Some firmware files trigger a PHY soft reset and don't wait for it to
be finished. PHY register writes directly after applying the firmware
may fail or provide unexpected results therefore. Fix this by waiting
for bit BMCR_RESET to be cleared after applying firmware.
There's nothing wrong with the referenced change, it's just that the
fix will apply cleanly only after this change.
Fixes: 89fbd26cca ("r8169: fix firmware not resetting tp->ocp_base")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is an upper bound to the value that a watermark may hold. That
upper bound is not immediately obvious during configuration, and it
might be possible to have accidental truncation.
Actually this has happened already, add a warning to prevent it from
happening again.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tail dropping is enabled for a port when:
1. A source port consumes more packet buffers than the watermark encoded
in SYS:PORT:ATOP_CFG.ATOP.
AND
2. Total memory use exceeds the consumption watermark encoded in
SYS:PAUSE_CFG:ATOP_TOT_CFG.
The unit of these watermarks is a 60 byte memory cell. That unit is
programmed properly into ATOP_TOT_CFG, but not into ATOP. Actually when
written into ATOP, it would get truncated and wrap around.
Fixes: a556c76adc ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clang static analysis reports this problem:
drivers/net/ethernet/marvell/mvneta.c:3465:2: warning:
Attempt to free released memory
kfree(txq->buf);
^~~~~~~~~~~~~~~
When mvneta_txq_sw_init() fails to alloc txq->tso_hdrs,
it frees without poisoning txq->buf. The error is caught
in the mvneta_setup_txqs() caller which handles the error
by cleaning up all of the txqs with a call to
mvneta_txq_sw_deinit which also frees txq->buf.
Since mvneta_txq_sw_deinit is a general cleaner, all of the
partial cleaning in mvneta_txq_sw_deinit()'s error handling
is not needed.
Fixes: 2adb719d74 ("net: mvneta: Implement software TSO")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix many (lots deleted here) build errors in hinic by selecting NET_DEVLINK.
ld: drivers/net/ethernet/huawei/hinic/hinic_hw_dev.o: in function `mgmt_watchdog_timeout_event_handler':
hinic_hw_dev.c:(.text+0x30a): undefined reference to `devlink_health_report'
ld: drivers/net/ethernet/huawei/hinic/hinic_devlink.o: in function `hinic_fw_reporter_dump':
hinic_devlink.c:(.text+0x1c): undefined reference to `devlink_fmsg_u32_pair_put'
ld: drivers/net/ethernet/huawei/hinic/hinic_devlink.o: in function `hinic_fw_reporter_dump':
hinic_devlink.c:(.text+0x126): undefined reference to `devlink_fmsg_binary_pair_put'
ld: drivers/net/ethernet/huawei/hinic/hinic_devlink.o: in function `hinic_hw_reporter_dump':
hinic_devlink.c:(.text+0x1ba): undefined reference to `devlink_fmsg_string_pair_put'
ld: hinic_devlink.c:(.text+0x227): undefined reference to `devlink_fmsg_u8_pair_put'
ld: drivers/net/ethernet/huawei/hinic/hinic_devlink.o: in function `hinic_devlink_alloc':
hinic_devlink.c:(.text+0xaee): undefined reference to `devlink_alloc'
ld: drivers/net/ethernet/huawei/hinic/hinic_devlink.o: in function `hinic_devlink_free':
hinic_devlink.c:(.text+0xb04): undefined reference to `devlink_free'
ld: drivers/net/ethernet/huawei/hinic/hinic_devlink.o: in function `hinic_devlink_register':
hinic_devlink.c:(.text+0xb26): undefined reference to `devlink_register'
ld: drivers/net/ethernet/huawei/hinic/hinic_devlink.o: in function `hinic_devlink_unregister':
hinic_devlink.c:(.text+0xb46): undefined reference to `devlink_unregister'
ld: drivers/net/ethernet/huawei/hinic/hinic_devlink.o: in function `hinic_health_reporters_create':
hinic_devlink.c:(.text+0xb75): undefined reference to `devlink_health_reporter_create'
ld: hinic_devlink.c:(.text+0xb95): undefined reference to `devlink_health_reporter_create'
ld: hinic_devlink.c:(.text+0xbac): undefined reference to `devlink_health_reporter_destroy'
ld: drivers/net/ethernet/huawei/hinic/hinic_devlink.o: in function `hinic_health_reporters_destroy':
Fixes: 51ba902a16 ("net-next/hinic: Initialize hw interface")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Bin Luo <luobin9@huawei.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Aviad Krawczyk <aviad.krawczyk@huawei.com>
Cc: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethtool manual stated that the tx-timer is the "the amount of time the
device should stay in idle mode prior to asserting its Tx LPI". The
previous implementation for "ethtool --set-eee tx-timer" sets the LPI TW
timer duration which is not correct. Hence, this patch fixes the
"ethtool --set-eee tx-timer" to configure the EEE LPI timer.
The LPI TW Timer will be using the defined default value instead of
"ethtool --set-eee tx-timer" which follows the EEE LS timer implementation.
Changelog V2
*Not removing/modifying the eee_timer.
*EEE LPI timer can be configured through ethtool and also the eee_timer
module param.
*EEE TW Timer will be configured with default value only, not able to be
configured through ethtool or module param. This follows the implementation
of the EEE LS Timer.
Fixes: d765955d2a ("stmmac: add the Energy Efficient Ethernet support")
Signed-off-by: Vineetha G. Jaya Kumaran <vineetha.g.jaya.kumaran@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl93ap4ACgkQSD+KveBX
+j5+eAf/dvxx+WyWr5pV3gxd0x7K/wV+F1JFVe99k8yH6kYbpo56U+oRQGP4kvnG
4Ggb/XE7hSahvReRVD5vn4LKk2RQ/GMWEurF/GQDPklaHZyZHtcI3+2C/azEHnf+
vGgbM1xDT0gNZoa+2pA7LBgruJF/k+gRbth6EHrjlcxqiqt2k4d5Hs0m/Xd5R0TC
D+Yks3uHAOrTiP2idOWNoWmd5AOmh802wX0w4iyKZ9ZfJGMN3t2AKyZDIhNfPyPf
avebIihkr5y5DsYGZE+HjZjK0+vXaKVAGgzDbeLZ2sPVdCJJAFRZptG6mPJ0d0N3
TPwcBZcs5BsJkEQ5XqBA0IwJjksVeA==
=421I
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2020-09-30' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
From: Saeed Mahameed <saeedm@nvidia.com>
====================
This series introduces some fixes to mlx5 driver.
v1->v2:
- Patch #1 Don't return while mutex is held. (Dave)
v2->v3:
- Drop patch #1, will consider a better approach (Jakub)
- use cpu_relax() instead of cond_resched() (Jakub)
- while(i--) to reveres a loop (Jakub)
- Drop old mellanox email sign-off and change the committer email
(Jakub)
Please pull and let me know if there is any problem.
For -stable v4.15
('net/mlx5e: Fix VLAN cleanup flow')
('net/mlx5e: Fix VLAN create flow')
For -stable v4.16
('net/mlx5: Fix request_irqs error flow')
For -stable v5.4
('net/mlx5e: Add resiliency in Striding RQ mode for packets larger than MTU')
('net/mlx5: Avoid possible free of command entry while timeout comp handler')
For -stable v5.7
('net/mlx5e: Fix return status when setting unsupported FEC mode')
For -stable v5.8
('net/mlx5e: Fix race condition on nhe->n pointer in neigh update')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When interface is attached while in promiscuous mode and with VLAN
filtering turned off, both configurations are not respected and VLAN
filtering is performed.
There are 2 flows which add the any-vid rules during interface attach:
VLAN creation table and set rx mode. Each is relaying on the other to
add any-vid rules, eventually non of them does.
Fix this by adding any-vid rules on VLAN creation regardless of
promiscuous mode.
Fixes: 9df30601c8 ("net/mlx5e: Restore vlan filter after seamless reset")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Prior to this patch unloading an interface in promiscuous mode with RX
VLAN filtering feature turned off - resulted in a warning. This is due
to a wrong condition in the VLAN rules cleanup flow, which left the
any-vid rules in the VLAN steering table. These rules prevented
destroying the flow group and the flow table.
The any-vid rules are removed in 2 flows, but none of them remove it in
case both promiscuous is set and VLAN filtering is off. Fix the issue by
changing the condition of the VLAN table cleanup flow to clean also in
case of promiscuous mode.
mlx5_core 0000:00:08.0: mlx5_destroy_flow_group:2123:(pid 28729): Flow group 20 wasn't destroyed, refcount > 1
mlx5_core 0000:00:08.0: mlx5_destroy_flow_group:2123:(pid 28729): Flow group 19 wasn't destroyed, refcount > 1
mlx5_core 0000:00:08.0: mlx5_destroy_flow_table:2112:(pid 28729): Flow table 262149 wasn't destroyed, refcount > 1
...
...
------------[ cut here ]------------
FW pages counter is 11560 after reclaiming all pages
WARNING: CPU: 1 PID: 28729 at
drivers/net/ethernet/mellanox/mlx5/core/pagealloc.c:660
mlx5_reclaim_startup_pages+0x178/0x230 [mlx5_core]
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS
rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
Call Trace:
mlx5_function_teardown+0x2f/0x90 [mlx5_core]
mlx5_unload_one+0x71/0x110 [mlx5_core]
remove_one+0x44/0x80 [mlx5_core]
pci_device_remove+0x3e/0xc0
device_release_driver_internal+0xfb/0x1c0
device_release_driver+0x12/0x20
pci_stop_bus_device+0x68/0x90
pci_stop_and_remove_bus_device+0x12/0x20
hv_eject_device_work+0x6f/0x170 [pci_hyperv]
? __schedule+0x349/0x790
process_one_work+0x206/0x400
worker_thread+0x34/0x3f0
? process_one_work+0x400/0x400
kthread+0x126/0x140
? kthread_park+0x90/0x90
ret_from_fork+0x22/0x30
---[ end trace 6283bde8d26170dc ]---
Fixes: 9df30601c8 ("net/mlx5e: Restore vlan filter after seamless reset")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Verify the configured FEC mode is supported by at least a single link
mode before applying the command. Otherwise fail the command and return
"Operation not supported".
Prior to this patch, the command was successful, yet it falsely set all
link modes to FEC auto mode - like configuring FEC mode to auto. Auto
mode is the default configuration if a link mode doesn't support the
configured FEC mode.
Fixes: b5ede32d33 ("net/mlx5e: Add support for FEC modes based on 50G per lane links")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Declare GRE offload support with respect to the inner protocol. Add a
list of supported inner protocols on which the driver can offload
checksum and GSO. For other protocols, inform the stack to do the needed
operations. There is no noticeable impact on GRE performance.
Fixes: 2729984149 ("net/mlx5e: Support TSO and TX checksum offloads for GRE tunnels")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The cited commit introduced the following coverity issue at function
mlx5_tc_ct_rule_to_tuple_nat:
- Memory - corruptions (OVERRUN)
Overrunning array "tuple->ip.src_v6.in6_u.u6_addr32" of 4 4-byte
elements at element index 7 (byte offset 31) using index
"ip6_offset" (which evaluates to 7).
In case of IPv6 destination address rewrite, ip6_offset values are
between 4 to 7, which will cause memory overrun of array
"tuple->ip.src_v6.in6_u.u6_addr32" to array
"tuple->ip.dst_v6.in6_u.u6_addr32".
Fixed by writing the value directly to array
"tuple->ip.dst_v6.in6_u.u6_addr32" in case ip6_offset values are
between 4 to 7.
Fixes: bc562be967 ("net/mlx5e: CT: Save ct entries tuples in hashtables")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Prior to this fix, in Striding RQ mode the driver was vulnerable when
receiving packets in the range (stride size - headroom, stride size].
Where stride size is calculated by mtu+headroom+tailroom aligned to the
closest power of 2.
Usually, this filtering is performed by the HW, except for a few cases:
- Between 2 VFs over the same PF with different MTUs
- On bluefield, when the host physical function sets a larger MTU than
the ARM has configured on its representor and uplink representor.
When the HW filtering is not present, packets that are larger than MTU
might be harmful for the RQ's integrity, in the following impacts:
1) Overflow from one WQE to the next, causing a memory corruption that
in most cases is unharmful: as the write happens to the headroom of next
packet, which will be overwritten by build_skb(). In very rare cases,
high stress/load, this is harmful. When the next WQE is not yet reposted
and points to existing SKB head.
2) Each oversize packet overflows to the headroom of the next WQE. On
the last WQE of the WQ, where addresses wrap-around, the address of the
remainder headroom does not belong to the next WQE, but it is out of the
memory region range. This results in a HW CQE error that moves the RQ
into an error state.
Solution:
Add a page buffer at the end of each WQE to absorb the leak. Actually
the maximal overflow size is headroom but since all memory units must be
of the same size, we use page size to comply with UMR WQEs. The increase
in memory consumption is of a single page per RQ. Initialize the mkey
with all MTTs pointing to a default page. When the channels are
activated, UMR WQEs will redirect the RX WQEs to the actual memory from
the RQ's pool, while the overflow MTTs remain mapped to the default page.
Fixes: 73281b78a3 ("net/mlx5e: Derive Striding RQ size from MTU")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Increase granularity of the error path to avoid unneeded free/release.
Fix the cleanup to be symmetric to the order of creation.
Fixes: 0ddf543226 ("xdp/mlx5: setup xdp_rxq_info")
Fixes: 422d4c401e ("net/mlx5e: RX, Split WQ objects for different RQ types")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
In case of pci is offline reclaim_pages_cmd() will still try to call
the FW to release FW pages, cmd_exec() in this case will return a silent
success without actually calling the FW.
This is wrong and will cause page leaks, what we should do is to detect
pci offline or command interface un-available before tying to access the
FW and manually release the FW pages in the driver.
In this patch we share the code to check for FW command interface
availability and we call it in sensitive places e.g. reclaim_pages_cmd().
Alternative fix:
1. Remove MLX5_CMD_OP_MANAGE_PAGES form mlx5_internal_err_ret_value,
command success simulation list.
2. Always Release FW pages even if cmd_exec fails in reclaim_pages_cmd().
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
It is possible that new command entry index allocation will temporarily
fail. The new command holds the semaphore, so it means that a free entry
should be ready soon. Add one second retry mechanism before returning an
error.
Patch "net/mlx5: Avoid possible free of command entry while timeout comp
handler" increase the possibility to bump into this temporarily failure
as it delays the entry index release for non-callback commands.
Fixes: e126ba97db ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Eran Ben Elisha <eranbe@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Once driver detects a command interface command timeout, it warns the
user and returns timeout error to the caller. In such case, the entry of
the command is not evacuated (because only real event interrupt is allowed
to clear command interface entry). If the HW event interrupt
of this entry will never arrive, this entry will be left unused forever.
Command interface entries are limited and eventually we can end up without
the ability to post a new command.
In addition, if driver will not consume the EQE of the lost interrupt and
rearm the EQ, no new interrupts will arrive for other commands.
Add a resiliency mechanism for manually polling the command EQ in case of
a command timeout. In case resiliency mechanism will find non-handled EQE,
it will consume it, and the command interface will be fully functional
again. Once the resiliency flow finished, wait another 5 seconds for the
command interface to complete for this command entry.
Define mlx5_cmd_eq_recover() to manage the cmd EQ polling resiliency flow.
Add an async EQ spinlock to avoid races between resiliency flows and real
interrupts that might run simultaneously.
Fixes: e126ba97db ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Upon command completion timeout, driver simulates a forced command
completion. In a rare case where real interrupt for that command arrives
simultaneously, it might release the command entry while the forced
handler might still access it.
Fix that by adding an entry refcount, to track current amount of allowed
handlers. Command entry to be released only when this refcount is
decremented to zero.
Command refcount is always initialized to one. For callback commands,
command completion handler is the symmetric flow to decrement it. For
non-callback commands, it is wait_func().
Before ringing the doorbell, increment the refcount for the real completion
handler. Once the real completion handler is called, it will decrement it.
For callback commands, once the delayed work is scheduled, increment the
refcount. Upon callback command completion handler, we will try to cancel
the timeout callback. In case of success, we need to decrement the callback
refcount as it will never run.
In addition, gather the entry index free and the entry free into a one
flow for all command types release.
Fixes: e126ba97db ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
As part of driver unload, it destroys the commands EQ (via FW command).
As the commands EQ is destroyed, FW will not generate EQEs for any command
that driver sends afterwards. Driver should poll for later commands status.
Driver commands mode metadata is updated before the commands EQ is
actually destroyed. This can lead for double completion handle by the
driver (polling and interrupt), if a command is executed and completed by
FW after the mode was changed, but before the EQ was destroyed.
Fix that by using the mlx5_cmd_allowed_opcode mechanism to guarantee
that only DESTROY_EQ command can be executed during this time period.
Fixes: e126ba97db ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Petr reported that after resume from suspend RTL8402 partially
truncates incoming packets, and re-initializing register RxConfig
before the actual chip re-initialization sequence is needed to avoid
the issue.
Reported-by: Petr Tesarik <ptesarik@suse.cz>
Proposed-by: Petr Tesarik <ptesarik@suse.cz>
Tested-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr reported that system freezes on r8169 driver load on a system
using ether_clk. The original change was done under the assumption
that the clock isn't needed for basic operations like chip register
access. But obviously that was wrong.
Therefore effectively revert the original change, and in addition
leave the clock active when suspending and WoL is enabled. Chip may
not be able to process incoming packets otherwise.
Fixes: 9f0b54cd16 ("r8169: move switching optional clock on/off to pll power functions")
Reported-by: Petr Tesarik <ptesarik@suse.cz>
Tested-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mbox implementation in octeontx2 driver has three states
alloc, send and reset in mbox response. VF allocate and
sends message to PF for processing, PF ACKs them back and
reset the mbox memory. In some case we see synchronization
issue where after msgs_acked is incremented and before
mbox_reset API is called, if current execution is scheduled
out and a different thread is scheduled in which checks for
msgs_acked. Since the new thread sees msgs_acked == msgs_sent
it will try to allocate a new message and to send a new mbox
message to PF.Now if mbox_reset is scheduled in, PF will see
'0' in msgs_send.
This patch fixes the issue by calling mbox_reset before
incrementing msgs_acked flag for last processing message and
checks for valid message size.
Fixes: d424b6c02 ("octeontx2-pf: Enable SRIOV and added VF mbox handling")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently in otx2_open on failure of nix_lf_start
transmit queues are not stopped which are already
started in link_event. Since the tx queues are not
stopped network stack still try's to send the packets
leading to driver crash while access the device resources.
Fixes: 50fe6c02e ("octeontx2-pf: Register and handle link notifications")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For TCP/UDP checksum offload feature in Octeontx2
expects L3TYPE to be set irrespective of IP header
checksum is being offloaded or not. Currently for
IPv6 frames L3TYPE is not being set resulting in
packet drop with checksum error. This patch fixes
this issue.
Fixes: 3ca6c4c88 ("octeontx2-pf: Add packet transmission support")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packet replication feature present in Octeontx2
is a hardware linked list of PF and its VF
interfaces so that broadcast packets are sent
to all interfaces present in the list. It is
driver job to add and delete a PF/VF interface
to/from the list when the interface is brought
up and down. This patch fixes the
npc_enadis_default_entries function to handle
broadcast replication properly if packet replication
feature is present.
Fixes: 40df309e41 ("octeontx2-af: Support to enable/disable default MCAM entries")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the driver initializes in safe mode, it will call
ice_set_safe_mode_caps. This results in clearing the capabilities
structures, in order to set them up for operating in safe mode, ensuring
many features are disabled.
This has a side effect of also clearing the capability bits that relate
to NVM update. The result is that the device driver will not indicate
support for unified update, even if the firmware is capable.
Fix this by adding the relevant capability fields to the list of values
we preserve. To simplify the code, use a common_cap structure instead of
a handful of local variables. To reduce some duplication of the
capability name, introduce a couple of macros used to restore the
capabilities values from the cached copy.
Fixes: de9b277ee0 ("ice: Add support for unified NVM update flow capability")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Brijesh Behera <brijeshx.behera@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice driver needs to wait for a firmware response to each command to
write a block of data to the scratch area used to update the device
firmware. The driver currently waits for up to 1 second for this to be
returned.
It turns out that firmware might take longer than 1 second to return
a completion in some cases. If this happens, the flash update will fail
to complete.
Fix this by increasing the maximum time that the driver will wait for
both writing a block of data, and for activating the new NVM bank. The
timeout for an erase command is already several minutes, as the firmware
had to erase the entire bank which was already expected to take a minute
or more in the worst case.
In the case where firmware really won't respond, we will now take longer
to fail. However, this ensures that if the firmware is simply slow to
respond, the flash update can still complete. This new maximum timeout
should not adversely increase the update time, as the implementation for
wait_event_interruptible_timeout, and should wake very soon after we get
a completion event. It is better for a flash update be slow but still
succeed than to fail because we gave up too quickly.
Fixes: d69ea414c9 ("ice: implement device flash update via devlink")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Brijesh Behera <brijeshx.behera@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The VIA Technologies VT8251 South Bridge's integrated Rhine-II
Ethernet MAC comes has a PCI revision value of 0x7c. This was
verified on ASUS P5V800-VM mainboard.
Signed-off-by: Kevin Brace <kevinbrace@bracecomputerlab.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rhine_resume() and rhine_suspend(), the code calls netif_running()
to see if the network interface is down or not. If it is down (i.e.,
netif_running() returning false), they will skip any housekeeping work
within the function relating to the hardware. This becomes a problem
when the hardware resumes from a standby since it is counting on
rhine_resume() to map its MMIO and power up rest of the hardware.
Not getting its MMIO remapped and rest of the hardware powered
up lead to a soft reset failure and hardware disappearance. The
solution is to map its MMIO and power up rest of the hardware inside
rhine_open() before soft reset is to be performed. This solution was
verified on ASUS P5V800-VM mainboard's integrated Rhine-II Ethernet
MAC inside VIA Technologies VT8251 South Bridge.
Signed-off-by: Kevin Brace <kevinbrace@bracecomputerlab.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Functions related to nested interface infrastructure such as
netdev_walk_all_{ upper | lower }_dev() pass both private functions
and "data" pointer to handle their own things.
At this point, the data pointer type is void *.
In order to make it easier to expand common variables and functions,
this new netdev_nested_priv structure is added.
In the following patch, a new member variable will be added into this
struct to fix the lockdep issue.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mistakenly bit 2 was set instead of bit 3 as in the vendor driver.
Fixes: a7a92cf815 ("r8169: sync PCIe PHY init with vendor driver 8.047.01")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If mlxsw_sp_acl_tcam_group_id_get() fails, the mutex initialized earlier
is not destroyed.
Fix this by initializing the mutex after calling the function. This is
symmetric to mlxsw_sp_acl_tcam_group_del().
Fixes: 5ec2ee28d2 ("mlxsw: spectrum_acl: Introduce a mutex to guard region list updates")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver subfolder files refer parent folder includes in an
absolute manner.
Makefile contains a -I for this, but apparently that does not
work if object tree is separated.
Adding srctree to fix that.
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding the support for TBF offload, the improper command version
was added even though the command format is for the V2 of
dpni_set_tx_shaping(). This does not affect the functionality of TBF
since the only change between these two versions is the addition of the
exceeded parameters which are not used in TBF. Still, fix the bug so
that we keep things in sync.
Fixes: 39344a8962 ("dpaa2-eth: add API for Tx shaping")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To start also "phy state machine", with UP state as it should be,
the phy_start() has to be used, in another case machine even is not
triggered. After this change negotiation is supposed to be triggered
by SM workqueue.
It's not correct usage, but it appears after the following patch,
so add it as a fix.
Fixes: 74a992b359 ("net: phy: add phy_check_link_status")
Signed-off-by: Ivan Khoronzhuk <ikhoronz@cisco.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
While unloading the dwmac-intel driver, clk_disable_unprepare() is
being called twice in stmmac_dvr_remove() and
intel_eth_pci_remove(). This causes kernel panic on the second call.
Removing the second call of clk_disable_unprepare() in
intel_eth_pci_remove().
Fixes: 09f012e64e ("stmmac: intel: Fix clock handling on error and remove paths")
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During ice_vsi_setup, if ice_cfg_vsi_lan fails, it does not properly
release memory associated with the VSI rings. If we had used devres
allocations for the rings, this would be ok. However, we use kzalloc and
kfree_rcu for these ring structures.
Using the correct label to cleanup the rings during ice_vsi_setup
highlights an issue in the ice_vsi_clear_rings function: it can leave
behind stale ring pointers in the q_vectors structure.
When releasing rings, we must also ensure that no q_vector associated
with the VSI will point to this ring again. To resolve this, loop over
all q_vectors and release their ring mapping. Because we are about to
free all rings, no q_vector should remain pointing to any of the rings
in this VSI.
Fixes: 5513b920a4 ("ice: Update Tx scheduler tree for VSI multi-Tx queue support")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice_setup_pf_sw function can cause a memory leak if register_netdev
fails, due to accidentally failing to free the VSI rings. Fix the memory
leak by using ice_vsi_release, ensuring we actually go through the full
teardown process.
This should be safe even if the netdevice is not registered because we
will have set the netdev pointer to NULL, ensuring ice_vsi_release won't
call unregister_netdev.
An alternative fix would be moving management of the PF VSI netdev into
the main VSI setup code. This is complicated and likely requires
significant refactor in how we manage VSIs
Fixes: 3a858ba392 ("ice: Add support for VSI allocation and deallocation")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
It appears that the ice_suspend flow is missing a call to pci_save_state
and this is triggering the message "State of device not saved by
ice_suspend" and a call trace. Fix it.
Fixes: 769c500dcc ("ice: Add advanced power mgmt for WoL")
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When calling iavf_resume there was a crash because wrong
function was used to get iavf_adapter and net_device pointers.
Changed how iavf_resume is getting iavf_adapter and net_device
pointers from pci_dev.
Fixes: 5eae00c57f ("i40evf: main driver core")
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
MDIO reads can happen during PHY probing, and printing an error with
dev_err can result in a large number of error messages during device
probe. On a platform with a serial console this can result in
excessively long boot times in a way that looks like an infinite loop
when multiple busses are present. Since 0f183fd151 (net/fsl: enable
extended scanning in xgmac_mdio) we perform more scanning so there are
potentially more failures.
Reduce the logging level to dev_dbg which is consistent with the
Freescale enetc driver.
Cc: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Jamie Iles <jamie@nuviainc.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify the comment typo: "compliment" -> "complement".
Signed-off-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It should also be regarded as an error when hw return status=4 for PF's
setting mac cmd. Only if PF return status=4 to VF should this cmd be
taken special treatment.
Fixes: 7dd29ee128 ("hinic: add sriov feature support")
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EEE should be only be enabled during stmmac_mac_link_up() when the
link are up and being set up properly. set_eee should only do settings
configuration and disabling the eee.
Without this fix, turning on EEE using ethtool will return
"Operation not supported". This is due to the driver is in a dead loop
waiting for eee to be advertised in the for eee to be activated but the
driver will only configure the EEE advertisement after the eee is
activated.
Ethtool should only return "Operation not supported" if there is no EEE
capbility in the MAC controller.
Fixes: 8a7493e58a ("net: stmmac: Fix a race in EEE enable callback")
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Acked-by: Mark Gross <mgross@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TX DMA channel data is accessed by the xrx200_start_xmit() and the
xrx200_tx_housekeeping() function from different threads. Make sure the
accesses are synchronized by acquiring the netif_tx_lock() in the
xrx200_tx_housekeeping() function too. This lock is acquired by the
kernel before calling xrx200_start_xmit().
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit