Command structure and event flow doesn't seem to
be any different compared to existing
implementation for other firmware branches.
This patch effectively adds in-driver support for
spectral scanning on QCA61x4 and QCA9377.
Tested QCA9377 w/ WLAN.TF.1.0-00267-1.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Neither of these did the right thing:
- get_tsf just returned 0
- set_tsf assumed a simple offset was applied against
get_tsf(), which works, except in the case of
calculating TSF from rx_mactime (actual TSF).
Just remove them for now. We can reimplement set_tsf in
terms of TSF increment/decrement in the future if get_tsf
is ever supported by FW.
Signed-off-by: Thomas Pedersen <twp@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Current set_tsf is implemented in terms of TSF_INCREMENT
only. Instead support new WMI command TSF_DECREMENT and
export these through offset_tsf. Advantage is we get
more accurate TSF adjustments, and don't calculate wrong
offset in case absolute TSF was calculated from rx_mactime
(actual TSF).
The new WMI command is available in firmware
10.4-3.2.1-00033 for QCA4019 chips. Old drivers on new
firmware or vice versa shouldn't be a problem since
get/set tsf logic was already broken.
Signed-off-by: Thomas Pedersen <twp@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Indicate hardware (or firmware) supports that CQM packet-loss report
will be generated based on station kickout algorithm. As of now mac80211
tracks connection loss by missing msdu counts (50) whereas ath10k
firmware tracks them by missing ppdus (+ BAR tries). While firmware is
trying to adapt its rate table, mac80211 might send out low_ack event to
hostapd. This is causing frequent connect and disconnect iteration under
noisy environment or when station is roaming around.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The word "background" contains 10 characters so the third argument of
strncmp() need to be 10 in order to match this prefix correctly.
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Fixes: 855aed1220 ("ath10k: add spectral scan feature")
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Remove extraneous error message in 'ath10k_htt_tx_alloc_cont_frag_desc'
as the caller 'ath10k_htt_tx_alloc' already dumps a proper error
message
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
cleanup 'ath10k_htt_tx_alloc' by introducing the API's
'ath10k_htt_tx_alloc/free_{cont_txbuf, txdone_fifo} and
re-use them whereever needed
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This partially reverts 'commit 2cdce425aa
("ath10k: Fix broken NULL func data frame status for 10.4")'
Unfortunately this breaks sending NULL func and the existing
issue of obtaining proper tx status for NULL function will be
fixed. Also update the comments for feature flag added to be
useless and not working
Fixes: 2cdce425aa "ath10k: Fix broken NULL func data frame status for
10.4"
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
arvifs list is traversed within data_lock spin_lock in tasklet
context to fill channel information from the corresponding vif.
This means any access to arvifs list for add/del operations
should also be protected with the same spin_lock to avoid the
race. Fix this by performing list add/del on arvfis within the
data_lock. This could fix kernel panic something like the below.
LR is at ath10k_htt_rx_pktlog_completion_handler+0x100/0xb6c [ath10k_core]
PC is at ath10k_htt_rx_pktlog_completion_handler+0x1c0/0xb6c [ath10k_core]
Internal error: Oops: 17 [#1] PREEMPT SMP ARM
[<bf4857f4>] (ath10k_htt_rx_pktlog_completion_handler+0x2f4/0xb6c [ath10k_core])
[<bf487540>] (ath10k_htt_txrx_compl_task+0x8b4/0x1188 [ath10k_core])
[<c00312d4>] (tasklet_action+0x8c/0xec)
[<c00309a8>] (__do_softirq+0xdc/0x208)
[<c0030d6c>] (irq_exit+0x84/0xe0)
[<c005db04>] (__handle_domain_irq+0x80/0xa0)
[<c00085c4>] (gic_handle_irq+0x38/0x5c)
[<c0009640>] (__irq_svc+0x40/0x74)
(gdb) list *(ath10k_htt_rx_pktlog_completion_handler+0x1c0)
0x136c0 is in ath10k_htt_rx_h_channel (drivers/net/wireless/ath/ath10k/htt_rx.c:769)
764 struct cfg80211_chan_def def;
765
766 lockdep_assert_held(&ar->data_lock);
767
768 list_for_each_entry(arvif, &ar->arvifs, list) {
769 if (arvif->vdev_id == vdev_id &&
770 ath10k_mac_vif_chan(arvif->vif, &def) == 0)
771 return def.chan;
772 }
773
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
'ath10k_htt_rx_h_unchain' needs to be called only if the return
value from 'ath10k_htt_rx_amsdu_pop' is 1('chained msdu's'), this
change makes it more explicit and avoids doing a skb_peek, fetching
rx descriptor pointer, checking rx msdu decap format for the case of
ret = 0 (unchained msdus). Found this change during code walk through,
not sure if this addresses any issue.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Unfortunately ath10k does not generally allow modifying the coverage class
with the stock firmware and Qualcomm has so far refused to implement this
feature so that it can be properly supported in ath10k. If we however know
the registers that need to be modified for proper operation with a higher
coverage class, then we can do these modifications from the driver.
This is a hack and might cause subtle problems but as it's not enabled by
default (only when user space changes the coverage class explicitly) it should
not cause new problems for existing setups. But still this should be considered
as an experimental feature and used with caution.
This patch implements the support for first generation cards (QCA9880, QCA9887
and so on) which are based on a core that is similar to ath9k. The registers
are modified in place and need to be re-written every time the firmware sets
them. To achieve this the register status is verified after certain WMI events
from the firmware.
The coverage class may not be modified temporarily right after the card
re-initializes the registers. This is for example the case during scanning.
Thanks to Sebastian Gottschall <s.gottschall@dd-wrt.com> for initially
working on a userspace support for this. This patch wouldn't have been
possible without this documentation.
Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fit.fraunhofer.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This overrides whatever regulatory the device
EEPROM contains and uses what the platform says
instead - in this implementation the ACPI driver.
In case the hint is not programmed or corrupted (0xffff)
the device falls back to the eeprom programmed settings.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
[kvalo@qca.qualcomm.com: remove ifdef, change error handling, change info messages to dbg]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
During offchannel scan, iw survey dump shows wrong values.
Fix this by assigning cycle counter wranarround type for
QCA9888 and QCA9884, they share same config with QCA4019.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch helps to get the TPC stats for 10.4 fw variants.
Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware is running watchdog timer for tracking copy engine ring index
and write index. Whenever both indices are stuck at same location for
given duration, watchdog will be trigger to assert target. While
updating copy engine destination ring write index, driver ensures that
write index will not be same as read index by finding delta between these
two indices (CE_RING_DELTA).
HTT target to host copy engine (CE5) is special case where ring buffers
will be reused and delta check is not applied while updating write index.
In rare scenario, whenever CE5 ring is full, both indices will be referring
same location and this is causing CE ring stuck issue as explained
above. This issue is originally reported on IPQ4019 during long hour stress
testing and during veriwave max clients testsuites. The same issue is
also observed in other chips as well. Fix this by ensuring that write
index is one less than read index which means that full ring is
available for receiving data.
Cc: stable@vger.kernel.org
Tested-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Ignore processing further in SWBA event scheduled for a vif, if mac80211
has marked the particular vif for stop beaconing and brought the vdev
down in 'ath10k_control_beaconing'. This should potentially avoid ath10k
warning/error messages while running continuous wifi down/up with max
number of vaps configured. Found this change during code walk through
and going through other beacon configuration related functions in ath10k
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix to return a negative error code from the error handling case
instead of 0, as done elsewhere in function ath10k_ahb_probe() or
ath10k_ahb_resource_init().
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The (1 << x) - 1 trick won't work when you
are trying to fill up all 64 bits, so add special
case for that.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[kvalo@qca.qualcomm.com: remove the sentence about moving limits]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
They are not necessarily named in an intuitive manner,
so at least add some comments to help the next person.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Chipset from QCA99X0 onwards (QCA99X0, QCA9984, QCA4019 & future)
rx_hdr_status is not padded to align in 4-byte boundary. Define a
new hw_params field to handle different alignment behaviour between
different hw. This patch fixes improper retrieval of rfc1042 header
with QCA4019. This patch along with "ath10k: Properly remove padding
from the start of rx payload" will fix traffic failure in ethernet
decap mode for QCA4019.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since reset_control_get() never returns NULL, we can use IS_ERR()
instead of IS_ERR_OR_NULL(). The return statements can be simpler
as well.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use the managed variant of reset_control_get() to simplify the
failure path and the .remove callback.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use the managed variant of clk_get() to simplify the failure path
and the .remove callback.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Correct some trivial comment typos.
Remove unnecessary parentheses in a long line.
Signed-off-by: Joe Perches <joe@perches.com>
[kvalo@qca.qualcomm.com: drop the change for return]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
hw_4addr_pad was added to handle different types of padding
in 4-address rx frame. But this padding is not very specific
to 4-address, it can happen even with three address + ethernet
decap mode. Since the padding information can be obtained
through Rx desc for QCA99X0 and newer chips, this hw_param
is not needed any more.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In QCA99X0 (QCA99X0, QCA9984, QCA9888 and QCA4019) family chips,
hw adds padding at the begining of the rx payload to make L3
header 4-byte aligned. In the chips doing this type of padding,
the number of bytes padded will be indicated through msdu_end:info1.
Define a hw_rx_desc_ops wrapper to retrieve the number of padded
bytes and use this while doing undecap. This should fix padding
related issues with ethernt decap format with QCA99X0, QCA9984,
QCA9888 and QCA4019 hw.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
[Rename operations to hw_ops for other purposes]
Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are slight differences in Rx hw descriptor information
among different chips. So far driver does not use those new
information for any functionalities, but there is one important
information which is available from QCA99X0 onwards to indicate
the number of bytes that hw padded at the begining of the rx
payload and this information is needed to undecap the rx
packet. Add an abstraction for Rx desc to make use of the
new desc information available. The callback that this patch
defines to retrieve the padding bytes will be used in follow-up
patch.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
[Rename operations to hw_ops for other purposes]
Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is to prepare for rx descriptor abstraction where we'll
be dereferencing ath10k_hw_params member in hw.h. Moreover
hw.h looks more suitable to house ath10k_hw_params definition
than core.h
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Helps to know the sta pointer.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[kvalo@qca.qualcomm.com: add %pK and remove the colon]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
IFTYPE_MESH_POINT need to rely on these for accurate path
selection metrics. Other modes will probably also find
them useful. Enabling peer stats has the side effect of
reducing max number of STAs from 128 to 118. There should
be negligible performance impact.
If users really need 128 STAs and don't mind losing out on
peer stats, they can still disable them:
echo 0 > debugfs/ieee80211/phyn/ath10k/peer_stats
Signed-off-by: Thomas Pedersen <twp@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Trival fix to remove unused variable ar_pci in ath10k_pci_tx_pipe_cleanup
when building with W=1:
drivers/net/wireless/ath/ath10k/pci.c:1696:21: warning: variable
'ar_pci' set but not used [-Wunused-but-set-variable]
Signed-off-by: Chaehyun Lim <chaehyun.lim@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
caldata is not being free'd on the error exit path, causing
a memory leak and data definitely should not be freed. Free
caldata instead of data.
Thanks to Kalle Valo for spotting that data should not be
free'd.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit 3c97f5de1f ("ath10k: implement NAPI support") conflicts with
ath-current. To avoid any merge problems merge ath-current to ath-next already now.
Conflicts:
drivers/net/wireless/ath/ath10k/htt_rx.c
When user requests for survey dump data, driver is providing wrong survey
information. This information we sent is the survey data that we have
collected during previous user request.
This issue occurs because we request survey dump for wrong channel. With
this change, we correctly display the correct and current survey
information to userspace.
Fixes: fa7937e3d5 ("ath10k: update bss channel survey information")
Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The error assigned does not seems to be used anywhere,
fixes nothing just a small cleanup
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
commit 7a0adc83f3 ("ath10k: improve tx scheduling") is causing
severe throughput drop in multi client mode. This issue is originally
reported in veriwave setup with 50 clients with TCP downlink traffic.
While increasing number of clients, the average throughput drops
gradually. With 50 clients, the combined peak throughput is decreased
to 98 Mbps whereas reverting given commit restored it to 550 Mbps.
Processing txqs for every tx completion is causing overhead. Ideally for
management frame tx completion, pending txqs processing can be avoided.
The change partly reverts the commit "ath10k: improve tx scheduling".
Processing pending txqs after all skbs tx completion will yeild enough
room to burst tx frames.
Fixes: 7a0adc83f3 ("ath10k: improve tx scheduling")
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add NAPI support for rx and tx completion. NAPI poll is scheduled
from interrupt handler. The design is as below
- on interrupt
- schedule napi and mask interrupts
- on poll
- process all pipes (no actual Tx/Rx)
- process Rx within budget
- if quota exceeds budget reschedule napi poll by returning budget
- process Tx completions and update budget if necessary
- process Tx fetch indications (pull-push)
- push any other pending Tx (if possible)
- before resched or napi completion replenish htt rx ring buffer
- if work done < budget, complete napi poll and unmask interrupts
This change also get rid of two tasklets (intr_tq and txrx_compl_task).
Measured peak throughput with NAPI on IPQ4019 platform in controlled
environment. No noticeable reduction in throughput is seen and also
observed improvements in CPU usage. Approx. 15% CPU usage got reduced
in UDP uplink case.
DL: AP DUT Tx
UL: AP DUT Rx
IPQ4019 (avg. cpu usage %)
========
TOT +NAPI
=========== =============
TCP DL 644 Mbps (42%) 645 Mbps (36%)
TCP UL 673 Mbps (30%) 675 Mbps (26%)
UDP DL 682 Mbps (49%) 680 Mbps (49%)
UDP UL 720 Mbps (28%) 717 Mbps (11%)
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Trivial fix to spelling mistake in ath10k_warn message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Older firmware with HTT delivers incorrect tx status for null func
frames to driver, but this fixed in 10.2 and 10.4 firmware versions.
Also this workaround results in reporting of incorrect null func status
for 10.4. Fix this is by introducing a firmware feature flag for 10.4
so that this workaround is skipped and proper tx status for null func
frames are reported
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit 97f2645f35 ("tree-wide: replace config_enabled() with
IS_ENABLED()") mostly did away with config_enabled().
This is one of the postponed TODO items as config_enabled() is used
for a tristate option here. Theoretically, config_enabled() is
equivalent to IS_BUILTIN(), but I guess IS_REACHABLE() is the best
fit for this case because both CONFIG_HWMON and CONFIG_ATH10K are
tristate.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For 10.4 fw versions, dbglog module id has been extended from u32
to u64, hence this patch fixes the same in the ath10k driver side.
This patch doesn't break the older 10.4 releases. The FW change
is already present in the older FWs.
Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There is only one waiter for the completion, therefore there
is no need to use complete_all(). Let's make that clear by
using complete() instead of complete_all().
The usage pattern of the completion is:
waiter context waker context
scan.started
------------
ath10k_start_scan()
lockdep_assert_held(conf_mutex)
auth10k_wmi_start_scan()
wait_for_completion_timeout(scan.started)
ath10k_wmi_event_scan_start_failed()
complete(scan.started)
ath10k_wmi_event_scan_started()
complete(scan.started)
scan.completed
--------------
ath10k_scan_stop()
lockdep_assert_held(conf_mutex)
ath10k_wmi_stop_scan()
wait_for_completion_timeout(scan.completed)
__ath10k_scan_finish()
complete(scan.completed)
scan.on_channel
---------------
ath10k_remain_on_channel()
mutex_lock(conf_mutex)
ath10k_start_scan()
wait_for_completion_timeout(scan.on_channel)
ath10k_wmi_event_scan_foreign_chan()
complete(scan.on_channel)
offchan_tx_completed
--------------------
ath10k_offchan_tx_work()
mutex_lock(conf_mutex)
reinit_completion(offchan_tx_completed)
wait_for_completion_timeout(offchan_tx_completed)
ath10k_report_offchain_tx()
complete(offchan_tx_completed)
install_key_done
----------------
ath10k_install_key()
lockep_assert_held(conf_mutex)
reinit_completion(install_key_done)
wait_for_completion_timeout(install_key_done)
ath10k_htt_t2h_msg_handler()
complete(install_key_done)
vdev_setup_done
---------------
ath10k_monitor_vdev_start()
lockdep_assert_held(conf_mutex)
reinit_completion(vdev_setup_done)
ath10k_vdev_setup_sync()
wait_for_completion_timeout(vdev_setup_done)
ath10k_wmi_event_vdev_start_resp()
complete(vdev_setup_done)
ath10k_monitor_vdev_stop()
lockdep_assert_held(conf_mutex)
reinit_completion(vdev_setup_done()
ath10k_vdev_setup_sync()
wait_for_completion_timeout(vdev_setup_done)
ath10k_wmi_event_vdev_stopped()
complete(vdev_setup_done)
thermal.wmi_sync
----------------
ath10k_thermal_show_temp()
mutex_lock(conf_mutex)
reinit_completion(thermal.wmi_sync)
wait_for_completion_timeout(thermal.wmi_sync)
ath10k_thermal_event_temperature()
complete(thermal.wmi_sync)
bss_survey_done
---------------
ath10k_mac_update_bss_chan_survey
lockdep_assert_held(conf_mutex)
reinit_completion(bss_survey_done)
wait_for_completion_timeout(bss_survey_done)
ath10k_wmi_event_pdev_bss_chan_info()
complete(bss_survey_done)
All complete() calls happen while the conf_mutex is taken. That means
at max one waiter is possible.
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In the wake tx queue path, we are not checking if the frame to be sent
takes management path or not. For eg. QOS null func frame coming here will
take the management path. Since we are not incrementing the descriptor
counter (num_pending_mgmt_tx) w.r.t tx management, on tx completion it is
possible to see negative values.
When the above counter reaches a negative value, we will not be sending a
probe response out.
if (is_presp &&
ar->hw_params.max_probe_resp_desc_thres < htt->num_pending_mgmt_tx)
For IPQ4019, max_probe_resp_desc_thres (u32) is 24 is compared against
num_pending_mgmt_tx (int) and the above condtions comes true if the counter
is negative and we drop the probe response.
To avoid this, check on the wake tx queue path as well for the tx path of
the frame and increment the appropriate counters
Fixes: cac085524c "ath10k: move mgmt descriptor limit handle under mgmt_tx"
Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
txqs_lock is interfering with wake_tx_queue submitting more frames.
so queues don't get filled in and don't keep firmware/hardware busy
enough. This change helps to reduce the txqs_lock contention and
wake_tx_queue() blockage to being possible in txrx_unref().
To reduce turn around time of wake_tx_queue ops and to maintain fairness
among all txqs, the callback is updated to push first txq alone from
pending list for every wake_tx_queue call. Remaining txqs will be
processed later upon tx completion.
Below improvements are observed in push-only mode and validated on
IPQ4019 platform. With this change, in AP mode ~10Mbps increase is
observed in downlink (AP -> STA) traffic and approx. 5-10% of CPU
usage is reduced.
Major improvement is observed in 1-hop Mesh mode topology in 11ACVHT80.
Compared to Infra mode, CPU overhead is higher in Mesh mode due to path
lookup and no fast-xmit support. So reducing spin lock contention is
helping in Mesh.
TOT +change
-------- --------
TCP DL 545 Mbps 595 Mbps
TCP UL 555 Mbps 585 Mbps
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
'WMI_10_4_WDS_PEER_EVENTID' is not yet handled/implemented for WDS mode,
as of now suppress the warning message "Unknown eventid: 36903"
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Recent commit 46f6b06050 ("mac80211: Encrypt "Group addressed privacy" action
frames") encrypts group privacy action frames. But qca99x0 family chipset
delivers broadcast/multicast management frames as encrypted and it should be
decrypted by mac80211. Setting RX_FLAG_DECRYPTED stats for those frames is
breaking mesh connection establishment.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
With the %pK format specifier we hide the kernel addresses
with the help of kptr_restrict sysctl.
In this patch, %p is changed to %pK in the driver code.
The sysctl is documented in Documentation/sysctl/kernel.txt.
Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WMI_SERVICE_PERIODIC_CHAN_STAT_SUPPORT service has missed in
the commit 7e247a9e88 ("ath10k: add dynamic tx mode switch
config support for qca4019"). This patch adds the service to
avoid mismatch between host and target.
Fixes: 7e247a9e88 ("ath10k: add dynamic tx mode switch config support for qca4019")
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Michal Kazior