKML-Reference: <tip-*@git.kernel.org>
With the recent innovations in CPU hardware acceleration technologies
from Intel and AMD, VMware ran a few experiments to compare these
techniques to guest paravirtualization technique on VMware's platform.
These hardware assisted virtualization techniques have outperformed the
performance benefits provided by VMI in most of the workloads. VMware
expects that these hardware features will be ubiquitous in a couple of
years, as a result, VMware has started a phased retirement of this
feature from the hypervisor.
Please note that VMI has always been an optimization and non-VMI kernels
still work fine on VMware's platform.
Latest versions of VMware's product which support VMI are,
Workstation 7.0 and VSphere 4.0 on ESX side, future maintainence
releases for these products will continue supporting VMI.
For more details about VMI retirement take a look at this,
http://blogs.vmware.com/guestosguide/2009/09/vmi-retirement.html
This feature removal was scheduled for 2.6.37 back in September 2009.
Signed-off-by: Alok N Kataria <akataria@vmware.com>
LKML-Reference: <1282600151.19396.22.camel@ank32.eng.vmware.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
This patch fixes machine crashes which occur when heavily exercising the
CPU hotplug codepaths on a 32-bit kernel. These crashes are caused by
AMD Erratum 383 and result in a fatal machine check exception. Here's
the scenario:
1. On 32-bit, the swapper_pg_dir page table is used as the initial page
table for booting a secondary CPU.
2. To make this work, swapper_pg_dir needs a direct mapping of physical
memory in it (the low mappings). By adding those low, large page (2M)
mappings (PAE kernel), we create the necessary conditions for Erratum
383 to occur.
3. Other CPUs which do not participate in the off- and onlining game may
use swapper_pg_dir while the low mappings are present (when leave_mm is
called). For all steps below, the CPU referred to is a CPU that is using
swapper_pg_dir, and not the CPU which is being onlined.
4. The presence of the low mappings in swapper_pg_dir can result
in TLB entries for addresses below __PAGE_OFFSET to be established
speculatively. These TLB entries are marked global and large.
5. When the CPU with such TLB entry switches to another page table, this
TLB entry remains because it is global.
6. The process then generates an access to an address covered by the
above TLB entry but there is a permission mismatch - the TLB entry
covers a large global page not accessible to userspace.
7. Due to this permission mismatch a new 4kb, user TLB entry gets
established. Further, Erratum 383 provides for a small window of time
where both TLB entries are present. This results in an uncorrectable
machine check exception signalling a TLB multimatch which panics the
machine.
There are two ways to fix this issue:
1. Always do a global TLB flush when a new cr3 is loaded and the
old page table was swapper_pg_dir. I consider this a hack hard
to understand and with performance implications
2. Do not use swapper_pg_dir to boot secondary CPUs like 64-bit
does.
This patch implements solution 2. It introduces a trampoline_pg_dir
which has the same layout as swapper_pg_dir with low_mappings. This page
table is used as the initial page table of the booting CPU. Later in the
bringup process, it switches to swapper_pg_dir and does a global TLB
flush. This fixes the crashes in our test cases.
-v2: switch to swapper_pg_dir right after entering start_secondary() so
that we are able to access percpu data which might not be mapped in the
trampoline page table.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
LKML-Reference: <20100816123833.GB28147@aftab>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
boot_cpu_id is there for historical reasons and was renamed to
boot_cpu_physical_apicid in patch:
c70dcb7 x86: change boot_cpu_id to boot_cpu_physical_apicid
However, there are some remaining occurrences of boot_cpu_id that are
never touched in the kernel and thus its value is always 0.
This patch removes boot_cpu_id completely.
Signed-off-by: Robert Richter <robert.richter@amd.com>
LKML-Reference: <1279731838-1522-8-git-send-email-robert.richter@amd.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Add support for saving OFW's cif, and later calling into it to run OFW
commands. OFW remains resident in memory, living within virtual range
0xff800000 - 0xffc00000. A single page directory entry points to the
pgdir that OFW actually uses, so rather than saving the entire page
table, we grab and install that one entry permanently in the kernel's
page table.
This is currently only used by the OLPC XO. Note that this particular
calling convention breaks PAE and PAT, and so cannot be used on newer
x86 hardware.
Signed-off-by: Andres Salomon <dilinger@queued.net>
LKML-Reference: <20100618174653.7755a39a@dev.queued.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The low-memory corruption checker triggers during suspend/resume, so we
need to reserve the low 64k. Don't be fooled that the BIOS identifies
itself as "Dell Inc.", it's still Phoenix BIOS.
[ hpa: I think we blacklist almost every BIOS in existence. We should
either change this to a whitelist or just make it unconditional. ]
Signed-off-by: Gabor Gombas <gombasg@digikabel.hu>
LKML-Reference: <201005241913.o4OJDIMM010877@imap1.linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@kernel.org>
Allow the x86 arch to have early exception processing for the purpose
of debugging via the kgdb.
Signed-off-by: Jan Kiszka <jan.kiszka@web.de>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-tip:
x86: Fix double enable_IR_x2apic() call on SMP kernel on !SMP boards
x86: Increase CONFIG_NODES_SHIFT max to 10
ibft, x86: Change reserve_ibft_region() to find_ibft_region()
x86, hpet: Fix bug in RTC emulation
x86, hpet: Erratum workaround for read after write of HPET comparator
bootmem, x86: Fix 32bit numa system without RAM on node 0
nobootmem, x86: Fix 32bit numa system without RAM on node 0
x86: Handle overlapping mptables
x86: Make e820_remove_range to handle all covered case
x86-32, resume: do a global tlb flush in S4 resume
This allows arch code could decide the way to reserve the ibft.
And we should reserve ibft as early as possible, instead of BOOTMEM
stage, in case the table is in RAM range and is not reserved by BIOS
(this will often be the case.)
Move to just after find_smp_config().
Also when CONFIG_NO_BOOTMEM=y, We will not have reserve_bootmem() anymore.
-v2: fix typo about ibft pointed by Konrad Rzeszutek Wilk <konrad@darnok.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4BB510FB.80601@kernel.org>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Peter Jones <pjones@redhat.com>
Cc: Konrad Rzeszutek Wilk <konrad@kernel.org>
CC: Jan Beulich <jbeulich@novell.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
When CONFIG_NO_BOOTMEM=y, it could use memory more effiently, or
in a more compact fashion.
Example:
Allocated new RAMDISK: 00ec2000 - 0248ce57
Move RAMDISK from 000000002ea04000 - 000000002ffcee56 to 00ec2000 - 0248ce56
The new RAMDISK's end is not page aligned.
Last page could be shared with other users.
When free_init_pages are called for initrd or .init, the page
could be freed and we could corrupt other data.
code segment in free_init_pages():
| for (; addr < end; addr += PAGE_SIZE) {
| ClearPageReserved(virt_to_page(addr));
| init_page_count(virt_to_page(addr));
| memset((void *)(addr & ~(PAGE_SIZE-1)),
| POISON_FREE_INITMEM, PAGE_SIZE);
| free_page(addr);
| totalram_pages++;
| }
last half page could be used as one whole free page.
So page align the boundaries.
-v2: make the original initramdisk to be aligned, according to
Johannes, otherwise we have the chance to lose one page.
we still need to keep initrd_end not aligned, otherwise it could
confuse decompressor.
-v3: change to WARN_ON instead, suggested by Johannes.
-v4: use PAGE_ALIGN, suggested by Johannes.
We may fix that macro name later to PAGE_ALIGN_UP, and PAGE_ALIGN_DOWN
Add comments about assuming ramdisk start is aligned
in relocate_initrd(), change to re get ramdisk_image instead of save it
to make diff smaller. Add warning for wrong range, suggested by Johannes.
-v6: remove one WARN()
We need to align beginning in free_init_pages()
do not copy more than ramdisk_size, noticed by Johannes
Reported-by: Stanislaw Gruszka <sgruszka@redhat.com>
Tested-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: David Miller <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <1269830604-26214-3-git-send-email-yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-bootmem-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (30 commits)
early_res: Need to save the allocation name in drop_range_partial()
sparsemem: Fix compilation on PowerPC
early_res: Add free_early_partial()
x86: Fix non-bootmem compilation on PowerPC
core: Move early_res from arch/x86 to kernel/
x86: Add find_fw_memmap_area
Move round_up/down to kernel.h
x86: Make 32bit support NO_BOOTMEM
early_res: Enhance check_and_double_early_res
x86: Move back find_e820_area to e820.c
x86: Add find_early_area_size
x86: Separate early_res related code from e820.c
x86: Move bios page reserve early to head32/64.c
sparsemem: Put mem map for one node together.
sparsemem: Put usemap for one node together
x86: Make 64 bit use early_res instead of bootmem before slab
x86: Only call dma32_reserve_bootmem 64bit !CONFIG_NUMA
x86: Make early_node_mem get mem > 4 GB if possible
x86: Dynamically increase early_res array size
x86: Introduce max_early_res and early_res_count
...
This will save 64K bytes from memory when loading linux if DMI is
disabled, which is good for embedded systems.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
LKML-Reference: <1265758732-19320-1-git-send-email-cascardo@holoscopio.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
x86/mm is on 32-rc4 and missing the spinlock namespace changes which
are needed for further commits into this topic.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Finally we can use early_res to replace bootmem for x86_64 now.
Still can use CONFIG_NO_BOOTMEM to enable it or not.
-v2: fix 32bit compiling about MAX_DMA32_PFN
-v3: folded bug fix from LKML message below
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4B747239.4070907@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
64bit NUMA already make enough space under 4G with new early_node_mem.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-16-git-send-email-yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Simplify setup_node_mem: don't use bootmem from other node, instead
just find_e820_area in early_node_mem.
This keeps the boundary between early_res and boot mem more clear, and
lets us only call early_res_to_bootmem() one time instead of for all
nodes.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-12-git-send-email-yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
In preparation for moving to the generic page_is_ram(), make explicit
what we expect to be reserved and not reserved.
Tested-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <20100122033004.335813103@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Commit 6aa542a694 added a quirk for the
Intel DG45ID board due to low memory corruption. The Intel DG45FC
shares the same BIOS (and the same bug) as noted in:
http://bugzilla.kernel.org/show_bug.cgi?id=13736
Signed-off-by: David Härdeman <david@hardeman.nu>
LKML-Reference: <20100128200254.GA9134@hardeman.nu>
Cc: <stable@kernel.org>
Cc: Alexey Fisher <bug-track@fisher-privat.net>
Cc: ykzhao <yakui.zhao@intel.com>
Cc: Tony Bones <aabonesml@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Jens found the following crash/regression:
[ 0.000000] found SMP MP-table at [ffff8800000fdd80] fdd80
[ 0.000000] Kernel panic - not syncing: Overlapping early reservations 12-f011 MP-table mpc to 0-fff BIOS data page
and
[ 0.000000] Kernel panic - not syncing: Overlapping early reservations 12-f011 MP-table mpc to 6000-7fff TRAMPOLINE
and bisected it to b24c2a9 ("x86: Move find_smp_config()
earlier and avoid bootmem usage").
It turns out the BIOS is using the first 64k for mptable,
without reserving it.
So try to find good range for the real-mode trampoline instead of
hard coding it, in case some bios tries to use that range for sth.
Reported-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Tested-by: Jens Axboe <jens.axboe@oracle.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
LKML-Reference: <4B21630A.6000308@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (36 commits)
x86, mm: Correct the implementation of is_untracked_pat_range()
x86/pat: Trivial: don't create debugfs for memtype if pat is disabled
x86, mtrr: Fix sorting of mtrr after subtracting
x86: Move find_smp_config() earlier and avoid bootmem usage
x86, platform: Change is_untracked_pat_range() to bool; cleanup init
x86: Change is_ISA_range() into an inline function
x86, mm: is_untracked_pat_range() takes a normal semiclosed range
x86, mm: Call is_untracked_pat_range() rather than is_ISA_range()
x86: UV SGI: Don't track GRU space in PAT
x86: SGI UV: Fix BAU initialization
x86, numa: Use near(er) online node instead of roundrobin for NUMA
x86, numa, bootmem: Only free bootmem on NUMA failure path
x86: Change crash kernel to reserve via reserve_early()
x86: Eliminate redundant/contradicting cache line size config options
x86: When cleaning MTRRs, do not fold WP into UC
x86: remove "extern" from function prototypes in <asm/proto.h>
x86, mm: Report state of NX protections during boot
x86, mm: Clean up and simplify NX enablement
x86, pageattr: Make set_memory_(x|nx) aware of NX support
x86, sleep: Always save the value of EFER
...
Fix up conflicts (added both iommu_shutdown and is_untracked_pat_range)
to 'struct x86_platform_ops') in
arch/x86/include/asm/x86_init.h
arch/x86/kernel/x86_init.c
* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Fix a section mismatch in arch/x86/kernel/setup.c
x86: Fixup last users of irq_chip->typename
x86: Remove BKL from apm_32
x86: Remove BKL from microcode
x86: use kernel_stack_pointer() in kprobes.c
x86: use kernel_stack_pointer() in kgdb.c
x86: use kernel_stack_pointer() in dumpstack.c
x86: use kernel_stack_pointer() in process_32.c
copy_edd() should be __init.
warning msg:
WARNING: vmlinux.o(.text+0x7759): Section mismatch in reference from the
function copy_edd() to the variable .init.data:boot_params
The function copy_edd() references
the variable __initdata boot_params.
This is often because copy_edd lacks a __initdata
annotation or the annotation of boot_params is wrong.
Signed-off-by: ZhenwenXu <helight.xu@gmail.com>
LKML-Reference: <4B139F8F.4000907@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Move the find_smp_config() call to before bootmem is initialized.
Use reserve_early() instead of reserve_bootmem() in it.
This simplifies the code, we only need to call find_smp_config()
once and can remove the now unneeded reserve parameter from
x86_init_mpparse::find_smp_config.
We thus also reduce x86's dependency on bootmem allocations.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4B0BB9F2.70907@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
use find_e820_area()/reserve_early() instead.
-v2: address Eric's request, to restore original semantics.
will fail, if the provided address can not be used.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
LKML-Reference: <4B09E2F9.7040403@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
It is possible for x86_64 systems to lack the NX bit either due to the
hardware lacking support or the BIOS having turned off the CPU capability,
so NX status should be reported. Additionally, anyone booting NX-capable
CPUs in 32bit mode without PAE will lack NX functionality, so this change
provides feedback for that case as well.
Signed-off-by: Kees Cook <kees.cook@canonical.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
LKML-Reference: <1258154897-6770-6-git-send-email-hpa@zytor.com>
The 32- and 64-bit code used very different mechanisms for enabling
NX, but even the 32-bit code was enabling NX in head_32.S if it is
available. Furthermore, we had a bewildering collection of tests for
the available of NX.
This patch:
a) merges the 32-bit set_nx() and the 64-bit check_efer() function
into a single x86_configure_nx() function. EFER control is left
to the head code.
b) eliminates the nx_enabled variable entirely. Things that need to
test for NX enablement can verify __supported_pte_mask directly,
and cpu_has_nx gives the supported status of NX.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Vegard Nossum <vegardno@ifi.uio.no>
Cc: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Chris Wright <chrisw@sous-sol.org>
LKML-Reference: <1258154897-6770-5-git-send-email-hpa@zytor.com>
Acked-by: Kees Cook <kees.cook@canonical.com>
Instead of using bootmem, try find_e820_area()/reserve_early(),
and call acpi_reserve_memory() early, to allocate the wakeup
trampoline code area below 1M.
This is more reliable, and it also removes a dependency on
bootmem.
-v2: change function name to acpi_reserve_wakeup_memory(),
as suggested by Rafael.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: pm list <linux-pm@lists.linux-foundation.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <4AFA210B.3020207@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On platforms where the BIOS handles the thermal monitor interrupt,
APIC_LVTTHMR on each logical CPU is programmed to generate a SMI
and OS must not touch it.
Unfortunately AP bringup sequence using INIT-SIPI-SIPI clears all
the LVT entries except the mask bit. Essentially this results in
all LVT entries including the thermal monitoring interrupt set
to masked (clearing the bios programmed value for APIC_LVTTHMR).
And this leads to kernel take over the thermal monitoring
interrupt on AP's but not on BSP (leaving the bios programmed
value only on BSP).
As a result of this, we have seen system hangs when the thermal
monitoring interrupt is generated.
Fix this by reading the initial value of thermal LVT entry on
BSP and if bios has taken over the control, then program the
same value on all AP's and leave the thermal monitoring
interrupt control on all the logical cpu's to the bios.
Signed-off-by: Yong Wang <yong.y.wang@intel.com>
Reviewed-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Cc: Arjan van de Ven <arjan@infradead.org>
LKML-Reference: <20091110013824.GA24940@ywang-moblin2.bj.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: stable@kernel.org
We have a board with a Phoenix/MSC BIOS which also corrupts the low
64KB of RAM, so add an entry to the table.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
LKML-Reference: <20091106154404.002648d9@marrow.netinsight.se>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This is the counterpart to "x86: export k8 physical topology" for
SRAT. It is not as invasive because the acpi code already seperates
node setup into detection and registration steps, with the
exception of registering e820 active regions in
acpi_numa_memory_affinity_init(). This is now moved to
acpi_scan_nodes() if NUMA emulation is disabled or deferred.
acpi_numa_init() now returns a value which specifies whether an
underlying SRAT was located. If so, that topology can be used by
the emulation code to interleave emulated nodes over physical nodes
or to register the nodes for ACPI.
acpi_get_nodes() may now be used to export the srat physical
topology of the machine for NUMA emulation.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: Ankita Garg <ankita@in.ibm.com>
Cc: Len Brown <len.brown@intel.com>
LKML-Reference: <alpine.DEB.1.00.0909251518580.14754@chino.kir.corp.google.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
To eventually interleave emulated nodes over physical nodes, we
need to know the physical topology of the machine without actually
registering it. This does the k8 node setup in two parts:
detection and registration. NUMA emulation can then used the
physical topology detected to setup the address ranges of emulated
nodes accordingly. If emulation isn't used, the k8 nodes are
registered as normal.
Two formals are added to the x86 NUMA setup functions: `acpi' and
`k8'. These represent whether ACPI or K8 NUMA has been detected;
both cannot be true at the same time. This specifies to the NUMA
emulation code whether an underlying physical NUMA topology exists
and which interface to use.
This patch deals solely with separating the k8 setup path into
Northbridge detection and registration steps and leaves the ACPI
changes for a subsequent patch. The `acpi' formal is added here,
however, to avoid touching all the header files again in the next
patch.
This approach also ensures emulated nodes will not span physical
nodes so the true memory latency is not misrepresented.
k8_get_nodes() may now be used to export the k8 physical topology
of the machine for NUMA emulation.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: Ankita Garg <ankita@in.ibm.com>
Cc: Len Brown <len.brown@intel.com>
LKML-Reference: <alpine.DEB.1.00.0909251518400.14754@chino.kir.corp.google.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
After close looking, commit 8126dec3 will break:
1. some cpu feature in early stage too, like cpu_has_x2apic
2. will break built-in-command line
3. will break other memmap= and mem=
4. early_dbgp and early_console that will use early_ioremap to access mmio (?)
So revert it.
Reported-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>,
Cc: Linus Torvalds <torvalds@linux-foundation.org>,
Cc: Andrew Morton <akpm@linux-foundation.org>,
LKML-Reference: <4AB51DFD.2000904@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (38 commits)
x86: Move get/set_wallclock to x86_platform_ops
x86: platform: Fix section annotations
x86: apic namespace cleanup
x86: Distangle ioapic and i8259
x86: Add Moorestown early detection
x86: Add hardware_subarch ID for Moorestown
x86: Add early platform detection
x86: Move tsc_init to late_time_init
x86: Move tsc_calibration to x86_init_ops
x86: Replace the now identical time_32/64.c by time.c
x86: time_32/64.c unify profile_pc
x86: Move calibrate_cpu to tsc.c
x86: Make timer setup and global variables the same in time_32/64.c
x86: Remove mca bus ifdef from timer interrupt
x86: Simplify timer_ack magic in time_32.c
x86: Prepare unification of time_32/64.c
x86: Remove do_timer hook
x86: Add timer_init to x86_init_ops
x86: Move percpu clockevents setup to x86_init_ops
x86: Move xen_post_allocator_init into xen_pagetable_setup_done
...
Fix up conflicts in arch/x86/include/asm/io_apic.h
* 'x86-pat-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, pat: Fix cacheflush address in change_page_attr_set_clr()
mm: remove !NUMA condition from PAGEFLAGS_EXTENDED condition set
x86: Fix earlyprintk=dbgp for machines without NX
x86, pat: Sanity check remap_pfn_range for RAM region
x86, pat: Lookup the protection from memtype list on vm_insert_pfn()
x86, pat: Add lookup_memtype to get the current memtype of a paddr
x86, pat: Use page flags to track memtypes of RAM pages
x86, pat: Generalize the use of page flag PG_uncached
x86, pat: Add rbtree to do quick lookup in memtype tracking
x86, pat: Add PAT reserve free to io_mapping* APIs
x86, pat: New i/f for driver to request memtype for IO regions
x86, pat: ioremap to follow same PAT restrictions as other PAT users
x86, pat: Keep identity maps consistent with mmaps even when pat_disabled
x86, mtrr: make mtrr_aps_delayed_init static bool
x86, pat/mtrr: Rendezvous all the cpus for MTRR/PAT init
generic-ipi: Allow cpus not yet online to call smp_call_function with irqs disabled
x86: Fix an incorrect argument of reserve_bootmem()
x86: Fix system crash when loading with "reservetop" parameter
Conflicts:
arch/x86/kernel/reboot.c
security/Kconfig
Merge reason: resolve the conflicts, bump up from rc3 to rc8.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Move tboot.h from asm to linux to fix the build errors of intel_txt
patch on non-X86 platforms. Remove the tboot code from generic code
init/main.c and kernel/cpu.c.
Signed-off-by: Shane Wang <shane.wang@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
boot_cpu_physical_apicid is a global variable and used as function
argument as well. Rename the function arguments to avoid confusion.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
TSC calibration is modified by the vmware hypervisor and paravirt by
separate means. Moorestown wants to add its own calibration routine as
well. So make calibrate_tsc a proper x86_init_ops function and
override it by paravirt or by the early setup of the vmware
hypervisor.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The timer init code is convoluted with several quirks and the paravirt
timer chooser. Figuring out which code path is actually taken is not
for the faint hearted.
Move the numaq TSC quirk to tsc_pre_init x86_init_ops function and
replace the paravirt time chooser and the remaining x86 quirk with a
simple x86_init_ops function.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We really do not need two paravirt/x86_init_ops functions which are
called in two consecutive source lines. Move the only user of
post_allocator_init into the already existing pagetable_setup_done
function.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Replace another obscure paravirt magic and move it to
x86_init_ops. Such a hook is also useful for embedded and special
hardware.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
ARCH_SETUP is a horrible leftover from the old arch/i386 mach support
code. It still has a lonely user in xen. Move it to x86_init_ops.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
irq_init is overridden by x86_quirks and by paravirts. Unify the whole
mess and make it an unconditional x86_init_ops function which defaults
to the standard function and can be overridden by the early platform
code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Replace the quirk machinery by a x86_init_ops function which defaults
to the standard implementation.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Since parse_early_param() may (e.g. for earlyprintk=dbgp)
involve calls to page table manipulation functions (here
set_fixmap_nocache()), NX hardware support must be determined
before calling that function (so that __supported_pte_mask gets
properly set up).
But the call after parse_early_param() can also not go away, as
that will honor eventual command line specified disabling of
the NX functionality.
( This will then just result in whatever mappings got
established during parse_early_param() having the NX bit set
despite it being disabled on the command line, but I think
that's tolerable).
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
LKML-Reference: <4A97F3BD02000078000121B9@vpn.id2.novell.com>
[ merged to x86/pat to resolve a conflict. ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
arch/x86/kernel/sfi.c serves the dual-purpose of supporting the
SFI core with arch specific code, as well as a home for the
arch-specific code that uses SFI.
analogous to ACPI, drivers/sfi/Kconfig is pulled in by arch/x86/Kconfig
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Cc: x86@kernel.org
The 32bit and the 64bit code are slighty different in the reservation
of standard resources. Also the upcoming Moorestown support needs its
own version of that.
Add it to x86_init_ops and initialize it with the 64bit default. 32bit
overrides it in early boot. Now moorestown can add it's own override
w/o sprinkling the code with more #ifdefs
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
probe_roms is only used on 32bit. Add it to the x86_init ops and
remove the #ifdefs.
Default initializer is x86_init_noop() which is overridden in
the 32bit boot code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The system will die if the kernel is booted with "reservetop"
parameter, in present code, parse "reservetop" parameter after
early_ioremap_init(), and some function still use
early_ioremap() after it.
The problem is, "reservetop" parameter can modify
'FIXADDR_TOP', then the virtual address got by early_ioremap()
is base on old 'FIXADDR_TOP', but the page mapping is base on
new 'FIXADDR_TOP', it will occur page fault, and the IDT is not
prepare yet, so, the system is dead.
So, put parse_early_param() in the front of
early_ioremap_init() in this patch.
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Cc: yinghai@kernel.org
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <4A8D402F.4080805@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch adds kernel configuration and boot support for Intel Trusted
Execution Technology (Intel TXT).
Intel's technology for safer computing, Intel Trusted Execution
Technology (Intel TXT), defines platform-level enhancements that
provide the building blocks for creating trusted platforms.
Intel TXT was formerly known by the code name LaGrande Technology (LT).
Intel TXT in Brief:
o Provides dynamic root of trust for measurement (DRTM)
o Data protection in case of improper shutdown
o Measurement and verification of launched environment
Intel TXT is part of the vPro(TM) brand and is also available some
non-vPro systems. It is currently available on desktop systems based on
the Q35, X38, Q45, and Q43 Express chipsets (e.g. Dell Optiplex 755, HP
dc7800, etc.) and mobile systems based on the GM45, PM45, and GS45
Express chipsets.
For more information, see http://www.intel.com/technology/security/.
This site also has a link to the Intel TXT MLE Developers Manual, which
has been updated for the new released platforms.
A much more complete description of how these patches support TXT, how to
configure a system for it, etc. is in the Documentation/intel_txt.txt file
in this patch.
This patch provides the TXT support routines for complete functionality,
documentation for TXT support and for the changes to the boot_params structure,
and boot detection of a TXT launch. Attempts to shutdown (reboot, Sx) the system
will result in platform resets; subsequent patches will support these shutdown modes
properly.
Documentation/intel_txt.txt | 210 +++++++++++++++++++++
Documentation/x86/zero-page.txt | 1
arch/x86/include/asm/bootparam.h | 3
arch/x86/include/asm/fixmap.h | 3
arch/x86/include/asm/tboot.h | 197 ++++++++++++++++++++
arch/x86/kernel/Makefile | 1
arch/x86/kernel/setup.c | 4
arch/x86/kernel/tboot.c | 379 +++++++++++++++++++++++++++++++++++++++
security/Kconfig | 30 +++
9 files changed, 827 insertions(+), 1 deletion(-)
Signed-off-by: Joseph Cihula <joseph.cihula@intel.com>
Signed-off-by: Shane Wang <shane.wang@intel.com>
Signed-off-by: Gang Wei <gang.wei@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
AMI BIOS with low memory corruption was found on Intel DG45ID
board (Bug 13710). Add this board to the blacklist - in the
(somewhat optimistic) hope of future boards/BIOSes from Intel
not having this bug.
Also see:
http://bugzilla.kernel.org/show_bug.cgi?id=13736
Signed-off-by: Alexey Fisher <bug-track@fisher-privat.net>
Cc: ykzhao <yakui.zhao@intel.com>
Cc: alan@lxorguk.ukuu.org.uk
Cc: <stable@kernel.org>
LKML-Reference: <1247660169-4503-1-git-send-email-bug-track@fisher-privat.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The init_gbpages() function is conditionally called from
init_memory_mapping() function. There are two call-sites where
this 'after_bootmem' condition can be true: setup_arch() and
mem_init() via pci_iommu_alloc().
Therefore, it's safe to move the call to init_gbpages() to
setup_arch() as it's always called before mem_init().
This removes an after_bootmem use - paving the way to remove
all uses of that state variable.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <Pine.LNX.4.64.0906221731210.19474@melkki.cs.Helsinki.FI>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On a system where system memory (according e820) is not covered by
mtrr, mtrr_trim_memory converts a portion of memory to reserved, but
bootloader has already put the initrd in that range.
Thus, we need to have 64bit to use relocate_initrd too.
[ Impact: fix using initrd when mtrr_trim_memory happen ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: stable@kernel.org
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (22 commits)
x86: fix system without memory on node0
x86, mm: Fix node_possible_map logic
mm, x86: remove MEMORY_HOTPLUG_RESERVE related code
x86: make sparse mem work in non-NUMA mode
x86: process.c, remove useless headers
x86: merge process.c a bit
x86: use sparse_memory_present_with_active_regions() on UMA
x86: unify 64-bit UMA and NUMA paging_init()
x86: Allow 1MB of slack between the e820 map and SRAT, not 4GB
x86: Sanity check the e820 against the SRAT table using e820 map only
x86: clean up and and print out initial max_pfn_mapped
x86/pci: remove rounding quirk from e820_setup_gap()
x86, e820, pci: reserve extra free space near end of RAM
x86: fix typo in address space documentation
x86: 46 bit physical address support on 64 bits
x86, mm: fault.c, use printk_once() in is_errata93()
x86: move per-cpu mmu_gathers to mm/init.c
x86: move max_pfn_mapped and max_low_pfn_mapped to setup.c
x86: unify noexec handling
x86: remove (null) in /sys kernel_page_tables
...
* 'x86-kbuild-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (46 commits)
x86, boot: add new generated files to the appropriate .gitignore files
x86, boot: correct the calculation of ZO_INIT_SIZE
x86-64: align __PHYSICAL_START, remove __KERNEL_ALIGN
x86, boot: correct sanity checks in boot/compressed/misc.c
x86: add extension fields for bootloader type and version
x86, defconfig: update kernel position parameters
x86, defconfig: update to current, no material changes
x86: make CONFIG_RELOCATABLE the default
x86: default CONFIG_PHYSICAL_START and CONFIG_PHYSICAL_ALIGN to 16 MB
x86: document new bzImage fields
x86, boot: make kernel_alignment adjustable; new bzImage fields
x86, boot: remove dead code from boot/compressed/head_*.S
x86, boot: use LOAD_PHYSICAL_ADDR on 64 bits
x86, boot: make symbols from the main vmlinux available
x86, boot: determine compressed code offset at compile time
x86, boot: use appropriate rep string for move and clear
x86, boot: zero EFLAGS on 32 bits
x86, boot: set up the decompression stack as early as possible
x86, boot: straighten out ranges to copy/zero in compressed/head*.S
x86, boot: stylistic cleanups for boot/compressed/head_64.S
...
Fixed trivial conflict in arch/x86/configs/x86_64_defconfig manually
A long ago, in days of yore, it all began with a god named Thor.
There were vikings and boats and some plans for a Linux kernel
header. Unfortunately, a single 8-bit field was used for bootloader
type and version. This has generally worked without *too* much pain,
but we're getting close to flat running out of ID fields.
Add extension fields for both type and version. The type will be
extended if it the old field is 0xE; the version is a simple MSB
extension.
Keep /proc/sys/kernel/bootloader_type containing
(type << 4) + (ver & 0xf) for backwards compatiblity, but also add
/proc/sys/kernel/bootloader_version which contains the full version
number.
[ Impact: new feature to support more bootloaders ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Do this so we can check the range that is mapped before
init_memory_mapping().
To be able to print out meaningful info, we first have to fix
64-bit to have max_pfn_mapped assigned before that call. This
also unifies the code-path a bit.
[ Impact: print more debug info, cleanup ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <49BF0978.40605@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch moves the max_pfn_mapped and max_low_pfn_mapped global
variables to kernel/setup.c where they're initialized.
[ Impact: cleanup ]
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
LKML-Reference: <1240923649.1982.21.camel@penberg-laptop>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
In preparation for unifying irqinit_{32,64}.c, make
x86_quirk_pre_intr_init() local to irqinit_32.c.
Reviewed-by Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
It's unused, since about 1995. So remove all initialization of it in
preparation for actually removing the field.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Impact: new interface; remove hard-coded limit
Add RESERVE_BRK(name, size) macro to reserve space in the brk
area. This should be a conservative (ie, larger) estimate of
how much space might possibly be required from the brk area.
Any unused space will be freed, so there's no real downside
on making the reservation too large (within limits).
The name should be unique within a given file, and somewhat
descriptive.
The C definition of RESERVE_BRK() ends up being more complex than
one would expect to work around a cluster of gcc infelicities:
The first attempt was to simply try putting __section(.brk_reservation)
on a variable. This doesn't work because it ends up making it a
@progbits section, which gets actual space allocated in the vmlinux
executable.
The second attempt was to emit the space into a section using asm,
but gcc doesn't allow arguments to be passed to file-level asm()
statements, making it hard to pass in the size.
The final attempt is to wrap the asm() in a function to allow
it to have arguments, and put the function itself into the
.discard section, which vmlinux*.lds drops entirely from the
emitted vmlinux.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: use new interface instead of previous ad hoc implementation
Use extend_brk() to allocate memory for DMI rather than having an
ad-hoc allocator.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: use new interface instead of previous ad hoc implementation
Rather than having special purpose init_pg_table_start/end variables
to delimit the kernel pagetable built by head_32.S, just use the brk
mechanism to extend the bss for the new pagetable.
This patch removes init_pg_table_start/end and pg0, defines __brk_base
(which is page-aligned and immediately follows _end), initializes
the brk region to start there, and uses it for the 32-bit pagetable.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: build fix
The brk initialization functions were incorrectly located inside
an #ifdef CONFIG_VLK_DEV_INITRD block, causing the obvious build failure in
minimal configurations.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Impact: new interface
Add a brk()-like allocator which effectively extends the bss in order
to allow very early code to do dynamic allocations. This is better than
using statically allocated arrays for data in subsystems which may never
get used.
The space for brk allocations is in the bss ELF segment, so that the
space is mapped properly by the code which maps the kernel, and so
that bootloaders keep the space free rather than putting a ramdisk or
something into it.
The bss itself, delimited by __bss_stop, ends before the brk area
(__brk_base to __brk_limit). The kernel text, data and bss is reserved
up to __bss_stop.
Any brk-allocated data is reserved separately just before the kernel
pagetable is built, as that code allocates from unreserved spaces
in the e820 map, potentially allocating from any unused brk memory.
Ultimately any unused memory in the brk area is used in the general
kernel memory pool.
Initially the brk space is set to 1MB, which is probably much larger
than any user needs (the largest current user is i386 head_32.S's code
to build the pagetables to map the kernel, which can get fairly large
with a big kernel image and no PSE support). So long as the system
has sufficient memory for the bootloader to reserve the kernel+1MB brk,
there are no bad effects resulting from an over-large brk.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: cleanup, micro-optimization
Pre-initialize boot_cpu_data.x86_phys_bits to a reasonable default
to remove the use of system_state tests in __virt_addr_valid()
and __phys_addr().
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: reactivate DMI quirks on EFI hardware
DMI tables are loaded by EFI, so the dmi calls must happen after
efi_init() and not before.
Currently Apple hardware uses DMI to determine the framebuffer mappings
for efifb. Without DMI working you also have no video on MacBook Pro.
This patch resolves the DMI issue for EFI hardware (DMI is now properly
detected at boot), and additionally efifb now loads on Apple hardware
(i.e. video works).
Signed-off-by: Brian Maly <bmaly@redhat>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Cc: ying.huang@intel.com
LKML-Reference: <49ADEDA3.1030406@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
arch/x86/kernel/setup.c | 5 +++--
1 file changed, 3 insertions(+), 2 deletions(-)
Impact: cleanup
that is only needed when CONFIG_X86_VSMP is defined with 64bit
also remove dead code about PCI, because CONFIG_X86_VSMP depends on PCI
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
x86_quirks->update_apic() calling looks crazy. so try to remove it:
1. every apic take wakeup_cpu member directly
2. separate es7000_apic to es7000_apic_cluster
3. use uv_wakeup_cpu directly
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
Make x86_quirks support more transparent. The highlevel
methods are now named:
extern void x86_quirk_pre_intr_init(void);
extern void x86_quirk_intr_init(void);
extern void x86_quirk_trap_init(void);
extern void x86_quirk_pre_time_init(void);
extern void x86_quirk_time_init(void);
This makes it clear that if some platform extension has to
do something here that it is considered ... weird, and is
discouraged.
Also remove arch_hooks.h and move it into setup.h (and other
header files where appropriate).
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: remove dead code
Remove:
- pre_setup_arch_hook()
- mca_nmi_hook()
If needed they can be added back via an x86_quirk handler.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: build fix, cleanup
A couple of arch setup callbacks were mistakenly in apic_32.c, breaking
the build.
Also simplify the code a bit.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
Now that all APIC code is consolidated there's nothing 'gen' about
apics anymore - so rename 'struct genapic' to 'struct apic'.
This shortens the code and is nicer to read as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
so could deselect x2apic
and INTR_REMAP will select x2apic
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
With refactoring of wake_cpu macros the 32bit code in tip doesn't
execute generic_apic_probe if CONFIG_X86_32_NON_STANDARD is not set.
Even on a x86 STANDARD cpu we need to execute the generic_apic_probe
function, as we rely on this function to execute the update_genapic
quirk which initilizes apic->wakeup_cpu.
Failing to do so results in we making a call to a null function in do_boot_cpu.
The stack trace without the patch goes like this.
Booting processor 1 APIC 0x1 ip 0x6000
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<(null)>] (null)
*pdpt = 0000000000839001 *pde = 0000000000c97067 *pte = 0000000000000163
Oops: 0000 [#1] SMP
last sysfs file:
Modules linked in:
Pid: 1, comm: swapper Not tainted (2.6.29-rc4-tip #18) VMware Virtual Platform
EIP: 0062:[<00000000>] EFLAGS: 00010293 CPU: 0
EIP is at 0x0
EAX: 00000001 EBX: 00006000 ECX: c077ed00 EDX: 00006000
ESI: 00000001 EDI: 00000001 EBP: ef04cf40 ESP: ef04cf1c
DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 006a
Process swapper (pid: 1, ti=ef04c000 task=ef050000 task.ti=ef04c000)
Stack:
c0644e52 00000000 ef04cf24 ef04cf24 c064468d c0886dc0 00000000 c0702aea
ef055480 00000001 00000101 dead4ead ffffffff ffffffff c08af530 00000000
c0709715 ef04cf60 ef04cf60 00000001 00000000 00000000 dead4ead ffffffff
Call Trace:
[<c0644e52>] ? native_cpu_up+0x2de/0x45b
[<c064468d>] ? do_fork_idle+0x0/0x19
[<c0645c5e>] ? _cpu_up+0x88/0xe8
[<c0645d20>] ? cpu_up+0x42/0x4e
[<c07e7462>] ? kernel_init+0x99/0x14b
[<c07e73c9>] ? kernel_init+0x0/0x14b
[<c040375f>] ? kernel_thread_helper+0x7/0x10
Code: Bad EIP value.
EIP: [<00000000>] 0x0 SS:ESP 006a:ef04cf1c
I think we should call generic_apic_probe unconditionally for 32 bit now.
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
just like 64 bit switch from flat logical APIC messages to
flat physical mode automatically.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
X86_GENERICARCH is a misnomer - it contains non-PC 32-bit architectures
that are not included in the default build.
Rename it to X86_32_NON_STANDARD.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Yinghai Lu