In pci_pm_complete() there are checks to decide whether or not to
resume devices that were left in runtime-suspend during the preceding
system-wide transition into a sleep state. They involve checking the
current power state of the device and comparing it with the power
state of it set before the preceding system-wide transition, but the
platform component of the device's power state is not handled
correctly in there.
Namely, on platforms with ACPI, the device power state information
needs to be updated with care, so that the reference counters of
power resources used by the device (if any) are set to ensure that
the refreshed power state of it will be maintained going forward.
To that end, introduce a new ->refresh_state() platform PM callback
for PCI devices, for asking the platform to refresh the device power
state data and ensure that the corresponding power state will be
maintained going forward, make it invoke acpi_device_update_power()
(for devices with ACPI PM) on platforms with ACPI and make
pci_pm_complete() use it, through a new pci_refresh_power_state()
wrapper function.
Fixes: a0d2a959d3 (PCI: Avoid unnecessary resume after direct-complete)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Currently Linux does not follow PCIe spec regarding the required delays
after reset. A concrete example is a Thunderbolt add-in-card that
consists of a PCIe switch and two PCIe endpoints:
+-1b.0-[01-6b]----00.0-[02-6b]--+-00.0-[03]----00.0 TBT controller
+-01.0-[04-36]-- DS hotplug port
+-02.0-[37]----00.0 xHCI controller
\-04.0-[38-6b]-- DS hotplug port
The root port (1b.0) and the PCIe switch downstream ports are all PCIe
gen3 so they support 8GT/s link speeds.
We wait for the PCIe hierarchy to enter D3cold (runtime):
pcieport 0000:00:1b.0: power state changed by ACPI to D3cold
When it wakes up from D3cold, according to the PCIe 4.0 section 5.8 the
PCIe switch is put to reset and its power is re-applied. This means that
we must follow the rules in PCIe 4.0 section 6.6.1.
For the PCIe gen3 ports we are dealing with here, the following applies:
With a Downstream Port that supports Link speeds greater than 5.0
GT/s, software must wait a minimum of 100 ms after Link training
completes before sending a Configuration Request to the device
immediately below that Port. Software can determine when Link training
completes by polling the Data Link Layer Link Active bit or by setting
up an associated interrupt (see Section 6.7.3.3).
Translating this into the above topology we would need to do this (DLLLA
stands for Data Link Layer Link Active):
pcieport 0000:00:1b.0: wait for 100ms after DLLLA is set before access to 0000:01:00.0
pcieport 0000:02:00.0: wait for 100ms after DLLLA is set before access to 0000:03:00.0
pcieport 0000:02:02.0: wait for 100ms after DLLLA is set before access to 0000:37:00.0
I've instrumented the kernel with additional logging so we can see the
actual delays the kernel performs:
pcieport 0000:00:1b.0: power state changed by ACPI to D0
pcieport 0000:00:1b.0: waiting for D3cold delay of 100 ms
pcieport 0000:00:1b.0: waking up bus
pcieport 0000:00:1b.0: waiting for D3hot delay of 10 ms
pcieport 0000:00:1b.0: restoring config space at offset 0x2c (was 0x60, writing 0x60)
...
pcieport 0000:00:1b.0: PME# disabled
pcieport 0000:01:00.0: restoring config space at offset 0x3c (was 0x1ff, writing 0x201ff)
...
pcieport 0000:01:00.0: PME# disabled
pcieport 0000:02:00.0: restoring config space at offset 0x3c (was 0x1ff, writing 0x201ff)
...
pcieport 0000:02:00.0: PME# disabled
pcieport 0000:02:01.0: restoring config space at offset 0x3c (was 0x1ff, writing 0x201ff)
...
pcieport 0000:02:01.0: restoring config space at offset 0x4 (was 0x100000, writing 0x100407)
pcieport 0000:02:01.0: PME# disabled
pcieport 0000:02:02.0: restoring config space at offset 0x3c (was 0x1ff, writing 0x201ff)
...
pcieport 0000:02:02.0: PME# disabled
pcieport 0000:02:04.0: restoring config space at offset 0x3c (was 0x1ff, writing 0x201ff)
...
pcieport 0000:02:04.0: PME# disabled
pcieport 0000:02:01.0: PME# enabled
pcieport 0000:02:01.0: waiting for D3hot delay of 10 ms
pcieport 0000:02:04.0: PME# enabled
pcieport 0000:02:04.0: waiting for D3hot delay of 10 ms
thunderbolt 0000:03:00.0: restoring config space at offset 0x14 (was 0x0, writing 0x8a040000)
...
thunderbolt 0000:03:00.0: PME# disabled
xhci_hcd 0000:37:00.0: restoring config space at offset 0x10 (was 0x0, writing 0x73f00000)
...
xhci_hcd 0000:37:00.0: PME# disabled
For the switch upstream port (01:00.0) we wait for 100ms but not taking
into account the DLLLA requirement. We then wait 10ms for D3hot -> D0
transition of the root port and the two downstream hotplug ports. This
means that we deviate from what the spec requires.
Performing the same check for system sleep (s2idle) transitions we can
see following when resuming from s2idle:
pcieport 0000:00:1b.0: power state changed by ACPI to D0
pcieport 0000:00:1b.0: restoring config space at offset 0x2c (was 0x60, writing 0x60)
...
pcieport 0000:01:00.0: restoring config space at offset 0x3c (was 0x1ff, writing 0x201ff)
...
pcieport 0000:02:02.0: restoring config space at offset 0x3c (was 0x1ff, writing 0x201ff)
pcieport 0000:02:02.0: restoring config space at offset 0x2c (was 0x0, writing 0x0)
pcieport 0000:02:01.0: restoring config space at offset 0x3c (was 0x1ff, writing 0x201ff)
pcieport 0000:02:04.0: restoring config space at offset 0x3c (was 0x1ff, writing 0x201ff)
pcieport 0000:02:02.0: restoring config space at offset 0x28 (was 0x0, writing 0x0)
pcieport 0000:02:00.0: restoring config space at offset 0x3c (was 0x1ff, writing 0x201ff)
pcieport 0000:02:02.0: restoring config space at offset 0x24 (was 0x10001, writing 0x1fff1)
pcieport 0000:02:01.0: restoring config space at offset 0x2c (was 0x0, writing 0x60)
pcieport 0000:02:02.0: restoring config space at offset 0x20 (was 0x0, writing 0x73f073f0)
pcieport 0000:02:04.0: restoring config space at offset 0x2c (was 0x0, writing 0x60)
pcieport 0000:02:01.0: restoring config space at offset 0x28 (was 0x0, writing 0x60)
pcieport 0000:02:00.0: restoring config space at offset 0x2c (was 0x0, writing 0x0)
pcieport 0000:02:02.0: restoring config space at offset 0x1c (was 0x101, writing 0x1f1)
pcieport 0000:02:04.0: restoring config space at offset 0x28 (was 0x0, writing 0x60)
pcieport 0000:02:01.0: restoring config space at offset 0x24 (was 0x10001, writing 0x1ff10001)
pcieport 0000:02:00.0: restoring config space at offset 0x28 (was 0x0, writing 0x0)
pcieport 0000:02:02.0: restoring config space at offset 0x18 (was 0x0, writing 0x373702)
pcieport 0000:02:04.0: restoring config space at offset 0x24 (was 0x10001, writing 0x49f12001)
pcieport 0000:02:01.0: restoring config space at offset 0x20 (was 0x0, writing 0x73e05c00)
pcieport 0000:02:00.0: restoring config space at offset 0x24 (was 0x10001, writing 0x1fff1)
pcieport 0000:02:04.0: restoring config space at offset 0x20 (was 0x0, writing 0x89f07400)
pcieport 0000:02:01.0: restoring config space at offset 0x1c (was 0x101, writing 0x5151)
pcieport 0000:02:00.0: restoring config space at offset 0x20 (was 0x0, writing 0x8a008a00)
pcieport 0000:02:02.0: restoring config space at offset 0xc (was 0x10000, writing 0x10020)
pcieport 0000:02:04.0: restoring config space at offset 0x1c (was 0x101, writing 0x6161)
pcieport 0000:02:01.0: restoring config space at offset 0x18 (was 0x0, writing 0x360402)
pcieport 0000:02:00.0: restoring config space at offset 0x1c (was 0x101, writing 0x1f1)
pcieport 0000:02:04.0: restoring config space at offset 0x18 (was 0x0, writing 0x6b3802)
pcieport 0000:02:02.0: restoring config space at offset 0x4 (was 0x100000, writing 0x100407)
pcieport 0000:02:00.0: restoring config space at offset 0x18 (was 0x0, writing 0x30302)
pcieport 0000:02:01.0: restoring config space at offset 0xc (was 0x10000, writing 0x10020)
pcieport 0000:02:04.0: restoring config space at offset 0xc (was 0x10000, writing 0x10020)
pcieport 0000:02:00.0: restoring config space at offset 0xc (was 0x10000, writing 0x10020)
pcieport 0000:02:01.0: restoring config space at offset 0x4 (was 0x100000, writing 0x100407)
pcieport 0000:02:04.0: restoring config space at offset 0x4 (was 0x100000, writing 0x100407)
pcieport 0000:02:00.0: restoring config space at offset 0x4 (was 0x100000, writing 0x100407)
xhci_hcd 0000:37:00.0: restoring config space at offset 0x10 (was 0x0, writing 0x73f00000)
...
thunderbolt 0000:03:00.0: restoring config space at offset 0x14 (was 0x0, writing 0x8a040000)
This is even worse. None of the mandatory delays are performed. If this
would be S3 instead of s2idle then according to PCI FW spec 3.2 section
4.6.8. there is a specific _DSM that allows the OS to skip the delays
but this platform does not provide the _DSM and does not go to S3 anyway
so no firmware is involved that could already handle these delays.
In this particular Intel Coffee Lake platform these delays are not
actually needed because there is an additional delay as part of the ACPI
power resource that is used to turn on power to the hierarchy but since
that additional delay is not required by any of standards (PCIe, ACPI)
it is not present in the Intel Ice Lake, for example where missing the
mandatory delays causes pciehp to start tearing down the stack too early
(links are not yet trained).
For this reason, change the PCIe portdrv PM resume hooks so that they
perform the mandatory delays before the downstream component gets
resumed. We perform the delays before port services are resumed because
otherwise pciehp might find that the link is not up (even if it is just
training) and tears-down the hierarchy.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The code in pci_dev_keep_suspended() is relatively hard to follow due
to the negative checks in it and in its callers and the function has
a possible side-effect (disabling the PME) which doesn't really match
its role.
For this reason, move the PME disabling from pci_dev_keep_suspended()
to a separate function and change the semantics (and name) of the
rest of it, so that 'true' is returned when the device needs to be
resumed (and not the other way around). Change the callers of
pci_dev_keep_suspended() accordingly.
While at it, make the code flow in pci_pm_poweroff() reflect the
pci_pm_suspend() more closely to avoid arbitrary differences between
them.
This is a cosmetic change with no intention to alter behavior.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
If a multi-function device's bandwidth is already limited when it is
enumerated, a message is logged only for function 0. By contrast, when
downtraining occurs after enumeration, a message is logged for all
functions. That's because the former uses pcie_report_downtraining(),
whereas the latter uses __pcie_print_link_status() (which doesn't filter
functions != 0). I am seeing this happen on a MacBookPro9,1 with a GPU
(function 0) and an integrated HDA controller (function 1).
Avoid this incongruence by calling pcie_report_downtraining() in both
cases.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alexandru Gagniuc <alex.gagniuc@dellteam.com>
This file makes use of definitions provided in <linux/pci.h>. This only
compiles when <linux/pci.h> is included beforehand, and creates a nasty
include dependency. Instead, just include the correct file.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
- Cache VF config space size to optimize enumeration of many VFs
(KarimAllah Ahmed)
- Remove unnecessary <linux/pci-ats.h> include (Bjorn Helgaas)
* pci/virtualization:
PCI/IOV: Remove unnecessary include of <linux/pci-ats.h>
PCI/IOV: Use VF0 cached config space size for other VFs
Cache the config space size from VF0 and use it for all other VFs instead
of reading it from the config space of each VF. We assume that it will be
the same across all associated VFs.
This is an optimization when enabling SR-IOV on a device with many VFs.
Signed-off-by: KarimAllah Ahmed <karahmed@amazon.de>
[bhelgaas: use CONFIG_PCI_IOV (not CONFIG_PCI_ATS)]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In order to have better power management for Thunderbolt PCIe chains,
Windows enables power management for native PCIe hotplug ports if there is
the following ACPI _DSD attached to the root port:
Name (_DSD, Package () {
ToUUID ("6211e2c0-58a3-4af3-90e1-927a4e0c55a4"),
Package () {
Package () {"HotPlugSupportInD3", 1}
}
})
This is also documented in:
https://docs.microsoft.com/en-us/windows-hardware/drivers/pci/dsd-for-pcie-root-ports#identifying-pcie-root-ports-supporting-hot-plug-in-d3
Do the same in Linux by introducing new firmware PM callback
(->bridge_d3()) and then implement it for ACPI based systems so that the
above property is checked.
There is one catch, though. The initial pci_dev->bridge_d3 is set before
the root port has ACPI companion bound (the device is not added to the PCI
bus either) so we need to look up the ACPI companion manually in that case
in acpi_pci_bridge_d3().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Bring surprise removals and permanent failures together so we no longer
need separate flags. The implementation enforces that error handling will
not be able to override a surprise removal's permanent channel failure.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
We don't need to be paranoid about the topology changing while handling an
error. If the device has changed in a hotplug capable slot, we can rely on
the presence detection handling to react to a changing topology.
Restore the fatal error handling behavior that existed before merging DPC
with AER with 7e9084b367 ("PCI/AER: Handle ERR_FATAL with removal and
re-enumeration of devices").
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
The secondary bus reset may have link side effects that a hotplug capable
port may incorrectly react to. Use the slot specific reset for hotplug
ports, fixing the undesirable link down-up handling during error
recovering.
Signed-off-by: Keith Busch <keith.busch@intel.com>
[bhelgaas: fold in
https://lore.kernel.org/linux-pci/20180926152326.14821-1-keith.busch@intel.com
for issue reported by Stephen Rothwell <sfr@canb.auug.org.au>]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
This patch provides DPC save and restore capabilities. This is necessary
for the driver to observe DPC events in the event the configuration space
needs to be restored after a reset.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
- To avoid bus errors, enable PASID only if entire path supports End-End
TLP prefixes (Sinan Kaya)
- Unify slot and bus reset functions and remove hotplug knowledge from
callers (Sinan Kaya)
- Add Function-Level Reset quirks for Intel and Samsung NVMe devices to
fix guest reboot issues (Alex Williamson)
- Add function 1 DMA alias quirk for Marvell 88SS9183 PCIe SSD Controller
(Bjorn Helgaas)
* pci/virtualization:
PCI: Add function 1 DMA alias quirk for Marvell 88SS9183
PCI: Delay after FLR of Intel DC P3700 NVMe
PCI: Disable Samsung SM961/PM961 NVMe before FLR
PCI: Export pcie_has_flr()
PCI: Rename pci_try_reset_bus() to pci_reset_bus()
PCI: Deprecate pci_reset_bus() and pci_reset_slot() functions
PCI: Unify try slot and bus reset API
PCI: Hide pci_reset_bridge_secondary_bus() from drivers
IB/hfi1: Use pci_try_reset_bus() for initiating PCI Secondary Bus Reset
PCI: Handle error return from pci_reset_bridge_secondary_bus()
PCI/IOV: Tidy pci_sriov_set_totalvfs()
PCI: Enable PASID only if entire path supports End-End TLP prefixes
# Conflicts:
# drivers/pci/hotplug/pciehp_hpc.c
- Clean up devm_of_pci_get_host_bridge_resources() resource allocation
(Jan Kiszka)
- Fixup resizable BARs after suspend/resume (Christian König)
- Make "pci=earlydump" generic (Sinan Kaya)
- Fix ROM BAR access routines to stay in bounds and check for signature
correctly (Rex Zhu)
* pci/resource:
PCI: Make pci_get_rom_size() static
PCI: Add check code for last image indicator not set
PCI: Avoid accessing memory outside the ROM BAR
PCI: Make early dump functionality generic
PCI: Cleanup PCI_REBAR_CTRL_BAR_SHIFT handling
PCI: Restore resized BAR state on resume
PCI: Clean up resource allocation in devm_of_pci_get_host_bridge_resources()
# Conflicts:
# Documentation/admin-guide/kernel-parameters.txt
- Add "pci=disable_acs_redir=" parameter to disable ACS redirection for
peer-to-peer DMA support (we don't have the peer-to-peer support yet;
this is just one piece) (Logan Gunthorpe)
* pci/peer-to-peer:
PCI: Add ACS Redirect disable quirk for Intel Sunrise Point
PCI: Add device-specific ACS Redirect disable infrastructure
PCI: Convert device-specific ACS quirks from NULL termination to ARRAY_SIZE
PCI: Add "pci=disable_acs_redir=" parameter for peer-to-peer support
PCI: Allow specifying devices using a base bus and path of devfns
PCI: Make specifying PCI devices in kernel parameters reusable
PCI: Hide ACS quirk declarations inside PCI core
- Work around IDT switch ACS Source Validation erratum (James
Puthukattukaran)
- Emit diagnostics for all cases of PCIe Link downtraining (Links
operating slower than they're capable of) (Alexandru Gagniuc)
- Skip VFs when configuring Max Payload Size (Myron Stowe)
- Reduce Root Port Max Payload Size if necessary when hot-adding a device
below it (Myron Stowe)
* pci/enumeration:
PCI: Match Root Port's MPS to endpoint's MPSS as necessary
PCI: Skip MPS logic for Virtual Functions (VFs)
PCI: Check for PCIe Link downtraining
PCI: Workaround IDT switch ACS Source Validation erratum
- Decode AER errors with names similar to "lspci" (Tyler Baicar)
- Expose AER statistics in sysfs (Rajat Jain)
- Clear AER status bits selectively based on the type of recovery (Oza
Pawandeep)
- Honor "pcie_ports=native" even if HEST sets FIRMWARE_FIRST (Alexandru
Gagniuc)
- Don't clear AER status bits if we're using the "Firmware-First"
strategy where firmware owns the registers (Alexandru Gagniuc)
* pci/aer:
PCI/AER: Don't clear AER bits if error handling is Firmware-First
PCI/AER: Remove duplicate PCI_EXP_AER_FLAGS definition
PCI/portdrv: Remove pcie_portdrv_err_handler.slot_reset
PCI/AER: Clear device status bits during ERR_COR handling
PCI/AER: Clear device status bits during ERR_FATAL and ERR_NONFATAL
PCI/AER: Remove ERR_FATAL code from ERR_NONFATAL path
PCI/AER: Factor out ERR_NONFATAL status bit clearing
PCI/AER: Clear only ERR_NONFATAL bits during non-fatal recovery
PCI/AER: Clear only ERR_FATAL status bits during fatal recovery
PCI/AER: Honor "pcie_ports=native" even if HEST sets FIRMWARE_FIRST
PCI/AER: Add sysfs attributes for rootport cumulative stats
PCI/AER: Add sysfs attributes to provide AER stats and breakdown
PCI/AER: Define aer_stats structure for AER capable devices
PCI/AER: Move internal declarations to drivers/pci/pci.h
PCI/AER: Adopt lspci names for AER error decoding
PCI/AER: Expose internal API for obtaining AER information
# Conflicts:
# drivers/pci/pci.h
When both ends of a PCIe Link are capable of a higher bandwidth than is
currently in use, the Link is said to be "downtrained". A downtrained Link
may indicate hardware or configuration problems in the system, but it's
hard to identify such Links from userspace.
Refactor pcie_print_link_status() so it continues to always print PCIe
bandwidth information, as several NIC drivers desire.
Add a new internal __pcie_print_link_status() to emit a message only when a
device's bandwidth is constrained by the fabric and call it from the PCI
core for all devices, which identifies all downtrained Links. It also
emits messages for a few cases that are technically not downtrained, such
as a x4 device in an open-ended x1 slot.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[bhelgaas: changelog, move __pcie_print_link_status() declaration to
drivers/pci/, rename pcie_check_upstream_link() to
pcie_report_downtraining()]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Intel Sunrise Point (SPT) PCH hardware has an implementation of the ACS
bits that does not comply with the PCIe standard. To deal with this we
need device-specific quirks to disable ACS redirection.
Add a new pci_dev_specific_disable_acs_redir() quirk and a new
.disable_acs_redir() function pointer for use by non-compliant devices. No
functional change intended.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
[bhelgaas: split to separate patch, move
pci_dev_specific_disable_acs_redir() declarations to drivers/pci/pci.h]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Move declarations for these functions:
pci_dev_specific_acs_enabled()
pci_dev_specific_enable_acs()
from include/linux/pci.h to drivers/pci/pci.h because nothing outside the
PCI core needs to use them.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When a PCI device is detected, pdev->is_added is set to 1 and proc and
sysfs entries are created.
When the device is removed, pdev->is_added is checked for one and then
device is detached with clearing of proc and sys entries and at end,
pdev->is_added is set to 0.
is_added and is_busmaster are bit fields in pci_dev structure sharing same
memory location.
A strange issue was observed with multiple removal and rescan of a PCIe
NVMe device using sysfs commands where is_added flag was observed as zero
instead of one while removing device and proc,sys entries are not cleared.
This causes issue in later device addition with warning message
"proc_dir_entry" already registered.
Debugging revealed a race condition between the PCI core setting the
is_added bit in pci_bus_add_device() and the NVMe driver reset work-queue
setting the is_busmaster bit in pci_set_master(). As these fields are not
handled atomically, that clears the is_added bit.
Move the is_added bit to a separate private flag variable and use atomic
functions to set and retrieve the device addition state. This avoids the
race because is_added no longer shares a memory location with is_busmaster.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200283
Signed-off-by: Hari Vyas <hari.vyas@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Clear the device status bits while handling both ERR_FATAL and ERR_NONFATAL
cases.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: rename to pci_aer_clear_device_status(), declare internal to PCI
core instead of exposing it everywhere]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
During recovery from fatal errors, we previously called
pci_cleanup_aer_uncorrect_error_status(), which cleared *all* uncorrectable
error status bits (both ERR_FATAL and ERR_NONFATAL).
Instead, call a new pci_aer_clear_fatal_status() that clears only the
ERR_FATAL bits (as indicated by the PCI_ERR_UNCOR_SEVER register).
Based-on-patch-by: Oza Pawandeep <poza@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Rename pci_reset_bridge_secondary_bus() to pci_bridge_secondary_bus_reset()
and move the declaration from linux/pci.h to drivers/pci.h to be used
internally in PCI directory only.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add sysfs attributes to provide total and breakdown of the AERs seen,
into different type of correctable, fatal and nonfatal errors:
/sys/bus/pci/devices/<dev>/aer_dev_correctable
/sys/bus/pci/devices/<dev>/aer_dev_fatal
/sys/bus/pci/devices/<dev>/aer_dev_nonfatal
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Define a structure to hold the AER statistics. There are 2 groups of
statistics: dev_* counters that are to be collected for all AER capable
devices and rootport_* counters that are collected for all (AER capable)
rootports only. Allocate and free this structure when device is added or
released (thus counters survive the lifetime of the device).
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Since pci_aer_init() and pci_no_aer() are used only internally, move their
declarations to the PCI internal header file. Also, no one cares about
return value of pci_aer_init(), so make it void.
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Export some common AER functions and structures for other PCI core drivers
to use. Since this is making the function externally visible inside the
PCI core, prepend "aer_" to the function name.
Signed-off-by: Keith Busch <keith.busch@intel.com>
[bhelgaas: move AER declarations from linux/aer.h to drivers/pci/pci.h]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
Some IDT switches incorrectly flag an ACS Source Validation error on
completions for config read requests even though PCIe r4.0, sec 6.12.1.1,
says that completions are never affected by ACS Source Validation. Here's
the text of IDT 89H32H8G3-YC, erratum #36:
Item #36 - Downstream port applies ACS Source Validation to Completions
Section 6.12.1.1 of the PCI Express Base Specification 3.1 states that
completions are never affected by ACS Source Validation. However,
completions received by a downstream port of the PCIe switch from a
device that has not yet captured a PCIe bus number are incorrectly
dropped by ACS Source Validation by the switch downstream port.
Workaround: Issue a CfgWr1 to the downstream device before issuing the
first CfgRd1 to the device. This allows the downstream device to capture
its bus number; ACS Source Validation no longer stops completions from
being forwarded by the downstream port. It has been observed that
Microsoft Windows implements this workaround already; however, some
versions of Linux and other operating systems may not.
When doing the first config read to probe for a device, if the device is
behind an IDT switch with this erratum:
1. Disable ACS Source Validation if enabled
2. Wait for device to become ready to accept config accesses (by using
the Config Request Retry Status mechanism)
3. Do a config write to the endpoint
4. Enable ACS Source Validation (if it was enabled to begin with)
The workaround suggested by IDT is basically only step 3, but we don't know
when the device is ready to accept config requests. That means we need to
do config reads until we receive a non-Config Request Retry Status, which
means we need to disable ACS SV temporarily.
Signed-off-by: James Puthukattukaran <james.puthukattukaran@oracle.com>
[bhelgaas: changelog, clean up whitespace, fold in unused variable fix
from Anders Roxell <anders.roxell@linaro.org>]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Move early dump functionality into common code so that it is available for
all architectures. No need to carry arch-specific reads around as the read
hooks are already initialized by the time pci_setup_device() is getting
called during scan.
Tested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
The TotalVFs register in the SR-IOV capability is the hardware limit on the
number of VFs. A PF driver can limit the number of VFs further with
pci_sriov_set_totalvfs(). When the PF driver is removed, reset any VF
limit that was imposed by the driver because that limit may not apply to
other drivers.
Before 8d85a7a4f2 ("PCI/IOV: Allow PF drivers to limit total_VFs to 0"),
pci_sriov_set_totalvfs(pdev, 0) meant "we can enable TotalVFs virtual
functions", and the nfp driver used that to remove the VF limit when the
driver unloads.
8d85a7a4f2 broke that because instead of removing the VF limit,
pci_sriov_set_totalvfs(pdev, 0) actually sets the limit to zero, and that
limit persists even if another driver is loaded.
We could fix that by making the nfp driver reset the limit when it unloads,
but it seems more robust to do it in the PCI core instead of relying on the
driver.
The regression scenario is:
nfp_pci_probe (driver 1)
...
nfp_pci_remove
pci_sriov_set_totalvfs(pf->pdev, 0) # limits VFs to 0
...
nfp_pci_probe (driver 2)
nfp_rtsym_read_le("nfd_vf_cfg_max_vfs")
# no VF limit from firmware
Now driver 2 is broken because the VF limit is still 0 from driver 1.
Fixes: 8d85a7a4f2 ("PCI/IOV: Allow PF drivers to limit total_VFs to 0")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
[bhelgaas: changelog, rename functions]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
- reduce Keystone "link already up" log level (Fabio Estevam)
- move private DT functions to drivers/pci/ (Rob Herring)
- factor out dwc CONFIG_PCI Kconfig dependencies (Rob Herring)
- add DesignWare support to the endpoint test driver (Gustavo Pimentel)
- add DesignWare support for endpoint mode (Gustavo Pimentel)
- use devm_ioremap_resource() instead of devm_ioremap() in dra7xx and
artpec6 (Gustavo Pimentel)
- fix Qualcomm bitwise NOT issue (Dan Carpenter)
- add Qualcomm runtime PM support (Srinivas Kandagatla)
* lorenzo/pci/dwc:
PCI: qcom: add runtime pm support to pcie_port
PCI: qcom: Fix a bitwise vs logical NOT typo
PCI: dwc: dra7xx: Use devm_ioremap_resource() instead of devm_ioremap()
PCI: dwc: artpec6: Use devm_ioremap_resource() instead of devm_ioremap()
misc: pci_endpoint_test: Add DesignWare EP entry
dt-bindings: PCI: designware: Add support for EP in DesignWare driver
PCI: dwc: Add support for EP mode
dt-bindings: PCI: designware: Example update
PCI: Move private DT related functions into private header
PCI: dwc: Move CONFIG_PCI depends to menu
PCI: dwc: Replace magic number by defines
PCI: dwc: Small computation improvement
PCI: dwc: Replace lower into upper case characters
PCI: dwc: Define maximum number of vectors
PCI: imx6: Remove space before tabs
PCI: keystone: Do not treat link up message as error
# Conflicts:
# include/linux/of_pci.h
Pass the service type to pcie_do_fatal_recovery() instead of assuming AER.
We will make DPC also use pcie_do_fatal_recovery(), and it needs to do
things a little differently for AER and DPC.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: split to separate patch]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move the error reporting callbacks from aerdrv_core.c to err.c, where they
can be used by DPC in addition to AER.
As part of aerdrv_core.c, these callbacks were built under CONFIG_PCIEAER.
Moving them to the new err.c means they will now be built under
CONFIG_PCIEPORTBUS, so adjust the definition of pci_uevent_ers() to match.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: in reset_link(), initialize "driver" even if CONFIG_PCIEAER is
unset, update pci_uevent_ers() #ifdef wrapper]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Clients such as hotplug and Downstream Port Containment (DPC) both need to
wait until a link becomes active or inactive.
Add a generic pcie_wait_link_active() interface and use it instead of
duplicating the code.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
The functions in linux/of_pci.h are primarily used by host bridge
drivers, so they can be private to drivers/pci/.
The remaining functions are still used mostly in host bridge drivers
that still live in arch specific code. Hopefully someday, those will get
moved into drivers/pci as well.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
- probe for device reset support during enumeration instead of runtime
(Bjorn Helgaas)
- add ACS quirk for Ampere (née APM) root ports (Feng Kan)
- add function 1 DMA alias quirk for Marvell 88SE9220 (Thomas
Vincent-Cross)
- protect device restore with device lock (Sinan Kaya)
- handle failure of FLR gracefully (Sinan Kaya)
- handle CRS (config retry status) after device resets (Sinan Kaya)
- skip various config reads for SR-IOV VFs as an optimization (KarimAllah
Ahmed)
* pci/virtualization:
PCI/IOV: Add missing prototypes for powerpc pcibios interfaces
PCI/IOV: Use VF0 cached config registers for other VFs
PCI/IOV: Skip BAR sizing for VFs
PCI/IOV: Skip INTx config reads for VFs
PCI: Wait for device to become ready after secondary bus reset
PCI: Add a return type for pci_reset_bridge_secondary_bus()
PCI: Wait for device to become ready after a power management reset
PCI: Rename pci_flr_wait() to pci_dev_wait() and make it generic
PCI: Handle FLR failure and allow other reset types
PCI: Protect restore with device lock to be consistent
PCI: Add function 1 DMA alias quirk for Marvell 88SE9220
PCI: Add ACS quirk for Ampere root ports
PCI: Remove redundant probes for device reset support
PCI: Probe for device reset support during enumeration
Conflicts:
include/linux/pci.h
- move pcieport_if.h to drivers/pci/pcie/ to encapsulate it (Frederick
Lawler)
- merge pcieport_if.h into portdrv.h (Bjorn Helgaas)
- move workaround for BIOS PME issue from portdrv to PCI core (Bjorn
Helgaas)
- completely disable portdrv with "pcie_ports=compat" (Bjorn Helgaas)
- remove portdrv link order dependency (Bjorn Helgaas)
- remove support for unused VC portdrv service (Bjorn Helgaas)
- simplify portdrv feature permission checking (Bjorn Helgaas)
- remove "pcie_hp=nomsi" parameter (use "pci=nomsi" instead) (Bjorn
Helgaas)
- remove unnecessary "pcie_ports=auto" parameter (Bjorn Helgaas)
- use cached AER capability offset (Frederick Lawler)
- don't enable DPC if BIOS hasn't granted AER control (Mika Westerberg)
- rename pcie-dpc.c to dpc.c (Bjorn Helgaas)
* pci/portdrv:
PCI/DPC: Rename from pcie-dpc.c to dpc.c
PCI/DPC: Do not enable DPC if AER control is not allowed by the BIOS
PCI/AER: Use cached AER Capability offset
PCI/portdrv: Rename and reverse sense of pcie_ports_auto
PCI/portdrv: Encapsulate pcie_ports_auto inside the port driver
PCI/portdrv: Remove unnecessary "pcie_ports=auto" parameter
PCI/portdrv: Remove "pcie_hp=nomsi" kernel parameter
PCI/portdrv: Remove unnecessary include of <linux/pci-aspm.h>
PCI/portdrv: Simplify PCIe feature permission checking
PCI/portdrv: Remove unused PCIE_PORT_SERVICE_VC
PCI/portdrv: Remove pcie_port_bus_type link order dependency
PCI/portdrv: Disable port driver in compat mode
PCI/PM: Clear PCIe PME Status bit for Root Complex Event Collectors
PCI/PM: Clear PCIe PME Status bit in core, not PCIe port driver
PCI/PM: Move pcie_clear_root_pme_status() to core
PCI/portdrv: Merge pcieport_if.h into portdrv.h
PCI/portdrv: Move pcieport_if.h to drivers/pci/pcie/
Conflicts:
drivers/pci/pcie/Makefile
drivers/pci/pcie/portdrv.h
Cache some config data from VF0 and use it for all other VFs instead of
reading it from the config space of each VF. We assume these items are the
same across all associated VFs:
Revision ID
Class Code
Subsystem Vendor ID
Subsystem ID
This is an optimization when enabling SR-IOV on a device with many VFs.
Signed-off-by: KarimAllah Ahmed <karahmed@amazon.de>
[bhelgaas: changelog, simplify comments, remove unused "device", test
CONFIG_PCI_IOV instead of CONFIG_PCI_ATS, rename functions]
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Add pcie_bandwidth_capable() to compute the max link bandwidth supported by
a device, based on the max link speed and width, adjusted by the encoding
overhead.
The maximum bandwidth of the link is computed as:
max_link_width * max_link_speed * (1 - encoding_overhead)
2.5 and 5.0 GT/s links use 8b/10b encoding, which reduces the raw bandwidth
available by 20%; 8.0 GT/s and faster links use 128b/130b encoding, which
reduces it by about 1.5%.
The result is in Mb/s, i.e., megabits/second, of raw bandwidth.
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
[bhelgaas: add 16 GT/s, adjust for pcie_get_speed_cap() and
pcie_get_width_cap() signatures, don't export outside drivers/pci]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add pcie_get_width_cap() to find the max link width supported by a device.
Change max_link_width_show() to use pcie_get_width_cap().
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
[bhelgaas: return width directly instead of error and *width, don't export
outside drivers/pci]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Add pcie_get_speed_cap() to find the max link speed supported by a device.
Change max_link_speed_show() to use pcie_get_speed_cap().
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
[bhelgaas: return speed directly instead of error and *speed, don't export
outside drivers/pci]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
The VPD-related structures are only used in vpd.c, so move them from
drivers/pci/pci.h to vpd.c. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move the VPD-related sysfs code from pci-sysfs.c to vpd.c. This follows
the pattern of pcie_aspm_create_sysfs_dev_files(). The goal is to
encapsulate all the VPD code and structures in vpd.c.
No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move pcie_clear_root_pme_status() from the port driver to the PCI core so
it will be available even when the port driver isn't present. No
functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Several of the interfaces defined in include/linux/pci-aspm.h are used only
internally from the PCI core:
pcie_aspm_init_link_state()
pcie_aspm_exit_link_state()
pcie_aspm_pm_state_change()
pcie_aspm_powersave_config_link()
pcie_aspm_create_sysfs_dev_files()
pcie_aspm_remove_sysfs_dev_files()
Move these to the internal drivers/pci/pci.h header so they don't clutter
the driver interface.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/virtualization:
PCI: Document reset method return values
PCI: Detach driver before procfs & sysfs teardown on device remove
PCI: Apply Cavium ThunderX ACS quirk to more Root Ports
PCI: Set Cavium ACS capability quirk flags to assert RR/CR/SV/UF
PCI: Restore ARI Capable Hierarchy before setting numVFs
PCI: Create SR-IOV virtfn/physfn links before attaching driver
PCI: Expose SR-IOV offset, stride, and VF device ID via sysfs
PCI: Cache the VF device ID in the SR-IOV structure
PCI: Add Kconfig PCI_IOV dependency for PCI_REALLOC_ENABLE_AUTO
PCI: Remove unused function __pci_reset_function()
PCI: Remove reset argument from pci_iov_{add,remove}_virtfn()
* pci/resource:
PCI: Fail pci_map_rom() if the option ROM is invalid
PCI: Move pci_map_rom() error path
x86/PCI: Enable a 64bit BAR on AMD Family 15h (Models 00-1f, 30-3f, 60-7f)
PCI: Add pci_resize_resource() for resizing BARs
PCI: Add resizable BAR infrastructure
PCI: Add PCI resource type mask #define
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add resizable BAR infrastructure, including defines and helper functions to
read the possible sizes of a BAR and update its size. See PCIe r3.1, sec
7.22.
Link: https://pcisig.com/sites/default/files/specification_documents/ECN_Resizable-BAR_24Apr2008.pdf
Signed-off-by: Christian König <christian.koenig@amd.com>
[bhelgaas: rename to functions with "rebar" (to match #defines), drop shift
#defines, drop "_MASK" suffixes, fix typos, fix kerneldoc]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cache the VF device ID in the SR-IOV structure and use it instead of
reading it over and over from the PF config space capability.
Signed-off-by: Filippo Sironi <sironi@amazon.de>
[bhelgaas: rename to "vf_device" to match pci_dev->device]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Make this const as it not modified in the file referencing it. It is only
stored in a const field 'type' of a device structure. Also, add const to
the variable declaration in the header file.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Per PCIe r3.1, sec 2.2.6.2 and 7.8.4, a Requester may not use 8-bit Tags
unless its Extended Tag Field Enable is set, but all Receivers/Completers
must handle 8-bit Tags correctly regardless of their Extended Tag Field
Enable.
Some devices do not handle 8-bit Tags as Completers, so add a quirk for
them. If we find such a device, we disable Extended Tags for the entire
hierarchy to make peer-to-peer DMA possible.
The Broadcom HT2100 seems to have issues with handling 8-bit tags. Mark it
as broken.
The pci_walk_bus() in the quirk handles devices we've enumerated in the
past, and pci_configure_device() handles devices we enumerate in the
future.
Fixes: 60db3a4d8c ("PCI: Enable PCIe Extended Tags if supported")
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1467674
Reported-and-tested-by: Wim ten Have <wim.ten.have@oracle.com>
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
[bhelgaas: changelog, tweak messages, rename bit and quirk]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit dc15e71eef (PCI / PM: Restore PME Enable if skipping wakeup
setup) introduced a mechanism by which the PME Enable bit can be
restored by pci_enable_wake() if dev->wakeup_prepared is set in
case it has been overwritten by PCI config space restoration.
However, that commit overlooked the fact that on some systems (Dell
XPS13 9360 in particular) the AML handling wakeup events checks PME
Status and PME Enable and it won't trigger a Notify() for devices
where those bits are not set while it is running.
That happens during resume from suspend-to-idle when pci_restore_state()
invoked by pci_pm_default_resume_early() clears PME Enable before the
wakeup events are processed by AML, effectively causing those wakeup
events to be ignored.
Fix this issue by restoring the PME Enable configuration right after
pci_restore_state() has been called instead of doing that in
pci_enable_wake().
Fixes: dc15e71eef (PCI / PM: Restore PME Enable if skipping wakeup setup)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
After previous changes it is not necessary to distinguish between
device wakeup for run time and device wakeup from system sleep states
any more, so rework the PCI device wakeup settings code accordingly.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Every method in struct device_driver or structures derived from it like
struct pci_driver MUST provide exclusion vs the driver's ->remove() method,
usually by using device_lock().
Protect use of pci_driver->sriov_configure() by holding the device lock
while calling it.
The PCI core sets the pci_dev->driver pointer in local_pci_probe() before
calling ->probe() and only clears it after ->remove(). This means driver's
->sriov_configure() callback will happily race with probe() and remove(),
most likely leading to BUGs, since drivers don't expect this.
Remove the iov lock completely, since we remove the last user.
[bhelgaas: changelog, thanks to Christoph for locking rule]
Link: http://lkml.kernel.org/r/20170522225023.14010-1-jakub.kicinski@netronome.com
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJZEHmsAAoJEFmIoMA60/r88SgQAJbFddueb0+DfJ+USDud4b/Z
akfS+G1UAm+TgtMyh1wM49dHzFssp36uWJxtWI+bPqBzuy94PMCbz7JVUV28gX9G
tFhFuc5YH94I/3y85rbZnolb6uZN9MhLjzTFqDC9ilW6HFqmwK4t4wlHSCjQN1St
svLYvs2G6n6/VK3Fre7/wOvdZ1erG4Qod+kn5Tx3K5TQydmRlaSBfK+DRANuDBkM
KzGO7Bkc/Cx8hb9pHmaey/wxmNrrgmVjTtWrEnb2tEq833zP4h6GhUIJEKodMSi5
gXPNZgKlu3n5L592M0UCh4EoHejzkv9wrcsoDm+djmsc5Zg2Howq4kAdHP8k4hUG
0gt8n0ni9vhJN56jikrGi7cAdHCKSNnx2Ue/qTCbX0ncB3XUMuJxJwCsgW/6wa9f
oU7tRtTS03UltnKoFAcyYclS4TaSY4SA4ySaK6Hi+cRkdVFDdyHQYbHHNSU7MsA+
IS2tXvGoIdSYyrZMHSRcl2rRTfYQUkmPEvBF3LvqZr32M4mJMmUNAPLZaly373ZE
iwq0ZJlrLeM0cqdFIG3S60RtJyQk/HBN1NMqrYHArWOxvWIgNd5F8NCsTTxY3wU3
IxgBIuUFcbVwVkqEHGs8K5AvB3oghqdnA3eGOV79799eMtLn3LOvyIlpHMSw9WUq
ags00JtMLitfNPBH3eSl
=eE4D
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- add framework for supporting PCIe devices in Endpoint mode (Kishon
Vijay Abraham I)
- use non-postable PCI config space mappings when possible (Lorenzo
Pieralisi)
- clean up and unify mmap of PCI BARs (David Woodhouse)
- export and unify Function Level Reset support (Christoph Hellwig)
- avoid FLR for Intel 82579 NICs (Sasha Neftin)
- add pci_request_irq() and pci_free_irq() helpers (Christoph Hellwig)
- short-circuit config access failures for disconnected devices (Keith
Busch)
- remove D3 sleep delay when possible (Adrian Hunter)
- freeze PME scan before suspending devices (Lukas Wunner)
- stop disabling MSI/MSI-X in pci_device_shutdown() (Prarit Bhargava)
- disable boot interrupt quirk for ASUS M2N-LR (Stefan Assmann)
- add arch-specific alignment control to improve device passthrough by
avoiding multiple BARs in a page (Yongji Xie)
- add sysfs sriov_drivers_autoprobe to control VF driver binding
(Bodong Wang)
- allow slots below PCI-to-PCIe "reverse bridges" (Bjorn Helgaas)
- fix crashes when unbinding host controllers that don't support
removal (Brian Norris)
- add driver for MicroSemi Switchtec management interface (Logan
Gunthorpe)
- add driver for Faraday Technology FTPCI100 host bridge (Linus
Walleij)
- add i.MX7D support (Andrey Smirnov)
- use generic MSI support for Aardvark (Thomas Petazzoni)
- make Rockchip driver modular (Brian Norris)
- advertise 128-byte Read Completion Boundary support for Rockchip
(Shawn Lin)
- advertise PCI_EXP_LNKSTA_SLC for Rockchip root port (Shawn Lin)
- convert atomic_t to refcount_t in HV driver (Elena Reshetova)
- add CPU IRQ affinity in HV driver (K. Y. Srinivasan)
- fix PCI bus removal in HV driver (Long Li)
- add support for ThunderX2 DMA alias topology (Jayachandran C)
- add ThunderX pass2.x 2nd node MCFG quirk (Tomasz Nowicki)
- add ITE 8893 bridge DMA alias quirk (Jarod Wilson)
- restrict Cavium ACS quirk only to CN81xx/CN83xx/CN88xx devices
(Manish Jaggi)
* tag 'pci-v4.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (146 commits)
PCI: Don't allow unbinding host controllers that aren't prepared
ARM: DRA7: clockdomain: Change the CLKTRCTRL of CM_PCIE_CLKSTCTRL to SW_WKUP
MAINTAINERS: Add PCI Endpoint maintainer
Documentation: PCI: Add userguide for PCI endpoint test function
tools: PCI: Add sample test script to invoke pcitest
tools: PCI: Add a userspace tool to test PCI endpoint
Documentation: misc-devices: Add Documentation for pci-endpoint-test driver
misc: Add host side PCI driver for PCI test function device
PCI: Add device IDs for DRA74x and DRA72x
dt-bindings: PCI: dra7xx: Add DT bindings to enable unaligned access
PCI: dwc: dra7xx: Workaround for errata id i870
dt-bindings: PCI: dra7xx: Add DT bindings for PCI dra7xx EP mode
PCI: dwc: dra7xx: Add EP mode support
PCI: dwc: dra7xx: Facilitate wrapper and MSI interrupts to be enabled independently
dt-bindings: PCI: Add DT bindings for PCI designware EP mode
PCI: dwc: designware: Add EP mode support
Documentation: PCI: Add binding documentation for pci-test endpoint function
ixgbe: Use pcie_flr() instead of duplicating it
IB/hfi1: Use pcie_flr() instead of duplicating it
PCI: imx6: Fix spelling mistake: "contol" -> "control"
...
* pci/virtualization:
ixgbe: Use pcie_flr() instead of duplicating it
IB/hfi1: Use pcie_flr() instead of duplicating it
PCI: Call pcie_flr() from reset_chelsio_generic_dev()
PCI: Call pcie_flr() from reset_intel_82599_sfp_virtfn()
PCI: Export pcie_flr()
PCI: Add sysfs sriov_drivers_autoprobe to control VF driver binding
PCI: Avoid FLR for Intel 82579 NICs
Conflicts:
include/linux/pci.h
* pci/resource-mmap:
ia64: Use generic pci_mmap_resource_range()
ia64: Remove redundant checks for WC in pci_mmap_page_range()
ia64: Remove redundant valid_mmap_phys_addr_range() from pci_mmap_page_range()
PCI: Add I/O BAR support to generic pci_mmap_resource_range()
x86/PCI: Use generic pci_mmap_resource_range()
unicore32/PCI: Use generic pci_mmap_resource_range()
sh/PCI: Use generic pci_mmap_resource_range()
parisc: Use generic pci_mmap_resource_range()
mn10300/PCI: Use generic pci_mmap_resource_range()
MIPS: PCI: Use generic pci_mmap_resource_range()
cris/PCI: Use generic pci_mmap_resource_range()
ARM/PCI: Use generic pci_mmap_resource_range()
PCI: Add pci_mmap_resource_range() and use it for ARM64
PCI: Add BAR index argument to pci_mmap_page_range()
PCI: Use BAR index in sysfs attr->private instead of resource pointer
PCI: Add arch_can_pci_mmap_io() on architectures which can mmap() I/O space
PCI: Move multiple declarations of pci_mmap_page_range() to <linux/pci.h>
PCI: Add arch_can_pci_mmap_wc() macro
xtensa/PCI: Do not mmap PCI BARs to userspace as write-through
PCI: Only allow WC mmap on prefetchable resources
PCI: Fix another sanity check bug in /proc/pci mmap
PCI: Fix pci_mmap_fits() for HAVE_PCI_RESOURCE_TO_USER platforms
Sometimes it is not desirable to bind SR-IOV VFs to drivers. This can save
host side resource usage by VF instances that will be assigned to VMs.
Add a new PCI sysfs interface "sriov_drivers_autoprobe" to control that
from the PF. To modify it, echo 0/n/N (disable probe) or 1/y/Y (enable
probe) to:
/sys/bus/pci/devices/<DOMAIN:BUS:DEVICE.FUNCTION>/sriov_drivers_autoprobe
Note that this must be done before enabling VFs. The change will not take
effect if VFs are already enabled. Simply, one can disable VFs by setting
sriov_numvfs to 0, choose whether to probe or not, and then re-enable the
VFs by restoring sriov_numvfs.
[bhelgaas: changelog, ABI doc]
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Starting to leave behind the legacy of the pci_mmap_page_range() interface
which takes "user-visible" BAR addresses. This takes just the resource and
offset.
For now, both APIs coexist and depending on the platform, one is
implemented as a wrapper around the other.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Detect on probe whether a PCI device is part of a Thunderbolt controller.
Intel uses a Vendor-Specific Extended Capability (VSEC) with ID 0x1234
on such devices. Detect presence of this VSEC and cache it in a newly
added is_thunderbolt bit in struct pci_dev.
Also, add a helper to check whether a given PCI device is situated on a
Thunderbolt daisy chain (i.e., below a PCI device with is_thunderbolt
set).
The necessity arises from the following:
* If an external Thunderbolt GPU is connected to a dual GPU laptop,
that GPU is currently registered with vga_switcheroo even though it
can neither drive the laptop's panel nor be powered off by the
platform. To vga_switcheroo it will appear as if two discrete
GPUs are present. As a result, when the external GPU is runtime
suspended, vga_switcheroo will cut power to the internal discrete GPU
which may not be runtime suspended at all at this moment. The
solution is to not register external GPUs with vga_switcheroo, which
necessitates a way to recognize if they're on a Thunderbolt daisy
chain.
* Dual GPU MacBook Pros introduced 2011+ can no longer switch external
DisplayPort ports between GPUs. (They're no longer just used for DP
but have become combined DP/Thunderbolt ports.) The driver to switch
the ports, drivers/platform/x86/apple-gmux.c, needs to detect presence
of a Thunderbolt controller and, if found, keep external ports
permanently switched to the discrete GPU.
v2: Make kerneldoc for pci_is_thunderbolt_attached() more precise,
drop portion of commit message pertaining to separate series.
(Bjorn Helgaas)
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Michael Jamet <michael.jamet@intel.com>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Cc: Amir Levy <amir.jer.levy@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: http://patchwork.freedesktop.org/patch/msgid/0ab165a4a35c0b60f29d4c306c653ead14fcd8f9.1489145162.git.lukas@wunner.de
Add a new state to pci_dev to be set when it is unexpectedly disconnected.
The PCI driver tear down functions can observe this new device state so
they may skip operations that will fail.
The pciehp and pcie-dpc drivers are aware when the link is down, so these
set the flag when their handlers detect the device is disconnected.
Tested-by: Krishna Dhulipala <krishnad@fb.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Wei Zhang <wzhang@fb.com>
* pci/virtualization:
PCI: Add comments about ROM BAR updating
PCI: Decouple IORESOURCE_ROM_ENABLE and PCI_ROM_ADDRESS_ENABLE
PCI: Remove pci_resource_bar() and pci_iov_resource_bar()
PCI: Don't update VF BARs while VF memory space is enabled
PCI: Separate VF BAR updates from standard BAR updates
PCI: Update BARs using property bits appropriate for type
PCI: Ignore BAR updates on virtual functions
PCI: Do any VF BAR updates before enabling the BARs
PCI: Support INTx masking on ConnectX-4 with firmware x.14.1100+
PCI: Convert Mellanox broken INTx quirks to be for listed devices only
PCI: Convert broken INTx masking quirks from HEADER to FINAL
net/mlx4_core: Use device ID defines
PCI: Add Mellanox device IDs
* pci/pm:
x86/platform/intel-mid: Constify mid_pci_platform_pm
PCI: pciehp: Add runtime PM support for PCIe hotplug ports
ACPI / hotplug / PCI: Make device_is_managed_by_native_pciehp() public
ACPI / hotplug / PCI: Use cached copy of PCI_EXP_SLTCAP_HPC bit
PCI: Unfold conditions to block runtime PM on PCIe ports
PCI: Consolidate conditions to allow runtime PM on PCIe ports
PCI: Activate runtime PM on a PCIe port only if it can suspend
PCI: Speed up algorithm in pci_bridge_d3_update()
PCI: Autosense device removal in pci_bridge_d3_update()
PCI: Don't acquire ref on parent in pci_bridge_d3_update()
USB: UHCI: report non-PME wakeup signalling for Intel hardware
PCI: Check for PME in targeted sleep state
Move PCI configuration space size macros (PCI_CFG_SPACE_SIZE and
PCI_CFG_SPACE_EXP_SIZE) from drivers/pci/pci.h to
include/uapi/linux/pci_regs.h so they can be used by more drivers and
eliminate duplicate definitions.
[bhelgaas: Expand comment to include PCI-X details]
Signed-off-by: Wang Sheng-Hui <shhuiw@foxmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The acpi_get_rc_resources() is used to get the RC register address that can
not be described in MCFG. It takes the _HID & segment to look for and
outputs the RC address resource. Use PNP0C02 devices to describe such RC
address resource. Use _UID to match segment to tell which root bus the
PNP0C02 resource belongs to.
[bhelgaas: add dev argument, wrap in #ifdef CONFIG_PCI_QUIRKS]
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_std_update_resource() only deals with standard BARs, so we don't have
to worry about the complications of VF BARs in an SR-IOV capability.
Compute the BAR address inline and remove pci_resource_bar(). That makes
pci_iov_resource_bar() unused, so remove that as well.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Previously pci_update_resource() used the same code path for updating
standard BARs and VF BARs in SR-IOV capabilities.
Split the VF BAR update into a new pci_iov_update_resource() internal
interface, which makes it simpler to compute the BAR address (we can get
rid of pci_resource_bar() and pci_iov_resource_bar()).
This patch:
- Renames pci_update_resource() to pci_std_update_resource(),
- Adds pci_iov_update_resource(),
- Makes pci_update_resource() a wrapper that calls the appropriate one,
No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Currently pcie_portdrv_probe() activates runtime PM on a PCIe port even
if it will never actually suspend because the BIOS is too old or the
"pcie_port_pm=off" option was specified on the kernel command line.
A few CPU cycles can be saved by not activating runtime PM at all in these
cases, because rpm_idle() and rpm_suspend() will bail out right at the
beginning when calling rpm_check_suspend_allowed(), instead of carrying out
various locking and assignments, invoking rpm_callback(), getting back
-EBUSY and rolling everything back.
The conditions checked in pci_bridge_d3_possible() are all static, they
never change during uptime of the system, hence it's safe to call this to
determine if runtime PM should be activated.
No functional change intended.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The algorithm to update the flag indicating whether a bridge may go to D3
makes a few optimizations based on whether the update was caused by the
removal of a device on the one hand, versus the addition of a device or the
change of its D3cold flags on the other hand.
The information whether the update pertains to a removal is currently
passed in by the caller, but the function may as well determine that itself
by examining the device in question, thereby allowing for a considerable
simplification and reduction of the code.
Out of several options to determine removal, I've chosen the function
device_is_registered() because it's cheap: It merely returns the
dev->kobj.state_in_sysfs flag. That flag is set through device_add() when
the root bus is scanned and cleared through device_remove(). The call to
pci_bridge_d3_update() happens after each of these calls, respectively, so
the ordering is correct.
No functional change intended.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pci/pm:
PCI: Avoid unnecessary resume after direct-complete
PCI: Recognize D3cold in pci_update_current_state()
PCI: Query platform firmware for device power state
PCI: Afford direct-complete to devices with non-standard PM
Usually the most accurate way to determine a PCI device's power state is to
read its PM Control & Status Register. There are two cases however when
this is not an option: If the device doesn't have the PM capability at
all, or if it is in D3cold (in which case its config space is
inaccessible).
In both cases, we can alternatively query the platform firmware for its
opinion on the device's power state. To facilitate this, augment struct
pci_platform_pm_ops with a ->get_power callback and implement it for
acpi_pci_platform_pm (the only pci_platform_pm_ops existing so far).
It is used by a forthcoming commit to let pci_update_current_state()
recognize D3cold.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add Precision Time Measurement (PTM) support (see PCIe r3.1, sec 6.22).
Enable PTM on PTM Root devices and switch ports. This does not enable PTM
on endpoints.
There currently are no PTM-capable devices on the market, but it is
expected to be supported by the Intel Apollo Lake platform.
[bhelgaas: complete rework]
Signed-off-by: Jonathan Yong <jonathan.yong@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Currently the Linux PCI core does not touch power state of PCI bridges and
PCIe ports when system suspend is entered. Leaving them in D0 consumes
power unnecessarily and may prevent the CPU from entering deeper C-states.
With recent PCIe hardware we can power down the ports to save power given
that we take into account few restrictions:
- The PCIe port hardware is recent enough, starting from 2015.
- Devices connected to PCIe ports are effectively in D3cold once the port
is transitioned to D3 (the config space is not accessible anymore and
the link may be powered down).
- Devices behind the PCIe port need to be allowed to transition to D3cold
and back. There is a way both drivers and userspace can forbid this.
- If the device behind the PCIe port is capable of waking the system it
needs to be able to do so from D3cold.
This patch adds a new flag to struct pci_device called 'bridge_d3'. This
flag is set and cleared by the PCI core whenever there is a change in power
management state of any of the devices behind the PCIe port. When system
later on is suspended we only need to check this flag and if it is true
transition the port to D3 otherwise we leave it in D0.
Also provide override mechanism via command line parameter
"pcie_port_pm=[off|force]" that can be used to disable or enable the
feature regardless of the BIOS manufacturing date.
Tested-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After 104daa71b3 ("PCI: Determine actual VPD size on first access"), the
PCI core computes the valid VPD size by parsing the VPD starting at offset
0x0. We don't attempt to read past that valid size because that causes
some devices to crash.
However, some devices do have data past that valid size. For example,
Chelsio adapters contain two VPD structures, and the driver needs both of
them.
Add pci_set_vpd_size(). If a driver knows it is safe to read past the end
of the VPD data structure at offset 0, it can use pci_set_vpd_size() to
allow access to as much data as it needs.
[bhelgaas: changelog, split patches, rename to pci_set_vpd_size() and
return int (not ssize_t)]
Fixes: 104daa71b3 ("PCI: Determine actual VPD size on first access")
Tested-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We only support one flavor of VPD, so there's no need to complicate things
by having a "generic" struct pci_vpd and a more specific struct
pci_vpd_pci22.
Fold struct pci_vpd_pci22 directly into struct pci_vpd.
[bhelgaas: remove NULL check before kfree of dev->vpd (per kfreeaddr.cocci)]
Tested-by: Shane Seymour <shane.seymour@hpe.com>
Tested-by: Babu Moger <babu.moger@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
There's only one kind of VPD, so we don't need to qualify it as "the
version described by PCI spec rev 2.2."
Rename the following symbols to remove unnecessary "pci22":
PCI_VPD_PCI22_SIZE -> PCI_VPD_MAX_SIZE
pci_vpd_pci22_size() -> pci_vpd_size()
pci_vpd_pci22_wait() -> pci_vpd_wait()
pci_vpd_pci22_read() -> pci_vpd_read()
pci_vpd_pci22_write() -> pci_vpd_write()
pci_vpd_pci22_ops -> pci_vpd_ops
pci_vpd_pci22_init() -> pci_vpd_init()
Tested-by: Shane Seymour <shane.seymour@hpe.com>
Tested-by: Babu Moger <babu.moger@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
The struct pci_vpd_ops.release function pointer is always
pci_vpd_pci22_release(), so there's no need for the flexibility of a
function pointer.
Inline the pci_vpd_pci22_release() body into pci_vpd_release() and remove
pci_vpd_pci22_release() and the struct pci_vpd_ops.release function
pointer.
Tested-by: Shane Seymour <shane.seymour@hpe.com>
Tested-by: Babu Moger <babu.moger@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Move pci_vpd_release() so it's next to the other VPD functions. This puts
it next to pci_vpd_pci22_init(), which allocates the space freed by
pci_vpd_release().
Tested-by: Shane Seymour <shane.seymour@hpe.com>
Tested-by: Babu Moger <babu.moger@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
The pci_platform_pm_ops structure is never modified, so declare it as
const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
4a7cc83167 ("genirq/MSI: Move msi_list from struct pci_dev to struct
device") removed the contents of pci_msi_init_pci_dev(). All
implementation of it are now empty, so remove it completely.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit b3a72384fe ("ARM/PCI: Replace pci_sys_data->align_resource with
global function pointer") introduced an ARM-specific align_resource()
function pointer. This is not portable to other arches and doesn't work
for platforms with two different PCIe host bridge controllers.
Move the function pointer to the pci_host_bridge structure so each host
bridge driver can specify its own align_resource() function.
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Add support for devices using Enhanced Allocation entries instead of BARs.
This allows the kernel to parse the EA Extended Capability structure in PCI
config space and claim the BAR-equivalent resources.
See https://pcisig.com/sites/default/files/specification_documents/ECN_Enhanced_Allocation_23_Oct_2014_Final.pdf
[bhelgaas: add spec URL, s/pci_ea_set_flags/pci_ea_flags/, consolidate
declarations, print unknown property in hex to match spec]
Signed-off-by: Sean O. Stalley <sean.stalley@intel.com>
[david.daney@cavium.com: Add more support/checking for Entry Properties,
allow EA behind bridges, rewrite some error messages.]
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit bac2a909a0 (PCI / PM: Avoid resuming PCI devices during
system suspend) introduced a mechanism by which some PCI devices that
were runtime-suspended at the system suspend time might be left in
that state for the duration of the system suspend-resume cycle.
However, it overlooked devices that were marked as capable of waking
up the system just because PME support was detected in their PCI
config space.
Namely, in that case, device_can_wakeup(dev) returns 'true' for the
device and if the device is not configured for system wakeup,
device_may_wakeup(dev) returns 'false' and it will be resumed during
system suspend even though configuring it for system wakeup may not
really make sense at all.
To avoid this problem, simply disable PME for PCI devices that have
not been configured for system wakeup and are runtime-suspended at
the system suspend time for the duration of the suspend-resume cycle.
If the device is in D3cold, its config space is not available and it
shouldn't be written to, but that's only possible if the device
has platform PM support and the platform code is responsible for
checking whether or not the device's configuration is suitable for
system suspend in that case.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some quirks search for a HyperTransport capability and use a hard-coded TTL
value of 48 to avoid an infinite loop.
Move the definition of PCI_FIND_CAP_TTL to pci.h and use it instead of the
hard-coded TTL values.
[bhelgaas: changelog]
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_ari_enabled() is useful outside of drivers/pci, particularly for
deriving INTx routing via ACPI _PRT, so move it to the global header.
Also convert to bool return.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Don Dutile <ddutile@redhat.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Move pci_msi_set_enable() and pci_msix_clear_and_set_ctrl() to
drivers/pci/pci.h so they're available even when MSI isn't configured
into the kernel.
No functional change.
[bhelgaas: changelog, split into separate patch]
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
- Numerous minor fixes, cleanups etc.
- More EEH work from Gavin to remove its dependency on device_nodes.
- Memory hotplug implemented entirely in the kernel from Nathan Fontenot.
- Removal of redundant CONFIG_PPC_OF by Kevin Hao.
- Rewrite of VPHN parsing logic & tests from Greg Kurz.
- A fix from Nish Aravamudan to reduce memory usage by clamping
nodes_possible_map.
- Support for pstore on powernv from Hari Bathini.
- Removal of old powerpc specific byte swap routines by David Gibson.
- Fix from Vasant Hegde to prevent the flash driver telling you it was flashing
your firmware when it wasn't.
- Patch from Ben Herrenschmidt to add an OPAL heartbeat driver.
- Fix for an oops causing get/put_cpu_var() imbalance in perf by Jan Stancek.
- Some fixes for migration from Tyrel Datwyler.
- A new syscall to switch the cpu endian by Michael Ellerman.
- Large series from Wei Yang to implement SRIOV, reviewed and acked by Bjorn.
- A fix for the OPAL sensor driver from Cédric Le Goater.
- Fixes to get STRICT_MM_TYPECHECKS building again by Michael Ellerman.
- Large series from Daniel Axtens to make our PCI hooks per PHB rather than per
machine.
- Small patch from Sam Bobroff to explicitly abort non-suspended transactions
on syscalls, plus a test to exercise it.
- Numerous reworks and fixes for the 24x7 PMU from Sukadev Bhattiprolu.
- Small patch to enable the hard lockup detector from Anton Blanchard.
- Fix from Dave Olson for missing L2 cache information on some CPUs.
- Some fixes from Michael Ellerman to get Cell machines booting again.
- Freescale updates from Scott: Highlights include BMan device tree nodes, an
MSI erratum workaround, a couple minor performance improvements, config
updates, and misc fixes/cleanup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=03Yh
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc updates from Michael Ellerman:
- Numerous minor fixes, cleanups etc.
- More EEH work from Gavin to remove its dependency on device_nodes.
- Memory hotplug implemented entirely in the kernel from Nathan
Fontenot.
- Removal of redundant CONFIG_PPC_OF by Kevin Hao.
- Rewrite of VPHN parsing logic & tests from Greg Kurz.
- A fix from Nish Aravamudan to reduce memory usage by clamping
nodes_possible_map.
- Support for pstore on powernv from Hari Bathini.
- Removal of old powerpc specific byte swap routines by David Gibson.
- Fix from Vasant Hegde to prevent the flash driver telling you it was
flashing your firmware when it wasn't.
- Patch from Ben Herrenschmidt to add an OPAL heartbeat driver.
- Fix for an oops causing get/put_cpu_var() imbalance in perf by Jan
Stancek.
- Some fixes for migration from Tyrel Datwyler.
- A new syscall to switch the cpu endian by Michael Ellerman.
- Large series from Wei Yang to implement SRIOV, reviewed and acked by
Bjorn.
- A fix for the OPAL sensor driver from Cédric Le Goater.
- Fixes to get STRICT_MM_TYPECHECKS building again by Michael Ellerman.
- Large series from Daniel Axtens to make our PCI hooks per PHB rather
than per machine.
- Small patch from Sam Bobroff to explicitly abort non-suspended
transactions on syscalls, plus a test to exercise it.
- Numerous reworks and fixes for the 24x7 PMU from Sukadev Bhattiprolu.
- Small patch to enable the hard lockup detector from Anton Blanchard.
- Fix from Dave Olson for missing L2 cache information on some CPUs.
- Some fixes from Michael Ellerman to get Cell machines booting again.
- Freescale updates from Scott: Highlights include BMan device tree
nodes, an MSI erratum workaround, a couple minor performance
improvements, config updates, and misc fixes/cleanup.
* tag 'powerpc-4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (196 commits)
powerpc/powermac: Fix build error seen with powermac smp builds
powerpc/pseries: Fix compile of memory hotplug without CONFIG_MEMORY_HOTREMOVE
powerpc: Remove PPC32 code from pseries specific find_and_init_phbs()
powerpc/cell: Fix iommu breakage caused by controller_ops change
powerpc/eeh: Fix crash in eeh_add_device_early() on Cell
powerpc/perf: Cap 64bit userspace backtraces to PERF_MAX_STACK_DEPTH
powerpc/perf/hv-24x7: Fail 24x7 initcall if create_events_from_catalog() fails
powerpc/pseries: Correct memory hotplug locking
powerpc: Fix missing L2 cache size in /sys/devices/system/cpu
powerpc: Add ppc64 hard lockup detector support
oprofile: Disable oprofile NMI timer on ppc64
powerpc/perf/hv-24x7: Add missing put_cpu_var()
powerpc/perf/hv-24x7: Break up single_24x7_request
powerpc/perf/hv-24x7: Define update_event_count()
powerpc/perf/hv-24x7: Whitespace cleanup
powerpc/perf/hv-24x7: Define add_event_to_24x7_request()
powerpc/perf/hv-24x7: Rename hv_24x7_event_update
powerpc/perf/hv-24x7: Move debug prints to separate function
powerpc/perf/hv-24x7: Drop event_24x7_request()
powerpc/perf/hv-24x7: Use pr_devel() to log message
...
Conflicts:
tools/testing/selftests/powerpc/Makefile
tools/testing/selftests/powerpc/tm/Makefile
The find_pci_host_bridge() function can be useful to other PCI code so
export it. Change its name to pci_find_host_bridge().
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
An SR-IOV device can change its First VF Offset and VF Stride based on the
values of ARI Capable Hierarchy and NumVFs. The number of buses required
for all VFs is determined by NumVFs, First VF Offset, and VF Stride (see
SR-IOV spec r1.1, sec 2.1.2).
Previously pci_iov_bus_range() computed how many buses would be required by
TotalVFs, but this was based on a single NumVFs value and may not have been
the maximum for all NumVFs configurations.
Iterate over all valid NumVFs and calculate the maximum number of bus
numbers that could ever be required for VFs of this device.
[bhelgaas: changelog, compute busnr of NumVFs, not TotalVFs, remove
kerenl-doc comment marker]
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently we don't store the individual VF BAR size. We calculate it when
needed by dividing the PF's IOV resource size (which contains space for
*all* the VFs) by total_VFs or by reading the BAR in the SR-IOV capability
again.
Keep the individual VF BAR size in struct pci_sriov.barsz[], add
pci_iov_resource_size() to retrieve it, and use that instead of doing the
division or reading the SR-IOV capability BAR.
[bhelgaas: rename to "barsz[]", simplify barsz[] index computation, remove
SR-IOV capability BAR sizing]
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit f25c0ae2b4 (ACPI / PM: Avoid resuming devices in ACPI PM
domain during system suspend) modified the ACPI PM domain's system
suspend callbacks to allow devices attached to it to be left in the
runtime-suspended state during system suspend so as to optimize
the suspend process.
This was based on the general mechanism introduced by commit
aae4518b31 (PM / sleep: Mechanism to avoid resuming runtime-suspended
devices unnecessarily).
Extend that approach to PCI devices by modifying the PCI bus type's
->prepare callback to return 1 for devices that are runtime-suspended
when it is being executed and that are in a suitable power state and
need not be resumed going forward.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Add pci_bus_clip_resource(). If a PCI-PCI bridge window overlaps an
upstream bridge window but is not completely contained by it, this clips
the downstream window so it fits inside the upstream one.
No functional change (this adds the function but no callers).
[bhelgaas: changelog, split into separate patch]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=85491
Reported-by: Marek Kordik <kordikmarek@gmail.com>
Fixes: 5b28541552 ("PCI: Restrict 64-bit prefetchable bridge windows to 64-bit resources")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.16+
pci_iov_resource_bar() always sets its 'pci_bar_type' parameter to
'pci_bar_unknown'. Drop the parameter and just use 'pci_bar_unknown'
directly in the callers.
No functional change intended.
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Chris Wright <chrisw@sous-sol.org>
CC: Yu Zhao <yuzhao@google.com>
Previously we applied _HPX type 2 record Link Control register settings
only to bridges with a subordinate bus. But it's better to apply them to
all devices with a link because if the subordinate bus has not been
allocated yet, we won't apply settings to the device.
Use pcie_cap_has_lnkctl() to determine whether the device has a Link
Control register instead of looking at dev->subordinate.
[bhelgaas: changelog]
Fixes: 6cd33649fa ("PCI: Add pci_configure_device() during enumeration")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/hotplug:
PCI: cpqphp: Fix possible null pointer dereference
NVMe: Implement PCIe reset notification callback
PCI: Notify driver before and after device reset
* pci/pci_is_bridge:
pcmcia: Use pci_is_bridge() to simplify code
PCI: pciehp: Use pci_is_bridge() to simplify code
PCI: acpiphp: Use pci_is_bridge() to simplify code
PCI: cpcihp: Use pci_is_bridge() to simplify code
PCI: shpchp: Use pci_is_bridge() to simplify code
PCI: rpaphp: Use pci_is_bridge() to simplify code
sparc/PCI: Use pci_is_bridge() to simplify code
powerpc/PCI: Use pci_is_bridge() to simplify code
ia64/PCI: Use pci_is_bridge() to simplify code
x86/PCI: Use pci_is_bridge() to simplify code
PCI: Use pci_is_bridge() to simplify code
PCI: Add new pci_is_bridge() interface
PCI: Rename pci_is_bridge() to pci_has_subordinate()
* pci/virtualization:
PCI: Introduce new device binding path using pci_dev.driver_override
Conflicts:
drivers/pci/pci-sysfs.c
Previously, pci_is_bridge() returned true only when a subordinate bus
existed. Rename pci_is_bridge() to pci_has_subordinate() to better
indicate what we're checking.
No functional change.
[bhelgaas: changelog]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Some PCI functions used to be marked __devinit. When CONFIG_HOTPLUG was
not set, these functions were discarded after boot. A few callers of these
__devinit functions were marked __ref to indicate that they could safely
call the __devinit functions even though the callers were not __devinit.
But CONFIG_HOTPLUG and __devinit are now gone, and the need for the __ref
annotations is also gone, so remove them. Relevant historical commits:
54b956b903 Remove __dev* markings from init.h
a8e4b9c101 PCI: add generic pci_hp_add_bridge()
0ab2b57f8d PCI: fix section mismatch warning in pci_scan_child_bus
451124a7cc PCI: fix 4x section mismatch warnings
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This reverts commit 74bb1bcc7d ("PCI: handle SR-IOV Virtual Function
Migration"), removing this exported interface:
pci_sriov_migration()
Since pci_sriov_migration() is unused, it is impossible to schedule
sriov_migration_task() or use any of the other migration infrastructure.
This is based on Stephen Hemminger's patch (see link below), but goes a bit
further.
Link: http://lkml.kernel.org/r/20131227132710.7190647c@nehalam.linuxnetplumber.net
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Stephen Hemminger <stephen@networkplumber.org>
Using 'make namespacecheck' identify code which should be declared static.
Checked for users in other driver/archs as well. Compile tested only.
This stops exporting the following interfaces to modules:
pci_target_state()
pci_load_saved_state()
[bhelgaas: retained pci_find_next_ext_capability() and pci_cfg_space_size()]
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The dev_attrs field of struct bus_type is going away soon, dev_groups
should be used instead. This converts the PCI bus code to use the
correct field.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The bus_attrs field of struct bus_type is going away soon, dev_groups
should be used instead. This converts the PCI bus code to use the
correct field.
Cc: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull networking changes from David Miller:
"Noteworthy changes this time around:
1) Multicast rejoin support for team driver, from Jiri Pirko.
2) Centralize and simplify TCP RTT measurement handling in order to
reduce the impact of bad RTO seeding from SYN/ACKs. Also, when
both timestamps and local RTT measurements are available prefer
the later because there are broken middleware devices which
scramble the timestamp.
From Yuchung Cheng.
3) Add TCP_NOTSENT_LOWAT socket option to limit the amount of kernel
memory consumed to queue up unsend user data. From Eric Dumazet.
4) Add a "physical port ID" abstraction for network devices, from
Jiri Pirko.
5) Add a "suppress" operation to influence fib_rules lookups, from
Stefan Tomanek.
6) Add a networking development FAQ, from Paul Gortmaker.
7) Extend the information provided by tcp_probe and add ipv6 support,
from Daniel Borkmann.
8) Use RCU locking more extensively in openvswitch data paths, from
Pravin B Shelar.
9) Add SCTP support to openvswitch, from Joe Stringer.
10) Add EF10 chip support to SFC driver, from Ben Hutchings.
11) Add new SYNPROXY netfilter target, from Patrick McHardy.
12) Compute a rate approximation for sending in TCP sockets, and use
this to more intelligently coalesce TSO frames. Furthermore, add
a new packet scheduler which takes advantage of this estimate when
available. From Eric Dumazet.
13) Allow AF_PACKET fanouts with random selection, from Daniel
Borkmann.
14) Add ipv6 support to vxlan driver, from Cong Wang"
Resolved conflicts as per discussion.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1218 commits)
openvswitch: Fix alignment of struct sw_flow_key.
netfilter: Fix build errors with xt_socket.c
tcp: Add missing braces to do_tcp_setsockopt
caif: Add missing braces to multiline if in cfctrl_linkup_request
bnx2x: Add missing braces in bnx2x:bnx2x_link_initialize
vxlan: Fix kernel panic on device delete.
net: mvneta: implement ->ndo_do_ioctl() to support PHY ioctls
net: mvneta: properly disable HW PHY polling and ensure adjust_link() works
icplus: Use netif_running to determine device state
ethernet/arc/arc_emac: Fix huge delays in large file copies
tuntap: orphan frags before trying to set tx timestamp
tuntap: purge socket error queue on detach
qlcnic: use standard NAPI weights
ipv6:introduce function to find route for redirect
bnx2x: VF RSS support - VF side
bnx2x: VF RSS support - PF side
vxlan: Notify drivers for listening UDP port changes
net: usbnet: update addr_assign_type if appropriate
driver/net: enic: update enic maintainers and driver
driver/net: enic: Exposing symbols for Cisco's low latency driver
...
pcie_link_speed and pcix_bus_speed are arrays used by probe.c to correctly
convert lnksta register values into the pci_bus_speed enum. These static arrays
are useful outside probe for this purpose. This patch makes these defines into
conist arrays and exposes them with an extern header in drivers/pci/pci.h
-v2-
* move extern declarations to drivers/pci/pci.h
CC: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The dev_attrs field of struct class is going away soon, dev_groups
should be used instead. This converts the PCI class code to use the
correct field.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
On x86 platforms, the kernel respects PCI resource assignments from
the BIOS and only reassigns resources for unassigned BARs at boot
time. However, with the ACPI-based hotplug (acpiphp), it ignores the
BIOS' PCI resource assignments completely and reassigns all resources
by itself. This causes differences in PCI resource allocation
between boot time and runtime hotplug to occur, which is generally
undesirable and sometimes actively breaks things.
Namely, if there are enough resources, reassigning all PCI resources
during runtime hotplug should work, but it may fail if the resources
are constrained. This may happen, for instance, when some PCI
devices with huge MMIO BARs are involved in the runtime hotplug
operations, because the current PCI MMIO alignment algorithm may
waste huge chunks of MMIO address space in those cases.
On the Alexander's Sony VAIO VPCZ23A4R the BIOS allocates limited
MMIO resources for the dock station which contains a device
(graphics adapter) with a 256MB MMIO BAR. An attempt to reassign
that during runtime hotplug causes the dock station MMIO window to be
exhausted and acpiphp fails to allocate resources for the majority
of devices on the dock station as a result.
To prevent that from happening, modify acpiphp to follow the boot
time resources allocation behavior so that the BIOS' resource
assignments are respected during runtime hotplug too.
[rjw: Changelog]
References: https://bugzilla.kernel.org/show_bug.cgi?id=56531
Reported-and-tested-by: Alexander E. Patrakov <patrakov@gmail.com>
Tested-by: Illya Klymov <xanf@xanf.me>
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Cc: 3.9+ <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We had an inconsistent mix of using and omitting the "extern" keyword
on function declarations in header files. This removes them all.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/yinghai-root-bus-hotplug:
PCI: Put pci_dev in device tree as early as possible
PCI: Skip attaching driver in device_add()
PCI: acpiphp: Keep driver loaded even if no slots found
PCI/ACPI: Print info if host bridge notify handler installation fails
PCI: acpiphp: Move host bridge hotplug to pci_root.c
PCI/ACPI: acpiphp: Rename alloc_acpiphp_hp_work() to alloc_acpi_hp_work()
PCI: Make device create/destroy logic symmetric
PCI: Fix reference count leak in pci_dev_present()
PCI: Set pci_dev dev_node early so IOAPIC irq_descs are allocated locally
PCI: Add root bus children dev's res to fail list
PCI: acpiphp: Add is_hotplug_bridge detection
Conflicts:
drivers/pci/pci.h
* pci/yijing-ari:
PCI: shpchp: Iterate over all devices in slot, not functions 0-7
PCI: sgihp: Iterate over all devices in slot, not functions 0-7
PCI: cpcihp: Iterate over all devices in slot, not functions 0-7
PCI: pciehp: Iterate over all devices in slot, not functions 0-7
PCI: Consolidate "next-function" functions
PCI: Rename pci_enable_ari() to pci_configure_ari()
PCI: Enable ARI if dev and upstream bridge support it; disable otherwise
We want to put pci_dev structs in the device tree as soon as possible so
for_each_pci_dev() iteration will not miss them, but driver attachment
needs to be delayed until after pci_assign_unassigned_resources() to make
sure all devices have resources assigned first.
This patch moves device registering from pci_bus_add_devices() to
pci_device_add(), which happens earlier, leaving driver attachment in
pci_bus_add_devices().
It also removes unattached child bus handling in pci_bus_add_devices().
That's not needed because child bus via pci_add_new_bus() is already
in parent bus children list.
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
pci_enable_ari() now supports enabling or disabling ARI forwarding. So
rename pci_enable_ari() to pci_configure_ari() for easy understanding.
No functional change.
[bhelgaas: changelog]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Currently, the ACPI wakeup capability of PCI devices is set up
in two different places, partially in acpi_pci_bind() where
runtime wakeup is initialized and partially in
platform_pci_wakeup_init(), where system wakeup is initialized.
The cleanup is only done in acpi_pci_unbind() and it only covers
runtime wakeup.
Use the new .setup() and .cleanup() callbacks in struct acpi_bus_type
to consolidate that code and do the setup and the cleanup each in one
place.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Toshi Kani <toshi.kani@hp.com>
Host bridge hotplug:
- Untangle _PRT from struct pci_bus (Bjorn Helgaas)
- Request _OSC control before scanning root bus (Taku Izumi)
- Assign resources when adding host bridge (Yinghai Lu)
- Remove root bus when removing host bridge (Yinghai Lu)
- Remove _PRT during hot remove (Yinghai Lu)
SRIOV
- Add sysfs knobs to control numVFs (Don Dutile)
Power management
- Notify devices when power resource turned on (Huang Ying)
Bug fixes
- Work around broken _SEG on HP xw9300 (Bjorn Helgaas)
- Keep runtime PM enabled for unbound PCI devices (Huang Ying)
- Fix Optimus dual-GPU runtime D3 suspend issue (Dave Airlie)
- Fix xen frontend shutdown issue (David Vrabel)
- Work around PLX PCI 9050 BAR alignment erratum (Ian Abbott)
Miscellaneous
- Add GPL license for drivers/pci/ioapic (Andrew Cooks)
- Add standard PCI-X, PCIe ASPM register #defines (Bjorn Helgaas)
- NumaChip remote PCI support (Daniel Blueman)
- Fix PCIe Link Capabilities Supported Link Speed definition (Jingoo Han)
- Convert dev_printk() to dev_info(), etc (Joe Perches)
- Add support for non PCI BAR ROM data (Matthew Garrett)
- Add x86 support for host bridge translation offset (Mike Yoknis)
- Report success only when every driver supports AER (Vijay Pandarathil)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=OE3Q
-----END PGP SIGNATURE-----
Merge tag 'for-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI update from Bjorn Helgaas:
"Host bridge hotplug:
- Untangle _PRT from struct pci_bus (Bjorn Helgaas)
- Request _OSC control before scanning root bus (Taku Izumi)
- Assign resources when adding host bridge (Yinghai Lu)
- Remove root bus when removing host bridge (Yinghai Lu)
- Remove _PRT during hot remove (Yinghai Lu)
SRIOV
- Add sysfs knobs to control numVFs (Don Dutile)
Power management
- Notify devices when power resource turned on (Huang Ying)
Bug fixes
- Work around broken _SEG on HP xw9300 (Bjorn Helgaas)
- Keep runtime PM enabled for unbound PCI devices (Huang Ying)
- Fix Optimus dual-GPU runtime D3 suspend issue (Dave Airlie)
- Fix xen frontend shutdown issue (David Vrabel)
- Work around PLX PCI 9050 BAR alignment erratum (Ian Abbott)
Miscellaneous
- Add GPL license for drivers/pci/ioapic (Andrew Cooks)
- Add standard PCI-X, PCIe ASPM register #defines (Bjorn Helgaas)
- NumaChip remote PCI support (Daniel Blueman)
- Fix PCIe Link Capabilities Supported Link Speed definition (Jingoo
Han)
- Convert dev_printk() to dev_info(), etc (Joe Perches)
- Add support for non PCI BAR ROM data (Matthew Garrett)
- Add x86 support for host bridge translation offset (Mike Yoknis)
- Report success only when every driver supports AER (Vijay
Pandarathil)"
Fix up trivial conflicts.
* tag 'for-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (48 commits)
PCI: Use phys_addr_t for physical ROM address
x86/PCI: Add NumaChip remote PCI support
ath9k: Use standard #defines for PCIe Capability ASPM fields
iwlwifi: Use standard #defines for PCIe Capability ASPM fields
iwlwifi: collapse wrapper for pcie_capability_read_word()
iwlegacy: Use standard #defines for PCIe Capability ASPM fields
iwlegacy: collapse wrapper for pcie_capability_read_word()
cxgb3: Use standard #defines for PCIe Capability ASPM fields
PCI: Add standard PCIe Capability Link ASPM field names
PCI/portdrv: Use PCI Express Capability accessors
PCI: Use standard PCIe Capability Link register field names
x86: Use PCI setup data
PCI: Add support for non-BAR ROMs
PCI: Add pcibios_add_device
EFI: Stash ROMs if they're not in the PCI BAR
PCI: Add and use standard PCI-X Capability register names
PCI/PM: Keep runtime PM enabled for unbound PCI devices
xen-pcifront: Handle backend CLOSED without CLOSING
PCI: SRIOV control and status via sysfs (documentation)
PCI/AER: Report success only when every device has AER-aware driver
...
With the demise of CONFIG_HOTPLUG as an option, the pci_uevent
function located in hotplug.c will now always be used and doesn't need
special treatment in the Makefile. Move pci_uevent into pci-driver.c
and remove hotplug.c
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove conditional code based on CONFIG_HOTPLUG being false. It's
always on now in preparation of it going away as an option.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some implementations of SRIOV provide a capability structure
value of TotalVFs that is greater than what the software can support.
Provide a method to reduce the capability structure reported value
to the value the driver can support.
This ensures sysfs reports the current capability of the system,
hardware and software.
Example for its use: igb & ixgbe -- report 8 & 64 as TotalVFs,
but drivers only support 7 & 63 maximum.
Signed-off-by: Donald Dutile <ddutile@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Need type filled in device structure so it can be used for visible
attribute control in sysfs for pci_dev.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In https://bugzilla.kernel.org/show_bug.cgi?id=48981
Peter reported that /proc/bus/pci/??/??.? does not work for 3.6.
This is because the device configuration space registers are
not accessible if the corresponding parent bridge is suspended or
the device is put into D3cold state.
This is the same as /sys/bus/pci/devices/0000:??:??.?/config access
issue. So the function used to solve sysfs issue is used to solve
this issue.
This patch moves pci_config_pm_runtime_get()/_put() from pci/pci-sysfs.c
to pci/pci.c and makes them extern so they can be used by both the
sysfs and proc paths.
[bhelgaas: changelog, references, reporters]
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=48981
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=49031
Reported-by: Forrest Loomis <cybercyst@gmail.com>
Reported-by: Peter <lekensteyn@gmail.com>
Reported-by: Micael Dias <kam1kaz3@gmail.com>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CC: stable@vger.kernel.org # v3.6+
Commit cc2893b6 (PCI: Ensure we re-enable devices on resume)
addressed the problem with USB not being powered after resume on
recent Lenovo machines, but it did that in a suboptimal way.
Namely, it should have changed the relevant code paths only,
which are pci_pm_resume_noirq() and pci_pm_restore_noirq() supposed
to restore the device's power and standard configuration registers
after system resume from suspend or hibernation. Instead, however,
it modified pci_set_power_state() which is executed in several
other situations too. That resulted in some undesirable effects,
like attempting to change a device's power state in the same way
multiple times in a row (up to as many as 4 times in a row in the
snd_hda_intel driver).
Fix the bug addressed by commit cc2893b6 in an alternative way,
by forcibly powering up all devices in pci_pm_default_resume_early(),
which is called by pci_pm_resume_noirq() and pci_pm_restore_noirq()
to restore the device's power and standard configuration registers,
and modifying pci_pm_runtime_resume() to avoid the forcible power-up
if not necessary. Then, revert the changes made by commit cc2893b6
to make the confusion introduced by it go away.
Acked-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* topic/huang-d3cold-v7:
PCI/PM: add PCIe runtime D3cold support
PCI: do not call pci_set_power_state with PCI_D3cold
PCI/PM: add runtime PM support to PCIe port
ACPI/PM: specify lowest allowed state for device sleep state
This patch adds runtime D3cold support and corresponding ACPI platform
support. This patch only enables runtime D3cold support; it does not
enable D3cold support during system suspend/hibernate.
D3cold is the deepest power saving state for a PCIe device, where its main
power is removed. While it is in D3cold, you can't access the device at
all, not even its configuration space (which is still accessible in D3hot).
Therefore the PCI PM registers can not be used to transition into/out of
the D3cold state; that must be done by platform logic such as ACPI _PR3.
To support wakeup from D3cold, a system may provide auxiliary power, which
allows a device to request wakeup using a Beacon or the sideband WAKE#
signal. WAKE# is usually connected to platform logic such as ACPI GPE.
This is quite different from other power saving states, where devices
request wakeup via a PME message on the PCIe link.
Some devices, such as those in plug-in slots, have no direct platform
logic. For example, there is usually no ACPI _PR3 for them. D3cold
support for these devices can be done via the PCIe Downstream Port leading
to the device. When the PCIe port is powered on/off, the device is powered
on/off too. Wakeup events from the device will be notified to the
corresponding PCIe port.
For more information about PCIe D3cold and corresponding ACPI support,
please refer to:
- PCI Express Base Specification Revision 2.0
- Advanced Configuration and Power Interface Specification Revision 5.0
[bhelgaas: changelog]
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Originally-by: Zheng Yan <zheng.z.yan@intel.com>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
All callers of pci_do_scan_bus() are gone, so remove it.
Note that pci_do_scan_bus() was exported, so out-of-tree modules could
depend on it.
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This creates a generic pci_hp_add_bridge() that can be used by several
hotplug drivers.
[bhelgaas: split out from pciehp patch]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
VFIO PCI support will make use of these for user-initiated
PCI config accesses.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This isn't really a quirk; calling it directly from pci_add_device makes
more sense.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Let the user could enable and disable with pci=realloc=on or pci=realloc=off
Also
1. move variable and functions near the place they are used.
2. change macro to function
3. change related functions and variable to static and _init
4. update parameter description accordingly.
This will let us add a config option to control default behavior, and
still allow the user to turn off automatic reallocation if it fails on
their platform until a permanent solution is found.
-v2: still honor pci=realloc, and treat it as pci=realloc=on
also use enum instead of ...
-v3: update kernel-paramenters.txt according to Jesse.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We can reuse it for pciehp probing.
-v2: according to Kenji, fix crs timeout checking, and export the function
for later use when pciehp is compiled as a module.
Suggested-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
During S3 or S4 resume or PCI reset, ATS regs aren't restored correctly.
This patch enables ATS at the device state restore if PCI device has ATS
capability.
Signed-off-by: Xudong Hao <xudong.hao@intel.com>
Signed-off-by: Xiantao Zhang <xiantao.zhang@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
These new PCI services allow to probe for 2.3-compliant INTx masking
support and then use the feature from PCI interrupt handlers. The
services are properly synchronized with concurrent config space access
via sysfs or on device reset.
This enables generic PCI device drivers like uio_pci_generic or KVM's
device assignment to implement the necessary kernel-side IRQ handling
without any knowledge about device-specific interrupt status and control
registers.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Rafael J. Wysocki