We have forced usb3 to work in usb2 only mode in firmware by setting
usb3tousb2_en (bit3 of GRF_USB3PHY0/1_CON0) to 1, and setting
host_u3_port_disable (bit0 of GRF_USB3OTG0/1_CON1) to 1 and host_u3_port
(bit15~12 of GRF_USB3OTG0/1_CON1) to 0. So we need to re-enable usb3
host.
Note that the RK3399 TRM suggests that we should keep the whole usb3
controller in reset for the duration of the Type-C PHY initialization.
However, it's hard to assert the reset in the current framework of
reset. And according to the TRM, it doesn't require that we should
clear the usb3tousb2 bit before pipe ready. So let's enable the usb3
host after pipe ready to avoid the Type-C PHY initialization failure.
Signed-off-by: William wu <wulf@rock-chips.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Adding properties for various register fields in the DT doesn't scale and
this information should be in the driver instead.
Before this patch these registers (description below) were specified in
the DT, every register node contained 3 sections: offset, enable bit,
write mask bit.
- rockchip,typec-conn-dir : the register of type-c connector direction,
for type-c phy0, it must be <0xe580 0 16>;
for type-c phy1, it must be <0xe58c 0 16>;
- rockchip,usb3tousb2-en : the register of type-c force usb3 to usb2
enable control.
for type-c phy0, it must be <0xe580 3 19>;
for type-c phy1, it must be <0xe58c 3 19>;
- rockchip,external-psm : the register of type-c phy external psm clock
selection.
for type-c phy0, it must be <0xe588 14 30>;
for type-c phy1, it must be <0xe594 14 30>;
- rockchip,pipe-status : the register of type-c phy pipe status.
for type-c phy0, it must be <0xe5c0 0 0>;
for type-c phy1, it must be <0xe5c0 16 16>;
After this patch these register definitions are in the driver. So can be
removed from the DT. Note that there are 2 type-c phys for RK3399 with
different offsets, the driver checks the phy base address of the running
instance and applies the right offsets.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Let's add support for the GPIO controlled USB PHY on the MDM6600 modem.
It is used on some Motorola Mapphone series of phones and tablets such
as Droid 4.
The MDM6600 is hardwired to the first OHCI port in the Droid 4 case, and
is controlled by several GPIOs. The USB PHY is integrated into the MDM6600
device it seems. We know this as we get L3 errors from omap-usb-host if
trying to use the PHY before MDM6600 is configured.
The GPIOs controlling MDM6600 are used to power device on and off, to
configure the USB start-up mode (normal mode versus USB flashing), and
they also tell the state of the MDM6600 device.
The two start-up mode GPIOs are dual-purposed and used for out of band
(OOB) wake-up for USB and TS 27.010 serial mux. But we need to configure
the USB start-up mode first to get MDM6600 booted in the right mode to
be usable in the first place.
Note that the Motorola Mapphone Linux kernel tree has a "radio-ctrl"
driver for modems. But it really does not control the radio at all, it
just controls the modem power and start-up mode for USB. So I came to
the conclusion that we're better off having this done in the USB PHY
driver. For adding support for USB flashing mode, we can later on add
a kernel module option for flash_mode=1 or something similar.
Also note that currently there is no PM runtime support for the OHCI
on omap variant SoCs. So for low(er) power idle states, currenty both
ohci-platform and phy-mapphone-mdm6600 must be unloaded or unbound.
For reference here is what I measured for total power consumption on
an idle Droid 4 with and without USB related MDM6600 modules:
idle lcd off phy-mapphone-mdm6600 ohci-platform
153mW 284mW 344mW
So it seems that MDM6600 is currently not yet idling even with it's
radio turned off, but that's something that is beyond the control of
this USB PHY driver. This patch does get us to the point where modem
data and GPS are usable with libqmi and ModemManager for example.
Voice calls need more audio driver work.
Cc: devicetree@vger.kernel.org
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
It adds inno-usb2-phy driver for hi3798cv200 SoC USB 2.0 support. One
inno-usb2-phy device can support up to two PHY ports. While there is
device level reference clock and power reset to be controlled, each PHY
port has its own utmi reset that needs to assert/de-assert as needed.
Hi3798cv200 needs to access PHY port0 register via particular peripheral
syscon controller register to control PHY, like turning on PHY clock.
Signed-off-by: Pengcheng Li <lpc.li@hisilicon.com>
Signed-off-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch adds support for r8a77965 (R-Car M3-N). This SoC has
dedicated pins.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch adds phy transceiver driver for STM32 USB PHY Controller
(USBPHYC) that provides dual port High-Speed phy for OTG (single port)
and EHCI/OHCI host controller (two ports).
One port of the phy is shared between the two USB controllers through
a UTMI+ switch.
[fengguang.wu@intel.com: Make stm32_usbphyc_get_pll_params() to be static]
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
These configs select MFD_SYSCON, but do not depend on HAS_IOMEM.
Compile testing on architecture without HAS_IOMEM causes "unmet
direct dependencies" in Kconfig phase.
Detected by "make ARCH=score allyesconfig".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This adds a new driver for the USB3 PHY found on Meson GXL and GXM SoCs
(both SoCs are using the same USB PHY register layout).
Unfortunately there is no documentation for this PHY in the public S905X
datasheet (published for example by Khadas). What we know so far about
this PHY:
- even though the Meson GXL and GXM SoCs do not expose an USB3 port (the
dwc3 controller only has USB2 ports enabled) we need to initialize the
USB3 PHY (specifically USB_R1_U3H_FLADJ_30MHZ_REG_MASK). Without this
initialization high-speed USB devices (especially USB hard disks and
thumb drives, slower devices like mice do not seem to be affected)
- on some boards the USB3 PHY starts in "device mode" - we want to bring
it into a known state (by switching it to host mode for now).
- it is responsible for the OTG detection and for switching the first
USB2 PHY between host and peripheral (aka device) mode. an interrupt
can be used to detect changes between host and device mode.
There are five inputs to this register area:
- the clock and reset line for the USB3 PHY itself
- the clock and reset line for the peripheral mode and OTG detection
logic (on the GXL and GXM SoCs these are the same clock and reset line
as for the USB3 PHY itself, but Amlogic sees this as two different
components - even though they share the same register space - so they
have to be passed individually to allow specifying different inputs on
other SoCs if needed)
- the interrupt for the OTG detection logic
The whole OTG detection logic is not implemented yet.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Yixun Lan <yixun.lan@amlogic.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Make the value written into the USB_PHY_RX_CTRL configuration register
match 0xAA79 value written by manufacturer-supplied kernels for Sony
NSZ-GS7 (Berlin2 SoC), Google Chromecast and Valve Steam Link (BG2CD).
This fixes timeouts communicating to the internal hub on Steam Link.
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Alexander Monakov <amonakov@ispras.ru>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
There are two parameters, ref_clk and coefficient, for U2 slew rate
calibrate which may vary on different SoCs, here allow them to be
configurable
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The default value of mcu_bus_ck_gate_en is 1, if clear it, will
prevent system to enter deep idle mode, so keep its default value
and without affecting PCIe function.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
If regmap_update_bits() fails in lpc18xx_usb_otg_phy_power_on(),
lpc->clk is left enabled.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The AXP223 PMIC, like the AXP221, does not generate VBUS change
interrupts when N_VBUSEN is used to drive VBUS for the OTG port
on the board.
This was not noticed until recently, as most A23/A33 boards use
a GPIO pin that does not support interrupts for OTG ID detection.
This forces the driver to use polling. However the A33-OlinuXino
uses a pin that does support interrupts, so the driver uses them.
However the VBUS interrupt never fires, and the driver never gets
to update the VBUS status. This results in musb timing out waiting
for VBUS to rise.
This was worked around for the AXP221 by resorting to polling
changes in commit 91d96f06a7 ("phy-sun4i-usb: Add workaround for
missing Vbus det interrupts on A31"). This patch adds the A23 and
A33 to the list of SoCs that need the workaround.
Fixes: fc1f45ed30 ("phy-sun4i-usb: Add support for the usb-phys on the
sun8i-a33 SoC")
Fixes: 123dfdbcfa ("phy-sun4i-usb: Add support for the usb-phys on the
sun8i-a23 SoC")
Cc: <stable@vger.kernel.org> # 4.3.x: 68dbc2ce77 phy-sun4i-usb:
Use of_match_node to get model specific config data
Cc: <stable@vger.kernel.org> # 4.3.x: 5cf700ac9d phy: phy-sun4i-usb:
Fix optional gpios failing probe
Cc: <stable@vger.kernel.org> # 4.3.x: 04e59a0211 phy-sun4i-usb:
Fix irq free conditions to match request conditions
Cc: <stable@vger.kernel.org> # 4.3.x: 91d96f06a7 phy-sun4i-usb:
Add workaround for missing Vbus det interrupts on A31
Cc: <stable@vger.kernel.org> # 4.3.x
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
While the specific UFS PHY drivers (14nm and 20nm) have a module
license, the common base module does not, leading to a Kbuild
failure:
WARNING: modpost: missing MODULE_LICENSE() in drivers/phy/qualcomm/phy-qcom-ufs.o
FATAL: modpost: GPL-incompatible module phy-qcom-ufs.ko uses GPL-only symbol 'clk_enable'
This adds a module description and license tag to fix the build.
I added both Yaniv and Vivek as authors here, as Yaniv sent the initial
submission, while Vivek did most of the work since.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The U2P_R2 register provides "test mode" functionality for bits 17:0.
These are only used during SoC development and should be left untouched
on production SoC versions.
Rename these register definitions to indicate that these are for "test
mode" only.
While here, also merge the definitions for U2P_R2_DATA_IN_MASK and
U2P_R2_DATA_IN_EN_MASK (bits 0:7) because Amlogic's internal
documentation suggests that these bits belong together. The old
definition was not taken from the documentation but rather from a struct
definition in the Amlogic GPL kernel sources.
No functional changes.
Suggested-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The USB2 PHY can switch between PHY_MODE_USB_HOST and
PHY_MODE_USB_DEVICE. However, it cannot do it on it's own since it
requires re-routing of the corresponding USB pins from dwc3 (which is
used for host-mode) to dwc2 (which is used for device-mode).
Thus we don't need to auto-detect the mode based on the USB controller,
which simplifies the driver code.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The Meson GXL USB2 PHYs require an additional clock (USB) which has to
be enabled. If that clock is disabled then all PHY registers read 0x0.
Luckily for us that clock is always enabled (either by harddware
defaults, the bootrom, or any of the bootloaders before u-boot/BL3-3).
The OTG capable USB2 PHY additionally has a reset line (USB_OTG, which
is shared with other components, such as the USB3 PHY for example).
Extend the driver so it handles this clock and the shared reset line.
We only trigger the reset during the .init phase since it's a shared
reset line, so triggering it during the driver's .reset implementation
would effectively also only trigger it once anyways.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
devm_phy_create can return -EPROBE_DEFER if the phy-supply is not ready
yet. Silence this warning as the driver framework will re-attempt
registering the PHY - this second try works without any errors. So only
log actual errors to keep the kernel log free of misleading error
messages.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Just use the API instead of open-coding it, no functional change
intended.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
It turns out that 5us isn't enough for all cases, so let's
retry some more times to wait for caldone.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Exynos4212 support was removed by commit bca9085e0a ("ARM: dts:
exynos: remove Exynos4212 support (dead code)").
Remove the SOC_EXYNOS4212 dependency from PHY_EXYNOS4X12_USB.
Discovered with the
https://github.com/ulfalizer/Kconfiglib/blob/master/examples/list_undefined.py
script.
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The SPDX identifier is a legally binding shorthand, which
can be used instead of the full boiler plate text.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Disable clocks and enable PHY autonomous mode to detect
wakeup events when PHY is suspended.
Core driver should notify speed to PHY driver to enable
LFPS and/or RX_DET interrupts.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Disable clocks and enable DP/DM wakeup interrupts when
suspending PHY.
Core driver should notify speed to PHY driver to enable
appropriate DP/DM wakeup interrupts polarity in suspend state.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add following USB speed related PHY modes:
LS (Low Speed), FS (Full Speed), HS (High Speed), SS (Super Speed)
Speed related information is required by some QCOM PHY drivers
to program PHY monitor resume/remote-wakeup events in suspended
state. Speed is needed in order to set correct polarity of wakeup
events for detection. E.g. QUSB2 PHY monitors DP/DM line state
depending on whether speed is LS or FS/HS to detect resume.
Similarly QMP USB3 PHY in SS mode should monitor RX terminations
attach/detach and LFPS events depending on SSPHY is active or not.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
QMP V3 USB3 PHY is a DisplayPort (DP) and USB combo PHY
with dual RX/TX lanes to support type-c. There is a
separate block DP_COM for configuration related to type-c
or DP. Add support for dp_com region and secondary rx/tx
lanes initialization.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Registers offsets for QMP V3 PHY are changed from
previous versions (1/2), update same in header file.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
New revision (v3) of QMP PHY uses different offsets
for almost all of the registers. Hence, move these
definitions to header file so that updated offsets
can be added for QMP v3.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Use register layout to add additional registers present
on QUSB2 PHY V2 version for PHY initialization.
Other than new registers on V2, following two register's
offset and bit definitions are different: POWERDOWN control
and PLL_STATUS.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
New version of QUSB2 PHY has some registers offset changed.
Add support to have register layout for a target and update
the same in phy_configuration.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Driver is currently performing PHY reset after starting
SERDES/PCS. As per hardware datasheet reset must be done
before starting PHY. Hence, update the sequence.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
PHY block or asynchronous reset requires signal
to be asserted before de-asserting. Driver is only
de-asserting signal which is already low, hence
reset operation is a no-op. Fix this by asserting
signal first. Also, resetting requires PHY clocks
to be turned ON only after reset is finished. Fix
that as well.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
PHY must be powered on before turning ON clocks and
attempting to initialize it. Driver is exposing
separate init and power_on routines for this.
Apparently USB dwc3 core driver performs power-on
after init. Also, poweron and init for QUSB2 PHY
need to be executed together always, hence remove
poweron callback from phy_ops and explicitly perform
this from init, similar changes needed for poweroff.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
PHY regulators which are enabled from power_on() must be ON
before turning-on clocks and initializing it as part of init().
As most of the core drivers perform power_on() after init(), move
PHY regulators enable to com_init() and use power_on() to
only enable pipe_clk. This pipe_clk is output from PHY and some
core drivers e.g. PCIe follow specific sequence after phy_init()
that mandates pipe_clk to be enabled from power_on() only.
On similar lines move clk_enable from init() to com_init() which
executes once for multi lane PHYs.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Move from using array of clocks to clk_bulk_* APIs that
are available now.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Pipe clock comes out of the phy and is available as long as
the phy is turned on. Clock controller fails to gate this
clock after the phy is turned off and generates a warning.
/ # [ 33.048561] gcc_usb3_phy_pipe_clk status stuck at 'on'
[ 33.048585] ------------[ cut here ]------------
[ 33.052621] WARNING: CPU: 1 PID: 18 at ../drivers/clk/qcom/clk-branch.c:97 clk_branch_wait+0xf0/0x108
[ 33.057384] Modules linked in:
[ 33.066497] CPU: 1 PID: 18 Comm: kworker/1:0 Tainted: G W 4.12.0-rc7-00024-gfe926e34c36d-dirty #96
[ 33.069451] Hardware name: Qualcomm Technologies, Inc. DB820c (DT)
...
[ 33.278565] [<ffff00000849b27c>] clk_branch_wait+0xf0/0x108
[ 33.286375] [<ffff00000849b2f4>] clk_branch2_disable+0x28/0x34
[ 33.291761] [<ffff0000084868dc>] clk_core_disable+0x5c/0x88
[ 33.297660] [<ffff000008487d68>] clk_core_disable_lock+0x20/0x34
[ 33.303129] [<ffff000008487d98>] clk_disable+0x1c/0x24
[ 33.309384] [<ffff0000083ccd78>] qcom_qmp_phy_poweroff+0x20/0x48
[ 33.314328] [<ffff0000083c53f4>] phy_power_off+0x80/0xdc
[ 33.320492] [<ffff00000875c950>] dwc3_core_exit+0x94/0xa0
[ 33.325784] [<ffff00000875c9ac>] dwc3_suspend_common+0x50/0x60
[ 33.331080] [<ffff00000875ca04>] dwc3_runtime_suspend+0x48/0x6c
[ 33.336810] [<ffff0000085b82f4>] pm_generic_runtime_suspend+0x28/0x38
[ 33.342627] [<ffff0000085bace0>] __rpm_callback+0x150/0x254
[ 33.349222] [<ffff0000085bae08>] rpm_callback+0x24/0x78
[ 33.354604] [<ffff0000085b9fd8>] rpm_suspend+0xe0/0x4e4
[ 33.359813] [<ffff0000085bb784>] pm_runtime_work+0xdc/0xf0
[ 33.365028] [<ffff0000080d7b30>] process_one_work+0x12c/0x28c
[ 33.370576] [<ffff0000080d7ce8>] worker_thread+0x58/0x3b8
[ 33.376393] [<ffff0000080dd4a8>] kthread+0x100/0x12c
[ 33.381776] [<ffff0000080836c0>] ret_from_fork+0x10/0x50
Fix this by disabling it as the first thing in phy_exit().
Fixes: e78f3d15e1 ("phy: qcom-qmp: new qmp phy driver for qcom-chipsets")
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add combo phy driver for HiSilicon STB SoCs. This phy can be
used as pcie-phy, sata-phy or usb-phy.
Changes for v5:
- Add bindings doc for Hi3798CV200 peripheral controller, and refer to
the bindings of this parent node in combphy bindings doc.
Changes for v4:
- Instead of relying on device id, add a new property
hisilicon,fixed-mode for combphy device that doesn't support mode
select but a fixed phy mode.
- Move combphy mode select register bits definition to device tree, as
it may vary from one device to another.
Changes for v3:
- Make combphy device be child of peripheral controller and use 'reg'
property for mapping combphy configuration registers.
- Kill "hisilicon,peripheral-syscon" property, since parent node is
just the syscon controller now.
- Check combphy id to handle the quirk that combphy0 can not configure
mode but always works in USB3 mode.
- Unify phy .init and .exit hooks for different combphy instances and
work modes, as the only quirk we need to handle is that combphy0 can
only work in USB3 mode.
- Better naming for clock and reset, 'ref' to 'ref_clk', 'por' to
'por_rst'.
Changes for v2:
- Move DT bindings into a separate patch.
- Drop the spurious newline from drivers/phy/Makefile.
- Use the phy type defines in dt-bindings/phy/phy.h.
- Use PTR_ERR_OR_ZERO() for checking return from
devm_of_phy_provider_register().
- Add USB3 phy support.
Signed-off-by: Jianguo Sun <sunjianguo1@huawei.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Allwinner R40 features a USB PHY like the one in A64, but with 3 PHYs.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Hermann Lauer <Hermann.Lauer@iwr.uni-heidelberg.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The assignment of map to itself is redundant and can be removed.
Detected with Coccinelle.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This converts from using a platform device for the CFGCHIP syscon
regmap to using platform data to pass the regmap to consumers.
A lazy getter function is used so that the regmap will only be
created if it is actually used. This function will also be used
in the clock init when we convert to the common clock framework.
The USB PHY driver is currently the only consumer. This driver is
updated to use platform data to get the CFGCHIP regmap instead of
syscon_regmap_lookup_by_pdevname().
Signed-off-by: David Lechner <david@lechnology.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This renames the clock con_ids in the DA8XX USB PHY driver as well as
the matching names in the mach clock registration code.
This is in preparation for using device tree clocks where these names
will become part of the device tree bindings. The new names more closely
match the names used in the USB clock diagram in the SoC TRM.
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Here is the big USB and PHY driver update for 4.16-rc1.
Along with the normally expected XHCI, MUSB, and Gadget driver patches,
there are some PHY driver fixes, license cleanups, sysfs attribute
cleanups, usbip changes, and a raft of other smaller fixes and
additions.
Full details are in the shortlog.
All of these have been in the linux-next tree for a long time with no
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWnL0Bg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymg8gCeLg/FMtc0S/xRR/56N/sbthEebcUAnROr9Sg3
55hDLdkyi93o9R86YOAJ
=8d2q
-----END PGP SIGNATURE-----
Merge tag 'usb-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big USB and PHY driver update for 4.16-rc1.
Along with the normally expected XHCI, MUSB, and Gadget driver
patches, there are some PHY driver fixes, license cleanups, sysfs
attribute cleanups, usbip changes, and a raft of other smaller fixes
and additions.
Full details are in the shortlog.
All of these have been in the linux-next tree for a long time with no
reported issues"
* tag 'usb-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (137 commits)
USB: serial: pl2303: new device id for Chilitag
USB: misc: fix up some remaining DEVICE_ATTR() usages
USB: musb: fix up one odd DEVICE_ATTR() usage
USB: atm: fix up some remaining DEVICE_ATTR() usage
USB: move many drivers to use DEVICE_ATTR_WO
USB: move many drivers to use DEVICE_ATTR_RO
USB: move many drivers to use DEVICE_ATTR_RW
USB: misc: chaoskey: Use true and false for boolean values
USB: storage: remove old wording about how to submit a change
USB: storage: remove invalid URL from drivers
usb: ehci-omap: don't complain on -EPROBE_DEFER when no PHY found
usbip: list: don't list devices attached to vhci_hcd
usbip: prevent bind loops on devices attached to vhci_hcd
USB: serial: remove redundant initializations of 'mos_parport'
usb/gadget: Fix "high bandwidth" check in usb_gadget_ep_match_desc()
usb: gadget: compress return logic into one line
usbip: vhci_hcd: update 'status' file header and format
USB: serial: simple: add Motorola Tetra driver
CDC-ACM: apply quirk for card reader
usb: option: Add support for FS040U modem
...
Pull libata updates from Tejun Heo:
"Nothing too interesting. Several patches to convert mdelay() to
usleep_range(), removal of unused pata_at32, and other low level
driver specific changes"
* 'for-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ata: pata_pdc2027x: Replace mdelay with msleep
ata: pata_it821x: Replace mdelay with usleep_range in it821x_firmware_command
ata: sata_mv: Replace mdelay with usleep_range in mv_reset_channel
ata: remove pata_at32
phy: brcm-sata: remove unused variable
phy: brcm-sata: fix semicolon.cocci warnings
ata: ahci_brcm: Recover from failures to identify devices
phy: brcm-sata: Implement calibrate callback
ahci: Add Intel Cannon Lake PCH-H PCI ID
ata_piix: constify pci_bits
libata:pata_atiixp: Don't use unconnected secondary port on SB600
ata: ahci_brcm: Avoid clobbering SATA_TOP_CTRL_BUS_CTRL
ahci: Allow setting a default LPM policy for mobile chipsets
ahci: Add PCI ids for Intel Bay Trail, Cherry Trail and Apollo Lake AHCI
ahci: Annotate PCI ids for mobile Intel chipsets as such
Stefan Wahren reports a problem with a warning fix that was merged
for v4.15: we had lots of device nodes with a 'phys' property pointing
to a device node that is not compliant with the binding documented in
Documentation/devicetree/bindings/phy/phy-bindings.txt
This generally works because USB HCD drivers that support both the generic
phy subsystem and the older usb-phy subsystem ignore most errors from
phy_get() and related calls and then use the usb-phy driver instead.
However, it turns out that making the usb-nop-xceiv device compatible with
the generic-phy binding changes the phy_get() return code from -EINVAL to
-EPROBE_DEFER, and the dwc2 usb controller driver for bcm2835 now returns
-EPROBE_DEFER from its probe function rather than ignoring the failure,
breaking all USB support on raspberry-pi when CONFIG_GENERIC_PHY is
enabled. The same code is used in the dwc3 driver and the usb_add_hcd()
function, so a reasonable assumption would be that many other platforms
are affected as well.
I have reviewed all the related patches and concluded that "usb-nop-xceiv"
is the only USB phy that is affected by the change, and since it is by far
the most commonly referenced phy, all the other USB phy drivers appear
to be used in ways that are are either safe in DT (they don't use the
'phys' property), or in the driver (they already ignore -EPROBE_DEFER
from generic-phy when usb-phy is available).
To work around the problem, this adds a special case to _of_phy_get()
so we ignore any PHY node that is compatible with "usb-nop-xceiv",
as we know that this can never load no matter how much we defer. In the
future, we might implement a generic-phy driver for "usb-nop-xceiv"
and then remove this workaround.
Since we generally want older kernels to also want to work with the
fixed devicetree files, it would be good to backport the patch into
stable kernels as well (3.13+ are possibly affected), even though they
don't contain any of the patches that may have caused regressions.
Fixes: 014d6da6cb ARM: dts: bcm283x: Fix DTC warnings about missing phy-cells
Fixes: c5bbf358b7 arm: dts: nspire: Add missing #phy-cells to usb-nop-xceiv
Fixes: 44e5dced2e arm: dts: marvell: Add missing #phy-cells to usb-nop-xceiv
Fixes: f568f6f554 ARM: dts: omap: Add missing #phy-cells to usb-nop-xceiv
Fixes: d745d5f277 ARM: dts: imx51-zii-rdu1: Add missing #phy-cells to usb-nop-xceiv
Fixes: 915fbe59cb ARM: dts: imx: Add missing #phy-cells to usb-nop-xceiv
Link: https://marc.info/?l=linux-usb&m=151518314314753&w=2
Link: https://patchwork.kernel.org/patch/10158145/
Cc: stable@vger.kernel.org
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Eric Anholt <eric@anholt.net>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The newly introduced calibrate function has a variable
that has never been used and needs to be removed to avoid
this harmless warning:
drivers/phy/broadcom/phy-brcm-sata.c: In function 'brcm_stb_sata_calibrate':
drivers/phy/broadcom/phy-brcm-sata.c:514:24: error: unused variable 'priv' [-Werror=unused-variable]
Fixes: 3e507769d1 ("phy: brcm-sata: Implement calibrate callback")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Implement the calibration callback to allow turning on the Clock-Data
Recovery module clamping when necessary, e.g: during failure to identify
a SATA hard drive from ahci_brcm.c::brcm_ahci_read_id.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
*) Fix in exynos5-usbdrd to enumerate SuperSpeed devices on Odroid XU3
*) Fix in Broadcom USB PHY to get Dell Low Speed keyboards working
*) Fix in Broadcom USB PHY to power down the PHY when XHCI disabled
to save power
*) Fix in Broadcom USB PHY to prevent abort in DRD mode
*) Fix in Broadcom USB PHY to use the correct dt properties
*) Fix in Mediatek PHY to detect device connection
*) Make getting resource optional for Mediatek V1 TPHY
*) Cleanup in Mediatek PHY
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJaSzimAAoJEA5ceFyATYLZrCUP/3f02fVtkF+OAL3e+ZwgCWy/
xoGIHffTcrYFimPeHh7INbeA16o2qNcN8JxJqQFFpZtZIoBR60az6ql7P2CZomXv
Z4S8ftKl8cOEI6O6AmLgRFuxaHSG24IxD54rHwCa6bDAoq36VnHM2CG+EEB6Yd3M
4eYoS1hQuwFCKeWSmHo4Uq8zyvTwIaxfKhOBlonXZu3/Tt34ZR0sGr3FC2OIamTN
Isrx/BsdHsfg+mTElos9jnc5/Uhwy/r7JFmRotn06cWGw2EGoM6EOXBrp3WXHD/f
jQnSSP3ZKmDvq0zY7QywXVo+fVWddZYx3fsbd26A5bUsarcj2VWlbHWyAWtYty3N
HOuucYbMHSXTFxP/0j6pwONzQIIucisGgNdUc4Zc7nzwcF8A/BWrEMkGqZLit45q
NalvVz/+lk0be3zZngm/vbaztHbHMQDvKe0U5QbHH9h47MybmydocrPgs7JbDcFd
P0vHJ1be5CMItcElC0w+fkrRf3tk5IYQb4nZFDaTRSiuLU+S+mgLfYjbGH4lXtnQ
USsGRv827wFqQVEzay2WvazvviBautoneh2+YDMg7R1cSOh9kQkunPl9ePOig/DR
Cgy1MEZH8GZIIhIOBshnLQ2FiQbtnn0NkDTOajLNyJssFbE+9XXYKJr/cUvCOArP
W9GjMMvI06gI7T+sDylY
=f9so
-----END PGP SIGNATURE-----
Merge tag 'phy-for-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 4.16
*) Fix in exynos5-usbdrd to enumerate SuperSpeed devices on Odroid XU3
*) Fix in Broadcom USB PHY to get Dell Low Speed keyboards working
*) Fix in Broadcom USB PHY to power down the PHY when XHCI disabled
to save power
*) Fix in Broadcom USB PHY to prevent abort in DRD mode
*) Fix in Broadcom USB PHY to use the correct dt properties
*) Fix in Mediatek PHY to detect device connection
*) Make getting resource optional for Mediatek V1 TPHY
*) Cleanup in Mediatek PHY
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
reduce the boilerplate code to get the specific data
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
V1 TPHY for SATA doesn't have shared banks if it isn't shared
with PCIe or USB, so make it optional.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
When system is running, if usb2 phy is forced to bypass utmi signals,
all PLL will be turned off, and it can't detect device connection
anymore, so replace force mode with auto mode which can bypass utmi
signals automatically if no device attached for normal flow.
But keep the force mode to fix RX sensitivity degradation issue.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This is caused by a bug in the BDC core. When the BDC core comes
out of reset and it's not selected, it gets a backup clock. When
the BDC core is selected, it get's the main clock. If HOST mode
is then selected the BDC core has the main clock shut off but
the backup clock is not restored.
The failure scenario and cause are as follows:
- DRD mode is active
- Device mode is selected first in bootloader
- When host mode is now selected, the clock to the BDC is cut off.
- BDC registers are inaccessible and therefore the BDC driver
crashes upon Linux boot.
The fix is to have the phy driver always force a BDC reset on
startup.
Fixes: 49859e55e3 ("phy: usb: phy-brcm-usb: Add Broadcom STB USB phy driver")
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Set PHY3_IDDQ_OVERRIDE in the xhci uninit routine. This will save
additional power when the XHCI driver is not enabled.
Fixes: 49859e55e3 ("phy: usb: phy-brcm-usb: Add Broadcom STB USB phy driver")
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Enable the the Low Speed Keep Alive signal on the 7271b0 by setting
the LS_KEEP_ALIVE bit in the USB CTRL OBRIDGE register otherwise
some Dell Low Speed keyboards fail.
Also do a little cleanup of the EBRIDGE ESTOP_SCB_REQ bit. Since
this is only used on one platform, remove it from the platform
tables and just use "if (family == ").
Fixes: 49859e55e3 ("phy: usb: phy-brcm-usb: Add Broadcom STB USB phy driver")
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Change "brcm,has_xhci" and "brcm,has_eohci" device tree properties
to the preferred "brcm,has-xhci" and "brcm,has-eohci". This also
matches the existing device tree bindings document.
Fixes: 49859e55e3 ("phy: usb: phy-brcm-usb: Add Broadcom STB USB phy driver")
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Adding phy calibration sequence for USB 3.0 DRD PHY present on
Exynos5420/5800 systems.
This calibration facilitates setting certain PHY parameters viz.
the Loss-of-Signal (LOS) Detector Threshold Level, as well as
Tx-Vboost-Level for Super-Speed operations.
Additionally we also set proper time to wait for RxDetect measurement,
for desired PHY reference clock, so as to solve issue with enumeration
of few USB 3.0 devices, like Samsung SUM-TSB16S 3.0 USB drive
on the controller.
We are using CR_port for this purpose to send required data
to override the LOS values.
On testing with USB 3.0 devices on USB 3.0 port present on
SMDK5420, and peach-pit boards should see following message:
usb 2-1: new SuperSpeed USB device number 2 using xhci-hcd
and without this patch, should see below shown message:
usb 1-1: new high-speed USB device number 2 using xhci-hcd
[Also removed unnecessary extra lines in the register macro definitions]
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
[adapted to use phy_calibrate as entry point]
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
When USB is disabled, we get a link error for this driver
because of the added OTG support
drivers/phy/renesas/phy-rcar-gen3-usb2.o: In function `rcar_gen3_phy_usb2_probe':
phy-rcar-gen3-usb2.c:(.text+0x250): undefined reference to `of_usb_get_dr_mode_by_phy'
Other phy drivers select USB_COMMON for this, so let's do the same
here.
Fixes: 7e0540f413 ("phy: rcar-gen3-usb2: check dr_mode for otg mode")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add pm_runtime_disable in err case to make the pm_runtime_enable/disable
is invoked balanced.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The platform_get_irq_byname() function returns negative if an error occurs.
zero or positive number on success. platform_get_irq_byname() error
checking for zero is not correct.
Fixes: 6d6ce40f63 ("phy: cpcap-usb: Add CPCAP PMIC USB support")
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Fix child-node lookups during probe, which ended up searching the whole
device tree depth-first starting at the parents rather than just
matching on their children.
To make things worse, some parent nodes could end up being being
prematurely freed (by tegra_xusb_pad_register()) as
of_find_node_by_name() drops a reference to its first argument.
Fixes: 53d2a715c2 ("phy: Add Tegra XUSB pad controller support")
Cc: stable <stable@vger.kernel.org> # 4.7
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Here is the big set of USB and PHY driver updates for 4.15-rc1.
There is the usual amount of gadget and xhci driver updates, along with
phy and chipidea enhancements. There's also a lot of SPDX tags and
license boilerplate cleanups as well, which provide some churn in the
diffstat.
Other major thing is the typec code that moved out of staging and into
the "real" part of the drivers/usb/ tree, which was nice to see happen.
All of these have been in linux-next with no reported issues for a
while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWgm/Vw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yktXwCdGgpInfOEvOGFd83EPDL7a1ncyc4AoM5wI8yl
1CeLipqVIN3IsMMJptvb
=zvDI
-----END PGP SIGNATURE-----
Merge tag 'usb-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big set of USB and PHY driver updates for 4.15-rc1.
There is the usual amount of gadget and xhci driver updates, along
with phy and chipidea enhancements. There's also a lot of SPDX tags
and license boilerplate cleanups as well, which provide some churn in
the diffstat.
Other major thing is the typec code that moved out of staging and into
the "real" part of the drivers/usb/ tree, which was nice to see
happen.
All of these have been in linux-next with no reported issues for a
while"
* tag 'usb-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (263 commits)
usb: gadget: f_fs: Fix use-after-free in ffs_free_inst
USB: usbfs: compute urb->actual_length for isochronous
usb: core: message: remember to reset 'ret' to 0 when necessary
USB: typec: Remove remaining redundant license text
USB: typec: add SPDX identifiers to some files
USB: renesas_usbhs: rcar?.h: add SPDX tags
USB: chipidea: ci_hdrc_tegra.c: add SPDX line
USB: host: xhci-debugfs: add SPDX lines
USB: add SPDX identifiers to all remaining Makefiles
usb: host: isp1362-hcd: remove a couple of redundant assignments
USB: adutux: remove redundant variable minor
usb: core: add a new usb_get_ptm_status() helper
usb: core: add a 'type' parameter to usb_get_status()
usb: core: introduce a new usb_get_std_status() helper
usb: core: rename usb_get_status() 'type' argument to 'recip'
usb: core: add Status Type definitions
USB: gadget: Remove redundant license text
USB: gadget: function: Remove redundant license text
USB: gadget: udc: Remove redundant license text
USB: gadget: legacy: Remove redundant license text
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Detailed description for this pull request:
1. Split out extcon header file for consumer and provider device
: The extcon has two type of extcon devices as following.
- 'extcon provider deivce' adds new extcon device and detect
the state/properties of external connector. Also, it notifies the
state/properties to the extcon consumer device.
- 'extcon consumer device' gets the change state/properties
from extcon provider device.
Prior to that, include/linux/extcon.h contains all exported API
for both provider and consumer device driver. To clarify the meaning
of header file and to remove the wrong use-case on consumer device.
- include/linux/extcon-provider.h includes API for the provider device driver.
- include/linux/extcon.h includes the API for the consumer device driver.
2. Support the SmartDock accessory on extcon-max77843.c device driver
- Support the SmartDock accessory which detects following connectors
at the same time.
: USB host throught USB hub for mouse, keyboard and so on.
: MHL connector for video output.
: Charger connector for battery charging.
- It tested with Unitek Y-2165 MHL+OTG Hub Smart Phone Dock.
3. Fix the minor issue of extcon driver
- Delete the unneeded initialization in extcon-max14577.
- Make extcon_info static const in order to fix the warning.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gWvl
-----END PGP SIGNATURE-----
Merge tag 'extcon-next-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon into usb-next
Chanwoo writes:
Update extcon for 4.15
Detailed description for this pull request:
1. Split out extcon header file for consumer and provider device
: The extcon has two type of extcon devices as following.
- 'extcon provider deivce' adds new extcon device and detect
the state/properties of external connector. Also, it notifies the
state/properties to the extcon consumer device.
- 'extcon consumer device' gets the change state/properties
from extcon provider device.
Prior to that, include/linux/extcon.h contains all exported API
for both provider and consumer device driver. To clarify the meaning
of header file and to remove the wrong use-case on consumer device.
- include/linux/extcon-provider.h includes API for the provider device driver.
- include/linux/extcon.h includes the API for the consumer device driver.
2. Support the SmartDock accessory on extcon-max77843.c device driver
- Support the SmartDock accessory which detects following connectors
at the same time.
: USB host throught USB hub for mouse, keyboard and so on.
: MHL connector for video output.
: Charger connector for battery charging.
- It tested with Unitek Y-2165 MHL+OTG Hub Smart Phone Dock.
3. Fix the minor issue of extcon driver
- Delete the unneeded initialization in extcon-max14577.
- Make extcon_info static const in order to fix the warning.
Some quirky UDCs (like dwc3 on Exynos) need to have their phys calibrated e.g.
for using super speed. This patch adds a new phy_calibrate() method.
When the calibration should be used is dependent on actual chip.
In case of dwc3 on Exynos the calibration must happen after usb_add_hcd()
(while in host mode), because certain phy parameters like Tx LOS levels
and boost levels need to be calibrated further post initialization of xHCI
controller, to get SuperSpeed operations working. But an hcd must be
prepared first in order to pass it to usb_add_hcd(), so, in particular, dwc3
registers must be available first, and in order for the latter to happen
the phys must be initialized. This poses a chicken and egg problem if
the calibration were to be performed in phy_init(). To break the circular
dependency a separate method is added which can be called at a desired
moment after phy intialization.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Refactor ufs_qcom_power_up_sequence() to get rid of ugly
exported phy APIs and use the phy_init() and phy_power_on()
to do the phy initialization.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Adding support to set desired UFS phy mode that can be set
from the host controller.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Update the PCIe phy settings based on new settings available
in AM572x Technical Reference Manual[1] Revision I, revised
April 2017 in Table 26-62 "Preferred PCIe_PHY_RX SCP Register
Settings".
[1] http://www.ti.com/lit/ug/spruhz6i/spruhz6i.pdf
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[nsekhar@ti.com: commit message updates]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Parse the DT properties brcm,rxaeq-mode and brcm,rxaeq-value to
correctly configure the RX equalizer of the PHY. This may be required to
resolve specific signal integrity issues.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Split the functional code in brcm_stb_sata_init() to a separate function
that actually does configure spread spectrum: brcm_stb_sata_ssc_init()
and make that function return void, since that function cannot fail.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch adds SoC-specific parameter to avoid reading/writing
specific registers wrongly if this driver runs on a SoC which doesn't
have dedicated pins (e.g. R-Car D3). This patch also changes the
value "has_otg" to "has_otg_pins" for slightly easier reading of
the code.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch modifies the role_store() to use "enum phy_mode" instead
of the local "bool" for host/device mode selection.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The previous code assumed a channel has otg capability if a channel
has interrupt property. But, it is not good because:
- Battery charging feature also needs interrupt property.
- Some R-Car Gen3 SoCs (e.g. R-Car D3) don't have OTG capability.
So, this patch checks whether usb 2.0 host node has dr_mode property or
not. If it has 'dr_mode = "otg";', this driver enables otg capability.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Allwinner V3s SoC also features the dual route of the first USB PHY.
Enable it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Calculate the calibration code as per the docs. The docs talk about
reading and averaging the pullup and pulldown calibration codes. They
also talk about adding in some adjustment codes. Let's do what the
docs say.
In practice this doesn't seem to matter a whole lot. On a device I
tested the pullup and pulldown codes were nearly the same (0x23 and
0x24) and the adjustment codes were 0.
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
NOTE: nothing is known to be fixed by this change, but it does enforce
some delays that are documented to be necessary. Possibly this could
fix some corner cases.
The function tcphy_dp_aux_calibration(), like most of the functions in
the type C PHY, is mostly undocumented and filled with mysterious,
hardcoded numbers.
Let's attempt to try to document some of these numbers and clean the
function up a little bit. Here's the actual cleanup that happened
here:
1. All magic numbers were replaced with bit definitions.
2. For registers that we modify multiple times I now keep track of the
value of the register rather than randomly doing a
read/modify/write or just hardcoding a new number based on knowing
what the old number was.
3. Delay 10 ms (vs 1 ms) after writing the calibration code. No idea
if this is important but it matches the example in the docs.
4. Whenever setting a "delayed" version of a signal always put an
explicit delay in the code. No known problems were seen without
this delay but it seems wise to have it. Whenever a delay of "at
least 100 ns" was specified I used a delay of 1 us.
5. Added comments to some of the bits of code.
6. Removed duplicate setting of TX_ANA_CTRL_REG_5 (to 0)
7. Moved setting of TX_ANA_CTRL_REG_3 to the same place it was in the
sample code. Note that TX_ANA_CTRL_REG_3 ought to be initted to 0
(and elsewhere we assume that we just got a reset), but it seems
fine to be explicit.
8. Treats the calibration code as a 7-bit two's complement number.
This isn't strictly required, but seems slightly cleaner. The docs
say "treat this as a two's complement number, but it should never
be negative". If we ever read the "adjustment" codes as documented
then perhaps the two's complement bit will matter more.
There are still a few weird / mysterious things around aux init and
this doesn't attempt to fix all of them. Mostly it's aimed at doing
changes that should be _very_ safe and add a lot of clarity. Things
specifically not done:
A) Resolve the fact that some registers are read/modify/write and
others are explicitly initted to a value. We always call
tcphy_dp_aux_calibration() right after resetting the PHY so it's
probably not critical, but it's a little weird that the code is
inconsistent.
B) Fully resolve the documented init sequence with the current one.
We still have a few mystery steps and we also leave out turning on
TXDA_DRV_LDO_BG_FB_EN and TXDA_DRV_LDO_BG_REF_EN, which is in the
sample code.
C) Clean things up to read all the bits of the calibration code. This
will hopefully come in a followup change.
This also doesn't attempt to document any of the other parts of the
PHY--just the aux init which is all I got docs for.
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This is used to force PHY with USB OTG function to enter a specific
mode, and override OTG IDPIN(or IDDIG) signal.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The 'modes' member of the mvebu_comphy_priv structure is not used.
Remove it.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The extcon has two type of extcon devices as following.
- 'extcon provider deivce' adds new extcon device and detect the
state/properties of external connector. Also, it notifies the
state/properties to the extcon consumer device.
- 'extcon consumer device' gets the change state/properties
from extcon provider device.
Prior to that, include/linux/extcon.h contains all exported API for
both provider and consumer device driver. To clarify the meaning of
header file and to remove the wrong use-case on consumer device,
this patch separates into extcon.h and extcon-provider.h.
[Description for include/linux/{extcon.h|extcon-provider.h}]
- extcon.h includes the extcon API and data structure for extcon consumer
device driver. This header file contains the following APIs:
: Register/unregister the notifier to catch the change of extcon device
: Get the extcon device instance
: Get the extcon device name
: Get the state of each external connector
: Get the property value of each external connector
: Get the property capability of each external connector
- extcon-provider.h includes the extcon API and data structure for extcon
provider device driver. This header file contains the following APIs:
: Include 'include/linux/extcon.h'
: Allocate the memory for extcon device instance
: Register/unregister extcon device
: Set the state of each external connector
: Set the property value of each external connector
: Set the property capability of each external connector
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
The function tcphy_phy_init() could return an error but the callers
weren't checking the return value. They should. In at least one case
while testing I saw the message "wait pma ready timeout" which
indicates that tcphy_phy_init() really could return an error and we
should account for it.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
When the usb phy device mode is set to "drd", the USB port will
switch between device and host modes depending on what's plugged
into the port. Customers have asked for the ability to force
host or device mode from software. This commit adds sysfs
entries to the phy device that allow this. The sysfs for the phy
device can be found at:
/sys/bus/platform/drivers/brcmstb-usb-phy/*.usb-phy
The following sysfs entries were added:
- "dr_mode" (RO) - The current phy "dr_mode" setting.
It will be set to one of the following values:
- "host" - host mode
- "peripheral " - device mode
- "drd" - switch between device and host mode based on
installed device
- "typec-pd" - device/host mode is controller by the USB
Type-C PD protocol.
If "dr_mode" is "drd"
- "drd_select" (RW) -
It will be set to one of the following values:
- "host" - force host mode
- "device" - force device mode
- "auto" - allow normal auto selection of host/device based on
inserted USB device
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add a new USB Phy driver for Broadcom STB SoCs. This driver
supports Broadcom STB ARM SoCs. This driver in
combination with the Broadcom STB ohci, ehci and xhci
drivers will enable USB1.1, USB2.0 and USB3.0 support.
This Phy driver also supports the Broadcom BDC gadget
driver.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
On rk3399-gru-kevin there are some cases where we're seeing AUX CH
failures when trying to do DisplayPort over type C. Problems are
intermittent and don't reproduce all the time. Problems are often
bursty and failures persist for several seconds before going away.
The failure case I focused on is:
* A particular type C to HDMI adapter.
* One orientation (flip mode) of that adapter.
* Easier to see failures when something is plugged into the _other
type C port at the same time.
* Problems reproduce on both type C ports (left and right side).
Ironically problems also stop reproducing when I solder wires onto the
AUX CH signals on a port (even if no scope is connected to the
signals). In this case, problems only stop reproducing on the port
with the wires connected.
From the above it appears that something about the signaling on the
aux channel is marginal and any slight differences can bring us over
the edge to failure.
It turns out that we can fix our problems by just increasing the
voltage swing of the AUX CH, giving us a bunch of extra margin. In DP
up to version 1.2 the voltage swing on the aux channel was specced as
.29 V to 1.38 V. In DP version 1.3 the aux channel voltage was
tightened to be between .29 V and .40 V, but it clarifies that it
really only needs the lower voltage when operating at the highest
speed (HBR3 mode). So right now we are trying to use a voltage that
technically should be valid for all versions of the spec (including
version 1.3 when transmitting at HBR3). That would be great to do if
it worked reliably. ...but it doesn't seem to.
It turns out that if you continue to read through the DP part of the
rk3399 TRM and other parts of the type C PHY spec you'll find out that
while the rk3399 does support DP 1.3, it doesn't support HBR3. The
docs specifically say "RBR, HBR and HBR2 data rates only". Thus there
is actually no requirement to support an AUX CH swing of .4 V.
Even if there is no actual requirement to support the tighter voltage
swing, one could possibly argue that we should support it anyway. The
DP spec clarifies that the lower voltage on the AUX CH will reduce
cross talk in some cases and that seems like it could be beneficial
even at the lower bit rates. At the moment, though, we are seeing
problems with the AUX CH and not on the other lines. Also, checking
another known working and similar laptop shows that the other laptop
runs the AUX channel at a higher voltage.
Other notes:
* Looking at measurements done on the AUX CH we weren't actually
compliant with the DP 1.3 spec anyway. AUX CH peek-to-peek voltage
was measured on rk3399-gru-kevin as .466 V which is > .4 V.
* With this new patch the AUX channel isn't actually 1.0 V, but it has
been confirmed that the signal is better and has more margin. Eye
diagram passes.
* If someone were truly an expert in the Type C PHY and in DisplayPort
signaling they might be able to make things work and keep the
voltage at < .4 V. The Type C PHY seems to have a plethora of
tuning knobs that could almost certainly improve the signal
integrity. Some of these things (like enabling tx_fcm_full_margin)
even seem to fix my problems. However, lacking expertise I can't
say whether this is a better or worse solution. Tightening signals
to give cleaner waveforms can often have adverse affects, like
increasing EMI or adding noise to other signals. I'd rather not
tune things like this without a healthy application of expertise
that I don't have.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
On some DP monitors we found that setting the wrong flip state on the
AUX channel could cause the monitor to stop asserting HotPlug Detect
(HPD). Setting the right flip state caused these monitors to start
asserting HotPlug Detect again.
Here's what we believe was happening:
* We'd plug in the monitor and we'd see HPD assert
* We'd quickly see HPD deassert
* The kernel would try to init the type C PHY but would init it in USB
mode (because there was a peripheral there but no HPD)
* Because the kernel never set the flip mode properly we'd never see
the HPD come back.
With this change, we'll still see HPD disappear (we don't think
there's anything we can do about that), but then it will come back.
Overall we can say that it's sane to set the AUX channel flip state
even when HPD is not asserted.
NOTE: to make this change possible, I needed to do a bit of cleanup to
the tcphy_dp_aux_calibration() function so that it doesn't ever
clobber the FLIP state. This made it very obvious that a line of code
documented as "setting bit 12" also did a bunch of other magic,
undocumented stuff. For now I'll just break out the bits and add a
comment that this is black magic and we'll try to document
tcphy_dp_aux_calibration() better in a future CL.
ALSO NOTE: the old function used to write a bunch of hardcoded
values in _some_ cases instead of doing a read-modify-write. One
could possibly assert that these could have had (beneficial) side
effects and thus with this new code (which always does
read-modify-write) we could have a bug. We shouldn't need to worry,
though, since in the old code tcphy_dp_aux_calibration() was always
called following the de-assertion of "reset" the the type C PHY.
...so the type C PHY was always in default state. TX_ANA_CTRL_REG_1
is documented to be 0x0 after reset. This was also confirmed by
printk.
Suggested-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
devm_ioremap_resource() never returns NULL, it only returns error
pointers so this test needs to be changed.
Fixes: d0438bd6aa ("phy: add the mvebu cp110 comphy driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The pipe selector is used to select some modes (such as USB or PCIe).
Otherwise it must be set to 0 (or "unconnected"). This patch does this
to ensure it is not set to an incompatible value when using the
supported modes (SGMII, 10GKR).
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The mux value is retrieved from the mvebu_comphy_get_mux() function
which returns an int. In mvebu_comphy_power_on() this int is stored to a
u32 and a check is made to ensure it's not negative. Which is wrong.
This fixes it.
Fixes: d0438bd6aa ("phy: add the mvebu cp110 comphy driver")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Chip bank of version-1 is initialized as NULL, but it's used
by pcie_phy_instance_power_on/off(), so assign it a right
address.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
kasprintf() can fail and it's return value must be checked.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for 4.14 for MIPS; below a summary of
the non-merge commits:
CM:
- Rename mips_cm_base to mips_gcr_base
- Specify register size when generating accessors
- Use BIT/GENMASK for register fields, order & drop shifts
- Add cluster & block args to mips_cm_lock_other()
CPC:
- Use common CPS accessor generation macros
- Use BIT/GENMASK for register fields, order & drop shifts
- Introduce register modify (set/clear/change) accessors
- Use change_*, set_* & clear_* where appropriate
- Add CM/CPC 3.5 register definitions
- Use GlobalNumber macros rather than magic numbers
- Have asm/mips-cps.h include CM & CPC headers
- Cluster support for topology functions
- Detect CPUs in secondary clusters
CPS:
- Read GIC_VL_IDENT directly, not via irqchip driver
DMA:
- Consolidate coherent and non-coherent dma_alloc code
- Don't use dma_cache_sync to implement fd_cacheflush
FPU emulation / FP assist code:
- Another series of 14 commits fixing corner cases such as NaN
propgagation and other special input values.
- Zero bits 32-63 of the result for a CLASS.D instruction.
- Enhanced statics via debugfs
- Do not use bools for arithmetic. GCC 7.1 moans about this.
- Correct user fault_addr type
Generic MIPS:
- Enhancement of stack backtraces
- Cleanup from non-existing options
- Handle non word sized instructions when examining frame
- Fix detection and decoding of ADDIUSP instruction
- Fix decoding of SWSP16 instruction
- Refactor handling of stack pointer in get_frame_info
- Remove unreachable code from force_fcr31_sig()
- Convert to using %pOF instead of full_name
- Remove the R6000 support.
- Move FP code from *_switch.S to *_fpu.S
- Remove unused ST_OFF from r2300_switch.S
- Allow platform to specify multiple its.S files
- Add #includes to various files to ensure code builds reliable and
without warning..
- Remove __invalidate_kernel_vmap_range
- Remove plat_timer_setup
- Declare various variables & functions static
- Abstract CPU core & VP(E) ID access through accessor functions
- Store core & VP IDs in GlobalNumber-style variable
- Unify checks for sibling CPUs
- Add CPU cluster number accessors
- Prevent direct use of generic_defconfig
- Make CONFIG_MIPS_MT_SMP default y
- Add __ioread64_copy
- Remove unnecessary inclusions of linux/irqchip/mips-gic.h
GIC:
- Introduce asm/mips-gic.h with accessor functions
- Use new GIC accessor functions in mips-gic-timer
- Remove counter access functions from irq-mips-gic.c
- Remove gic_read_local_vp_id() from irq-mips-gic.c
- Simplify shared interrupt pending/mask reads in irq-mips-gic.c
- Simplify gic_local_irq_domain_map() in irq-mips-gic.c
- Drop gic_(re)set_mask() functions in irq-mips-gic.c
- Remove gic_set_polarity(), gic_set_trigger(), gic_set_dual_edge(),
gic_map_to_pin() and gic_map_to_vpe() from irq-mips-gic.c.
- Convert remaining shared reg access, local int mask access and
remaining local reg access to new accessors
- Move GIC_LOCAL_INT_* to asm/mips-gic.h
- Remove GIC_CPU_INT* macros from irq-mips-gic.c
- Move various definitions to the driver
- Remove gic_get_usm_range()
- Remove __gic_irq_dispatch() forward declaration
- Remove gic_init()
- Use mips_gic_present() in place of gic_present and remove
gic_present
- Move gic_get_c0_*_int() to asm/mips-gic.h
- Remove linux/irqchip/mips-gic.h
- Inline __gic_init()
- Inline gic_basic_init()
- Make pcpu_masks a per-cpu variable
- Use pcpu_masks to avoid reading GIC_SH_MASK*
- Clean up mti, reserved-cpu-vectors handling
- Use cpumask_first_and() in gic_set_affinity()
- Let the core set struct irq_common_data affinity
microMIPS:
- Fix microMIPS stack unwinding on big endian systems
MIPS-GIC:
- SYNC after enabling GIC region
NUMA:
- Remove the unused parent_node() macro
R6:
- Constify r2_decoder_tables
- Add accessor & bit definitions for GlobalNumber
SMP:
- Constify smp ops
- Allow boot_secondary SMP op to return errors
VDSO:
- Drop gic_get_usm_range() usage
- Avoid use of linux/irqchip/mips-gic.h
Platform changes:
Alchemy:
- Add devboard machine type to cpuinfo
- update cpu feature overrides
- Threaded carddetect irqs for devboards
AR7:
- allow NULL clock for clk_get_rate
BCM63xx:
- Fix ENETDMA_6345_MAXBURST_REG offset
- Allow NULL clock for clk_get_rate
CI20:
- Enable GPIO and RTC drivers in defconfig
- Add ethernet and fixed-regulator nodes to DTS
Generic platform:
- Move Boston and NI 169445 FIT image source to their own files
- Include asm/bootinfo.h for plat_fdt_relocated()
- Include asm/time.h for get_c0_*_int()
- Include asm/bootinfo.h for plat_fdt_relocated()
- Include asm/time.h for get_c0_*_int()
- Allow filtering enabled boards by requirements
- Don't explicitly disable CONFIG_USB_SUPPORT
- Bump default NR_CPUS to 16
JZ4700:
- Probe the jz4740-rtc driver from devicetree
Lantiq:
- Drop check of boot select from the spi-falcon driver.
- Drop check of boot select from the lantiq-flash MTD driver.
- Access boot cause register in the watchdog driver through regmap
- Add device tree binding documentation for the watchdog driver
- Add docs for the RCU DT bindings.
- Convert the fpi bus driver to a platform_driver
- Remove ltq_reset_cause() and ltq_boot_select(
- Switch to a proper reset driver
- Switch to a new drivers/soc GPHY driver
- Add an USB PHY driver for the Lantiq SoCs using the RCU module
- Use of_platform_default_populate instead of __dt_register_buses
- Enable MFD_SYSCON to be able to use it for the RCU MFD
- Replace ltq_boot_select() with dummy implementation.
Loongson 2F:
- Allow NULL clock for clk_get_rate
Malta:
- Use new GIC accessor functions
NI 169445:
- Add support for NI 169445 board.
- Only include in 32r2el kernels
Octeon:
- Add support for watchdog of 78XX SOCs.
- Add support for watchdog of CN68XX SOCs.
- Expose support for mips32r1, mips32r2 and mips64r1
- Enable more drivers in config file
- Add support for accessing the boot vector.
- Remove old boot vector code from watchdog driver
- Define watchdog registers for 70xx, 73xx, 78xx, F75xx.
- Make CSR functions node aware.
- Allow access to CIU3 IRQ domains.
- Misc cleanups in the watchdog driver
Omega2+:
- New board, add support and defconfig
Pistachio:
- Enable Root FS on NFS in defconfig
Ralink:
- Add Mediatek MT7628A SoC
- Allow NULL clock for clk_get_rate
- Explicitly request exclusive reset control in the pci-mt7620 PCI driver.
SEAD3:
- Only include in 32 bit kernels by default
VoCore:
- Add VoCore as a vendor t0 dt-bindings
- Add defconfig file"
* '4.14-features' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (167 commits)
MIPS: Refactor handling of stack pointer in get_frame_info
MIPS: Stacktrace: Fix microMIPS stack unwinding on big endian systems
MIPS: microMIPS: Fix decoding of swsp16 instruction
MIPS: microMIPS: Fix decoding of addiusp instruction
MIPS: microMIPS: Fix detection of addiusp instruction
MIPS: Handle non word sized instructions when examining frame
MIPS: ralink: allow NULL clock for clk_get_rate
MIPS: Loongson 2F: allow NULL clock for clk_get_rate
MIPS: BCM63XX: allow NULL clock for clk_get_rate
MIPS: AR7: allow NULL clock for clk_get_rate
MIPS: BCM63XX: fix ENETDMA_6345_MAXBURST_REG offset
mips: Save all registers when saving the frame
MIPS: Add DWARF unwinding to assembly
MIPS: Make SAVE_SOME more standard
MIPS: Fix issues in backtraces
MIPS: jz4780: DTS: Probe the jz4740-rtc driver from devicetree
MIPS: Ci20: Enable RTC driver
watchdog: octeon-wdt: Add support for 78XX SOCs.
watchdog: octeon-wdt: Add support for cn68XX SOCs.
watchdog: octeon-wdt: File cleaning.
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9cLP
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.14-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- add enhanced Downstream Port Containment support, which prints more
details about Root Port Programmed I/O errors (Dongdong Liu)
- add Layerscape ls1088a and ls2088a support (Hou Zhiqiang)
- add MediaTek MT2712 and MT7622 support (Ryder Lee)
- add MediaTek MT2712 and MT7622 MSI support (Honghui Zhang)
- add Qualcom IPQ8074 support (Varadarajan Narayanan)
- add R-Car r8a7743/5 device tree support (Biju Das)
- add Rockchip per-lane PHY support for better power management (Shawn
Lin)
- fix IRQ mapping for hot-added devices by replacing the
pci_fixup_irqs() boot-time design with a host bridge hook called at
probe-time (Lorenzo Pieralisi, Matthew Minter)
- fix race when enabling two devices that results in upstream bridge
not being enabled correctly (Srinath Mannam)
- fix pciehp power fault infinite loop (Keith Busch)
- fix SHPC bridge MSI hotplug events by enabling bus mastering
(Aleksandr Bezzubikov)
- fix a VFIO issue by correcting PCIe capability sizes (Alex
Williamson)
- fix an INTD issue on Xilinx and possibly other drivers by unifying
INTx IRQ domain support (Paul Burton)
- avoid IOMMU stalls by marking AMD Stoney GPU ATS as broken (Joerg
Roedel)
- allow APM X-Gene device assignment to guests by adding an ACS quirk
(Feng Kan)
- fix driver crashes by disabling Extended Tags on Broadcom HT2100
(Extended Tags support is required for PCIe Receivers but not
Requesters, and we now enable them by default when Requesters support
them) (Sinan Kaya)
- fix MSIs for devices that use phantom RIDs for DMA by assuming MSIs
use the real Requester ID (not a phantom RID) (Robin Murphy)
- prevent assignment of Intel VMD children to guests (which may be
supported eventually, but isn't yet) by not associating an IOMMU with
them (Jon Derrick)
- fix Intel VMD suspend/resume by releasing IRQs on suspend (Scott
Bauer)
- fix a Function-Level Reset issue with Intel 750 NVMe by waiting
longer (up to 60sec instead of 1sec) for device to become ready
(Sinan Kaya)
- fix a Function-Level Reset issue on iProc Stingray by working around
hardware defects in the CRS implementation (Oza Pawandeep)
- fix an issue with Intel NVMe P3700 after an iProc reset by adding a
delay during shutdown (Oza Pawandeep)
- fix a Microsoft Hyper-V lockdep issue by polling instead of blocking
in compose_msi_msg() (Stephen Hemminger)
- fix a wireless LAN driver timeout by clearing DesignWare MSI
interrupt status after it is handled, not before (Faiz Abbas)
- fix DesignWare ATU enable checking (Jisheng Zhang)
- reduce Layerscape dependencies on the bootloader by doing more
initialization in the driver (Hou Zhiqiang)
- improve Intel VMD performance allowing allocation of more IRQ vectors
than present CPUs (Keith Busch)
- improve endpoint framework support for initial DMA mask, different
BAR sizes, configurable page sizes, MSI, test driver, etc (Kishon
Vijay Abraham I, Stan Drozd)
- rework CRS support to add periodic messages while we poll during
enumeration and after Function-Level Reset and prepare for possible
other uses of CRS (Sinan Kaya)
- clean up Root Port AER handling by removing unnecessary code and
moving error handler methods to struct pcie_port_service_driver
(Christoph Hellwig)
- clean up error handling paths in various drivers (Bjorn Andersson,
Fabio Estevam, Gustavo A. R. Silva, Harunobu Kurokawa, Jeffy Chen,
Lorenzo Pieralisi, Sergei Shtylyov)
- clean up SR-IOV resource handling by disabling VF decoding before
updating the corresponding resource structs (Gavin Shan)
- clean up DesignWare-based drivers by unifying quirks to update Class
Code and Interrupt Pin and related handling of write-protected
registers (Hou Zhiqiang)
- clean up by adding empty generic pcibios_align_resource() and
pcibios_fixup_bus() and removing empty arch-specific implementations
(Palmer Dabbelt)
- request exclusive reset control for several drivers to allow cleanup
elsewhere (Philipp Zabel)
- constify various structures (Arvind Yadav, Bhumika Goyal)
- convert from full_name() to %pOF (Rob Herring)
- remove unused variables from iProc, HiSi, Altera, Keystone (Shawn
Lin)
* tag 'pci-v4.14-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (170 commits)
PCI: xgene: Clean up whitespace
PCI: xgene: Define XGENE_PCI_EXP_CAP and use generic PCI_EXP_RTCTL offset
PCI: xgene: Fix platform_get_irq() error handling
PCI: xilinx-nwl: Fix platform_get_irq() error handling
PCI: rockchip: Fix platform_get_irq() error handling
PCI: altera: Fix platform_get_irq() error handling
PCI: spear13xx: Fix platform_get_irq() error handling
PCI: artpec6: Fix platform_get_irq() error handling
PCI: armada8k: Fix platform_get_irq() error handling
PCI: dra7xx: Fix platform_get_irq() error handling
PCI: exynos: Fix platform_get_irq() error handling
PCI: iproc: Clean up whitespace
PCI: iproc: Rename PCI_EXP_CAP to IPROC_PCI_EXP_CAP
PCI: iproc: Add 500ms delay during device shutdown
PCI: Fix typos and whitespace errors
PCI: Remove unused "res" variable from pci_resource_io()
PCI: Correct kernel-doc of pci_vpd_srdt_size(), pci_vpd_srdt_tag()
PCI/AER: Reformat AER register definitions
iommu/vt-d: Prevent VMD child devices from being remapping targets
x86/PCI: Use is_vmd() rather than relying on the domain number
...
- RK805 Power Management IC (PMIC)
- ROHM BD9571MWV-M MFD Power Management IC (PMIC)
- Texas Instruments TPS68470 Power Management IC (PMIC) & LEDs
- New Device Support
- Add support for HiSilicon Hi6421v530 to hi6421-pmic-core
- Add support for X-Powers AXP806 to axp20x
- Add support for X-Powers AXP813 to axp20x
- Add support for Intel Sunrise Point LPSS to intel-lpss-pci
- New Functionality
- Amend API to provide register layout; atmel-smc
- Fix-ups
- DT re-work; omap, nokia
- Header file location change {I2C => MFD}; dm355evm_msp, tps65010
- Fix chip ID formatting issue(s); rk808
- Optionally register touchscreen devices; da9052-core
- Documentation improvements; twl-core
- Constification; rtsx_pcr, ab8500-core, da9055-i2c, da9052-spi
- Drop unnecessary static declaration; max8925-i2c
- Kconfig changes (missing deps and remove module support)
- Slim down oversized licence statement; hi6421-pmic-core
- Use managed resources (devm_*); lp87565
- Supply proper error checking/handling; t7l66xb
- Bug Fixes
- Fix counter duplication issue; da9052-core
- Fix potential NULL deference issue; max8998
- Leave SPI-NOR write-protection bit alone; lpc_ich
- Ensure device is put into reset during suspend; intel-lpss
- Correct register offset variable size; omap-usb-tll
-----BEGIN PGP SIGNATURE-----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=TKIm
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers
- RK805 Power Management IC (PMIC)
- ROHM BD9571MWV-M MFD Power Management IC (PMIC)
- Texas Instruments TPS68470 Power Management IC (PMIC) & LEDs
New Device Support:
- Add support for HiSilicon Hi6421v530 to hi6421-pmic-core
- Add support for X-Powers AXP806 to axp20x
- Add support for X-Powers AXP813 to axp20x
- Add support for Intel Sunrise Point LPSS to intel-lpss-pci
New Functionality:
- Amend API to provide register layout; atmel-smc
Fix-ups:
- DT re-work; omap, nokia
- Header file location change {I2C => MFD}; dm355evm_msp, tps65010
- Fix chip ID formatting issue(s); rk808
- Optionally register touchscreen devices; da9052-core
- Documentation improvements; twl-core
- Constification; rtsx_pcr, ab8500-core, da9055-i2c, da9052-spi
- Drop unnecessary static declaration; max8925-i2c
- Kconfig changes (missing deps and remove module support)
- Slim down oversized licence statement; hi6421-pmic-core
- Use managed resources (devm_*); lp87565
- Supply proper error checking/handling; t7l66xb
Bug Fixes:
- Fix counter duplication issue; da9052-core
- Fix potential NULL deference issue; max8998
- Leave SPI-NOR write-protection bit alone; lpc_ich
- Ensure device is put into reset during suspend; intel-lpss
- Correct register offset variable size; omap-usb-tll"
* tag 'mfd-next-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (61 commits)
mfd: intel_soc_pmic: Differentiate between Bay and Cherry Trail CRC variants
mfd: intel_soc_pmic: Export separate mfd-cell configs for BYT and CHT
dt-bindings: mfd: Add bindings for ZII RAVE devices
mfd: omap-usb-tll: Fix register offsets
mfd: da9052: Constify spi_device_id
mfd: intel-lpss: Put I2C and SPI controllers into reset state on suspend
mfd: da9055: Constify i2c_device_id
mfd: intel-lpss: Add missing PCI ID for Intel Sunrise Point LPSS devices
mfd: t7l66xb: Handle return value of clk_prepare_enable
mfd: Add ROHM BD9571MWV-M PMIC DT bindings
mfd: intel_soc_pmic_chtwc: Turn Kconfig option into a bool
mfd: lp87565: Convert to use devm_mfd_add_devices()
mfd: Add support for TPS68470 device
mfd: lpc_ich: Do not touch SPI-NOR write protection bit on Haswell/Broadwell
mfd: syscon: atmel-smc: Add helper to retrieve register layout
mfd: axp20x: Use correct platform device ID for many PEK
dt-bindings: mfd: axp20x: Introduce bindings for AXP813
mfd: axp20x: Add support for AXP813 PMIC
dt-bindings: mfd: axp20x: Add AXP806 to supported list of chips
mfd: Add ROHM BD9571MWV-M MFD PMIC driver
...
Pull networking updates from David Miller:
1) Support ipv6 checksum offload in sunvnet driver, from Shannon
Nelson.
2) Move to RB-tree instead of custom AVL code in inetpeer, from Eric
Dumazet.
3) Allow generic XDP to work on virtual devices, from John Fastabend.
4) Add bpf device maps and XDP_REDIRECT, which can be used to build
arbitrary switching frameworks using XDP. From John Fastabend.
5) Remove UFO offloads from the tree, gave us little other than bugs.
6) Remove the IPSEC flow cache, from Florian Westphal.
7) Support ipv6 route offload in mlxsw driver.
8) Support VF representors in bnxt_en, from Sathya Perla.
9) Add support for forward error correction modes to ethtool, from
Vidya Sagar Ravipati.
10) Add time filter for packet scheduler action dumping, from Jamal Hadi
Salim.
11) Extend the zerocopy sendmsg() used by virtio and tap to regular
sockets via MSG_ZEROCOPY. From Willem de Bruijn.
12) Significantly rework value tracking in the BPF verifier, from Edward
Cree.
13) Add new jump instructions to eBPF, from Daniel Borkmann.
14) Rework rtnetlink plumbing so that operations can be run without
taking the RTNL semaphore. From Florian Westphal.
15) Support XDP in tap driver, from Jason Wang.
16) Add 32-bit eBPF JIT for ARM, from Shubham Bansal.
17) Add Huawei hinic ethernet driver.
18) Allow to report MD5 keys in TCP inet_diag dumps, from Ivan
Delalande.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1780 commits)
i40e: point wb_desc at the nvm_wb_desc during i40e_read_nvm_aq
i40e: avoid NVM acquire deadlock during NVM update
drivers: net: xgene: Remove return statement from void function
drivers: net: xgene: Configure tx/rx delay for ACPI
drivers: net: xgene: Read tx/rx delay for ACPI
rocker: fix kcalloc parameter order
rds: Fix non-atomic operation on shared flag variable
net: sched: don't use GFP_KERNEL under spin lock
vhost_net: correctly check tx avail during rx busy polling
net: mdio-mux: add mdio_mux parameter to mdio_mux_init()
rxrpc: Make service connection lookup always check for retry
net: stmmac: Delete dead code for MDIO registration
gianfar: Fix Tx flow control deactivation
cxgb4: Ignore MPS_TX_INT_CAUSE[Bubble] for T6
cxgb4: Fix pause frame count in t4_get_port_stats
cxgb4: fix memory leak
tun: rename generic_xdp to skb_xdp
tun: reserve extra headroom only when XDP is set
net: dsa: bcm_sf2: Configure IMP port TC2QOS mapping
net: dsa: bcm_sf2: Advertise number of egress queues
...
Here is the big char/misc driver update for 4.14-rc1.
Lots of different stuff in here, it's been an active development cycle
for some reason. Highlights are:
- updated binder driver, this brings binder up to date with what
shipped in the Android O release, plus some more changes that
happened since then that are in the Android development trees.
- coresight updates and fixes
- mux driver file renames to be a bit "nicer"
- intel_th driver updates
- normal set of hyper-v updates and changes
- small fpga subsystem and driver updates
- lots of const code changes all over the driver trees
- extcon driver updates
- fmc driver subsystem upadates
- w1 subsystem minor reworks and new features and drivers added
- spmi driver updates
Plus a smattering of other minor driver updates and fixes.
All of these have been in linux-next with no reported issues for a
while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWa1+Ew8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yl26wCgquufNylfhxr65NbJrovduJYzRnUAniCivXg8
bePIh/JI5WxWoHK+wEbY
=hYWx
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big char/misc driver update for 4.14-rc1.
Lots of different stuff in here, it's been an active development cycle
for some reason. Highlights are:
- updated binder driver, this brings binder up to date with what
shipped in the Android O release, plus some more changes that
happened since then that are in the Android development trees.
- coresight updates and fixes
- mux driver file renames to be a bit "nicer"
- intel_th driver updates
- normal set of hyper-v updates and changes
- small fpga subsystem and driver updates
- lots of const code changes all over the driver trees
- extcon driver updates
- fmc driver subsystem upadates
- w1 subsystem minor reworks and new features and drivers added
- spmi driver updates
Plus a smattering of other minor driver updates and fixes.
All of these have been in linux-next with no reported issues for a
while"
* tag 'char-misc-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (244 commits)
ANDROID: binder: don't queue async transactions to thread.
ANDROID: binder: don't enqueue death notifications to thread todo.
ANDROID: binder: Don't BUG_ON(!spin_is_locked()).
ANDROID: binder: Add BINDER_GET_NODE_DEBUG_INFO ioctl
ANDROID: binder: push new transactions to waiting threads.
ANDROID: binder: remove proc waitqueue
android: binder: Add page usage in binder stats
android: binder: fixup crash introduced by moving buffer hdr
drivers: w1: add hwmon temp support for w1_therm
drivers: w1: refactor w1_slave_show to make the temp reading functionality separate
drivers: w1: add hwmon support structures
eeprom: idt_89hpesx: Support both ACPI and OF probing
mcb: Fix an error handling path in 'chameleon_parse_cells()'
MCB: add support for SC31 to mcb-lpc
mux: make device_type const
char: virtio: constify attribute_group structures.
Documentation/ABI: document the nvmem sysfs files
lkdtm: fix spelling mistake: "incremeted" -> "incremented"
perf: cs-etm: Fix ETMv4 CONFIGR entry in perf.data file
nvmem: include linux/err.h from header
...
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
On the CP110 unit, which can be found on various Marvell platforms such
as the 7k and 8k (currently), a comphy (common PHYs) hardware block can
be found. This block provides a number of PHYs which can be used in
various modes by other controllers (network, SATA ...). These common
PHYs must be configured for the controllers using them to work correctly
either at boot time, or when the system runs to switch the mode used.
This patch adds a driver for this comphy hardware block, providing
callbacks for the its PHYs so that consumers can configure the modes
used.
As of this commit, two modes are supported by the comphy driver: sgmii
and 10gkr.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reconstruct the whole driver to support per-lane PHYs. Note that we could
also support the legacy PHY if you don't provide argument to
rockchip_pcie_phy_of_xlate().
Tested-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
[bhelgaas: use postincrement/decrement when order doesn't matter, uninline
to_pcie_phy() so decl fits on one line]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Detailed description for this pull request:
1. Add new 'extcon-usbc-cros-ec.c' driver
- ChromeOS Embedded Controller extcon driver supports
the detection of the Display Port (EXTCON_DISP_DP)
through USB C-type and contol it.
2. Update extcon core
- Modify the description for both functions and structures
in order to improve the readability and give the more correct
guide about the role of functions because there are different
explanation even if the same arguments.
- Keep the indentation with tab instead of space
- Remove the following deprecated extcon API. The deprecated API
are exchanged on all of linux tree.
: extcon_get_cable_state_() -> extcon_get_state()
: extcon_set_cable_state_() -> extcon_set_state_sync()
3. Include the two immutable branch as following:
- ib-extcon-mfd-4.14 for the 'extcon-ubsc-cros-ec.c' driver
because the patches of 'extcon-ubsc-cros-ec.c' touch the MFD directory.
- ib-extcon-usb-phy-4.14 for removing the deprecated extcon API
because the usb/phy driver usese the deprecated extcon API.
So, this immutable branch alters the extcon API and then
remove them from extcon.
4. Fix minor issue of extcon driver
- Fix the MHL detection on extcon-max77693.c
- Convert to using %pOF instead of full_name on extcon.c
- Add 'const' kerywod for acpi_device_id on extcon-intel-int3496.c
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=oQMu
-----END PGP SIGNATURE-----
Merge tag 'extcon-next-for-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon into char-misc-next
Chanwoo writes:
Update extcon for 4.14
Detailed description for this pull request:
1. Add new 'extcon-usbc-cros-ec.c' driver
- ChromeOS Embedded Controller extcon driver supports
the detection of the Display Port (EXTCON_DISP_DP)
through USB C-type and contol it.
2. Update extcon core
- Modify the description for both functions and structures
in order to improve the readability and give the more correct
guide about the role of functions because there are different
explanation even if the same arguments.
- Keep the indentation with tab instead of space
- Remove the following deprecated extcon API. The deprecated API
are exchanged on all of linux tree.
: extcon_get_cable_state_() -> extcon_get_state()
: extcon_set_cable_state_() -> extcon_set_state_sync()
3. Include the two immutable branch as following:
- ib-extcon-mfd-4.14 for the 'extcon-ubsc-cros-ec.c' driver
because the patches of 'extcon-ubsc-cros-ec.c' touch the MFD directory.
- ib-extcon-usb-phy-4.14 for removing the deprecated extcon API
because the usb/phy driver usese the deprecated extcon API.
So, this immutable branch alters the extcon API and then
remove them from extcon.
4. Fix minor issue of extcon driver
- Fix the MHL detection on extcon-max77693.c
- Convert to using %pOF instead of full_name on extcon.c
- Add 'const' kerywod for acpi_device_id on extcon-intel-int3496.c
Casting between an 'int' and a pointer causes a warning on
64-bit architectures in compile-testing this driver:
drivers/phy/ralink/phy-ralink-usb.c: In function 'ralink_usb_phy_probe':
drivers/phy/ralink/phy-ralink-usb.c:195:13: error: cast from pointer to
integer of different size [-Werror=pointer-to-int-cast]
This changes the code to cast to uintptr_t instead. This is
guaranteed to do what we want on all architectures and avoids
the warning.
Fixes: 2411a736ff ("phy: ralink-usb: add driver for Mediatek/Ralink")
Acked-by: John Crispin <john@phrozen.org>
Tested-by Harvey Hunt <harvey.hunt@imgtec.com>
Reviewed-by Harvey Hunt <harvey.hunt@imgtec.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
*) Add USB PHY driver for Ralink SoC
*) Make phy-mt65xx-usb3 driver support PCIe and SATA phy
*) Add mediatek directory and rename phy-mt65xx-usb3 to phy-mtk-tphy.c
since it now supports USB3.0, PCIe and SATA PHYs
*) Make sun4i-usb-phy driver support USB PHYs for A83T SoC
*) Make phy-qcom-qmp driver support USB PHYs for IPQ8074 SoC
*) Make rockchip-inno-usb2 driver support usb2-phy for rv1108 SoC
*) Minor fixes in phy drivers
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=SckR
-----END PGP SIGNATURE-----
Merge tag 'phy-for-4.14_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 4.14
*) Add USB PHY driver for Ralink SoC
*) Make phy-mt65xx-usb3 driver support PCIe and SATA phy
*) Add mediatek directory and rename phy-mt65xx-usb3 to phy-mtk-tphy.c
since it now supports USB3.0, PCIe and SATA PHYs
*) Make sun4i-usb-phy driver support USB PHYs for A83T SoC
*) Make phy-qcom-qmp driver support USB PHYs for IPQ8074 SoC
*) Make rockchip-inno-usb2 driver support usb2-phy for rv1108 SoC
*) Minor fixes in phy drivers
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
We want to timeout with try set to zero so this should be a pre-op
instead of post-op.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This line was indented further that it should have been.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The "check" variable isn't necessarily initialized when we print it out
in the debugging messages. It's a pretty haphazard affair and it
doesn't matter very much what we initialize "check" to.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
In order to silent the 'W=1' compile warning:
drivers/phy/rockchip/phy-rockchip-typec.c: In function 'tcphy_get_mode':
drivers/phy/rockchip/phy-rockchip-typec.c:625:7: warning: variable 'dfp'
set but not used [-Wunused-but-set-variable]
Cc: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This adds support usb2-phy for rv1108 SoCs and amend phy Documentation.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The otg-id/otg-bvalid/linestate interrupts are multiplexed together
in otg-port on some Rockchip SoC (e.g RV1108), this patch add support
for it.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The registers of usb-phy are distributed in grf and usbgrf on some
Rockchip SoCs (e.g RV1108), this patch add a new rockchip,usbgrf
property to support this companion grf design.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The A83T has 3 USB PHYs, 1 for OTG, 1 for standard USB, 1 for USB HSIC.
The phy initialization procedure is very different from other SoCs, but
the PMU bits are the same, with additional bits for HSIC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
On the Allwinner A83T SoC, the last USB PHY is an HSIC PHY. It requires
two clocks instead of one.
On all Allwinner SoCs that share the common USB PHY design supported by
the phy-sun4i-usb driver, the first PHY is always tied to OTG, and there
is at most one HSIC PHY, typically the last.
In this patch we take advantage of these known constraints and store an
index in the compatible-string-related config structure describing which
PHY is HSIC, needing the extra hsic_12M clock.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add a driver to setup the USB phy on Mediatek/Ralink SoCs.
The driver sets up power and host mode, but also needs to
configure PHY registers for the MT7628 and MT7688.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
reduce the boilerplate code to get the specific data
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The driver is actually for T-PHY which supports USB3.0, PCIe and SATA,
and supports more SoCs now, but not just only for series of mt65xx SoCs,
so the name of file, data struct, functions etc with 'mt65xx' may cause
misunderstanding when new SoCs are supported. Here rename them to reflect
the real functions and also enhance readability.
And also update MAINTAINERS file to reflect the correct driver
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch adds SATA setting part.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The AM572x Technical Reference Manual, SPRUHZ6H,
Revised November 2016 [1], shows recommended settings for the
SATA DPLL in Table 26-8. DPLL CLKDCOLDO Recommended Settings.
Use those settings in the driver. The TRM does not show
a value for 20MHz SYS_CLK so we use something close to the
26MHz setting.
[1] - http://www.ti.com/lit/ug/spruhz6h/spruhz6h.pdf
Signed-off-by: Roger Quadros <rogerq@ti.com>
[nsekhar@ti.com: add exact TRM version to commit text]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Fixing the clk enable failure path in qcom_qmp_phy_init()
and cleanup the reset control deassertion failure path in
qcom_qmp_phy_com_init().
Fixes: e78f3d15e1 ("phy: qcom-qmp: new qmp phy driver for qcom-chipsets")
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add definitions required to enable QMP phy support for IPQ8074.
Signed-off-by: smuthayy <smuthayy@codeaurora.org>
Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Presently, the phy pipe clock's name is assumed to be either
usb3_phy_pipe_clk_src or pcie_XX_pipe_clk_src (where XX is the
phy lane's number). However, this will not work if an SoC has
more than one instance of the phy. Hence, instead of assuming
the name of the clock, fetch it from the DT.
Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch replaces the deprecated extcon API as following:
- extcon_set_cable_state_() -> extcon_get_state()
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch uses the resource-managed extcon API for extcon_register_notifier()
and replaces the deprecated extcon API as following:
- extcon_get_cable_state_() -> extcon_get_state()
- extcon_set_cable_state_() -> extcon_set_state_sync()
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The driver attempts to 'select MDIO_DEVICE', but the code
is actually a loadable module when PHYLIB=m:
drivers/phy/broadcom/phy-bcm-ns-usb3.o: In function `bcm_ns_usb3_mdiodev_phy_write':
phy-bcm-ns-usb3.c:(.text.bcm_ns_usb3_mdiodev_phy_write+0x28): undefined reference to `mdiobus_write'
drivers/phy/broadcom/phy-bcm-ns-usb3.o: In function `bcm_ns_usb3_module_exit':
phy-bcm-ns-usb3.c:(.exit.text+0x18): undefined reference to `mdio_driver_unregister'
drivers/phy/broadcom/phy-bcm-ns-usb3.o: In function `bcm_ns_usb3_module_init':
phy-bcm-ns-usb3.c:(.init.text+0x18): undefined reference to `mdio_driver_register'
phy-bcm-ns-usb3.c:(.init.text+0x38): undefined reference to `mdio_driver_unregister'
Using 'depends on MDIO_BUS' instead will avoid the link error.
Fixes: af850e14a7 ("phy: bcm-ns-usb3: add MDIO driver using proper bus layer")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When phy-sun4i-usb's probing fails, it does not print the reason in
kernel log, forcing the developer to edit this driver to add info logs.
This commit makes the kernel print the reason of phy-sun4i-usb's probing
failure or a success message.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Tested-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch uses the resource-managed extcon API for extcon_register_notifier()
and replaces the deprecated extcon API as following:
- (deprecated) extcon_get_cable_state_() -> extcon_get_state()
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
As USB 3.0 PHY is attached to the MDIO bus this module should provide a
MDIO driver and use a proper bus layer. This is a proper (cleaner)
solution which doesn't require code to know this specific MDIO bus
details. It also allows reusing the driver with other MDIO buses.
For now keep platform device support in place. We may consider dropping
it once MDIO bindings gets used "everywhere".
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
When we finally start using MDIO layer then bus initialization will be
handled in a separated driver. It means our code handling this has to be
used for the platform driver only.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Our current writing function accesses PHY directly bypassing MDIO layer.
The aim is to extend this module to also behave as MDIO driver. This
will require using different writing function which can be handled
cleanly by having an extra pointer like this.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Move MDIO specific code to the writing helper function. This makes init
code a bit more generic and doesn't require it to track what happens
after every write.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch adds support for stingray SATA phy in the
SATA BRCM phy driver.
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Commit 8ae904e3c236 ("phy: cpcap-usb: Add CPCAP PMIC USB support")
is missing return statement as noted by Colin Ian King
<colin.king@canonical.com>. If the optional pins are not configured,
we just want to return early and not attempt to configure the pins.
Fixes: 8ae904e3c236 ("phy: cpcap-usb: Add CPCAP PMIC USB support")
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This is driver for USB DRD PHY used in Broadcom's Northstar2
SoC. The phy can be configured to be in Device mode or Host
mode based on the type of cable connected to the port. The
driver registers to extcon framework to get appropriate
connect events for Host/Device cables connect/disconnect
states based on VBUS and ID interrupts.
Signed-off-by: Raviteja Garimella <raviteja.garimella@broadcom.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
When MUSB is a loadable module, we get a link error for a built-in
CPCAP driver:
drivers/phy/built-in.o: In function `cpcap_usb_phy_remove':
phy-cpcap-usb.c:(.text+0xed9): undefined reference to `musb_mailbox'
This adds a Kconfig dependency to prevent this broken configuration,
enforcing that CPCAP can only be a module when MUSB is also a module.
Fixes: 68a1f7c9d470 ("phy: cpcap-usb: Add CPCAP PMIC USB support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
->set_mode() can be used to tell PHY to prepare itself to enter USB
Host/Peripheral mode and that's very important for DRD
configurations.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
TUSB1211 is software compatible with TUSB1210 and as such we don't
need an entire new driver to control it. Let's add its product ID to
the existing TUSB1210 driver instead.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The USB 3.0 PHY modules of R-Car Gen3 SoCs have:
- Spread spectrum clock (ssc).
- Using USB 2.0 EXTAL clock instead of USB 3.0 clock.
- Enabling VBUS detection for usb3.0 peripheral.
So, this driver supports these features.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This adds support usb2-phy for rk3228 SoCs and amend phy Documentation.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
At the current rockchip-inno-usb2 phy driver framework, it can
only support usb2-phy which comprises with one otg-port and one
host-port.
However, some Rockchip SoCs' (e.g RK3228, RK3229) usb2-phy comprises
with two host-ports, so we use index of otg id for one host-port
configuration, and make it work the same as otg-port host mode.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
In rockchip-inno-usb2 phy driver, we use otg_sm_work to
dynamically manage power consumption for phy otg-port.
If the otg-port works as peripheral mode and does not
communicate with usb host, we will suspend phy.
But once suspend phy, the phy no longer has any internal
clock running, include the utmi_clk which supplied for
usb controller. So if we suspend phy before usb controller
init, it will cause usb controller fail to initialize.
Specifically, without this patch, the observed order is:
1. unplug usb cable
2. start system, do dwc2 controller probe
3. dwc2_lowlevel_hw_enable()
- phy_init()
- rockchip_usb2phy_init()
- schedule otg_sm_work after 2s
put phy in suspend, and close utmi_clk
4. dwc2_hsotg_udc_start() - fail to initialize the usb core
Generally, dwc2_hsotg_udc_start() can be called within 5s
after start system on Rockchip platform, so we increase the
the first schedule delay time to 6s for otg_sm_work afer usb
controller calls phy_init(), this can make sure that the usb
controller completes initialization before phy enter suspend.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
When resume phy, it need about 1.5 ~ 2ms to wait for
utmi_clk which used for USB controller to become stable.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Some Motorola phones like droid 4 use a custom CPCAP PMIC that has a
multiplexing USB PHY.
This USB PHY can operate at least in four modes using pin multiplexing
and two control GPIOS:
- Pass through companion PHY for the SoC USB PHY
- ULPI PHY for the SoC
- Pass through USB for the modem
- UART debug console for the SoC
This patch adds support for droid 4 USB PHY and debug UART modes,
support for other modes can be added later on as needed.
Both peripheral and host mode are working for the USB. The
host mode depends on the cpcap-charger driver for VBUS.
VBUS and ID pin detection are done using cpcap-adc IIO ADC
driver.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Meson8 uses the same USB PHY as found on the Meson8b and GXBB SoCs. Add
a new of_device_id to indicate this. Also update the Kconfig option and
MODULE_DESCRIPTION accordingly.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This adds a new driver for the USB2 PHYs found on Meson GXL and GXM SoCs
(both SoCs are using the same USB PHY register layout).
The USB2 PHY is a simple PHY which only has a few registers to configure
the mode (host/device) and a reset register (to enable/disable the PHY).
Unfortunately there are no datasheets available for this PHY. The driver
was written by reading the code from Amlogic's GPL kernel sources and
by analyzing the registers on an actual GXL and GXM device running the
kernel that was shipped on the boards I have.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Although ULPI phy is currently being used by tusb1210,
there can be other consumers too in future. So move this
to the includes path for phy.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Cc: Stephen Boyd <stephen.boyd@linaro.org>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
drivers/phy/qualcomm/phy-qcom-qmp.c:847:37-43: ERROR: application of sizeof to pointer
sizeof when applied to a pointer typed expression gives the size of
the pointer
Generated by: scripts/coccinelle/misc/noderef.cocci
CC: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
In case of error, the function of_iomap() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should
be replaced with NULL test.
Fixes: e78f3d15e1 ("phy: qcom-qmp: new qmp phy driver for qcom-chipsets")
Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
With CONFIG_NVMEM=m and CONFIG_PHY_QCOM_QUSB2=y we get a link error from
calls to devm_nvmem_cell_get and nvmem_cell_read:
drivers/built-in.o: In function `qusb2_phy_probe':
binder.c:(.text+0x4750): undefined reference to `devm_nvmem_cell_get'
drivers/built-in.o: In function `qusb2_phy_init':
binder.c:(.text+0x489c): undefined reference to `nvmem_cell_read'
Fix this by adding a Kconfig dependency to ensure we can only have this
driver built in when the nvmem functions are also built in or we see the
empty stub functions. We can still build this driver as a module when the
nvmem core is build as module, too.
Fixes: deffad633413 ("phy: qcom-qusb2: New driver for QUSB2 PHY on Qcom chips")
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
On rockchip devices vbus is supplied by a separate power supply, often
through a regulator. Add support for describing the the regulator in
device-tree following the same convention as several other usb phy's.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
So far all the PHY initialization was implemented using some totally
magic values. There was some pattern there but it wasn't clear what is
it about.
Thanks to the patch submitted by Broadcom:
[PATCH 5/6] phy: Add USB3 PHY support for Broadcom NSP SoC
and the upstream "iproc-mdio" driver we now know there is a MDIO bus
underneath with PHY(s) and their registers.
It allows us to clean the driver a bit by making all these values less
magical. The next step is switching to using a proper MDIO layer.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Qualcomm SOCs have QMP phy controller that provides support
to a number of controller, viz. PCIe, UFS, and USB.
Add a new driver, based on generic phy framework, for this
phy controller.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
PHY transceiver driver for QUSB2 phy controller that provides
HighSpeed functionality for DWC3 controller present on
Qualcomm chipsets.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add usb2-phy config information in the data of match table for
rk3328.
Signed-off-by: Meng Dongyang <daniel.meng@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
There will be a problem if SS port is diasbled and HS port extracts
100uA from SS port, so disable extract 100uA from SS port in the case,
when disable it, PA0_RG_USB20_INTR_EN should be set, otherwise HS port
only works on LS.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
There are some variations from mt2701 to mt2712:
1. banks shared by multiple ports are put back into each port,
such as SPLLC and U2FREQ;
2. add a new bank MISC for u2port, and CHIP for u3port;
3. bank's offset in each port are also rearranged;
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
each port has its own reference clock, the HighSpeed port is 48M,
and the SuperSpeed port is usually 26M, put them into port node for
flexibility, this can close clock if the port is not used.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Currently usb3 port in fact includes two sub-ports, but it is not
flexible for some cases, such as following one:
usb3 port0 includes u2port0 and u3port0;
usb2 port0 includes u2port1;
If wants to support only HS, we can use u2port0 or u2port1, when
select u2port0, u3port0 is not needed;
If wants to support SS, we can compound u2port0 and u3port0,
or u2port1 and u3port0, if select latter one, u2port0 is not needed.
So it's more flexible to split usb3 port into two ones and also try
best to save power by disabling unnecessary ports.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Increase LFPS filter threshold to avoid some fake remote wakeup
signal which cause U3 link fail and link to U2 only at about
0.01% probability.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The default value of RX detection stable time is 10us, and this
margin is too big for some critical cases which cause U3 link fail
and link to U2(probability is about 1%). So change it to 5us.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Allwinner A64 SoC features a switchable PHY0 like the one in H3, which
can switch between a MUSB controller and a pair of OHCI/EHCI controller.
Enable PHY0 route auto switching for A64.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch fixes an issue that this driver doesn't take care of the runtime
PM. This code assumed that devm_phy_create() called pm_runtime_enable(dev),
but it misunderstood the dev_phy_create()'s specification.
This driver should call its own pm_runtime_enable() before
dev_phy_create().
Fixes: f3b5a8d9b5 ("phy: rcar-gen3-usb2: Add R-Car Gen3 USB2 PHY driver")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
trivial fix to spelling mistake in dev_dbg message, also rejoin
lines to clean up checkpatch warning
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
There is no need for separate defines for Exynos4 and Exynos5 phy enable
bit and MIPI phy reset bits. In both cases there are the same so
simplify it.
This reduces number of defines and allows removal of one header file.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Exynos4 MIPI phy registers are defined with macro calculating the offset
for given phyN. Use the same method for Exynos5420 to be consistent.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Phy drivers access PMU region through regmap provided by exynos-pmu
driver. However there is no need to duplicate defines for PMU
registers. Instead just use whatever is defined in exynos-regs-pmu.h.
This reduces number of defines.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Phy drivers access PMU region through regmap provided by exynos-pmu
driver. However there is no need to duplicate defines for PMU
registers. Instead just use whatever is defined in exynos-regs-pmu.h.
Additionally MIPI PHY registers for Exynos5433 start from the same
address as Exynos4 and Exynos5250 so re-use existing defines.
This reduces number of defines and allows removal of one header file.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The register offsets for REG_DBG_UART (and all following) were off by
0x4. This was not a problem yet because these registers are currently
not used by the driver.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
On newer Allwinner SoCs (H3 and after), the PHY0 node is routed to both
MUSB controller for peripheral and host support (the host support is
slightly broken), and a pair of EHCI/OHCI controllers, which provide a
better support for host mode.
Add support for automatically switch the route of PHY0 according to the
status of dr_mode and id det pin.
Only H3 have this function enabled in this patch, as further SoCs will
be tested later and then have it enabled.
As H5 is reusing the PHY driver of H3, this function is also enabled.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The config structure of H3 in phy-sun4i-usb driver have the PHYCTL
register offset missing.
Add it. From the BSP source code, we know that the offset should be
0x10.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
It seems that all SoCs with the PHYCTL register offset as 0x10 need the
PHYCTL register to be cleared before it's written.
Change PHYCTL register clearing code to judge whether clearing is needed
based on the PHYCTL offset.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The Kconfig currently controlling compilation of this code is:
drivers/phy/Kconfig:config PHY_EXYNOS_PCIE
drivers/phy/Kconfig: bool "Exynos PCIe PHY driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Pankaj Dubey <pankaj.dubey@samsung.com>
Cc: Vivek Gautam <vivek.gautam@codeaurora.org>
Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
We get the following compile errors if EXTCON is enabled as a
module but this driver is builtin:
drivers/built-in.o: In function `qcom_usb_hs_phy_power_off':
phy-qcom-usb-hs.c:(.text+0x1089): undefined reference to `extcon_unregister_notifier'
drivers/built-in.o: In function `qcom_usb_hs_phy_probe':
phy-qcom-usb-hs.c:(.text+0x11b5): undefined reference to `extcon_get_edev_by_phandle'
drivers/built-in.o: In function `qcom_usb_hs_phy_power_on':
phy-qcom-usb-hs.c:(.text+0x128e): undefined reference to `extcon_get_state'
phy-qcom-usb-hs.c:(.text+0x12a9): undefined reference to `extcon_register_notifier'
so let's mark this as needing to follow the modular status of
the extcon framework.
Fixes: 9994a33865e2427b09ba (phy: Add support for Qualcomm's USB HS phy")
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
When it doesn't get the blk_base's resource, it was returned
the error about phy_base, not blk_base.
This patch is for fixing the wrong error return about blk_base.
Fixes: cf0adb8e28 ("phy: phy-exynos-pcie: Add support for Exynos PCIe PHY")
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This reverts commit d7bc1a7d41 ("phy: Add USB3 PHY support for
Broadcom NSP SoC") as we already have driver for this PHY (shared by NS
and NSP). It was added in commit e5666281d9 ("phy: bcm-ns-usb3: new
driver for USB 3.0 PHY on Northstar").
Instead of adding separated driver & duplicating code we should work on
improving existing (old) one. Thanks to work done by Broadcom we know
there is MDIO bus we weren't aware of & we know register names which
makes initialization more clear. This is very valuable info and we
should work on using it in existing driver afterwards.
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=4Owc
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- add ASPM L1 substate support
- enable PCIe Extended Tags when supported
- configure PCIe MPS settings on iProc, Versatile, X-Gene, and Xilinx
- increase VPD access timeout
- add ACS quirks for Intel Union Point, Qualcomm QDF2400 and QDF2432
- use new pci_irq_alloc_vectors() in more drivers
- fix MSI affinity memory leak
- remove unused MSI interfaces and update documentation
- remove unused AER .link_reset() callback
- avoid pci_lock / p->pi_lock deadlock seen with perf
- serialize sysfs enable/disable num_vfs operations
- move DesignWare IP from drivers/pci/host/ to drivers/pci/dwc/ and
refactor so we can support both hosts and endpoints
- add DT ECAM-like support for HiSilicon Hip06/Hip07 controllers
- add Rockchip system power management support
- add Thunder-X cn81xx and cn83xx support
- add Exynos 5440 PCIe PHY support
* tag 'pci-v4.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (93 commits)
PCI: dwc: Remove dependency of designware on CONFIG_PCI
PCI: dwc: Add CONFIG_PCIE_DW_HOST to enable PCI dwc host
PCI: dwc: Split pcie-designware.c into host and core files
PCI: dwc: designware: Fix style errors in pcie-designware.c
PCI: dwc: designware: Parse "num-lanes" property in dw_pcie_setup_rc()
PCI: dwc: all: Split struct pcie_port into host-only and core structures
PCI: dwc: designware: Get device pointer at the start of dw_pcie_host_init()
PCI: dwc: all: Rename cfg_read/cfg_write to read/write
PCI: dwc: all: Use platform_set_drvdata() to save private data
PCI: dwc: designware: Move register defines to designware header file
PCI: dwc: Use PTR_ERR_OR_ZERO to simplify code
PCI: dra7xx: Group PHY API invocations
PCI: dra7xx: Enable MSI and legacy interrupts simultaneously
PCI: dra7xx: Add support to force RC to work in GEN1 mode
PCI: dra7xx: Simplify probe code with devm_gpiod_get_optional()
PCI: Move DesignWare IP support to new drivers/pci/dwc/ directory
PCI: exynos: Support the PHY generic framework
Documentation: binding: Modify the exynos5440 PCIe binding
phy: phy-exynos-pcie: Add support for Exynos PCIe PHY
Documentation: samsung-phy: Add exynos-pcie-phy binding
...
Add support for Generic PHY framework about Exynos SoCs. Current Exynos
PCIe driver doesn't use the PHY framework, which makes it difficult to
upstream the other Exynos variants because of different PHY registers.
Move the codes relevant to PHY from Exnyos PCIe driver to PHY Exynos PCIe
driver.
[bhelgaas: depend on "OF && (ARCH_EXYNOS || COMPILE_TEST)", update
copyright year, both per Vivek]
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Jingoo Han <jingoohan1@gmail.com>
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We want to skip only tx/rx_iface clocks and not ref_clk_src
as well. Fix the jump label accordingly.
Fixes: 300f96771d ("phy: qcom-ufs: Skip obtaining rx/tx_iface_clk for msm8996 based phy")
Cc: Subhash Jadavani <subhashj@codeaurora.org>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: stable@vger.kernel.org
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Fix build errors in phy-rockchip-inno-usb2.c. The driver uses
extcon interfaces so it should depend on EXTCON.
Fixes these build errors:
drivers/built-in.o: In function `rockchip_usb2phy_otg_sm_work':
phy-rockchip-inno-usb2.c:(.text+0x2bcb): undefined reference to `extcon_get_state'
phy-rockchip-inno-usb2.c:(.text+0x2cd4): undefined reference to `extcon_set_state_sync'
phy-rockchip-inno-usb2.c:(.text+0x2cec): undefined reference to `extcon_set_state_sync'
phy-rockchip-inno-usb2.c:(.text+0x2d2d): undefined reference to `extcon_get_state'
drivers/built-in.o: In function `rockchip_usb2phy_probe':
phy-rockchip-inno-usb2.c:(.text+0x31d7): undefined reference to `extcon_get_edev_by_phandle'
phy-rockchip-inno-usb2.c:(.text+0x321a): undefined reference to `devm_extcon_dev_allocate'
phy-rockchip-inno-usb2.c:(.text+0x3230): undefined reference to `devm_extcon_dev_register'
phy-rockchip-inno-usb2.c:(.text+0x375a): undefined reference to `extcon_register_notifier'
Found in linux-next but is also needed in mainline.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch adds support for Broadcom NSP USB3 PHY
Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The error paths of the common qcom-ufs functions for registering the
phy, acquiring clocks and acquiring regulators all print specific error
messages before returning an error, so there is no value in printing yet
another - more generic - message when this occur.
Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The fact that a regulator is always-on is a property of the regulator,
not a specific consumer. Implementing this in the driver leads to a
system behaviour that is dependent on if the Qualcomm UFS PHY was ever
(partially) probed.
If the specific regulator should be always on in a particular device,
mark it so by specifying "regulator-always-on" in the regulator node.
Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
When regulator_get() tries to resolve a regulator supply but fail to
find a matching property in DeviceTree it returns a dummy regulator, if
a matching supply is specified but unavailable the regulator core will
return an error.
Based on this we should not ignore errors upon failing to acquire the
optional "vddp-ref-clk" supply.
Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Upon failing to acquire regulator supplies the qcom-ufs driver calls
kfree() on the devm allocated memory used to store the name of the
regulator, leading to devres corruption.
Rather than switching to using the appropriate free function the patch
acknowledge the fact that "name" is always a constant string and we
don't actually need to create a local copy of it, but rather just
reference the constant string.
Fixes: add78fc057 ("phy: qcom-ufs: Use devm sibling of kstrdup for regulator names")
Cc: stable@vger.kernel.org
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The high-speed phy on qcom SoCs is controlled via the ULPI
viewport.
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: <devicetree@vger.kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The HSIC USB controller on qcom SoCs has an integrated all
digital phy controlled via the ULPI viewport.
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Declare phy_ops structures as const as they are only passed as an
argument to the function devm_phy_create. This argument is of type const
struct phy_ops *, so phy_ops structures having this property can be
declared as const.
Done using Coccinelle:
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch replaces the deprecated extcon API as following:
- extcon_set_cable_state_() -> extcon_set_state_sync()
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch replaces the deprecated extcon API as following:
- extcon_set_cable_state_() -> extcon_set_state_sync()
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Allwinner V3s come with a USB PHY controller slightly different to other
SoCs, with only one PHY.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
According to the documentation, we should set the EXTCON_USB when
one SDP charger connector was reported.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This update includes the usual round of major driver updates (ncr5380,
lpfc, hisi_sas, megaraid_sas, ufs, ibmvscsis, mpt3sas). There's also
an assortment of minor fixes, mostly in error legs or other not very
user visible stuff. The major change is the pci_alloc_irq_vectors
replacement for the old pci_msix_.. calls; this effectively makes IRQ
mapping generic for the drivers and allows blk_mq to use the
information.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=sPXh
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This update includes the usual round of major driver updates (ncr5380,
lpfc, hisi_sas, megaraid_sas, ufs, ibmvscsis, mpt3sas).
There's also an assortment of minor fixes, mostly in error legs or
other not very user visible stuff. The major change is the
pci_alloc_irq_vectors replacement for the old pci_msix_.. calls; this
effectively makes IRQ mapping generic for the drivers and allows
blk_mq to use the information"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (256 commits)
scsi: qla4xxx: switch to pci_alloc_irq_vectors
scsi: hisi_sas: support deferred probe for v2 hw
scsi: megaraid_sas: switch to pci_alloc_irq_vectors
scsi: scsi_devinfo: remove synchronous ALUA for NETAPP devices
scsi: be2iscsi: set errno on error path
scsi: be2iscsi: set errno on error path
scsi: hpsa: fallback to use legacy REPORT PHYS command
scsi: scsi_dh_alua: Fix RCU annotations
scsi: hpsa: use %phN for short hex dumps
scsi: hisi_sas: fix free'ing in probe and remove
scsi: isci: switch to pci_alloc_irq_vectors
scsi: ipr: Fix runaway IRQs when falling back from MSI to LSI
scsi: dpt_i2o: double free on error path
scsi: cxlflash: Migrate scsi command pointer to AFU command
scsi: cxlflash: Migrate IOARRIN specific routines to function pointers
scsi: cxlflash: Cleanup queuecommand()
scsi: cxlflash: Cleanup send_tmf()
scsi: cxlflash: Remove AFU command lock
scsi: cxlflash: Wait for active AFU commands to timeout upon tear down
scsi: cxlflash: Remove private command pool
...
Merge contains:
*) Add new usb2 phy driver for Meson8b and GXBB
*) Remove phy drivers added for miphy365 and STiH415/6 (as support for
these SoCs are removed from the kernel)
*) Add a sysfs entry to facilitate usb role swap in rcar SoC
*) Add support for otg port in rk3399
*) misc fixes in various phy drivers and cleanups
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=jfKK
-----END PGP SIGNATURE-----
Merge tag 'phy-for-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 4.10
Merge contains:
*) Add new usb2 phy driver for Meson8b and GXBB
*) Remove phy drivers added for miphy365 and STiH415/6 (as support for
these SoCs are removed from the kernel)
*) Add a sysfs entry to facilitate usb role swap in rcar SoC
*) Add support for otg port in rk3399
*) misc fixes in various phy drivers and cleanups
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
When USB is disabled, we get a link error for this driver
because of the added OTG support
drivers/phy/phy-rockchip-inno-usb2.o: In function `rockchip_usb2phy_otg_sm_work':
phy-rockchip-inno-usb2.c:(.text.rockchip_usb2phy_otg_sm_work+0x1f4): undefined reference to `usb_otg_state_string'
drivers/phy/phy-rockchip-inno-usb2.o: In function `rockchip_usb2phy_probe':
phy-rockchip-inno-usb2.c:(.text.rockchip_usb2phy_probe+0x2c8): undefined reference to `of_usb_get_dr_mode_by_phy'
Other phy drivers select USB_COMMON for this, so let's do the same
here.
Fixes: 0c42fe48fd23 ("phy: rockchip-inno-usb2: support otg-port for rk3399")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The newly added OTG support has an obvious uninitialized variable
access that gcc warns about:
drivers/phy/phy-rockchip-inno-usb2.c: In function 'rockchip_chg_detect_work':
drivers/phy/phy-rockchip-inno-usb2.c:717:7: error: 'tmout' may be used uninitialized in this function [-Werror=maybe-uninitialized]
This replaces the use of the uninitialized variable with what
the value was in the previous USB_CHG_STATE_WAIT_FOR_DCD
state.
Fixes: 0c42fe48fd23 ("phy: rockchip-inno-usb2: support otg-port for rk3399")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Emit KOBJ_ONLINE/KOBJ_OFFLINE action uevent on VBUS status changes.
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The sunxi musb has a bug where sometimes it will generate a babble
error on device disconnect instead of a disconnect irq. When this
happens the musb-controller switches from host mode to device mode
(it clears MUSB_DEVCTL_SESSION and sets MUSB_DEVCTL_BDEVICE) and
gets stuck in this state.
Clearing this requires reporting Vbus low for 200 or more ms, but
on some devices Vbus is simply always high (host-only mode, no Vbus
control).
This commit modifies sun4i_usb_phy_set_mode so that it will force
end the current session when called with the current mode, before this
commit calling set_mode with the current mode was a nop since id_det
would stay the same resulting in the detect_work not doing anything.
This allows the sunxi-musb glue to use sun4i_usb_phy_set_mode to force
end the current session without changing the mode, to fixup the stuck
state after a babble error.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Remove unneeded variables when "0" can be returned.
Generated by: scripts/coccinelle/misc/returnvar.cocci
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR.
Generated by: scripts/coccinelle/api/ptr_ret.cocci
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
There is no need to access regmap of coupled phy to check its state - such
information is already in the phy device itself, so use it directly. This
let us to avoid possible access to registers of the device in the disabled
power domain if the coupled phy is already disabled.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch adds sysfs "role" for usb role swap. This parameter can be
read and write. If you use this file as the following, you can swap
the usb role.
For example:
1) Connect a usb cable using 2 Salvator-x boards
2) On A-Device (ID pin is low), you input the following command:
# echo peripheral > /sys/devices/platform/soc/ee080200.usb-phy/role
3) On B-Device (ID pin is high), you input the following command:
# echo host > /sys/devices/platform/soc/ee080200.usb-phy/role
Then, the A-device acts as a peripheral and the B-device acts as a host.
Please note that A-Device must input the following command if you
want the board to act as a host again. (even if you disconnect the usb
cable, since id state may be the same, the A-Device keeps to act as
peripheral.)
# echo host > /sys/devices/platform/soc/ee080200.usb-phy/role
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
If we configure the da8xx OTG phy in OTG mode, neither device or host
mode will work. That is because the PHY is not able to detect and notify
the driver that value of ID pin changed.
To work despite this hardware limitation, the da8xx glue implement a
workaround.
But to work, the workaround require the VBUS sense and the session end
comparator to enabled.
Enable them if the phy is configured in OTG mode.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
documentation.
This phy is only used on STiH415/6 based silicon, and support for
these SoC's is being removed from the kernel.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
documentation.
This phy is only used on STiH415/6 based silicon, and support for
these SoC's is being removed from the kernel.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
We found that the system crashed due to 480MHz output clock of
USB2 PHY was unstable after clock had been enabled by gpu module.
Theoretically, 1 millisecond is a critical value for 480MHz
output clock stable time, so we try to change the delay time
to 1.2 millisecond to avoid this issue.
And the commit ed907fb1d7c3 ("phy: rockchip-inno-usb2: correct
clk_ops callback") used prepare callbacks instead of enable
callbacks to support gate a clk if the operation may sleep. So
we can switch from delay to sleep functions.
Also fix a spelling error from "waitting" to "waiting".
Signed-off-by: William Wu <wulf@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Since we needs to delay ~1ms to wait for 480MHz output clock
of USB2 PHY to become stable after turn on it, the delay time
is pretty long for something that's supposed to be "atomic"
like a clk_enable(). Consider that clk_enable() will disable
interrupt and that a 1ms interrupt latency is not sensible.
The 480MHz output clock should be handled in prepare callbacks
which support gate a clk if the operation may sleep.
Signed-off-by: William Wu <wulf@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The rk3399 SoC USB2 PHY is comprised of one Host port and
one OTG port. And OTG port is for USB2.0 part of USB3.0 OTG
controller, as a part to construct a fully feature Type-C
subsystem.
With this patch, we can support OTG port with the following
functions:
- Support BC1.2 charger detect, and use extcon notifier to
send USB charger types to power driver.
- Support PHY suspend for power management.
- Support OTG Host only mode.
Signed-off-by: William Wu <wulf@rock-chips.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Both PHYs are sharing one reset line. With recent improvements to the
reset framework we can now also use reset_control_reset with shared
resets.
This allows us to drop some workarounds where the reset was only
specified for one PHY but not the other, to make sure that the reset it
only executed once (as the reset framework was not able to use
reset_control_reset with shared reset lines).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Fix the missing clk_disable_unprepare() before return from
phy_meson8b_usb2_power_on() in the error handling case.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This is a new driver for the USB PHY found in Meson8b and GXBB SoCs.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Now with musb driver implementing generic session bit based
PM, we need to have the USB PHYs behaving in a sane way for
platforms implementing PM.
Currently twl4030-usb enables PM in twl4030_phy_power_on()
and then disables it in twl4030_phy_power_off(). This will
block PM runtime for the SoC when no cable is connected.
Fix the issue by moving PM runtime autosuspend call to
happen where it gets called in twl4030_phy_power_on().
Note that this patch should not be backported to anything
before commit 467d5c9807 ("usb: musb: Implement session bit
based runtime PM for musb-core") as before that all the
glue layers implemented their own PM.
Fixes: 467d5c9807 ("usb: musb: Implement session bit based
runtime PM for musb-core")
Tested-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The common layer phy exit callback ufs_qcom_phy_exit()
calls phy_power_off() that has no meaning when phy_power_off()
callback is already registered with the phy provider and
the consumer makes use of the same.
Instead, add a no-op specific phy_exit() callback for now
to add the exit sequence at a later point.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add phy clock enable code to phy_power_on/off callbacks, and
remove explicit calls to enable these phy clocks from the
ufs-qcom hcd driver.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The phy init is meant to do phy initialization rather than
just getting the clock and regulator. Move these clock and
regulator get to probe(), to make room for actual phy
initialization sequence.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
remove() callback does a phy_power_off() only over the phy,
and nothing else now.
The phy_power_off() over the generic phy is called from the phy
consumer, and phy provider driver should not explicitly need to
call any phy ops.
So discard the remove callback for qcom-ufs phy platform drivers.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The tx_iface_clk and rx_iface_clk no longer exist with UFS Phy
present on msm8996. So skip obtaining these clocks using
compatible match.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a new compatible string for 14nm ufs phy present on msm8996
chipset. This phy is bit different from the legacy 14nm ufs phy
in terms of the clocks that are needed to be handled in the driver.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Different menthods pass around generic phy pointer to
extract device pointer. Instead, pass the device pointer
directly between function calls.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This helps us in avoiding any requirement for kfree() operation
to be called exclusively over the allocated string pointer.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
BUG_ON() are not preferred in the driver, plus the variable
on which BUG_ON is asserted is already checked in the code
before passing.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Allwinner SoC's PHY 0, when used as OTG controller, have no pmu part.
The code that poke some unknown bit of PMU for H3/A64 didn't check
the PHY, and will cause kernel oops when PHY 0 is used.
This patch will check whether the pmu is not NULL before poking.
Fixes: b3e0d141ca (phy: sun4i: add support for A64 usb phy)
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The deassert of phy_rst from exit callback is incorrect as when
doing phy_exit, we expect the phy_rst is on asserted state which was
done by power_off callback, but not deasserted state. Meanwhile when
disabling clk_pciephy_ref, the assert/deassert signal can't actually
take effect on the phy. So let's fix it anyway.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The ohci device name has changed in the board configuraion files,
hence, change the phy lookup table to match the new name.
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
twl4030_phy_power_on() initializes some bits which are required for
charging. As they are not set in twl4030_usb_runtime_resume()
a call to pm_runtime_get_sync() is not sufficient to enable charging.
This patch moves the initialization to twl4030_usb_runtime_resume()
so everything needed for charging is initialized upon
pm_runtime_get_sync().
That also gives improved possibilities to debug problems in that area
because the relevant parts can be checked separately. Charging can be
enabled without having the musb subsystem active.
As a side effect this hides some bugs in musb which causes
unbalanced calls to phy_power_off()/phy_power_on() so that
phy->power_count becomes -1.
The result is that e.g. the GTA04 phone (dm3730 + twl4030) works
finally as a usb gadget again and charging is working.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
setting twl->linkstat = MUSB_UNKNOWN upon error in musb_mailbox as
introduced in
commit 12b7db2bf8 ("usb: musb: Return error value from musb_mailbox")
causes twl4030_usb_irq() to not detect a state change form cable connected
to cable disconnected after such an error so that
pm_runtime_put_autosuspend() will not be called and the usage counter
gets unbalanced. Such errors happen e.g. if the omap2430 module is not
(yet) loaded during plug/unplug events.
This patch introduces a flag instead that indicates whether there is
information for the musb_mailbox pending and calls musb_mailbox() if
that flag is set.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The musb driver calls into this phy driver to disable/enable squelch
detection. This function was introduced in 24fe86a617 ("phy: sun4i-usb:
Add a sunxi specific function for setting squelch-detect"). This
function in turn calls sun4i_usb_phy_write, which uses a mutex to
guard the common access register. Unfortunately musb does this
in atomic context, which results in the following warning with lock
debugging enabled:
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:97
in_atomic(): 1, irqs_disabled(): 128, pid: 96, name: kworker/0:2
CPU: 0 PID: 96 Comm: kworker/0:2 Not tainted 4.8.0-rc4-00181-gd502f8ad1c3e #13
Hardware name: Allwinner sun8i Family
Workqueue: events musb_deassert_reset
[<c010bc01>] (unwind_backtrace) from [<c0109237>] (show_stack+0xb/0xc)
[<c0109237>] (show_stack) from [<c02a669b>] (dump_stack+0x67/0x74)
[<c02a669b>] (dump_stack) from [<c05d68c9>] (mutex_lock+0x15/0x2c)
[<c05d68c9>] (mutex_lock) from [<c02c3589>] (sun4i_usb_phy_write+0x39/0xec)
[<c02c3589>] (sun4i_usb_phy_write) from [<c03e6327>] (musb_port_reset+0xfb/0x184)
[<c03e6327>] (musb_port_reset) from [<c03e4917>] (musb_deassert_reset+0x1f/0x2c)
[<c03e4917>] (musb_deassert_reset) from [<c012ecb5>] (process_one_work+0x129/0x2b8)
[<c012ecb5>] (process_one_work) from [<c012f5e3>] (worker_thread+0xf3/0x424)
[<c012f5e3>] (worker_thread) from [<c0132dbd>] (kthread+0xa1/0xb8)
[<c0132dbd>] (kthread) from [<c0105f31>] (ret_from_fork+0x11/0x20)
Since the register access is mmio, we can use a spinlock to guard this
specific access, rather than the mutex that guards the entire phy.
Fixes: ba4bdc9e1d ("PHY: sunxi: Add driver for sunxi usb phy")
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
It is a hardware bug in RK3288, the only way to solve it is to
reset the phy.
Signed-off-by: Randy Li <ayaka@soulik.info>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The only use for this is for solving a hardware design problem in
usb of Rockchip RK3288.
Signed-off-by: Randy Li <ayaka@soulik.info>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Warn when external vbus is detected when we're trying to enable our
own vbus.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Together with some musb sunxi glue changes this allows run-time dr_mode
switching support via the "mode" musb sysfs attribute.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
If we cannot get dr_mode or no id gpio is specified simply assume
peripheral mode, as this is always safe.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The phy-sun4i-usb code supports forced ending a session on systems
which lack Vbus detection, to allow switching between host and peripheral
mode on such systems.
Role switching via the musb driver "mode" sysfs attribute requires force
ending the session too. This commit refactors the code to allow other
parts of the phy-sun4i-usb code to request a forced session end.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
We're using bool as true/false type in most places in phy-sun4i-usb.c
for consistency fixup the remaining uses of ints which are ever only
0 or 1 to be bools too.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Adds pm_runtime support for rockchip Type-C, so that power domain is
enabled only when there is a transaction going on to help save power.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The driver now calls of_usb_get_dr_mode_by_phy, which is part of the
USB core layer, and it fails to build when that is not provided:
drivers/phy/phy-sun4i-usb.o: In function `sun4i_usb_phy_probe':
phy-sun4i-usb.c:(.text.sun4i_usb_phy_probe+0x140): undefined reference to `of_usb_get_dr_mode_by_phy'
We already have a couple of other PHY drivers with a dependency
on USB_SUPPORT, so that seems to be the easiest fix here.
An alternative would be to adjust the #ifdef in include/linux/usb/of.h
to also check for CONFIG_USB_SUPPORT.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Fixes: b33ecca87d ("phy-sun4i-usb: Add support for peripheral-only mode")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add a PHY provider driver for the rk3399 SoC Type-c PHY. The USB
Type-C PHY is designed to support the USB3 and DP applications.
The USB3 operates in SuperSpeed mode and the DP can operate at RBR,
HBR and HBR2 data rates. This driver create 2 PHY devices separately
for USB3 and DisplyPort, and registers them under the child node.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Tested-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The syscon device in board config/device tree has been renamed.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
On kernel builds without COMMON_CLK, the newly added rockchip-inno-usb2
driver fails to build:
drivers/phy/phy-rockchip-inno-usb2.c:124:16: error: field 'clk480m_hw'
has incomplete type
struct clk_hw clk480m_hw;
In file included from include/linux/clk.h:16:0
from drivers/phy/phy-rockchip-inno-usb2.c:17:
include/linux/kernel.h:831:48: error: initialization from incompatible
pointer type [-Werror=incompatible-pointer-types]
const typeof( ((type *)0)->member ) *__mptr = (ptr); \
... ...
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Relying on PM-ops for shutting down PHY clocks was a
bad idea since the users (e.g. USB DWC3) might not
have been suspended by then.
Get rid of all PM-ops. It is the sole responsibility
of the PHY user to properly turn OFF and de-initialize
the PHY as part of its suspend routine.
Enable/disable PHY clock as part of ->init()/->exit()
call respectively. With this phy_init() and phy_exit()
can be called by PHY user during suspend/resume.
This is similar to what is done for ti-pipe3 driver.
See 31c8954efb1b ("phy: ti-pipe3: fix suspend")
The pm_runtime_enable() call in omap_usb2_probe()
is still required because without it, phy_create()
will not enable runtime PM on the phy device it
creates and phy_init() will not call
pm_runtime_get_sync().
Without pm_runtime_get_sync(), ocp2scp hwmod will
_not_ enable the IP and, thus, we will have abort
exceptions.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This driver can support for r8a7796 SoC. So, this patch adds it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add missing .owner field in ns2_pci_phy_ops, which is used for refcounting.
While at it, also makes ns2_pci_phy_ops const as it's never get modified.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-and-tested-by: Jon Mason <jon.mason@broadcom.com>
Reviewed-by: Pramod Kumar <pramodku@broadcom.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
By setting phy_set_drvdata(phy, mdiodev), struct ns2_pci_phy can be
removed.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-and-tested-by: Jon Mason <jon.mason@broadcom.com>
Reviewed-by: Pramod Kumar <pramodku@broadcom.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
We get 1 warning when building kernel with W=1:
drivers/phy/tegra/xusb.c:104:5: warning: no previous prototype for 'tegra_xusb_lane_lookup_function' [-Wmissing-prototypes]
In fact, this function is only used in the file in which it is
declared and don't need a declaration, but can be made static.
So this patch marks it 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
We get 5 warnings when building kernel with W=1:
drivers/phy/tegra/xusb.c:948:27: warning: no previous prototype for 'tegra_xusb_padctl_get' [-Wmissing-prototypes]
drivers/phy/tegra/xusb.c:981:6: warning: no previous prototype for 'tegra_xusb_padctl_put' [-Wmissing-prototypes]
drivers/phy/tegra/xusb.c:988:5: warning: no previous prototype for 'tegra_xusb_padctl_usb3_save_context' [-Wmissing-prototypes]
drivers/phy/tegra/xusb.c:998:5: warning: no previous prototype for 'tegra_xusb_padctl_hsic_set_idle' [-Wmissing-prototypes]
drivers/phy/tegra/xusb.c:1008:5: warning: no previous prototype for 'tegra_xusb_padctl_usb3_set_lfps_detect' [-Wmissing-prototypes]
In fact, these functions are declared in linux/phy/tegra/xusb.h,
so this patch adds missing header dependencies.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch to add a generic PHY driver for rockchip PCIe PHY.
Access the PHY via registers provided by GRF (general register
files) module.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The newer SoCs (rk3366, rk3399) take a different usb-phy IP block
than rk3288 and before, and most of phy-related registers are also
different from the past, so a new phy driver is required necessarily.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Suggested-by: Heiko Stuebner <heiko@sntech.de>
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Suggested-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Use of_property_read_bool to check for the existence of a property.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e1,e2,x;
@@
- if (of_get_property(e1,e2,NULL))
- x = true;
- else
- x = false;
+ x = of_property_read_bool(e1,e2);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Northstar is a family of SoCs used in home routers. They have USB 2.0
and 3.0 controllers with PHYs that need to be properly initialized.
This driver provides PHY init support in a generic way and can be bound
with XHCI controller driver.
There aren't any public datasheets from Broadcom so we can't have nice
defines for all used bits. It means we just follow Broadcom's
initialization procedure using their magic values. We were quite lucky
actually that Broadcom put some comments in their SDK reference code
explaining what given writes are responsible for.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
There's something unknown in the pmu part that shared with H3.
It's renamed as PMU_UNK1 from PMU_UNK_H3.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
William wu