Replace /include/ by #include for da850 device tree files, in order to
use the C pre-processor, making use of #define features possible.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This revamps the device tree to fit with the new clock
implementation and brings it quite a bit closer to how
the hardware actually works.
After this the clock implementation knows about all
clock gates and will gate off all unused clocks at
boot time and save a bit of power.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* New SoCs i.MX6 Sololite and Vybrid VF610 support
* imx5 and imx6 clock fixes and additions
* Update clock driver to use of_clk_init() function
* Refactor restart routine mxc_restart() to get it work for DT boot
as well
* Clean up mxc specific ulpi access ops
* imx defconfig updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRvsJmAAoJEFBXWFqHsHzOHOIH/jjVCaAFdOskPI4d9qPPAt9C
5o0aJDjerzTm+vH2mbec2507fChaYrLybAypJUj6wDYRf03RhAgPXorY83Y+3WtG
SYz2UWza7MY8GeZv6e9tdrYS3JUSicFXPf8MsOcINsuyIub3dD96z36OqrnWZLFy
uH5V81e4gOHECd4PWIxmhdjwawqmwb/Pqzl0V3+vXi2JM07xrn7/SqlZ7VfUwM2q
DNhu5ugH7FtaFp75YrmTIhp6i+tovguRr0RIt6dnk/9gbJBQnV2Cw2MzdRPT12U5
bC79P7sojkKRtITcq9c1fnUNhkgc0+hS8HoezcQmzKMin6nFmVAh5wQFSlRJMJE=
=mZw+
-----END PGP SIGNATURE-----
Merge tag 'imx-soc-3.11' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/soc
From Shawn Guo:
imx soc changes for 3.11:
* New SoCs i.MX6 Sololite and Vybrid VF610 support
* imx5 and imx6 clock fixes and additions
* Update clock driver to use of_clk_init() function
* Refactor restart routine mxc_restart() to get it work for DT boot
as well
* Clean up mxc specific ulpi access ops
* imx defconfig updates
* tag 'imx-soc-3.11' of git://git.linaro.org/people/shawnguo/linux-2.6: (29 commits)
ARM: imx_v6_v7_defconfig: Enable Vybrid VF610
ARM: imx_v6_v7_defconfig: Enable imx-wm8962 by default
ARM: clk-imx6qdl: Add clko1 configuration for imx6qdl-sabresd
ARM: imx_v6_v7_defconfig: Enable PWM and backlight options
ARM: imx: Remove mxc specific ulpi access ops
ARM: imx: add initial support for VF610
ARM: imx: add VF610 clock support
ARM: imx_v6_v7_defconfig: enable parallel display
ARM: imx: clk: No need to initialize phandle struct
ARM: imx: irq-common: Include header to avoid sparse warning
ARM: imx: Enable mx6 solo-lite support
ARM: imx6: use common of_clk_init() call to initialize clocks
ARM: imx6q: call of_clk_init() to register fixed rate clocks
ARM: imx: imx_v6_v7_defconfig: Select CONFIG_DRM_IMX_TVE
ARM: i.MX6: clk: add different DualLite MLB clock config
ARM i.MX5: Add S/PDIF clocks
ARM i.MX53: Add SATA clock
ARM: imx6q: clk: add the eim_slow clock
ARM: imx: remove MLB PLL from pllv3
ARM: imx: disable pll8_mlb in mx6q_clks
...
Conflicts:
arch/arm/Kconfig.debug (simple add/add conflict)
Includes an update to 3.10-rc6
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* A bunch of new board additions, imx6sl-evk, vf610-twr, imx53-tx53,
imx53-m53evk and imx27-phytec-phycore
* Various pinctrl setting updates and additions
* Enable various on board peripherals, usb, audio, nor, display etc.
* Configure L2 cache data and tag latency from device tree
* Add imx-weim bus driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRvsoqAAoJEFBXWFqHsHzOWCsIAIhbVAz9Q/HvRrrT2/viiu5G
S6/O16PbTqCmRPOgjnABGNOzRxo94/abhYT7gbGDz/zqAK2wEzEtUMwX8SXJbvl2
ynt4oX/QTgeQsZZXW+dCdet6XiBSJwfbFFo0c01pCBvPb7os739pO3u3CUvNeqKx
vsEfiq190PSPVL0FdfyLpQB+64ApUB1L/Ez9BaWmJjQYN2LWM0lxyvbC0SPo1vrw
eb8NJ7qz/qq3zXCKgD8LEvkfal4ZsezPYzap1sqKl1+T2aN4CsgzYaRra/wDv7BC
0ssW3+11StrwrbdwOEQRwiSU15fc9ckVldoFGlB+9HKTZxh80u0HmZRvFWbWo0E=
=jngF
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-3.11' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/dt
From Shawn Guo:
imx device tree changes for 3.11:
* A bunch of new board additions, imx6sl-evk, vf610-twr, imx53-tx53,
imx53-m53evk and imx27-phytec-phycore
* Various pinctrl setting updates and additions
* Enable various on board peripherals, usb, audio, nor, display etc.
* Configure L2 cache data and tag latency from device tree
* Add imx-weim bus driver
* tag 'imx-dt-3.11' of git://git.linaro.org/people/shawnguo/linux-2.6: (82 commits)
ARM: dts: imx27: Add VPU devicetree node
ARM: mxc: fix gpio-ranges for VF610
ARM: dtsi: imx6qdl-sabresd: Enable WM8962 audio support
ARM: dtsi: imx6qdl-sabresd: Enable SSI2 and AUDMUX
ARM: dtsi: imx6qdl-sabresd: Add WM8962 CODEC support
ARM: dtsi: imx6qdl-sabresd: add a fixed regulator for WM8962
ARM: dtsi: imx6dl: Add a pinctrl for AUDMUX
ARM: dtsi: imx6q/imx6dl: Add a pinctrl for I2C1
ARM: dts: imx6qdl-sabresd: add clko1 iomux configuration
ARM: dts: Phytec imx6q pfla02 and pbab01 support
ARM: dts: imx6q: Add pinctrl for usdhc2 and enet
ARM: dts: imx27-phytec-phycore-rdk: Add MTD name for NOR flash
ARM: dts: imx27-phytec-phycore-rdk: Add SDHC support
ARM: dts: i.MX27: Add SDHC devicetree nodes
ARM: dts: i.MX27: Add DMA devicetree node
ARM: dts: imx6qdl-sabreauto: enable the WEIM NOR
ARM: dts: imx6dl: add pinctrls for WEIM NOR
ARM: dts: imx6q: add pinctrls for WEIM NOR
ARM: dts: imx6qdl: add more information for WEIM
ARM: dts: imx6q{dl}: fix the pin conflict between SPI and WEIM
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* A couple of new board support, cfa10055 and cfa10057
* A few updates on cfa10036 device tree source
* Some auart pinctrl data addition
* Adopt soc bus infrastructure for mach-mxs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRvwUEAAoJEFBXWFqHsHzOZXgH/jYs9okBIb6UtYegmdGUinCD
VHJJT+RT8ceosMjBt+aBfpKplUG1X3OOoWbpU7Uv5JKNfY+0QbYTr4bdSE0YTF19
/ml5lCLLqW1MouErxIIe9yFrs4ZhZLLuW0Uy+ze7XVO/VPUlmJWYGU4D5gLcN+SH
aDdwAfe0SEydxWKp5euh6O2qPuuOro5/kUOPvYs6xaJj3marWkD9M6YyhaWvaFwF
2iUWzSd6dGabHRYwG2r38IlKMo6xncnu3b1NPifVMiPtiHFJ8t0SyTEGmpq19G+x
G6q0TneOUVIgH0PN4YQoCGOR6oAB52Z/dVTVlGx6LE6w9Q95wI3XNHltP5U+bF0=
=Oeyn
-----END PGP SIGNATURE-----
Merge tag 'mxs-dt-3.11' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/dt
From Shawn Guo:
mxs device tree changes for 3.11:
* A couple of new board support, cfa10055 and cfa10057
* A few updates on cfa10036 device tree source
* Some auart pinctrl data addition
* Adopt soc bus infrastructure for mach-mxs
* tag 'mxs-dt-3.11' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: mxs: dt: Add Crystalfontz CFA-10057 device tree
ARM: mxs: dt: Add the Crystalfontz CFA-10055 device tree
ARM: cfa10049: Switch the chip select pin of the LCD controller
ARM: cfa10036: Add USB0 OTG port
ARM: dts: apf28dev: Add touchscreen support for APF28dev
ARM: mxs: Fix UARTs on M28EVK
ARM: cfa10036: dt: Change i2c0 clock frequency
ARM: dts: cfa10036: Change the OLED display to SSD1306
ARM: mx28: add auart4 2 pins pinmux to imx28.dtsi
ARM: mx28: add auart3 2 pins pinmux to imx28.dtsi
ARM: mx28: add auart2 2 pins pinmux to imx28.dtsi
ARM: mxs: Use soc bus infrastructure
ARM: dts: mx28: Adjust the digctl compatible string
ARM: mxs: Remove init_irq declaration in machine description
Includes an update to 3.10-rc6
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Add devicetree support to timer, pinctrl (probe), I2C block,
watchdog, DMA controller and clocks.
- Piecewise add a device tree containing all peripherals.
- Delete the ATAG boot path.
- Delete redundant platform data and board files.
- Convert to multiplatform.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=fstd
-----END PGP SIGNATURE-----
Merge tag 'u300-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/soc
From Linus Walleij:
Device Tree and Multiplatform support for U300:
- Add devicetree support to timer, pinctrl (probe), I2C block,
watchdog, DMA controller and clocks.
- Piecewise add a device tree containing all peripherals.
- Delete the ATAG boot path.
- Delete redundant platform data and board files.
- Convert to multiplatform.
* tag 'u300-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson: (40 commits)
ARM: u300: switch to using syscon regmap for board
ARM: u300: Update MMC configs for u300 defconfig
spi: pl022: use DMA by default when probing from DT
pinctrl: get rid of all platform data for coh901
ARM: u300: convert MMC/SD clock to device tree
ARM: u300: move the gated system controller clocks to DT
i2c: stu300: do not request a specific clock name
clk: move the U300 fixed and fixed-factor to DT
ARM: u300: remove register definition file
ARM: u300: add syscon node
ARM: u300 use module_spi_driver to register driver
ARM: u300: delete remnant machine headers
ARM: u300: convert to multiplatform
ARM: u300: localize <mach/u300-regs.h>
ARM: u300: delete <mach/irqs.h>
ARM: u300: delete <mach/hardware.h>
ARM: u300: push down syscon registers
ARM: u300: remove deps from debug macro
ARM: u300: move debugmacro to debug includes
ARM: u300: delete all static board data
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Conflicts:
drivers/net/wireless/ath/ath9k/Kconfig
drivers/net/xen-netback/netback.c
net/batman-adv/bat_iv_ogm.c
net/wireless/nl80211.c
The ath9k Kconfig conflict was a change of a Kconfig option name right
next to the deletion of another option.
The xen-netback conflict was overlapping changes involving the
handling of the notify list in xen_netbk_rx_action().
Batman conflict resolution provided by Antonio Quartulli, basically
keep everything in both conflict hunks.
The nl80211 conflict is a little more involved. In 'net' we added a
dynamic memory allocation to nl80211_dump_wiphy() to fix a race that
Linus reported. Meanwhile in 'net-next' the handlers were converted
to use pre and post doit handlers which use a flag to determine
whether to hold the RTNL mutex around the operation.
However, the dump handlers to not use this logic. Instead they have
to explicitly do the locking. There were apparent bugs in the
conversion of nl80211_dump_wiphy() in that we were not dropping the
RTNL mutex in all the return paths, and it seems we very much should
be doing so. So I fixed that whilst handling the overlapping changes.
To simplify the initial returns, I take the RTNL mutex after we try
to allocate 'tb'.
Signed-off-by: David S. Miller <davem@davemloft.net>
The branch contains:
- DT uart handling cleanup
- Support for zc706 and zed board
- Removal of board compatible string
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iEYEABECAAYFAlG+ysgACgkQykllyylKDCENewCgk3LUwpMxepV1JOaNBmUJ0A09
jtMAnA395sve+FBxYjfM+nSAmbnl5RYl
=KBrZ
-----END PGP SIGNATURE-----
Merge tag 'zynq-dt-for-3.11' of git://git.xilinx.com/linux-xlnx into next/dt
From Michal Simek:
arm: Xilinx Zynq dt changes for v3.11
The branch contains:
- DT uart handling cleanup
- Support for zc706 and zed board
- Removal of board compatible string
* tag 'zynq-dt-for-3.11' of git://git.xilinx.com/linux-xlnx:
arm: dt: zynq: Add support for the zed platform
arm: dt: zynq: Add support for the zc706 platform
arm: dt: zynq: Use 'status' property for UART nodes
arm: zynq: Remove board specific compatibility string
clk: zynq: Remove deprecated clock code
arm: zynq: Migrate platform to clock controller
clk: zynq: Add clock controller driver
clk: zynq: Factor out PLL driver
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Pulls the Integrator/AP PCI bridge driver into one file
- Adds full device tree support for it
- Keeps ATAG support around for the time being
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=bzpe
-----END PGP SIGNATURE-----
Merge tag 'integrator-pci-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/soc
From Linus Walleij:
This is a patch series that:
- Pulls the Integrator/AP PCI bridge driver into one file
- Adds full device tree support for it
- Keeps ATAG support around for the time being
* tag 'integrator-pci-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: integrator: basic PCIv3 device tree support
ARM: integrator: move static ioremapping into PCIv3 driver
ARM: integrator: move VGA base assignment
ARM: integrator: remap PCIv3 base dynamically
ARM: integrator: move V3 register definitions into driver
ARM: integrator: move PCI base address grab to probe
ARM: integrator: grab PCI error IRQ in probe()
ARM: integrator: convert PCIv3 bridge to platform device
ARM: integrator: merge PCIv3 driver into one file
ARM: pci: create pci_common_init_dev()
Documentation/devicetree: add a small note on PCI
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
USB Host PHY clock on port 2 must be configured to 19.2MHz.
Provide this information.
Cc: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
On Panda the +5V supply for DVI EDID is supplied by the
same regulator that poweres the USB Hub. Currently, the
DSS/DVI subsystem doesn't know how to manage this regulator
and so DVI EDID reads will fail if USB Hub is not enabled.
As a temporary fix we keep this regulator permanently enabled
on boot. This fixes the DVI EDID read problem.
CC: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Provide the RESET and Power regulators for the USB PHY,
the USB Host port mode and the PHY device.
Also provide pin multiplexer information for the USB host
pins.
HACK: The reset control need to be replaced with the proper
gpio-controlled reset driver as soon it will be merged [1].
[1] http://thread.gmane.org/gmane.linux.drivers.devicetree/36830
Signed-off-by: Roger Quadros <rogerq@ti.com>
[benoit.cousson@linaro.org: Add disclaimer about the reset control
inside changelog and code]
Cc: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Pull ARM fixes from Russell King:
"The larger changes this time are
- "ARM: 7755/1: handle user space mapped pages in flush_kernel_dcache_page"
which fixes more data corruption problems with O_DIRECT
- "ARM: 7759/1: decouple CPU offlining from reboot/shutdown" which
gets us back to working shutdown/reboot on SMP platforms
- "ARM: 7752/1: errata: LoUIS bit field in CLIDR register is incorrect"
which fixes a shutdown regression found in v3.10 on Versatile
Express platforms.
The remainder are the quite small, maybe one or two line changes"
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7759/1: decouple CPU offlining from reboot/shutdown
ARM: 7756/1: zImage/virt: remove hyp-stub.S during distclean
ARM: 7755/1: handle user space mapped pages in flush_kernel_dcache_page
ARM: 7754/1: Fix the CPU ID and the mask associated to the PJ4B
ARM: 7753/1: map_init_section flushes incorrect pmd
ARM: 7752/1: errata: LoUIS bit field in CLIDR register is incorrect
The Armada 370 RD board has two internal mini-PCIe connectors. This
commit adds the necessary Device Tree informations to enable the usage
of those mini-PCIe connectors.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add the required pin configuration support to EXYNOS5420
using pinctrl interface.
Signed-off-by: Leela Krishna Amudala <l.krishna@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Tested-by : Sunil Joshi <joshi@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add AM43x ePOS EVM minimal DT source - this is a minimal one to get
it booting. Also include it in omap2plus dtbs and document bindings.
The hardware is under development.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add bandgap device DT entry for OMAP5 dtsi.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: J Keerthy <j-keerthy@ti.com>
[benoit.cousson@linaro.org: Fix alignement and use the macros
for IRQ attributes]
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add pinmux configurations for RGMII based CPSW ethernet to am335x-evm.
Default mode is nothing but the values required for the module during
active state. With this configurations module is functional as
expected.
Sleep mode is nothing but the values required for the module during
inactive state. The pins are configured to its reset state to optimize
energy usage for the pins for the suspend/resume cycle
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add pinmux configurations for RGMII based CPSW ethernet to AM335x EVMsk.
Default mode is nothing but the values required for the module during
active state. With this configurations module is functional as
expected.
Sleep mode is nothing but the values required for the module during
inactive state. The pins are configured to its reset state to optimize
energy usage for the pins for the suspend/resume cycle
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add pinmux configurations for MII based CPSW ethernet to am335x-bone.
Default mode is nothing but the values required for the module during
active state. With this configurations module is functional as
expected.
Sleep mode is nothing but the values required for the module during
inactive state. The pins are configured to its reset state to optimize
energy usage for the pins for the suspend/resume cycle
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Commit c971ff1 'leds: leds-pwm: Defer led_pwm_set() if PWM can sleep'
fixed a crash when using a trigger with a pwm-led provided by an
external chip. Now it is safe to add the default trigger according
to board-overo.c.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
The LED is active low, not active high.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
The Tobi expansion boards embeds a SMSC LAN8700 PHY. Add the
corresponding node into the DT. The regulators are not designed
to be turned off.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Some nodes in OMAP3 DTS now use edge or level sensitive interrupts.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add Palmas MFD node and the regulator nodes for OMAP5.
The node definitions are based on: https://lkml.org/lkml/2013/6/6/25
Boot tested on omap5-uevm board.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
PWM output from ecap2 uses as backlight source. Also adds low threshold
value to have a uniform divisions in brightness-levels scales with
inverse polarity.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Reviewed-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
PWM output from ecap0 uses as backlight source. Also adds low threshold
value to have a uniform divisions in brightness-levels scales.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Reviewed-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add PWMSS device tree nodes in relation with ECAP & EHRPWM DT nodes to
AM33XX SoC family. Also populates device tree nodes for ECAP & EHRPWM by
adding necessary properties like pwm-cells, base reg & set disabled as
status.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Reviewed-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add the bandgap entry for OMAP4430 devices.
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Russell King <linux@arm.linux.org.uk>
[benoit.cousson@linaro.org: Add blank line and fix reg presentation]
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
On most OMAP3 platforms, the twl4030 IRQ line is connected to the
SYS_NIRQ line on OMAP. Add another DTS include file
(twl4030_omap3.dtsi) for boards that hook up the twl4030 this way
to include.
This allows RTC wake from off-mode to work again on OMAP3-based
platforms with twl4030. Tested on 3530/Beagle, 3730/Beagle-xM,
3530/Overo, 3730/Overo-STORM.
Special thanks to Florian Vaussard for suggesting use of preprocessor
feature.
Cc: Florian Vaussard <florian.vaussard@epfl.ch>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Using the gpio-keys bindings, configure the user button on Beagle
boards. Since the user button is enabled as a wakeup source, also
ensure the GPIO pin is mux'd correctly and has IO ring wakeups enabled,
so it can also wakeup from off mode.
Special thanks to Florian Vaussard for suggesting the preprocessor
feature.
Cc: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Ensure the console uart (UART3) on these boards is mux'd correctly, and
IO ring wakeup is enabled.
This is needed for serial console wakeups when using DT boot.
Thanks to Florian Vaussard for suggestion to use preprocessor
features.
Cc: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Booting omap5 uevm results in the following error
"did not get pins for uart error: -19"
This happens because omap5 uevm dts file is not adapted
to use uart through pinctrl framework.
Populate uart pinctrl data to get rid of the error.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
[r.sricharan@ti.com: Replaced constants with preprocessor macros]
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add support for blue LED 1 off of GPIO 153.
Make the LED a heartbeat LED
Configure the MUX for GPIO output.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
[r.sricharan@ti.com: Replaced constants with preprocessor macros]
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Provide the RESET regulators for the USB PHYs, the USB Host
port modes and the PHY devices.
Also provide pin multiplexer information for the USB host
pins.
Signed-off-by: Roger Quadros <rogerq@ti.com>
[r.sricharan@ti.com: Replaced constants with preprocessor macros]
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
The uevm is the only official board supported for the OMAP5 soc
in mainline. The existent sevm platform will no more be supported.
Hence cleaning up the board dts file to have only the data
required for uevm.
Renaming the board dts file and adding the following cleanups.
* There are no devices connected on I2C 2,3,4 buses. So remove
the pinmux data for the same.
* OMAP5432 and DDR3 memory is used in the uevm. Temperature polling
is not supported with DDR3 memories. Because of DDR3 phy limitation
the voltage change across DVFS and all shadow registers for DVFS on
DDR3 is not supported. Hence the emif kernel driver is not required,
so removing the DDR3 device file and emif nodes for uevm.
* Keypad is not supported on uevm. So remove the device node.
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
When making the dtbs target on OMAP/AM35xx, some trees are not
built.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Using constants for pinctrl allows a better readability, and removes
redundancy with comments.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Tested-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Use standard GPIO constants to enhance the readability of DT GPIOs.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Tested-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Replace /include/ by #include for AM33XX and AM35XX device tree
files, in order to use the C pre-processor, making use of #define
features possible.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Tested-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
DT source (minimal) for AM4372 SoC to represent AM43x SoC's. Those
represented here are the minimal DT nodes necessary to get kernel
booting.
In DT nodes, "ti,hwmod" property has not been added, this would be
added along with PRCM support for AM43x.
Signed-off-by: Ankur Kishore <a-kishore@ti.com>
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Update the dt property ti,audpwron-gpio to use the
gpio macro definition for GPIO_ACTIVE_HIGH.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
The GPIO for LED D1 on the omap4-panda a1-a3 rev and the omap4-panda-es
are different.
A1-A3 = gpio_wk7
ES = gpio_110
There is no change to LED D2
Abstract away the pinmux and the LED definitions for the two boards into
the respective DTS files.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Using constants for pinctrl allows a better readability, and removes
redundancy with comments.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Use the constants defined in include/dt-bindings/interrupt-controller/
to enhance readability.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Use standard GPIO constants to enhance the readability of DT GPIOs.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Replace /include/ by #include for OMAP2+ DT, in order to use the
C pre-processor, making use of #define features possible.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
GPMC controller on AM335x-EVM has a NAND flash connected to it.
This patch updates following in am335x-evm.dts:
- adds nandflash specific pin-mux configs
- adds nand node as child of GPMC contoller, with information about
NAND flash interface, NAND partition table, ECC scheme, elm handle id.
- updates GPMC node for newer GPMC DT properties added in linux-3.10.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Gupta, Pekon <pekon@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
ELM hardware engine is used for locating bit-flips in NAND data
This patch is required for working of hardware based NAND ECC schemes
with DT support.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
The IGEP COM Module has an 512MB NAND flash memory.
Add a device node for this NAND and its partition layout.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
The IGEPv2 board has an 512MB NAND flash memory.
Add a device node for this NAND and its partition layout.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
The IGEPv2 board has an SMSC LAN9221i ethernet chip connected to
the OMAP3 processor though the General-Purpose Memory Controller.
This patch adds a device node for the ethernet chip as a GPMC child
and all its dependencies (regulators, GPIO and pin muxs).
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
xdma_event_intr1.clkout2 pad can be used to source clock
from either 32K OSC or any of the PLL (except MPU) outputs.
On the existing AM335x based boards (EVM, EVM-SK and Bone),
this pad is used to feed the clock to audio codes.
So, this patch configures the pinmux to get clkout2 on the pad.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add pin control binding for UART0 device nodes in all
board specific DT files.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Matt Porter <mporter@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
With DT support, where naming convention is based on base-addr
and not id, so we should follow TRM/Spec numbering label.
This patch changes UART numbering as per TRM, as uart0-5.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Matt Porter <mporter@ti.com>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Now gpio-leds driver is using devm_pinctrl_get_select_default()
api to set default pinmux configuration required for the
functionality of the driver, so this patch moves respective
pinctrl binding inside leds node.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add pin control binding for I2C device nodes in all
board specific DT files (as per current usage),
EVM: Both i2c0 and i2c1
EVM-SK and Bone: Only i2c0
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Matt Porter <mporter@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
The carveouts that have been reserved for multimedia usecases
are not being used currently by any driver and so have been
cleaned up. Memory will be allocated runtime through CMA for
enabling the multimedia usecases.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add initial device tree nodes for EXYNOS5420 SoC and SMDK5420 board.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Instead of having to specify the number for CPUs in EXYNOS5250 in
platsmp.c file, let the number of CPUs be determined by having this
information listed in EXYNOS5250 device tree file.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
In preparation of adding support for EXYNOS5420, which has many
peripherals similar to EXYNOS5250, a new common EXYNOS5 device tree
source file is created out of the exising EXYNOS5250 device tree
source file. Only the common nodes required for basic boot up on
EXYNOS5420 based boards are moved into this new file and the rest
of the common nodes would be moved subsequently.
EXYNOS5440 SoC is quite different from EXYNOS5250 and EXYNOS5420.
Hence it is not possible to reuse "exynos5.dtsi" for EXYNOS5440.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add clock lookup information for i2s controllers on exynos5250 SoC.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Audio subsystem introduced in s5pv210 and exynos platforms
which has a internal clock controller. This patch adds a node
for the same on exynos5250.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Replace /include/ (dtc) with #include (C pre-processor) for all
Samsung DT files
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The LDO for LCD driver is currently not handled by any of the drivers.
This disables the LDO during booting time. To fix this, the LDO
is forced to enabled always.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Commit e45600107b (Merge tag 'msm-cleanup-for-3.11' of
git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm into
next/cleanup) incorrectly resolved a merge conflict, resulting in a
node address that doesn't match the register address.
Fix this node address.
Signed-off-by: David Brown <davidb@codeaurora.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
- Minimal machine and device-tree support with arch_timers and console UART
- Reboot hook using PLL reset
- Low level debug support using UART
- SMP boot support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=pkFT
-----END PGP SIGNATURE-----
Merge tag 'keystone-soc-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/soc
From Santosh Shilimkar:
SOC support for Keystone II devices:
- Minimal machine and device-tree support with arch_timers and console UART
- Reboot hook using PLL reset
- Low level debug support using UART
- SMP boot support
* tag 'keystone-soc-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
ARM: keystone: Enable SMP support on Keystone machines
ARM: keystone: Add minimal TI Keystone platform support
ARM: dts: keystone: Add minimal Keystone SOC device tree data
Signed-off-by: Olof Johansson <olof@lixom.net>
The convention for Device Tree node names is <device>@<hex-address>, where
the part after '@' shouldn't contain the "0x" prefix. Fix the sh73a0.dtsi
DT names.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add minimal device tree data for Keystone2 based SOCs. Patch
contains mainly ARM related SOC data and nothing about EVM specific
yet.
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: arm@kernel.org
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
By default the exynos RTC is disabled. Enable it for snow. There's
also an external RTC on the max77686 PMIC but we haven't yet enabled
that.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The issues reported in commit 522ccdb6fd ("ARM: dts: Disable the RTC
by default on exynos5") are no longer reproduced on EXYNOS5250 based
Arndale board. Hence re-enabling RTC support for Arndale board.
This is helpful for testing S2R on Arndale board.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Since the pdma works only in secure mode, accessing the same
in hypervisor mode gives an abort. As we are not using pdma
anywhere, removing the same.
Signed-off-by: Giridhar Maruthy <giridhar.m@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Since ssdk5440 and sd5v1 have 8GiB memory, this patch
updates bootargs for them.
Signed-off-by: Subash Patel <subash.rp@samsung.com>
Signed-off-by: Jungseok Lee <jays.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch updates cpu frequency level from 1500 to 800MHZ in steps
of 100MHZ. The corresponding voltage(in uV) is also added.
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds the required regulator supplies and properties
for wm8994 codec on smdk5250 board.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch enables the SPI in EXYNOS5440 SoC. The NOR
Flash can be accessed by enabling the spi interface
Signed-off-by: Girish K S <ks.giri@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch corrects the base address of pinctrl_3 on Exynos5250
platform.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This switches the code using a local remapping of the
system controller to enable the U300 board to be
self-powered over to making the U300-specific syscon
compatible with the MFD generic syscon driver, selecting
the generic syscon driver, and augmenting the board
power code to pick the regmap and manipulate the syscon
from the regmap side of things.
Cc: Dong Aisheng <dong.aisheng@linaro.org>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This converts the last of the U300 clocks to being probed from
the device tree.
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the slow, fast, AHB bridge and "rest" clocks on
the U300 system controller over to registration from the
device tree.
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This converts the fixed and fixed-factor clocks in the U300
platform to register themselves from the device tree.
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a device tree node for the U300 system controller
and remaps this dynamically instead of using hard-coded
virtual addresses. The board power set-up code is altered
to fetch a reference to the syscon using ampersand <&syscon>
notation. This way of passing a pointer to the syscon will
also be used by the clocks.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This registers the U300 FSMC flash controller from the
device tree, and defines the three partitions. Skip the
BBT scan as in the current platform data.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This probes the U300 dummy-spichip from the device tree
and adds the apropriate node to the tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This registers the PL022 PrimeCell from the U300 device
tree. We make a new copy of the platform data for the
device tree boot path, as the old platform data is in an
older file which will be going away.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the COH 901 318 DMA controller to the U300
device tree. All devices now converted to device tree
so far will start to find their DMA channels.
Note that the U300 is not yet using the device tree
to obtain DMA channels, but this is a first step.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds DMA channel assignments to the MMC/SD-controller
and the two UARTs already in the U300 device tree, as we
have now defined a way to obtain DMA channels from the
device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds support for the U300 MMC/SD card slot from the device
tree boot. No other changes needed.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that we have enabled board power and the AB3100 regulators,
put the regulator data into the device tree and enable it so
we can start to tie regulators to devices. To begin with we're
only supplying the power to the board itself.
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make sure hyp-stub.S gets removed during make distclean,
this left over file was introduced in commit:
424e599 ARM: zImage/virt: hyp mode entry support for the zImage loader
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Dave Martin <dave.martin@linaro.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a DT fragment for the Zed Zynq platform and a corresponding
target to the Makefile
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add a DT fragment for the zc706 Zynq platform and a corresponding
target to the Makefile.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Set the default status for UARTs to disabled in the zynq-7000.dtsi file
and let board dts files enable the UARTs on demand.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When zImage is loaded into RAM at a low address but TEXT_OFFSET
is set higher, we risk overwriting ourself with the page table
needed to turn on the cache as it is located relative to the relocation
address. Let's defer the cache setup after relocation in that case.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Reported-by: Stephen Boyd <sboyd@codeurora.org>
Tested-by: Stephen Boyd <sboyd@codeurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the missing VPU devicetree node for i.MX27 CPUs.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The gpio-ranges properties in vf610.dtsi were written according to an
older version of the GPIO bindings. Unfortunately, these were changed
incompatibly in commit 86853c8 "gpio: add gpio offset in gpio range
cells property". This patch adds the missing required extra cell in each
gpio-ranges property.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
On Sabre SD, system controls WM8962 power by pulling up/down GPIO_4_10,
so add a regulator controled by GPIO_4_10 for WM8962.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Setting GPIO_0 pad as clko1 clock output to provide MCLK for WM8962.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds name for NOR flash. This keeps compatibility for
commandline partitions parsing from old bootloaders and make name
of device same for DT and non-DT boot.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutonix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Enable the WEIM NOR for imx6q{dl}-sabreauto boards.
For the pin conflict with SPI NOR, its status is set to "disabled".
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add two pinctrls for WEIM:
one for the weim nor, another for the chipselect.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add two pinctrls for WEIM:
one for the weim nor, another for the chipselect.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add the clock and compatible information for the weim.
Also adds the weim label.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
In the imx6q-sabreauto and imx6dl-sabreauto boards,
the pin MX6Q{DL}_PAD_EIM_D19 is used as a GPIO for SPI NOR, but
it is used as a data pin for the WEIM NOR.
In order to fix the conflict, this patch removes the pin from the hog,
and adds a new board-level pinctrl: pinctrl_ecspi1_sabreauto.
The SPI NOR selects this pinctrl_ecspi1_sabreauto when it is enabled.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
use NO_PAD_CTL / 0x80000000 instead of 0x10000 to prevent misconfigured pads
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
[Steffen: split up patch into tqma53+mba53 part]
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add properties to make use of pca9554 gpio expander.
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Enable the sgtl5000 found on MBa53 mainboard.
Also enable audio muxer and ssi, which are needed for sound to work.
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
As the displays are optional and we have more than one, also
set the status of the parallel display and the ldb to disabled.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This adds the Television Encoder (TVEv2) device tree node
to the i.MX53 dtsi.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
I2S_MCLK is moved from pad GPIO19 to GPIO0, which can be muxed to the
ssi_ext1 clock signal. #SYSTEM_DOWN is moved from pad GPIO0 to GPIO19.
Add #PHY_RESET and LCD_CONTRAST.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Patch adds initial dts for Phytec PCM970 Rapid development kit.
- Added definition for UART0 and UART1.
- Added additional SPI chipselect which used on RDK for ZegBee module.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
UART1 and UART2 can be unused on some designs with PCM038 module.
Remove these definitions from basic dts and lets choose user only
necessary UARTs in custom designs.
Keep UART0 for using this one as boot console, but since we have
not way to disable usage RTSCTS signals, remove this parameter for UART0.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
PCM038 dts can be used as base for development kit board or any
custom PCB designs. Renames this file to match functionality.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
FEC (KSZ8001L) reset pin is connected to GPIOC30.
Add this definition to dts.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add a group to the fec pinctrl, for use with MII interface.
Signed-off-by: Jonas Andersson <jonas@microbit.se>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Configure the data and tag latency for the L2 cache. This improves the
system performance.
This configuration is taken from Freescale's kernel patch
"ENGR00153601 [MX6]Adjust L2 cache parameter" [1]
which does
writel(0x132, IO_ADDRESS(L2_BASE_ADDR + L2X0_TAG_LATENCY_CTRL));
writel(0x132, IO_ADDRESS(L2_BASE_ADDR + L2X0_DATA_LATENCY_CTRL));
In this patch we are doing the same via the device tree.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
[1] http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git/commit/arch/arm/mach-mx6/mm.c?h=imx_3.0.35_12.09.01&id=814656410b40c67a10b25300e51b0477b2bb96d1
Since the SPI/NOR has pin conflict with the WEIM NOR,
we disable the spi/nor by default.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The SPI/NOR needs this gpio for CS.
So add this gpio in the hog pinctrl.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The SPI/NOR needs this gpio for CS.
So add this gpio in the hog pinctrl.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The gpmi does not use the MX6Q_PAD_NANDF_CS2__NAND_CE2_B and
MX6Q_PAD_NANDF_CS3__NAND_CE3_B.
Just remove them.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This adds support for the Ka-Ro TX53 System-On-Module.
As a baseboard is needed to operate it, only a *.dtsi and no Makefile entry.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds support for the DENX M53EVK board. The board currently supports
NAND, Ethernet, UART, CAN, I2C.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
With device tree clk lookup support in place, we can move audio codec
clk lookup for ssi_ext1 into device tree now, so that imx53_qsb_init()
can be saved.
Since ssi_ext2 lookup is used nowhere, it gets removed together with
ssi_ext1 lookup from clk driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds pinctrl data for NAND on MX53.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds pinctrl data for different mux of I2C2 on MX53.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds pinctrl data for different mux of I2C1 on MX53.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds pinctrl data for different mux of CAN1 on MX53.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds pinctrl data for the AUDMUX4 on MX53.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This allows to order the i2c character devices correctly,
so that /dev/i2c-0 corresponds to i2c1, /dev/i2c-1 corresponds
to i2c2, and so on. Currently they are ordered by register
address.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The CFA-10057 is a breakout board for the CFA-10036 that has Ethernet,
USB and a 4.3" LCD screen on it.
Signed-off-by: Brian Lilly <brian@crystalfontz.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The CFA-10055 is yet another breakout board for the CFA-10036, and is
basically a CFA-10037, with the screen and LCD controller found on the
CFA-10049.
Signed-off-by: Brian Lilly <brian@crystalfontz.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The early prototypes had the chip select pin for the LCD controller
wired on the GPIO 3-23, while the production run of the CFA-10049 have
this chip select on the GPIO 3-5.
Signed-off-by: Brian Lilly <brian@crystalfontz.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Make use of RTS/CTS lines on AUART0 and register AUART1 and AUART2
which are routed onto a pin header.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The OLED display can work faster. Change the i2c controller clock
frequency to remove the tearing effect that can be seen on the display.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The SSD1307 was used in an early prototype that will never get
distributed. The final board now has a SSD1306 instead, that has its own
power generation unit and thus doesn't need any PWM. The panel attached
to it also changed.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
MX28 has the same DIGCTL block as MX23, so adjust the compatible string to
reflect that.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Another week, another batch of fixes for arm-soc platforms.
Again, nothing controversial. A few more than would be ideal, but all
are valid fixes. In particular the prima2 panic patch is critical since
it fixes a problem where multiplatform kernels panic on all but prima2
hardware.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=c555
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"These are a little later than I planned on since I got caught up with
handling merges for 3.11 most of the week.
Another week, another batch of fixes for arm-soc platforms.
Again, nothing controversial. A few more than would be ideal, but all
are valid fixes. In particular the prima2 panic patch is critical
since it fixes a problem where multiplatform kernels panic on all but
prima2 hardware."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: SAMSUNG: pm: Adjust for pinctrl- and DT-enabled platforms
ARM: prima2: fix incorrect panic usage
arm: mvebu: armada-xp-{gp,openblocks-ax3-4}: specify PCIe range
ARM: Kirkwood: handle mv88f6282 cpu in __kirkwood_variant().
ARM: omap3: clock: fix wrong container_of in clock36xx.c
ARM: dts: OMAP5: Fix missing PWM capability to timer nodes
ARM: dts: omap4-panda|sdp: Fix mux for twl6030 IRQ pin and msecure line
ARM: dts: AM33xx: Fix properties on gpmc node
arm: omap2: fix AM33xx hwmod infos for UART2
ARM: OMAP3: Fix iva2_pwrdm settings for 3703
This registers the memory ranges for I/O, non-prefetched and
prefetched memory and configuration space for the PCIv3 bridge
and let us fetch these basic memory resources from the device
tree in the device tree boot path. Remove the stepping stone
platform device. This is an either/or approach - the platform
data path is mutually exclusive to the plain platform data
path and provided addresses from the device tree have to be
correct.
This adds the interrupt-map property to the PCIv3 DTS file
and makes the bridge obtain mappings from the device tree.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Cubieboard makes use of the first two i2c controllers found on the
Allwinner A10; i2c-0 is used internally for the PMIC, while i2c-1
is exposed on the board headers. This patch enables them in the device
tree.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tomasz Figa <tomasz.figa@gmail.com>
The A13-Olinuxino makes use of the 3 i2c controllers found on the Allwinner
A13. Enable them in the device tree.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tomasz Figa <tomasz.figa@gmail.com>
Arnd Bergmann