This adds support for the U9540 variant of the U8500 series. This
is an application processor without internal modem. This is the
most basic part with ASIC ID, CPU-related fixes, IRQ list, register
ranges, timer, UART, and L2 cache setup. This is based on a patch
by Michel Jaouen which was rewritten to fit with the latest 3.3
kernel.
ChangeLog v1->v2: deleted the irqs-db9540.h file since we expect to
migrate to using Device Tree for getting the IRQs to devices.
ChangeLog v2->v3: introduced a fixed virtual offset for the ROM
as suggested by Arnd Bergmann.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sebastien Pasdeloup <sebastien.pasdeloup-nonst@stericsson.com>
Signed-off-by: Michel Jaouen <michel.jaouen@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The clock for the smp_twd block is not equal to the CPU
frequency, actually it is divided by two, so fix this,
and set the initial frequency to half of 1GHz which is
the most common case.
Reported-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The DB8500 ED (Early Drop) and V1 are only available inside of
ST-Ericsson or partners, we have actively replaced and scrapped
these prototypes. All Nova products on the open market (such as
the Snowball board) are based on V2 and later ASIC variants.
So let us focus on supporting the silicon that will be used and
delete this to get a clear overview.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SMP TWD on the ux500 will change frequency at the same time as
the CPU. Loop back the frequency presented from the CPU into a
clock that is looked up by the SMP TWD driver with the new cpufreq
notifier hook.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
MUSB driver has been updated to separate out BSP layer
from its generic parts, as separate driver. This patch
configures the clock with the new platform driver name.
Signed-off-by: Mian Yousaf Kaukab <mian-yousaf.kaukab@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The clock speed for the SD/MMC clock was incorrect, rectify it.
Signed-off-by: Philippe Langlais <philippe.langlais@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To allow the possiblity of building U8500 and U5500 support in the same
image.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
[Rebased to latest changes in Russells tree]
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
The DB5500 PER6 clock rate is the same as the DB8500 one, i.e. 133.33 MHz.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
U5500 now boots from sdi0 (onboard eMMC).
Change machine type to U5500.
Adjust uart and sdi0 clock rates for u5500.
All necessary clocks must be enabled before Linux starts because
there is no clock tree support in u5500 yet.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
PRCM_TCR enables the various timers in the system. This must be achieved
before any of the MTUs are usable for kernel usage. Explicit enabling of
this in the kernel makes it independent of bootloader actions.
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
factorise some generic infrastructure to assist looking up struct clks
for the ARM & SH architecture.
as the code is identical at 99%
put the arch specific code for allocation as example in asm/clkdev.h
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a dummy clk definition for the APB pclk signal on all platforms
using the AMBA bus infrastructure. This ensures that these platforms
continue to work when the core amba bus code controls the APB pclk.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The MTU wallclock timing fix-up patch was hardwired to the DB8500
causing a regression. This makes it work on the DB5500 as well.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This completes the DMA40 support with the platform-specific
configuration for U8500/DB8500.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Reviewed-by: Alessandro Rubini <rubini@unipv.it>
Cc: STEricsson_nomadik_linux@list.st.com
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
[fixed up dma40_{tx|rx}_map declaration/initialization]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This adjusts the clockrate for the MTU timer. On the different
UX500 variants this rate is different. The platform can also have
been set up at hardware initialization, bootloader or early init
for different clock speeds. To have the clock framework available
early so the timers can use them, the clock initialization for
Nomadik and ux500 is moved to IRQ init time. A custom per-clock
callback is added to handle special cases like this.
This solves a user-visible bug: without this patch the current
UX500 platforms will not be synchronized to wall-clock time and
the platform will drift in time.
Acked-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add clocks with appropriate names in platforms that use it, and use the
clk API in nomadik-gpio.
Acked-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add basic support for the U5500 platform.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Implement clock gating support for the u8500 clocks.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Most machine classes want some way to register a block of clk_lookup
structures, and most do it by implementing a clks_register() type
function which walks an array, or by open-coding a loop.
Consolidate all this into clkdev_add_table().
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Adds basic clock framework to the U8500 platform.
Currently it just uses the clock lookup table
and add the each entry to the clkdevice. More
complex clock management to follow soon
Signed-off-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Walleij