Basically the io watchdog is only useful for those quirk HCDs. For most
good ones, it only brings unnecessary wakeups. At least, I know the
Intel EHCI HCDs should turn off the flag.
Signed-off-by: Alek Du <alek.du@intel.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds to the usbsevseg driver:
- suspend/resume support
- reset_resume support
- autosuspend using the display's power state to determine idleness
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Harrison Metzger <harrisonmetz@gmail.com>
usb: full runtime PM support for idmouse driver
- add suspend/resume support
- add reset_resume support
- add support for autosuspend
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Tested-by: Andreas Deresch <aderesch@fs.tum.de>
list_entry, which is an alias for container_of, cannot return NULL, as
there is no way to add a NULL value to a doubly linked list.
A simplified version of the semantic match that findds this problem is as
follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r@
expression x,E;
statement S1,S2;
position p,p1;
@@
*x = list_entry@p(...)
... when != x = E
*if@p1 (x == NULL) S1 else S2
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
poll() should test for a disconnection of the device.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
poll needs to return an error if a device is disconnected
- make poll check for device's presence
- wake all waiters in disconnect
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
a class driver should have suspend/resume. This makes sure we
don't see a virtual disconnect unnecessarily.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usbtmc will happily complete read/write requests even after disconnect
has returned. The fix is to introduce a flag.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are some unused variables in serial_do_down. Remove them.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this adds autosupport usable even in an always online mode.
- enables remote wakeup on open
- autoresume for sending
- timeout based autosuspend if nothing is sent or recieved
- autosuspend without remote wakeup support on open/close
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Tested-off-by: Zhao Ming <zhao.ming9@zte.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds very basic otg_transceiver support, with vbus_session
and vbus_draw callbacks.
Now VBUS sensing can be handled by an external driver which registers
the otg_transceiver interface. It also allows gadget drivers to configure
the current drawn from VBUS. The UDC driver just passes their requests
along to the transceiver driver.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1261) reduces the amount of detailed URB information
logged by usbfs when the usbfs_snoop parameter is enabled.
Currently we don't display the final status value for a completed URB.
But we do display the entire data buffer twice: both before submission
and after completion. The after-completion display doesn't limit
itself to the actual_length value. But since usbmon is readily
available in virtually all distributions, there's no reason for usbfs
to print out any buffer contents at all!
So this patch restricts the information to: userspace buffer pointer,
endpoint number, type, and direction, length or actual_length, and
timeout value or status. Now everything fits neatly into a single
line.
Along with those changes, the patch also fixes the snoop output for
the REAPURBNDELAY and REAPURBNDELAY32 ioctls. The current version
omits the 'N' from the names.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1260) changes the pm_usage_cnt field in struct
usb_interface from an int to an atomic_t. This is so that drivers can
invoke the usb_autopm_get_interface_async() and
usb_autopm_put_interface_async() routines without locking and without
fear of corrupting the pm_usage_cnt value.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1258) implements a feature that users have been asking
for: It gives programs the ability to "claim" a port on a hub, via a
new usbfs ioctl. A device plugged into a "claimed" port will not be
touched by the kernel beyond the immediate necessities of
initialization and enumeration.
In particular, when a device is plugged into a "claimed" port, the
kernel will not select and install a configuration. And when a config
is installed by usbfs or sysfs, the kernel will not probe any drivers
for any of the interfaces. (However the kernel will fetch various
string descriptors during enumeration. One could argue that this
isn't really necessary, but the strings are exported in sysfs.)
The patch does not guarantee exclusive access to these devices; it is
still possible for more than one program to open the device file
concurrently. Programs are responsible for coordinating access among
themselves.
A demonstration program showing how to use the new interface can be
found in an attachment to
http://marc.info/?l=linux-usb&m=124345857431452&w=2
The patch also makes a small simplification to the hub driver,
replacing a bunch of more-or-less useless variants of "out of memory"
with a single message.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb_hcd_endpoint_reset() may be called in atomic context and must not
sleep. So make whci-hcd's endpoint_reset() asynchronous. URBs
submitted while the reset is in progress will be queued (on the std
list) and transfers will resume once the reset is complete.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add ehci support for w90p910 platform.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Those functions are used only used to fill the set/get members of
usb_audio_control. It doesn't make much sense to inline them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
linux/usb/audio.h is a public header file that includes definitions
exported to userspace. To avoid namespace clashes, prefix all macro
definitions with UAC_. Existing macros and structures prefixed with
USB_AC_ and USB_AS_ are renamed for consistency.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB_SUBCLASS_VENDOR_SPEC is common to several USB classes and as such belongs
to usb/ch9.h.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
And use the new definitions in the USB Audio Class gadget driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fix permits the "new" usbmon to access usb-storage's data buffer
without DMA remapping tricks. It should be compatible with PIO controllers
and not add any new crashes. Note that from now on PIO controllers and
usbmon are uniform in their access pattern and if one crashes then
the other will too. Hopefuly neither does.
As a side effect, we get rid for #ifdefs, which were a little ugly.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes crashes when usbmon attempts to access GART aperture.
The old code attempted to take a bus address and convert it into a
virtual address, which clearly was impossible on systems with actual
IOMMUs. Let us not persist in this foolishness, and use transfer_buffer
in all cases instead.
I think downsides are negligible. The ones I see are:
- A driver may pass an address of one buffer down as transfer_buffer,
and entirely different entity mapped for DMA, resulting in misleading
output of usbmon. Note, however, that PIO based controllers would
do transfer the same data that usbmon sees here.
- Out of tree drivers may crash usbmon if they store garbage in
transfer_buffer. I inspected the in-tree drivers, and clarified
the documentation in comments.
- Drivers that use get_user_pages will not be possible to monitor.
I only found one driver with this problem (drivers/staging/rspiusb).
- Same happens with with usb_storage transferring from highmem, but
it works fine on 64-bit systems, so I think it's not a concern.
At least we don't crash anymore.
Why didn't we do this in 2.6.10? That's because back in those days
it was popular not to fill in transfer_buffer, so almost all
traffic would be invisible (e.g. all of HID was like that).
But now, the tree is almost 100% PIO friendly, so we can do the
right thing at last.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I think this sentence was confusing regarding the possible size
of the data area.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These statements seem to be unnecessary. No idea why, but I built all
possible configurations and everything gets built just as before.
It's an old patch that popped from discussion with Paul in November 2008.
Obviously not a very high priority but better late than never.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch falls out of my work to fix usbmon so it uses virtual addresses.
It is not necessary, the "new" usbmon should work just fine with sisusbvga.
However, it seems ridiculous that anyone would use uncached memory to
transfer bulk data. Dropping the unnecessary use of usb_buffer_alloc
should be beneficial here, in case anyone ever uses the dongle on
anything beyond x86.
I had no success in raising the author of the driver by e-mail, so
the patch is not actually tested.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
vfree() does it's own NULL checking,so no need for check before
calling it.
Signed-off-by: Figo.zhang <figo1802@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When there's a descriptor after the SuperSpeed endpoint companion
descriptor, the previous code would have skipped over twice the length it
was supposed to. This code fixes crashes seen with UASP devices (which
have a UASP descriptor after the SS endpoint companion descriptor).
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Interrupt transfers are submitted to the xHCI hardware using the same TRB
type as bulk transfers. Re-use the bulk transfer enqueueing code to
enqueue interrupt transfers.
Interrupt transfers are a bit different than bulk transfers. When the
interrupt endpoint is to be serviced, the xHC will consume (at most) one
TD. A TD (comprised of sg list entries) can take several service
intervals to transmit. The important thing for device drivers to note is
that if they use the scatter gather interface to submit interrupt
requests, they will not get data sent from two different scatter gather
lists in the same service interval.
For now, the xHCI driver will use the service interval from the endpoint's
descriptor (bInterval). Drivers will need a hook to poll at a more
frequent interval. Set urb->interval to the interval that the xHCI
hardware will use.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The xHCI hardware reports the number of bytes untransferred for a given
transfer buffer. If the hardware reports a bytes untransferred value
greater than the submitted buffer size, we want to play it safe and say no
data was transferred. If the driver considers a short packet to be an
error, remember to set -EREMOTEIO.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make sure that the driver that submitted the URB considers a short packet
an error before setting -EREMOTEIO during a short control transfer.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make sure that the amount of data the xHC says was transmitted is less
than or equal to the size of the requested transfer buffer. Before, if
the host controller erroneously reported that the number of bytes
untransferred was bigger than the buffer in the URB, urb->actual_length
could be set to a very large size.
Make sure urb->actual_length <= urb->transfer_buffer_length.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On a successful transfer, urb->td is freed before the URB is ready to be
given back to the driver. Don't touch urb->td after it's freed. This bug
would have only shown up when xHCI debugging was turned on, and the freed
memory was quickly reused for something else.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The 0.95 xHCI spec says that non-control endpoints will be halted if a
babble is detected on a transfer. The 0.96 xHCI spec says all types of
endpoints will be halted when a babble is detected. Some hardware that
claims to be 0.95 compliant halts the control endpoint anyway.
When a babble is detected on a control endpoint, check the hardware's
output endpoint context to see if the endpoint is marked as halted. If
the control endpoint is halted, a reset endpoint command must be issued
and the transfer ring dequeue pointer needs to be moved past the stopped
transfer. Basically, we treat it as if the control endpoint had stalled.
Handle bulk babbling endpoints as if we got a completion event with a
stall completion code.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use trb_comp_code instead of getting the completion code from the transfer
event every time.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This Fresco Logic xHCI host controller chip revision puts bad data into
the output endpoint context after a Reset Endpoint command. It needs a
Configure Endpoint command (instead of a Set TR Dequeue Pointer command)
after the reset endpoint command.
Set up the input context before issuing the Reset Endpoint command so we
don't copy bad data from the output endpoint context. The HW also can't
handle two commands queued at once, so submit the TRB for the Configure
Endpoint command in the event handler for the Reset Endpoint command.
Devices that stall on control endpoints before a configuration is selected
will not work under this Fresco Logic xHCI host controller revision.
This patch is for prototype hardware that will be given to other companies
for evaluation purposes only, and should not reach consumer hands. Fresco
Logic's next chip rev should have this bug fixed.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a control endpoint stalls, the next control transfer will clear the
stall. The USB core doesn't call down to the host controller driver's
endpoint_reset() method when control endpoints stall, so the xHCI driver
has to do all its stall handling for internal state in its interrupt handler.
When the host stalls on a control endpoint, it may stop on the data phase
or status phase of the control transfer. Like other stalled endpoints,
the xHCI driver needs to queue a Reset Endpoint command and move the
hardware's control endpoint ring dequeue pointer past the failed control
transfer (with a Set TR Dequeue Pointer or a Configure Endpoint command).
Since the USB core doesn't call usb_hcd_reset_endpoint() for control
endpoints, we need to do this in interrupt context when we get notified of
the stalled transfer. URBs may be queued to the hardware before these two
commands complete. The endpoint queue will be restarted once both
commands complete.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Full speed devices have varying max packet sizes (8, 16, 32, or 64) for
endpoint 0. The xHCI hardware needs to know the real max packet size
that the USB core discovers after it fetches the first 8 bytes of the
device descriptor.
In order to fix this without adding a new hook to host controller drivers,
the xHCI driver looks for an updated max packet size for control
endpoints. If it finds an updated size, it issues an evaluate context
command and waits for that command to finish. This should only happen in
the initialization and device descriptor fetching steps in the khubd
thread, so blocking should be fine.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Set the max packet size for the default control endpoint on high speed
devices to be 64 bytes. High speed devices always have a max packet size
of 64 bytes. There's no use setting it to eight for the initial 8 byte
descriptor fetch and then issuing (and waiting for) an evaluate context
command to update it to 64 bytes for the subsequent control transfers.
The USB core guesses that the max packet size on a full speed control
endpoint is 64 bytes, and then updates it after the first 8-byte
descriptor fetch. Change the initial setup for the xHCI internal
representation of the full speed device to have a 64 byte max packet size.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Refactor out the code issue, wait for, and parse the event completion code
for a configure endpoint command. Modify it to support the evaluate
context command, which has a very similar submission process. Add
functions to copy parts of the output context into the input context
(which will be used in the evaluate context command).
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use the virtual address of the memory hardware uses, not the address for
the container of that memory.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Different sections of the xHCI 0.95 specification had opposing
requirements for the chain bit in a link transaction request buffer (TRB).
The chain bit is used to designate that adjacent TRBs are all part of the
same scatter gather list that should be sent to the device. Link TRBs can
be in the middle, or at the beginning or end of these chained TRBs.
Sections 4.11.5.1 and 6.4.4.1 both stated the link TRB "shall have the
chain bit set to 1", meaning it is always chained to the next TRB.
However, section 4.6.9 on the stop endpoint command has specific cases for
what the hardware must do for a link TRB with the chain bit set to 0. The
0.96 specification errata later cleared up this issue by fixing the
4.11.5.1 and 6.4.4.1 sections to state that a link TRB can have the chain
bit set to 1 or 0.
The problem is that the xHCI cancellation code depends on the chain bit of
the link TRB being cleared when it's at the end of a TD, and some 0.95
xHCI hardware simply stops processing the ring when it encounters a link
TRB with the chain bit cleared.
Allow users who are testing 0.95 xHCI prototypes to set a module parameter
(link_quirk) to turn on this link TRB work around. Cancellation may not
work if the ring is stopped exactly on a link TRB with chain bit set, but
cancellation should be a relatively uncommon case.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Detect the UART on interface1 and blacklist interface0 (as that is the
JTAG port).
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
SL811 Device detected after removal used to be working in linux-2.6.22
but then broke somewhere between 2.6.22 and 2.6.28. Current
hub_port_connect_change() in drivers/usb/core/hub.c won't call
usb_disconnect() in case the SL811 driver sets portstatus
USB_PORT_FEAT_CONNECTION upon removal.
AFAIK the SL811 has only a combined Device Insert/Remove
detection bit, therefore use a count to distinguish insert or remove.
Signed-Off-By: Michael Hennerich <hennerich@blackfin.uclinux.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some devices from the OpenDCC project are missing in the list
of the FTDI PIDs. These PIDs are listed at
http://www.opendcc.de/elektronik/usb/opendcc_usb.html
(Sorry for the german only page.)
This patch adds the three missing devices.
Signed-off-by: Rainer Keller <mail@rainerkeller.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
cdc-acm needs to set a flag during open to tell the
tty layer that the device is initialized
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Paul Martin <pm@debian.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
support for O_NONBLOCK in read and write path
by simply not waiting for data in read or availability
of the write urb in write but returning -EAGAIN
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Tested-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add ID for Telit UC-864G GPS/UMTS/WCDMA modem and GPS receiver
to the option driver.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A few days ago i got the latest ZTE EVDO modem shown at:
http://img.alibaba.com/photo/240150115/ZTE_AC2726_EVDO_USB_Data_Modem.jpg
It seems that the latest kernel does not have support for it.
I wrote a small patch for the options.c module to add the relevant usb
ids to it.
From: Huzaifa Sidhpurwala <sidhpurwala.huzaifa@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I'd like to present my small patch enabling to use Sanwa PC5000
mulitimeter with linux.
Signed-off-by: Pawel Ludwikow <pludwiko@rab.ict.pwr.wroc.pl>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>