Sometimes, it's necessary to enable software's ability to quiesce and
reset endpoint hardware with function-level granularity, so provide
support for it.
The patch implement Function Level Reset(FLR) feature following PCI-e
spec. And this is the first step. We would add more generic method, like
D0/D3, to allow more devices support this function.
The patch contains two functions. pcie_reset_function() is the new
driver API, and, contains some action to quiesce a device. The other
function is a helper: pcie_execute_reset_function() just executes the
reset for a particular device function.
Current the usage model is in KVM. Function reset is necessary for
assigning device to a guest, or moving it between partitions.
For Function Level Reset(FLR), please refer to PCI Express spec chapter
6.6.2.
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch adds support for PCI Express Alternative Routing-ID
Interpretation (ARI) capability.
The ARI capability extends the Function Number field of the PCI Express
Endpoint by reusing the Device Number which is otherwise hardwired to 0.
With ARI, an Endpoint can have up to 256 functions.
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Disable ASPM on pre-1.1 PCIe devices, as many of them don't implement it
correctly.
Tested-by: Jack Howarth <howarth@bromo.msbb.uc.edu>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If the offset of PCI device's PM capability in its configuration space,
the mask of states that the device supports PME# from and the D1 and D2
support bits are cached in the corresponding struct pci_dev, the PCI
device PM code can be simplified quite a bit.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
PCI Express ASPM defines a protocol for PCI Express components in the D0
state to reduce Link power by placing their Links into a low power state
and instructing the other end of the Link to do likewise. This
capability allows hardware-autonomous, dynamic Link power reduction
beyond what is achievable by software-only controlled power management.
However, The device should be configured by software appropriately.
Enabling ASPM will save power, but will introduce device latency.
This patch adds ASPM support in Linux. It introduces a global policy for
ASPM, a sysfs file /sys/module/pcie_aspm/parameters/policy can control
it. The interface can be used as a boot option too. Currently we have
below setting:
-default, BIOS default setting
-powersave, highest power saving mode, enable all available ASPM
state and clock power management
-performance, highest performance, disable ASPM and clock power
management
By default, the 'default' policy is used currently.
In my test, power difference between powersave mode and performance mode
is about 1.3w in a system with 3 PCIE links.
Note: some devices might not work well with aspm, either because chipset
issue or device issue. The patch provide API (pci_disable_link_state),
driver can disable ASPM for specific device.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit 6c723d5bd8.
It caused build errors on non-x86 platforms, config file confusion, and
even some boot errors on some x86-64 boxes. All around, not quite ready
for prime-time :(
Cc: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PCI Express ASPM defines a protocol for PCI Express components in the D0
state to reduce Link power by placing their Links into a low power state
and instructing the other end of the Link to do likewise. This
capability allows hardware-autonomous, dynamic Link power reduction
beyond what is achievable by software-only controlled power management.
However, The device should be configured by software appropriately.
Enabling ASPM will save power, but will introduce device latency.
This patch adds ASPM support in Linux. It introduces a global policy for
ASPM, a sysfs file /sys/module/pcie_aspm/parameters/policy can control
it. The interface can be used as a boot option too. Currently we have
below setting:
-default, BIOS default setting
-powersave, highest power saving mode, enable all available ASPM
state
and clock power management
-performance, highest performance, disable ASPM and clock power
management
By default, the 'default' policy is used currently.
In my test, power difference between powersave mode and performance mode
is about 1.3w in a system with 3 PCIE links.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Modify PCI Bridge Control ISA flag for clarity
This patch changes PCI_BRIDGE_CTL_NO_ISA to PCI_BRIDGE_CTL_ISA
and modifies it's clarifying comment and locations where used.
The change reduces the chance of future confusion since it makes
the set/unset meaning of the bit the same in both the bridge
control register and bridge_ctl field of the pci_bus struct.
Signed-off-by: Gary Hade <garyhade@us.ibm.com>
Acked-by: Linas Vepstas <linas@austin.ibm.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These IDs are in pciutils, but haven't been added to the kernel
yet.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Newer tg3 devices shuffle around the registers in PCI configuration
space. This patch changes the way the driver accesses the PCI
capabilities registers. Hardcoded register locations are replaced with
offsets from pci_find_capability() return values.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two ways pci_save_state and pci_restore_state are used. As
helper functions during suspend/resume, and as helper functions around
a hardware reset event. When used as helper functions around a hardware
reset event there is no reason to believe the calls will be paired, nor
is there a good reason to believe that if we restore the msi state from
before the reset that it will match the current msi state. Since arch
code may change the msi message without going through the driver, drivers
currently do not have enough information to even know when to call
pci_save_state to ensure they will have msi state in sync with the other
kernel irq reception data structures.
It turns out the solution is straight forward, cache the state in the
existing msi data structures (not the magic pci saved things) and
have the msi code update the cached state each time we write to the hardware.
This means we never need to read the hardware to figure out what the hardware
state should be.
By modifying the caching in this manner we get to remove our save_state
routines and only need to provide restore_state routines.
The only fields that were at all tricky to regenerate were the msi and msi-x
control registers and the way we regenerate them currently is a bit dependent
upon assumptions on how we use the allow msi registers to be configured and used
making the code a little bit brittle. If we ever change what cases we allow
or how we configure the msi bits we can address the fragility then.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In some cases when we are not using msi we need a way to ensure that the
hardware does not have an msi capability enabled. Currently the code has been
calling disable_msi_mode to try and achieve that. However disable_msi_mode
has several other side effects and is only available when msi support is
compiled in so it isn't really appropriate.
Instead this patch implements pci_msi_off which disables all msi and msix
capabilities unconditionally with no additional side effects.
pci_disable_device was redundantly clearing the bus master enable flag and
clearing the msi enable bit. A device that is not allowed to perform bus
mastering operations cannot generate intx or msi interrupt messages as those
are essentially a special case of dma, and require bus mastering. So the call
in pci_disable_device to disable msi capabilities was redundant.
quirk_pcie_pxh also called disable_msi_mode and is updated to use pci_msi_off.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a few #defines for grabbing and working with the address fields
in a HT_CAPTYPE_MSI_MAPPING capability. All from the HT spec v3.00.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are already several places in the kernel that want to search a PCI
device for a given Hypertransport capability. Although this is possible
using pci_find_capability() etc., it makes sense to encapsulate that
logic in a helper - pci_find_ht_capability().
To cater for searching exhaustively for a capability, we also provide
pci_find_next_ht_capability().
We also need to cater for the fact that the HT capability fields may be
either 3 or 5 bits wide. pci_find_ht_capability() deals with this for you,
but callers using the #defines directly must handle that themselves.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move some MSI-X #defines into pci_regs.h so they can be used
outside of drivers/pci.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Due to hardware errata, TSO must be disabled if the PCI Express clock
request is enabled on 5906. The chip may hang when transmitting TSO
frames if CLKREQ is enabled.
Update version to 3.69.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds defines for the hypertransport capability subtypes and starts
using them a little.
[akpm@osdl.org: fix typo]
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
0x08 is the HT capability, while PCI_CAP_ID_HT_IRQCONF would be
the subtype 0x80 that mpic_scan_ht_pic() uses.
Rename PCI_CAP_ID_HT_IRQCONF into PCI_CAP_ID_HT.
And by the way, use it in the ipath driver instead of defining its
own HT_CAPABILITY_ID.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add new defines of PCI-Express AER registers and their bits into file
include/linux/pci_regs.h.
Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the vendor-specific extended capability PCI_CAP_ID_VNDR. It is required
by the Myri-10G Ethernet driver.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds some very basic support for the new machines, including the
Quad G5 (tested), and other new dual core based machines and iMac G5
iSight (untested). This is still experimental ! There is no thermal
control yet, there is no proper handing of MSIs, etc.. but it
boots, I have all 4 cores up on my machine. Compared to the previous
version of this patch, this one adds DART IOMMU support for the U4
chipset and thus should work fine on setups with more than 2Gb of RAM.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some PCI devices (e.g. 3c905B, 3c556B) lose all configuration
(including BARs) when transitioning from D3hot->D0. This leaves such
a device in an inaccessible state. The patch below causes the BARs
to be restored when enabling such a device, so that its driver will
be able to access it.
The patch also adds pci_restore_bars as a new global symbol, and adds a
correpsonding EXPORT_SYMBOL_GPL for that.
Some firmware (e.g. Thinkpad T21) leaves devices in D3hot after a
(re)boot. Most drivers call pci_enable_device very early, so devices
left in D3hot that lose configuration during the D3hot->D0 transition
will be inaccessible to their drivers.
Drivers could be modified to account for this, but it would
be difficult to know which drivers need modification. This is
especially true since often many devices are covered by the same
driver. It likely would be necessary to replicate code across dozens
of drivers.
The patch below should trigger only when transitioning from D3hot->D0
(or at boot), and only for devices that have the "no soft reset" bit
cleared in the PM control register. I believe it is safe to include
this patch as part of the PCI infrastructure.
The cleanest implementation of pci_restore_bars was to call
pci_update_resource. Unfortunately, that does not currently exist
for the sparc64 architecture. The patch below includes a null
implemenation of pci_update_resource for sparc64.
Some have expressed interest in making general use of the the
pci_restore_bars function, so that has been exported to GPL licensed
modules.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This cleans up some of the #ifdef CONFIG_PCI stuff up, and moves the pci register
info out to a separate file, where it belongs. Eventually we can stop including
this file from within pci.h, but lots of code needs to be audited first.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sheng Yang