The advent of DIF Type 2 devices exposed some missing break statements
in the protection mask switch constructs. However, rewriting the code
to use an index into a small static array seemed like a more elegant
solution.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch contains changes that allow iscsi_session_setup
to allocate private space for LLD's
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Acked-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Disks formatted with DIF Type 2 reject READ/WRITE 6/10/12/16 commands
when protection is enabled. Only the 32-byte variants are supported.
Implement support for issusing 32-byte READ/WRITE and enable Type 2
drives in the protection type detection logic.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
So far we have only issued DIF commands if CONFIG_BLK_DEV_INTEGRITY is
enabled. However, communication between initiator and target should be
independent of protection information DMA. There are DIF-only host
adapters coming out that will be able to take advantage of this.
Move the relevant DIF bits to sd.c.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The checksum format is orthogonal to whether the protection information
is being passed on beyond the HBA or not. It is perfectly valid to use
a non-T10 CRC with WRITE_STRIP and READ_INSERT.
Consequently it no longer makes sense to explicitly refer to the
conversion in the protection operation. Update sd_dif and lpfc
accordingly.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Ihab Hamadi <Ihab.Hamadi@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
bnx2i currently has a check for if a ep is properly bound, so if
iscsi_queuecommand/xmit_task is called while there is no ep
we will not queue IO.
be2iscsi sends IO from queuecommand/xmit_task like how bnx2i does
and needs a similar test. This patch has us just use the suspend_bit
test for this.
When ep_poll has succeeed iscsid will call conn_bind, the LLD will
then call iscsi_conn_bind which will clear the suspend bit.
When ep_disconnect is called (or if there is a conn error) we set
the suspend bit. For the ep_disconnect case I am adding a helper
in this patch that will take the session lock to make sure
iscsi_queuecommand/xmit_task is not running and it will set
the suspend bit.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
beiscsi does not need the iscsi scsi cmd processing. It does not
even get this info on the completion path. This adds a function
to just update the sequencing numbers and complete a task.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When an RSCN indicates changes to individual remote ports,
don't blindly log them out and then back in. Instead, determine
whether they're still in the directory, by doing GPN_ID.
If that is successful, call login, which will send ADISC and reverify,
otherwise, call logoff. Perhaps we should just delete the rport,
not send LOGO, but it seems safer.
Also, fix a possible issue where if a mix of records in the RSCN
cause us to queue disc_ports for disc_single and then we decide
to do full rediscovery, we leak memory for those disc_ports queued.
So, go through the list of disc_ports even if doing full discovery.
Free the disc_ports in any case. If any of the disc_single() calls
return error, do a full discovery.
The ability to fill in GPN_ID requests was added to fc_ct_fill().
For this, it needs the FC_ID to be passed in as an arg.
The did parameter for fc_elsct_send() is used for that, since the
actual D_DID will always be 0xfffffc for all CT requests so far.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When rport_login is called on an rport that is already thought
to be logged in, use ADISC. If that fails, redo PLOGI.
This is less disruptive after fabric changes that don't affect
the state of the target.
Implement the sending of ADISC via fc_els_fill.
Add ADISC state to the rport state machine. This is entered from READY
and returns to READY after successful completion. If it fails, the rport
is either logged off and deleted or re-does PLOGI.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Improve lport and rport debug messages to indicate whether
the response is LS_ACC, LS_RJT, closed, or timeout.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This moves the remote port lookup for incoming ELS requests into
fc_rport.c, in preparation for handing PLOGI and LOGO from
unknown rports.
This changes the arg to rport_recv_req from an rdata to an lport.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Currently these values are initialized by the callers. This was exposed
by a later patch that adds PLOGI request support. The patch failed to
initialize the new remote port's roles and it caused problems. This patch
has the rport_create routine initialize the identifiers and then the
callers can override them with real values.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
On some switches, an empty zone causes GPN_FT to be rejected
with reason 9 (unable) explanation 7 (FC-4 types not registered),
which causes discovery to be retried endlessly. Treat this as
just an empty response and consider discovery complete.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When receiving an RSCN, do not log off all rports. This is
extremely disruptive. If, after the GPN_FT response, some
rports haven't been listed, delete them.
Add field disc_id to structs fc_rport_priv and fc_disc.
disc_id is an arbitrary serial number used to identify the
rports found by the latest discovery. This eliminates the need
to go through the rport list when restarting discovery.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Delete unused disc->delay element.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
There was no need to have the discovery status stored in struct fc_disc.
Change fc_disc_done() to take the discovery status as an argument
and just pass it on to the discovery callback.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Don't create a "dummy" remote port to go with fc_rport_priv.
Make the rport truly optional by allocating fc_rport_priv separately
and not requiring a dummy rport to be there if we haven't yet done
fc_remote_port_add().
The fc_rport_libfc_priv remains as a structure attached to the
rport for I/O purposes.
Be sure to hold references on rdata when the lock is dropped in
fc_rport_work().
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Remote ports will become READY more than once after
ADISC is implemented in a later patch.
The event callback that has been called "CREATED" will mean "READY".
Rename it now in preparation for those changes.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Allow a struct fc_rport_priv to have no fc_rport associated with it.
This sets up to remove the need for "rogue" rports.
Add a few fields to fc_rport_priv that are needed before the fc_rport
is created. These are the ids, maxframe_size, classes, and rport pointer.
Remove the macro PRIV_TO_RPORT(). Just use rdata->rport where appropriate.
To take the place of the get_device()/put_device ops that were used to
hold both the rport and rdata, add a reference count to rdata structures
using kref. When kref_get decrements the refcount to zero, a new template
function releasing the rdata should be called. This will take care of
freeing the rdata and releasing the hold on the rport (for now). After
subsequent patches make the rport truly optional, this release function
will simply free the rdata.
Remove the simple inline function fc_rport_set_name(), which becomes
semanticly ambiguous otherwise. The caller will set the port_name and
node_name in the rdata->Ids, which will later be copied to the rport
when it its created.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
tt.elsct_send is used by both FCP and by the rport state machine.
After further patches, these two modules will use different
structures for the remote port.
So, change elsct_send to use the FC_ID instead of the fc_rport_priv
as its argument. It currently only uses the FC_ID anyway.
For CT requests the destination FC_ID is still implicitly 0xfffffc.
After further patches the did arg on CT requests will be used to
specify the FC_ID being inquired about for GPN_ID or other queries.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The rport and discovery modules deal with remote ports
before fc_remote_port_add() can be done, because the
full set of rport identifiers is not known at early stages.
In preparation for splitting the fc_rport/fc_rport_priv allocation,
make fc_rport_priv the primary interface for the remote port and
discovery engines.
The FCP / SCSI layers still deal with fc_rport and
fc_rport_libfc_priv, however.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
These macros introduce extra undesirable semicolons that keep
them from being used in expressions, and they don't protect
against being passed an expression.
Add parens and remove the semicolons.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The interface for lport->tt.rport_create() takes a fc_disc_port arg,
which is unnatural for most calls. The only reason for this was
to avoid passing in the local port as an argument, but otherwise
added to complexity.
Simplify by just using lport and fc_rport_identifiers.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
While the I/O and LLD interfaces use fc_rport_libfc_priv, the
disc and rport interfaces will use fc_rport_priv, which will
be separately allocated.
Change the disc and rport usage of fc_rport_libfc_priv to fc_rport_priv.
Use #define temporarily to make both names equivalent until a
subsequent patch splits them.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
1. Updates fcoe_rcv() to queue incoming frames to the fcoe per
cpu thread on which this frame's exch was originated and simply
use current cpu for request exch not originated by initiator.
It is redundant to add this code under CONFIG_SMP, so removes
CONFIG_SMP uses around this code.
2. Updates fc_exch_em_alloc, fc_exch_delete, fc_exch_find to use
per cpu exch pools, here fc_exch_delete is rename of older
fc_exch_mgr_delete_ep since ep/exch are now deleted in pools
of EM and so brief new name is sufficient and better name.
Updates these functions to map exch id to their index into exch
pool using fc_cpu_mask, fc_cpu_order and EM min_xid.
This mapping is as per detailed explanation about this in
last patch and basically this is just as lower fc_cpu_mask
bits of exch id as cpu number and upper bit sum of EM min_xid
and exch index in pool.
Uses pool next_index to keep track of exch allocation from
pool along with pool_max_index as upper bound of exches array
in pool.
3. Adds exch pool ptr to fc_exch to free exch to its pool in
fc_exch_delete.
4. Updates fc_exch_mgr_reset to reset all exch pools of an EM,
this required adding fc_exch_pool_reset func to reset exches
in pool and then have fc_exch_mgr_reset call fc_exch_pool_reset
for each pool within each EM for a lport.
5. Removes no longer needed exches array, em_lock, next_xid, and
total_exches from struct fc_exch_mgr, these are not needed after
use of per cpu exch pool, also removes not used max_read,
last_read from struct fc_exch_mgr.
6. Updates locking notes for exch pool lock with fc_exch lock and
uses pool lock in exch allocation, lookup and reset.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Adds per cpu exch pool for these reasons:-
1. Currently an EM instance is shared across all cpus to manage
all exches for all cpus. This required em_lock across all
cpus for an exch alloc, free, lookup and reset each frame
and that made em_lock expensive, so instead having per cpu
exch pool with their own per cpu pool lock will likely reduce
locking contention in fast path for an exch alloc, free and
lookup.
2. Per cpu exch pool will likely improve cache hit ratio since
all frames of an exch will be processed on the same cpu on
which exch originated.
This patch is only prep work to help in keeping complexity of next
patch low, so this patch only sets up per cpu exch pool and related
helper funcs to be used by next patch. The next patch fully makes
use of per cpu exch pool in all code paths ie. tx, rx and reset.
Divides per EM exch id range equally across all cpus to setup per
cpu exch pool. This division is such that lower bits of exch id
carries cpu number info on which exch originated, later a simple
bitwise AND operation on exch id of incoming frame with fc_cpu_mask
retrieves cpu number info to direct all frames to same cpu on which
exch originated. This required a global fc_cpu_mask and fc_cpu_order
initialized to max possible cpus number nr_cpu_ids rounded up to 2's
power, this will be used in mapping exch id and exch ptr array
index in pool during exch allocation, find or reset code paths.
Adds a check in fc_exch_mgr_alloc() to ensure specified min_xid
lower bits are zero since these bits are used to carry cpu info.
Adds and initializes struct fc_exch_pool with all required fields
to manage exches in pool.
Allocates per cpu struct fc_exch_pool with memory for exches array
for range of exches per pool. The exches array memory is followed
by struct fc_exch_pool.
Adds fc_exch_ptr_get/set() helper functions to get/set exch ptr in
pool exches array at specified array index.
Increases default FCOE_MAX_XID to 0x0FFF from 0x07EF, so that more
exches are available per cpu after above described exch id range
division across all cpus to each pool.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
If a target closed the connection, we will detect it in the
state_changed or data_ready callout. This adds a new conn
error value to use for this problem, so it is not confused
with when the initiator throws a conn error and drops
the connection.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When we moved the device handler functionality from dm layer to SCSI layer
we dropped the parameter functionality.
This path adds an interface to scsi dh layer to set device handler
parameters.
Basically, multipath layer need to create a string with all the parameters
and call scsi_dh_set_params() after it called scsi_dh_attach() on a
device.
If a device handler provides such an interface it will handle the parameters
as it expects them.
Reported-by: Eddie Williams <Eddie.Williams@steeleye.com>
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Tested-by: Eddie Williams <Eddie.Williams@steeleye.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
FC_FRAME_SG_LEN is 4 which is too small when offload is enabled. Actually, the
WARN_ON() in fc_fcp_send_data() should be:
WARN_ON(skb_shinfo(fp_skb(fp))->nr_frags > MAX_SKB_FRAGS);
But since we will not get anything more than 64K anyway, so there is no need
to do this anyway here. Therefore, I am getting rid of FC_FRAME_SG_LEN here
and the WARN_ON here.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Modifies current code to use EM anchor list in EM allocation, EM free,
EM reset, exch allocation and exch lookup code paths.
1. Modifies fc_exch_mgr_alloc to accept EM match function and then
have allocated EM added to the lport using fc_exch_mgr_add API
while also updating EM kref for newly added EM.
2. Updates fc_exch_mgr_free API to accept only lport pointer instead
EM and then have this API free all EMs of the lport from EM anchor
list.
3. Removes single lport pointer link from the EM, which was used in
associating lport pointer in newly allocated exchange. Instead have
lport pointer passed along new exchange allocation call path and
then store passed lport pointer in newly allocated exchange, this
will allow a single EM instance to be used across more than one
lport and used in EM reset to reset only lport specific exchanges.
4. Modifies fc_exch_mgr_reset to reset all EMs from the EM anchor list
of the lport, adds additional exch lport pointer (ep->lp) check for
shared EM case to reset exchange specific to a lport requested reset.
5. Updates exch allocation API fc_exch_alloc to use EM anchor list and
its anchor match func pointer. The fc_exch_alloc will walk the list
of EMs until it finds a match, a match will be either null match
func pointer or call to match function returning true value.
6. Updates fc_exch_recv to accept incoming frame on local port using
only lport pointer and frame pointer without specifying EM instance
of incoming frame. Instead modified fc_exch_recv to locate EM for the
incoming frame by matching xid of incoming frame against a EM xid range.
This change was required to use EM list in libfc Rx path and after this
change the lport fc_exch_mgr pointer emp is not needed anymore, so
removed emp pointer.
7. Updates fnic for removed lport emp pointer and above modified libfc APIs
fc_exch_recv, fc_exch_mgr_alloc and fc_exch_mgr_free.
8. Removes exch_get and exch_put from libfc_function_template as these
are no longer needed with EM anchor list and its match function use.
Also removes its default function fc_exch_get.
A defect this patch introduced regarding the libfc initialization order in
the fnic driver was fixed by Joe Eykholt <jeykholt@cisco.com>.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Currently there is a 1:1 relationship between the lport
and exchange manager. This macro takes an EM as an argument
and determines the lport from it. However, later patches
will use an EM list per lport, so we will no longer have
this 1:1 relationship- this macro must change.
The FC_EM_DBG macro is rarely used. There are four callers,
two can use FC_LPORT_DBG instead and two can be removed
since they're not necessary. This patch makes those changes
and removes the macro.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Adds EM list using a anchor struct fc_exch_mgr_anchor, anchor is used
to allow same EM instance sharing across more than one lport on a eth
device, this implementation is per discussed design posted at
http://www.open-fcoe.org/pipermail/devel/2009-June/002566.html.
The shared EM is required for multiple lports on eth device when
using multiple VLANs or NPIV.
Adds fc_exch_mgr_add API to add a EM to the lport and fc_exch_mgr_del
API to delete previously added EM.
Also adds function fc_exch_mgr_destroy() to destroy allocated EM.
The kref is added to the EM to keep track of EM usage count, the EM is
destroyed when no longer in use upon kref reaching to zero.
The caller can specify match function to fc_exch_mgr_add, this
will be used in determining exchange allocation from its EM or not.
Moved calling of fcoe_em_config below fcoe_libfc_config calling,
so that list head lp->ema_list is initialized before configuring
EM.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
State RPORT_ST_NONE was intented to be an invalid state (0), never used.
This was a misguided attempt to be sure it was always initialized.
Having an extra state meaning nothing requires switch statements to
have a case covering that state.
State NONE has been used instead to mean the remote port is being deleted.
Changing the name to RPORT_ST_DELETE.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The state NONE was meant to be invalid, but has been used as
the initial state. Rename it to be DISABLED, as more descriptive.
Further patches will make it the like the RESET state, except
it won't transition to FLOGI until fc_lport_fabric_login() is called.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
libfc debug messages currently show 'lport: <fc-id>:'
wher <fc-id> is the hex assigned port-id. When the lport
is logged off, that will be zero, so its hard to distinguish
which instance is involved. The FC-ID can change
if the port is re-patched or changes VSANs.
Two lports may even have the same FC-ID if connected to isolated SANs.
Change the debug messages to print the SCSI host number "hostN:",
which will not change for the life of the lport.
Still show the FC_ID on lport messages.
Also, add a macro to FC_RPORT_ID_DBG for rport debugging where there's
no rdata structure involved. It takes the lport and port_id as parameters.
Use this in fc_rport_recv_plogi_req() and fc_rport_recv_logo_req().
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This is unlikely to cause any problems, but the libfc debug macros
introduce extra undesirable semicolons.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Problem reported: http://marc.info/?l=dm-devel&m=124585978305866&w=2
scsi_dh does not do a refernce count for attach/detach, and this affects
the way it is supposed to work with multipath when a device is not
in the dev_list of the hardware handler.
This patch adds a reference count that counts each attach.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
If a SCSI ULD driver sets blk_queue_prep_rq(), it should clean it
up itself on remove(), and not from the bus callbacks. This
removes the need to hook into bus->remove(), which should not
be used at the same time as driver->remove().
[jejb: fix sdkp initialisation problem due to mismerge]
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch adds the /sys/module/libfc/parameters/debug_logging
file to sysfs as a module parameter. It accepts an integer
bitmask for logging. Currently it supports:
bit
LSB 0 = general libfc debugging
1 = lport debugging
2 = disc debugging
3 = rport debugging
4 = fcp debugging
5 = EM debugging
6 = exch/seq debugging
7 = scsi logging (mostly error handling)
the other bits are not used at this time.
The patch converts all of the libfc source files to use
these new macros and removes the old FC_DBG macro.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If we are sending or receiving data for the task successfully do
not run the scsi eh, because we know the task is making progress.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6:
[SCSI] aic79xx: make driver respect nvram for IU and QAS settings
[SCSI] don't attach ULD to Dell Universal Xport
[SCSI] lpfc 8.3.3 : Update driver version to 8.3.3
[SCSI] lpfc 8.3.3 : Add support for Target Reset handler entrypoint
[SCSI] lpfc 8.3.3 : Fix a couple of spin_lock and memory issues and a crash
[SCSI] lpfc 8.3.3 : FC/FCOE discovery fixes
[SCSI] lpfc 8.3.3 : Fix various SLI-3 vs SLI-4 differences
[SCSI] qla2xxx: Resolve a performance issue in interrupt
[SCSI] cnic, bnx2i: Fix build failure when CONFIG_PCI is not set.
[SCSI] nsp_cs: time_out reaches -1
[SCSI] qla2xxx: fix printk format warnings
[SCSI] ncr53c8xx: div reaches -1
[SCSI] compat: don't perform unneeded copy in sg_io code
[SCSI] zfcp: Update FC pass-through support
[SCSI] zfcp: Add FC pass-through support
[SCSI] FC Pass Thru support
This patch allows the Adaptec firmware to pass on its values for Packetize and
QAS. To do this, the settings max_iu and max_qas have been introduced into
the SPI transport class and populated from the adaptec NVram tables. Domain
validation in the SPI transport class will respect the max settings when
configuring to the highest possible speed for testing.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Attached is the ELS/CT pass-thru patch for the FC Transport. The patch
creates a generic framework that lays on top of bsg and the SGIO v4 ioctl
in order to pass transaction requests to LLDD's.
The interface supports the following operations:
On an fc_host basis:
Request login to the specified N_Port_ID, creating an fc_rport.
Request logout of the specified N_Port_ID, deleting an fc_rport
Send ELS request to specified N_Port_ID w/o requiring a login, and
wait for ELS response.
Send CT request to specified N_Port_ID and wait for CT response.
Login is required, but LLDD is allowed to manage login and decide
whether it stays in place after the request is satisfied.
Vendor-Unique request. Allows a LLDD-specific request to be passed
to the LLDD, and the passing of a response back to the application.
On an fc_rport basis:
Send ELS request to nport and wait for ELS response.
Send CT request to nport and wait for CT response.
The patch also exports several headers from include/scsi such that
they can be available to user-space applications:
include/scsi/scsi.h
include/scsi/scsi_netlink.h
include/scsi/scsi_netlink_fc.h
include/scsi/scsi_bsg_fc.h
For further information, refer to the last RFC:
http://marc.info/?l=linux-scsi&m=123436574018579&w=2
Note: Documentation is still spotty and will be added later.
[bharrosh@panasas.com: update for new block API]
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Conflicts:
drivers/message/fusion/mptsas.c
fixed up conflict between req->data_len accessors and mptsas driver updates.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* 'for-2.6.31' of git://git.kernel.dk/linux-2.6-block: (153 commits)
block: add request clone interface (v2)
floppy: fix hibernation
ramdisk: remove long-deprecated "ramdisk=" boot-time parameter
fs/bio.c: add missing __user annotation
block: prevent possible io_context->refcount overflow
Add serial number support for virtio_blk, V4a
block: Add missing bounce_pfn stacking and fix comments
Revert "block: Fix bounce limit setting in DM"
cciss: decode unit attention in SCSI error handling code
cciss: Remove no longer needed sendcmd reject processing code
cciss: change SCSI error handling routines to work with interrupts enabled.
cciss: separate error processing and command retrying code in sendcmd_withirq_core()
cciss: factor out fix target status processing code from sendcmd functions
cciss: simplify interface of sendcmd() and sendcmd_withirq()
cciss: factor out core of sendcmd_withirq() for use by SCSI error handling code
cciss: Use schedule_timeout_uninterruptible in SCSI error handling code
block: needs to set the residual length of a bidi request
Revert "block: implement blkdev_readpages"
block: Fix bounce limit setting in DM
Removed reference to non-existing file Documentation/PCI/PCI-DMA-mapping.txt
...
Manually fix conflicts with tracing updates in:
block/blk-sysfs.c
drivers/ide/ide-atapi.c
drivers/ide/ide-cd.c
drivers/ide/ide-floppy.c
drivers/ide/ide-tape.c
include/trace/events/block.h
kernel/trace/blktrace.c
This patch was inspired by Al Viro, for simplifying and fixing the
retrieval of osd-devices by in-kernel users, eg: file systems.
In-Kernel users, now, go through the same path user-mode does by
opening a file on the osd char-device and though holding a reference
to both the device and the Module.
A file pointer was added to the osd_dev structure which is now
allocated for each user. The internal osd_dev is no longer exposed
outside of the uld. I wanted to do that for a long time so each
libosd user can have his own defaults on the device.
The API is left the same, so user code need not change.
It is no longer needed to open/close a file handle on the osd
char-device from user-mode, before mounting an exofs on it.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
CC: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
libosd users that need to work with bios, must sometime use
the request_queue associated with the osd_dev. Make a wrapper for
that, and convert all in-tree users.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
For supporting of chained-bios we can not inspect the first
bio only, as before. Caller shall pass the total length of the
request, ie. sum_bytes(bio-chain).
Also since the bio might be a chain we don't set it's direction
on behalf of it's callers. The bio direction should be properly
set prior to this call. So fix a couple of write users that now
need to set the bio direction properly
[In this patch I change both library code and user sites at
exofs, to make it easy on integration. It should be submitted
via James's scsi-misc tree.]
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
CC: Jeff Garzik <jeff@garzik.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Martin K. Petersen