af9013 demod driver has i2c binding. Use it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Convert inttabs to format (reg, mask, val) which are suitable
parameters to pass directly for regmap_update_bits.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Pass correct device to dev_* logging functions, which allows us to
remove redundant KBUILD_MODNAME and __func__ parameters from log format.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Driver has calculated dvbv5 statistics, so use those as a base for
legacy dvbv3 statistics. Wrap and convert needed values to dvbv3,
remove old dvbv3 statistic implementations.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Implement dvbv5 signal strength estimate. We know tuner dependent
-80dBm and -50dBm agc values, construct line equation and use it to
map agc value to signal strength estimate.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Whilst rewritten largely, the basic logic remains same with one
exception: do not return immediately on success case. We are going to
add statistics that function and cannot return too early.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This mceusb does not need the carrier count quirk, with it set it reports
the carrier higher than it is.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Windows Media Center IR transceivers include two IR receivers;
wide-band/short-range and narrow-band/long-range. The short-range
(5cm distance) receiver is for IR learning and has IR carrier
frequency measuring ability.
Add mceusb driver support to select the short range IR receiver
and enable pass through of its IR carrier frequency measurements.
RC and LIRC already support these mceusb driver additions.
Test platform:
Linux raspberrypi 4.9.59-v7+ #1047 SMP Sun Oct 29 12:19:23 GMT 2017 armv7l GNU/Linux
mceusb 1-1.2:1.0: Registered Pinnacle Systems PCTV Remote USB with mce emulator interface version 1
mceusb 1-1.2:1.0: 2 tx ports (0x0 cabled) and 2 rx sensors (0x1 active)
Sony TV remote control
ir-ctl from v4l-utils
pi@raspberrypi:~ $ ir-ctl -V
IR raw version 1.12.3
pi@raspberrypi:~ $ ir-ctl -m -r
...
pulse 650
space 550
pulse 650
space 600
pulse 600
space 600
pulse 1200
space 600
pulse 650
space 550
pulse 650
space 600
pulse 600
space 600
pulse 550
carrier 40004
space 16777215
^C
pi@raspberrypi:~ $ exit
Signed-off-by: A Sun <as1033x@comcast.net>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A timeout of 200ms is much longer than necessary, and delays the decoding
decoding of a single scancode and the last scancode when a button is being
held. This makes the remote seem sluggish.
If the min_timeout and max_timeout values are set, the timeout is
configurable via the LIRC_SET_REC_TIMEOUT ioctl.
Tested-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Meson doesn't seem to be able to generate timeout events in hardware. So
install a software timer to generate the timeout events required by the
decoders to prevent "ghost keypresses".
Reported-by: Matthias Reichl <hias@horus.com>
Tested-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Drop bogus call to usb_driver_release_interface() from the disconnect()
callback. As the interface is already being unbound at this point,
usb_driver_release_interface() simply returns early.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ADV7604 has thirteen 256-byte maps that can be accessed via the main
I2C ports. Each map has it own I2C address and acts as a standard slave
device on the I2C bus.
Allow a device tree node to override the default addresses so that
address conflicts with other devices on the same bus may be resolved at
the board description level.
[Kieran: Re-adapted for mainline]
Signed-off-by: Jean-Michel Hautbois <jean-michel.hautbois@vodalys.com>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ADV748x has twelve 256-byte maps that can be accessed via the main
I2C ports. Each map has it own I2C address and acts as a standard slave
device on the I2C bus.
Allow a device tree node to override the default addresses so that
address conflicts with other devices on the same bus may be resolved at
the board description level.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ADV748x has 12 pages mapped onto I2C addresses.
In the existing implementation only 11 are mapped correctly in the page
enumerations, which causes an off-by-one fault on pages above the
infoframe definition due to a missing 'CBUS' page.
This causes the address for the CEC, SDP, TXA, and TXB to be incorrectly
programmed during the iterations in adv748x_initialise_clients().
Until now this has gone un-noticed due to the fact that following the
creation of the clients - the device is reset and the addresses are
reprogrammed in manually by the call to "adv748x_write_regs(state,
adv748x_set_slave_address);"
As part of moving to dynamic i2c address allocations repair this by
providing the missing CBUS page definition.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ADV748x has identical map configurations for each register map. The
duplication of each map can be simplified using a helper macro such that
each map is represented on a single line.
Define ADV748X_REGMAP_CONF for this purpose use it to create the tables.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The v4l2_subdev core s_power op was used for two different things: power on/off
sensors or video decoders/encoders and to put a tuner in standby (and only the
tuner!). There is no 'tuner wakeup' op, that's done automatically when the tuner
is accessed.
The danger with calling (s_power, 0) to put a tuner into standby is that it is
usually broadcast for all subdevs. So a video receiver subdev that supports
s_power will also be powered off, and since there is no corresponding (s_power, 1)
they will never be powered on again.
In addition, this is specifically meant for tuners only since they draw the most
current.
This patch adds a new tuner op called 'standby' and replaces all calls to
(core, s_power, 0) by (tuner, standby). This prevents confusion between the two
uses of s_power. Note that there is no overlap: bridge drivers either just want
to put the tuner into standby, or they deal with powering on/off sensors. Never
both.
This also makes it easier to replace s_power for the remaining bridge drivers
with some PM code later.
Whether we want something cleaner for tuners in the future is a separate topic.
There is a lot of legacy code surrounding tuners, and I am very hesitant about
making changes there.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fixed si470x_start() disabling the interrupt signal, causing tune
operations to never complete. This does not affect USB radios
because they poll the registers instead of using the IRQ line.
Signed-off-by: Douglas Fischer <fischerdouglasc@gmail.com>
[hans.verkuil@cisco.com: fixed 80 column checkpatch warning]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Added the call to v4l2_device_register() required to add a new radio device.
Without this patch, it is impossible for the driver to load. This does not
affect USB devices.
Signed-off-by: Douglas Fischer <fischerdouglasc@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fixed si470x_set_channel() trying to tune before chip is turned
on, which causes warnings in dmesg and when probing, makes driver
wait for 3s for tuning timeout. This issue did not affect USB
devices because they have a different probing sequence.
Signed-off-by: Douglas Fischer <fischerdouglasc@gmail.com>
[hans.verkuil@cisco.com: fixed space-after-( checkpatch warning]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Do not stop/restart dma on overrun or errors.
Dma will be restarted on current frame transfer
completion. Frame transfer completion is ensured
even if overrun or error occurs by DCMI continuous
capture mode which restarts data transfer at next
frame sync.
Do no warn on overrun while in irq thread, this slows down
system and lead to more overrun errors. Use a counter
instead and log errors at stop streaming.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
v4l2_find_nearest_format is not useful for drivers in finding the best
matching format as it assumes a V4L2 specific struct. Drivers will use
v4l2_find_nearest_size instead.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use v4l2_find_nearest_size instead of a driver specific function to find
nearest matching size.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use v4l2_find_nearest_size instead of a driver specific function to find
nearest matching size.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use v4l2_find_nearest_size instead of a driver specific function to find
nearest matching size.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add a function (as well as a helper macro) to obtain the best size in a
list of device specific sizes. This helps writing drivers as well as
aligns interface behaviour across drivers.
The struct in which this information is contained in is typically specific
to the driver, therefore the existing function v4l2_find_nearest_format()
does not address the need.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This renames the protocol for the imon rc driver from other to imon,
since it is now an known protocol. Although different name will show up
in the sysfs protocol file, loading a keymap using existing ir-keytable
versions still works.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This makes it possible to use the various iMON remotes with any raw IR
RC device.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If there is IR in the raw kfifo when ir_raw_event_unregister() is called,
then kthread_stop() causes ir_raw_event_thread to be scheduled, decode
some scancodes and re-arm timer_keyup. The timer_keyup then fires when
the rc device is long gone.
Cc: stable@vger.kernel.org
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These devices were supported by the lirc_imon.c driver which was removed
from staging in commit f41003a23a ("[media] staging: lirc_imon: port
remaining usb ids to imon and remove").
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Note that the stick on the remote is not supported yet.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This code was ported without the necessary hardware to test. There
are multiple problems which are more easily solved by writing a
separate driver.
This reverts commit f41003a23a.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch updates the sunxi-ir driver to set the base clock frequency from
devicetree.
This is necessary since there are different ir receivers on the
market, that operate with different frequencies. So this value could be
set if the attached ir receiver needs a different base clock frequency,
than the default 8 MHz.
Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The old wait_on_atomic_t() is going to get removed, use the more
flexible wait_var_event() API instead.
Unlike wake_up_atomic_t(), wake_up_var() will issue the wakeup
even if the variable is not 0.
No change in functionality.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
There is a double sizeof() typo here so we don't duplicate the struct
properly.
Fixes: be7fd3c3a8 ("media: em28xx: Hauppauge DualHD second tuner functionality")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Like in ddbridge, get rid of all duplicated I2C client handling constructs
and rather make use of the newly added dvb_module_*() helpers. Makes
things more clean and removes the (cosmetic) need for some variables.
The check on a valid ptr on ci->en isn't really needed since the cxd2099
driver will set it at a time where it is going to return successfully
from probing.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Instead of keeping duplicated I2C client handling construct, make use of
the newly introduced dvb_module_*() helpers. This not only keeps things
way cleaner and removes the need for duplicated I2C client attach code,
but even allows to get rid of some variables that won't help in making
things look cleaner anymore.
The check on a valid ptr on port->en isn't really needed since the cxd2099
driver will set it at a time where it is going to return successfully
from probing.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The CIMaX SP2 driver is a EN50221 CI controller I2C driver similar to the
cxd2099 driver. Move it's Kconfig block into the newly introduced CI
subsection.
Cc: Olli Salonen <olli.salonen@iki.fi>
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The cxd2099 driver makes use of the Regmap I2C kernel API, thus add
"select REGMAP_I2C" to it's Kconfig block. Also, make it default "m" if
!MEDIA_SUBDRV_AUTOSELECT, just like every other dvb-frontend driver.
And, while at it, remove the hyphens around the help tag.
Cc: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If I2C is present and it is module, the DVB core should also
be a module, otherwise build will now fail with:
drivers/media/dvb-core/dvbdev.o: In function `dvb_module_probe':
drivers/media/dvb-core/dvbdev.c:965: undefined reference to `i2c_new_device'
drivers/media/dvb-core/dvbdev.c:972: undefined reference to `i2c_unregister_device'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There's a comment there at s82168 that it is wrong.
With firmware 4.0.11, sleep/resume works well without
need of download it every time. But firmware 4.0.19
needs to be downloaded again after sleep.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These patches remove the metag architecture and tightly dependent
drivers from the kernel. With the 4.16 kernel the ancient gcc 4.2.4
based metag toolchain we have been using is hitting compiler bugs, so
now seems a good time to drop it altogether.
-----BEGIN PGP SIGNATURE-----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=zDIl
-----END PGP SIGNATURE-----
Merge tag 'metag_remove_2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jhogan/metag into asm-generic
Remove metag architecture
These patches remove the metag architecture and tightly dependent
drivers from the kernel. With the 4.16 kernel the ancient gcc 4.2.4
based metag toolchain we have been using is hitting compiler bugs, so
now seems a good time to drop it altogether.
* tag 'metag_remove_2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jhogan/metag:
i2c: img-scb: Drop METAG dependency
media: img-ir: Drop METAG dependency
watchdog: imgpdc: Drop METAG dependency
MAINTAINERS/CREDITS: Drop METAG ARCHITECTURE
tty: Remove metag DA TTY and console driver
clocksource: Remove metag generic timer driver
irqchip: Remove metag irqchip drivers
Drop a bunch of metag references
docs: Remove remaining references to metag
docs: Remove metag docs
metag: Remove arch/metag/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
As warned by smatch:
drivers/media/i2c/s5c73m3/s5c73m3-core.c:268 s5c73m3_check_status() error: uninitialized symbol 'status'.
if s5c73m3_check_status() is called too late, time_is_after_jiffies(end)
will return 0, causing the while to abort before reading status.
The current code will do the wrong thing here, as it will still
check if status != value. The right fix here is to change
the logic to ensure that it will always read the status.
Suggested-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
drivers/media/dvb-frontends/cxd2880/cxd2880_top.c: In function ‘cxd2880_set_ber_per_period_t’:
drivers/media/dvb-frontends/cxd2880/cxd2880_top.c:677:34: warning: variable ‘c’ set but not used [-Wunused-but-set-variable]
struct dtv_frontend_properties *c;
^
drivers/media/dvb-frontends/cxd2880/cxd2880_top.c: In function ‘cxd2880_set_ber_per_period_t2’:
drivers/media/dvb-frontends/cxd2880/cxd2880_top.c:790:34: warning: variable ‘c’ set but not used [-Wunused-but-set-variable]
struct dtv_frontend_properties *c;
^
drivers/media/dvb-frontends/cxd2880/cxd2880_top.c: In function ‘cxd2880_get_frontend’:
drivers/media/dvb-frontends/cxd2880/cxd2880_top.c:1799:23: warning: variable ‘priv’ set but not used [-Wunused-but-set-variable]
struct cxd2880_priv *priv = NULL;
^~~~
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
It is not needed anymore to include the dvb-core directory,
as all the public headers that used to be there was moved
to include/media.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is the Makefile, Kconfig files of driver
and MAINTAINERS file update about the driver
for the Sony CXD2880 DVB-T2/T tuner + demodulator.
Signed-off-by: Yasunari Takiguchi <Yasunari.Takiguchi@sony.com>
Signed-off-by: Masayuki Yamamoto <Masayuki.Yamamoto@sony.com>
Signed-off-by: Hideki Nozawa <Hideki.Nozawa@sony.com>
Signed-off-by: Kota Yonezawa <Kota.Yonezawa@sony.com>
Signed-off-by: Toshihiko Matsumoto <Toshihiko.Matsumoto@sony.com>
Signed-off-by: Satoshi Watanabe <Satoshi.C.Watanabe@sony.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These functions monitor the driver and watch for task completion.
This is part of the Sony CXD2880 DVB-T2/T tuner + demodulator driver.
Signed-off-by: Yasunari Takiguchi <Yasunari.Takiguchi@sony.com>
Signed-off-by: Masayuki Yamamoto <Masayuki.Yamamoto@sony.com>
Signed-off-by: Hideki Nozawa <Hideki.Nozawa@sony.com>
Signed-off-by: Kota Yonezawa <Kota.Yonezawa@sony.com>
Signed-off-by: Toshihiko Matsumoto <Toshihiko.Matsumoto@sony.com>
Signed-off-by: Satoshi Watanabe <Satoshi.C.Watanabe@sony.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This part of the driver has the main routines to handle
the tuner and demodulator functionality. The tnrdmd_mon.* files
have monitor functions for the driver.
This is part of the Sony CXD2880 DVB-T2/T tuner + demodulator driver.
Signed-off-by: Yasunari Takiguchi <Yasunari.Takiguchi@sony.com>
Signed-off-by: Masayuki Yamamoto <Masayuki.Yamamoto@sony.com>
Signed-off-by: Hideki Nozawa <Hideki.Nozawa@sony.com>
Signed-off-by: Kota Yonezawa <Kota.Yonezawa@sony.com>
Signed-off-by: Toshihiko Matsumoto <Toshihiko.Matsumoto@sony.com>
Signed-off-by: Satoshi Watanabe <Satoshi.C.Watanabe@sony.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These are common files for the driver for the
Sony CXD2880 DVB-T2/T tuner + demodulator.
These contains helper functions for the driver.
Signed-off-by: Yasunari Takiguchi <Yasunari.Takiguchi@sony.com>
Signed-off-by: Masayuki Yamamoto <Masayuki.Yamamoto@sony.com>
Signed-off-by: Hideki Nozawa <Hideki.Nozawa@sony.com>
Signed-off-by: Kota Yonezawa <Kota.Yonezawa@sony.com>
Signed-off-by: Toshihiko Matsumoto <Toshihiko.Matsumoto@sony.com>
Signed-off-by: Satoshi Watanabe <Satoshi.C.Watanabe@sony.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is the SPI adapter part of the driver for the
Sony CXD2880 DVB-T2/T tuner + demodulator.
Signed-off-by: Yasunari Takiguchi <Yasunari.Takiguchi@sony.com>
Signed-off-by: Masayuki Yamamoto <Masayuki.Yamamoto@sony.com>
Signed-off-by: Hideki Nozawa <Hideki.Nozawa@sony.com>
Signed-off-by: Kota Yonezawa <Kota.Yonezawa@sony.com>
Signed-off-by: Toshihiko Matsumoto <Toshihiko.Matsumoto@sony.com>
Signed-off-by: Satoshi Watanabe <Satoshi.C.Watanabe@sony.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Not sure why, but, on ia64, with Linaro's gcc 7.3 compiler,
using #ifdef (CONFIG_I2C) is not OK.
So, replace it by IS_ENABLED(CONFIG_I2C), in order to fix the
builds there.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Hauppauge produced a revision of ImpactVCBe using an 888,
with a 25MHz crystal, instead of using the default third
overtone 50Mhz crystal. This overrides that frequency so
that the cx25840 is properly configured. Without the proper
crystal setup the cx25840 cannot load the firmware or
decode video.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Currently clk_freq is ignored entirely, because the cx235840 driver
configures the xtal at the chip defaults. This is an issue if a
board is produced with a non-default frequency crystal. If clk_freq
is not zero the cx25840 will attempt to use the setting provided,
or fall back to defaults otherwise.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Proper cx2388x chip type is detected in cx25840 probe, the clock
rate is untouched however in probe. The cx25840 only checks for
non default clock values for 888 and provides custom settings for
25MHz 888. This change ensures that cx23888 chips with default 50MHz
crystals will not get configured as if they have 25MHz crystals. A
cx23887 board will continue to be configured for 25MHz crystal as
there is no custom clock support included for it.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The cx25840 driver currently configures 885, 887, and 888 using
default divisors for each chip. This check to see if the cx23885
driver has passed the cx25840 a non-default clock rate for a
specific chip. If a cx23885 board has left clk_freq at 0, the
clock default values will be used to configure the PLLs.
This patch only has effect on 888 boards who set clk_freq to 25M.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The GPIO settings for quadHD boards are wrong. Fix them.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Hauppauge HVR-975 is a hybrid, dual frontend, single tuner USB device.
It contains lgdt3306a and si2168 frontends and one si2157 tuner. The
lgdt3306a frontend is currently enabled. This creates the second
demodulator and attaches it to the tuner.
Enables lgdt3306a|si2168 + si2157
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If frontend[1] exists, then enable the dvb adapter mfe lock system.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Utilize the i2c mux adapter returned by the frontend.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This symbol mismatch is handled by NULL'ing out the release
callback if the driver is loaded as an i2c device.
This patch reverts:
- commit 94448e21cf ("media: lgdt3306a: Fix a double kfree on i2c
device remove")
- commit 835d66173a ("media: lgdt3306a: Fix module count mismatch
on usb unplug")
The symbol count mismatch is handled by:
- commit 5b3a8e9069 ("media: lgdt3306a: Set fe ops.release to
NULL if probed")
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A possible hardware bug was discovered when using CA addon hardware
attached to the ngene hardware, in that the TS input buffer much likely
will shift and thus become unaligned to 188 byte blocks (a full TS frame)
when things like CA module initialisation (which happens via differing
communication paths) take place. This causes the TS NULL removal in
tsin_exchange() to fail to detect this previously inserted data and thus
causes userspace applications to receive data they didn't sent beforehand
and ultimately cause troubles.
On driver load with an inserted CAM, buffers are fine at first (note that
the driver has to keep the communication running from/to the card by
inserting TS NULL frames, this is done in tsout_exchange() via
FillTSBuffer() - that data is simply sent back by the hardware):
offset | 0 1 2 3 4 5 .... 188 189 190 191 192 193 .... 376
data | 47 1f ff 10 6f 6f .... 47 1f ff 10 6f 6f .... 47
After a few seconds, the CA module is recognised and initialised, which is
signalled by
dvb_ca_en50221: dvb_ca adapter X: DVB CAM detected and initialised successfully
This is where the first shift happens (this is always four bytes), buffer
becomes like this:
offset | 0 1 2 3 4 5 .... 188 189 190 191 192 193 .... 376
data | 6f 6f 6f 6f 47 1f .... 6f 6f 6f 6f 47 1f .... 6f
Next, VDR, TVHeadend or any other CI aware application is started, buffers
will shift by even more bytes. It is believed this is due to the hardware
not handling control and data bytes properly distinct, and control data
having an influence on the actual data stream, which we cannot properly
detect at the driver level.
Workaround this hardware quirk by adding a detection for the TS sync byte
0x47 before each TS frame copy, scan for a new SYNC byte and a TS NULL
packet if buffers become unaligned, take note of that offset and apply
that when copying data to the DVB ring buffers. The last <188 bytes from
the hardware buffers are stored in a temp buffer (tsin_buffer), for which
the remainder will be in the beginning of the next hardware buffer (next
iteration of tsin_exchange()). That remainder will be appended to the
temp buffer and finally sent to the DVB ring buffer. The resulting TS
stream is perfectly fine, and the TS NULL packets inserted by the driver
which are sent back are properly removed. The resulting offset is being
clamped to 188 byte segments (one TS packet). Though this can result in
a repeated TS packet if the overall offset grows beyond this (and it
will grow only on CA initialisation), this is still way better than
unaligned TS frames and data sent to userspace that just isn't supposed
to be there.
This compensation can be toggled by the ci_tsfix modparam, which defaults
to 1 (enabled). In the case of problems, this can be turned off by setting
the parameter to 0 to restore the old behaviour.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Move the copy logic that will skip previously inserted TS NULL frames when
moving data to the DVB ring buffers into an own function. This is done to
not duplicate code all over the place with the following TS offset shift
fixup patch.
While we're touching this part of the code, get rid of the DEBUG_CI_XFER
debug-ifdeffery. This could be toggleable either by a Kconfig or a module
param, but in the end this will accidentally be enabled and cause lots
of kernel log messages, and such devel debug shouldn't be there anyway.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
On some architectures such as arm64, siano chip based TV-tuner
USB devices are not recognized correctly due to coherent memory
allocation failure with the following error:
[ 663.556135] usbcore: deregistering interface driver smsusb
[ 683.624809] smsusb:smsusb_probe: board id=18, interface number 0
[ 683.633530] smsusb:smsusb_init_device: smscore_register_device(...) failed, rc -12
[ 683.641501] smsusb:smsusb_probe: Device initialized with return code -12
[ 683.652978] smsusb: probe of 1-1:1.0 failed with error -12
This is caused by dma_alloc_coherent(NULL, ...) returning NULL in
smscoreapi.c.
To fix this error, allocate the buffer memory for the USB devices
via kmalloc() and let the USB core do the DMA mapping and free.
Signed-off-by: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ">" should be ">=" so that we don't read one element beyond the end
of the array.
Fixes: 8a77009be4 ("media: ov5695: add support for OV5695 sensor")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Update the register 0x3503 to use 'no delay latch' for gain.
This makes sensor to output the first frame as normal rather
than a very dark one.
Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The PM runtime operations are unused when CONFIG_PM is disabled,
leading to a harmless warning:
drivers/media/platform/renesas-ceu.c:1003:12: error: 'ceu_runtime_suspend' defined but not used [-Werror=unused-function]
static int ceu_runtime_suspend(struct device *dev)
^~~~~~~~~~~~~~~~~~~
drivers/media/platform/renesas-ceu.c:987:12: error: 'ceu_runtime_resume' defined but not used [-Werror=unused-function]
static int ceu_runtime_resume(struct device *dev)
^~~~~~~~~~~~~~~~~~
This adds a __maybe_unused annotation to shut up the warning.
Fixes: 32e5a70dc8 ("media: platform: Add Renesas CEU driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The CSTRST_CPON mask was wrongly assigned to BIT(1) instead of BIT(0).
Fix that by changing the mask opportunely.
Reported-by: Dylan Laduranty <dylan.laduranty@mesotic.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As all drivers using the cxd2099 are converted to handle attach/detach
the generic I2C client way, the static inline cxd2099_attach isn't
required anymore. Thus cleanup cxd2099.h from the remainders, the adr
struct member also isn't used anymore.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Report I2C_FUNC_I2C in .functionality() as well. The I2C interface can
handle this fine and even is required for all I2C client drivers that
utilise the regmap API which are used from within the ngene driver.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Change the way the cxd2099 hardware is being attached to the new I2C
client interface way.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As the media subdevice is registered with 'v4l2_async_register_subdev()'
unregister it at module removal time with
'v4l2_async_unregister_subdev()'
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
msleep() can sleep up to 20ms.
As suggested by Documentation/timers/timers_howto.txt replace it with
usleep_range() with up to 5ms delay.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add an empty line before return at the end of functions.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A lot of comments that would fit a single line were spread on two or
more lines. Also fix capitalization and punctuation where appropriate.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Align all function parameters to first open brace when declaring
functions.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
msleep() can sleep up to 20ms.
As suggested by Documentation/timers/timers_howto.txt replace it with
usleep_range() with up to 5ms delay.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Two minor style fixes, align function parameter and remove un-necessary
spaces.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Yet more whitespace and style neatening
o Add blank lines before returns
o Reverse a logic test and return early on error
o Move formats to same line as dev_<level> calls
o Remove an unnecessary period from a logging message
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Update multiline statements to open parenthesis.
Update a ?: to a single line.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A lot of comments that would fit a single line were spread on two or
more lines. Also fix capitalization and punctuation where appropriate.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Implement the poll callback for the dvbdev_ci file ops. The ts_poll()
function queries the DVB ring buffers for available data and space, and
reports this as appropriate. Also, set the dvb_device readers, writers
and users to proper values (one reader, one writer, two users).
This fixes the raw CI TS transport in conjunction with TVheadend's
DDCI functionality.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When probing the I2C busses in cineS2_probe(), it's no error when there's
no hardware connected to the probed expansion connector, so print this
informal message with info severity.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Currently, if there's no CXD2099AR attached to any expansion connector of
the ngene hardware, it will complain with this on every module load:
cxd2099 1-0040: No CXD2099AR detected at 0x40
cxd2099: probe of 1-0040 failed with error -5
ngene 0000:02:00.0: CXD2099AR attach failed
This happens due to the logic assuming such hardware is always there and
blindly tries to attach the cxd2099 I2C driver. Rather add a probe
function (in ngene-cards.c with a prototype in ngene.h) to check for
the existence of such hardware before probing, and don't try further if
no CXD2099 was found.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The I2C adapter evaluation (based on chan->number) is duplicated at
several places (tuner_attach_() functions, demod_attach_stv0900() and
cineS2_probe()). Clean this up by wrapping that construct in a separate
function which all users of that can pass the ngene_channel pointer and
get the correct I2C adapter from.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support for the STV0910/STV6111/LNBH25 based DuoFlex S2 V4 DVB-S2
addon modules by recognizing them from their XO2 type value and using
the auxiliary stv0910, stv6111 and lnbh25 driver to form a complete
DVB frontend.
This also adds autoselection (if MEDIA_SUBDRV_AUTOSELECT) of the STV0910,
STV6111 and LNBH25 demod/tuner/LNB-IC drivers to Kconfig.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Recognize (probe) and support (attach) all Sony CXD28xx based DuoFlex
addon modules/cards, namely the DuoFlex CT2 (CXD2837), ISDB-T (CXD2838),
C2T2 (CXD2843) and C2T2I (CXD2854). Since all these modules are equipped
with a MachXO2 interface, that support is required for the hardware to
work. This functionality utilises the auxiliary cxd2841er and tda18212
drivers.
This also adds autoselection (if MEDIA_SUBDRV_AUTOSELECT) of the CXD2841ER
demod driver to Kconfig. The __maybe_unused annotation can now be removed
from the xo2names array.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Detect and initialise modules equipped with XO2 interfaces (Lattice
MachXO2). This requires a few more I2C transfer functions which this adds
as well. Defines for the different possible (available) module types are
added to ngene.h. The support for the actual tuners contained on these
addon modules is kept separate from this commit and is being added with
the next commits.
The xo2names array is temporarily marked __maybe_unused to silence a
corresponding compiler warning at this stage.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support for STV0367+TDA18212 based DuoFlex CT addon modules. For this,
add a demod probe function and all necessary demod/tuner attach functions
which use existing auxiliary drivers (stv0367 and tda18212) to support
this hardware. As tda18212 is an I2C client driver, proper cleanup code
is added to the deregistration sequence in ngene-core. To not cause use-
after-free situations when there's a CXD2099 I2C client connected, which
is rather freed in ngene-core.c:cxd_detach(), add i2c_client_fe to struct
ngene_channel to keep track if the i2c_client was allocated by a frontend
driver, rather than the CI code paths. Also move the I2C access functions
to the top of the file and add the required read_regs() function for the
tda18212 ping to work.
This adds autoselection (if MEDIA_SUBDRV_AUTOSELECT) of the STV0367 demod
driver and TDA18212 tuner driver to Kconfig aswell.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make it more clear which demod_type is used for which hardware by having
defines for the possible demod_type values. With that, change the
demod_type evaluation in tuner_attach_probe() to a switch-case instead
of an if() for each possible value.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Convert all printk() and pr_*() kernel log printing to rather use the
dev_*() macros. Not only is it discouraged to use printk() (checkpatch
even complains about that), but also this helps identifying the exact PCI
device for any printed event, and it makes almost all printing shorter
in terms of code style since there's no need to use KERN_* DEVICE_NAME
any more (dev_*() will take care of this).
Since the dprintk macro define isn't used anymore, remove it.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add two more device IDs for cards supported by the ngene driver.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A successful CA module initialisation isn't an error. Change the
log print to info severity accordingly.
Cc: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some local variables will be set to an appropriate value before usage.
Thus omit explicit initialisations at the beginning of these functions.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Move the ts bus control function moved higher, enabling it
after configuring frontend and removeing ts_bus_ctrl callback.
While here, also add an error checking and re-add a comment
that were removed by commit 445877742c ("media: si2168:
Add ts bus coontrol, turn off bus on sleep").
[mchehab@s-opensource.com: I ended by applying the first version,
instead of the right one. So, this patch contains the diff and
the v2 changelog instead]
Fixes: 445877742c ("media: si2168: Add ts bus coontrol, turn off bus on sleep")
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Rework both DiSEqC send functions (send_master_cmd() and send_burst()) to
utilise the new SET_REG() and SET_FIELD() macros. Esp. due to SET_FIELD(),
this makes sure that not all bits (with unrelated purposes) are always
rewritten, but only those needed for sending DiSEqC commands. In
send_burst(), this makes sure that DISEQC_MODE isn't changed from 3 to 2
inbetween when sending SEC_MINI_A. Also, change both functions to write
DISEQC_MODE first before setting DIS_PRECHARGE. This makes diseqc control
work more reliable for "fullblown" DiSEqC strings in VDR's diseqc.conf in
combination with certain multiswitches.
Fixes: 448461af0e ("media: dvb-frontends/stv0910: implement diseqc_send_burst")
Reported-by: Helmut Auer <post@helmutauer.de>
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Helmut Auer <post@helmutauer.de>
Tested-by: Richard Scobie <rascobie@slingshot.co.nz>
Tested-by: Dietmar Spingler <d_spingler@freenet.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
According to the TODO file, this driver only landed in staging because of
the way device nodes and data transfers are handled. Besides that this way
(use of secX devices) has become sort of standard to date (ie. VDR
supports this literally since ages via the ddci plugin, TVHeadend received
this functionality lately, and minisatip being currently worked on
regarding this), most importantly this I2C client only driver isn't even
responsible for setting up device nodes, not for handling data
transfer and so on, but only serves as interface for the dvb_ca_en50221
subsystem, just like every other DVB card out in the wild, with hard-wired
or such flexible CA interfaces. And, it would even work with cards having
the cxd2099 controller hard-wired.
Also, this driver received quite some love and even is a proper I2C client
driver by now. So, as this driver acts as a EN50221 frontend device, move
it to dvb-frontends. There is no need to keep it buried in staging.
This commit also updates all affected Kconfig and Makefile's, and adds
MEDIA_AUTOSELECT depends to ddbridge and ngene.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Change the way the cxd2099 hardware is being attached to the new I2C
client interface way.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Deduplicate the checks for a valid ptr in port->en, and also handle the
default case to also catch eventually yet unsupported CI hardware.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Due to a typo, the mask was destroyed by a comparison instead of a bit
shift.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The PLAT_S5P symbol was removed in commit d78c16ccde ("ARM: SAMSUNG:
Remove remaining legacy code").
Remove the PLAT_S5P dependency from VIDEO_SAMSUNG_S5P_CEC.
Discovered with the
https://github.com/ulfalizer/Kconfiglib/blob/master/examples/list_undefined.py
script.
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Thoses files are unused since commit b3b961448f ("V4L/DVB (13795): [Mantis/Hopper] Code overhaul, add Hopper devices into the PCI ID list")
8 year after, we could remove it.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
bsp_i2c.h is unused since commit ffe7c4f921 ("[media] drx-j: Get rid of drx39xyj/bsp_tuner.h")
Remove it from tree.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Instead of directly accessing to dmadev->device_prep_interleaved_dma() use
the dmaengine_prep_interleaved_dma() wrapper instead.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Hauppauge Solo/Dual HD DVB models use a si2157 tuner, which is set to
produce inverted spectrum. This configures the si2168 DVB demod for
inverted spectrum on both affected models.
[mchehab@s-opensource.com: rebased on the top of upstream]
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some tuners produce inverted spectrum, but the si2168 is not
currently set up to accept it. This adds an optional parameter
to set the frontend up to receive inverted spectrum.
Parameter is optional and only boards who enable inversion
will utilize this.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
While experimenting with older compiler versions, I ran
into a warning that no longer shows up on gcc-4.8 or newer:
drivers/media/platform/s3c-camif/camif-capture.c: In function '__camif_subdev_try_format':
drivers/media/platform/s3c-camif/camif-capture.c:1265:25: error: array subscript is below array bounds
This is an off-by-one bug, leading to an access before the start of the
array, while newer compilers silently assume this undefined behavior
cannot happen and leave the loop at index 0 if no other entry matches.
As Sylvester explains, we actually need to ensure that the
value is within the range, so this reworks the loop to be
easier to parse correctly, and an additional check to fall
back on the first format value for any unexpected input.
I found an existing gcc bug for it and added a reduced version
of the function there.
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=69249#c3
Fixes: babde1c243 ("[media] V4L: Add driver for S3C24XX/S3C64XX SoC series camera interface")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The driver outputs on success, but is silent on failure. Give
one message that probe failed.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The driver is near silent, this adds a simple announcement at the
end of probe after the chip has been detected and upgrades a debug
message to error if probe has failed.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Includes a function to set TS MODE property os si2168. The function
either disables the TS output bus, or sets mode to config option.
When going to sleep the TS bus is turned off, this makes the driver
compatible with multiple frontend usage.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Include ability to add a i2c device style frontend to cx231xx USB
bridge. All current boards set to use frontend[0]. Changes are
backwards compatible with current behaviour.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Include ability to add a second dvb attach style frontend to cx231xx
USB bridge. All current boards set to use frontend[0]. Changes are
backwards compatible with current behaviour.
[mchehab@s-opensource.com: fix some coding style issues]
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Commit f8585ce655 ("[media] dvb-usb-cxusb: Geniatech T230C support")
sneaked in an unrelated change for the older T230 (not C) model.
As the commit was reverted this change was reverted too,
although likely correct.
Fixes: f8585ce655 ("[media] dvb-usb-cxusb: Geniatech T230C support")
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This reverts commit f8585ce655.
The T230C is handled by the dvb-usb-v2/dvbsky.c driver, which should
be preferred over a dvb-usb (v1) driver.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Hauppauge HVR-975 is hybrid NTSC/PAL, QAM/ATSC, and DVB-C/T/T2 usb device.
Only ATSC/QAM front end is initially active. Second frontend support is
work in progress.
CX23102 + LG3306A/Si2168(WiP) + Si2157
Changes since v1:
- removed double semicolon
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
gcc-8 reports
drivers/media/dvb-frontends/dibx000_common.c: In function
'i2c_adapter_init':
./include/linux/string.h:245:9: warning: '__builtin_strncpy' specified
bound 48 equals destination size [-Wstringop-truncation]
We need to use strlcpy() to make sure the dest string is
nul-terminated.
Signed-off-by: Xiongfeng Wang <xiongfeng.wang@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Don't populate the const read-only array 'cmd' on the stack but instead
make it static. Makes the object code smaller by 38 bytes:
Before:
text data bss dec hex filename
4950 868 0 5818 16ba fimc-is-regs.o
After:
text data bss dec hex filename
4824 956 0 5780 1694 fimc-is-regs.o
(gcc version 7.2.0 x86_64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add new QuadHD digital only PCIe boards to driver list.
Differentiate them from 888 digital/analog QuadHD models.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add new PCIe DVB-S/S2.
A single port Hauppauge HVR-5525
cx23885 + a8293 + m88rs6000t
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add ID of new card revision to driver list
Analog PAL/NTSC capture.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are a number of coding style issues at em28xx-video.
Fix most of them, by using checkpatch in strict mode to point
for it.
Automatic fixes were made with --fix-inplace, but those
were complemented by manual work.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are a number of coding style issues at em28xx-input.
Fix most of them, by using checkpatch in strict mode to point
for it.
Automatic fixes were made with --fix-inplace, but those
were complemented by manual work.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are a number of coding style issues at em28xx-i2c.
Fix most of them, by using checkpatch in strict mode to point
for it.
Automatic fixes were made with --fix-inplace, but those
were complemented by manual work.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are a number of coding style issues at em28xx-core.
Fix most of them, by using checkpatch in strict mode to point
for it.
Automatic fixes were made with --fix-inplace, but those
were complemented by manual work.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There is a complex loop there with identifies the em28xx
endpoints. It has lots of identations inside, and big names,
making harder to understand.
Simplify it by moving the main logic into a static function.
While here, rename "interface" var to "intf".
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are a number of coding style issues, pointed by checkpatch
on strict mode.
Fix the ones that don't require code refactor here.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are some coding style issues at em28xx-camera.
Fix them, by using checkpatch in strict mode to point for it.
Automatic fixes with --fix-inplace were complemented by manual
work.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are a number of coding style issues at em28xx-audio.
Fix them, by using checkpatch in strict mode to point for it.
Automatic fixes with --fix-inplace were complemented by manual
work.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use BIT() macros and fix one comment that is not following
the Kernel coding style.
It should be noticed that the registers bit masks should be
casted to unsigned char, as, otherwise, it would produce
warnings like:
drivers/media/usb/em28xx/em28xx-cards.c:81:33: warning: large integer implicitly truncated to unsigned type [-Woverflow]
{EM2820_R08_GPIO_CTRL, 0x6d, ~EM_GPIO_4, 10},
^
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There used to have a lot of coding style issues there. The
ones detected by checkpatch, in strict mode, got fixed.
Still, we need to work more on it, in order to document all
struct fields using kernel-doc macros, but this will be done
on some future patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Antti Palosaari