This patch adds sysfs "role" for usb role swap. This parameter can be
read and write. If you use this file as the following, you can swap
the usb role.
For example:
1) Connect a usb cable using 2 Salvator-x boards
2) On A-Device (ID pin is low), you input the following command:
# echo peripheral > /sys/devices/platform/soc/ee080200.usb-phy/role
3) On B-Device (ID pin is high), you input the following command:
# echo host > /sys/devices/platform/soc/ee080200.usb-phy/role
Then, the A-device acts as a peripheral and the B-device acts as a host.
Please note that A-Device must input the following command if you
want the board to act as a host again. (even if you disconnect the usb
cable, since id state may be the same, the A-Device keeps to act as
peripheral.)
# echo host > /sys/devices/platform/soc/ee080200.usb-phy/role
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
If we configure the da8xx OTG phy in OTG mode, neither device or host
mode will work. That is because the PHY is not able to detect and notify
the driver that value of ID pin changed.
To work despite this hardware limitation, the da8xx glue implement a
workaround.
But to work, the workaround require the VBUS sense and the session end
comparator to enabled.
Enable them if the phy is configured in OTG mode.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
documentation.
This phy is only used on STiH415/6 based silicon, and support for
these SoC's is being removed from the kernel.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
documentation.
This phy is only used on STiH415/6 based silicon, and support for
these SoC's is being removed from the kernel.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
We found that the system crashed due to 480MHz output clock of
USB2 PHY was unstable after clock had been enabled by gpu module.
Theoretically, 1 millisecond is a critical value for 480MHz
output clock stable time, so we try to change the delay time
to 1.2 millisecond to avoid this issue.
And the commit ed907fb1d7c3 ("phy: rockchip-inno-usb2: correct
clk_ops callback") used prepare callbacks instead of enable
callbacks to support gate a clk if the operation may sleep. So
we can switch from delay to sleep functions.
Also fix a spelling error from "waitting" to "waiting".
Signed-off-by: William Wu <wulf@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Since we needs to delay ~1ms to wait for 480MHz output clock
of USB2 PHY to become stable after turn on it, the delay time
is pretty long for something that's supposed to be "atomic"
like a clk_enable(). Consider that clk_enable() will disable
interrupt and that a 1ms interrupt latency is not sensible.
The 480MHz output clock should be handled in prepare callbacks
which support gate a clk if the operation may sleep.
Signed-off-by: William Wu <wulf@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The rk3399 SoC USB2 PHY is comprised of one Host port and
one OTG port. And OTG port is for USB2.0 part of USB3.0 OTG
controller, as a part to construct a fully feature Type-C
subsystem.
With this patch, we can support OTG port with the following
functions:
- Support BC1.2 charger detect, and use extcon notifier to
send USB charger types to power driver.
- Support PHY suspend for power management.
- Support OTG Host only mode.
Signed-off-by: William Wu <wulf@rock-chips.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Both PHYs are sharing one reset line. With recent improvements to the
reset framework we can now also use reset_control_reset with shared
resets.
This allows us to drop some workarounds where the reset was only
specified for one PHY but not the other, to make sure that the reset it
only executed once (as the reset framework was not able to use
reset_control_reset with shared reset lines).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Fix the missing clk_disable_unprepare() before return from
phy_meson8b_usb2_power_on() in the error handling case.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This is a new driver for the USB PHY found in Meson8b and GXBB SoCs.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Now with musb driver implementing generic session bit based
PM, we need to have the USB PHYs behaving in a sane way for
platforms implementing PM.
Currently twl4030-usb enables PM in twl4030_phy_power_on()
and then disables it in twl4030_phy_power_off(). This will
block PM runtime for the SoC when no cable is connected.
Fix the issue by moving PM runtime autosuspend call to
happen where it gets called in twl4030_phy_power_on().
Note that this patch should not be backported to anything
before commit 467d5c9807 ("usb: musb: Implement session bit
based runtime PM for musb-core") as before that all the
glue layers implemented their own PM.
Fixes: 467d5c9807 ("usb: musb: Implement session bit based
runtime PM for musb-core")
Tested-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The common layer phy exit callback ufs_qcom_phy_exit()
calls phy_power_off() that has no meaning when phy_power_off()
callback is already registered with the phy provider and
the consumer makes use of the same.
Instead, add a no-op specific phy_exit() callback for now
to add the exit sequence at a later point.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add phy clock enable code to phy_power_on/off callbacks, and
remove explicit calls to enable these phy clocks from the
ufs-qcom hcd driver.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The phy init is meant to do phy initialization rather than
just getting the clock and regulator. Move these clock and
regulator get to probe(), to make room for actual phy
initialization sequence.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
remove() callback does a phy_power_off() only over the phy,
and nothing else now.
The phy_power_off() over the generic phy is called from the phy
consumer, and phy provider driver should not explicitly need to
call any phy ops.
So discard the remove callback for qcom-ufs phy platform drivers.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The tx_iface_clk and rx_iface_clk no longer exist with UFS Phy
present on msm8996. So skip obtaining these clocks using
compatible match.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a new compatible string for 14nm ufs phy present on msm8996
chipset. This phy is bit different from the legacy 14nm ufs phy
in terms of the clocks that are needed to be handled in the driver.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Different menthods pass around generic phy pointer to
extract device pointer. Instead, pass the device pointer
directly between function calls.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This helps us in avoiding any requirement for kfree() operation
to be called exclusively over the allocated string pointer.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
BUG_ON() are not preferred in the driver, plus the variable
on which BUG_ON is asserted is already checked in the code
before passing.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Allwinner SoC's PHY 0, when used as OTG controller, have no pmu part.
The code that poke some unknown bit of PMU for H3/A64 didn't check
the PHY, and will cause kernel oops when PHY 0 is used.
This patch will check whether the pmu is not NULL before poking.
Fixes: b3e0d141ca (phy: sun4i: add support for A64 usb phy)
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The deassert of phy_rst from exit callback is incorrect as when
doing phy_exit, we expect the phy_rst is on asserted state which was
done by power_off callback, but not deasserted state. Meanwhile when
disabling clk_pciephy_ref, the assert/deassert signal can't actually
take effect on the phy. So let's fix it anyway.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The ohci device name has changed in the board configuraion files,
hence, change the phy lookup table to match the new name.
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
twl4030_phy_power_on() initializes some bits which are required for
charging. As they are not set in twl4030_usb_runtime_resume()
a call to pm_runtime_get_sync() is not sufficient to enable charging.
This patch moves the initialization to twl4030_usb_runtime_resume()
so everything needed for charging is initialized upon
pm_runtime_get_sync().
That also gives improved possibilities to debug problems in that area
because the relevant parts can be checked separately. Charging can be
enabled without having the musb subsystem active.
As a side effect this hides some bugs in musb which causes
unbalanced calls to phy_power_off()/phy_power_on() so that
phy->power_count becomes -1.
The result is that e.g. the GTA04 phone (dm3730 + twl4030) works
finally as a usb gadget again and charging is working.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
setting twl->linkstat = MUSB_UNKNOWN upon error in musb_mailbox as
introduced in
commit 12b7db2bf8 ("usb: musb: Return error value from musb_mailbox")
causes twl4030_usb_irq() to not detect a state change form cable connected
to cable disconnected after such an error so that
pm_runtime_put_autosuspend() will not be called and the usage counter
gets unbalanced. Such errors happen e.g. if the omap2430 module is not
(yet) loaded during plug/unplug events.
This patch introduces a flag instead that indicates whether there is
information for the musb_mailbox pending and calls musb_mailbox() if
that flag is set.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The musb driver calls into this phy driver to disable/enable squelch
detection. This function was introduced in 24fe86a617 ("phy: sun4i-usb:
Add a sunxi specific function for setting squelch-detect"). This
function in turn calls sun4i_usb_phy_write, which uses a mutex to
guard the common access register. Unfortunately musb does this
in atomic context, which results in the following warning with lock
debugging enabled:
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:97
in_atomic(): 1, irqs_disabled(): 128, pid: 96, name: kworker/0:2
CPU: 0 PID: 96 Comm: kworker/0:2 Not tainted 4.8.0-rc4-00181-gd502f8ad1c3e #13
Hardware name: Allwinner sun8i Family
Workqueue: events musb_deassert_reset
[<c010bc01>] (unwind_backtrace) from [<c0109237>] (show_stack+0xb/0xc)
[<c0109237>] (show_stack) from [<c02a669b>] (dump_stack+0x67/0x74)
[<c02a669b>] (dump_stack) from [<c05d68c9>] (mutex_lock+0x15/0x2c)
[<c05d68c9>] (mutex_lock) from [<c02c3589>] (sun4i_usb_phy_write+0x39/0xec)
[<c02c3589>] (sun4i_usb_phy_write) from [<c03e6327>] (musb_port_reset+0xfb/0x184)
[<c03e6327>] (musb_port_reset) from [<c03e4917>] (musb_deassert_reset+0x1f/0x2c)
[<c03e4917>] (musb_deassert_reset) from [<c012ecb5>] (process_one_work+0x129/0x2b8)
[<c012ecb5>] (process_one_work) from [<c012f5e3>] (worker_thread+0xf3/0x424)
[<c012f5e3>] (worker_thread) from [<c0132dbd>] (kthread+0xa1/0xb8)
[<c0132dbd>] (kthread) from [<c0105f31>] (ret_from_fork+0x11/0x20)
Since the register access is mmio, we can use a spinlock to guard this
specific access, rather than the mutex that guards the entire phy.
Fixes: ba4bdc9e1d ("PHY: sunxi: Add driver for sunxi usb phy")
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
It is a hardware bug in RK3288, the only way to solve it is to
reset the phy.
Signed-off-by: Randy Li <ayaka@soulik.info>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The only use for this is for solving a hardware design problem in
usb of Rockchip RK3288.
Signed-off-by: Randy Li <ayaka@soulik.info>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Warn when external vbus is detected when we're trying to enable our
own vbus.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Together with some musb sunxi glue changes this allows run-time dr_mode
switching support via the "mode" musb sysfs attribute.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
If we cannot get dr_mode or no id gpio is specified simply assume
peripheral mode, as this is always safe.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The phy-sun4i-usb code supports forced ending a session on systems
which lack Vbus detection, to allow switching between host and peripheral
mode on such systems.
Role switching via the musb driver "mode" sysfs attribute requires force
ending the session too. This commit refactors the code to allow other
parts of the phy-sun4i-usb code to request a forced session end.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
We're using bool as true/false type in most places in phy-sun4i-usb.c
for consistency fixup the remaining uses of ints which are ever only
0 or 1 to be bools too.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Adds pm_runtime support for rockchip Type-C, so that power domain is
enabled only when there is a transaction going on to help save power.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The driver now calls of_usb_get_dr_mode_by_phy, which is part of the
USB core layer, and it fails to build when that is not provided:
drivers/phy/phy-sun4i-usb.o: In function `sun4i_usb_phy_probe':
phy-sun4i-usb.c:(.text.sun4i_usb_phy_probe+0x140): undefined reference to `of_usb_get_dr_mode_by_phy'
We already have a couple of other PHY drivers with a dependency
on USB_SUPPORT, so that seems to be the easiest fix here.
An alternative would be to adjust the #ifdef in include/linux/usb/of.h
to also check for CONFIG_USB_SUPPORT.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Fixes: b33ecca87d ("phy-sun4i-usb: Add support for peripheral-only mode")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add a PHY provider driver for the rk3399 SoC Type-c PHY. The USB
Type-C PHY is designed to support the USB3 and DP applications.
The USB3 operates in SuperSpeed mode and the DP can operate at RBR,
HBR and HBR2 data rates. This driver create 2 PHY devices separately
for USB3 and DisplyPort, and registers them under the child node.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Tested-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The syscon device in board config/device tree has been renamed.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
On kernel builds without COMMON_CLK, the newly added rockchip-inno-usb2
driver fails to build:
drivers/phy/phy-rockchip-inno-usb2.c:124:16: error: field 'clk480m_hw'
has incomplete type
struct clk_hw clk480m_hw;
In file included from include/linux/clk.h:16:0
from drivers/phy/phy-rockchip-inno-usb2.c:17:
include/linux/kernel.h:831:48: error: initialization from incompatible
pointer type [-Werror=incompatible-pointer-types]
const typeof( ((type *)0)->member ) *__mptr = (ptr); \
... ...
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Relying on PM-ops for shutting down PHY clocks was a
bad idea since the users (e.g. USB DWC3) might not
have been suspended by then.
Get rid of all PM-ops. It is the sole responsibility
of the PHY user to properly turn OFF and de-initialize
the PHY as part of its suspend routine.
Enable/disable PHY clock as part of ->init()/->exit()
call respectively. With this phy_init() and phy_exit()
can be called by PHY user during suspend/resume.
This is similar to what is done for ti-pipe3 driver.
See 31c8954efb1b ("phy: ti-pipe3: fix suspend")
The pm_runtime_enable() call in omap_usb2_probe()
is still required because without it, phy_create()
will not enable runtime PM on the phy device it
creates and phy_init() will not call
pm_runtime_get_sync().
Without pm_runtime_get_sync(), ocp2scp hwmod will
_not_ enable the IP and, thus, we will have abort
exceptions.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This driver can support for r8a7796 SoC. So, this patch adds it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add missing .owner field in ns2_pci_phy_ops, which is used for refcounting.
While at it, also makes ns2_pci_phy_ops const as it's never get modified.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-and-tested-by: Jon Mason <jon.mason@broadcom.com>
Reviewed-by: Pramod Kumar <pramodku@broadcom.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
By setting phy_set_drvdata(phy, mdiodev), struct ns2_pci_phy can be
removed.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-and-tested-by: Jon Mason <jon.mason@broadcom.com>
Reviewed-by: Pramod Kumar <pramodku@broadcom.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
We get 1 warning when building kernel with W=1:
drivers/phy/tegra/xusb.c:104:5: warning: no previous prototype for 'tegra_xusb_lane_lookup_function' [-Wmissing-prototypes]
In fact, this function is only used in the file in which it is
declared and don't need a declaration, but can be made static.
So this patch marks it 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
We get 5 warnings when building kernel with W=1:
drivers/phy/tegra/xusb.c:948:27: warning: no previous prototype for 'tegra_xusb_padctl_get' [-Wmissing-prototypes]
drivers/phy/tegra/xusb.c:981:6: warning: no previous prototype for 'tegra_xusb_padctl_put' [-Wmissing-prototypes]
drivers/phy/tegra/xusb.c:988:5: warning: no previous prototype for 'tegra_xusb_padctl_usb3_save_context' [-Wmissing-prototypes]
drivers/phy/tegra/xusb.c:998:5: warning: no previous prototype for 'tegra_xusb_padctl_hsic_set_idle' [-Wmissing-prototypes]
drivers/phy/tegra/xusb.c:1008:5: warning: no previous prototype for 'tegra_xusb_padctl_usb3_set_lfps_detect' [-Wmissing-prototypes]
In fact, these functions are declared in linux/phy/tegra/xusb.h,
so this patch adds missing header dependencies.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch to add a generic PHY driver for rockchip PCIe PHY.
Access the PHY via registers provided by GRF (general register
files) module.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The newer SoCs (rk3366, rk3399) take a different usb-phy IP block
than rk3288 and before, and most of phy-related registers are also
different from the past, so a new phy driver is required necessarily.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Suggested-by: Heiko Stuebner <heiko@sntech.de>
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Suggested-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Use of_property_read_bool to check for the existence of a property.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e1,e2,x;
@@
- if (of_get_property(e1,e2,NULL))
- x = true;
- else
- x = false;
+ x = of_property_read_bool(e1,e2);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Northstar is a family of SoCs used in home routers. They have USB 2.0
and 3.0 controllers with PHYs that need to be properly initialized.
This driver provides PHY init support in a generic way and can be bound
with XHCI controller driver.
There aren't any public datasheets from Broadcom so we can't have nice
defines for all used bits. It means we just follow Broadcom's
initialization procedure using their magic values. We were quite lucky
actually that Broadcom put some comments in their SDK reference code
explaining what given writes are responsible for.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
There's something unknown in the pmu part that shared with H3.
It's renamed as PMU_UNK1 from PMU_UNK_H3.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The 'reg' local variable does not need to be static.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This is likely that checking 'phy->hsic_clk' instead of 'phy->clk' is
expected here.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Chen-Yu Tsai <wens@csie.org
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Return proper error instead of 0 if brcm_sata_phy_init fails.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Use the new of_usb_get_dr_mode_by_phy() function to get the dr_mode
from the musb controller node instead of assuming that having an id_det
gpio means otg mode, and not having one means host mode.
Implement peripheral-only mode by adding a sun4i_usb_phy0_get_id_det
helper which looks at the dr_mode, always registering our extcon and
always monitoring vbus.
If dr_mode is not specified in the dts, do not register phy0 as we then
do not know how to treat it. This is actually a good thing as this means
we will not be registering phy0 on devices where the otg controller is
not enabled in the devicetree.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
- A couple of changes to improve the support for erase/discard/trim cmds
- Add eMMC HS400 enhanced strobe support
- Show OCR and DSR registers in SYSFS for MMC/SD cards
- Correct and improve busy detection logic for MMC switch (CMD6) cmds
- Disable HPI cmds for certain broken Hynix eMMC cards
- Allow MMC hosts to specify non-support for SD and MMC cmds
- Some minor additional fixes
MMC host:
- sdhci: Re-works, fixes and clean-ups
- sdhci: Add HW auto re-tuning support
- sdhci: Re-factor code to prepare for adding support for eMMC CMDQ
- sdhci-esdhc-imx: Fixes and clean-ups
- sdhci-esdhc-imx: Update system PM support
- sdhci-esdhc-imx: Enable HW auto re-tuning
- sdhci-bcm2835: Remove driver as sdhci-iproc is used instead
- sdhci-brcmstb: Add new driver for Broadcom BRCMSTB SoCs
- sdhci-msm: Add support for UHS cards
- sdhci-tegra: Improve support for UHS cards
- sdhci-of-arasan: Update phy support for Rockchip SoCs
- sdhci-of-arasan: Deploy enhanced strobe support
- dw_mmc: Some fixes and clean-ups
- dw_mmc: Enable support for erase/discard/trim cmds
- dw_mmc: Enable CMD23 support
- mediatek: Some fixes related to the eMMC HS400 support
- sh_mmcif: Improve support for HW busy detection
- rtsx_pci: Enable support for erase/discard/trim cmds
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wzSC
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.8' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- A couple of changes to improve the support for erase/discard/trim cmds
- Add eMMC HS400 enhanced strobe support
- Show OCR and DSR registers in SYSFS for MMC/SD cards
- Correct and improve busy detection logic for MMC switch (CMD6) cmds
- Disable HPI cmds for certain broken Hynix eMMC cards
- Allow MMC hosts to specify non-support for SD and MMC cmds
- Some minor additional fixes
MMC host:
- sdhci: Re-works, fixes and clean-ups
- sdhci: Add HW auto re-tuning support
- sdhci: Re-factor code to prepare for adding support for eMMC CMDQ
- sdhci-esdhc-imx: Fixes and clean-ups
- sdhci-esdhc-imx: Update system PM support
- sdhci-esdhc-imx: Enable HW auto re-tuning
- sdhci-bcm2835: Remove driver as sdhci-iproc is used instead
- sdhci-brcmstb: Add new driver for Broadcom BRCMSTB SoCs
- sdhci-msm: Add support for UHS cards
- sdhci-tegra: Improve support for UHS cards
- sdhci-of-arasan: Update phy support for Rockchip SoCs
- sdhci-of-arasan: Deploy enhanced strobe support
- dw_mmc: Some fixes and clean-ups
- dw_mmc: Enable support for erase/discard/trim cmds
- dw_mmc: Enable CMD23 support
- mediatek: Some fixes related to the eMMC HS400 support
- sh_mmcif: Improve support for HW busy detection
- rtsx_pci: Enable support for erase/discard/trim cmds"
* tag 'mmc-v4.8' of git://git.linaro.org/people/ulf.hansson/mmc: (135 commits)
mmc: rtsx_pci: Remove deprecated create_singlethread_workqueue
mmc: rtsx_pci: Enable MMC_CAP_ERASE to allow erase/discard/trim requests
mmc: rtsx_pci: Use the provided busy timeout from the mmc core
mmc: sdhci-pltfm: Drop define for SDHCI_PLTFM_PMOPS
mmc: sdhci-pltfm: Convert to use the SET_SYSTEM_SLEEP_PM_OPS
mmc: sdhci-pltfm: Make sdhci_pltfm_suspend|resume() static
mmc: sdhci-esdhc-imx: Use common sdhci_suspend|resume_host()
mmc: sdhci-esdhc-imx: Assign system PM ops within #ifdef CONFIG_PM_SLEEP
mmc: sdhci-sirf: Remove non needed #ifdef CONFIG_PM* for dev_pm_ops
mmc: sdhci-s3c: Remove non needed #ifdef CONFIG_PM for dev_pm_ops
mmc: sdhci-pxav3: Remove non needed #ifdef CONFIG_PM for dev_pm_ops
mmc: sdhci-of-esdhc: Simplify code by using SIMPLE_DEV_PM_OPS
mmc: sdhci-acpi: Simplify code by using SET_SYSTEM_SLEEP_PM_OPS
mmc: sdhci-pci-core: Simplify code by using SET_SYSTEM_SLEEP_PM_OPS
mmc: Change the max discard sectors and erase response when HW busy detect
phy: rockchip-emmc: Wait even longer for the DLL to lock
phy: rockchip-emmc: Be tolerant to card clock of 0 in power on
mmc: sdhci-of-arasan: Revert: Always power the PHY off/on when clock changes
mmc: sdhci-msm: Add support for UHS cards
mmc: sdhci-msm: Add set_uhs_signaling() implementation
...
Pull networking updates from David Miller:
1) Unified UDP encapsulation offload methods for drivers, from
Alexander Duyck.
2) Make DSA binding more sane, from Andrew Lunn.
3) Support QCA9888 chips in ath10k, from Anilkumar Kolli.
4) Several workqueue usage cleanups, from Bhaktipriya Shridhar.
5) Add XDP (eXpress Data Path), essentially running BPF programs on RX
packets as soon as the device sees them, with the option to mirror
the packet on TX via the same interface. From Brenden Blanco and
others.
6) Allow qdisc/class stats dumps to run lockless, from Eric Dumazet.
7) Add VLAN support to b53 and bcm_sf2, from Florian Fainelli.
8) Simplify netlink conntrack entry layout, from Florian Westphal.
9) Add ipv4 forwarding support to mlxsw spectrum driver, from Ido
Schimmel, Yotam Gigi, and Jiri Pirko.
10) Add SKB array infrastructure and convert tun and macvtap over to it.
From Michael S Tsirkin and Jason Wang.
11) Support qdisc packet injection in pktgen, from John Fastabend.
12) Add neighbour monitoring framework to TIPC, from Jon Paul Maloy.
13) Add NV congestion control support to TCP, from Lawrence Brakmo.
14) Add GSO support to SCTP, from Marcelo Ricardo Leitner.
15) Allow GRO and RPS to function on macsec devices, from Paolo Abeni.
16) Support MPLS over IPV4, from Simon Horman.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1622 commits)
xgene: Fix build warning with ACPI disabled.
be2net: perform temperature query in adapter regardless of its interface state
l2tp: Correctly return -EBADF from pppol2tp_getname.
net/mlx5_core/health: Remove deprecated create_singlethread_workqueue
net: ipmr/ip6mr: update lastuse on entry change
macsec: ensure rx_sa is set when validation is disabled
tipc: dump monitor attributes
tipc: add a function to get the bearer name
tipc: get monitor threshold for the cluster
tipc: make cluster size threshold for monitoring configurable
tipc: introduce constants for tipc address validation
net: neigh: disallow transition to NUD_STALE if lladdr is unchanged in neigh_update()
MAINTAINERS: xgene: Add driver and documentation path
Documentation: dtb: xgene: Add MDIO node
dtb: xgene: Add MDIO node
drivers: net: xgene: ethtool: Use phy_ethtool_gset and sset
drivers: net: xgene: Use exported functions
drivers: net: xgene: Enable MDIO driver
drivers: net: xgene: Add backward compatibility
drivers: net: phy: xgene: Add MDIO driver
...
Pull libata updates from Tejun Heo:
"libata saw quite a bit of activities in this cycle:
- SMR drive support still being worked on
- bug fixes and improvements to misc SCSI command emulation
- some low level driver updates"
* 'for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (39 commits)
libata-scsi: better style in ata_msense_*()
AHCI: Clear GHC.IS to prevent unexpectly asserting INTx
ata: sata_dwc_460ex: remove redundant dev_err call
ata: define ATA_PROT_* in terms of ATA_PROT_FLAG_*
libata: remove ATA_PROT_FLAG_DATA
libata: remove ata_is_nodata
ata: make lba_{28,48}_ok() use ATA_MAX_SECTORS{,_LBA48}
libata-scsi: minor cleanup for ata_scsi_zbc_out_xlat
libata-scsi: Fix ZBC management out command translation
libata-scsi: Fix translation of REPORT ZONES command
ata: Handle ATA NCQ NO-DATA commands correctly
libata-eh: decode all taskfile protocols
ata: fixup ATA_PROT_NODATA
libsas: use ata_is_ncq() and ata_has_dma() accessors
libata: use ata_is_ncq() accessors
libata: return boolean values from ata_is_*
libata-scsi: avoid repeated calculation of number of TRIM ranges
libata-scsi: reject WRITE SAME (16) with n_block that exceeds limit
libata-scsi: rename ata_msense_ctl_mode() to ata_msense_control()
libata-scsi: fix D_SENSE bit relection in control mode page
...
Two times out of 2000 reboots I ran into the error message
"rockchip_emmc_phy_power: dllrdy timeout". Presumably there is some
corner case where the DLL just takes a little longer to timeout. Let's
give it even more time to handle these corner cases.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It's possible that there are some reasons to turn the PHY on while the
clock is 0. In this case we just won't wait for the DLL to lock.
This is a bit of a stopgap until we figure out exactly when we're
supposed to wait for the DLL to lock and when we're supposed to power
cycle the PHY.
Note: this patch should help with suspend/resume where the system will
try to turn the PHY back on when the clock is 0.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The "phyctrl_frqsel" is described in the Arasan datasheet [1] as "the
frequency range of DLL operation". Although the Rockchip variant of
this PHY has different ranges than the reference Arasan PHY it appears
as if the functionality is similar. We should set this phyctrl field
properly.
Note: as per Rockchip engineers, apparently the "phyctrl_frqsel" is
actually only useful in HS200 / HS400 modes even though the DLL itself
it used for some purposes in all modes. See the discussion in the
earlier change in this series: ("mmc: sdhci-of-arasan: Always power the
PHY off/on when clock changes"). In any case, it shouldn't hurt to set
this always.
Note that this change should allow boards to run at HS200 / HS400 speed
modes while running at 100 MHz or 150 MHz. In fact, running HS400 at
150 MHz (giving 300 MB/s) is the main motivation of this series, since
performance is still good but signal integrity problems are less
prevelant at 150 MHz.
[1]: https://arasan.com/wp-content/media/eMMC-5-1-Total-Solution_Rev-1-3.pdf
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There's no reason to store the return value of rockchip_emmc_phy_power()
in a variable nor to check it. Just return it.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Previous PHY code waited a fixed amount of time for the DLL to lock at
power on time. Unfortunately, the time for the DLL to lock is actually
a bit more dynamic and can be longer if the card clock is slower.
Instead of waiting a fixed 30 us, let's now dynamically wait until the
lock bit gets set. We'll wait up to 10 ms which should be OK even if
the card clock is at the super slow 100 kHz.
On its own, this change makes the PHY power on code a little more
robust. Before this change the PHY was relying on the eMMC code to make
sure the PHY was only powered on when the card clock was set to at least
50 MHz before, though this reliance wasn't documented anywhere.
This change will be even more useful in future changes where we actually
need to be able to wait for a DLL lock at slower clock speeds.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some of the spacing was wrong (spaces instead of tabs), and due to
longer entries added later, the columns weren't aligned. Let's get
everything consistent.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The output tap delay controls helps maintain the hold requirements for
eMMC. The exact value is dependent on the SoC and other factors, though
it isn't really an exact science. But the default of 0 is not very good,
as it doesn't give the eMMC much hold time, so let's bump up to 4
(approx 90 degree phase?). If we need to configure this any further
(e.g., based on board or speed factors), we may need to consider a
device tree representation.
Suggested-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signal integrity analysis has suggested we set these values. Do this in
power_on(), so that they get reconfigured after suspend/resume.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to the databook, 10.2us is the max time for dll to be ready to
work. However in testing, some chips need 20us for dll to be ready. This
patch adds some extra margin for dllrdy to be ready, fixing our
-ETIMEDOUT issues.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
*) Add a new phy_ops for setting the phy mode
*) Add a new phy driver for DA8xx SoC USB PHY
*) Minor fixes and cleanups
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=5bMI
-----END PGP SIGNATURE-----
Merge tag 'phy-for-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-testing
Kishon writes:
phy: for 4.8 -rc1
*) Add a new phy_ops for setting the phy mode
*) Add a new phy driver for DA8xx SoC USB PHY
*) Minor fixes and cleanups
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Conflicts:
drivers/net/ethernet/mellanox/mlx5/core/en.h
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
drivers/net/usb/r8152.c
All three conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
If devm_add_action() fails we are explicitly calling the cleanup to free
the resources allocated. Lets use the helper devm_add_action_or_reset()
and return directly in case of error, as we know that the cleanup function
has been already called by the helper if there was any error.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The A31 companion pmic (axp221) does not generate vbus change interrupts
when the board is driving vbus, so we must poll when using the pmic for
vbus-det _and_ we're driving vbus.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
kzalloc will issue its own error message including a dump_stack()
so remote the site specific message.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
kzalloc will issue its own error message including a dump_stack()
so remote the site specific message.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The usb-phy is fully enclosed in the general register files (GRF).
Therefore as seen from the device-tree it shouldn't be a separate
platform-device but instead a sub-device of the GRF - using the
simply-mfd mechanism.
As the usb-phy is part of the kernel for some releases now, we keep
the old (and now deprecated) binding for compatibility purposes.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This is a new phy driver for the SoC USB controllers on the TI DA8xx
family of microcontrollers. The USB 1.1 PHY is just a simple on/off.
The USB 2.0 PHY also allows overriding the VBUS and ID pins.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The initial use for this is for PHYs that have a mode related to USB OTG.
There are several SoCs (e.g. TI OMAP and DA8xx) that have a mode setting
in the USB PHY to override OTG VBUS and ID signals.
Of course, the enum can be expaned in the future to include modes for
other types of PHYs as well.
Suggested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: David Lechner <david@lechnology.com>
No functional change. Rename "enum phy_mode" to
"enum xgene_phy_mode" in xgene phy driver in
preparation for adding set_mode callback in
phy core.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Loc Ho <lho@apm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=PpU9
-----END PGP SIGNATURE-----
Merge tag 'mfd-fixes-4.7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull more MFD fixes from Lee Jones:
"Apologies for missing these from the first pull request.
Final patches fixing Reset API change"
* tag 'mfd-fixes-4.7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
usb: dwc3: st: Use explicit reset_control_get_exclusive() API
phy: phy-stih407-usb: Use explicit reset_control_get_exclusive() API
phy: miphy28lp: Inform the reset framework that our reset line may be shared
Here are a number of small USB and PHY driver fixes for 4.7-rc6.
Nothing major here, all are described in the shortlog below. All have
been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iFYEABECABYFAld2ljcPHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfspN+sAn28Z
+GbDzyY5XwZ7Qs5/5uPYoGONAKCObDpgZr1A+/EMvDd57gfHWmFqTw==
=uYl3
-----END PGP SIGNATURE-----
Merge tag 'usb-4.7-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB and PHY fixes from Greg KH:
"Here are a number of small USB and PHY driver fixes for 4.7-rc6.
Nothing major here, all are described in the shortlog below. All have
been in linux-next with no reported issues"
* tag 'usb-4.7-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: don't free bandwidth_mutex too early
USB: EHCI: declare hostpc register as zero-length array
phy-sun4i-usb: Fix irq free conditions to match request conditions
phy: bcm-ns-usb2: checking the wrong variable
phy-sun4i-usb: fix missing __iomem *
phy: phy-sun4i-usb: Fix optional gpios failing probe
phy: rockchip-dp: fix return value check in rockchip_dp_phy_probe()
phy: rcar-gen3-usb2: fix unexpected repeat interrupts of VBUS change
usb: common: otg-fsm: add license to usb-otg-fsm
We're making all reset line users specify whether their lines are
shared with other IP or they operate them exclusively. In this case
the line is exclusively used only by this IP, so use the *_exclusive()
API accordingly.
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
On the STiH410 B2120 development board the MiPHY28lp shares its reset
line with the Synopsys DWC3 SuperSpeed (SS) USB 3.0 Dual-Role-Device
(DRD). New functionality in the reset subsystems forces consumers to
be explicit when requesting shared/exclusive reset lines.
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
- Use new reset_*_get_shared() variant to prevent reset line obtainment failure
- Fixes: 0b52297 ("reset: Add support for shared reset controls")
- Fix unintentional switch() fall-through into error path
- Fix uninitialised variable compiler warning
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=mo7m
-----END PGP SIGNATURE-----
Merge tag 'mfd-fixes-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD fixes from Lee Jones:
"Contained are some standard fixes and unusually an extension to the
Reset API. Some of those changes are required to fix a bug introduced
in -rc1, which introduces extra 'reset line checks' i.e. whether the
line is shared or not. If a line is shared and the new *_shared() API
is not used, the request fails with an error. This breaks USB in v4.7
for ST's platforms.
Admittedly, there are some patches contained in our (MFD/Reset)
immutable branch which are not true -fixes, but there isn't anything I
can do about that. Rest assured though, there aren't any API
'changes'. Everything is the same from the consumer's perspective.
- Use new reset_*_get_shared() variant to prevent reset line
obtainment failure (Fixes commit 0b52297f2288: "reset: Add support
for shared reset controls")
- Fix unintentional switch() fall-through into error path
- Fix uninitialised variable compiler warning"
* tag 'mfd-fixes-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: da9053: Fix compiler warning message for uninitialised variable
mfd: max77620: Fix FPS switch statements
phy: phy-stih407-usb: Inform the reset framework that our reset line may be shared
usb: dwc3: st: Inform the reset framework that our reset line may be shared
usb: host: ehci-st: Inform the reset framework that our reset line may be shared
usb: host: ohci-st: Inform the reset framework that our reset line may be shared
reset: TRIVIAL: Add line break at same place for similar APIs
reset: Supply *_shared variant calls when using *_optional APIs
reset: Supply *_shared variant calls when using of_* API
reset: Ensure drivers are explicit when requesting reset lines
reset: Reorder inline reset_control_get*() wrappers
Several cases of overlapping changes, except the packet scheduler
conflicts which deal with the addition of the free list parameter
to qdisc_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
On the STiH410 B2120 development board the ports on the Generic PHY
share their reset lines with each other. New functionality in the
reset subsystems forces consumers to be explicit when requesting
shared/exclusive reset lines.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
*) Fix in sun4i-usb phy driver to properly handle the return value of
gpiod_to_irq
*) Fix a sparse warning in sun4i-usb phy driver
*) Fix bcm-ns-usb2 phy driver to check the correct variable
*) Fix spurious interrupts during VBUS change in rcar-gen3-usb2 phy
driver
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=kUtK
-----END PGP SIGNATURE-----
Merge tag 'phy-for-4.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-linus
Kishon writes:
phy: for 4.7-rc5
*) Fix in sun4i-usb phy driver to properly handle the return value of
gpiod_to_irq
*) Fix a sparse warning in sun4i-usb phy driver
*) Fix bcm-ns-usb2 phy driver to check the correct variable
*) Fix spurious interrupts during VBUS change in rcar-gen3-usb2 phy
driver
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
commit 5cf700ac9d ("phy: phy-sun4i-usb: Fix optional gpios failing
probe")
changed the condition under which irqs are requested, but omitted matching
changes to sun4i_usb_phy_remove(). This commit fixes this.
Fixes: 5cf700ac9d ("phy: phy-sun4i-usb: Fix optional gpios failing probe")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
instead of defining all functions as static inlines,
let's move them to udc-core and export them with
EXPORT_SYMBOL_GPL, that way we can make sure that
only GPL drivers will use them.
As a side effect, it'll be nicer to add tracepoints
to the gadget API.
While at that, also fix Kconfig dependencies to
avoid randconfig build failures.
Acked-By: Sebastian Reichel <sre@kernel.org>
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We intended to test "usb2->phy" here instead of "dev".
Fixes: d3feb40673 ('phy: bcm-ns-usb2: new driver for USB 2.0 PHY on Northstar')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The interrupt 0 is not a valid interrupt number. In the event where the
retrieval of the vbus-det gpio would return null, the gpiod_to_irq
callback would return 0, while the current code makes the assumption
that it is a valid interrupt, and would go on calling request_irq.
Obviously, this would fail, preventing the driver from probing properly,
while the vbus and id gpios are optional.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
In case of error, the function devm_kzalloc() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should
be replaced with NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch fixes an issue that the driver is possible to cause
unexpected repeat interrupts if a board condition is wrong
(e.g. even if the ID pin is as function, a board supplies the VBUS.)
The reason why unexpected repeat interrupts happen is:
1) The driver changed the mode to function if it detected the ID pin
is high and the VBUS is high.
2) After the driver changed function mode, it disabled the "VBUS control"
feature. Then, the VBUS signal will be low.
3) Since the VBUS change interruption happened, the driver checked
the ID pin and VBUS.
4) Since VBUS was low, the driver changed the mode to host and enabled
the "VBUS control" feature. Then the VBUS signal will be high.
5) Since the VBUS change interruption happened, the driver did 1) above.
So, this patch modified the condition in rcar_gen3_device_recognition()
to check the ID pin only.
Fixes: 1114e2d (phy: rcar-gen3-usb2: change the mode to OTG on the combined channel)
Cc: <stable@vger.kernel.org> # v4.5+
Reported-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add PCI Phy support for Broadcom Northstar2 SoCs. This driver uses the
interface from the iproc mdio mux driver to enable the devices
respective phys.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
*) Fix compiler warning in exynos-mipi-video
*) Fix in ti-pipe3 PHY to program the DPLL
even if it was already locked
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJXWnWXAAoJEA5ceFyATYLZuPAP/0V/XbSQYq+lwOsSIgAN0q81
gPf14fDjg/i8sLl5U8t632LCE93xB+eHukVaka/XA5Ri2kwVP+SyErJIw5rcqxmb
HdEBY+8xw4uAS0oEr4rgbL/BBJMW5zl/+IeFL+VaUSH0uAW25hrNGGugnCOaFqNC
zcwGJwYBt6w6i2g6L+Y59K/TslPRw/n/SX0e29op/eyssmLb6lgGVR8icANqz+rT
CvgnghnRW8ljX4eJjQcp4WvVQcZRcHqNjX0jibf8TVrqY8ovL56kOzBSNfAkiGNj
S7j12kBvU+BWKY1MwtcBE6EAvQin/Wgq9Gm1mpSigqEGCk98El5XMpsyjwfZlViR
jD/bWhMuHojuN7tIWDsb2H6/sSJL9Fu94lVhGI6sLUs3fbV27P/qbeqox0aWJ8l8
CyN3qNTd/4HEbo/ty6w3Yzfu8WWyE8LzlVEkmnlfVEKhh3TQaX6hjiCd+lD0RNXY
nTvWMPzgOvENhLqRlKkUHJRuUTcTRFKgUHJVe82h8qHWqFRQN+0UfcUZ0Kosd2ms
6gZg1LQgl/TxX8QkgdVB3Z+zy2tfeqU06CecV9/pyOKkCqDUXOXqKg4SQ35AY06Y
PLLWCVyJhvkmW4ol35Atv9guRXrHZIyLEomhR4Qx5rzxxj1CekoJYVQr8D7ctwmV
H8jLjQKScFW3GZscTozS
=AmRN
-----END PGP SIGNATURE-----
Merge tag 'phy-for-4.7-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-linus
Kishon writes:
phy: for 4.7-rc
*) Fix compiler warning in exynos-mipi-video
*) Fix in ti-pipe3 PHY to program the DPLL
even if it was already locked
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
If bootloader has set a wrong DPLL then we must trash those values
and re-program it anyways. This fixes USB3 devices not being enumerated
on beagle-x15 if usb was started in u-boot.
We don't re-program SATA DPLL if it is locked as it was causing
SATA failures if device was hotpluged after boot.
Reported-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
At least on n900 we have phy-twl4030-usb only generating cable
interrupts, and then have a separate USB PHY.
In order for musb to know the real cable status, we need to
clear any cached state until musb is ready. Otherwise the cable
status interrupts will get just ignored if the status does
not change from the initial state.
To do this, let's add a return value to musb_mailbox(), and
reset cached linkstat to MUSB_UNKNOWN on error. Sorry to cause
a bit of churn here, I should have added that already last time
patching musb_mailbox().
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A rework of the exynos-mipi-video driver caused a warning
about the new __set_phy_state function potentially accessing
a variable before its initialization:
drivers/phy/phy-exynos-mipi-video.c: In function '__set_phy_state':
drivers/phy/phy-exynos-mipi-video.c:238:13: error: 'val' may be used uninitialized in this function [-Werror=maybe-uninitialized]
return val & data->resetn_val;
~~~~^~~~~~~~~~~~~~~~~~
drivers/phy/phy-exynos-mipi-video.c:235:6: note: 'val' was declared here
u32 val;
The failure scenario here is the offset passed into a the
stub regmap_read() function that does not modify its output,
however regmap_read() can also fail for other reasons, so
adding error handling (in this case, returning zero from
is_running) seems the best solution.
Note that this warning showed up with the ARM s5pv210_defconfig,
indicating that we most likely want to either enable CONFIG_REGMAP
in that defconfig as well, or disable the phy-exynos-mipi-video
driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: 97a3042f76 ("phy: exynos-mipi-video: Rewrite handling of phy registers")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Here's the big pull request for USB and PHY drivers for 4.7-rc1
Full details in the shortlog, but it's the normal major gadget driver
updates, phy updates, new usbip code, as well as a bit of lots of other
stuff.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlc/0P8ACgkQMUfUDdst+ykkFQCg0kJlxIiCU1FYBZYriqo4vX3F
9N8AoM/8nO8Y6vMpF2LWnamafYgqscTE
=ZuCh
-----END PGP SIGNATURE-----
Merge tag 'usb-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here's the big pull request for USB and PHY drivers for 4.7-rc1
Full details in the shortlog, but it's the normal major gadget driver
updates, phy updates, new usbip code, as well as a bit of lots of
other stuff.
All have been in linux-next with no reported issues"
* tag 'usb-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (164 commits)
USB: serial: ti_usb_3410_5052: add MOXA UPORT 11x0 support
USB: serial: fix minor-number allocation
USB: serial: quatech2: fix use-after-free in probe error path
USB: serial: mxuport: fix use-after-free in probe error path
USB: serial: keyspan: fix debug and error messages
USB: serial: keyspan: fix URB unlink
USB: serial: keyspan: fix use-after-free in probe error path
USB: serial: io_edgeport: fix memory leaks in probe error path
USB: serial: io_edgeport: fix memory leaks in attach error path
usb: Remove unnecessary space before operator ','.
usb: Remove unnecessary space before open square bracket.
USB: FHCI: avoid redundant condition
usb: host: xhci-rcar: Avoid long wait in xhci_reset()
usb/host/fotg210: remove dead code in create_sysfs_files
usb: wusbcore: Do not initialise statics to 0.
usb: wusbcore: Remove space before ',' and '(' .
USB: serial: cp210x: clean up CRTSCTS flag code
USB: serial: cp210x: get rid of magic numbers in CRTSCTS flag code
USB: serial: cp210x: fix hardware flow-control disable
USB: serial: option: add even more ZTE device ids
...
Driver updates for ARM SoCs, these contain various things that touch
the drivers/ directory but got merged through arm-soc for practical
reasons. For the most part, this is now related to power management
controllers, which have not yet been abstracted into a separate
subsystem, and typically require some code in drivers/soc or arch/arm
to control the power domains.
Another large chunk here is a rework of the NVIDIA Tegra USB3.0
support, which was surprisingly tricky and took a long time to
get done.
Finally, reset controller handling as always gets merged through here
as well.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=x+iD
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs, these contain various things that touch
the drivers/ directory but got merged through arm-soc for practical
reasons.
For the most part, this is now related to power management
controllers, which have not yet been abstracted into a separate
subsystem, and typically require some code in drivers/soc or arch/arm
to control the power domains.
Another large chunk here is a rework of the NVIDIA Tegra USB3.0
support, which was surprisingly tricky and took a long time to get
done.
Finally, reset controller handling as always gets merged through here
as well"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (97 commits)
arm-ccn: Enable building as module
soc/tegra: pmc: Add generic PM domain support
usb: xhci: tegra: Add Tegra210 support
usb: xhci: Add NVIDIA Tegra XUSB controller driver
dt-bindings: usb: xhci-tegra: Add Tegra210 XUSB controller support
dt-bindings: usb: Add NVIDIA Tegra XUSB controller binding
PCI: tegra: Support per-lane PHYs
dt-bindings: pci: tegra: Update for per-lane PHYs
phy: tegra: Add Tegra210 support
phy: Add Tegra XUSB pad controller support
dt-bindings: phy: tegra-xusb-padctl: Add Tegra210 support
dt-bindings: phy: Add NVIDIA Tegra XUSB pad controller binding
phy: core: Allow children node to be overridden
clk: tegra: Add interface to enable hardware control of SATA/XUSB PLLs
drivers: firmware: psci: make two helper functions inline
soc: renesas: rcar-sysc: Add support for R-Car H3 power areas
soc: renesas: rcar-sysc: Add support for R-Car E2 power areas
soc: renesas: rcar-sysc: Add support for R-Car M2-N power areas
soc: renesas: rcar-sysc: Add support for R-Car M2-W power areas
soc: renesas: rcar-sysc: Add support for R-Car H2 power areas
...
*) Add a new PHY driver for USB2 PHY on Northstar SoC
*) Add support for Broadcom NS2 SATA3 PHY in existing
Broadcom SATA3 PHY driver
*) Add support for MIPI DPHYs in Exynos5420-compatible
(5420, 5422 and 5800) and Exynos5433 SoCs
*) Add support for USB3 PHY on mt2701
*) Add extcon support for Renesas R-car USB2 PHY driver
*) Misc cleanups
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=uHWi
-----END PGP SIGNATURE-----
Merge tag 'phy-for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-testing
Kishon writes:
phy: for 4.7
*) Add a new PHY driver for USB2 PHY on Northstar SoC
*) Add support for Broadcom NS2 SATA3 PHY in existing
Broadcom SATA3 PHY driver
*) Add support for MIPI DPHYs in Exynos5420-compatible
(5420, 5422 and 5800) and Exynos5433 SoCs
*) Add support for USB3 PHY on mt2701
*) Add extcon support for Renesas R-car USB2 PHY driver
*) Misc cleanups
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch adds support for MIPI DPHYs found in Exynos5420-compatible
(5420, 5422 and 5800) and Exynos5433 SoCs. Those SoCs differs from
earlier by different offset of MIPI DPHY registers in PMU controllers
(Exynos 5420-compatible case) or by moving MIPI DPHY reset registers to
separate system register controllers (Exynos 5433 case). In both case
also additional 5th PHY (MIPI CSIS 2) has been added.
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Controlling Exynos MIPI DPHY is done by handling 2 registers: one for
phy reset and one for enabling it. This patch moves definitions of those
2 registers to speparate exynos_mipi_phy_desc structure, which can be
defined separately for each PHY for each supported hardware variant.
This code rewrite is needed to add support for newer Exynos SoCs, which
have MIPI PHY related registers at different offsets or even different
register regions.
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
There is no need to support access to the PMU through memory ioresource
as now access through PMU regmap should only be used.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Northstar is a family of SoCs used in home routers. They have USB 2.0
and 3.0 controllers with PHYs that need to be properly initialized.
This driver provides PHY init support in a generic way and can be bound
with an EHCI controller driver.
There are (just a few) registers being defined in bcma header. It's
because DMU/CRU registers will be also needed in other drivers. We will
need them e.g. in PCIe controller/PHY driver and at some point probably
in clock driver for BCM53573 chipset. By using include/linux/bcma/ we
avoid code duplication.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This flag is a no-op now (see commit 47b0eeb3dc "clk: Deprecate
CLK_IS_ROOT", 2016-02-02) so remove it.
Cc: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add a new OF device ID for mt2701
Some register settings to avoid RX sensitivity level degradation
which may arise on mt8173 platform are separated from other
platforms.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch adds extcon support for otg related channel.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
To handle the VBUS on/off by a regulator driver, this patch adds
regulator APIs calling in the driver and description about vbus-supply
in the rcar-gen3-phy-usb2.txt.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Since this driver uses the struct rcar_gen3_data in struct rcar_gen3_chan
only, we can remove the rcar_gen3_data.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch adds support for Broadcom NS2 SATA3 PHY in existing
Broadcom SATA3 PHY driver.
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add support for the XUSB pad controller found on Tegra210 SoCs. The
hardware is roughly the same, but some of the registers have been moved
around and the number and type of supported pads has changed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a new driver for the XUSB pad controller found on NVIDIA Tegra SoCs.
This hardware block used to be exposed as a pin controller, but it turns
out that this isn't a good fit. The new driver and DT binding much more
accurately describe the hardware and are more flexible in supporting new
SoC generations.
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to more flexibly support device tree bindings, allow drivers to
override the container of the child nodes. By default the device node of
the PHY provider is assumed to be the parent for children, but bindings
may decide to add additional levels for better organization.
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Currently, we have a common SATA3 PHY driver for all Broadcom
STB SoCs. This driver can be extended and re-used for Broadcom
iProc SoCs having same SATA3 PHY.
This patch renames existing Broadcom STB SATA3 PHY driver to
common Broadcom SATA3 PHY driver to share this PHY driver across
Broadcom SoCs.
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
A now redundant dependency on OF is also dropped.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
In the case of Renesas R-Car hardware we know that there are generations of
SoCs, e.g. Gen 2 and Gen 3. But beyond that its not clear what the
relationship between IP blocks might be. For example, I believe that
r8a7790 is older than r8a7791 but that doesn't imply that the latter is a
descendant of the former or vice versa.
We can, however, by examining the documentation and behaviour of the
hardware at run-time observe that the current driver implementation appears
to be compatible with the IP blocks on SoCs within a given generation.
For the above reasons and convenience when enabling new SoCs a
per-generation fallback compatibility string scheme being adopted for
drivers for Renesas SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
In the case of Renesas R-Car hardware we know that there are generations of
SoCs, e.g. Gen 2 and Gen 3. But beyond that its not clear what the
relationship between IP blocks might be. For example, I believe that
r8a7790 is older than r8a7791 but that doesn't imply that the latter is a
descendant of the former or vice versa.
We can, however, by examining the documentation and behaviour of the
hardware at run-time observe that the current driver implementation appears
to be compatible with the IP blocks on SoCs within a given generation.
For the above reasons and convenience when enabling new SoCs a
per-generation fallback compatibility string scheme being adopted for
drivers for Renesas SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Here's the big USB Gadget pull request. This time
not as large as usual with only 57 non-merge
commits.
The most important part here is, again, all the work
on dwc3. This time around we're treating all
endpoints (except for control endpoint) exactly the
same. They all have the same amount of TRBs on the
ring, they all treat the ring as an actual ring with
a link TRB pointing to the head, etc.
We're also helping the host side burst (on
SuperSpeed GEN1 or GEN2 at least) for as long as
possible until the endpoint returns NRDY.
Other than this big TRB ring rework on dwc3, we also
have a dwc3-omap DMA initialization fix, some extra
debugfs files to aid in some odd debug sessions and
a complete removal of our FIFO resizing logic.
We have a new quirk for some dwc3 P3 quirk in some
implementations.
The rest is basically non-critical fixes and the
usual cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7szP
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v4.7 merge window
Here's the big USB Gadget pull request. This time
not as large as usual with only 57 non-merge
commits.
The most important part here is, again, all the work
on dwc3. This time around we're treating all
endpoints (except for control endpoint) exactly the
same. They all have the same amount of TRBs on the
ring, they all treat the ring as an actual ring with
a link TRB pointing to the head, etc.
We're also helping the host side burst (on
SuperSpeed GEN1 or GEN2 at least) for as long as
possible until the endpoint returns NRDY.
Other than this big TRB ring rework on dwc3, we also
have a dwc3-omap DMA initialization fix, some extra
debugfs files to aid in some odd debug sessions and
a complete removal of our FIFO resizing logic.
We have a new quirk for some dwc3 P3 quirk in some
implementations.
The rest is basically non-critical fixes and the
usual cleanups.
The phy-am335x driver selects 'USB_COMMON', but all other drivers
use 'depends on' for that symbol, and it depends on USB || USB_GADGET
itself, which causes a Kconfig warning:
warning: (AM335X_PHY_USB) selects USB_COMMON which has unmet direct dependencies (USB_SUPPORT && (USB || USB_GADGET))
As suggested by Felipe Balbi, this turns the logic around, and makes
'USB_COMMON' selected by everything else that needs it, so we can
remove the dependencies.
Fixes: 59f042f644 ("usb: phy: phy-am335x: bypass first VBUS sensing for host-only mode")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Felipe Balbi <balbi@kernel.org>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The emmc-phy is fully enclosed in the general register files (GRF).
Therefore as seen from the device-tree it shouldn't be a separate platform-
device but instead a sub-device of the GRF - using the simply-mfd mechanism.
The driver entered the kernel in the current merge-window, so we can still
adapt the binding without needing a fallback, as the binding hasn't been
released with a full kernel yet.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The displayport-phy is fully enclosed in the general register files (GRF).
Therefore as seen from the device-tree it shouldn't be a separate platform-
device but instead a sub-device of the GRF - using the simply-mfd mechanism.
The driver entered the kernel in the current merge-window, so we can still
adapt the binding without needing a fallback, as the binding hasn't been
released with a full kernel yet.
While the edp phy is fully part of the GRF, it doesn't have any separate
register set there, so doesn't get any register-area assigned.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The twl4030 USB PHY driver uses UNIVERSAL_DEV_PM_OPS to access
its suspend/resume functions, which causes a warning about
unused symbols when CONFIG_PM is disabled:
drivers/phy/phy-twl4030-usb.c:394:12: error: 'twl4030_usb_runtime_suspend' defined but not used [-Werror=unused-function]
drivers/phy/phy-twl4030-usb.c:408:12: error: 'twl4030_usb_runtime_resume' defined but not used [-Werror=unused-function]
This adds __maybe_unused annotations to let the compiler know
it can silently drop the function definition.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dm816x USB PHY driver uses UNIVERSAL_DEV_PM_OPS to access
its suspend/resume functions, which causes a warning about
unused symbols when CONFIG_PM is disabled:
drivers/phy/phy-dm816x-usb.c:121:12: error: 'dm816x_usb_phy_runtime_suspend' defined but not used [-Werror=unused-function]
drivers/phy/phy-dm816x-usb.c:139:12: error: 'dm816x_usb_phy_runtime_resume' defined but not used [-Werror=unused-function]
This adds __maybe_unused annotations to let the compiler know
it can silently drop the function definition.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The phy-armada375-usb2 driver uses IOMEM functions so COMPILE_TEST && OF
build failed with:
drivers/built-in.o: In function `armada375_usb_phy_probe':
phy-armada375-usb2.c:(.text+0x121d): undefined reference to
`devm_ioremap_resource'
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Since the related driver (CPG/MSSR driver) only manages the first module
clock, this driver should not handle the HSUSB registers. So, this patch
removes the HSUSB registers handling.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Most newer Rockchip SoCs provide the possibility to use a usb-phy
as passthrough for the debug uart (uart2), making it possible to
for example get console output without needing to open the device.
This patch adds an early_initcall to enable this functionality
conditionally via the commandline and also disables the corresponding
usb controller in the devicetree.
Currently only data for the rk3288 is provided, but at least the
rk3188 and arm64 rk3368 also provide this functionality and will be
enabled later.
On a spliced usb cable the signals are tx on white wire(D+) and
rx on green wire(D-).
The one caveat is that currently the reconfiguration of the phy
happens as early_initcall, as the code depends on the unflattened
devicetree being available. Everything is fine if only a regular
console is active as the console-replay will happen after the
reconfiguation. But with earlycon active output up to smp-init
currently will get lost.
The phy is an optional property for the connected dwc2 controller,
so we still provide the phy device but fail all phy-ops with -EBUSY
to make sure the dwc2 does not try to transmit anything on the
repurposed phy.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add phy driver for the Rockchip DisplayPort PHY module. This
is required to get DisplayPort working in Rockchip SoCs.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch to add a generic PHY driver for ROCKCHIP eMMC PHY.
Access the PHY via registers provided by GRF (general register
files) module.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
If we reload phy-twl4030-usb, we get a warning about unbalanced
pm_runtime_enable. Let's fix the issue and also fix idling of the
device on unload before we attempt to shut it down.
If we don't properly idle the PHY before shutting it down on removal,
the twl4030 ends up consuming about 62mW of extra power compared to
running idle with the module loaded.
Cc: stable@vger.kernel.org
Cc: Bin Liu <b-liu@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: NeilBrown <neil@brown.name>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Otherwise rmmod omap2430; rmmod phy-twl4030-usb; modprobe omap2430
will try to use a non-existing phy and oops:
Unable to handle kernel paging request at virtual address b6f7c1f0
...
[<c048a284>] (devm_usb_get_phy_by_node) from [<bf0758ac>]
(omap2430_musb_init+0x44/0x2b4 [omap2430])
[<bf0758ac>] (omap2430_musb_init [omap2430]) from [<bf055ec0>]
(musb_init_controller+0x194/0x878 [musb_hdrc])
Cc: stable@vger.kernel.org
Cc: Bin Liu <b-liu@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: NeilBrown <neil@brown.name>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
If phy_pm_runtime_get_sync failed but we already
enable regulator, current code return directly without
doing regulator_disable. This patch fix this problem
and cleanup err handle of phy_power_on to be more readable.
Fixes: 3be88125d8 ("phy: core: Support regulator ...")
Cc: <stable@vger.kernel.org> # v3.18+
Cc: Roger Quadros <rogerq@ti.com>
Cc: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The HiSilicon Hi6220 USB PHY is available in HiSilicon Hi6220 SoCs only.
Restrict it to HiSilicon arm64, unless compile-testing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
*) new PHY driver for hi6220 usb and rcar gen3 usb2
*) deprecate phy-omap-control driver. phy-omap-control driver was added
when there was no proper infrastructure for doing control module
initialization. The phy-omap-control driver is not an 'actual' PHY
driver and it was just a hack to do PHY related control module
initialization. Now with SYSCON framework in the kernel, control
module setttings can be done using APIs provided by syscon.
*) usbphy-internal pll creates the needed 480MHz and is also a
supply-clock back to the core clock-controller in Rockchip SoCs.
This is now modeled as a real clock.
*) calibrate mt65xx usb3 PHY for better eye diagram and receiver
sensitivity.
*) Miscellaneous cleanups.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Bu7H
-----END PGP SIGNATURE-----
Merge tag 'phy-for-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 4.5
*) new PHY driver for hi6220 usb and rcar gen3 usb2
*) deprecate phy-omap-control driver. phy-omap-control driver was added
when there was no proper infrastructure for doing control module
initialization. The phy-omap-control driver is not an 'actual' PHY
driver and it was just a hack to do PHY related control module
initialization. Now with SYSCON framework in the kernel, control
module setttings can be done using APIs provided by syscon.
*) usbphy-internal pll creates the needed 480MHz and is also a
supply-clock back to the core clock-controller in Rockchip SoCs.
This is now modeled as a real clock.
*) calibrate mt65xx usb3 PHY for better eye diagram and receiver
sensitivity.
*) Miscellaneous cleanups.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
A ton of improvements to dwc2 have been made. The
driver should be a lot more stable on v4.5 then ever
before.
Our good old dwc3 got a few cleanups and misc fixes
and also added support to Xilinx's integration of
this IP.
Yoshihiro Shimoda gives us support for a new USB3
peripheral controller from Renesas.
Other than these, the usual misc fixes all over the
place.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8vM4
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.5
A ton of improvements to dwc2 have been made. The
driver should be a lot more stable on v4.5 then ever
before.
Our good old dwc3 got a few cleanups and misc fixes
and also added support to Xilinx's integration of
this IP.
Yoshihiro Shimoda gives us support for a new USB3
peripheral controller from Renesas.
Other than these, the usual misc fixes all over the
place.
Deprecate using phy-omap-control driver to power on/off the PHY,
and use *syscon* framework to do the same. This handles
powering on/off the PHY for the USB2 PHYs used in various TI SoCs.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
No functional change. Previously omap_control_phy_power() was used to power
off the PHY during probe. But once phy-omap-usb2 driver is adapted to
use syscon, omap_control_phy_power() cannot be used. Hence used
omap_usb_power_off to power off the PHY.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Deprecate using phy-omap-control driver to set PCS value of the PHY
and start using *syscon* API to do the same.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Deprecate using phy-omap-control driver to power on/off the PHY and
use *syscon* framework to do the same.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
No functional change. Previously omap_control_phy_power() was used to power
off the PHY during probe. But once PIPE3 driver is adapted to use syscon,
omap_control_phy_power() cannot be used. Hence used ti_pipe3_power_off
to power off the PHY.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
No functional change. Moved mem resource initialization done in
probe to a separate function as part of cleaning up
ti_pipe3_probe.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
No functional change. Moved sysctrl initialization done in probe to a
separate function as part of cleaning up ti_pipe3_probe.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
No functional change. Moved clock initialization done in probe to a
separate function as part of cleaning up ti_pipe3_probe.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
No functional change. Introduce local struct device pointer in
probe and replace using &pdev->dev/phy->dev with the local
device pointer. This is in preparation to split ti_pipe3_probe
and add separate functions for getting mem resource, getting
sysctrl and getting clocks.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
After commit 739ae3452d ("phy: berlin-usb: Set drvdata for phy and
use it"), we get the address of priv by phy_get_drvdata(), so there's
no need to set device's driver_data any more. This patch removes the
call of platform_set_drvdata().
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
We don't need gpio related header files, so remove them.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The BCM7xxx ARM-based and MIPS-based platforms share a similar hardware
block for AHCI SATA3.
This new compatible string, "brcm,bcm7425-sata-phy", may be used for
most MIPS-based platforms of 40nm process technology.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add data for phy version, and the default value of version is using the
BRCM_SATA_PHY_28NM.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The USB phys on Rockchip SoCs contain their own internal PLLs to create
the 480MHz needed. Additionally this PLL output is also fed back into the
core clock-controller as possible source for clocks like the GPU or others.
Until now this was modelled incorrectly with a "virtual" factor clock in
the clock controller. The one big caveat is that if we turn off the usb phy
via the siddq signal, all analog components get turned off, including the
PLLs. It is therefore possible that a source clock gets disabled without
the clock driver ever knowing, possibly making the system hang.
Therefore register the phy-plls as real clocks that the clock driver can
then reference again normally, making the clock hirarchy finally reflect
the actual hardware.
The phy-ops get converted to simply turning that new clock on and off
which in turn controls the siddq signal of the phy.
Through this the driver gains handling for platform-specific data, to
handle the phy->clock name association.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
We need custom handling for these two socs in the driver shortly,
so add the necessary compatible values to binding and driver.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This unclutters the loop in probe a lot and makes current (and future)
error handling easier to read.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This introduces a common struct that holds data belonging to
the umbrella device that contains all the phys and that we
want to use later.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Currently the phy driver only gets the optional clock reference but
never puts it again, neither during error handling nor on remove.
Fix that by moving the clk_put to a devm-action that gets called at
the right time when all other devm actions are done.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Support hi6220 use phy for HiKey board
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Note this commit only adds support for phys 1-3, phy 0, the otg phy, is
not yet (fully) supported after this commit.
Signed-off-by: Reinder de Haan <patchesrdh@mveas.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Use of_match_node instead of calling of_device_is_compatible a ton of
times to get model specific config data.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
calibrate HS slew rate and switch 100uA current to SSUSB
to improve HS eye diagram of HQA test.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
when use the default value 8 of RG_USB20_SQTH, the HS receiver
sensitivity test of HQA will fail, set it as 2 to fix up the
issue.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch adds support for runtime ID/VBUS pin detection if
the channel 0 of R-Car gen3 is used. So, we are able to use
the channel as both host and peripheral.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
To use the channel 0 of R-Car gen3 as periperal mode, This patch changes
the mode to OTG instead of HOST. Then, this driver needs to set some
registers to enable host mode and detects ID pin and VBUS pin at
phy_init() timing.
For now, the channel 0 can be used as host mode only.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch adds support for R-Car generation 3 USB2 PHY driver.
This SoC has 3 EHCI/OHCI channels, and the channel 0 is shared
with the HSUSB (USB2.0 peripheral) device. And each channel has
independent registers about the PHYs.
So, the purpose of this driver is:
1) initializes some registers of SoC specific to use the
{ehci,ohci}-platform driver.
2) detects id pin to select host or peripheral on the channel 0.
For now, this driver only supports 1) above.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
We currently can't unload omap2430 MUSB platform glue driver module and
this cause issues for fixing the MUSB code further. The reason we can't
remove omap2430 is because it uses the PHY functions and also exports the
omap_musb_mailbox function that some PHY drivers are using.
Let's fix the issue by exporting a more generic musb_mailbox function
from the MUSB core and allow platform glue layers to register phy_callback
function as needed.
And now we can now also get rid of the include/linux/musb-omap.h.
Cc: Bin Liu <b-liu@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: NeilBrown <neil@brown.name>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
On driver detach, devm_phy_release() will put a refcount to
the phy, so gets a refconut to it before return.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
for_each_available_child_of_node performs an of_node_get on each iteration,
so a return from the middle of the loop requires an of_node_put.
A simplified version of the semantic patch that finds this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_available_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
* return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
for_each_child_of_node performs an of_node_get on each iteration,
so a return from the middle of the loop requires an of_node_put.
A simplified version of the semantic patch that finds this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
* return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
for_each_child_of_node performs an of_node_get on each iteration,
so a return from the middle of the loop requires an of_node_put.
A simplified version of the semantic patch that finds this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
* return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
for_each_available_child_of_node performs an of_node_get on each iteration,
so a return from the middle of the loop requires an of_node_put.
A simplified version of the semantic patch that finds this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_available_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
* return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
for_each_available_child_of_node performs an of_node_get on each iteration,
so a return from the middle of the loop requires an of_node_put.
A simplified version of the semantic patch that finds this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_available_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
* return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
for_each_child_of_node performs an of_node_get on each iteration,
so a return from the middle of the loop requires an of_node_put.
A simplified version of the semantic patch that finds this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
* return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
for_each_available_child_of_node performs an of_node_get on each iteration,
so a return from the middle of the loop requires an of_node_put.
A simplified version of the semantic patch that finds this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_available_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
* return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The sun9i usb phy driver calls of_usb_get_phy_mode(), which is not
available if USB is disabled:
drivers/built-in.o: In function `sun9i_usb_phy_probe':
:(.text+0x7fb0): undefined reference to `of_usb_get_phy_mode'
This adds a dependency to avoid the randconfig build errors.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 9c3b443026 ("phy: Add driver to support individual USB PHYs on sun9i")
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Here is the big USB patchset for 4.4-rc1.
As usual, most of the changes are in the gadget subsystem, and we
removed a host controller for a device that is no longer in existance,
and probably never was even made public. There is also other minor
driver updates and new device ids, full details in the changelog.
All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlY6gVMACgkQMUfUDdst+ynLZgCePfhiDuwriaX7osq90HDu8JOc
pTEAn2dBdw2VMPToUlxccR963YSfgu2A
=mMgp
-----END PGP SIGNATURE-----
Merge tag 'usb-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here is the big USB patchset for 4.4-rc1.
As usual, most of the changes are in the gadget subsystem, and we
removed a host controller for a device that is no longer in existance,
and probably never was even made public. There is also other minor
driver updates and new device ids, full details in the changelog.
All of these have been in linux-next for a while"
* tag 'usb-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (233 commits)
USB: core: Codestyle fix in urb.c
usb: misc: usb3503: Use i2c_add_driver helper macro
usb: host: lpc32xx: don't unregister phy device
usb: host: lpc32xx: balance clk enable/disable on removal
usb: host: lpc32xx: fix warnings caused by enabling unprepared clock
uwb: drp: Use setup_timer
uwb: neh: Use setup_timer
uwb: rsv: Use setup_timer
USB: qcserial: add Sierra Wireless MC74xx/EM74xx
usb: chipidea: otg: don't wait vbus drops below BSV when starts host
chipidea: ci_hdrc_pci: use PCI_VDEVICE() instead of PCI_DEVICE()
doc: dt-binding: ci-hdrc-usb2: split vendor specific properties
usb: chipidea: imx: add imx6ul usb support
doc: dt-binding: ci-hdrc-usb2: improve property description
usb: chipidea: imx: add usb support for imx7d
Doc: usb: ci-hdrc-usb2: Add phy-clkgate-delay-us entry
usb: chipidea: Add support for 'phy-clkgate-delay-us' property
usb: chipidea: Use extcon framework for VBUS and ID detect
usb: gadget: net2280: restore ep_cfg after defect7374 workaround
usb: dwc2: host: Fix use after free w/ simultaneous irqs
...
This patch adds the PCIe PHY support for the Broadcom PCIe RC interface
on Cygnus
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Arun Parameswaran <aparames@broadcom.com>
Reviewed-by: JD (Jiandong) Zheng <jdzheng@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Both data->id_det_gpio and data->vbus_det_gpio are optional, so use
devm_gpiod_get_optional for them.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Exynos USB2 PHY has separate power supply, which is usually provided by
VBUS regulator. This patch adds support for it. VBUS regulator is
optional, to keep compatibility with boards, which have VBUS provided
from some always-on power source.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
rockchip phy are enable when soc reset, to save power consumption,
we disable it when probe, and enable each phy when it use
Signed-off-by: huang lin <hl@rock-chips.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
After commit:
654672d4ba ("locking/atomics: Add _{acquire|release|relaxed}() variants of some atomic operations")
Architectures may only provide {cmp,}xchg_relaxed definitions in
asm/cmpxchg.h. Other variants, such as {cmp,}xchg, may be built in
linux/atomic.h, which means simply including asm/cmpxchg.h may not get
the definitions of all the{cmp,}xchg variants.
Therefore, we should privatize the inclusions of asm/cmpxchg.h to
keep it only included in arch/* and replace the inclusions outside
with linux/atomic.h
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Aybuke Ozdemir <aybuke.147@gmail.com>
Cc: Chris Brannon <chris@the-brannons.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Kirk Reiser <kirk@reisers.ca>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Shradha Shah <sshah@solarflare.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: William Hubbs <w.d.hubbs@gmail.com>
Cc: devel@driverdev.osuosl.org
Cc: linux-net-drivers@solarflare.com
Cc: speakup@linux-speakup.org
Link: http://lkml.kernel.org/r/1440589966-26280-1-git-send-email-boqun.feng@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Core changes:
- Root out the wrapper devm_gpiod_get() and gpiod_get() etc
versions of the descriptor calls that did not use the flags
argument on the end. This was around for too long and eventually
Uwe Kleine-König took the time to clean it out and the last
users are removed along with the macros in this tag. In several
cases the use of flags simplifies the code. For this reason we
have (ACKed) patches hitting in DRM, IIO, media, NFC, USB+PHY
up until we hammer in the nail with removing the macros.
- Add a fat document describing how much ready-made GPIO stuff
we have i the kernel to discourage people from reinventing
a square wheel in userspace, as so often happens.
- Create a separate lockdep class for each instance of a GPIO
IRQ chip instead of using one class for all chips, as the current
code will not work with systems with several GPIO chips doing
lockdep debugging.
- Protect against driver unloading also when a GPIO line is only
used as IRQ for the GPIOLIB_IRQCHIP helpers.
- If the GPIO chip has no designated owner, assign the parent
device driver owner as owner.
- Consolidation of chained IRQ handler install/remove replacing
all call sites where irq_set_handler_data() and
irq_set_chained_handler() were done in succession with a
combined call to irq_set_chained_handler_and_data(). This
series was created by Thomas Gleixner after the problem was
observed by Russell King.
- Tglx also made another series of patches switching
__irq_set_handler_locked() for irq_set_handler_locked() which
is way cleaner.
- Tglx and Jiang Liu wrote a good bunch of patches to make use of
irq_desc_get_xxx() accessors and avoid looking up irq_descs
from IRQ numbers. The goal is to get rid of the irq number
from the handlers in the IRQ flow which is nice.
- Rob Herring killed off the set_irq_flags() for all GPIO
drivers. This was an ARM specific function that is replaced
with the generic irq_modify_status() where special flags
are actually needed.
- When an OF node has a pin range for its GPIOs, return
-EPROBE_DEFER if the pin controller isn't available.
Pretty logical, yet needed to be fixed.
- If a driver using GPIOLIB_IRQCHIP has its own
irq_*_resources call back, then call these instead of the
defaults provided by the GPIOLIB.
- Fix an undocumented ABI hole: named GPIOs were not
properly documented.
Driver improvements:
- Add get_direction() support to the generic GPIO driver, it's
strange that we didn't have that before.
- Make it possible to have input-only GPIO chips using the
generic GPIO driver.
- Clean out platform data support from the Emma Mobile (EM)
driver
- Finegrained runtime PM support for the RCAR driver.
- Support r8a7795 (R-car H3) in the RCAR driver.
- Support interrupts on GPIOs 16 thru 31 in the DaVinci driver.
- Some consolidation and new support in the MPC8xxx driver,
we now support MPC5125.
- Preempt-RT-friendly patches: the OMAP, MPC8xxx, drivers uses raw
spinlocks making it work better with the realime patches.
- Interrupt support for the EXTRAXFS GPIO driver.
- Make the ETRAXFS GPIO driver support also ARTPEC-3.
- Interrupt and wakeup support for the BRCMSTB driver, also for
wakeup from S5 cold boot.
- Mask MXC IRQs during suspend.
- Improve OMAP2 GPIO set_debounce() to work according to spec.
- The VF610 driver handles IRQs properly.
New drivers:
- ZTE ZX GPIO driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJV52lvAAoJEEEQszewGV1zOVcP/2ZgkfRgl119LZnWShfrEJWq
UXaNzSaPNgvDzvGaqqi62SZQuhrdIWRKfMPtAuMGbEn5aJx0JC5UAOYjjfkKBqpO
toqc1w2DScc0JTorY8qgczIBDO1A3ZBAcIvXXpOduy/JaKPoQteRN8WYTynPw48/
0+97ZODwhyOkfeqmvUClkc9gW4XT68dudb0Lv1nQjsZmd1dHF2PZlwH3aL9sV68j
GJAqf09xNqZaWWQBhs+J3ptsYjaJfYjo9NOOUf0Y/UgqXO3vB+2S4EmRATaRHS2F
aHdj03sNZCNSDEa35WwetbLRGxPzSWmfxmBzQQ1baGdcJICn7Yv58EklPKRvwtMo
ZpUsgiOV4OUIEClPJohs4xbl2HRsOYB3VbcihkXjVAxS6i2/jgA3Tn8ATvUSZ8wq
TX8D6BfciigRCkT2G+B0TQBmcX1IQsMd1DBUNfw7Dk1TK/vxH4UYWbke422RjKGz
ORJ+0DfShMCdYjrCVlt7UbFcqE3L5CnrztLQ3oFt0om2JsSWztV9V579G+Dqo9CI
fE4G3xlsF33UCvXcmnOp6PuU+ZYBodLggkmK4REy2D3LCOnkcKq0U8Fj5RssApZ9
FdqVYck555ZpcBiN8ihB97WsmU+0XhBjblCbgzr6GxUw8EJ4x8H9nlraA6bluFoP
9c2qgPxjCq/VWA/F0YOU
=iQ2P
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.3 kernel cycle.
There is quite a lot going on in the GPIO subsystem this merge window,
so the main matter is decribed below.
The hits in other subsystems when making the GPIO flags optional are
all ACKed by their respective subsystem maintainers.
Core changes:
- Root out the wrapper devm_gpiod_get() and gpiod_get() etc versions
of the descriptor calls that did not use the flags argument on the
end. This was around for too long and eventually Uwe Kleine-König
took the time to clean it out and the last users are removed along
with the macros in this tag. In several cases the use of flags
simplifies the code. For this reason we have (ACKed) patches
hitting in DRM, IIO, media, NFC, USB+PHY up until we hammer in the
nail with removing the macros.
- Add a fat document describing how much ready-made GPIO stuff we
have i the kernel to discourage people from reinventing a square
wheel in userspace, as so often happens.
- Create a separate lockdep class for each instance of a GPIO IRQ
chip instead of using one class for all chips, as the current code
will not work with systems with several GPIO chips doing lockdep
debugging.
- Protect against driver unloading also when a GPIO line is only used
as IRQ for the GPIOLIB_IRQCHIP helpers.
- If the GPIO chip has no designated owner, assign the parent device
driver owner as owner.
- Consolidation of chained IRQ handler install/remove replacing all
call sites where irq_set_handler_data() and
irq_set_chained_handler() were done in succession with a combined
call to irq_set_chained_handler_and_data().
This series was created by Thomas Gleixner after the problem was
observed by Russell King.
- Tglx also made another series of patches switching
__irq_set_handler_locked() for irq_set_handler_locked() which is
way cleaner.
- Tglx and Jiang Liu wrote a good bunch of patches to make use of
irq_desc_get_xxx() accessors and avoid looking up irq_descs from
IRQ numbers. The goal is to get rid of the irq number from the
handlers in the IRQ flow which is nice.
- Rob Herring killed off the set_irq_flags() for all GPIO drivers.
This was an ARM specific function that is replaced with the generic
irq_modify_status() where special flags are actually needed.
- When an OF node has a pin range for its GPIOs, return -EPROBE_DEFER
if the pin controller isn't available. Pretty logical, yet needed
to be fixed.
- If a driver using GPIOLIB_IRQCHIP has its own irq_*_resources call
back, then call these instead of the defaults provided by the
GPIOLIB.
- Fix an undocumented ABI hole: named GPIOs were not properly
documented.
Driver improvements:
- Add get_direction() support to the generic GPIO driver, it's
strange that we didn't have that before.
- Make it possible to have input-only GPIO chips using the generic
GPIO driver.
- Clean out platform data support from the Emma Mobile (EM) driver
- Finegrained runtime PM support for the RCAR driver.
- Support r8a7795 (R-car H3) in the RCAR driver.
- Support interrupts on GPIOs 16 thru 31 in the DaVinci driver.
- Some consolidation and new support in the MPC8xxx driver, we now
support MPC5125.
- Preempt-RT-friendly patches: the OMAP, MPC8xxx, drivers uses raw
spinlocks making it work better with the realime patches.
- Interrupt support for the EXTRAXFS GPIO driver.
- Make the ETRAXFS GPIO driver support also ARTPEC-3.
- Interrupt and wakeup support for the BRCMSTB driver, also for
wakeup from S5 cold boot.
- Mask MXC IRQs during suspend.
- Improve OMAP2 GPIO set_debounce() to work according to spec.
- The VF610 driver handles IRQs properly.
New drivers:
- ZTE ZX GPIO driver"
* tag 'gpio-v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (87 commits)
Revert "gpio: extraxfs: fix returnvar.cocci warnings"
gpio: tc3589x: use static container helper
gpio: xlp: fix error return code
gpio: vf610: handle level IRQ's properly
gpio: max732x: Fix error handling in probe()
gpio: omap: fix clk_prepare/unprepare usage
gpio: omap: protect regs access in omap_gpio_irq_handler
gpio: omap: fix omap2_set_gpio_debounce
gpio: omap: switch to use platform_get_irq
gpio: omap: remove wrong irq_domain_remove usage in probe
gpiolib: add description for gpio irqchip fields in struct gpio_chip
gpio: extraxfs: fix returnvar.cocci warnings
gpiolib: irqchip: use different lockdep class for each gpio irqchip
gpio/grgpio: fix deadlock in grgpio_irq_unmap()
Documentation: gpio: consumer: describe active low property
gpio: mxc: fix section mismatch warning
gpio/mxc: mask gpio interrupts in suspend
gpio: omap: Fix missing raw locks conversion
gpio: brcmstb: support wakeup from S5 cold boot
gpio: brcmstb: Add interrupt and wakeup source support
...
*) Add new NXP USB OTG PHY driver
*) Add vbus/id detection, extcon support and fixes in phy-sun4i-usb
driver
*) Add support to use phy-sun4i-usb driver for sun8i-a23 and sun8i-a33
SoCs
*) Other trivial code cleanups, dropping .owner assignment and constify
phy_ops
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=97xz
-----END PGP SIGNATURE-----
Merge tag 'phy-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 4.3
*) Add new NXP USB OTG PHY driver
*) Add vbus/id detection, extcon support and fixes in phy-sun4i-usb
driver
*) Add support to use phy-sun4i-usb driver for sun8i-a23 and sun8i-a33
SoCs
*) Other trivial code cleanups, dropping .owner assignment and constify
phy_ops
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Changing the frequency of the USB clock must be done before the
PLL is powered on (prepared). This matters when the USB clock
is not setup by either boot ROM or boot loader. Reorder the
function calls to adhere to the order noted in the user manual.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The phy_ops variables are never modified after initialized in these
drivers, so make them const.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The ops is never changed in ulpi_phy_create(), so make it const.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
data->vbus_det is always 1 on boards without a (working) vbus-det, skip
the vbus_det test on such boards.
This fixes the sun4i usb phy code never turning on Vbus on such boards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Move vbus-detect helper functions up in the file, just moving some code
around, no functional changes what so ever.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
SATA_PLL_SOFT_RESET bit of CTRL_CORE_SMA_SW_0 must be toggled
between a SATA DPLL unlock and re-lock to prevent SATA lockup.
Introduce a new DT parameter 'syscon-pllreset' to provide the syscon
regmap access to this register which sits in the control module.
If the register is not provided we fallback to the old behaviour
i.e. SATA DPLL refclk will not be disabled and we prevent SoC low
power states.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
sun4i_usb_phy_set_squelch_detect is used by other code, which may be built
as a module, so it should be exported.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
platform_driver does not need to set an owner because
platform_driver_register() will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Remove unneeded space after tab.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
copy and paste error from berlin sata phy driver.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
There was big cleanup in past to remove this unneeded setting.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
On some boards there is no vbus_det gpio pin, instead vbus-detection for
otg can be done via the pmic.
This commit adds support for monitoring vbus_det via the power_supply
exported by the pmic, enabling support for otg on these boards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
On some boards we cannot detect the presence of an external Vusb, because
e.g. the 5V of the otg connector is directly connected to the 5V of the board,
and thus is always high.
This commit adds support for using such boards by only looking at the
id-detection pin.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The usb-phys on the sun8i-a33 SoC are mostly the same as sun8i-a23 but for
some reason (hw bug?) the phyctl register was moved to a different address
and is not initialized to 0 on reset.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The usb-phys on the sun8i-a23 SoC have the same setup wrt clocks as on the
sun6i-a31 SoC, but there are only 2 instead of 3 like on the sun5i-a13 SoC.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Before this commit the code for determining the disconnect threshold was
checking for "allwinner,sun4i-a10-usb-phy" or "allwinner,sun6i-a31-usb-phy"
assuming that those where the exception and then newer SoCs would use a
disconnect threshold of 2 like sun7i does. But it turns out that newer
SoCs use a disconnect threshold of 3 and sun5i and sun7i are the
exceptions, so check for those instead.
Here are the settings from the various Allwinner SDK sources:
sun4i-a10: USBC_Phy_Write(usbc_no, 0x2a, 3, 2);
sun5i-a13: USBC_Phy_Write(usbc_no, 0x2a, 2, 2);
sun6i-a31: USBC_Phy_Write(usbc_no, 0x2a, 3, 2);
sun7i-a20: USBC_Phy_Write(usbc_no, 0x2a, 2, 2);
sun8i-a23: USBC_Phy_Write(usbc_no, 0x2a, 3, 2);
sun8i-h3: USBC_Phy_Write(usbc_no, 0x2a, 3, 2);
sun9i-a80: USBC_Phy_Write(usbc_no, 0x2a, 3, 2);
Note this commit makes no functional changes as currently we only support
sun4i - sun7i.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The sunxi musb glue needs to know if a host or normal usb cable is plugged
in, add extcon support so that the musb glue can monitor the host status.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The usb0 phy is connected to an OTG controller, and as such needs some special
handling:
1) It allows explicit control over the pullups, enable these on phy_init and
disable them on phy_exit.
2) It has bits to signal id and vbus detect to the musb-core, add support for
for monitoring id and vbus detect gpio-s for use in dual role mode, and set
these bits to the correct values for operating in host only mode when no
gpios are specified in the devicetree.
While updating the devicetree binding documentation also add documentation
for the sofar undocumented usage of regulators for vbus for all 3 phys.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add PHY driver for the internal USB OTG PHY found on NXP
LPC18xx and LPC43xx devices. This driver takes care of
enabling the PHY in CREG (syscon) and setting the required
clock frequency.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The USB PLL divider set by the marvell,berlin2-usb-phy compatible is not
correct for BG2. We couldn't change it before because BG2Q incorrectly
used the same compatible string. Now that BG2Q's compatible is fixed,
change BG2's divider to the correct value.
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Tested-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The marvell,berlin2cd-usb-phy compatible incorrectly sets the PLL
divider to BG2's value instead of BG2CD/BG2Q's. Change it to the right
value.
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Fix this compile error:
drivers/built-in.o: In function 'mv_usb2_phy_probe':
phy-pxa-28nm-usb2.c:(.text+0x25ec): undefined reference to
'devm_ioremap_resource'
drivers/built-in.o: In function 'mv_hsic_phy_probe':
phy-pxa-28nm-hsic.c:(.text+0x3084): undefined reference to
'devm_ioremap_resource'
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Relying on PM-ops for shutting down PHY clocks was a
bad idea since the users (e.g. PCIe/SATA) might not
have been suspended by then.
The main culprit for not shutting down the clocks was
the stray pm_runtime_get() call in probe.
Fix the whole thing in the right way by getting rid
of that pm_runtime_get() call from probe and
removing all PM-ops. It is the sole responsibility
of the PHY user to properly turn OFF and de-initialize
the PHY as part of its suspend routine.
As PHY core serializes init/exit we don't need
to use a spinlock in this driver. So get rid of it.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.
Furthermore there is devm_gpiod_get_optional which is designed to get
optional gpios.
Simplify driver accordingly.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Pull MIPS updates from Ralf Baechle:
- Improvements to the tlb_dump code
- KVM fixes
- Add support for appended DTB
- Minor improvements to the R12000 support
- Minor improvements to the R12000 support
- Various platform improvments for BCM47xx
- The usual pile of minor cleanups
- A number of BPF fixes and improvments
- Some improvments to the support for R3000 and DECstations
- Some improvments to the ATH79 platform support
- A major patchset for the JZ4740 SOC adding support for the CI20 platform
- Add support for the Pistachio SOC
- Minor BMIPS/BCM63xx platform support improvments.
- Avoid "SYNC 0" as memory barrier when unlocking spinlocks
- Add support for the XWR-1750 board.
- Paul's __cpuinit/__cpuinitdata cleanups.
- New Malta CPU board support large memory so enable ZONE_DMA32.
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (131 commits)
MIPS: spinlock: Adjust arch_spin_lock back-off time
MIPS: asmmacro: Ensure 64-bit FP registers are used with MSA
MIPS: BCM47xx: Simplify handling SPROM revisions
MIPS: Cobalt Don't use module_init in non-modular MTD registration.
MIPS: BCM47xx: Move NVRAM driver to the drivers/firmware/
MIPS: use for_each_sg()
MIPS: BCM47xx: Don't select BCMA_HOST_PCI
MIPS: BCM47xx: Add helper variable for storing NVRAM length
MIPS: IRQ/IP27: Move IRQ allocation API to platform code.
MIPS: Replace smp_mb with release barrier function in unlocks.
MIPS: i8259: DT support
MIPS: Malta: Basic DT plumbing
MIPS: include errno.h for ENODEV in mips-cm.h
MIPS: Define GCR_GIC_STATUS register fields
MIPS: BPF: Introduce BPF ASM helpers
MIPS: BPF: Use BPF register names to describe the ABI
MIPS: BPF: Move register definition to the BPF header
MIPS: net: BPF: Replace RSIZE with SZREG
MIPS: BPF: Free up some callee-saved registers
MIPS: Xtalk: Update xwidget.h with known Xtalk device numbers
...
Here's the big USB patchset for 4.2-rc1. As is normal these days, the
majority of changes are in the gadget drivers, with a bunch of other
small driver changes.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlWNobIACgkQMUfUDdst+ylXtQCgwTnzFBzly+3h1Npa2CWkr/Lw
TWAAn31qEP28MLjm8iVJLNPwdVd2kt1w
=hrdz
-----END PGP SIGNATURE-----
Merge tag 'usb-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here's the big USB patchset for 4.2-rc1. As is normal these days, the
majority of changes are in the gadget drivers, with a bunch of other
small driver changes.
All of these have been in linux-next with no reported issues"
* tag 'usb-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (175 commits)
usb: dwc3: Use ASCII space in Kconfig
usb: chipidea: add work-around for Marvell HSIC PHY startup
usb: chipidea: allow multiple instances to use default ci_default_pdata
dt-bindings: Consolidate ChipIdea USB ci13xxx bindings
phy: add Marvell HSIC 28nm PHY
phy: Add Marvell USB 2.0 OTG 28nm PHY
dt-bindings: Add Marvell PXA1928 USB and HSIC PHY bindings
USB: ssb: use devm_kzalloc
USB: ssb: fix error handling in ssb_hcd_create_pdev()
usb: isp1760: check for null return from kzalloc
cdc-acm: Add support of ATOL FPrint fiscal printers
usb: chipidea: usbmisc_imx: Remove unneeded semicolon
USB: usbtmc: add device quirk for Rigol DS6104
USB: serial: mos7840: Use setup_timer
phy: twl4030-usb: add ABI documentation
phy: twl4030-usb: remove incorrect pm_runtime_get_sync() in probe function.
phy: twl4030-usb: remove pointless 'suspended' test in 'suspend' callback.
phy: twl4030-usb: make runtime pm more reliable.
drivers:usb:fsl: Fix compilation error for fsl ehci drv
usb: renesas_usbhs: Don't disable the pipe if Control write status stage
...
Mohit's email-id doesn't exist anymore as he has left the company.
Replace ST's id with mohit.kumar.dhaka@gmail.com.
Signed-off-by: Pratyush Anand <pratyush.anand@gmail.com>
Cc: Mohit Kumar <mohit.kumar.dhaka@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
pratyush.anand@st.com email-id doesn't exist anymore as I have left the
company. Replace ST's id with pratyush.anand@gmail.com.
Signed-off-by: Pratyush Anand <pratyush.anand@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add PHY driver for the Marvell HSIC 28nm PHY. This PHY is found in PXA1928
SOC.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add driver for USB 28nm PHY found in Marvell PXA1928 SOC.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This resolves a merge issue in musb_core.c and we want the fixes that
were in Linus's tree in this branch as well for testing.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
*) new Broadcom SATA3 PHY driver for Broadcom STB SoCs
*) new phy API to get PHY by index which is used in EHCI and
OHCI controller drivers
*) support specifying supply at port level used for multi-port PHYs
*) sparse warning fixes in miphy PHYs
*) fix pm_runtime issues in twl4030 driver
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=vPk6
-----END PGP SIGNATURE-----
Merge tag 'phy-for-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 4.2 merge window
*) new Broadcom SATA3 PHY driver for Broadcom STB SoCs
*) new phy API to get PHY by index which is used in EHCI and
OHCI controller drivers
*) support specifying supply at port level used for multi-port PHYs
*) sparse warning fixes in miphy PHYs
*) fix pm_runtime issues in twl4030 driver
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The USB phy should initialize with power-off, and will be powered on
by the USB system when a cable connection is detected.
Having this pm_runtime_get_sync() during probe causes the phy to
*always* be powered on.
Removing it returns to sensible power management.
Fixes: 96be39ab34
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
When the runtime_suspend callback is running, 'runtime_status'
is always RPM_SUSPENDING, so pm_runtime_suspended() will always
fail.
Similarly while the runtime_resume callback is running
'runtime_status' is RPM_RESUMING, so pm_runtime_active() will
always fail.
So remove these two pointless tests.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
A construct like:
if (pm_runtime_suspended(twl->dev))
pm_runtime_get_sync(twl->dev);
is against the spirit of the runtime_pm interface as it
makes the internal refcounting useless.
In this case it is also racy, particularly as 'put_autosuspend'
is used to drop a reference.
When that happens a timer is started and the device is
runtime-suspended after the timeout.
If the above code runs in this window, the device will not be
found to be suspended so no pm_runtime reference is taken.
When the timer expires the device will be suspended, which is
against the intention of the code.
So be more direct is taking and dropping references.
If twl->linkstat is VBUS_VALID or ID_GROUND, then hold a
pm_runtime reference, otherwise don't.
Define "cable_present()" to test for this condition.
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The sunxi otg phy has a bug where it wrongly detects a high speed squelch
when reset on the root port gets de-asserted with a lo-speed device.
The workaround for this is to disable squelch detect before de-asserting
reset, and re-enabling it after the reset de-assert is done. Add a sunxi
specific phy function to allow the sunxi-musb glue to do this.
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Supports up to two ports which can each be powered on/off and configured
independently.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch adds a compatible string to support for R-Car E2.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
TUSB1210 ULPI PHY has vendor specific register for eye
diagram tuning. On some platforms the system firmware has
set optimized value to it. In order to not loose the
optimized value, the driver stores it during probe and
restores it every time the PHY is powered back on.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
ULPI PHYs need to be bound to their controllers with a
lookup. This adds helpers that the ULPI drivers can use to
do both, the registration of the PHY and the lookup, at the
same time.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
According to the technical update (No. TN-RCS-B011A/E), the UGSTS LOCK
bit location is bit 8, not bits 1 and 0. It also says that the register
address offset of UGSTS is 0x88, not 0x90.
So, this patch fixes the USBHS_UGSTS_LOCK value and some comments.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
if devm_clk_get for wkupclk fails, there will be an unbalanced
pm_runtime_enable. Fix it here.
Reported-by: Benoit Parrot <bparrot@ti.com>
Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
DM816x PHY uses usb_phy_* methods and because
of that, it must select USB_PHY, however, because
the drivers in question (DM816x, TWL4030 and
OMAP_USB2) sit outside of drivers/usb/ directory,
meaning they can be built even if USB_SUPPORT=n.
This patches fixes the dependencies by adding
USB_SUPPORT as a dependency and making all drivers
select USB_PHY (which cannot be selected through
menuconfig).
Note that this fixes some linking breakages when
building with randconfig.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This phy only exists on platforms under ARCH_QCOM, not ARCH_MSM.
Cc: Yaniv Gardi <ygardi@codeaurora.org>
Cc: Dov Levenglick <dovl@codeaurora.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: David Brown <davidb@codeaurora.org>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This is a common checking in various drivers, so move the checking to
_of_phy_get().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add missing 'static' modifier so sparse
won't complain anymore.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add missing __iomem annotation to the base address
so Sparse doesn't complain.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Multi-port phys may have per port power supplies. Let's change phy
core to look for supply at the port level when multiple ports are
specified. To keep compatibility with the existing device tree board
descriptions for single-port phys we will continue looking up the
power supply at the parent node level
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Arun Ramamurthy <arun.ramamurthy@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Some generic drivers, such as ehci, may use multiple phys and for such
drivers referencing phy(s) by name(s) does not make sense. Instead of
inventing new naming schemes and using custom code to iterate through them,
such drivers are better of using nameless phy bindings and using this newly
introduced API to iterate through them.
Signed-off-by: Arun Ramamurthy <arun.ramamurthy@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
[kishon@ti.com: fix compilation errors]
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Don't pass valid pointer to PTR_ERR, use PTR_ERR(phy) only when
IS_ERR(phy) is true.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Here's the big USB (and PHY) driver patchset for 4.1-rc1.
Everything here has been in linux-next, and the full details are below
in the shortlog. Nothing major, just the normal round of new
drivers,api updates, and other changes, mostly in the USB gadget area,
as usual.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlUsHXYACgkQMUfUDdst+ykGvwCfbI3z0VYJqyvPi7pbn+jtGouQ
E7MAoICdP90ofZfyzQzXy+2xKTTCiP5L
=jSjh
-----END PGP SIGNATURE-----
Merge tag 'usb-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB driver updates from Greg KH:
"Here's the big USB (and PHY) driver patchset for 4.1-rc1.
Everything here has been in linux-next, and the full details are below
in the shortlog. Nothing major, just the normal round of new
drivers,api updates, and other changes, mostly in the USB gadget area,
as usual"
* tag 'usb-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (252 commits)
drivers/usb/core: devio.c: Removed an uneeded space before tab
usb: dwc2: host: sleep USB_RESUME_TIMEOUT during resume
usb: chipidea: debug: add low power mode check before print registers
usb: chipidea: udc: bypass pullup DP when gadget connect in OTG fsm mode
usb: core: hub: use new USB_RESUME_TIMEOUT
usb: isp1760: hcd: use new USB_RESUME_TIMEOUT
usb: dwc2: hcd: use new USB_RESUME_TIMEOUT
usb: host: sl811: use new USB_RESUME_TIMEOUT
usb: host: r8a66597: use new USB_RESUME_TIMEOUT
usb: host: oxu210hp: use new USB_RESUME_TIMEOUT
usb: host: fusbh200: use new USB_RESUME_TIMEOUT
usb: host: fotg210: use new USB_RESUME_TIMEOUT
usb: host: isp116x: use new USB_RESUME_TIMEOUT
usb: musb: use new USB_RESUME_TIMEOUT
usb: host: uhci: use new USB_RESUME_TIMEOUT
usb: host: ehci: use new USB_RESUME_TIMEOUT
usb: host: xhci: use new USB_RESUME_TIMEOUT
usb: define a generic USB_RESUME_TIMEOUT macro
usb: musb: dsps: fix build on i386 when COMPILE_TEST is set
ehci-hub: use USB_DT_HUB
...
============
*) Add driver for USB PHYs on sun9i
*) Add driver for USB PHY on dm816x
*) Modified exynos5-usbdrd driver to add support for Exynos5433 SoC
Fixes
=====
*) Fix power_on/power_off failure paths in some drivers
*) Make miphy365x use generic PHY type constants
*) Fix build errors due to missing export symbols in qcom-ufs driver
*) Make all the functions return proper error values
Cleanups
========
*) use PTR_ERR_OR_ZERO to simplify code
*) use devm_kcalloc instead of devm_kzalloc with multiply
*) remove un-necessary ifdef CONFIG_OF
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=0gB+
-----END PGP SIGNATURE-----
Merge tag 'for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
New Features
============
*) Add driver for USB PHYs on sun9i
*) Add driver for USB PHY on dm816x
*) Modified exynos5-usbdrd driver to add support for Exynos5433 SoC
Fixes
=====
*) Fix power_on/power_off failure paths in some drivers
*) Make miphy365x use generic PHY type constants
*) Fix build errors due to missing export symbols in qcom-ufs driver
*) Make all the functions return proper error values
Cleanups
========
*) use PTR_ERR_OR_ZERO to simplify code
*) use devm_kcalloc instead of devm_kzalloc with multiply
*) remove un-necessary ifdef CONFIG_OF
The of_xlate callback should return ERR_PTR on error.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The of_xlate callback should return ERR_PTR on error.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Now there are generic phy type constants declared in phy.h, migrate over to
using them rather than defining our own. This change has been done as one
atomic commit to be bisectable.
Note: The values of the defines are the same, so there is no ABI breakage
with this patch.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Unlike previous Allwinner SoCs, there is no central PHY control block
on the A80. Also, OTG support is completely split off into a different
controller.
This adds a new driver to support the regular USB PHYs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add a minimal driver for dm816x USB. This makes USB work on dm816x
without any other changes needed as it can use the existing musb_dsps
glue layer for the USB controller.
Note that this phy is different from dm814x and am335x.
Cc: Bin Liu <binmlist@gmail.com>
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Cc: Paul Bolle <pebolle@tiscali.nl>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
"dev_ref_clk_ctrl_mem" is optional resource, so don't return error if fail to
get the resource. Since it's an optional resource, don't emit error if
fail to get dev_ref_clk_ctrl_mem.
Also remove redundant test for res, it's done by devm_ioremap_resource().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Ensure we have balanced clk_prepare_enable/clk_disable_unprepare calls if
.power_on or .power_off callbacks return error.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch adds driver data to support for Exynos5433 SoC.
The Exynos5433 has one USB3.0 Host and USB3.0 DRD(Dual Role Device).
Exynos5433 is simplar to Eyxnos7 but Exynos5433 have
one more USB3.0 Host controller.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Current code does NULL test against return value of ufs_qcom_phy_generic_probe.
However, in the case of devm_phy_create() failure, ufs_qcom_phy_generic_probe
does not return NULL. Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
If stih41x_usb_phy_power_on() fails, we need to call clk_disable_unprepare()
before return error. This is to ensure we have balanced clk_enable/disable
calls.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Current code does not call clk_prepare(phy->optclk) when using the old
usb_otg_ss_refclk960m name. Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Remove extra space in MODULE_ALIAS.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
When phy_pm_runtime_get_sync() returns -ENOTSUPP, phy_exit() also returns
-ENOTSUPP if !phy->ops->exit. Fix it.
Also move the code to override ret close to the code we got ret.
I think it is less error prone this way.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Prefer devm_kcalloc over devm_kzalloc with multiply.
In additional, use sizeof(phy) is incorrect, fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Gabriel Fernandez<gabriel.fernandez@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Prefer devm_kcalloc over devm_kzalloc with multiply.
In additional, use sizeof(phy) is incorrect, fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Current code uses args->args[0] as array subscript of phy_drd->phys[].
So the valid value range for args->args[0] is 0 ... EXYNOS5_DRDPHYS_NUM - 1.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
devm_phy_create() stores the pointer to the new PHY at the address
returned by devres_alloc(). The res parameter passed to devm_phy_match()
is therefore the location where the pointer to the PHY is stored, hence
it needs to be dereferenced before comparing to the match data in order
to find the correct match.
Cc: <stable@vger.kernel.org> # v3.13+
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
If rockchip_usb_phy_power() fails, we need to call clk_disable_unprepare()
before return. This is to ensure we have balanced clk_enable/disable calls.
Also remove unneeded ret checking in rockchip_usb_phy_power_off.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Code simplification. No functional change.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Current code uses num_phys settings to tell the number of entries in phys.
Thus remove the NULL terminating entry from phys array which is not necessary.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This prevent NULL pointer dereference if res is NULL.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
If IS_ERR(state->regs) the .probe fails.
So IS_ERR(state->regs) test in exynos_dp_video_phy_pwr_isol() is not necessary.
exynos_dp_video_phy_pwr_isol() simply does a regmap_update_bits() call now,
just call regmap_update_bits() instead and return proper return value.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The state->regmap is initialized by devm_regmap_init_mmio().
So it's fine to use spin_lock rather than mutex to protct state->regmap rmw
operations.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
[Julia.Lawall@lip6.fr: Found an issue with the original patch w.r.t unbalanced
spin_lock call]
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
At the context where we have pointer to struct phy, it's useful to call
phy_get_drvdata() to get the address of priv. With this change, we can
remove the to_phy_berlin_usb_priv() macro and remove *phy from struct
phy_berlin_usb_priv.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
if !CONFIG_OF, the probe fails.
This is a dt-only driver, so the ifdef CONFIG_OF guard and of_match_ptr are
not needed.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
if !CONFIG_OF, the probe fails.
This is a dt-only driver, so the ifdef CONFIG_OF guard and of_match_ptr are
not needed.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
if !CONFIG_OF, the probe fails.
This is a dt-only driver, so the ifdef CONFIG_OF guard and of_match_ptr are
not needed.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
PTR_ERR_OR_ZERO simplifies the code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Gabriel Fernandez<gabriel.fernandez@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Prefer devm_kcalloc over devm_kzalloc with multiply.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
syscon_regmap_lookup_by_phandle() returns ERR_PTR on error.
Thus don't use null test against state->regmap.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add missing .owner field in miphy28lp_ops, which is used for refcounting.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Set it once is enough and it's done after devm_kzalloc().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
At the context we have pointer to struct phy, it's useful to call
phy_get_drvdata() to get the address of cluster_phy. This has slightly
better readability than calling dev_get_drvdata(phy->dev.parent).
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Currently, of_get_child_count() is called in each iteration of the for loop in
miphy365x_xlate(). This patch stores the return value of of_get_child_count()
in miphy_dev->nphys and call of_get_child_count() once in miphy365x_probe().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Currently, of_get_child_count() is called in each iteration of the for loop in
miphy28lp_xlate(). This patch stores the return value of of_get_child_count()
in miphy_dev->nphys and call of_get_child_count() once in miphy28lp_probe().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Here's the big pull request for the USB driver tree for 3.20-rc1.
Nothing major happening here, just lots of gadget driver updates, new
device ids, and a bunch of cleanups.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlTgtrcACgkQMUfUDdst+yn0tACgygJPNvu1l3ukNJCCpWuOErIj
3KsAnjiEXv90DLYJiVLJ4EbLPw0V9wAv
=DrJx
-----END PGP SIGNATURE-----
Merge tag 'usb-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg KH:
"Here's the big pull request for the USB driver tree for 3.20-rc1.
Nothing major happening here, just lots of gadget driver updates, new
device ids, and a bunch of cleanups.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (299 commits)
usb: musb: fix device hotplug behind hub
usb: dwc2: Fix a bug in reading the endpoint directions from reg.
staging: emxx_udc: fix the build error
usb: Retry port status check on resume to work around RH bugs
Revert "usb: Reset USB-3 devices on USB-3 link bounce"
uhci-hub: use HUB_CHAR_*
usb: kconfig: replace PPC_OF with PPC
ehci-pci: disable for Intel MID platforms (update)
usb: gadget: Kconfig: use bool instead of boolean
usb: musb: blackfin: remove incorrect __exit_p()
USB: fix use-after-free bug in usb_hcd_unlink_urb()
ehci-pci: disable for Intel MID platforms
usb: host: pci_quirks: joing string literals
USB: add flag for HCDs that can't receive wakeup requests (isp1760-hcd)
USB: usbfs: allow URBs to be reaped after disconnection
cdc-acm: kill unnecessary messages
cdc-acm: add sanity checks
usb: phy: phy-generic: Fix USB PHY gpio reset
usb: dwc2: fix USB core dependencies
usb: renesas_usbhs: fix NULL pointer dereference in dma_release_channel()
...
This is the usual grab bag of driver updates (hpsa, storvsc, mp2sas,
megaraid_sas, ses) plus an assortment of minor updates. There's also an
update to ufs which adds new phy drivers and finally a new logging
infrastructure for SCSI.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJU2Ty5AAoJEDeqqVYsXL0M9rAH/1xNpAxXuxQq+dW5Z+uOaX60
5RRIu7/xA1HEfzkT5FTHrolmogDjVqawu4PZS66iHDeo05RBVUlbTA8qCK+MlRcN
U6s0cLEw59eH3EaCfOGuYp/MnbhuV0eNxe0btmqJIQwuW3+gwZKGJdOq6LS2YasJ
k/DyIBVmkJAVsN56vm9q2vbtcZp+Bg+ngqBS+SC4TF7vV1WCtFmS6yaUf62PYW3D
+Irx37qHZntDR5wdw3dsuKDi5U8bl6myPjaVLnVJqg/WIF9RlCkjk5xpWT99AmVO
NmtYQxLLBlAQ5K+sIlBUwxZe+8q1l+Aj4TTmJHAfFtyfp25s7JR9I6/QtOyC5Kw=
=odol
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull first round of SCSI updates from James Bottomley:
"This is the usual grab bag of driver updates (hpsa, storvsc, mp2sas,
megaraid_sas, ses) plus an assortment of minor updates.
There's also an update to ufs which adds new phy drivers and finally a
new logging infrastructure for SCSI"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (114 commits)
scsi_logging: return void for dev_printk() functions
scsi: print single-character strings with seq_putc
scsi: merge consecutive seq_puts calls
scsi: replace seq_printf with seq_puts
aha152x: replace seq_printf with seq_puts
advansys: replace seq_printf with seq_puts
scsi: remove SPRINTF macro
sg: remove an unused variable
hpsa: Use local workqueues instead of system workqueues
hpsa: add in P840ar controller model name
hpsa: add in gen9 controller model names
hpsa: detect and report failures changing controller transport modes
hpsa: shorten the wait for the CISS doorbell mode change ack
hpsa: refactor duplicated scan completion code into a new routine
hpsa: move SG descriptor set-up out of hpsa_scatter_gather()
hpsa: do not use function pointers in fast path command submission
hpsa: print CDBs instead of kernel virtual addresses for uncommon errors
hpsa: do not use a void pointer for scsi_cmd field of struct CommandList
hpsa: return failed from device reset/abort handlers
hpsa: check for ctlr lockup after command allocation in main io path
...
Based on Arnds review comments here https://lkml.org/lkml/2014/11/13/161,
update the miphy365 phy driver to access sysconfig register offsets via
syscfg dt property.
This is because the reg property should not be mixing address spaces
like it does currently for miphy365. This change then also aligns us
to how other platforms such as keystone and bcm7445 pass there syscon
offsets via DT.
This patch breaks DT compatibility, but this platform is considered WIP,
and is only used by a few developers who are upstreaming support for it.
This change has been done as a single atomic commit to ensure it is
bisectable.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Tested-by: Maxime Coquelin <maxime.coquelin@st.com>
After the Exynos Power Management Unit (PMU) driver was converted
to the platform device driver in commit 14fc8b93d4
("ARM: EXYNOS: Add platform driver support for Exynos PMU") and
then PMU device nodes added to Exynos4 DTs in commit
7b9613aca4 ("ARM: dts: add PMU syscon node for exynos4")
the mipi video phy driver started failing probing, due to overlapping
memory mapped register region resources.
Now all the Exynos peripheral devices which have registers in the PMU
region are supposed to use the regmap provided by the syscon driver.
So support for regmap is added in this patch, this unfortunately
creates yet another indirection into that supposedly trivial driver.
The additional mutex is required because single register is used by
PHY pairs (they share bit in a register). An improvement here could
be to allow a PHY instance be created with a driver custom mutex,
which would then be common for each PHY pair. This would eliminate
one of 3 mutexes which need to be taken in the phy_power_on/
phy_power_off code path. However, I tried to keep this bug fix patch
possibly simple.
This change is needed to make MIPI DSI displays and MIPI CSI-2
camera sensors working again on Exynos4 boards.
Cc: Pankaj Dubey <pankaj.dubey@samsung.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch to add a generic PHY driver for ROCKCHIP usb PHYs,
currently this driver can support RK3288. The RK3288 SoC have
three independent USB PHY IPs which are all configured through a
set of registers located in the GRF (general register files)
module.
Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Conflicts:
arch/arm/boot/dts/imx6sx-sdb.dts
net/sched/cls_bpf.c
Two simple sets of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on Arnds review comments here https://lkml.org/lkml/2014/11/13/161,
update the phy driver to not use the reg property to access the sysconfig
register offsets.
This is because other phy's (miphy28, miphy365) have a combination of
memory mapped registers and sysconfig control regs, and we shouldn't
be mixing address spaces in the reg property. In addition we would
ideally like the sysconfig offsets to be passed via DT in a uniform way.
This new method will also allow us to support devices which have sysconfig
registers in different banks more easily and it is also analagous to how
keystone and bcm7745 platforms pass there syscon offsets in DT.
This breaks DT compatibility, but this platform is considered WIP, and
is only used by a few developers who are upstreaming support for it.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Based on Arnds review comments here https://lkml.org/lkml/2014/11/13/161,
update the miphy28lp phy driver to access sysconfig register offsets via
syscfg dt property.
This is because the reg property should not be mixing address spaces like
it does currently for miphy28lp. This change then also aligns us to how other
platforms such as keystone and bcm7445 pass there syscon offsets via DT.
I have updated the miphy28lp phy driver same way as Peter's implementation.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
In case of error, the function devm_ioremap_resource() returns
ERR_PTR() and never returns NULL. The NULL test in the return
value check should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Failed test case: Boot without SATA drive connected. Suspend/resume
the board and then connect SATA drive. It fails to enumerate.
Due to Errata i783 "SATA Lockup After SATA DPLL Unlock/Relock"
we can't allow SATA DPLL to be in the unlocked state.
The SATA refclk (sata_ref_clk) is the source of the SATA_DPLL.
This clock is being controlled only by the AHCI SATA driver and is
shut off during system suspend (if the SATA drive was not already attached)
causing the SATA DPLL to be unlocked and so causing errata i783.
To prevent sata_ref_clk from being disabled, we add the control of
this clock to the SATA PHY driver and prevent it from being disabled.
This also fixes the issue of SATA not working on OMAP5/DRA7 when
AHCI platform driver is built as a module.
NOTE: Device tree changes also required for OMAP5 & DRA7.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
On system suspend, the runtime_suspend() driver hook doesn't get
called for USB phy and so the clocks are not disabled in the driver.
This causes the L3INIT_960M_GFCLK and L3INIT_480M_GFCLK to remain
active on the DRA7 platform while in system suspend.
In case of pcie-phy, the runtime_suspend hook gets called after
the suspend hook so we introduce a flag phy->enabled to keep
track if our clocks are enabled or not to prevent multiple
enable/disables.
Add suspend/resume hooks to the driver.
Move enabling/disabling clock code into helper functions.
Reported-by: Nishant Menon <nm@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This change adds a support for a 14nm qcom-ufs phy that is
required in platforms that use ufs-qcom controller.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: Dov Levenglick <dovl@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This change adds a support for a 20nm qcom-ufs phy that is required in
platforms that use ufs-qcom controller.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: Dov Levenglick <dovl@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This change adds a generic and common API support for ufs phy QUALCOMM
Technologies. This support provides common code and also points
to specific phy callbacks to differentiate between different behaviors
of frequent use-cases (like power on, power off, phy calibration etc).
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: Dov Levenglick <dovl@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Based on Arnds review comments here https://lkml.org/lkml/2014/11/13/161,
update the miphy365 phy driver to access sysconfig register offsets via
syscfg dt property.
This is because the reg property should not be mixing address spaces
like it does currently for miphy365. This change then also aligns us
to how other platforms such as keystone and bcm7445 pass there syscon
offsets via DT.
This patch breaks DT compatibility, but this platform is considered WIP,
and is only used by a few developers who are upstreaming support for it.
This change has been done as a single atomic commit to ensure it is
bisectable.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on Arnds review comments here https://lkml.org/lkml/2014/11/13/161,
update the phy driver to not use the reg property to access the sysconfig
register offsets.
This is because other phy's (miphy28, miphy365) have a combination of
memory mapped registers and sysconfig control regs, and we shouldn't
be mixing address spaces in the reg property. In addition we would
ideally like the sysconfig offsets to be passed via DT in a uniform way.
This new method will also allow us to support devices which have sysconfig
registers in different banks more easily and it is also analagous to how
keystone and bcm7745 platforms pass there syscon offsets in DT.
This breaks DT compatibility, but this platform is considered WIP, and
is only used by a few developers who are upstreaming support for it.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to DRA74x silicon rev 1.1, pcie_pcs register bits 8-15 and bits 16-23
were used to configure RC delay count for phy1 and phy2 respectively.
phyid was used as index to distinguish the phys and to configure the delay
values appropriately.
As of DRA74x silicon rev 1.1, pcie_pcs register definition has changed.
Bits 16-23 are used to configure delay values for *both* phy1 and phy2.
Hence phyid is no longer required.
So, drop id field from ti_pipe3 structure and its subsequent references
for configuring pcie_pcs register.
Also, pcie_pcs register now needs to be configured with delay value of 0x96
at bit positions 16-23. See register description of CTRL_CORE_PCIE_PCS in
ARM572x TRM, SPRUHZ6, October 2014, section 18.5.2.2, table 18-1804.
This is needed to ensure Gen2 cards are enumerated consistently.
DRA72x silicon behaves same way as DRA74x rev 1.1 as far as this functionality
is considered.
Test results on DRA74x and DRA72x EVMs:
Before patch
------------
DRA74x ES 1.0: Gen1 cards work, Gen2 cards do not work (expected result due to
silicon errata)
DRA74x ES 1.1: Gen1 cards work, Gen2 cards do not work sometimes due to incorrect
programming of register
DRA72x: Gen1 cards work, Gen2 cards do not work sometimes due to incorrect
programming of register
After patch
-----------
DRA74x ES 1.0: Gen1 cards work, Gen2 cards do not work (expected result due to
silicon errata)
DRA74x ES 1.1: Gen1 cards work, Gen2 cards work consistently.
DRA72x: Gen1 and Gen2 cards enumerate consistently.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The allwinner SDK uses a value of 3 for the disconnect threshold setting on
sun6i, do the same in the kernel.
In my previous experience with sun5i problems getting the threshold right
is important to avoid usb2 devices being unplugged sometimes going unnoticed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
We need to unlock before returning the -EINVAL here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by
the driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken
into account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should
have used from the start and drop some other unuseful KERN_ERR
messages printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool
(Prarit Bhargava).
- Fix two regressions introduced by recent commits in the OPP
library and clean up some existing minor issues in that code
(Viresh Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout
the tree (or drop it where that can be done) in order to make
it possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki,
Ulf Hansson, Ludovic Desroches). There will be one more
"CONFIG_PM_RUNTIME removal" batch after this one, because some
new uses of it have been introduced during the current merge
window, but that should be sufficient to finally get rid of it.
- Make the ACPI EC driver more robust against race conditions
related to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to
disable GPEs that it has not enabled which confuses ACPICA
and makes it report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver
to make it possible to override the blacklisting of some
systems in that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS
entry for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces
witn names that reflect the IDs of the ACPI device objects
they are associated with, except for "generic" ACPI fans
(PNP ID "PNP0C0B"). That's necessary for user space thermal
management tools to be able to connect the fans with the
parts of the system they are supposed to be cooling properly.
From Srinivas Pandruvada.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5fo2
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
"These are regression fixes (leds-gpio, ACPI backlight driver,
operating performance points library, ACPI device enumeration
messages, cpupower tool), other bug fixes (ACPI EC driver, ACPI device
PM), some cleanups in the operating performance points (OPP)
framework, continuation of CONFIG_PM_RUNTIME elimination, a couple of
minor intel_pstate driver changes, a new MAINTAINERS entry for it and
an ACPI fan driver change needed for better support of thermal
management in user space.
Specifics:
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by the
driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken into
account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should have
used from the start and drop some other unuseful KERN_ERR messages
printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool (Prarit
Bhargava).
- Fix two regressions introduced by recent commits in the OPP library
and clean up some existing minor issues in that code (Viresh
Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout the
tree (or drop it where that can be done) in order to make it
possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki, Ulf
Hansson, Ludovic Desroches).
There will be one more "CONFIG_PM_RUNTIME removal" batch after this
one, because some new uses of it have been introduced during the
current merge window, but that should be sufficient to finally get
rid of it.
- Make the ACPI EC driver more robust against race conditions related
to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to disable
GPEs that it has not enabled which confuses ACPICA and makes it
report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver to
make it possible to override the blacklisting of some systems in
that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS entry
for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces witn
names that reflect the IDs of the ACPI device objects they are
associated with, except for "generic" ACPI fans (PNP ID "PNP0C0B").
That's necessary for user space thermal management tools to be able
to connect the fans with the parts of the system they are supposed
to be cooling properly. From Srinivas Pandruvada"
* tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
MAINTAINERS: add entry for intel_pstate
ACPI / video: update the skip case for acpi_video_device_in_dod()
power / PM: Eliminate CONFIG_PM_RUNTIME
NFC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
SCSI / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / EC: Fix unexpected ec_remove_handlers() invocations
Revert "tools: cpupower: fix return checks for sysfs_get_idlestate_count()"
tracing / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
x86 / PM: Replace CONFIG_PM_RUNTIME in io_apic.c
PM: Remove the SET_PM_RUNTIME_PM_OPS() macro
mmc: atmel-mci: use SET_RUNTIME_PM_OPS() macro
PM / Kconfig: Replace PM_RUNTIME with PM in dependencies
ARM / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
sound / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
phy / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
video / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tty / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / PM: Do not disable wakeup GPEs that have not been enabled
ACPI / utils: Drop error messages from acpi_evaluate_reference()
...
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM everywhere under
drivers/phy/.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
of non-dt boot. Adds three new PHY drivers using the PHY framework and some
miscellaneous fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=oo3u
-----END PGP SIGNATURE-----
Merge tag 'for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-testing
Kishon writes:
Improvements in phy-core specifically on PHY core finds the PHY in the case
of non-dt boot. Adds three new PHY drivers using the PHY framework and some
miscellaneous fixes and cleanups.
The Armada 375 SoC comes with an USB2 host and device controller and
an USB3 controller. The USB cluster control register allows to manage
common features of both USB controllers.
This commit adds a driver integrated in the generic PHY framework to
control this USB cluster feature.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
[ kishon@ti.com : Made it to use the updated devm_phy_create API and
soem cosmentic changes in Kconfig file.]
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: coccinelle/api/ptr_ret.cocci
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This time, a very pull request with 216 non-merge
commits. Most of the commits contained here are
sparse or coccinelle fixes ranging from missing
'static' to returning 0 in case of errors.
More importantly, we have the removal the now
unnecessary 'driver' argument to ->udc_stop().
DWC2 learned about Dual-Role builds. Users of
this IP can now have a single driver built for
host and device roles.
DWC3 got support for two new HW platforms: Exynos7
and AMD.
The Broadcom USB 3.0 Device Controller IP is now
supported and so is PLX USB338x, which means DWC3
has lost is badge as the only USB 3.0 peripheral
IP supported on Linux.
Thanks for Tony Lindgren's work, we can now have
a distro-like kernel where all MUSB glue layers
can be built into the same kernel (statically
or dynamically linked) and it'll work in PIO (DMA
will come probably on v3.20).
Other than these, the usual set of cleanups and
non-critical fixes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WYyZ
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.19 merge window
This time, a very pull request with 216 non-merge
commits. Most of the commits contained here are
sparse or coccinelle fixes ranging from missing
'static' to returning 0 in case of errors.
More importantly, we have the removal the now
unnecessary 'driver' argument to ->udc_stop().
DWC2 learned about Dual-Role builds. Users of
this IP can now have a single driver built for
host and device roles.
DWC3 got support for two new HW platforms: Exynos7
and AMD.
The Broadcom USB 3.0 Device Controller IP is now
supported and so is PLX USB338x, which means DWC3
has lost is badge as the only USB 3.0 peripheral
IP supported on Linux.
Thanks for Tony Lindgren's work, we can now have
a distro-like kernel where all MUSB glue layers
can be built into the same kernel (statically
or dynamically linked) and it'll work in PIO (DMA
will come probably on v3.20).
Other than these, the usual set of cleanups and
non-critical fixes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This PHY controller is also present on Exynos7 platform
in arch-exynos family.
So PHY_EXYNOS5_USBDRD should now depend on ARCH_EXYNOS.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Some Exynos boards have a separate regulator controlling a
Boost 5V supply which goes as input for VBUS regulator.
So adding a control for the same in driver, to enable
vbus supply on the port.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Exynos7 SoC has now separate gate control for 125MHz pipe3 phy
clock, as well as 60MHz utmi phy clock.
Additionally, separate gate control is available for the clock
used for ITP (Isochronous Transfer Packet) generation.
So get the same and control in the phy-exynos5-usbdrd driver.
Suggested-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The users of the old method are now converted to the new one.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
[ kishon@ti.com : made phy-berlin-usb.c and phy-miphy28lp.c to use the updated
devm_phy_create API.]
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Creates the lookup separately. Hard coding the consumer as
it can't be anything else except musb.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Separates registration of the phy and the lookup. The method
is copied from clkdev.c,
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add the driver driving the Marvell Berlin USB PHY. This allows to
initialize the PHY and to use it from the USB driver later.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Berlin BG2 also has a SATA PHY compatible with the current driver
except different PHY_BASE. Add a new compatible to the driver
reflecting the different PHY_BASE.
Acked-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Currently, Berlin SATA PHY driver assumes PHY_BASE address being
constant. While this PHY_BASE is correct for BG2Q, older BG2 PHY_BASE
is different. Prepare the driver for BG2 support by moving the phy_base
into private driver data.
Acked-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The driver for sun4i USB phys currently supports
only phy1 and phy2 which are used for USB host
controllers. This patch adds support for USB phy0,
which is used by the musb hdrc USB controller.
Signed-off-by: Roman Byshko <rbyshko@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Instead of using the node pointer of the PHY provider and then scanning its
child nodes to get a reference to the PHY, directly use the node pointer
present in of_phandle_args to get a reference to the PHY.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch to compensate tx impedance (Sata, PCIe)
depending on Soc cuts the kernel is built for.
Signed-off-by: Giuseppe Condorelli <giuseppe.condorelli@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
SSC is the technique of modulating the operating frequency of a signal
slightly to spread its radiated emissions over a range of frequencies.
This reduction in the maximum emission for a given frequency helps meet
radiated emission requirements.
These settings are applicable for PCIE with Internal clock.
Signed-off-by: Harsh Gupta <harsh.gupta@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch to tune on/off the ssc on miphy sata setup.
User can now enable ssc via dt blob, it is useful to reduce
effects of EMI.
Signed-off-by: Giuseppe Condorelli <giuseppe.condorelli@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The MiPHY28lp is a Generic PHY which can serve various SATA or PCIe
or USB3 devices.
Signed-off-by: alexandre torgue <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
commit e47d925 (usb: move the OTG state
from the USB PHY to the OTG structure) moved
the OTG state field from struct usb_phy to
struct usb_otg but, even though I fixed many
other build breakages, I still missed one
on phy-twl4030-usb.c.
Fix the build breakage now.
While at that, also a build warning introduced
by the same commit.
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The USB OTG port does not work since v3.16 on omap platform.
This is a regression introduced by the commit
eb82a3d846 (phy: omap-usb2: Balance pm_runtime_enable() on probe failure
and remove).
This because the call to pm_runtime_enable() function is moved after the
call to devm_phy_create() function, which has side effect since later in
the subsequent calls of devm_phy_create() there is a check with
pm_runtime_enabled() to configure few things.
Fixes: eb82a3d846
Signed-off-by: Oussama Ghorbel <ghorbel@pivasoftware.com>
Tested-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch prepares the introduction of the generic PHY support in the
USB OTG common functions. The USB PHY member of the OTG structure is
renamed to 'usb_phy' and modifications are done in all drivers accessing
it. Renaming this pointer will allow to keep the compatibility for USB
PHY drivers.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Before using the PHY framework instead of the USB PHY one, we need to
move the OTG state into another place, since it won't be available when
USB PHY isn't used. This patch moves the OTG state into the OTG
structure, and makes all the needed modifications in the drivers
using the OTG state.
[ balbi@ti.com : fix build regressions with phy-tahvo.c, musb_dsps.c,
phy-isp1301-omap, and chipidea's debug.c ]
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch removes the superflous .owner field for drivers which
use the module_platform_driver or platform_driver_register api,
as this is overriden in __platform_driver_register.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Currently the DP_PHY_ENABLE register is mapped in the driver,
and accessed to control power to the PHY.
With mfd-syscon and regmap interface available at our disposal,
it's wise to use that instead of using a 'reg' property for the
controller and allocating a memory resource for that.
To facilitate this, we have added another compatible string
for Exynso5420 SoC to acquire driver data which contains
different DP-PHY-CONTROL register offset.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This driver adds support for USB (1.1 and 2.0) phy for STiH415 and
STiH416 System-On-Chips from STMicroelectronics.
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This is the generic phy driver for the picoPHY ports used by the
USB2 and USB3 Host controllers when controlling usb2/1.1 devices. It
is found on STiH407 SoC family from STMicroelectronics.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
We're using threaded irq on a I2C bus and we're sleeping in
twl4030_usb_irq() as it calls twl4030_usb_linkstat() which
calls the i2c functions. If we ever need to lock for longer
I2C transaction sequences a mutex will allow us to do that
easily.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
There's no longer need for tracking the phy state in the driver
with asleep, we can now rely on runtime PM.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
We don't need twl4030_phy_power() any longer now that we have
the runtime PM calls. Let's get rid of it as it's confusing.
No functional changes, just move the code and use res instead
of ret as we are not returning that value.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
We can now let the interrupt and delayed work do all that's
needed with runtime PM.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Using the module_platform_driver macro to register the driver as this gets
rid of a lot of the boilerplate code.
Also remove .owner field as this gets overridden in __platform_driver_register.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Use the module_platform_driver macro to register the driver as this gets
rid of a lot of the boilerplate code.
Also remove .owner field as this gets overridden in __platform_driver_register.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The site specific OOM messages are unncessary, because they duplicate
messages from the memory subsystem which include dump_stack().
Removing these superflous messages makes the kernel smaller. A discussion
here http://patchwork.ozlabs.org/patch/324158/ found that all error paths
from kzalloc will print a error message, and that any error path which maybe
found which doesn't would be considered a bug in kzalloc.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The site specific OOM messages are unncessary, because they duplicate
messages from the memory subsystem which include dump_stack().
Removing these superflous messages makes the kernel smaller. A discussion
here http://patchwork.ozlabs.org/patch/324158/ found that all error paths
from kzalloc will print a error message, and that any error path which maybe
found which doesn't would be considered a bug in kzalloc.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The site specific OOM messages are unncessary, because they duplicate
messages from the memory subsystem which include dump_stack().
Removing these superflous messages makes the kernel smaller. A discussion
here http://patchwork.ozlabs.org/patch/324158/ found that all error paths
from kzalloc will print a error message, and that any error path which maybe
found which doesn't would be considered a bug in kzalloc.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The site specific OOM messages are unncessary, because they duplicate
messages from the memory subsystem which include dump_stack().
Removing these superflous messages makes the kernel smaller. A discussion
here http://patchwork.ozlabs.org/patch/324158/ found that all error paths
from kzalloc will print a error message, and that any error path which maybe
found which doesn't would be considered a bug in kzalloc.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Currently this driver is missing a check on the return value of devm_kzalloc,
which would cause a NULL pointer dereference in a OOM situation.
This patch adds the aformentioned missing check.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The site specific OOM messages are unncessary, because they duplicate
messages from the memory subsystem which include dump_stack().
Removing these superflous messages makes the kernel smaller. A discussion
here http://patchwork.ozlabs.org/patch/324158/ found that all error paths
from kzalloc will print a error message, and that any error path which maybe
found which doesn't would be considered a bug in kzalloc.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This PHY, though formally being a part of Renesas USBHS controller, contains the
UGCTRL2 register that controls multiplexing of the USB ports (Renesas calls them
channels) to the different USB controllers: channel 0 can be connected to either
PCI EHCI/OHCI or USBHS controllers, channel 2 can be connected to PCI EHCI/OHCI
or xHCI controllers.
This is a new driver for this USB PHY currently already supported under drivers/
usb/phy/. The reason for writing the new driver was the requirement that the
multiplexing of USB channels to the controller be dynamic, depending on what
USB drivers are loaded, rather than static as provided by the old driver. The
infrastructure provided by drivers/phy/phy-core.c seems to fit that purpose
ideally. The new driver only supports device tree probing for now.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
ST SPEAR1340-MIPHY support should be available only on
ST SPEAr1340 machine.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Pratyush Anand <pratyush.anand@st.com>
Cc: Mohit Kumar <mohit.kumar@st.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
ST SPEAR1310-MIPHY support should be available only on
ST SPEAr1310 machine.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Pratyush Anand <pratyush.anand@st.com>
Cc: Mohit Kumar <mohit.kumar@st.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
We index the RX/TX speed select values in the following way:
rx_tx_spd[miphy_phy->sata_gen];
However rx_tx_spd[] starts at index zero and the SATA_GENx's start
at one. In this patch we pad out the first element in rx_tx_spd[]
in an attempt to realign the values.
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Reported-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Enabling GENERIC_PHY in the shared (by most ARM sub-architectures)
defconfig multi_v7_defconfig is prohibited. Instead, we'll enable
it from the Kconfig whenever PHY_MIPHY365X is enabled.
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add a MODULE_DEVICE_TABLE call for OF match tables. This allows the
module to be autoloaded based on devicetree information.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Commit 249751f223 ("usb: phy: twl4030-usb: poll for ID disconnect")
added twl4030_id_workaround_work() to deal with lost interrupts
after ID pin goes down. Looks like commit f1ddc24c9e ("usb: phy:
twl4030-usb: remove *set_suspend* and *phy_init* ops") changed
things around for the generic phy framework, and delayed work no
longer got called except initially during boot.
The PHY connect and disconnect interrupts for twl4030-usb are not
working after disconnecting a USB-A cable from the board, and the
deeper idle states for omap are blocked as the USB controller
stays busy.
The issue can be solved by calling delayed work from twl4030_usb_irq()
when ID pin is down and the PHY is not asleep like we already do
in twl4030_id_workaround_work().
But as both twl4030_usb_irq() and twl4030_id_workaround_work()
already do pretty much the same thing, let's call twl4030_usb_irq()
from twl4030_id_workaround_work() instead of adding some more
duplicate code. We also must call sysfs_notify() only when we have
an interrupt and not from the delayed work as notified by
Grazvydas Ignotas <notasas@gmail.com>.
Fixes: f1ddc24c9e ("usb: phy: twl4030-usb: remove *set_suspend* and *phy_init* ops")
Cc: stable@vger.kernel.org # v3.13+
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Commit 30a70b026b ("usb: musb: fix obex in g_nokia.ko causing kernel
panic") attempted to fix runtime PM handling for PHYs that are on the
I2C bus. Commit 3063a12be2 ("usb: musb: fix PHY power on/off") then
changed things around to enable of PHYs that rely on runtime PM.
These changes however broke idling of the PHY and causes at least
100 mW extra power consumption on omaps, which is a lot with
the idle power consumption being below 10 mW range on many devices.
As calling phy_power_on/off from runtime PM calls in the USB
causes complicated issues with I2C connected PHYs, let's just let
the PHY do it's own runtime PM as needed. This leaves out the
dependency between PHYs and USB controller drivers for runtime
PM.
Let's fix the regression for twl4030-usb by adding minimal runtime
PM support. This allows idling the PHY on disconnect.
Note that we are changing to use standard runtime PM handling
for twl4030_phy_init() as that function just checks the state
and does not initialize the PHY. The PHY won't get initialized
until in twl4030_phy_power_on().
Fixes: 30a70b026b ("usb: musb: fix obex in g_nokia.ko causing kernel panic")
Fixes: 3063a12be2 ("usb: musb: fix PHY power on/off")
Cc: stable@vger.kernel.org # v3.15+
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
A handful of driver-related changes. We've had a bunch of them going in through
other branches as well, so it's only a part of what we really have this release.
Larger pieces are:
* Removal of a now unused PWM driver for atmel
- This includes AVR32 changes that have been appropriately acked.
* Performance counter support for the arm CCN interconnect
* OMAP mailbox driver cleanups and consolidation
* PCI and SATA PHY drivers for SPEAr 13xx platforms
* Redefinition (with backwards compatibility!) of PCI DT bindings for Tegra to
better model regulators/power.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=fsP6
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver changes from Olof Johansson:
"A handful of driver-related changes. We've had a bunch of them going
in through other branches as well, so it's only a part of what we
really have this release.
Larger pieces are:
- Removal of a now unused PWM driver for atmel
[ This includes AVR32 changes that have been appropriately acked ]
- Performance counter support for the arm CCN interconnect
- OMAP mailbox driver cleanups and consolidation
- PCI and SATA PHY drivers for SPEAr 13xx platforms
- Redefinition (with backwards compatibility!) of PCI DT bindings for
Tegra to better model regulators/power"
Note: this merge also fixes up the semantic conflict with the new
calling convention for devm_phy_create(), see commit f0ed817638 ("phy:
core: Let node ptr of PHY point to PHY and not of PHY provider") that
came in through Greg's USB tree.
Semantic merge patch by Stephen Rothwell <sfr@canb.auug.org.au> through
the next tree.
* tag 'drivers-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (38 commits)
bus: arm-ccn: Fix error handling at event allocation
mailbox/omap: add a parent structure for every IP instance
mailbox/omap: remove the private mailbox structure
mailbox/omap: consolidate OMAP mailbox driver
mailbox/omap: simplify the fifo assignment by using macros
mailbox/omap: remove omap_mbox_type_t from mailbox ops
mailbox/omap: remove OMAP1 mailbox driver
mailbox/omap: use devm_* interfaces
bus: ARM CCN: add PERF_EVENTS dependency
bus: ARM CCN PMU driver
PCI: spear: Remove spear13xx_pcie_remove()
PCI: spear: Fix Section mismatch compilation warning for probe()
ARM: tegra: Remove legacy PCIe power supply properties
PCI: tegra: Remove deprecated power supply properties
PCI: tegra: Implement accurate power supply scheme
ARM: SPEAr13xx: Update defconfigs
ARM: SPEAr13xx: Add pcie and miphy DT nodes
ARM: SPEAr13xx: Add bindings and dt node for misc block
ARM: SPEAr13xx: Fix static mapping table
phy: Add drivers for PCIe and SATA phy on SPEAr13xx
...
This is the bulk of new SoC enablement and other platform changes for 3.17:
* Samsung S5PV210 has been converted to DT and multiplatform
* Clock drivers and bindings for some of the lower-end i.MX 1/2 platforms
* Kirkwood, one of the popular Marvell platforms, is folded into the
mvebu platform code, removing mach-kirkwood.
* Hwmod data for TI AM43xx and DRA7 platforms.
* More additions of Renesas shmobile platform support
* Removal of plat-samsung contents that can be removed with S5PV210 being
multiplatform/DT-enabled and the other two old platforms being removed.
New platforms (most with only basic support right now):
* Hisilicon X5HD2 settop box chipset is introduced
* Mediatek MT6589 (mobile chipset) is introduced
* Broadcom BCM7xxx settop box chipset is introduced
+ as usual a lot other pieces all over the platform code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=5TJ6
-----END PGP SIGNATURE-----
Merge tag 'soc-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"This is the bulk of new SoC enablement and other platform changes for
3.17:
- Samsung S5PV210 has been converted to DT and multiplatform
- Clock drivers and bindings for some of the lower-end i.MX 1/2
platforms
- Kirkwood, one of the popular Marvell platforms, is folded into the
mvebu platform code, removing mach-kirkwood
- Hwmod data for TI AM43xx and DRA7 platforms
- More additions of Renesas shmobile platform support
- Removal of plat-samsung contents that can be removed with S5PV210
being multiplatform/DT-enabled and the other two old platforms
being removed
New platforms (most with only basic support right now):
- Hisilicon X5HD2 settop box chipset is introduced
- Mediatek MT6589 (mobile chipset) is introduced
- Broadcom BCM7xxx settop box chipset is introduced
+ as usual a lot other pieces all over the platform code"
* tag 'soc-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (240 commits)
ARM: hisi: remove smp from machine descriptor
power: reset: move hisilicon reboot code
ARM: dts: Add hix5hd2-dkb dts file.
ARM: debug: Rename Hi3716 to HIX5HD2
ARM: hisi: enable hix5hd2 SoC
ARM: hisi: add ARCH_HISI
MAINTAINERS: add entry for Broadcom ARM STB architecture
ARM: brcmstb: select GISB arbiter and interrupt drivers
ARM: brcmstb: add infrastructure for ARM-based Broadcom STB SoCs
ARM: configs: enable SMP in bcm_defconfig
ARM: add SMP support for Broadcom mobile SoCs
Documentation: arm: misc updates to Marvell EBU SoC status
Documentation: arm: add URLs to public datasheets for the Marvell Armada XP SoC
ARM: mvebu: fix build without platforms selected
ARM: mvebu: add cpuidle support for Armada 38x
ARM: mvebu: add cpuidle support for Armada 370
cpuidle: mvebu: add Armada 38x support
cpuidle: mvebu: add Armada 370 support
cpuidle: mvebu: rename the driver from armada-370-xp to mvebu-v7
ARM: mvebu: export the SCU address
...
This has the added advantages of being able to enable/disable each
of the channels as simply as enabling/disabling the DT node.
Suggested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The MiPHY365x is a Generic PHY which can serve various SATA or PCIe
devices. It has 2 ports which it can use for either; both SATA, both
PCIe or one of each in any configuration.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add a PHY driver for uses with AHCI based SATA controller driver on the
IPQ806x family of SoCs.
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch fixes a possible timeout in poll loop without actually
checking the register before return. In theory the there is a possibility
of loop being scheduled after a long lock/delay, which would then force
the loop to exit without actually checking the register.
Reported-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
In case of multi-phy PHY providers, each PHY should be modeled as a sub
node of the PHY provider. Then each PHY will have a different node pointer
(node pointer of sub node) than that of PHY provider. Added this provision
in the PHY core.
Also fixed all drivers to use the updated API.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Fixed of_phy_provider_lookup to return 'phy_provider' if _of_phy_get
passes the node pointer of the sub-node of phy provider node. This is
needed when phy provider implements multiple PHYs and each PHY is
modelled as the sub-node of PHY provider device node.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
The Berlin SoC has a two SATA ports. Add a PHY driver to handle them.
The mode selection can let us think this PHY can be configured to fit
other purposes. But there are reasons to think the SATA mode will be
the only one usable: the PHY registers are only accessible indirectly
through two registers in the SATA range, the PHY seems to be integrated
and no information tells us the contrary. For these reasons, make the
driver a SATA PHY driver.
Signed-off-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
mach-kirkwood has been removed, now that kirkwood lives in mach-mvebu.
Depend on MACH_KIRKWOOD, which will be set when these SoCs are built
as part of mach-mvebv.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add a PHY driver for uses with AHCI based SATA controller driver on the
APQ8064 family of SoCs.
This patch is a forward port from Qualcomm's v3.4 andriod kernel.
Tested on IFC6410 board.
CC: Sujit Reddy Thumma <sthumma@codeaurora.org>
Tested-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
USB DWC3 driver on Exynos platform does not work without its
corresponding phy driver. Hence make the PHY driver depend on
Exynos DWC3 driver and default it to yes to make things easier
for the end user.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Tested-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Since the USB 2.0 PHYs are required with EHCI/OHCI USB drivers and
USB gadget controller supported by the DWC2 gadget driver, make it
depend on them and default to ARCH_EXYNOS as they are meant for
Exynos platforms. Also, make the sub-drivers silent options enabling
them based on the SoC platforms that they are meant to work with. This
will make life easier for end users who do not have any way knowing the
dependencies.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Tested-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Some PHYs can be powered by an external power regulator.
e.g. USB_HS PHY on DRA7 SoC. Make the PHY core support a
power regulator.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch adds support for Exynos3250 SoC to Exynos2USB PHY driver.
Although Exynos3250 has only one device phy interface, the register
layout and all operations that are required to get it enabled are almost
same as on Exynos4x12. The only different is one more register
(REFCLKSEL) which need to be set and lack of MODE SWITCH register.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
8-bit delay value (0xF1) is required for GEN2 devices to be enumerated
consistently. Added an API to be called from PHY drivers to set this delay
value and called it from PIPE3 driver to set the delay value.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
PCIe PHY uses an external pll instead of the internal pll used by SATA
and USB3. So added support in pipe3 PHY to use external pll.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
The Exynos4412 USB 2.0 PHY hardware differs from the description provided
in the documentation. Some register bits have different function. This
patch fixes the defines of register bits and changes the way how phys are
powered on and off.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Tested-by: Daniel Drake <drake@endlessm.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Make local functions static, because these are used only in this
file.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
PTR_ERR_OR_ZERO simplifies the code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
PTR_ERR_OR_ZERO simplifies the code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
PTR_ERR_OR_ZERO simplifies the code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Jingoo Han <jg1.han@samsung.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add support for the Samsung's S5PV210 SoC to the Exynos USB 2.0 PHY driver.
Signed-off-by: Mateusz Krawczuk <m.krawczuk@partner.samsung.com>
[k.debski@samsung.com: cleanup and commit description]
[k.debski@samsung.com: make changes accordingly to the mailing list
comments]
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
ARM based ST Microelectronics's SPEAr1310/40 platforms uses ST's phy (known as
'miphy') for PCIe and SATA. This patch adds drivers for these miphys.
This also adds proper bindings for miphys.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Tested-by: Mohit Kumar <mohit.kumar@st.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
[viresh: fixed logs/cclist/checkpatch warnings, broken into smaller patches]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Here are some small USB fixes, PHY driver fixes (they ended up in this
tree for lack of somewhere else to put them), and some new USB device
ids.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlPBnZAACgkQMUfUDdst+ynTkACgwma2Ccj7DJl3g1zFEtM0h8ki
8RYAnirwiO0p1B7gIKlDIgGs25JIwN61
=tNZ2
-----END PGP SIGNATURE-----
Merge tag 'usb-3.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes, PHY driver fixes (they ended up in this
tree for lack of somewhere else to put them), and some new USB device
ids"
* tag 'usb-3.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
phy: omap-usb2: Balance pm_runtime_enable() on probe failure and remove
phy: core: Fix error path in phy_create()
drivers: phy: phy-samsung-usb2.c: Add missing MODULE_DEVICE_TABLE
phy: omap-usb2: fix devm_ioremap_resource error detection code
phy: sun4i: depend on RESET_CONTROLLER
USB: serial: ftdi_sio: Add Infineon Triboard
USB: ftdi_sio: Add extra PID.
usb: option: Add ID for Telewell TW-LTE 4G v2
USB: cp210x: add support for Corsair usb dongle
If probe fails then we need to call pm_runtime_disable() to balance
out the previous pm_runtime_enable() call. Else it will cause
unbalanced pm_runtime_enable() call in the succeding probe call.
This anomaly was observed when the call to devm_phy_create() failed
with -EPROBE_DEFER.
Balance out the pm_runtime_enable() call in .remove() as well.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prevent resources from being freed twice in case device_add() call
fails within phy_create(). Also use ida_simple_remove() instead of
ida_remove() as we had used ida_simple_get() to allocate the ida.
Cc: 3.13+ <stable@vger.kernel.org> # 3.13+
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allow phy-exynos-usb2 to be autoloaded based on devicetree information.
Tested on Odroid X2 with its USB subsystem build as modules.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
devm_ioremap_resource returns an ERR_PTR value, not NULL, on failure.
A simplified version of the semantic match that finds this problem is as
follows:
// <smpl>
@@
expression e,e1;
statement S;
@@
*e = devm_ioremap_resource(...);
if (!e1) S
// </smpl>
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver depend on the reset framework in a mandatory way. Make sure
reset_control_get is defined by adding this dependency in Kconfig
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When NO_IOMEM is enabled (e.g. score architecture), some drivers which
need HAS_IOMEM need notice about it, or it will report related warning:
warning: (GPIO_SCH && GPIO_ICH && GPIO_VX855 && GPIO_RDC321X && IE6XX_WDT && RADIO_WL1273 && HID_SENSOR_HUB && MFD_NVEC) selects MFD_CORE which has unmet direct dependencies (HAS_IOMEM)
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The USB phy controller in the A31 differs mostly from the older controllers
because it has a clock dedicated for each phy, while the older ones were having
a single clock for all the phys.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Move the phy initialization and variables declaration to the loop itself, since
it is where it really belongs. Also remove all the temporary variables, we can
use the structure members directly.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Adding support to enable/disable VBUS controlled by a
regulator, to enable vbus supply on the port.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add a new driver for the USB 3.0 PHY on Exynos5 series of SoCs.
The new driver uses the generic PHY framework and will interact
with DWC3 controller present on Exynos5 series of SoCs.
Also, created a new header file in linux/mfd/syscon/ for
Exynos5 SoCs and put the required PMU offset definitions
for the basic available PHYs.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
All other phy drivers use 'select', while this one is
the only one to use 'depends on'. This is not a bug, just
slightly inconsistent, so let's change it to do things the
same way as everyone else.
We may also want to turn GENERIC_PHY into a silent option
that only ever gets turned on if another driver needs it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Matt Porter <mporter@linaro.org>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The phys array is of size EXYNOS_MIPI_PHYS_NUM. Trying to access the
index EXYNOS_MIPI_PHYS_NUM should return an error.
Fixes: 069d2e26e9 "phy: Add driver for Exynos MIPI CSIS/DSIM DPHYs"
Signed-off-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
If the license string doesn't match exactly, the module refuses to load.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
As clocks might be named differently on multiple platforms, use a generic
name in the driver and allow device tree node to specify the platform
specific clock name.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The kernel oopses in phy_lookup() due to 'phy->init_data' being NULL if we
register PHYs from a device tree probing driver and then call phy_get() on a
device that has no representation in the device tree (e.g. a PCI device).
Checking the pointer before dereferening it and skipping an interation if
it's NULL prevents this kernel oops.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When OMAP_CONTROL_USB was renamed to OMAP_CONTROL_PHY (commit
14da699b), its dependencies were lost in the process. Nothing in the
commit message indicates that this removal was intentional, so I think
it was by accident and the dependencies should be restored.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Roger Quadros <rogerq@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The top-level phy-samsung-usb2 driver may be configured as a
loadable module, which currently causes link errors because
of the dependency on the exynos{5250,4x12,4210}_usb2_phy_config
symbol. Solving this could be achieved by exporting these
symbols, but as the SoC-specific parts of the driver are not
currently built as modules, it seems better to just link
everything into one module and avoid the need for the export.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These changes are mostly for ARM specific device drivers that either
don't have an upstream maintainer, or that had the maintainer ask
us to pick up the changes to avoid conflicts. A large chunk of this
are clock drivers (bcm281xx, exynos, versatile, shmobile), aside from
that, reset controllers for STi as well as a large rework of the
Marvell Orion/EBU watchdog driver are notable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=u/FI
-----END PGP SIGNATURE-----
Merge tag 'drivers-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver changes from Arnd Bergmann:
"These changes are mostly for ARM specific device drivers that either
don't have an upstream maintainer, or that had the maintainer ask us
to pick up the changes to avoid conflicts.
A large chunk of this are clock drivers (bcm281xx, exynos, versatile,
shmobile), aside from that, reset controllers for STi as well as a
large rework of the Marvell Orion/EBU watchdog driver are notable"
* tag 'drivers-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (99 commits)
Revert "dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac."
Revert "net: stmmac: Add SOCFPGA glue driver"
ARM: shmobile: r8a7791: Fix SCIFA3-5 clocks
ARM: STi: Add reset controller support to mach-sti Kconfig
drivers: reset: stih416: add softreset controller
drivers: reset: stih415: add softreset controller
drivers: reset: Reset controller driver for STiH416
drivers: reset: Reset controller driver for STiH415
drivers: reset: STi SoC system configuration reset controller support
dts: socfpga: Add sysmgr node so the gmac can use to reference
dts: socfpga: Add support for SD/MMC on the SOCFPGA platform
reset: Add optional resets and stubs
ARM: shmobile: r7s72100: fix bus clock calculation
Power: Reset: Generalize qnap-poweroff to work on Synology devices.
dts: socfpga: Update clock entry to support multiple parents
ARM: socfpga: Update socfpga_defconfig
dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac.
net: stmmac: Add SOCFPGA glue driver
watchdog: orion_wdt: Use %pa to print 'phys_addr_t'
drivers: cci: Export CCI PMU revision
...
- reset
- re-use qnap-poweroff driver for Synology NASs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=j/ZI
-----END PGP SIGNATURE-----
Merge tag 'mvebu-drivers-3.15-2' of git://git.infradead.org/linux-mvebu into next/drivers
Merge "mvebu drivers for v3.15" from Jason Cooper:
pull request #1:
- mvebu mbus
- use of_find_matching_node_and_match
- rtc
- use PTR_ERR_OR_ZERO in isl12057
- work around issue in mv where date returned is 2038
- kirkwood -> mach-mvebu
- various Kconfig oneliners to allow building kirkwood in -mvebu/
pull request #2:
- reset
- re-use qnap-poweroff driver for Synology NASs
* tag 'mvebu-drivers-3.15-2' of git://git.infradead.org/linux-mvebu:
Power: Reset: Generalize qnap-poweroff to work on Synology devices.
drivers: Enable building of Kirkwood drivers for mach-mvebu
rtc: mv: reset date if after year 2038
rtc: isl12057: use PTR_ERR_OR_ZERO to fix coccinelle warnings
bus: mvebu-mbus: make use of of_find_matching_node_and_match
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch adds support for the APM X-Gene SoC 15Gbps Multi-purpose PHY.
This is the physical layer interface for the corresponding host
controller. Currently, only external clock and Gen3 SATA mode
are supported.
Signed-off-by: Loc Ho <lho@apm.com>
Signed-off-by: Tuan Phan <tphan@apm.com>
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The OMAP_USB2 and OMAP_PIPE3 PHY devices will not be
detected if the OMAP_OCP2SCP bus driver is not present.
Make them depend on it.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Due to Errata i783, SATA breaks if its DPLL is idled. The recommeded
workaround to issue a softreset to the SATA controller doesn't seem to
work. Here we just prevent SATA DPLL from Idling and hence avoid
the issue altogether.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Limit .power_on() and .power_off() to just control the
PHY power and not the DPLL. The DPLL will be enabled
in .init() and idled in .exit().
Don't reprogram the DPLL if it has been already locked
by the bootloader. This fixes a problem with SATA, where
it fails if SATA was used by the bootloader.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
SATA PHY doesn't need 'wkupclk; and 'refclk' so don't
try to get them for SATA PHY.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
USB and SATA DPLLs need different settings. Provide
the SATA DPLL settings and use the proper DPLL settings
based on device tree node's compatible_id.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
As this driver is no longer USB specific, use generic clock names.
- Fix PLL_SD_SHIFT from 9 to 10
- Don't separate prepare/unprepare clock from enable/disable. This
ensures optimal power savings.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The dra7-usb2 and am437-usb2 bindings have not yet been used.
Change them to be more elegant.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Rename struct omap_control_usb to struct omap_control_phy since it can
be used to control PHY of USB, SATA and PCIE. Also move the driver and
include files under *phy* and made the corresponding changes in the users
of phy-omap-control.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Add a new compatible for OMAP5 since it does not use any of the
OTG operations as of now.
HAS_SRP and SET_VBUS functionalities are used only for OMAP4.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Enable the dra7x errata workaround for false disconnect problem
with USB2PHY. False disconnects were detected with some of the devices.
Reduce the sensitivity of the disconnect logic within the USB2PHY subsystem
to enusre these false disconnects are not registered.
[george.cherian@ti.com]
While at that, pass proper flags for each SoC's. This is a common driver
used across OMAP4,OMAP5,DRA7xx and AM437x USB2PHY.
False disconnect workaround is currently applicable for only DRA7x.
Signed-off-by: Austin Beam <austinbeam@ti.com>
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Adapt phy-omap-usb2 driver for AM437x.
- Add new comaptible "ti,am437x-usb2" for AM437x
- Pass proper data to differentiate AM437x and others.
- AM437x doesnot support set_vbus and start_srp.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add support for Exynos 5250. This driver is to replace the old
USB 2.0 PHY driver.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add a new driver for the Exynos USB 2.0 PHY. The new driver uses the generic
PHY framework. The driver includes support for the Exynos 4x10 and 4x12
SoC families.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Adding devm_of_phy_get will allow to get phys by supplying a
pointer to the struct device_node instead of struct device.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Previously the of_phy_get function took a struct device * and
was declared static. It was impossible to call it from
another driver and thus it was impossible to get phy defined
for a given node. The old function was renamed to _of_phy_get
and was left for internal use. of_phy_get function was added
and it was exported. The function enables to get a phy for
a given device tree node.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
No functional change. Moved omap_usb.h from linux/usb/ to linux/phy/.
Also removed the unused members of struct omap_usb (after phy-omap-pipe3
started using it's own header file)
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Now that omap-usb2 is adapted to the new generic PHY framework,
*set_suspend* ops can be removed from omap-usb2 driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Adapted omap-usb3 PHY driver to Generic PHY Framework and moved phy-omap-usb3
driver in drivers/usb/phy to drivers/phy and also renamed the file to
phy-ti-pipe3 since this same driver will be used for SATA PHY and
PCIE PHY.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
DT-enabled Dove will move over from ARCH_DOVE in mach-dove to MACH_DOVE in
mach-mvebu. As non-DT ARCH_DOVE will stay to rot for a while, add a new
DT-only MACH_DOVE Kconfig.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
The Allwinner A1x / A2x SoCs have 2 or 3 usb phys which are all accessed
through a single set of registers. Besides this there are also some other
phy related bits which need poking, which are per phy, but shared between the
ohci and ehci controllers, so these are also controlled from this new phy
driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch adds the SATA PHY driver for Exynos5250.This driver uses the
generic PHY framework to deal with SATA PHY.Exynos5250 SATA PHY comprises
of CMU and TRSV blocks which are of I2C register Map.So this driver
configures the CMU and TRSV block of exynos5250 SATA PHY using i2c.
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Signed-off-by: Girish K S <ks.giri@samsung.com>
Signed-off-by: Vasanth Ananthan <vasanth.a@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Instead of requiring user to figure out when PHY_EXYNOS_DP_VIDEO needs
to be selected select it by default for Exynos SoCs. Also enable it
when COMPILE_TEST is selected. If required the display port PHY driver
can be then disabled or compiled in as module.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Instead of requiring user to figure out when PHY_EXYNOS_MIPI_VIDEO needs
to be selected select it by default for Exynos SoCs. Also enable it when
COMPILE_TEST is selected. If required the MIPI CSIS/DPHY driver can be
then disabled or compiled in as module.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
PTR_ERR_OR_ZERO simplifies the code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Matt Porter <mporter@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Semicolon after switch statement is not needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Silences the following warnings:
WARNING: sizeof *twl should be sizeof(*twl)
WARNING: sizeof *otg should be sizeof(*otg)
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
With the move of kirkwood into mach-mvebu, drivers Kconfig need
tweeking to allow the kirkwood specific drivers to be built.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Bryan Wu <cooloney@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Registering phy_provider before creating the PHY can result in PHY
callbacks being invoked which will lead to aborts. In order to avoid this
invoke phy_provider_register after phy_create and phy_set_drvdata.
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
include/phy/phy.h has stub code in there for when building without the
phy-core enabled. This is useful for generic drivers such as ahci-platform,
ehci-platoform and ohci-platform which have support for driving an optional
phy passed to them through the devicetree.
Since on some boards this phy functionality is not needed, being able to
disable the phy subsystem without needing a lot of #ifdef magic in the
driver using it is quite useful.
However this breaks when the module using the phy subsystem is build-in and
the phy-core is not, which leads to the build failing with missing symbol
errors in the linking stage of the zImage.
Which leads to gems such as this being added to the Kconfig for achi_platform:
depends on GENERIC_PHY || !GENERIC_PHY
Rather then duplicating this code in a lot of places using the phy-core,
I believe it is better to simply not allow the phy-core to be built as a
module. The phy core is quite small and has no external dependencies, so
always building it in when enabling it should not be an issue.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The phy-core allows phy_init and phy_power_on to be called multiple times,
but before this patch -ENOSUPP from phy_pm_runtime_get_sync would be
propagated to the caller for the 2nd and later calls.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In various cases errors may be expected, ie probe-deferral or a call to
phy_get from a driver where the use of a phy is optional.
Rather then adding all sort of complicated checks for this, and/or adding
special functions like devm_phy_get_optional, simply don't log an error,
and let deciding if get_phy returning an error really should result in a
dev_err up to the caller.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On archs like S390 or um this driver cannot build nor work.
Make it depend on HAS_IOMEM to bypass build failures.
drivers/phy/phy-bcm-kona-usb2.c:114: undefined reference to `devm_ioremap_resource'
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add devm_phy_optional_get and phy_optional_get, which should be used
when the phy is optional. They does not return an error when the phy
does not exist, rather they returns NULL, which is considered as a valid
phy, but results in NOPs when used with the consumer API.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The common clock framework considers NULL a valid clock
reference. This makes handling optional clocks simple, in that if the
optional clock is not available, a NULL reference can be used in the
place of a real clock, simplifying the clock consumer.
Extend this concept to the phy consumer API. A NULL can be passed to
the release calls, the phy_init() and phy_exit() calls, and
phy_power_on() and phy_power_off() and a NOP is performed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Pull networking updates from David Miller:
1) BPF debugger and asm tool by Daniel Borkmann.
2) Speed up create/bind in AF_PACKET, also from Daniel Borkmann.
3) Correct reciprocal_divide and update users, from Hannes Frederic
Sowa and Daniel Borkmann.
4) Currently we only have a "set" operation for the hw timestamp socket
ioctl, add a "get" operation to match. From Ben Hutchings.
5) Add better trace events for debugging driver datapath problems, also
from Ben Hutchings.
6) Implement auto corking in TCP, from Eric Dumazet. Basically, if we
have a small send and a previous packet is already in the qdisc or
device queue, defer until TX completion or we get more data.
7) Allow userspace to manage ipv6 temporary addresses, from Jiri Pirko.
8) Add a qdisc bypass option for AF_PACKET sockets, from Daniel
Borkmann.
9) Share IP header compression code between Bluetooth and IEEE802154
layers, from Jukka Rissanen.
10) Fix ipv6 router reachability probing, from Jiri Benc.
11) Allow packets to be captured on macvtap devices, from Vlad Yasevich.
12) Support tunneling in GRO layer, from Jerry Chu.
13) Allow bonding to be configured fully using netlink, from Scott
Feldman.
14) Allow AF_PACKET users to obtain the VLAN TPID, just like they can
already get the TCI. From Atzm Watanabe.
15) New "Heavy Hitter" qdisc, from Terry Lam.
16) Significantly improve the IPSEC support in pktgen, from Fan Du.
17) Allow ipv4 tunnels to cache routes, just like sockets. From Tom
Herbert.
18) Add Proportional Integral Enhanced packet scheduler, from Vijay
Subramanian.
19) Allow openvswitch to mmap'd netlink, from Thomas Graf.
20) Key TCP metrics blobs also by source address, not just destination
address. From Christoph Paasch.
21) Support 10G in generic phylib. From Andy Fleming.
22) Try to short-circuit GRO flow compares using device provided RX
hash, if provided. From Tom Herbert.
The wireless and netfilter folks have been busy little bees too.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2064 commits)
net/cxgb4: Fix referencing freed adapter
ipv6: reallocate addrconf router for ipv6 address when lo device up
fib_frontend: fix possible NULL pointer dereference
rtnetlink: remove IFLA_BOND_SLAVE definition
rtnetlink: remove check for fill_slave_info in rtnl_have_link_slave_info
qlcnic: update version to 5.3.55
qlcnic: Enhance logic to calculate msix vectors.
qlcnic: Refactor interrupt coalescing code for all adapters.
qlcnic: Update poll controller code path
qlcnic: Interrupt code cleanup
qlcnic: Enhance Tx timeout debugging.
qlcnic: Use bool for rx_mac_learn.
bonding: fix u64 division
rtnetlink: add missing IFLA_BOND_AD_INFO_UNSPEC
sfc: Use the correct maximum TX DMA ring size for SFC9100
Add Shradha Shah as the sfc driver maintainer.
net/vxlan: Share RX skb de-marking and checksum checks with ovs
tulip: cleanup by using ARRAY_SIZE()
ip_tunnel: clear IPCB in ip_tunnel_xmit() in case dst_link_failure() is called
net/cxgb4: Don't retrieve stats during recovery
...
Here's the big USB pull request for 3.14-rc1
Lots of little things all over the place, and the usual USB gadget
updates, and XHCI fixes (some for an issue reported by a lot of people.)
USB PHY updates as well as chipidea updates and fixes.
All of these have been in the linux-next tree with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlLdjwIACgkQMUfUDdst+ylBIQCgkRoR8lJc0L5lZ3fugIJL4IzZ
j6AAn0nBLP6VI0cvUEi3TcrPTzv4MEuL
=Yb+I
-----END PGP SIGNATURE-----
Merge tag 'usb-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here's the big USB pull request for 3.14-rc1
Lots of little things all over the place, and the usual USB gadget
updates, and XHCI fixes (some for an issue reported by a lot of
people). USB PHY updates as well as chipidea updates and fixes.
All of these have been in the linux-next tree with no reported issues"
* tag 'usb-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (318 commits)
usb: chipidea: udc: using MultO at TD as real mult value for ISO-TX
usb: chipidea: need to mask INT_STATUS when write otgsc
usb: chipidea: put hw_phymode_configure before ci_usb_phy_init
usb: chipidea: Fix Internal error: : 808 [#1] ARM related to STS flag
usb: chipidea: imx: set CI_HDRC_IMX28_WRITE_FIX for imx28
usb: chipidea: add freescale imx28 special write register method
usb: ehci: add freescale imx28 special write register method
usb: core: check for valid id_table when using the RefId feature
usb: cdc-wdm: resp_count can be 0 even if WDM_READ is set
usb: core: bail out if user gives an unknown RefId when using new_id
usb: core: allow a reference device for new_id
usb: core: add sanity checks when using bInterfaceClass with new_id
USB: image: correct spelling mistake in comment
USB: c67x00: correct spelling mistakes in comments
usb: delete non-required instances of include <linux/init.h>
usb:hub set hub->change_bits when over-current happens
Revert "usb: chipidea: imx: set CI_HDRC_IMX28_WRITE_FIX for imx28"
xhci: Set scatter-gather limit to avoid failed block writes.
xhci: Avoid infinite loop when sg urb requires too many trbs
usb: gadget: remove unused variable in gr_queue_int()
...
On archs like S390 or um this driver cannot build nor work.
Make it depend on HAS_IOMEM to bypass build failures.
drivers/built-in.o: In function `exynos_mipi_video_phy_probe':
drivers/phy/phy-exynos-mipi-video.c:130: undefined reference to `devm_ioremap_resource'
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kirkwood and Dove can turn the SATA phy on and off. Add a PHY driver
to control this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
There were a few places where variables are initialized unncessarily.
Remove those initializations.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Increment 'init_count' only if the 'init' callback succeeded and decrement
'init_count' only if the 'exit' callback succeded. Increment 'power_count'
only if 'power_on' callback succeded and if it failed disable the clocks using
phy_pm_runtime_put_sync(). Also decrement 'power_count' only if 'power_off'
callback succeded and if it failed do not disable the clocks.
Reported-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
In case pm_runtime_get*() fails, it still
increments pm usage counter, so we *must*
make sure to pm_runtime_put() even in those
cases.
This patch fixes that mistake the same way
usbcore treats those possible failures.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add a driver for the internal Broadcom Kona USB 2.0 PHY found
on the BCM281xx family of SoCs.
Signed-off-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fixes
warning: (OMAP_USB2 && TWL4030_USB) selects USB_PHY which has unmet
direct dependencies (USB_SUPPORT)
that shows up while disabling USB_SUPPORT from menuconfig.
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If this was called with a NULL "dev" then it lead to a NULL dereference
when we called dev_WARN(). I have changed it to WARN_ON() so that we
get a stack dump and can fix the caller.
The rest of this patch is just cleanup like returning directly instead
of having do-nothing gotos. Using descriptive labels instead of
GW-BASIC style "err0" and "err1". I also flipped the order of
put_device() and ida_remove() so they are a mirror reflection of the
order they were allocated.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'phy' was not being freed upon error in one of the cases.
Adjust the 'goto's to fix this.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Final conversions to configfs for mass storage, acm_ms, and
multi gadgets.
MUSB should now work out of the box on AM335x-based boards
(beagle bone white and black) with DMA thanks to Sebastian's
work.
We can now enable VERBOSE_DEBUG on builds of drivers/usb/gadget/
by selecting CONFIG_USB_GADGET_VERBOSE.
s3c-hsotg got quite a few non-critical fixes but also learned
a few new tricks (isochronous transfers, multi count support).
The Marvel USB3 Controller driver got a memory leak fix.
devm_usb_get_phy() learned not to return NULL, ever.
Other than these patches, we have the usual set of cleanups
ranging from removal of unnecessary *_set_drvdata() to using
SIMPLE_DEV_PM_OPS.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=LDY7
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.13
Final conversions to configfs for mass storage, acm_ms, and
multi gadgets.
MUSB should now work out of the box on AM335x-based boards
(beagle bone white and black) with DMA thanks to Sebastian's
work.
We can now enable VERBOSE_DEBUG on builds of drivers/usb/gadget/
by selecting CONFIG_USB_GADGET_VERBOSE.
s3c-hsotg got quite a few non-critical fixes but also learned
a few new tricks (isochronous transfers, multi count support).
The Marvel USB3 Controller driver got a memory leak fix.
devm_usb_get_phy() learned not to return NULL, ever.
Other than these patches, we have the usual set of cleanups
ranging from removal of unnecessary *_set_drvdata() to using
SIMPLE_DEV_PM_OPS.
Signed-of-by: Felipe Balbi <balbi@ti.com>
Fix argument passed to the register setup helper function so
the phy is actually disabled. Now due to cut&paste error 1 is
passed to both phy_power_on() and phy_power_off().
Reported by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a PHY provider driver for the Samsung Exynos SoC Display Port PHY.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
omap_get_control_dev() is being deprecated as it doesn't support
multiple instances. As control device is present only from OMAP4
onwards which supports DT only, we use phandles to get the
reference to the control device.
As we don't support non-DT boot, we just bail out on probe
if device node is not present.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that twl4030-usb is adapted to the new generic PHY framework,
*set_suspend* and *phy_init* ops can be removed from twl4030-usb driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yoshihiro Shimoda