pciehp was originally introduced together with shpchp in a single
commit, c16b4b14d980 ("PCI Hotplug: Add SHPC and PCI Express hot-plug
drivers"):
https://git.kernel.org/tglx/history/c/c16b4b14d980
shpchp supports up to 31 slots per controller, hence uses separate slot
and controller structs. pciehp has a 1:1 relationship between slot and
controller and therefore never required this separation. Nevertheless,
because much of the code had been copy-pasted between the two drivers,
pciehp likewise uses separate structs to this very day.
The artificial separation of data structures adds unnecessary complexity
and bloat to pciehp and requires constantly chasing pointers at runtime.
Simplify the driver by merging struct slot into struct controller.
Merge the slot constructor pcie_init_slot() and the destructor
pcie_cleanup_slot() into the controller counterparts.
No functional change intended.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The WiGig Bus Extension (WBE) specification allows tunneling PCIe over
IEEE 802.11. A product implementing this spec is the wil6210 from
Wilocity (now part of Qualcomm Atheros). It integrates a PCIe switch
with a wireless network adapter:
00.0-+ [1ae9:0101] Upstream Port
+-00.0-+ [1ae9:0200] Downstream Port
| +-00.0 [168c:0034] Atheros AR9462 Wireless Network Adapter
+-02.0 [1ae9:0201] Downstream Port
+-03.0 [1ae9:0201] Downstream Port
Wirelessly attached devices presumably appear below the hotplug ports
with device ID [1ae9:0201]. Oddly, the Downstream Port [1ae9:0200]
leading to the wireless network adapter is likewise Hotplug Capable,
but has its Presence Detect State bit hardwired to zero. Even if the
Link Active bit is set, Presence Detect is zero, so this cannot be
caused by in-band presence detection but only by broken hardware.
pciehp assumes an empty slot if Presence Detect State is zero,
regardless of Link Active being one. Consequently, up until v4.18 it
removes the wireless network adapter in pciehp_resume(). From v4.19 it
already does so in pciehp_probe().
Be lenient towards broken hardware and assume the slot is occupied if
Link Active is set: Introduce pciehp_card_present_or_link_active()
and use it in lieu of pciehp_get_adapter_status() everywhere, except
in pciehp_handle_presence_or_link_change() whose log messages depend
on which of Presence Detect State or Link Active is set.
Remove the Presence Detect State check from __pciehp_enable_slot()
because it is only called if either of Presence Detect State or Link
Active is set.
Caution: There is a possibility that broken hardware exists which has
working Presence Detect but hardwires Link Active to one. On such
hardware the slot will now incorrectly be considered always occupied.
If such hardware is discovered, this commit can be rolled back and a
quirk can be added which sets is_hotplug_bridge = 0 for [1ae9:0200].
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200839
Reported-and-tested-by: David Yang <mmyangfl@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Rajat Jain <rajatja@google.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Now that ASPM is configured for *all* PCIe devices at boot, a problem is
seen with systems that set the FADT NO_ASPM bit. This bit indicates that
the OS should not alter the ASPM state, but when
pcie_aspm_init_link_state() runs it only checks for !aspm_support_enabled.
This misses the ACPI_FADT_NO_ASPM case because that is setting
aspm_disabled.
The result is systems may hang at boot after 1302fcf; avoidable if they
boot with pcie_aspm=off (sets !aspm_support_enabled).
Fix this by having aspm_init_link_state() check for either
!aspm_support_enabled or acpm_disabled.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=201001
Fixes: 1302fcf0d0 ("PCI: Configure *all* devices, not just hot-added ones")
Signed-off-by: Patrick Talbert <ptalbert@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Check return value of devm_pci_remap_iospace().
Addresses-Coverity-ID: 1471965 ("Unchecked return value")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Honghui Zhang <honghui.zhang@mediatek.com>
The driver does not cope with the fact that probe can fail in a number
of cases after enabling runtime PM on the device; this results in
warnings about "Unbalanced pm_runtime_enable". Furthermore if probe
fails after invoking qcom_pcie_host_init() the power-domain will be left
referenced.
As it is not possible for the error handling in qcom_pcie_host_init() to
handle errors happening after returning from that function the
pm_runtime_get_sync() is moved to qcom_pcie_probe() as well.
Fixes: 854b69efbd ("PCI: qcom: add runtime pm support to pcie_port")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
On imx7d the pcie-phy power domain is turned off in suspend and this can
make the system hang after resume when attempting any read from PCI.
Fix this by adding minimal suspend/resume code. This will prepare for
powering down on suspend and reset the block on resume.
Code is only for imx7d but a very similar sequence can be used for
other SOCs.
Original-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
[lorenzo.pieralisi@arm.com: commit log update]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
The power up defaults of the MPLL are designed for the standard 125MHz
refclock derived from the ENET PLL. As this clock has a jitter that
violates the PCIe Gen2 timing requirements, some board designs use
an external reference clock generator. Those clock generators may
output a clock at a different rate than what the MPLL expects
(usually a 100MHz clock, to re-use the PCIe bus clock).
In that case the MPLL must be reconfigured via overrides to use
different refclock dividers and loop multipliers. The i.MX6
reference manual lists both 100MHz and 200MHz as supported refclock
rates and the associated mult and div values.
Only the 100MHz setup has been tested on a real board, but since the
200MHz setup only differs in the used pre-divider it seems safe to
add it now.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Fix previous incorrect logic that limits PAXC slot number to zero only.
In order for SRIOV/VF to work, we need to allow the slot number to be
greater than zero.
Fixes: 46560388c4 ("PCI: iproc: Allow multiple devices except on PAXC")
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Dave writes:
"Various fixes, all over the place:
1) OOB data generation fix in bluetooth, from Matias Karhumaa.
2) BPF BTF boundary calculation fix, from Martin KaFai Lau.
3) Don't bug on excessive frags, to be compatible in situations mixing
older and newer kernels on each end. From Juergen Gross.
4) Scheduling in RCU fix in hv_netvsc, from Stephen Hemminger.
5) Zero keying information in TLS layer before freeing copies
of them, from Sabrina Dubroca.
6) Fix NULL deref in act_sample, from Davide Caratti.
7) Orphan SKB before GRO in veth to prevent crashes with XDP,
from Toshiaki Makita.
8) Fix use after free in ip6_xmit, from Eric Dumazet.
9) Fix VF mac address regression in bnxt_en, from Micahel Chan.
10) Fix MSG_PEEK behavior in TLS layer, from Daniel Borkmann.
11) Programming adjustments to r8169 which fix not being to enter deep
sleep states on some machines, from Kai-Heng Feng and Hans de
Goede.
12) Fix DST_NOCOUNT flag handling for ipv6 routes, from Peter
Oskolkov."
* gitolite.kernel.org:/pub/scm/linux/kernel/git/davem/net: (45 commits)
net/ipv6: do not copy dst flags on rt init
qmi_wwan: set DTR for modems in forced USB2 mode
clk: x86: Stop marking clocks as CLK_IS_CRITICAL
r8169: Get and enable optional ether_clk clock
clk: x86: add "ether_clk" alias for Bay Trail / Cherry Trail
r8169: enable ASPM on RTL8106E
r8169: Align ASPM/CLKREQ setting function with vendor driver
Revert "kcm: remove any offset before parsing messages"
kcm: remove any offset before parsing messages
net: ethernet: Fix a unused function warning.
net: dsa: mv88e6xxx: Fix ATU Miss Violation
tls: fix currently broken MSG_PEEK behavior
hv_netvsc: pair VF based on serial number
PCI: hv: support reporting serial number as slot information
bnxt_en: Fix VF mac address regression.
ipv6: fix possible use-after-free in ip6_xmit()
net: hp100: fix always-true check for link up state
ARM: dts: at91: add new compatibility string for macb on sama5d3
net: macb: disable scatter-gather for macb on sama5d3
net: mvpp2: let phylink manage the carrier state
...
Remove a set but unused variable in quirks.c. Fixes warning:
variable ‘mmio_sys_info’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Joshua Abraham <j.abraham1776@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Switch to bitmap_zalloc() to show clearly what we are allocating. Besides
that it returns pointer of bitmap type ("unsigned long *") instead of the
opaque "void *".
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pciehp's ->enable_slot, ->disable_slot, ->get_attention_status and
->reset_slot callbacks are currently implemented by wrapper functions
that do nothing else but call down to a backend function. The backends
are not called from anywhere else, so drop the wrappers and use the
backends directly as callbacks, thereby shaving off a few lines of
unnecessary code.
No functional change intended.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Drop the following includes from pciehp source files which no longer use
any of the included symbols:
* <linux/sched/signal.h> in pciehp.h
<linux/signal.h> in pciehp_hpc.c
Added by commit de25968cc8 ("fix more missing includes") to
accommodate for a call to signal_pending().
The call was removed by commit 262303fe32 ("pciehp: fix wait command
completion").
* <linux/interrupt.h> in pciehp_core.c
Added by historic commit f308a2dfbe63 ("PCI: add PCI Express Port Bus
Driver subsystem") to accommodate for a call to free_irq():
https://git.kernel.org/tglx/history/c/f308a2dfbe63
The call was removed by commit 407f452b05 ("pciehp: remove
unnecessary free_irq").
* <linux/time.h> in pciehp_core.c and pciehp_hpc.c
Added by commit 34d03419f0 ("PCIEHP: Add Electro Mechanical
Interlock (EMI) support to the PCIE hotplug driver."),
which was reverted by commit bd3d99c170 ("PCI: Remove untested
Electromechanical Interlock (EMI) support in pciehp.").
* <linux/module.h> in pciehp_ctrl.c, pciehp_hpc.c and pciehp_pci.c
Added by historic commit c16b4b14d980 ("PCI Hotplug: Add SHPC and PCI
Express hot-plug drivers"):
https://git.kernel.org/tglx/history/c/c16b4b14d980
Module-related symbols were neither used back then in those files,
nor are they used today.
* <linux/slab.h> in pciehp_ctrl.c
Added by commit 5a0e3ad6af ("include cleanup: Update gfp.h and
slab.h includes to prepare for breaking implicit slab.h inclusion from
percpu.h") to accommodate for calls to kmalloc().
The calls were removed by commit 0e94916e60 ("PCI: pciehp: Handle
events synchronously").
* "../pci.h" in pciehp_ctrl.c
Added by historic commit 67f4660b72f2 ("PCI: ASPM patch for") to
accommodate for usage of the global variable pcie_mch_quirk:
https://git.kernel.org/tglx/history/c/67f4660b72f2
The global variable was removed by commit 0ba379ec0f ("PCI: Simplify
hotplug mch quirk").
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When removing PCI devices below a hotplug bridge, pciehp marks them as
disconnected if the card is no longer present in the slot or it quiesces
them if the card is still present (by disabling INTx interrupts, bus
mastering and SERR# reporting).
To detect whether the card is still present, pciehp checks the Presence
Detect State bit in the Slot Status register. The problem with this
approach is that even if the card is present, the link to it may be
down, and it that case it would be better to mark the devices as
disconnected instead of trying to quiesce them. Moreover, if the card
in the slot was quickly replaced by another one, the Presence Detect
State bit would be set, yet trying to quiesce the new card's devices
would be wrong and the correct thing to do is to mark the previous
card's devices as disconnected.
Instead of looking at the Presence Detect State bit, it is better to
differentiate whether the card was surprise removed versus safely
removed (via sysfs or an Attention Button press). On surprise removal,
the devices should be marked as disconnected, whereas on safe removal it
is correct to quiesce the devices.
The knowledge whether a surprise removal or a safe removal is at hand
does exist further up in the call stack: A surprise removal is
initiated by pciehp_handle_presence_or_link_change(), a safe removal by
pciehp_handle_disable_request().
Pass that information down to pciehp_unconfigure_device() and use it in
lieu of the Presence Detect State bit. While there, add kernel-doc to
pciehp_unconfigure_device() and pciehp_configure_device().
Tested-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Keith Busch <keith.busch@intel.com>
Commit 89ee9f7680 ("PCI: Add device disconnected state") iterates over
the devices on a parent bus, marks each as disconnected, then marks
each device's children as disconnected using pci_walk_bus().
The same can be achieved more succinctly by calling pci_walk_bus() on
the parent bus. Moreover, this does not need to wait until acquiring
pci_lock_rescan_remove(), so move it out of that critical section.
The critical section in err.c contains a pci_dev_get() / pci_dev_put()
pair which was apparently copy-pasted from pciehp_pci.c. In the latter
it serves the purpose of holding the struct pci_dev in place until the
Command register is updated. err.c doesn't do anything like that, hence
the pair is unnecessary. Remove it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Oza Pawandeep <poza@codeaurora.org>
Cc: Sinan Kaya <okaya@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The ACPI specification allows you to provide _PXM entries for devices based
on their location on a particular bus. Let us use that if it is provided
rather than just assuming it makes sense to put the device into the
proximity domain of the root.
An example DSDT entry that will supply this is:
Device (PCI2)
{
Name (_HID, "PNP0A08") // PCI Express Root Bridge
Name (_CID, "PNP0A03") // Compatible PCI Root Bridge
Name(_SEG, 2) // Segment of this Root complex
Name(_BBN, 0xF8) // Base Bus Number
Name(_CCA, 1)
Method (_PXM, 0, NotSerialized) {
Return(0x00)
}
...
Device (BRI0) {
Name (_HID, "19E51610")
Name (_ADR, 0)
Name (_BBN, 0xF9)
Device (CAR0) {
Name (_HID, "97109912")
Name (_ADR, 0)
Method (_PXM, 0, NotSerialized) {
Return(0x02)
}
}
}
}
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Upon removal of the last device on a bus, the link_state of the bridge
leading to that bus is sought to be torn down by having pci_stop_dev()
call pcie_aspm_exit_link_state().
When ASPM was originally introduced by commit 7d715a6c1a ("PCI: add
PCI Express ASPM support"), it determined whether the device being
removed is the last one by calling list_empty() on the bridge's
subordinate devices list. That didn't work because the device is only
removed from the list slightly later in pci_destroy_dev().
Commit 3419c75e15 ("PCI: properly clean up ASPM link state on device
remove") attempted to fix it by calling list_is_last(), but that's not
correct either because it checks whether the device is at the *end* of
the list, not whether it's the last one *left* in the list. If the user
removes the device which happens to be at the end of the list via sysfs
but other devices are preceding the device in the list, the link_state
is torn down prematurely.
The real fix is to move the invocation of pcie_aspm_exit_link_state() to
pci_destroy_dev() and reinstate the call to list_empty(). Remove a
duplicate check for dev->bus->self because pcie_aspm_exit_link_state()
already contains an identical check.
Fixes: 7d715a6c1a ("PCI: add PCI Express ASPM support")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: stable@vger.kernel.org # v2.6.26
The Hyper-V host API for PCI provides a unique "serial number" which
can be used as basis for sysfs PCI slot table. This can be useful
for cases where userspace wants to find the PCI device based on
serial number.
When an SR-IOV NIC is added, the host sends an attach message
with serial number. The kernel doesn't use the serial number, but
it is useful when doing the same thing in a userspace driver such
as the DPDK. By having /sys/bus/pci/slots/N it provides a direct
way to find the matching PCI device.
There maybe some cases where serial number is not unique such
as when using GPU's. But the PCI slot infrastructure will handle
that.
This has a side effect which may also be useful. The common udev
network device naming policy uses the slot information (rather
than PCI address).
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the eetlp_prefix_path on PCIE_EXP_TYPE_RC_END devices to allow PASID
to be enabled on them. This fixes IOMMUv2 initialization on AMD Carrizo
APUs.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=201079
Fixes: 7ce3f912ae ("PCI: Enable PASID only if entire path supports End-End TLP prefixes")
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Calling into the new API to reset the secondary bus results in a deadlock.
This occurs because the device/bus is already locked at probe time.
Reverting back to the old behavior while the API is improved.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200985
Fixes: c6a44ba950 ("PCI: Rename pci_try_reset_bus() to pci_reset_bus()")
Fixes: 409888e096 ("IB/hfi1: Use pci_try_reset_bus() for initiating PCI Secondary Bus Reset")
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Cc: Sinan Kaya <okaya@codeaurora.org>
The pci_reset_bus() function calls pci_probe_reset_slot() to determine
whether to call the slot or bus reset. The check has faulty logic in that
it does not account for pci_probe_reset_slot() being able to return an
errno. Fix by only calling the slot reset when the function returns 0.
Fixes: 811c5cb37d ("PCI: Unify try slot and bus reset API")
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Cc: Sinan Kaya <okaya@codeaurora.org>
If both hot-add and power fault were observed in a single interrupt, we
handled the hot-add first, then the power fault, in this path:
pciehp_ist
if (events & (PDC | DLLSC))
pciehp_handle_presence_or_link_change
case OFF_STATE:
pciehp_enable_slot
__pciehp_enable_slot
board_added
pciehp_power_on_slot
ctrl->power_fault_detected = 0
pcie_write_cmd(ctrl, PCI_EXP_SLTCTL_PWR_ON, PCI_EXP_SLTCTL_PCC)
pciehp_green_led_on(p_slot) # power LED on
pciehp_set_attention_status(p_slot, 0) # attention LED off
if ((events & PFD) && !ctrl->power_fault_detected)
ctrl->power_fault_detected = 1
pciehp_set_attention_status(1) # attention LED on
pciehp_green_led_off(slot) # power LED off
This left the attention indicator on (even though the hot-add succeeded)
and the power indicator off (even though the slot power was on).
Fix this by checking for power faults before checking for new devices.
Prior to 0e94916e60, this was successful because everything was chained
through work queues and the order was:
INT_PRESENCE_ON -> INT_POWER_FAULT -> ENABLE_REQ
The ENABLE_REQ cleared the power fault at the end, but now everything is
handled inline with the interrupt thread, such that the work ENABLE_REQ was
doing happens before power fault handling now.
Fixes: 0e94916e60 ("PCI: pciehp: Handle events synchronously")
Signed-off-by: Keith Busch <keith.busch@intel.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
p.port can is indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/pci/switch/switchtec.c:912 ioctl_port_to_pff() warn: potential spectre issue 'pcfg->dsp_pff_inst_id' [r]
Fix this by sanitizing p.port before using it to index
pcfg->dsp_pff_inst_id
Notice that given that speculation windows are large, the policy is to kill
the speculation on the first load and not worry if it can be completed with
a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Logan Gunthorpe <logang@deltatee.com>
Cc: stable@vger.kernel.org
Merge more updates from Andrew Morton:
- the rest of MM
- procfs updates
- various misc things
- more y2038 fixes
- get_maintainer updates
- lib/ updates
- checkpatch updates
- various epoll updates
- autofs updates
- hfsplus
- some reiserfs work
- fatfs updates
- signal.c cleanups
- ipc/ updates
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (166 commits)
ipc/util.c: update return value of ipc_getref from int to bool
ipc/util.c: further variable name cleanups
ipc: simplify ipc initialization
ipc: get rid of ids->tables_initialized hack
lib/rhashtable: guarantee initial hashtable allocation
lib/rhashtable: simplify bucket_table_alloc()
ipc: drop ipc_lock()
ipc/util.c: correct comment in ipc_obtain_object_check
ipc: rename ipcctl_pre_down_nolock()
ipc/util.c: use ipc_rcu_putref() for failues in ipc_addid()
ipc: reorganize initialization of kern_ipc_perm.seq
ipc: compute kern_ipc_perm.id under the ipc lock
init/Kconfig: remove EXPERT from CHECKPOINT_RESTORE
fs/sysv/inode.c: use ktime_get_real_seconds() for superblock stamp
adfs: use timespec64 for time conversion
kernel/sysctl.c: fix typos in comments
drivers/rapidio/devices/rio_mport_cdev.c: remove redundant pointer md
fork: don't copy inconsistent signal handler state to child
signal: make get_signal() return bool
signal: make sigkill_pending() return bool
...
Allow the PCI quirk tables to be emitted in a way that avoids absolute
references to the hook functions. This reduces the size of the entries,
and, more importantly, makes them invariant under runtime relocation
(e.g., for KASLR)
Link: http://lkml.kernel.org/r/20180704083651.24360-6-ard.biesheuvel@linaro.org
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morris <james.morris@microsoft.com>
Cc: James Morris <jmorris@namei.org>
Cc: Jessica Yu <jeyu@kernel.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Nicolas Pitre <nico@linaro.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: "Serge E. Hallyn" <serge@hallyn.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Garnier <thgarnie@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Make the idle loop handle stopped scheduler tick correctly (Rafael
Wysocki).
- Prevent the menu cpuidle governor from letting CPUs spend too much
time in shallow idle states when it is invoked with scheduler tick
stopped and clean it up somewhat (Rafael Wysocki).
- Avoid invoking the platform firmware to make the platform enter
the ACPI S3 sleep state with suspended PCIe root ports which may
confuse the firmware and cause it to crash (Rafael Wysocki).
- Fix sysfs-related race in the ondemand and conservative cpufreq
governors which may cause the system to crash if the governor
module is removed during an update of CPU frequency limits (Henry
Willard).
- Select SRCU when building the system wakeup framework to avoid a
build issue in it (zhangyi).
- Make the descriptions of ACPI C-states vendor-neutral to avoid
confusion (Prarit Bhargava).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=9GrU
-----END PGP SIGNATURE-----
Merge tag 'pm-4.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"These fix the main idle loop and the menu cpuidle governor, clean up
the latter, fix a mistake in the PCI bus type's support for system
suspend and resume, fix the ondemand and conservative cpufreq
governors, address a build issue in the system wakeup framework and
make the ACPI C-states desciptions less confusing.
Specifics:
- Make the idle loop handle stopped scheduler tick correctly (Rafael
Wysocki).
- Prevent the menu cpuidle governor from letting CPUs spend too much
time in shallow idle states when it is invoked with scheduler tick
stopped and clean it up somewhat (Rafael Wysocki).
- Avoid invoking the platform firmware to make the platform enter the
ACPI S3 sleep state with suspended PCIe root ports which may
confuse the firmware and cause it to crash (Rafael Wysocki).
- Fix sysfs-related race in the ondemand and conservative cpufreq
governors which may cause the system to crash if the governor
module is removed during an update of CPU frequency limits (Henry
Willard).
- Select SRCU when building the system wakeup framework to avoid a
build issue in it (zhangyi).
- Make the descriptions of ACPI C-states vendor-neutral to avoid
confusion (Prarit Bhargava)"
* tag 'pm-4.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpuidle: menu: Handle stopped tick more aggressively
sched: idle: Avoid retaining the tick when it has been stopped
PCI / ACPI / PM: Resume all bridges on suspend-to-RAM
cpuidle: menu: Update stale polling override comment
cpufreq: governor: Avoid accessing invalid governor_data
x86/ACPI/cstate: Make APCI C1 FFH MWAIT C-state description vendor-neutral
cpuidle: menu: Fix white space
PM / sleep: wakeup: Fix build error caused by missing SRCU support
Commit 26112ddc25 (PCI / ACPI / PM: Resume bridges w/o drivers on
suspend-to-RAM) attempted to fix a functional regression resulting
from commit c62ec4610c (PM / core: Fix direct_complete handling
for devices with no callbacks) by resuming PCI bridges without
drivers (that is, "parallel PCI" ones) during system-wide suspend if
the target system state is not ACPI S0 (working state).
That turns out insufficient, however, as it is reported that, at
least in one case, the platform firmware gets confused if a PCIe
root port is suspended before entering the ACPI S3 sleep state.
That issue was exposed by commit 77b3729ca03 (PCI / PM: Use
SMART_SUSPEND and LEAVE_SUSPENDED flags for PCIe ports) that allowed
PCIe ports to stay in runtime suspend during system-wide suspend
(which is OK for suspend-to-idle, but turns out to be problematic
otherwise).
For this reason, drop the driver check from acpi_pci_need_resume()
and resume all bridges (including PCIe ports with drivers) during
system-wide suspend if the target system state is not ACPI S0.
[If the target system state is ACPI S0, it means suspend-to-idle
and the platform firmware is not going to be invoked to actually
suspend the system, so there is no need to resume the bridges in
that case.]
Fixes: 77b3729ca03 (PCI / PM: Use SMART_SUSPEND and LEAVE_SUSPENDED flags for PCIe ports)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200675
Reported-by: teika kazura <teika@gmx.com>
Tested-by: teika kazura <teika@gmx.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: 4.16+ <stable@vger.kernel.org> # 4.16+: 26112ddc25 (PCI / ACPI / PM: Resume bridges ...)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
-----BEGIN PGP SIGNATURE-----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=2Dmn
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.19-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
- Decode AER errors with names similar to "lspci" (Tyler Baicar)
- Expose AER statistics in sysfs (Rajat Jain)
- Clear AER status bits selectively based on the type of recovery (Oza
Pawandeep)
- Honor "pcie_ports=native" even if HEST sets FIRMWARE_FIRST (Alexandru
Gagniuc)
- Don't clear AER status bits if we're using the "Firmware-First"
strategy where firmware owns the registers (Alexandru Gagniuc)
- Use sysfs_match_string() to simplify ASPM sysfs parsing (Andy
Shevchenko)
- Remove unnecessary includes of <linux/pci-aspm.h> (Bjorn Helgaas)
- Defer DPC event handling to work queue (Keith Busch)
- Use threaded IRQ for DPC bottom half (Keith Busch)
- Print AER status while handling DPC events (Keith Busch)
- Work around IDT switch ACS Source Validation erratum (James
Puthukattukaran)
- Emit diagnostics for all cases of PCIe Link downtraining (Links
operating slower than they're capable of) (Alexandru Gagniuc)
- Skip VFs when configuring Max Payload Size (Myron Stowe)
- Reduce Root Port Max Payload Size if necessary when hot-adding a
device below it (Myron Stowe)
- Simplify SHPC existence/permission checks (Bjorn Helgaas)
- Remove hotplug sample skeleton driver (Lukas Wunner)
- Convert pciehp to threaded IRQ handling (Lukas Wunner)
- Improve pciehp tolerance of missed events and initially unstable
links (Lukas Wunner)
- Clear spurious pciehp events on resume (Lukas Wunner)
- Add pciehp runtime PM support, including for Thunderbolt controllers
(Lukas Wunner)
- Support interrupts from pciehp bridges in D3hot (Lukas Wunner)
- Mark fall-through switch cases before enabling -Wimplicit-fallthrough
(Gustavo A. R. Silva)
- Move DMA-debug PCI init from arch code to PCI core (Christoph
Hellwig)
- Fix pci_request_irq() usage of IRQF_ONESHOT when no handler is
supplied (Heiner Kallweit)
- Unify PCI and DMA direction #defines (Shunyong Yang)
- Add PCI_DEVICE_DATA() macro (Andy Shevchenko)
- Check for VPD completion before checking for timeout (Bert Kenward)
- Limit Netronome NFP5000 config space size to work around erratum
(Jakub Kicinski)
- Set IRQCHIP_ONESHOT_SAFE for PCI MSI irqchips (Heiner Kallweit)
- Document ACPI description of PCI host bridges (Bjorn Helgaas)
- Add "pci=disable_acs_redir=" parameter to disable ACS redirection for
peer-to-peer DMA support (we don't have the peer-to-peer support yet;
this is just one piece) (Logan Gunthorpe)
- Clean up devm_of_pci_get_host_bridge_resources() resource allocation
(Jan Kiszka)
- Fixup resizable BARs after suspend/resume (Christian König)
- Make "pci=earlydump" generic (Sinan Kaya)
- Fix ROM BAR access routines to stay in bounds and check for signature
correctly (Rex Zhu)
- Add DMA alias quirk for Microsemi Switchtec NTB (Doug Meyer)
- Expand documentation for pci_add_dma_alias() (Logan Gunthorpe)
- To avoid bus errors, enable PASID only if entire path supports
End-End TLP prefixes (Sinan Kaya)
- Unify slot and bus reset functions and remove hotplug knowledge from
callers (Sinan Kaya)
- Add Function-Level Reset quirks for Intel and Samsung NVMe devices to
fix guest reboot issues (Alex Williamson)
- Add function 1 DMA alias quirk for Marvell 88SS9183 PCIe SSD
Controller (Bjorn Helgaas)
- Remove Xilinx AXI-PCIe host bridge arch dependency (Palmer Dabbelt)
- Remove Aardvark outbound window configuration (Evan Wang)
- Fix Aardvark bridge window sizing issue (Zachary Zhang)
- Convert Aardvark to use pci_host_probe() to reduce code duplication
(Thomas Petazzoni)
- Correct the Cadence cdns_pcie_writel() signature (Alan Douglas)
- Add Cadence support for optional generic PHYs (Alan Douglas)
- Add Cadence power management ops (Alan Douglas)
- Remove redundant variable from Cadence driver (Colin Ian King)
- Add Kirin MSI support (Xiaowei Song)
- Drop unnecessary root_bus_nr setting from exynos, imx6, keystone,
armada8k, artpec6, designware-plat, histb, qcom, spear13xx (Shawn
Guo)
- Move link notification settings from DesignWare core to individual
drivers (Gustavo Pimentel)
- Add endpoint library MSI-X interfaces (Gustavo Pimentel)
- Correct signature of endpoint library IRQ interfaces (Gustavo
Pimentel)
- Add DesignWare endpoint library MSI-X callbacks (Gustavo Pimentel)
- Add endpoint library MSI-X test support (Gustavo Pimentel)
- Remove unnecessary GFP_ATOMIC from Hyper-V "new child" allocation
(Jia-Ju Bai)
- Add more devices to Broadcom PAXC quirk (Ray Jui)
- Work around corrupted Broadcom PAXC config space to enable SMMU and
GICv3 ITS (Ray Jui)
- Disable MSI parsing to work around broken Broadcom PAXC logic in some
devices (Ray Jui)
- Hide unconfigured functions to work around a Broadcom PAXC defect
(Ray Jui)
- Lower iproc log level to reduce console output during boot (Ray Jui)
- Fix mobiveil iomem/phys_addr_t type usage (Lorenzo Pieralisi)
- Fix mobiveil missing include file (Lorenzo Pieralisi)
- Add mobiveil Kconfig/Makefile support (Lorenzo Pieralisi)
- Fix mvebu I/O space remapping issues (Thomas Petazzoni)
- Use generic pci_host_bridge in mvebu instead of ARM-specific API
(Thomas Petazzoni)
- Whitelist VMD devices with fast interrupt handlers to avoid sharing
vectors with slow handlers (Keith Busch)
* tag 'pci-v4.19-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (153 commits)
PCI/AER: Don't clear AER bits if error handling is Firmware-First
PCI: Limit config space size for Netronome NFP5000
PCI/MSI: Set IRQCHIP_ONESHOT_SAFE for PCI-MSI irqchips
PCI/VPD: Check for VPD access completion before checking for timeout
PCI: Add PCI_DEVICE_DATA() macro to fully describe device ID entry
PCI: Match Root Port's MPS to endpoint's MPSS as necessary
PCI: Skip MPS logic for Virtual Functions (VFs)
PCI: Add function 1 DMA alias quirk for Marvell 88SS9183
PCI: Check for PCIe Link downtraining
PCI: Add ACS Redirect disable quirk for Intel Sunrise Point
PCI: Add device-specific ACS Redirect disable infrastructure
PCI: Convert device-specific ACS quirks from NULL termination to ARRAY_SIZE
PCI: Add "pci=disable_acs_redir=" parameter for peer-to-peer support
PCI: Allow specifying devices using a base bus and path of devfns
PCI: Make specifying PCI devices in kernel parameters reusable
PCI: Hide ACS quirk declarations inside PCI core
PCI: Delay after FLR of Intel DC P3700 NVMe
PCI: Disable Samsung SM961/PM961 NVMe before FLR
PCI: Export pcie_has_flr()
PCI: mvebu: Drop bogus comment above mvebu_pcie_map_registers()
...
-----BEGIN PGP SIGNATURE-----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=g9rD
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2018-08-15' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"This is the main drm pull request for 4.19.
Rob has some new hardware support for new qualcomm hw that I'll send
along separately. This has the display part of it, the remaining pull
is for the acceleration engine.
This also contains a wound-wait/wait-die mutex rework, Peter has acked
it for merging via my tree.
Otherwise mostly the usual level of activity. Summary:
core:
- Wound-wait/wait-die mutex rework
- Add writeback connector type
- Add "content type" property for HDMI
- Move GEM bo to drm_framebuffer
- Initial gpu scheduler documentation
- GPU scheduler fixes for dying processes
- Console deferred fbcon takeover support
- Displayport support for CEC tunneling over AUX
panel:
- otm8009a panel driver fixes
- Innolux TV123WAM and G070Y2-L01 panel driver
- Ilitek ILI9881c panel driver
- Rocktech RK070ER9427 LCD
- EDT ETM0700G0EDH6 and EDT ETM0700G0BDH6
- DLC DLC0700YZG-1
- BOE HV070WSA-100
- newhaven, nhd-4.3-480272ef-atxl LCD
- DataImage SCF0700C48GGU18
- Sharp LQ035Q7DB03
- p079zca: Refactor to support multiple panels
tinydrm:
- ILI9341 display panel
New driver:
- vkms - virtual kms driver to testing.
i915:
- Icelake:
Display enablement
DSI support
IRQ support
Powerwell support
- GPU reset fixes and improvements
- Full ppgtt support refactoring
- PSR fixes and improvements
- Execlist improvments
- GuC related fixes
amdgpu:
- Initial amdgpu documentation
- JPEG engine support on VCN
- CIK uses powerplay by default
- Move to using core PCIE functionality for gens/lanes
- DC/Powerplay interface rework
- Stutter mode support for RV
- Vega12 Powerplay updates
- GFXOFF fixes
- GPUVM fault debugging
- Vega12 GFXOFF
- DC improvements
- DC i2c/aux changes
- UVD 7.2 fixes
- Powerplay fixes for Polaris12, CZ/ST
- command submission bo_list fixes
amdkfd:
- Raven support
- Power management fixes
udl:
- Cleanups and fixes
nouveau:
- misc fixes and cleanups.
msm:
- DPU1 support display controller in sdm845
- GPU coredump support.
vmwgfx:
- Atomic modesetting validation fixes
- Support for multisample surfaces
armada:
- Atomic modesetting support completed.
exynos:
- IPPv2 fixes
- Move g2d to component framework
- Suspend/resume support cleanups
- Driver cleanups
imx:
- CSI configuration improvements
- Driver cleanups
- Use atomic suspend/resume helpers
- ipu-v3 V4L2 XRGB32/XBGR32 support
pl111:
- Add Nomadik LCDC variant
v3d:
- GPU scheduler jobs management
sun4i:
- R40 display engine support
- TCON TOP driver
mediatek:
- MT2712 SoC support
rockchip:
- vop fixes
omapdrm:
- Workaround for DRA7 errata i932
- Fix mm_list locking
mali-dp:
- Writeback implementation
PM improvements
- Internal error reporting debugfs
tilcdc:
- Single fix for deferred probing
hdlcd:
- Teardown fixes
tda998x:
- Converted to a bridge driver.
etnaviv:
- Misc fixes"
* tag 'drm-next-2018-08-15' of git://anongit.freedesktop.org/drm/drm: (1506 commits)
drm/amdgpu/sriov: give 8s for recover vram under RUNTIME
drm/scheduler: fix param documentation
drm/i2c: tda998x: correct PLL divider calculation
drm/i2c: tda998x: get rid of private fill_modes function
drm/i2c: tda998x: move mode_valid() to bridge
drm/i2c: tda998x: register bridge outside of component helper
drm/i2c: tda998x: cleanup from previous changes
drm/i2c: tda998x: allocate tda998x_priv inside tda998x_create()
drm/i2c: tda998x: convert to bridge driver
drm/scheduler: fix timeout worker setup for out of order job completions
drm/amd/display: display connected to dp-1 does not light up
drm/amd/display: update clk for various HDMI color depths
drm/amd/display: program display clock on cache match
drm/amd/display: Add NULL check for enabling dp ss
drm/amd/display: add vbios table check for enabling dp ss
drm/amd/display: Don't share clk source between DP and HDMI
drm/amd/display: Fix DP HBR2 Eye Diagram Pattern on Carrizo
drm/amd/display: Use calculated disp_clk_khz value for dce110
drm/amd/display: Implement custom degamma lut on dcn
drm/amd/display: Destroy aux_engines only once
...
- Whitelist VMD devices with fast interrupt handlers to avoid sharing
vectors with slow handlers (Keith Busch)
* remotes/lorenzo/pci/vmd:
PCI: vmd: White list for fast interrupt handlers
- Fix mvebu I/O space remapping issues (Thomas Petazzoni)
- Use generic pci_host_bridge in mvebu instead of ARM-specific API
(Thomas Petazzoni)
* remotes/lorenzo/pci/mvebu:
PCI: mvebu: Drop bogus comment above mvebu_pcie_map_registers()
PCI: mvebu: Convert to use pci_host_bridge directly
PCI: mvebu: Use resource_size() to remap I/O space
PCI: mvebu: Only remap I/O space if configured
PCI: mvebu: Fix I/O space end address calculation
PCI: mvebu: Remove redundant platform_set_drvdata() call
- Add more devices to Broadcom PAXC quirk (Ray Jui)
- Work around corrupted Broadcom PAXC config space to enable SMMU and
GICv3 ITS (Ray Jui)
- Disable MSI parsing to work around broken Broadcom PAXC logic in some
devices (Ray Jui)
- Hide unconfigured functions to work around a Broadcom PAXC defect (Ray
Jui)
- Lower iproc log level to reduce console output during boot (Ray Jui)
* remotes/lorenzo/pci/iproc:
PCI: iproc: Reduce inbound/outbound mapping print level
PCI: iproc: Reject unconfigured physical functions from PAXC
PCI: iproc: Disable MSI parsing in certain PAXC blocks
PCI: iproc: Fix up corrupted PAXC root complex config registers
PCI: iproc: Activate PAXC bridge quirk for more devices
- Remove Xilinx AXI-PCIe host bridge arch dependency (Palmer Dabbelt)
* remotes/lorenzo/pci/controller/misc:
PCI/xilinx: Depend on OF instead of the ARCH
- To avoid bus errors, enable PASID only if entire path supports End-End
TLP prefixes (Sinan Kaya)
- Unify slot and bus reset functions and remove hotplug knowledge from
callers (Sinan Kaya)
- Add Function-Level Reset quirks for Intel and Samsung NVMe devices to
fix guest reboot issues (Alex Williamson)
- Add function 1 DMA alias quirk for Marvell 88SS9183 PCIe SSD Controller
(Bjorn Helgaas)
* pci/virtualization:
PCI: Add function 1 DMA alias quirk for Marvell 88SS9183
PCI: Delay after FLR of Intel DC P3700 NVMe
PCI: Disable Samsung SM961/PM961 NVMe before FLR
PCI: Export pcie_has_flr()
PCI: Rename pci_try_reset_bus() to pci_reset_bus()
PCI: Deprecate pci_reset_bus() and pci_reset_slot() functions
PCI: Unify try slot and bus reset API
PCI: Hide pci_reset_bridge_secondary_bus() from drivers
IB/hfi1: Use pci_try_reset_bus() for initiating PCI Secondary Bus Reset
PCI: Handle error return from pci_reset_bridge_secondary_bus()
PCI/IOV: Tidy pci_sriov_set_totalvfs()
PCI: Enable PASID only if entire path supports End-End TLP prefixes
# Conflicts:
# drivers/pci/hotplug/pciehp_hpc.c
- Add DMA alias quirk for Microsemi Switchtec NTB (Doug Meyer)
- Expand documentation for pci_add_dma_alias() (Logan Gunthorpe)
* pci/switchtec:
PCI: Expand documentation for pci_add_dma_alias()
PCI: Add DMA alias quirk for Microsemi Switchtec NTB
switchtec: Use generic PCI Vendor ID and Class Code
# Conflicts:
# drivers/pci/quirks.c
- Clean up devm_of_pci_get_host_bridge_resources() resource allocation
(Jan Kiszka)
- Fixup resizable BARs after suspend/resume (Christian König)
- Make "pci=earlydump" generic (Sinan Kaya)
- Fix ROM BAR access routines to stay in bounds and check for signature
correctly (Rex Zhu)
* pci/resource:
PCI: Make pci_get_rom_size() static
PCI: Add check code for last image indicator not set
PCI: Avoid accessing memory outside the ROM BAR
PCI: Make early dump functionality generic
PCI: Cleanup PCI_REBAR_CTRL_BAR_SHIFT handling
PCI: Restore resized BAR state on resume
PCI: Clean up resource allocation in devm_of_pci_get_host_bridge_resources()
# Conflicts:
# Documentation/admin-guide/kernel-parameters.txt
- Add "pci=disable_acs_redir=" parameter to disable ACS redirection for
peer-to-peer DMA support (we don't have the peer-to-peer support yet;
this is just one piece) (Logan Gunthorpe)
* pci/peer-to-peer:
PCI: Add ACS Redirect disable quirk for Intel Sunrise Point
PCI: Add device-specific ACS Redirect disable infrastructure
PCI: Convert device-specific ACS quirks from NULL termination to ARRAY_SIZE
PCI: Add "pci=disable_acs_redir=" parameter for peer-to-peer support
PCI: Allow specifying devices using a base bus and path of devfns
PCI: Make specifying PCI devices in kernel parameters reusable
PCI: Hide ACS quirk declarations inside PCI core
- Mark fall-through switch cases before enabling -Wimplicit-fallthrough
(Gustavo A. R. Silva)
- Move DMA-debug PCI init from arch code to PCI core (Christoph Hellwig)
- Fix pci_request_irq() usage of IRQF_ONESHOT when no handler is supplied
(Heiner Kallweit)
- Unify PCI and DMA direction #defines (Shunyong Yang)
- Add PCI_DEVICE_DATA() macro (Andy Shevchenko)
- Check for VPD completion before checking for timeout (Bert Kenward)
- Limit Netronome NFP5000 config space size to work around erratum (Jakub
Kicinski)
* pci/misc:
PCI: Limit config space size for Netronome NFP5000
PCI/VPD: Check for VPD access completion before checking for timeout
PCI: Add PCI_DEVICE_DATA() macro to fully describe device ID entry
PCI: Unify PCI and normal DMA direction definitions
PCI: Use IRQF_ONESHOT if pci_request_irq() called with no handler
PCI: Call dma_debug_add_bus() for pci_bus_type from PCI core
PCI: Mark fall-through switch cases before enabling -Wimplicit-fallthrough
# Conflicts:
# drivers/pci/hotplug/pciehp_ctrl.c
- Work around IDT switch ACS Source Validation erratum (James
Puthukattukaran)
- Emit diagnostics for all cases of PCIe Link downtraining (Links
operating slower than they're capable of) (Alexandru Gagniuc)
- Skip VFs when configuring Max Payload Size (Myron Stowe)
- Reduce Root Port Max Payload Size if necessary when hot-adding a device
below it (Myron Stowe)
* pci/enumeration:
PCI: Match Root Port's MPS to endpoint's MPSS as necessary
PCI: Skip MPS logic for Virtual Functions (VFs)
PCI: Check for PCIe Link downtraining
PCI: Workaround IDT switch ACS Source Validation erratum
- Defer DPC event handling to work queue (Keith Busch)
- Use threaded IRQ for DPC bottom half (Keith Busch)
- Print AER status while handling DPC events (Keith Busch)
* pci/dpc:
PCI/DPC: Remove indirection waiting for inactive link
PCI/DPC: Use threaded IRQ for bottom half handling
PCI/DPC: Print AER status in DPC event handling
PCI/DPC: Remove rp_pio_status from dpc struct
PCI/DPC: Defer event handling to work queue
PCI/DPC: Leave interrupts enabled while handling event
- Use sysfs_match_string() to simplify ASPM sysfs parsing (Andy
Shevchenko)
- Remove unnecessary includes of <linux/pci-aspm.h> (Bjorn Helgaas)
* pci/aspm:
PCI: Remove unnecessary include of <linux/pci-aspm.h>
iwlwifi: Remove unnecessary include of <linux/pci-aspm.h>
ath9k: Remove unnecessary include of <linux/pci-aspm.h>
igb: Remove unnecessary include of <linux/pci-aspm.h>
PCI/ASPM: Convert to use sysfs_match_string() helper
- Decode AER errors with names similar to "lspci" (Tyler Baicar)
- Expose AER statistics in sysfs (Rajat Jain)
- Clear AER status bits selectively based on the type of recovery (Oza
Pawandeep)
- Honor "pcie_ports=native" even if HEST sets FIRMWARE_FIRST (Alexandru
Gagniuc)
- Don't clear AER status bits if we're using the "Firmware-First"
strategy where firmware owns the registers (Alexandru Gagniuc)
* pci/aer:
PCI/AER: Don't clear AER bits if error handling is Firmware-First
PCI/AER: Remove duplicate PCI_EXP_AER_FLAGS definition
PCI/portdrv: Remove pcie_portdrv_err_handler.slot_reset
PCI/AER: Clear device status bits during ERR_COR handling
PCI/AER: Clear device status bits during ERR_FATAL and ERR_NONFATAL
PCI/AER: Remove ERR_FATAL code from ERR_NONFATAL path
PCI/AER: Factor out ERR_NONFATAL status bit clearing
PCI/AER: Clear only ERR_NONFATAL bits during non-fatal recovery
PCI/AER: Clear only ERR_FATAL status bits during fatal recovery
PCI/AER: Honor "pcie_ports=native" even if HEST sets FIRMWARE_FIRST
PCI/AER: Add sysfs attributes for rootport cumulative stats
PCI/AER: Add sysfs attributes to provide AER stats and breakdown
PCI/AER: Define aer_stats structure for AER capable devices
PCI/AER: Move internal declarations to drivers/pci/pci.h
PCI/AER: Adopt lspci names for AER error decoding
PCI/AER: Expose internal API for obtaining AER information
# Conflicts:
# drivers/pci/pci.h
If the platform requests Firmware-First error handling, firmware is
responsible for reading and clearing AER status bits. If OSPM also clears
them, we may miss errors. See ACPI v6.2, sec 18.3.2.5 and 18.4.
This race is mostly of theoretical significance, as it is not easy to
reasonably demonstrate it in testing.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[bhelgaas: add similar guards to pci_cleanup_aer_uncorrect_error_status()
and pci_aer_clear_fatal_status()]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Like the NFP4000 and NFP6000, the NFP5000 as an erratum where reading/
writing to PCI config space addresses above 0x600 can cause the NFP to
generate PCIe completion timeouts.
Limit the NFP5000's PF's config space size to 0x600 bytes as is already
done for the NFP4000 and NFP6000.
The NFP5000's VF is 0x6003 (PCI_DEVICE_ID_NETRONOME_NFP6000_VF), the same
device ID as the NFP6000's VF. Thus, its config space is already limited
by the existing use of quirk_nfp6000().
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tony Egan <tony.egan@netronome.com>
If flag IRQCHIP_ONESHOT_SAFE isn't set for an irqchip and we have a
threaded interrupt with no primary handler, flag IRQF_ONESHOT needs to be
set for the interrupt, causing some overhead in the threaded interrupt
handler. For more detailed explanation also check following comment in
__setup_irq():
The interrupt was requested with handler = NULL, so we use the default
primary handler for it. But it does not have the oneshot flag set. In
combination with level interrupts this is deadly, because the default
primary handler just wakes the thread, then the irq lines is reenabled,
but the device still has the level irq asserted. Rinse and repeat....
While this works for edge type interrupts, we play it safe and reject
unconditionally because we can't say for sure which type this interrupt
really has. The type flags are unreliable as the underlying chip
implementation can override them.
Another comment in __setup_irq() gives a hint already that this
overhead can be avoided for PCI-MSI:
Some irq chips like MSI based interrupts are per se one shot safe. Check
the chip flags, so we can avoid the unmask dance at the end of the
threaded handler for those.
Following this let's mark all PCI-MSI irqchips as oneshot-safe.
See also discussion here:
https://lkml.kernel.org/r/alpine.DEB.2.21.1808032136490.1658@nanos.tec.linutronix.de
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously we checked the timeout before checking the VPD access completion
bit. On a very heavily loaded system this can cause VPD access to timeout.
Check the completion bit before checking the timeout.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Merge L1 Terminal Fault fixes from Thomas Gleixner:
"L1TF, aka L1 Terminal Fault, is yet another speculative hardware
engineering trainwreck. It's a hardware vulnerability which allows
unprivileged speculative access to data which is available in the
Level 1 Data Cache when the page table entry controlling the virtual
address, which is used for the access, has the Present bit cleared or
other reserved bits set.
If an instruction accesses a virtual address for which the relevant
page table entry (PTE) has the Present bit cleared or other reserved
bits set, then speculative execution ignores the invalid PTE and loads
the referenced data if it is present in the Level 1 Data Cache, as if
the page referenced by the address bits in the PTE was still present
and accessible.
While this is a purely speculative mechanism and the instruction will
raise a page fault when it is retired eventually, the pure act of
loading the data and making it available to other speculative
instructions opens up the opportunity for side channel attacks to
unprivileged malicious code, similar to the Meltdown attack.
While Meltdown breaks the user space to kernel space protection, L1TF
allows to attack any physical memory address in the system and the
attack works across all protection domains. It allows an attack of SGX
and also works from inside virtual machines because the speculation
bypasses the extended page table (EPT) protection mechanism.
The assoicated CVEs are: CVE-2018-3615, CVE-2018-3620, CVE-2018-3646
The mitigations provided by this pull request include:
- Host side protection by inverting the upper address bits of a non
present page table entry so the entry points to uncacheable memory.
- Hypervisor protection by flushing L1 Data Cache on VMENTER.
- SMT (HyperThreading) control knobs, which allow to 'turn off' SMT
by offlining the sibling CPU threads. The knobs are available on
the kernel command line and at runtime via sysfs
- Control knobs for the hypervisor mitigation, related to L1D flush
and SMT control. The knobs are available on the kernel command line
and at runtime via sysfs
- Extensive documentation about L1TF including various degrees of
mitigations.
Thanks to all people who have contributed to this in various ways -
patches, review, testing, backporting - and the fruitful, sometimes
heated, but at the end constructive discussions.
There is work in progress to provide other forms of mitigations, which
might be less horrible performance wise for a particular kind of
workloads, but this is not yet ready for consumption due to their
complexity and limitations"
* 'l1tf-final' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (75 commits)
x86/microcode: Allow late microcode loading with SMT disabled
tools headers: Synchronise x86 cpufeatures.h for L1TF additions
x86/mm/kmmio: Make the tracer robust against L1TF
x86/mm/pat: Make set_memory_np() L1TF safe
x86/speculation/l1tf: Make pmd/pud_mknotpresent() invert
x86/speculation/l1tf: Invert all not present mappings
cpu/hotplug: Fix SMT supported evaluation
KVM: VMX: Tell the nested hypervisor to skip L1D flush on vmentry
x86/speculation: Use ARCH_CAPABILITIES to skip L1D flush on vmentry
x86/speculation: Simplify sysfs report of VMX L1TF vulnerability
Documentation/l1tf: Remove Yonah processors from not vulnerable list
x86/KVM/VMX: Don't set l1tf_flush_l1d from vmx_handle_external_intr()
x86/irq: Let interrupt handlers set kvm_cpu_l1tf_flush_l1d
x86: Don't include linux/irq.h from asm/hardirq.h
x86/KVM/VMX: Introduce per-host-cpu analogue of l1tf_flush_l1d
x86/irq: Demote irq_cpustat_t::__softirq_pending to u16
x86/KVM/VMX: Move the l1tf_flush_l1d test to vmx_l1d_flush()
x86/KVM/VMX: Replace 'vmx_l1d_flush_always' with 'vmx_l1d_flush_cond'
x86/KVM/VMX: Don't set l1tf_flush_l1d to true from vmx_l1d_flush()
cpu/hotplug: detect SMT disabled by BIOS
...
In commit 27d868b5e6 ("PCI: Set MPS to match upstream bridge"), we made
sure every device's MPS setting matches its upstream bridge, making it more
likely that a hot-added device will work in a system with an optimized MPS
configuration.
Recently I've started encountering systems where the endpoint device's MPSS
capability is less than its Root Port's current MPS value, thus the
endpoint is not capable of matching its upstream bridge's MPS setting (see:
bugzilla via "Link:" below). This leaves the system vulnerable - the
upstream Root Port could respond with larger TLPs than the device can
handle, and the device will consider them to be 'Malformed'.
One could use the "pci=pcie_bus_safe" kernel parameter to work around the
issue, but that forces a user to supply a kernel parameter to get the
system to function reliably and may end up limiting MPS settings of other
unrelated, sub-topologies which could benefit from maintaining their larger
values.
Augment Keith's approach to include tuning down a Root Port's MPS setting
when its hot-added endpoint device is not capable of matching it.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200527
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jon Mason <jdmason@kudzu.us>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Sinan Kaya <okaya@kernel.org>
Cc: Dongdong Liu <liudongdong3@huawei.com>
PCIe r4.0, sec 9.3.5.4, "Device Control Register", shows both
Max_Payload_Size (MPS) and Max_Read_request_Size (MRRS) to be 'RsvdP' for
VFs. Just prior to the table it states:
"PF and VF functionality is defined in Section 7.5.3.4 except where
noted in Table 9-16. For VF fields marked 'RsvdP', the PF setting
applies to the VF."
All of which implies that with respect to Max_Payload_Size Supported
(MPSS), MPS, and MRRS values, we should not be paying any attention to the
VF's fields, but rather only to the PF's. Only looking at the PF's fields
also logically makes sense as it's the sole physical interface to the PCIe
bus.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200527
Fixes: 27d868b5e6 ("PCI: Set MPS to match upstream bridge")
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # 4.3+
Cc: Keith Busch <keith.busch@intel.com>
Cc: Sinan Kaya <okaya@kernel.org>
Cc: Dongdong Liu <liudongdong3@huawei.com>
Cc: Jon Mason <jdmason@kudzu.us>
When both ends of a PCIe Link are capable of a higher bandwidth than is
currently in use, the Link is said to be "downtrained". A downtrained Link
may indicate hardware or configuration problems in the system, but it's
hard to identify such Links from userspace.
Refactor pcie_print_link_status() so it continues to always print PCIe
bandwidth information, as several NIC drivers desire.
Add a new internal __pcie_print_link_status() to emit a message only when a
device's bandwidth is constrained by the fabric and call it from the PCI
core for all devices, which identifies all downtrained Links. It also
emits messages for a few cases that are technically not downtrained, such
as a x4 device in an open-ended x1 slot.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[bhelgaas: changelog, move __pcie_print_link_status() declaration to
drivers/pci/, rename pcie_check_upstream_link() to
pcie_report_downtraining()]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Intel Sunrise Point PCH hardware has an implementation of the ACS bits that
does not comply with the PCIe standard. Add a device-specific quirk,
pci_quirk_disable_intel_spt_pch_acs_redir() to disable ACS Redirection on
this system.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
[bhelgaas: changelog, split to separate patch]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Intel Sunrise Point (SPT) PCH hardware has an implementation of the ACS
bits that does not comply with the PCIe standard. To deal with this we
need device-specific quirks to disable ACS redirection.
Add a new pci_dev_specific_disable_acs_redir() quirk and a new
.disable_acs_redir() function pointer for use by non-compliant devices. No
functional change intended.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
[bhelgaas: split to separate patch, move
pci_dev_specific_disable_acs_redir() declarations to drivers/pci/pci.h]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Convert the search for device-specific ACS enable quirks from searching a
NULL-terminated array to iterating through the array, which is always
fixed-size anyway. No functional change intended.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
[bhelgaas: changelog, split to separate patch for reviewability]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
To support peer-to-peer traffic on a segment of the PCI hierarchy, we must
disable the ACS redirect bits for select PCI bridges. The bridges must be
selected before the devices are discovered by the kernel and the IOMMU
groups created. Therefore, add a kernel command line parameter to specify
devices which must have their ACS bits disabled.
The new parameter takes a list of devices separated by a semicolon. Each
device specified will have its ACS redirect bits disabled. This is
similar to the existing 'resource_alignment' parameter.
The ACS Request P2P Request Redirect, P2P Completion Redirect and P2P
Egress Control bits are disabled, which is sufficient to always allow
passing P2P traffic uninterrupted. The bits are set after the kernel
(optionally) enables the ACS bits itself. It is also done regardless of
whether the kernel or platform firmware sets the bits.
If the user tries to disable the ACS redirect for a device without the ACS
capability, print a warning to dmesg.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
[bhelgaas: reorder to add the generic code first and move the
device-specific quirk to subsequent patches]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Christian König <christian.koenig@amd.com>
When specifying PCI devices on the kernel command line using a
bus/device/function address, bus numbers can change when adding or
replacing a device, changing motherboard firmware, or applying kernel
parameters like "pci=assign-buses". When bus numbers change, it's likely
the command line tweak will be applied to the wrong device.
Therefore, it is useful to be able to specify devices with a base bus
number and the path of devfns needed to get to it, similar to the "device
scope" structure in the Intel VT-d spec, Section 8.3.1.
Thus, we add an option to specify devices in the following format:
[<domain>:]<bus>:<device>.<func>[/<device>.<func>]*
The path can be any segment within the PCI hierarchy of any length and
determined through the use of 'lspci -t'. When specified this way, it is
less likely that a renumbered bus will result in a valid device
specification and the tweak won't be applied to the wrong device.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
[bhelgaas: use "device" instead of "slot" in documentation since that's the
usual language in the PCI specs]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Christian König <christian.koenig@amd.com>
Separate out the code to match a PCI device with a string (typically
originating from a kernel parameter) from the
pci_specified_resource_alignment() function into its own helper function.
While we are at it, this change fixes the kernel style of the function
(fixing a number of long lines and extra parentheses).
Additionally, make the analogous change to the kernel parameter
documentation: Separate the description of how to specify a PCI device
into its own section at the head of the "pci=" parameter.
This patch should have no functional alterations.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
[bhelgaas: use "device" instead of "slot" in documentation since that's the
usual language in the PCI specs]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Christian König <christian.koenig@amd.com>
Move declarations for these functions:
pci_dev_specific_acs_enabled()
pci_dev_specific_enable_acs()
from include/linux/pci.h to drivers/pci/pci.h because nothing outside the
PCI core needs to use them.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add a device-specific reset for Intel DC P3700 NVMe device which exhibits a
timeout failure in drivers waiting for the ready status to update after
NVMe enable if the driver interacts with the device too soon after FLR. As
this has been observed in device assignment scenarios, resolve this with a
device-specific reset quirk to add an additional, heuristically determined,
delay after the FLR completes.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1592654
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The Samsung SM961/PM961 (960 EVO) sometimes fails to return from FLR with
the PCI config space reading back as -1. A reproducible instance of this
behavior is resolved by clearing the enable bit in the NVMe configuration
register and waiting for the ready status to clear (disabling the NVMe
controller) prior to FLR.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1542494
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pcie_flr() suggests pcie_has_flr() to ensure that PCIe FLR support is
present prior to calling. pcie_flr() is exported while pcie_has_flr()
is not. Resolve this.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This comment has been there since the driver was introduced, but seems
to be a leftover from previous iterations of the driver. Indeed, we do
not lookup in a list to find the register ranges that matches the
given port/lane, as the "reg" property is in each sub-node
representing a PCI port. There is no lookup involved at all.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Rather than using the ARM-specific pci_common_init_dev() API, use the
pci_host_bridge logic directly.
Unfortunately, we can't use devm_of_pci_get_host_bridge_resources(),
because the DT binding for describing PCIe apertures for this PCI
controller is a bit special, and we cannot retrieve them from the
'ranges' property. Therefore, we still have some special code to
handle this.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Instead of hardcoding the remapping of IO_SPACE_LIMIT - SZ_64K, use
resource_size().
However, we cannot use just IO_SPACE_LIMIT, because pci_ioremap_io() has
a bug and doesn't allow remapping the last 64 KB before IO_SPACE_LIMIT,
so we ensure that we do not exceed this limit. When the pci_ioremap_io()
issue is fixed, this work around can be dropped.
Note that this workaround already existed, since we were mapping only
up to IO_SPACE_LIMIT - SZ_64K.
Suggested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
[lorenzo.pieralisi@arm.com: tweaked the commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
If there is no PCI I/O aperture configured in the Device Tree, it does
not make sense to create the virtual mapping for the PCI I/O space,
since we will anyway not create the MBus window that will allow to
access it. Therefore, do the pci_ioremap_io() only if necessary.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
pcie->realio.end should be the address of last byte of the area,
therefore using resource_size() of another resource is not correct, we
must substract 1 to get the address of the last byte.
Fixes: 11be65472a ("PCI: mvebu: Adapt to the new device tree layout")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
This is already done earlier in mvebu_pcie_probe().
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Several PCI core files include pci-aspm.h even though they don't need
anything provided by that file. Remove the unnecessary includes of it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
The sysfs_match_string() helper returns index of the matching string in an
array. Use it in pcie_aspm_set_policy() to simplify the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[bhelgaas: squash sysfs_match_string() fix into original patch for issue
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
There isn't a hard dependency of the Xilinx AXI-PCIe host bridge on any
architecture. For example: at SiFive we map RISC-V cores to Xilinx FPGAs
and connect the Xilinx IP via a TileLink adapter, so the RISC-V Linux
port will need to be able to enable PCIE_XILINX in order to have PCIe
support.
This patch decouples the PCIE_XILINX support from ARCH. Instead it just
depends on OF, which is the only true dependency.
Signed-off-by: Palmer Dabbelt <palmer@dabbelt.com>
[hch: switch to OF instead of OF_PCI now that the latter is gone]
Signed-off-by: Christoph Hellwig <hch@lst.de>
[lorenzo.pieralisi@arm.com: trimmed the commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The next patch in this series will have to make the definition of
irq_cpustat_t available to entering_irq().
Inclusion of asm/hardirq.h into asm/apic.h would cause circular header
dependencies like
asm/smp.h
asm/apic.h
asm/hardirq.h
linux/irq.h
linux/topology.h
linux/smp.h
asm/smp.h
or
linux/gfp.h
linux/mmzone.h
asm/mmzone.h
asm/mmzone_64.h
asm/smp.h
asm/apic.h
asm/hardirq.h
linux/irq.h
linux/irqdesc.h
linux/kobject.h
linux/sysfs.h
linux/kernfs.h
linux/idr.h
linux/gfp.h
and others.
This causes compilation errors because of the header guards becoming
effective in the second inclusion: symbols/macros that had been defined
before wouldn't be available to intermediate headers in the #include chain
anymore.
A possible workaround would be to move the definition of irq_cpustat_t
into its own header and include that from both, asm/hardirq.h and
asm/apic.h.
However, this wouldn't solve the real problem, namely asm/harirq.h
unnecessarily pulling in all the linux/irq.h cruft: nothing in
asm/hardirq.h itself requires it. Also, note that there are some other
archs, like e.g. arm64, which don't have that #include in their
asm/hardirq.h.
Remove the linux/irq.h #include from x86' asm/hardirq.h.
Fix resulting compilation errors by adding appropriate #includes to *.c
files as needed.
Note that some of these *.c files could be cleaned up a bit wrt. to their
set of #includes, but that should better be done from separate patches, if
at all.
Signed-off-by: Nicolai Stange <nstange@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
PCI_EXP_AER_FLAGS was defined twice (with identical definitions), once
under #ifdef CONFIG_ACPI_APEI, and again at the top level. This looks like
my merge error from these commits:
fd3362cb73 ("PCI/AER: Squash aerdrv_core.c into aerdrv.c")
41cbc9eb1a ("PCI/AER: Squash ecrc.c into aerdrv.c")
Remove the duplicate PCI_EXP_AER_FLAGS definition.
Fixes: 41cbc9eb1a ("PCI/AER: Squash ecrc.c into aerdrv.c")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
On driver probe and on resume from system sleep, pciehp checks the
Presence Detect State bit in the Slot Status register to bring up an
occupied slot or bring down an unoccupied slot. Both code paths are
identical, so deduplicate them per Mika's request.
On probe, an additional check is performed to disable power of an
unoccupied slot. This can e.g. happen if power was enabled by BIOS.
It cannot happen once pciehp has taken control, hence is not necessary
on resume: The Slot Control register is set to the same value that it
had on suspend by pci_restore_state(), so if the slot was occupied,
power is enabled and if it wasn't, power is disabled. Should occupancy
have changed during the system sleep transition, power is adjusted by
bringing up or down the slot per the paragraph above.
To allow for deduplication of the presence check, move the power check
to pcie_init(). This seems safer anyway, because right now it is
performed while interrupts are already enabled, and although I can't
think of a scenario where pciehp_power_off_slot() and the IRQ thread
collide, it does feel brittle.
However this means that pcie_init() may now write to the Slot Control
register before the IRQ is requested. If both the CCIE and HPIE bits
happen to be set, pcie_wait_cmd() will wait for an interrupt (instead
of polling the Command Completed bit) and eventually emit a timeout
message. Additionally, if a level-triggered INTx interrupt is used,
the user may see a spurious interrupt splat. Avoid by disabling
interrupts before disabling power. (Normally the HPIE and CCIE bits
should be clear on probe, but conceivably they may already have been
set e.g. by BIOS.)
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Per Mika's request, add an explicit break to the last case of switch
statements everywhere in pciehp to be more defensive towards future
amendments.
Per Gustavo's request, mark all non-empty implicit fallthroughs with a
comment to silence warnings triggered by -Wimplicit-fallthrough=2.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
When a PCI device is detected, pdev->is_added is set to 1 and proc and
sysfs entries are created.
When the device is removed, pdev->is_added is checked for one and then
device is detached with clearing of proc and sys entries and at end,
pdev->is_added is set to 0.
is_added and is_busmaster are bit fields in pci_dev structure sharing same
memory location.
A strange issue was observed with multiple removal and rescan of a PCIe
NVMe device using sysfs commands where is_added flag was observed as zero
instead of one while removing device and proc,sys entries are not cleared.
This causes issue in later device addition with warning message
"proc_dir_entry" already registered.
Debugging revealed a race condition between the PCI core setting the
is_added bit in pci_bus_add_device() and the NVMe driver reset work-queue
setting the is_busmaster bit in pci_set_master(). As these fields are not
handled atomically, that clears the is_added bit.
Move the is_added bit to a separate private flag variable and use atomic
functions to set and retrieve the device addition state. This avoids the
race because is_added no longer shares a memory location with is_busmaster.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200283
Signed-off-by: Hari Vyas <hari.vyas@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Thunderbolt controllers can be runtime suspended to D3cold to save ~1.5W.
This requires that runtime D3 is allowed on its PCIe ports, so whitelist
them.
The 2015 BIOS cutoff that we've instituted for runtime D3 on PCIe ports
is unnecessary on Thunderbolt because we know that even the oldest
controller, Light Ridge (2010), is able to suspend its ports to D3 just
fine -- specifically including its hotplug ports. And the power saving
should be afforded to machines even if their BIOS predates 2015.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Andreas Noever <andreas.noever@gmail.com>
Previously we blacklisted PCIe hotplug ports for runtime D3 because:
(a) Ports handled by the firmware must not be transitioned to D3 by the
OS behind the firmware's back:
https://bugzilla.kernel.org/show_bug.cgi?id=53811
(b) Ports handled natively by the OS lacked runtime D3 support in the
pciehp driver.
We've just rectified the latter, so allow users to manually enable and
test it by passing pcie_port_pm=force on the command line. Vendors are
thus put in a position to validate hotplug ports for runtime D3 and
perhaps we can someday enable it by default, but with a BIOS cutoff date.
Ashok Raj tested runtime D3 on hotplug ports of a SkyLake Xeon-SP in
2017 and encountered Hardware Error NMIs, so this feature clearly cannot
be enabled for everyone yet:
https://lkml.kernel.org/r/20170503180426.GA4058@otc-nc-03
While at it, remove an erroneous code comment I added with 97a90aee5d
("PCI: Consolidate conditions to allow runtime PM on PCIe ports") which
claims that parents of a hotplug port must stay awake lest interrupts
cannot be delivered. That has turned out to be wrong at least for
Thunderbolt hotplug ports.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
When performing a function reset via sysfs, the device's config space is
accessed in places such as pcie_flr() and its MMIO space is accessed e.g.
in reset_ivb_igd(), so ensure accessibility by resuming the device to D0.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Ensure accessibility of a hotplug port's config space when accessed via
sysfs by resuming its parent to D0.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
pciehp's IRQ thread ensures accessibility of the port by runtime resuming
its parent to D0. However when the slot is enabled/disabled, the port
itself needs to be in D0 because its secondary bus is accessed in:
pciehp_check_link_status(),
pciehp_configure_device() (both called from board_added())
and
pciehp_unconfigure_device() (called from remove_board()).
Thus, acquire a runtime PM ref on enable/disablement of the slot.
Yinghai Lu additionally discovered that some SkyLake servers feature a
Power Controller for their PCIe hotplug ports (PCIe r3.1, sec 6.7.1.8)
which requires the port to be in D0 when invoking
pciehp_power_on_slot() (likewise called from board_added()).
If slot power is turned on while in D3hot, link training later fails:
https://lkml.kernel.org/r/20170205073454.GA253@wunner.de
The spec is silent about such a requirement, but it seems prudent to
assume that any hotplug port with a Power Controller may need this.
The present commit holds a runtime PM ref whenever slot power is turned
on and off, but it doesn't keep the port in D0 as long as slot power is
on. If vendors determine that's necessary, they need to amend pciehp to
acquire a runtime PM ref in pciehp_power_on_slot() and release one in
pciehp_power_off_slot().
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
If a hotplug port is able to send an interrupt, one would naively assume
that it is accessible at that moment. After all, if it wouldn't be
accessible, i.e. if its parent is in D3hot and the link to the hotplug
port is thus down, how should an interrupt come through?
It turns out that assumption is wrong at least for Thunderbolt: Even
though its parents are in D3hot, a Thunderbolt hotplug port is able to
signal interrupts. Because the port's config space is inaccessible and
resuming the parents may sleep, the hard IRQ handler has to defer
runtime resuming the parents and reading the Slot Status register to the
IRQ thread.
If the hotplug port uses a level-triggered INTx interrupt, it needs to
be masked until the IRQ thread has cleared the signaled events. For
simplicity, this commit also masks edge-triggered MSI/MSI-X interrupts.
Note that if the interrupt is shared (which can only happen for INTx),
other devices are starved from receiving interrupts until the IRQ thread
is scheduled, has runtime resumed the hotplug port's parents and has
read and cleared the Slot Status register.
That delay is dominated by the 10 ms D3hot->D0 transition time of each
parent port. The worst case is a Thunderbolt downstream port at the
end of a daisy chain: There may be up to six Thunderbolt controllers
in-between it and the root port, each comprising an upstream and
downstream port, plus its own upstream port. That's 13 x 10 = 130 ms.
Possible mitigations are polling the interrupt while it's disabled or
reducing the d3_delay of Thunderbolt ports if possible.
Open code masking of the interrupt instead of requesting it with the
IRQF_ONESHOT flag to minimize the period during which it is masked.
(IRQF_ONESHOT unmasks the IRQ only after the IRQ thread has finished.)
PCIe r4.0 sec 6.7.3.4 states that "If wake generation is required by the
associated form factor specification, a hotplug capable Downstream Port
must support generation of a wakeup event (using the PME mechanism) on
hotplug events that occur when the system is in a sleep state or the
Port is in device state D1, D2, or D3Hot."
This would seem to imply that PME needs to be enabled on the hotplug
port when it is runtime suspended. pci_enable_wake() currently doesn't
enable PME on bridges, it may be necessary to add an exemption for
hotplug bridges there. On "Light Ridge" Thunderbolt controllers, the
PME_Status bit is not set when an interrupt occurs while the hotplug
port is in D3hot, even if PME is enabled. (I've tested this on a Mac
and we hardcode the OSC_PCI_EXPRESS_PME_CONTROL bit to 0 on Macs in
negotiate_os_control(), modifying it to 1 didn't change the behavior.)
(Side note: Section 6.7.3.4 also states that "PME and Hot-Plug Event
interrupts (when both are implemented) always share the same MSI or
MSI-X vector". That would only seem to apply to Root Ports, however
the section never mentions Root Ports, only Downstream Ports. This is
explained in the definition of "Downstream Port" in the "Terms and
Acronyms" section of the PCIe Base Spec: "The Ports on a Switch that
are not the Upstream Port are Downstream Ports. All Ports on a Root
Complex are Downstream Ports.")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Upon resume from system sleep, the Slot Control register is written via:
pci_pm_resume_noirq()
pci_pm_default_resume_early()
pci_restore_state()
pci_restore_pcie_state()
PCIe r4.0, sec 6.7.3.2 says that after "issuing a write transaction that
targets any portion of the Port's Slot Control register, [...] software
must wait for [the] command to complete before issuing the next command".
pciehp currently fails to enforce that rule after the above-mentioned
write. Fix it.
(Moving restoration of the Slot Control register to pciehp doesn't seem
to make sense because the other PCIe hotplug drivers may need it as
well.)
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Thunderbolt hotplug ports that were occupied before system sleep resume
with their downstream link in "off" state. Only after the Thunderbolt
controller has reestablished the PCIe tunnels does the link go up.
As a result, a spurious Presence Detect Changed and/or Data Link Layer
State Changed event occurs.
The events are not immediately acted upon because tunnel reestablishment
happens in the ->resume_noirq phase, when interrupts are still disabled.
Also, notification of events may initially be disabled in the Slot
Control register when coming out of system sleep and is reenabled in the
->resume_noirq phase through:
pci_pm_resume_noirq()
pci_pm_default_resume_early()
pci_restore_state()
pci_restore_pcie_state()
It is not guaranteed that the events are acted upon at all: PCIe r4.0,
sec 6.7.3.4 says that "a port may optionally send an MSI when there are
hot-plug events that occur while interrupt generation is disabled, and
interrupt generation is subsequently enabled." Note the "optionally".
If an MSI is sent, pciehp will gratuitously turn the slot off and back
on once the ->resume_early phase has commenced.
If an MSI is not sent, the extant, unacknowledged events in the Slot
Status register will prevent future notification of presence or link
changes.
Commit 13c65840fe ("PCI: pciehp: Clear Presence Detect and Data Link
Layer Status Changed on resume") fixed the latter by clearing the events
in the ->resume phase. Move this to the ->resume_noirq phase to also
fix the gratuitous disable/enablement of the slot.
The commit further restored the Slot Control register in the ->resume
phase, but that's dispensable because as shown above it's already been
done in the ->resume_noirq phase.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Replace suspend_iter() and resume_iter() with a single function pm_iter()
to allow addition of port service callbacks for further power management
phases without having to add another iterator each time.
No functional change intended.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The ->reset_slot callback introduced by commits:
2e35afaefe ("PCI: pciehp: Add reset_slot() method") and
06a8d89af5 ("PCI: pciehp: Disable link notification across slot reset")
disables notification of Presence Detect Changed and Data Link Layer
State Changed events for the duration of a secondary bus reset.
However a bus reset not only triggers these events, but may also clear
the Presence Detect State bit in the Slot Status register and the Data
Link Layer Link Active bit in the Link Status register momentarily.
According to Sinan Kaya:
"I know for a fact that bus reset clears the Data Link Layer Active bit
as soon as link goes down. It gets set again following link up.
Presence detect depends on the HW implementation. QDT root ports
don't change presence detect for instance since nobody actually
removed the card. If an implementation supports in-band presence
detect, the answer is yes. As soon as the link goes down, presence
detect bit will get cleared until recovery."
https://lkml.kernel.org/r/42e72f83-3b24-f7ef-e5bc-290fae99259a@codeaurora.org
In-band presence detect is also covered in Table 4-15 in PCIe r4.0,
sec 4.2.6.
pciehp should therefore ensure that any parts of the driver that access
those bits do not run concurrently to a bus reset. The only precaution
the commits took to that effect was to halt interrupt polling. They
made no effort to drain the slot workqueue, cancel an outstanding
Attention Button work, or block slot enable/disable requests via sysfs
and in the ->probe hook.
Now that pciehp is converted to enable/disable the slot exclusively from
the IRQ thread, the only places accessing the two above-mentioned bits
are the IRQ thread and the ->probe hook. Add locking to serialize them
with a bus reset. This obviates the need to halt interrupt polling.
Do not add locking to the ->get_adapter_status sysfs callback to afford
users unfettered access to that bit. Use an rw_semaphore in lieu of a
regular mutex to allow parallel execution of the non-reset code paths
accessing the critical bits, i.e. the IRQ thread and the ->probe hook.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Rajat Jain <rajatja@google.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Sinan Kaya <okaya@kernel.org>
If we have a threaded interrupt with the handler being NULL, then
request_threaded_irq() -> __setup_irq() will complain and bail out if the
IRQF_ONESHOT flag isn't set. Therefore check for the handler being NULL
and set IRQF_ONESHOT in this case.
This change is needed to migrate the mei_me driver to
pci_alloc_irq_vectors() and pci_request_irq().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
There is nothing arch-specific about PCI or dma-debug, so call
dma_debug_add_bus() from the PCI core just after registering the bus type.
Most of dma-debug is already generic; this just adds reporting of pending
dma-allocations on driver unload for arches other than powerpc, sh, and
x86.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
commit 9af6bcb11e ("PCI: mobiveil: Add Mobiveil PCIe Host Bridge IP
driver") did not add the configuration and build infrastructure to
configure and build the mobiveil controller driver, so at present the
driver code is in the kernel but cannot be compiled.
Add the mobiveil controller driver Kconfig/Makefile infrastructure.
Fixes: 9af6bcb11e ("PCI: mobiveil: Add Mobiveil PCIe Host Bridge IP
driver")
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
PCI mobiveil host controller driver currently fails to compile
with the following error:
drivers/pci/controller/pcie-mobiveil.c: In function
'mobiveil_pcie_probe':
drivers/pci/controller/pcie-mobiveil.c:788:8: error: implicit
declaration of function 'devm_of_pci_get_host_bridge_resources'; did you
mean 'pci_get_host_bridge_device'?
[-Werror=implicit-function-declaration]
ret = devm_of_pci_get_host_bridge_resources(dev, 0, 0xff,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
pci_get_host_bridge_device
Add the missing include file to pull in the required function declaration.
Fixes: 9af6bcb11e ("PCI: mobiveil: Add Mobiveil PCIe Host Bridge IP
driver")
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
The field pcie_reg_base in struct mobiveil_pcie represents a physical
address so it should be of phys_addr_t type rather than void __iomem*;
this results in the following compilation warnings:
drivers/pci/controller/pcie-mobiveil.c: In function
'mobiveil_pcie_parse_dt':
drivers/pci/controller/pcie-mobiveil.c:326:22: warning: assignment makes
pointer from integer without a cast [-Wint-conversion]
pcie->pcie_reg_base = res->start;
^
drivers/pci/controller/pcie-mobiveil.c: In function
'mobiveil_pcie_enable_msi':
drivers/pci/controller/pcie-mobiveil.c:485:25: warning: initialization
makes integer from pointer without a cast [-Wint-conversion]
phys_addr_t msg_addr = pcie->pcie_reg_base;
^~~~
drivers/pci/controller/pcie-mobiveil.c: In function
'mobiveil_compose_msi_msg':
drivers/pci/controller/pcie-mobiveil.c:640:21: warning: initialization
makes integer from pointer without a cast [-Wint-conversion]
phys_addr_t addr = pcie->pcie_reg_base + (data->hwirq * sizeof(int));
Fix the type and with it the compilation warnings.
Fixes: 9af6bcb11e ("PCI: mobiveil: Add Mobiveil PCIe Host Bridge IP
driver")
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
IB_WIN_SIZE is larger than INT_MAX so we need to cast it to u64.
Fixes: 9af6bcb11e ("PCI: mobiveil: Add Mobiveil PCIe Host Bridge IP driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When an fatal error is received by a non-bridge device, the device is
removed, and pci_stop_and_remove_bus_device() deallocates the device
structure. The freed device structure is used by subsequent code to send
uevents and print messages.
Hold a reference on the device until we're finished using it. This is not
an ideal fix because pcie_do_fatal_recovery() should not use the device at
all after removing it, but that's too big a project for right now.
Fixes: 7e9084b367 ("PCI/AER: Handle ERR_FATAL with removal and re-enumeration of devices")
Signed-off-by: Thomas Tai <thomas.tai@oracle.com>
[bhelgaas: changelog, reduce get/put coverage]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
IB_WIN_SIZE is larger than INT_MAX so we need to cast it to u64.
Fixes: 9af6bcb11e ("PCI: mobiveil: Add Mobiveil PCIe Host Bridge IP driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Per PCIe r4.0, sec 6.7.3.4, a "port may optionally send an MSI when
there are hot-plug events that occur while interrupt generation is
disabled, and interrupt generation is subsequently enabled."
On probe, we currently clear all event bits in the Slot Status register
with the notable exception of the Presence Detect Changed bit. Thereby
we seek to receive an interrupt for an already occupied slot once event
notification is enabled.
But because the interrupt is optional, users may have to specify the
pciehp_force parameter on the command line, which is inconvenient.
Moreover, now that pciehp's event handling has become resilient to
missed events, a Presence Detect Changed interrupt for a slot which is
powered on is interpreted as removal of the card. If the slot has
already been brought up by the BIOS, receiving such an interrupt on
probe causes the slot to be powered off and immediately back on, which
is likewise undesirable.
Avoid both issues by making the behavior of pciehp_force the default and
clearing the Presence Detect Changed bit on probe.
Note that the stated purpose of pciehp_force per the MODULE_PARM_DESC
("Force pciehp, even if OSHP is missing") seems nonsensical because the
OSHP control method is only relevant for SHCP slots according to the
PCI Firmware specification r3.0, sec 4.8.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
A hotplug port's Slot Status register does not count how often each type
of event occurred, it only records the fact *that* an event has occurred.
Previously pciehp queued a work item for each event. But if it missed
an event, e.g. removal of a card in-between two back-to-back insertions,
it queued up the wrong work item or no work item at all. Commit
fad214b0aa ("PCI: pciehp: Process all hotplug events before looking
for new ones") sought to improve the situation by shrinking the window
during which events may be missed.
But Stefan Roese reports unbalanced Card present and Link Up events,
suggesting that we're still missing events if they occur very rapidly.
Bjorn Helgaas responds that he considers pciehp's event handling
"baroque" and calls for its simplification and rationalization:
https://lkml.kernel.org/r/20180202192045.GA53759@bhelgaas-glaptop.roam.corp.google.com
It gets worse once a hotplug port is runtime suspended: The port can
signal an interrupt while it and its parents are in D3hot, i.e. while
it is inaccessible. By the time we've runtime resumed all parents to D0
and read the port's Slot Status register, we may have missed an arbitrary
number of events. Event handling therefore needs to be reworked to
become resilient to missed events.
Assume that a Presence Detect Changed event has occurred.
Consider the following truth table:
- Slot is in OFF_STATE and is currently empty. => Do nothing.
(The event is trailing a Link Down or we've
missed an insertion and subsequent removal.)
- Slot is in OFF_STATE and is currently occupied. => Turn the slot on.
- Slot is in ON_STATE and is currently empty. => Turn the slot off.
- Slot is in ON_STATE and is currently occupied. => Turn the slot off,
(Be cautious and assume the card in then back on.
the slot isn't the same as before.)
This leads to the following simple algorithm:
1 If the slot is in ON_STATE, turn it off unconditionally.
2 If the slot is currently occupied, turn it on.
Because those actions are now carried out synchronously, rather than by
scheduled work items, pciehp reacts to the *current* situation and
missed events no longer matter.
Data Link Layer State Changed events can be handled identically to
Presence Detect Changed events. Note that in the above truth table,
a Link Up trailing a Card present event didn't have to be accounted for:
It is filtered out by pciehp_check_link_status().
As for Attention Button Pressed events, PCIe r4.0, sec 6.7.1.5 says:
"Once the Power Indicator begins blinking, a 5-second abort interval
exists during which a second depression of the Attention Button cancels
the operation." In other words, the user can only expect the system to
react to a button press after it starts blinking. Missed button presses
that occur in-between are irrelevant.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Mayurkumar Patel <mayurkumar.patel@intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
When a device is hotplugged, Presence Detect and Link Up events often do
not occur simultaneously, but with a lag of a few milliseconds. Only
the first event received is relevant, the other one can be disregarded.
Moreover, Stefan Roese reports that on certain platforms, Link State and
Presence Detect may flap for up to 100 ms before stabilizing, suggesting
that such events should be disregarded for at least this long:
https://lkml.kernel.org/r/20180130084121.18653-1-sr@denx.de
On slot enablement, pciehp_check_link_status() waits for 100 ms per
PCIe r4.0, sec 6.7.3.3, then probes the hotplugged device's vendor
register for up to 1 second.
If this succeeds, the link is definitely up, so ignore any Presence
Detect or Link State events that occurred up to this point.
pciehp_check_link_status() then checks the Link Training bit in the
Link Status register. This is the final opportunity to detect
inaccessibility of the device and abort slot enablement. Any link
or presence change that occurs afterwards will cause the slot to be
disabled again immediately after attempting to enable it.
The astute reviewer may appreciate that achieving this behavior would be
more complicated had pciehp not just been converted to enable/disable
the slot exclusively from the IRQ thread: When the slot is enabled via
sysfs, each link or presence flap would otherwise cause the IRQ thread
to run and it would have to sense that those events are belonging to a
concurrent slot enablement operation and disregard them. It would be
much more difficult than this mere 3 line change.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Stefan Roese <sr@denx.de>
No callers of pciehp_enable/disable_slot() outside of pciehp_ctrl.c
remain, so declare the functions static. For now this requires forward
declarations. Those can be eliminated by reshuffling functions once the
ongoing effort to refactor the driver has settled.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously slot enablement and disablement could happen concurrently.
But now it's under the exclusive control of the IRQ thread, rendering
the locking obsolete. Drop it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Besides the IRQ thread, there are several other places in the driver
which enable or disable the slot:
- pciehp_probe() enables the slot if it's occupied and the pciehp_force
module parameter is used.
- pciehp_resume() enables or disables the slot after system sleep.
- pciehp_queue_pushbutton_work() enables or disables the slot after the
5 second delay following an Attention Button press.
- pciehp_sysfs_enable_slot() and pciehp_sysfs_disable_slot() enable or
disable the slot on sysfs write.
This requires locking and complicates pciehp's state machine.
A simplification can be achieved by enabling and disabling the slot
exclusively from the IRQ thread.
Amend the functions listed above to request slot enable/disablement from
the IRQ thread by either synthesizing a Presence Detect Changed event or,
in the case of a disable user request (via sysfs or an Attention Button
press), submitting a newly introduced force disable request. The latter
is needed because the slot shall be forced off despite being occupied.
For this force disable request, avoid colliding with Slot Status register
bits by using a bit number greater than 16.
For synchronous execution of requests (on sysfs write), wait for the
request to finish and retrieve the result. There can only ever be one
sysfs write in flight due to the locking in kernfs_fop_write(), hence
there is no risk of returning the result of a different sysfs request to
user space.
The POWERON_STATE and POWEROFF_STATE is now no longer entered by the
above-listed functions, but solely by the IRQ thread when it begins a
power transition. Afterwards, it moves to STATIC_STATE. The same
applies to canceling the Attention Button work, it likewise becomes an
IRQ thread only operation.
An immediate consequence is that the POWERON_STATE and POWEROFF_STATE is
never observed by the IRQ thread itself, only by functions called in a
different context, such as pciehp_sysfs_enable_slot(). So remove
handling of these states from pciehp_handle_button_press() and
pciehp_handle_link_change() which are exclusively called from the IRQ
thread.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
handle_button_press_event() currently determines whether the slot has
been turned on or off by looking at the Power Controller Control bit in
the Slot Control register. This assumes that an attention button
implies presence of a power controller even though that's not mandated
by the spec. Moreover the Power Controller Control bit is unreliable
when a power fault occurs (PCIe r4.0, sec 6.7.1.8). This issue has
existed since the driver was introduced in 2004.
Fix by replacing STATIC_STATE with ON_STATE and OFF_STATE and tracking
whether the slot has been turned on or off. This is also a required
ingredient to make pciehp resilient to missed events, which is the
object of an upcoming commit.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCI hotplug core has just been refactored to separate slot
initialization for in-kernel use from publication to user space.
Take advantage of it in pciehp by publishing to user space last on
probe. This will allow enable/disablement of the slot exclusively from
the IRQ thread because the IRQ is requested after initialization for
in-kernel use (thereby getting its unique name needed by the IRQ thread)
but before user space is able to submit enable/disable requests.
On teardown, the order is the same in reverse: The user space interface
is removed prior to freeing the IRQ and destroying the slot.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When a hotplug driver calls pci_hp_register(), all steps necessary for
registration are carried out in one go, including creation of a kobject
and addition to sysfs. That's a problem for pciehp once it's converted
to enable/disable the slot exclusively from the IRQ thread: The thread
needs to be spawned after creation of the kobject (because it uses the
kobject's name), but before addition to sysfs (because it will handle
enable/disable requests submitted via sysfs).
pci_hp_deregister() does offer a ->release callback that's invoked
after deletion from sysfs and before destruction of the kobject. But
because pci_hp_register() doesn't offer a counterpart, hotplug drivers'
->probe and ->remove code becomes asymmetric, which is error prone
as recently discovered use-after-free bugs in pciehp's ->remove hook
have shown.
In a sense, this appears to be a case of the midlayer antipattern:
"The core thesis of the "midlayer mistake" is that midlayers are
bad and should not exist. That common functionality which it is
so tempting to put in a midlayer should instead be provided as
library routines which can [be] used, augmented, or ignored by
each bottom level driver independently. Thus every subsystem
that supports multiple implementations (or drivers) should
provide a very thin top layer which calls directly into the
bottom layer drivers, and a rich library of support code that
eases the implementation of those drivers. This library is
available to, but not forced upon, those drivers."
-- Neil Brown (2009), https://lwn.net/Articles/336262/
The presence of midlayer traits in the PCI hotplug core might be ascribed
to its age: When it was introduced in February 2002, the blessings of a
library approach might not have been well known:
https://git.kernel.org/tglx/history/c/a8a2069f432c
For comparison, the driver core does offer split functions for creating
a kobject (device_initialize()) and addition to sysfs (device_add()) as
an alternative to carrying out everything at once (device_register()).
This was introduced in October 2002:
https://git.kernel.org/tglx/history/c/8b290eb19962
The odd ->release callback in the PCI hotplug core was added in 2003:
https://git.kernel.org/tglx/history/c/69f8d663b595
Clearly, a library approach would not force every hotplug driver to
implement a ->release callback, but rather allow the driver to remove
the sysfs files, release its data structures and finally destroy the
kobject. Alternatively, a driver may choose to remove everything with
pci_hp_deregister(), then release its data structures.
To this end, offer drivers pci_hp_initialize() and pci_hp_add() as a
split-up version of pci_hp_register(). Likewise, offer pci_hp_del()
and pci_hp_destroy() as a split-up version of pci_hp_deregister().
Eliminate the ->release callback and move its code into each driver's
teardown routine.
Declare pci_hp_deregister() void, in keeping with the usual kernel
pattern that enablement can fail, but disablement cannot. It only
returned an error if the caller passed in a NULL pointer or a slot which
has never or is no longer registered or is sharing its name with another
slot. Those would be bugs, so WARN about them. Few hotplug drivers
actually checked the return value and those that did only printed a
useless error message to dmesg. Remove that.
For most drivers the conversion was straightforward since it doesn't
matter whether the code in the ->release callback is executed before or
after destruction of the kobject. But in the case of ibmphp, it was
unclear to me whether setting slot_cur->ctrl and slot_cur->bus_on to
NULL needs to happen before the kobject is destroyed, so I erred on
the side of caution and ensured that the order stays the same. Another
nontrivial case is pnv_php, I've found the list and kref logic difficult
to understand, however my impression was that it is safe to delete the
list element and drop the references until after the kobject is
destroyed.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com> # drivers/platform/x86
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Len Brown <lenb@kernel.org>
Cc: Scott Murray <scott@spiteful.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Gavin Shan <gwshan@linux.vnet.ibm.com>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: Corentin Chary <corentin.chary@gmail.com>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Andy Shevchenko <andy@infradead.org>
Previously the slot workqueue was used to handle events and enable or
disable the slot. That's no longer the case as those tasks are done
synchronously in the IRQ thread. The slot workqueue is thus merely used
to handle a button press after the 5 second delay and only one such work
item may be in flight at any given time. A separate workqueue isn't
necessary for this simple task, so use the system workqueue instead.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Up until now, pciehp's IRQ handler schedules a work item for each event,
which in turn schedules a work item to enable or disable the slot. This
double indirection was necessary because sleeping wasn't allowed in the
IRQ handler.
However it is now that pciehp has been converted to threaded IRQ handling
and polling, so handle events synchronously in pciehp_ist() and remove
the work item infrastructure (with the exception of work items to handle
a button press after the 5 second delay).
For link or presence change events, move the register read to determine
the current link or presence state behind acquisition of the slot lock
to prevent it from becoming stale while the lock is contended.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If the attention button is pressed to power on the slot AND the user
powers on the slot via sysfs before 5 seconds have elapsed AND powering
on the slot fails because either the slot is unoccupied OR the latch is
open, we neglect turning off the green LED so it keeps on blinking.
That's because the error path of pciehp_sysfs_enable_slot() doesn't call
pciehp_green_led_off(), unlike pciehp_power_thread() which does.
The bug has been present since 2004 when the driver was introduced.
Fix by deduplicating common code in pciehp_sysfs_enable_slot() and
pciehp_power_thread() into a wrapper function pciehp_enable_slot() and
renaming the existing function to __pciehp_enable_slot(). Same for
pciehp_disable_slot(). This will also simplify the upcoming rework of
pciehp's event handling.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We've just converted pciehp to threaded IRQ handling, but still cannot
sleep in pciehp_ist() because the function is also called in poll mode,
which runs in softirq context (from a timer).
Convert poll mode to a kthread so that pciehp_ist() always runs in task
context.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
pciehp's IRQ handler queues up a work item for each event signaled by
the hardware. A more modern alternative is to let a long running
kthread service the events. The IRQ handler's sole job is then to check
whether the IRQ originated from the device in question, acknowledge its
receipt to the hardware to quiesce the interrupt and wake up the kthread.
One benefit is reduced latency to handle the IRQ, which is a necessity
for realtime environments. Another benefit is that we can make pciehp
simpler and more robust by handling events synchronously in process
context, rather than asynchronously by queueing up work items. pciehp's
usage of work items is a historic artifact, it predates the introduction
of threaded IRQ handlers by two years. (The former was introduced in
2007 with commit 5d386e1ac4 ("pciehp: Event handling rework"), the
latter in 2009 with commit 3aa551c9b4 ("genirq: add threaded interrupt
handler support").)
Convert pciehp to threaded IRQ handling by retrieving the pending events
in pciehp_isr(), saving them for later consumption by the thread handler
pciehp_ist() and clearing them in the Slot Status register.
By clearing the Slot Status (and thereby acknowledging the events) in
pciehp_isr(), we can avoid requesting the IRQ with IRQF_ONESHOT, which
would have the unpleasant side effect of starving devices sharing the
IRQ until pciehp_ist() has finished.
pciehp_isr() does not count how many times each event occurred, but
merely records the fact *that* an event occurred. If the same event
occurs a second time before pciehp_ist() is woken, that second event
will not be recorded separately, which is problematic according to
commit fad214b0aa ("PCI: pciehp: Process all hotplug events before
looking for new ones") because we may miss removal of a card in-between
two back-to-back insertions. We're about to make pciehp_ist() resilient
to missed events. The present commit regresses the driver's behavior
temporarily in order to separate the changes into reviewable chunks.
This doesn't affect regular slow-motion hotplug, only plug-unplug-plug
operations that happen in a timespan shorter than wakeup of the IRQ
thread.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Mayurkumar Patel <mayurkumar.patel@intel.com>
Cc: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Document the driver's data structures to lower the barrier to entry for
contributors.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Since commit 0f4bd8014d ("PCI: hotplug: Drop checking of PCI_BRIDGE_
CONTROL in *_unconfigure_device()"), pciehp_unconfigure_device() can no
longer fail, so declare it and its sole caller remove_board() void, in
keeping with the usual kernel pattern that enablement can fail, but
disablement cannot. No functional change intended.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
pciehp_disable_slot() checks if the ctrl attribute of the slot is NULL
and bails out if so. However the function is not called prior to the
attribute being set in pcie_init_slot(), and pcie_init_slot() is not
called if ctrl is NULL. So the check is unnecessary. Drop it.
It has been present ever since the driver was introduced in 2004, but it
was already unnecessary back then:
https://git.kernel.org/tglx/history/c/c16b4b14d980
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit b440bde74f ("PCI: Add pci_ignore_hotplug() to ignore hotplug
events for a device") iterates over the devices on a hotplug port's
subordinate bus in pciehp's IRQ handler without acquiring pci_bus_sem.
It is thus possible for a user to cause a crash by concurrently
manipulating the device list, e.g. by disabling slot power via sysfs
on a different CPU or by initiating a remove/rescan via sysfs.
This can't be fixed by acquiring pci_bus_sem because it may sleep.
The simplest fix is to avoid the list iteration altogether and just
check the ignore_hotplug flag on the port itself. This works because
pci_ignore_hotplug() sets the flag both on the device as well as on its
parent bridge.
We do lose the ability to print the name of the device blocking hotplug
in the debug message, but that's probably bearable.
Fixes: b440bde74f ("PCI: Add pci_ignore_hotplug() to ignore hotplug events for a device")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
When pciehp is unbound (e.g. on unplug of a Thunderbolt device), the
hotplug_slot struct is deregistered and thus freed before freeing the
IRQ. The IRQ handler and the work items it schedules print the slot
name referenced from the freed structure in various informational and
debug log messages, each time resulting in a quadruple dereference of
freed pointers (hotplug_slot -> pci_slot -> kobject -> name).
At best the slot name is logged as "(null)", at worst kernel memory is
exposed in logs or the driver crashes:
pciehp 0000:10:00.0:pcie204: Slot((null)): Card not present
An attacker may provoke the bug by unplugging multiple devices on a
Thunderbolt daisy chain at once. Unplugging can also be simulated by
powering down slots via sysfs. The bug is particularly easy to trigger
in poll mode.
It has been present since the driver's introduction in 2004:
https://git.kernel.org/tglx/history/c/c16b4b14d980
Fix by rearranging teardown such that the IRQ is freed first. Run the
work items queued by the IRQ handler to completion before freeing the
hotplug_slot struct by draining the work queue from the ->release_slot
callback which is invoked by pci_hp_deregister().
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v2.6.4
If addition of sysfs files fails on registration of a hotplug slot, the
struct pci_slot as well as the entry in the slot_list is leaked. The
issue has been present since the hotplug core was introduced in 2002:
https://git.kernel.org/tglx/history/c/a8a2069f432c
Perhaps the idea was that even though sysfs addition fails, the slot
should still be usable. But that's not how drivers use the interface,
they abort probe if a non-zero value is returned.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v2.4.15+
Cc: Greg Kroah-Hartman <greg@kroah.com>
Ten years ago, commit 58319b802a ("PCI: Hotplug core: remove 'name'")
dropped the name element from struct hotplug_slot but neglected to update
the skeleton driver.
That same year, commit f46753c5e3 ("PCI: introduce pci_slot") raised the
number of arguments to pci_hp_register() from one to four.
Fourteen years ago, historic commit 7ab60fc1b8e7 ("PCI Hotplug skeleton:
final cleanups") removed all usages of the retval variable from
pcihp_skel_init() but not the variable itself, provoking a compiler
warning: https://git.kernel.org/tglx/history/c/7ab60fc1b8e7
It seems fair to assume the driver hasn't been used as a template for a new
driver in a while. Per Bjorn's and Christoph's preference, delete it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Christoph Hellwig <hch@lst.de>
The pci_error_handlers.slot_reset() callback is only used for non-bridge
devices (see broadcast_error_message()). Since portdrv only binds to
bridges, we don't need pcie_portdrv_slot_reset(), so remove it.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: changelog, remove pcie_portdrv_slot_reset() completely]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In case of correctable error, the Correctable Error Detected bit in the
Device Status register is set. Clear it after handling the error.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Clear the device status bits while handling both ERR_FATAL and ERR_NONFATAL
cases.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: rename to pci_aer_clear_device_status(), declare internal to PCI
core instead of exposing it everywhere]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
broadcast_error_message() is only used for ERR_NONFATAL events, when the
state is always pci_channel_io_normal, so remove the unused alternate path.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
aer_error_resume() clears all ERR_NONFATAL error status bits. This is
exactly what pci_cleanup_aer_uncorrect_error_status(), so use that instead
of duplicating the code.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: split to separate patch]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_cleanup_aer_uncorrect_error_status() is called by driver .slot_reset()
methods when handling ERR_NONFATAL errors. Previously this cleared *all*
the bits, including ERR_FATAL bits.
Since we're only handling ERR_NONFATAL errors, clear only the ERR_NONFATAL
error status bits.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: split to separate patch]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
During recovery from fatal errors, we previously called
pci_cleanup_aer_uncorrect_error_status(), which cleared *all* uncorrectable
error status bits (both ERR_FATAL and ERR_NONFATAL).
Instead, call a new pci_aer_clear_fatal_status() that clears only the
ERR_FATAL bits (as indicated by the PCI_ERR_UNCOR_SEVER register).
Based-on-patch-by: Oza Pawandeep <poza@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Now that the old implementation of pci_reset_bus() is gone, replace
pci_try_reset_bus() with pci_reset_bus().
Compared to the old implementation, new code will fail immmediately with
-EAGAIN if object lock cannot be obtained.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_reset_bus() and pci_reset_slot() functions are not being used by any
code. Remove them from the kernel in favor of pci_try_reset_bus() and
pci_try_reset_slot() functions.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Drivers are expected to call pci_try_reset_slot() or pci_try_reset_bus() by
querying if a system supports hotplug or not. A survey showed that most
drivers don't do this and we are leaking hotplug capability to the user.
Hide pci_try_slot_reset() from drivers and embed into pci_try_bus_reset().
Change pci_try_reset_bus() parameter from struct pci_bus to struct pci_dev.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Rename pci_reset_bridge_secondary_bus() to pci_bridge_secondary_bus_reset()
and move the declaration from linux/pci.h to drivers/pci.h to be used
internally in PCI directory only.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit 01fd61c0b9 ("PCI: Add a return type for
pci_reset_bridge_secondary_bus()") added a return value to the function to
return if a device is accessible following a reset. Callers are not
checking the value.
Pass error code up high in the stack if device is not accessible.
Fixes: 01fd61c0b9 ("PCI: Add a return type for pci_reset_bridge_secondary_bus()")
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Simplify waiting for the contained link to become inactive, removing the
indirection to a unnecessary DPC-specific handler.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
Remove the work struct that was being used to handle a DPC event and use a
threaded IRQ instead.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
A DPC enabled device suppresses ERR_(NON)FATAL messages, preventing the AER
handler from reporting error details. If the DPC trigger reason says the
downstream port detected the error, collect the AER uncorrectable status
for logging, then clear the status.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
We don't need to save the rp pio status across multiple contexts as all
DPC event handling occurs in a single work queue context.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
Move all event handling to the existing work queue, which will
make it simpler to pass event information to the handler.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
Now that the DPC driver clears the interrupt status before exiting the
IRQ handler, we don't need to abuse the DPC control register to know if
a shared interrupt is for a new DPC event: a DPC port can not trigger
a second interrupt until the host clears the trigger status later in the
work queue handler.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
According to the documentation, "pcie_ports=native", linux should use
native AER and DPC services. While that is true for the _OSC method
parsing, this is not the only place that is checked. Should the HEST
list PCIe ports as firmware-first, linux will not use native services.
This happens because aer_acpi_firmware_first() doesn't take 'pcie_ports'
into account. This is wrong. DPC uses the same logic when it decides
whether to load or not, so fixing this also fixes DPC not loading.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[bhelgaas: return "false" from bool function (from kbuild robot)]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add sysfs attributes for rootport statistics (that are cumulative of all
the ERR_* messages seen on this PCI hierarchy).
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add sysfs attributes to provide total and breakdown of the AERs seen,
into different type of correctable, fatal and nonfatal errors:
/sys/bus/pci/devices/<dev>/aer_dev_correctable
/sys/bus/pci/devices/<dev>/aer_dev_fatal
/sys/bus/pci/devices/<dev>/aer_dev_nonfatal
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Define a structure to hold the AER statistics. There are 2 groups of
statistics: dev_* counters that are to be collected for all AER capable
devices and rootport_* counters that are collected for all (AER capable)
rootports only. Allocate and free this structure when device is added or
released (thus counters survive the lifetime of the device).
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Since pci_aer_init() and pci_no_aer() are used only internally, move their
declarations to the PCI internal header file. Also, no one cares about
return value of pci_aer_init(), so make it void.
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
lspci uses abbreviated naming for AER error strings. Adopt the same naming
convention for the AER printing so they match.
Signed-off-by: Tyler Baicar <tbaicar@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
Export some common AER functions and structures for other PCI core drivers
to use. Since this is making the function externally visible inside the
PCI core, prepend "aer_" to the function name.
Signed-off-by: Keith Busch <keith.busch@intel.com>
[bhelgaas: move AER declarations from linux/aer.h to drivers/pci/pci.h]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
Add pci_epc_set_msi() maximum 32 interrupts validation.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Add MSI-X support and update driver documentation accordingly.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Cleanup PCI_ENDPOINT_TEST memspace (by moving the interrupt number away
from command section).
Add IRQ_TYPE register to identify the triggered ID interrupt required
for the READ/WRITE/COPY tests and raise IRQ test commands.
Update documentation accordingly.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Currently DesignWare IP does not handle legacy interrupts.
Add a legacy interrupt callback handler.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Remove duplicate defines located on pcie-designware.h file already
available on /include/uapi/linux/pci-regs.h file.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Add PCIe config space capability search function.
Add sysfs set/get interface to allow the change of EP MSI-X maximum number.
Add EP MSI-X callback for triggering interruptions.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Change {cdns, dra7xx, artpec6, dw, rockchip}_pcie_ep_raise_irq() and
pci_epc_raise_irq() signature, namely the interrupt_num variable type
from u8 to u16 to accommodate 2048 maximum MSI-X interrupts.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Alan Douglas <adouglas@cadence.com>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Joao Pinto <jpinto@synopsys.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Move specific features settings from EP shared code
(pcie-designware-ep.c) to the driver (pcie-designware-plat.c).
Previous implementation disables the EP link notification
by default for all SoCs that uses EP DesignWare IP, which affects
directly the dra7xx and artpec6 SoCs.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Variable mmc is being assigned but is never used hence it is redundant
and can be removed.
Cleans up clang warning:
warning: variable 'mmc' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
[lorenzo.pieralisi@arm.com: reworked commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Alan Douglas <adouglas@cadence.com>
Function dw_pcie_host_init() already initializes the root_bus_nr field
of 'struct pcie_port', so the -1 assignment prior to calling
dw_pcie_host_init() in platform specific driver is not really needed.
Drop it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
Function dw_pcie_host_init() already initializes the root_bus_nr field
of 'struct pcie_port', so the -1 assignment prior to calling
dw_pcie_host_init() in platform specific driver is not really needed.
Drop it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Function dw_pcie_host_init() already initializes the root_bus_nr field
of 'struct pcie_port', so the -1 assignment prior to calling
dw_pcie_host_init() in platform specific driver is not really needed.
Drop it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jianguo Sun <sunjianguo1@huawei.com>
Function dw_pcie_host_init() already initializes the root_bus_nr field
of 'struct pcie_port', so the -1 assignment prior to calling
dw_pcie_host_init() in platform specific driver is not really needed.
Drop it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Joao Pinto <Joao.Pinto@synopsys.com>
Function dw_pcie_host_init() already initializes the root_bus_nr field
of 'struct pcie_port', so the -1 assignment prior to calling
dw_pcie_host_init() in platform specific driver is not really needed.
Drop it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Function dw_pcie_host_init() already initializes the root_bus_nr field
of 'struct pcie_port', so the -1 assignment prior to calling
dw_pcie_host_init() in platform specific driver is not really needed.
Drop it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Function dw_pcie_host_init() already initializes the root_bus_nr field
of 'struct pcie_port', so the -1 assignment prior to calling
dw_pcie_host_init() in platform specific driver is not really needed.
Drop it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Function dw_pcie_host_init() already initializes the root_bus_nr field
of 'struct pcie_port', so the -1 assignment prior to calling
dw_pcie_host_init() in platform specific driver is not really needed.
Drop it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Function dw_pcie_host_init() already initializes the root_bus_nr field
of 'struct pcie_port', so the -1 assignment prior to calling
dw_pcie_host_init() in platform specific driver is not really needed.
Drop it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Reduce inbound/outbound mapping print level from dev_info() to
dev_dbg(). This reduces the console logs during Linux boot process.
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
PAXC is an emulated PCIe root complex internally in various Broadcom
based SoCs. PAXC internally connects to the embedded network processor
within these SoCs, with the embedeed network processor exposed as an
endpoint device.
The number of physical functions from the embedded network processor
that can be accessed depends on the firmware configuration.
Unfortunately, due to an ASIC bug, unconfigured physical functions cannot
be properly hidden from the root complex during enumerattion. As a
result, config write access to these unconfigured physical functions
during enumeration will cause a bus lock up on the embedded network
processor.
Fortunately, these unconfigured physical functions contain a very
specific, staled PCIe device ID 0x168e. By making use of this device ID,
one is able to terminate the enumeration early in the vendor/device ID
config read.
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
The internal MSI parsing logic in certain revisions of PAXC root
complexes does not work properly and can cause corruptions on the
writes transactions so they need to be disabled.
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
On certain versions of Broadcom PAXC based root complexes, certain
regions of the configuration space are corrupted. As a result, it
prevents the Linux PCIe stack from traversing the linked list of the
capability registers completely and therefore the root complex is
not advertised as "PCIe capable". This prevents the correct PCIe RID
from being parsed in the kernel PCIe stack. A correct RID is required
for mapping to a stream ID from the SMMU or the device ID from the
GICv3 ITS.
This patch fixes up the issue by manually populating the related
PCIe capabilities.
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
Activate PAXC bridge quirk for more PAXC based PCIe root complex with
the following PCIe device ID:
0xd750, 0xd802, 0xd804
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Warning level 2 was used: -Wimplicit-fallthrough=2
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Some IDT switches incorrectly flag an ACS Source Validation error on
completions for config read requests even though PCIe r4.0, sec 6.12.1.1,
says that completions are never affected by ACS Source Validation. Here's
the text of IDT 89H32H8G3-YC, erratum #36:
Item #36 - Downstream port applies ACS Source Validation to Completions
Section 6.12.1.1 of the PCI Express Base Specification 3.1 states that
completions are never affected by ACS Source Validation. However,
completions received by a downstream port of the PCIe switch from a
device that has not yet captured a PCIe bus number are incorrectly
dropped by ACS Source Validation by the switch downstream port.
Workaround: Issue a CfgWr1 to the downstream device before issuing the
first CfgRd1 to the device. This allows the downstream device to capture
its bus number; ACS Source Validation no longer stops completions from
being forwarded by the downstream port. It has been observed that
Microsoft Windows implements this workaround already; however, some
versions of Linux and other operating systems may not.
When doing the first config read to probe for a device, if the device is
behind an IDT switch with this erratum:
1. Disable ACS Source Validation if enabled
2. Wait for device to become ready to accept config accesses (by using
the Config Request Retry Status mechanism)
3. Do a config write to the endpoint
4. Enable ACS Source Validation (if it was enabled to begin with)
The workaround suggested by IDT is basically only step 3, but we don't know
when the device is ready to accept config requests. That means we need to
do config reads until we receive a non-Config Request Retry Status, which
means we need to disable ACS SV temporarily.
Signed-off-by: James Puthukattukaran <james.puthukattukaran@oracle.com>
[bhelgaas: changelog, clean up whitespace, fold in unused variable fix
from Anders Roxell <anders.roxell@linaro.org>]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Add shutdown callback to host driver which will disable PHY and
PM runtime.
Signed-off-by: Alan Douglas <adouglas@cadence.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
These PM ops will enable/disable the optional PHYs if present. The
AXI link-down register in the host driver is now cleared in
cdns_pci_map_bus() since the link-down bit will be set if the PHY has
been disabled. It is not cleared when enabling the PHY, since the
link will not yet be up (e.g. when an EP controller is connected
back-to-back to the host controller and its PHY is still disabled).
Link: http://lkml.kernel.org/r/1529915453-4633-5-git-send-email-adouglas@cadence.com
Signed-off-by: Alan Douglas <adouglas@cadence.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Add support for MSI to the kirin host controller driver, based
on the generic dwc infrastructure.
Signed-off-by: Xiaowei Song <songxiaowei@hisilicon.com>
Signed-off-by: Yao Chen <chenyao11@huawei.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
If PHYs are present, initialize and enable them at driver probe.
Signed-off-by: Alan Douglas <adouglas@cadence.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
cdns_pcie_writel() writes a long value; change the value parameter type
from u16 to u32 to rectify the function signature and related behaviour.
Signed-off-by: Alan Douglas <adouglas@cadence.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
commit ef1433f717 ("PCI: endpoint: Create configfs entry for each
pci_epf_device_id table entry") while adding configfs entry for each
pci_epf_device_id table entry introduced a NULL pointer dereference error
when CONFIG_PCI_ENDPOINT_CONFIGFS is not enabled.
Fix it here.
Fixes: ef1433f717 ("PCI: endpoint: Create configfs entry for each
pci_epf_device_id table entry")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[lorenzo.pieralisi: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit de0aa7b2f9 ("PCI: hv: Fix 2 hang issues in hv_compose_msi_msg()")
uses local_bh_disable()/enable(), because hv_pci_onchannelcallback() can
also run in tasklet context as the channel event callback, so bottom halves
should be disabled to prevent a race condition.
With CONFIG_PROVE_LOCKING=y in the recent mainline, or old kernels that
don't have commit f71b74bca6 ("irq/softirqs: Use lockdep to assert IRQs
are disabled/enabled"), when the upper layer IRQ code calls
hv_compose_msi_msg() with local IRQs disabled, we'll see a warning at the
beginning of __local_bh_enable_ip():
IRQs not enabled as expected
WARNING: CPU: 0 PID: 408 at kernel/softirq.c:162 __local_bh_enable_ip
The warning exposes an issue in de0aa7b2f97d: local_bh_enable() can
potentially call do_softirq(), which is not supposed to run when local IRQs
are disabled. Let's fix this by using local_irq_save()/restore() instead.
Note: hv_pci_onchannelcallback() is not a hot path because it's only called
when the PCI device is hot added and removed, which is infrequent.
Fixes: de0aa7b2f9 ("PCI: hv: Fix 2 hang issues in hv_compose_msi_msg()")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Cc: stable@vger.kernel.org
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
-----BEGIN PGP SIGNATURE-----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=IOF/
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.18-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- Fix a use-after-free in the endpoint code (Dan Carpenter)
- Stop defaulting CONFIG_PCIE_DW_PLAT_HOST to yes (Geert Uytterhoeven)
- Fix an nfp regression caused by a change in how we limit the number
of VFs we can enable (Jakub Kicinski)
- Fix failure path cleanup issues in the new R-Car gen3 PHY support
(Marek Vasut)
- Fix leaks of OF nodes in faraday, xilinx-nwl, xilinx (Nicholas Mc
Guire)
* tag 'pci-v4.18-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
nfp: stop limiting VFs to 0
PCI/IOV: Reset total_VFs limit after detaching PF driver
PCI: faraday: Add missing of_node_put()
PCI: xilinx-nwl: Add missing of_node_put()
PCI: xilinx: Add missing of_node_put()
PCI: endpoint: Use after free in pci_epf_unregister_driver()
PCI: controller: dwc: Do not let PCIE_DW_PLAT_HOST default to yes
PCI: rcar: Clean up PHY init on failure
PCI: rcar: Shut the PHY down in failpath
Part of advk_pcie_probe() is exactly an open-coded version of
pci_host_probe(). So instead of duplicating this code, use
pci_host_probe() directly.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The PCIE I/O and MEM resource allocation mechanism is that root bus
goes through the following steps:
1. Check PCI bridges' range and computes I/O and Mem base/limits.
2. Sort all subordinate devices I/O and MEM resource requirements and
allocate the resources and writes/updates subordinate devices'
requirements to PCI bridges I/O and Mem MEM/limits registers.
Currently, PCI Aardvark driver only handles the second step and lacks
the first step, so there is an I/O and MEM resource allocation failure
when using a PCI switch. This commit fixes that by sizing bridges
before doing the resource allocation.
Fixes: 8c39d71036 ("PCI: aardvark: Add Aardvark PCI host controller
driver")
Signed-off-by: Zachary Zhang <zhangzg@marvell.com>
[Thomas: edit commit log.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: <stable@vger.kernel.org>
So drivers can use them. This can be used to replace
duplicate code in the drm subsystem.
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It is reported that commit c62ec4610c (PM / core: Fix direct_complete
handling for devices with no callbacks) introduced a system suspend
regression on Samsung 305V4A by allowing a PCI bridge (not a PCIe
port) to stay in D3 over suspend-to-RAM, which is a side effect of
setting power.direct_complete for the children of that bridge that
have no PM callbacks.
On the majority of systems PCI bridges are not allowed to be
runtime-suspended (the power/control sysfs attribute is set to "on"
for them by default), but user space can change that setting and if
it does so and a given bridge has no children with PM callbacks, the
direct_complete optimization will be applied to it and it will stay
in suspend over system suspend. Apparently, that confuses the
platform firmware on the affected machine and that may very well
happen elsewhere, so avoid the direct_complete optimization for
PCI bridges with no drivers (if there is a driver, it should take
care of the PM handling) on suspend-to-RAM altogether (that should
not matter for suspend-to-idle as platform firmware is not involved
in it).
Fixes: c62ec4610c (PM / core: Fix direct_complete handling for devices with no callbacks)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=199941
Reported-by: n0000b.n000b@gmail.com
Tested-by: n0000b.n000b@gmail.com
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: 4.15+ <stable@vger.kernel.org> # 4.15+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
A PCIe endpoint carries the process address space identifier (PASID) in
the TLP prefix as part of the memory read/write transaction. The address
information in the TLP is relevant only for a given PASID context.
An IOMMU takes PASID value and the address information from the
TLP to look up the physical address in the system.
PASID is an End-End TLP Prefix (PCIe r4.0, sec 6.20). Sec 2.2.10.2 says
It is an error to receive a TLP with an End-End TLP Prefix by a
Receiver that does not support End-End TLP Prefixes. A TLP in
violation of this rule is handled as a Malformed TLP. This is a
reported error associated with the Receiving Port (see Section 6.2).
Prevent error condition by proactively requiring End-End TLP prefix to be
supported on the entire data path between the endpoint and the root port
before enabling PASID.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Seeing there's been some confusion about the use of pci_add_dma_alias(),
expand the comment to describe why it must be called early and how
early it must be called.
Also, expand on the purpose of this function and common reasons it would
be used.
[The comment was reworded to some extent by Alex Williamson]
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Doug Meyer <dmeyer@gigaio.com>
pci_get_rom_size() is called only from pci_map_rom(), so it can be static.
Make it static and remove the declaration from include/linux/pci.h.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If the "last image" indicator was not set in the PCI data struct, print "No
more image in the PCI ROM" instead of looping back and printing "Invalid
PCI ROM header signature".
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
pci_get_rom_size() accepts the base and size of the ROM BAR as arguments.
The byte at "rom + size" is the first byte *past* the ROM, so change ">" to
">=" to avoid accessing beyond the actual length of the ROM BAR.
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Add a quirk for the Microsemi Switchtec parts to allow DMA access via
non-transparent bridging to work when the IOMMU is turned on.
This exclusively addresses the ability of a remote NT endpoint to perform
DMA accesses through the locally enumerated NT endpoint. Other aspects of
the Switchtec NTB functionality, such as interrupts for doorbells and
messages are independent of this quirk, and will work whether the IOMMU is
on or off.
When a requestor on one NT endpoint accesses memory on another NT endpoint,
it does this via a devfn proxy ID. Proxy IDs are statically assigned to
each NT endpoint by the NTB hardware as part of the release-from-reset
sequence prior to PCI enumeration. These proxy IDs cannot be modified
dynamically, and are not visible to the host during enumeration.
When the Switchtec NTB driver loads it will map local requestor IDs, such
as the root complex and transparent bridge DMA engines, to proxy IDs by
populating those requestor IDs in hardware mapping table table entries.
This establishes a fixed relationship between a requestor ID and a proxy
ID.
When a peer on a remote NT endpoint performs an access within a particular
translation window in it's NT endpoint BAR address space, that access is
translated to a DMA request on the local endpoint's bus. As part of the
translation process, the original requestor ID has its devfn replaced with
the proxy ID, and the bus portion of the BDF is replaced with the bus of
the local NT endpoint. Thus, the DMA access from a remote NT endpoint will
appear on the local bus to have come from the unknown devfn which the IOMMU
will reject.
Interrogate NTB hardware registers for each remote NT endpoint to obtain
the proxy IDs that have been assigned to it and alias them to the local
(enumerated) NT endpoint's device. The IOMMU then accepts the remote proxy
IDs as if they were requests coming directly from the enumerated endpoint,
giving remote requestors access to memory resources which the local host
has made available.
Note that the aliasing of the proxy IDs cannot be performed at the driver
level given the current IOMMU architecture. Superficially this is because
pci_add_dma_alias() symbol is not exported. Functionally, the current
IOMMU design requires the aliasing to be performed prior to the creation of
IOMMU groups. If a driver were to attempt to use pci_add_dma_alias() in
its probe routine it would fail since the IOMMU groups have been set up by
that time. If the Switchtec hardware supported dynamic proxy ID
(re-)assignment this would be an issue, but it does not.
To further clarify static proxy ID assignment: While the requester ID to
proxy ID mapping can be dynamically changed, the number and value of proxy
IDs given to an NT EP cannot, even for dynamic reconfiguration such as
hot-add. Therefore, the chip configuration must account a priori for the
proxy IDs needs, considering both static and dynamic system configurations.
For example, a port on the chip may not having anything plugged into it at
start of day; but it must have a sufficient number of proxy IDs assigned to
accommodate the supported devices which may be hot-added.
Switchtec NTB functionality with the IOMMU off is unchanged by this quirk.
Signed-off-by: Doug Meyer <dmeyer@gigaio.com>
[bhelgaas: use hard-coded Device IDs instead of adding #defines for each]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Move the Microsemi Switchtec PCI Vendor ID (same as
PCI_VENDOR_ID_PMC_Sierra) to pci_ids.h. Also, replace Microsemi class
constants with the standard PCI definitions.
Signed-off-by: Doug Meyer <dmeyer@gigaio.com>
[bhelgaas: restore SPDX (I assume it was removed by mistake), remove
device ID definitions]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Move early dump functionality into common code so that it is available for
all architectures. No need to carry arch-specific reads around as the read
hooks are already initialized by the time pci_setup_device() is getting
called during scan.
Tested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cleanup PCI_REBAR_CTRL_BAR_SHIFT handling. That was hard coded instead of
properly defined in the header for some reason.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Resize BARs after resume to the expected size again.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199959
Fixes: d6895ad39f ("drm/amdgpu: resize VRAM BAR for CPU access v6")
Fixes: 276b738deb ("PCI: Add resizable BAR infrastructure")
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v4.15+
The TotalVFs register in the SR-IOV capability is the hardware limit on the
number of VFs. A PF driver can limit the number of VFs further with
pci_sriov_set_totalvfs(). When the PF driver is removed, reset any VF
limit that was imposed by the driver because that limit may not apply to
other drivers.
Before 8d85a7a4f2 ("PCI/IOV: Allow PF drivers to limit total_VFs to 0"),
pci_sriov_set_totalvfs(pdev, 0) meant "we can enable TotalVFs virtual
functions", and the nfp driver used that to remove the VF limit when the
driver unloads.
8d85a7a4f2 broke that because instead of removing the VF limit,
pci_sriov_set_totalvfs(pdev, 0) actually sets the limit to zero, and that
limit persists even if another driver is loaded.
We could fix that by making the nfp driver reset the limit when it unloads,
but it seems more robust to do it in the PCI core instead of relying on the
driver.
The regression scenario is:
nfp_pci_probe (driver 1)
...
nfp_pci_remove
pci_sriov_set_totalvfs(pf->pdev, 0) # limits VFs to 0
...
nfp_pci_probe (driver 2)
nfp_rtsym_read_le("nfd_vf_cfg_max_vfs")
# no VF limit from firmware
Now driver 2 is broken because the VF limit is still 0 from driver 1.
Fixes: 8d85a7a4f2 ("PCI/IOV: Allow PF drivers to limit total_VFs to 0")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
[bhelgaas: changelog, rename functions]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The call to of_get_next_child() returns a node pointer with refcount
incremented thus it must be explicitly decremented here in the error
path and after the last usage.
Fixes: d3c68e0a7e ("PCI: faraday: Add Faraday Technology FTPCI100 PCI Host Bridge driver")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The call to of_get_next_child() returns a node pointer with
refcount incremented thus it must be explicitly decremented
here after the last usage.
Fixes: ab597d35ef ("PCI: xilinx-nwl: Add support for Xilinx NWL PCIe Host Controller")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The call to of_get_next_child() returns a node pointer with refcount
incremented thus it must be explicitly decremented here after the last
usage.
Fixes: 8961def568 ("PCI: xilinx: Add Xilinx AXI PCIe Host Bridge IP driver")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
[lorenzo.pieralisi@arm.com: reworked commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We need to use list_for_each_entry_safe() because the
pci_ep_cfs_remove_epf_group() function frees "group".
Fixes: ef1433f717 ("PCI: endpoint: Create configfs entry for each pci_epf_device_id table entry")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
PCIE_DW_PLAT_HOST does not have any platform dependency, so it should
not default to yes.
Fixes: 1d906b2207 ("PCI: dwc: Add support for EP mode")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
If the Gen3 PHY fails to power up, the code does not undo the
initialization caused by phy_init(). Add the missing failure
handling to the rcar_pcie_phy_init_gen3() function.
Fixes: 517ca93a71 ("PCI: rcar: Add R-Car gen3 PHY support")
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
If anything fails past phy_init_fn() and the system is a Gen3 with
a PHY, the PHY will be left on and inited. This is caused by the
phy_init_fn, which is in fact a pointer to rcar_pcie_phy_init_gen3()
function, which starts the PHY, yet has no counterpart in the failpath.
Add that counterpart.
Fixes: 517ca93a71 ("PCI: rcar: Add R-Car gen3 PHY support")
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
new_pcichild_device() is not called in atomic context.
The call chain ending up at new_pcichild_device() is:
[1] new_pcichild_device() <- pci_devices_present_work()
pci_devices_present_work() is only set in INIT_WORK().
Despite never getting called from atomic context,
new_pcichild_device() calls kzalloc with GFP_ATOMIC,
which waits busily for allocation.
GFP_ATOMIC is not necessary and can be replaced with GFP_KERNEL
to avoid busy waiting.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
[lorenzo.pieralisi@arm.com: reworked commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Devices with slow interrupt handlers are significantly harming
performance when their interrupt vector is shared with a fast device.
Create a class code white list for devices with known fast interrupt
handlers and let all other devices share a single vector so that they
don't interfere with performance.
At the moment, only the NVM Express class code is on the list, but more
may be added if VMD users desire to use other low-latency devices in
these domains.
Signed-off-by: Keith Busch <keith.busch@intel.com>
[lorenzo.pieralisi@arm.com: changelog]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Jon Derrick: <jonathan.derrick@intel.com>
Outbound window is used to translate CPU space addresses to PCIe space
addresses when the CPU initiates PCIe transactions.
According to the suggestion of the HW designers, the recommended
solution is to use the default outbound parameters, even though the
current outbound window setting does not cause any known functional
issue.
This patch doesn't address any known functional issue, but aligns to
HW design guidelines, and removes code that isn't needed.
Signed-off-by: Evan Wang <xswang@marvell.com>
[Thomas: tweak commit log.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
[lorenzo.pieralisi@arm.com: handled host->controller dir move]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Victor Gu <xigu@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
In other to mimic other PCIe host controller drivers, introduce an
advk_pcie_valid_device() helper, used in the configuration read/write
functions.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
[lorenzo.pieralisi@arm.com: updated host->controller dir move]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The shpchp driver registers for all PCI bridge devices. Its probe method
should fail if either (1) the bridge doesn't have an SHPC or (2) the OS
isn't allowed to use it (the platform firmware may be operating the SHPC
itself).
Separate these two tests into:
- A new shpc_capable() that looks for the SHPC hardware and is applicable
on all systems (ACPI and non-ACPI), and
- A simplified acpi_get_hp_hw_control_from_firmware() that we call only
when we already know an SHPC exists and there may be ACPI methods to
either request permission to use it (_OSC) or transfer control to the
OS (OSHP).
acpi_get_hp_hw_control_from_firmware() is implemented when CONFIG_ACPI=y,
but does nothing if the current platform doesn't support ACPI.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Commit 51bc085d64 ("PCI: Improve host drivers compile test coverage")
added configuration options to allow PCI host controller drivers to be
compile tested on all architectures.
Some host controller drivers (eg PCIE_ALTERA) config entries select the
PCI_DOMAINS config option to enable PCI domains management in the kernel.
Now that host controller drivers can be compiled on all architectures, this
triggers build regressions on arches that do not implement the PCI_DOMAINS
required API (ie pci_domain_nr()):
drivers/ata/pata_ali.c: In function 'ali_init_chipset':
drivers/ata/pata_ali.c:469:38: error: implicit declaration of function 'pci_domain_nr'; did you mean 'pci_iomap_wc'?
Furthemore, some software configurations (ie Jailhouse) require a
PCI_DOMAINS enabled kernel to configure multiple host controllers without
having an explicit dependency on the ARM platform on which they run.
Make PCI_DOMAINS a visible configuration option on ARM so that software
configurations that need it can manually select it and move the PCI_DOMAINS
selection from PCI controllers configuration file to ARM sub-arch config
entries that currently require it, fixing the issue.
Fixes: 51bc085d64 ("PCI: Improve host drivers compile test coverage")
Link: https://lkml.kernel.org/r/20180612170229.GA10141@roeck-us.net
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Acked-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Ley Foon Tan <ley.foon.tan@intel.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Scott Branden <scott.branden@broadcom.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Guenter Roeck <linux@roeck-us.net>
The endpoint library must be initialized before its users, which are in
drivers/pci/controllers. The endpoint initialization currently depends on
link order.
This corrects a kernel crash when loading the Cadence EP driver, since it
calls devm_pci_epc_create() and this is only valid once the endpoint
library has been initialized.
Fixes: 6e0832fa43 ("PCI: Collect all native drivers under drivers/pci/controller/")
Signed-off-by: Alan Douglas <adouglas@cadence.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
An SHPC can be operated either by platform firmware or by the OS. The OS
uses a host bridge ACPI _OSC method to negotiate for control of SHPC. If
firmware wants to prevent an OS from operating an SHPC, it must supply an
_OSC method that declines to grant SHPC ownership to the OS.
If acpi_pci_find_root() returns NULL, it means there's no ACPI host bridge
device (PNP0A03 or PNP0A08) and hence no _OSC method, so the OS is always
allowed to manage the SHPC.
Fix a NULL pointer dereference when CONFIG_ACPI=y but the current
hardware/firmware platform doesn't support ACPI. In that case,
acpi_get_hp_hw_control_from_firmware() is implemented but
acpi_pci_find_root() returns NULL.
Fixes: 90cc0c3cc7 ("PCI: shpchp: Add shpchp_is_native()")
Link: https://lkml.kernel.org/r/20180621164715.28160-1-marc.zyngier@arm.com
Reported-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Instead of first allocating and then freeing memory for struct resource in
case we cannot parse a PCI resource from the device tree, work against a
local struct and kmemdup() it when we decide to go with it.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
- Additional struct_size() conversions (Matthew, Kees)
- Explicitly reported overflow fixes (Silvio, Kees)
- Add missing kvcalloc() function (Kees)
- Treewide conversions of allocators to use either 2-factor argument
variant when available, or array_size() and array3_size() as needed (Kees)
-----BEGIN PGP SIGNATURE-----
Comment: Kees Cook <kees@outflux.net>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=zUUp
-----END PGP SIGNATURE-----
Merge tag 'overflow-v4.18-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull more overflow updates from Kees Cook:
"The rest of the overflow changes for v4.18-rc1.
This includes the explicit overflow fixes from Silvio, further
struct_size() conversions from Matthew, and a bug fix from Dan.
But the bulk of it is the treewide conversions to use either the
2-factor argument allocators (e.g. kmalloc(a * b, ...) into
kmalloc_array(a, b, ...) or the array_size() macros (e.g. vmalloc(a *
b) into vmalloc(array_size(a, b)).
Coccinelle was fighting me on several fronts, so I've done a bunch of
manual whitespace updates in the patches as well.
Summary:
- Error path bug fix for overflow tests (Dan)
- Additional struct_size() conversions (Matthew, Kees)
- Explicitly reported overflow fixes (Silvio, Kees)
- Add missing kvcalloc() function (Kees)
- Treewide conversions of allocators to use either 2-factor argument
variant when available, or array_size() and array3_size() as needed
(Kees)"
* tag 'overflow-v4.18-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (26 commits)
treewide: Use array_size in f2fs_kvzalloc()
treewide: Use array_size() in f2fs_kzalloc()
treewide: Use array_size() in f2fs_kmalloc()
treewide: Use array_size() in sock_kmalloc()
treewide: Use array_size() in kvzalloc_node()
treewide: Use array_size() in vzalloc_node()
treewide: Use array_size() in vzalloc()
treewide: Use array_size() in vmalloc()
treewide: devm_kzalloc() -> devm_kcalloc()
treewide: devm_kmalloc() -> devm_kmalloc_array()
treewide: kvzalloc() -> kvcalloc()
treewide: kvmalloc() -> kvmalloc_array()
treewide: kzalloc_node() -> kcalloc_node()
treewide: kzalloc() -> kcalloc()
treewide: kmalloc() -> kmalloc_array()
mm: Introduce kvcalloc()
video: uvesafb: Fix integer overflow in allocation
UBIFS: Fix potential integer overflow in allocation
leds: Use struct_size() in allocation
Convert intel uncore to struct_size
...
- squash AER directory into drivers/pci/pcie/aer.c (Bjorn Helgaas)
* pci/aer-squash:
PCI/AER: Use "PCI Express" consistently in Kconfig text
PCI/AER: Hoist aerdrv.c, aer_inject.c up to drivers/pci/pcie/
PCI/AER: Squash Kconfig.debug into Kconfig
PCI/AER: Move private AER things to aerdrv.c
PCI/AER: Move aer_irq() declaration to portdrv.h
PCI/AER: Move pcie_aer_get_firmware_first() to portdrv.h
PCI/AER: Remove duplicate pcie_port_bus_type declaration
PCI/AER: Squash ecrc.c into aerdrv.c
PCI/AER: Squash aerdrv_acpi.c into aerdrv.c
PCI/AER: Squash aerdrv_errprint.c into aerdrv.c
PCI/AER: Squash aerdrv_core.c into aerdrv.c
PCI/AER: Reorder code to group probe/remove stuff together
PCI/AER: Remove forward declarations
Use "PCI Express" consistently in Kconfig text. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Hoist aerdrv.c, aer_inject.c up to drivers/pci/pcie/ so they're next to
other PCIe service drivers. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Most of the things in aerdrv.h are only used in aerdrv.c, so move them
there. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
The aer_irq() declaration is the only thing needed by aer_inject.c. Move
it to portdrv.h so we eventually get rid of aerdrv.h completely. No
functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Move pcie_aer_get_firmware_first() to portdrv.h, where it can be more
easily shared between AER and DPC. Then DPC no longer needs to include
aer/aerdrv.h. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
pcie_port_bus_type is already declared in portdrv.h, so remove the
unnecessary duplicate declaration in aerdrv.h. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reorder code to group probe/remove stuff together. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Native PCI drivers for root complex devices were originally all in
drivers/pci/host/. Some of these devices can also be operated in endpoint
mode. Drivers for endpoint mode didn't seem to fit in the "host"
directory, so we put both the root complex and endpoint drivers in
per-device directories, e.g., drivers/pci/dwc/, drivers/pci/cadence/, etc.
These per-device directories contain trivial Kconfig and Makefiles and
clutter drivers/pci/. Make a new drivers/pci/controllers/ directory and
collect all the device-specific drivers there.
No functional change intended.
Link: https://lkml.kernel.org/r/1520304202-232891-1-git-send-email-shawn.lin@rock-chips.com
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
-----BEGIN PGP SIGNATURE-----
iQJIBAABCgAyFiEEgMe7l+5h9hnxdsnuWYigwDrT+vwFAlsZdg0UHGJoZWxnYWFz
QGdvb2dsZS5jb20ACgkQWYigwDrT+vwJOBAAsuuWsOdiJRRhQLU5WfEMFgzcL02R
gsumqZkK7E8LOq0DPNMtcgv9O0KgYZyCiZyTMJ8N7sEYohg04lMz8mtYXOibjcwI
p+nVMko8jQXV9FXwSMGVqigEaLLcrbtkbf/mPriD63DDnRMa/+/Jh15SwfLTydIH
QRTJbIxkS3EiOauj5C8QY3UwzjlvV9mDilzM/x+MSK27k2HFU9Pw/3lIWHY716rr
grPZTwBTfIT+QFZjwOm6iKzHjxRM830sofXARkcH4CgSNaTeq5UbtvAs293MHvc+
v/v/1dfzUh00NxfZDWKHvTUMhjazeTeD9jEVS7T+HUcGzvwGxMSml6bBdznvwKCa
46ynePOd1VcEBlMYYS+P4njRYBLWeUwt6/TzqR4yVwb0keQ6Yj3Y9H2UpzscYiCl
O+0qz6RwyjKY0TpxfjoojgHn4U5ByI5fzVDJHbfr2MFTqqRNaabVrfl6xU4sVuhh
OluT5ym+/dOCTI/wjlolnKNb0XThVre8e2Busr3TRvuwTMKMIWqJ9sXLovntdbqE
furPD/UnuZHkjSFhQ1SQwYdWmsZI5qAq2C9haY8sEWsXEBEcBGLJ2BEleMxm8UsL
KXuy4ER+R4M+sFtCkoWf3D4NTOBUdPHi4jyk6Ooo1idOwXCsASVvUjUEG5YcQC6R
kpJ1VPTKK1XN64I=
=aFAi
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.18-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- unify AER decoding for native and ACPI CPER sources (Alexandru
Gagniuc)
- add TLP header info to AER tracepoint (Thomas Tai)
- add generic pcie_wait_for_link() interface (Oza Pawandeep)
- handle AER ERR_FATAL by removing and re-enumerating devices, as
Downstream Port Containment does (Oza Pawandeep)
- factor out common code between AER and DPC recovery (Oza Pawandeep)
- stop triggering DPC for ERR_NONFATAL errors (Oza Pawandeep)
- share ERR_FATAL recovery path between AER and DPC (Oza Pawandeep)
- disable ASPM L1.2 substate if we don't have LTR (Bjorn Helgaas)
- respect platform ownership of LTR (Bjorn Helgaas)
- clear interrupt status in top half to avoid interrupt storm (Oza
Pawandeep)
- neaten pci=earlydump output (Andy Shevchenko)
- avoid errors when extended config space inaccessible (Gilles Buloz)
- prevent sysfs disable of device while driver attached (Christoph
Hellwig)
- use core interface to report PCIe link properties in bnx2x, bnxt_en,
cxgb4, ixgbe (Bjorn Helgaas)
- remove unused pcie_get_minimum_link() (Bjorn Helgaas)
- fix use-before-set error in ibmphp (Dan Carpenter)
- fix pciehp timeouts caused by Command Completed errata (Bjorn
Helgaas)
- fix refcounting in pnv_php hotplug (Julia Lawall)
- clear pciehp Presence Detect and Data Link Layer Status Changed on
resume so we don't miss hotplug events (Mika Westerberg)
- only request pciehp control if we support it, so platform can use
ACPI hotplug otherwise (Mika Westerberg)
- convert SHPC to be builtin only (Mika Westerberg)
- request SHPC control via _OSC if we support it (Mika Westerberg)
- simplify SHPC handoff from firmware (Mika Westerberg)
- fix an SHPC quirk that mistakenly included *all* AMD bridges as well
as devices from any vendor with device ID 0x7458 (Bjorn Helgaas)
- assign a bus number even to non-native hotplug bridges to leave
space for acpiphp additions, to fix a common Thunderbolt xHCI
hot-add failure (Mika Westerberg)
- keep acpiphp from scanning native hotplug bridges, to fix common
Thunderbolt hot-add failures (Mika Westerberg)
- improve "partially hidden behind bridge" messages from core (Mika
Westerberg)
- add macros for PCIe Link Control 2 register (Frederick Lawler)
- replace IB/hfi1 custom macros with PCI core versions (Frederick
Lawler)
- remove dead microblaze and xtensa code (Bjorn Helgaas)
- use dev_printk() when possible in xtensa and mips (Bjorn Helgaas)
- remove unused pcie_port_acpi_setup() and portdrv_acpi.c (Bjorn
Helgaas)
- add managed interface to get PCI host bridge resources from OF (Jan
Kiszka)
- add support for unbinding generic PCI host controller (Jan Kiszka)
- fix memory leaks when unbinding generic PCI host controller (Jan
Kiszka)
- request legacy VGA framebuffer only for VGA devices to avoid false
device conflicts (Bjorn Helgaas)
- turn on PCI_COMMAND_IO & PCI_COMMAND_MEMORY in pci_enable_device()
like everybody else, not in pcibios_fixup_bus() (Bjorn Helgaas)
- add generic enable function for simple SR-IOV hardware (Alexander
Duyck)
- use generic SR-IOV enable for ena, nvme (Alexander Duyck)
- add ACS quirk for Intel 7th & 8th Gen mobile (Alex Williamson)
- add ACS quirk for Intel 300 series (Mika Westerberg)
- enable register clock for Armada 7K/8K (Gregory CLEMENT)
- reduce Keystone "link already up" log level (Fabio Estevam)
- move private DT functions to drivers/pci/ (Rob Herring)
- factor out dwc CONFIG_PCI Kconfig dependencies (Rob Herring)
- add DesignWare support to the endpoint test driver (Gustavo
Pimentel)
- add DesignWare support for endpoint mode (Gustavo Pimentel)
- use devm_ioremap_resource() instead of devm_ioremap() in dra7xx and
artpec6 (Gustavo Pimentel)
- fix Qualcomm bitwise NOT issue (Dan Carpenter)
- add Qualcomm runtime PM support (Srinivas Kandagatla)
- fix DesignWare enumeration below bridges (Koen Vandeputte)
- use usleep() instead of mdelay() in endpoint test (Jia-Ju Bai)
- add configfs entries for pci_epf_driver device IDs (Kishon Vijay
Abraham I)
- clean up pci_endpoint_test driver (Gustavo Pimentel)
- update Layerscape maintainer email addresses (Minghuan Lian)
- add COMPILE_TEST to improve build test coverage (Rob Herring)
- fix Hyper-V bus registration failure caused by domain/serial number
confusion (Sridhar Pitchai)
- improve Hyper-V refcounting and coding style (Stephen Hemminger)
- avoid potential Hyper-V hang waiting for a response that will never
come (Dexuan Cui)
- implement Mediatek chained IRQ handling (Honghui Zhang)
- fix vendor ID & class type for Mediatek MT7622 (Honghui Zhang)
- add Mobiveil PCIe host controller driver (Subrahmanya Lingappa)
- add Mobiveil MSI support (Subrahmanya Lingappa)
- clean up clocks, MSI, IRQ mappings in R-Car probe failure paths
(Marek Vasut)
- poll more frequently (5us vs 5ms) while waiting for R-Car data link
active (Marek Vasut)
- use generic OF parsing interface in R-Car (Vladimir Zapolskiy)
- add R-Car V3H (R8A77980) "compatible" string (Sergei Shtylyov)
- add R-Car gen3 PHY support (Sergei Shtylyov)
- improve R-Car PHYRDY polling (Sergei Shtylyov)
- clean up R-Car macros (Marek Vasut)
- use runtime PM for R-Car controller clock (Dien Pham)
- update arm64 defconfig for Rockchip (Shawn Lin)
- refactor Rockchip code to facilitate both root port and endpoint
mode (Shawn Lin)
- add Rockchip endpoint mode driver (Shawn Lin)
- support VMD "membar shadow" feature (Jon Derrick)
- support VMD bus number offsets (Jon Derrick)
- add VMD "no AER source ID" quirk for more device IDs (Jon Derrick)
- remove unnecessary host controller CONFIG_PCIEPORTBUS Kconfig
selections (Bjorn Helgaas)
- clean up quirks.c organization and whitespace (Bjorn Helgaas)
* tag 'pci-v4.18-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (144 commits)
PCI/AER: Replace struct pcie_device with pci_dev
PCI/AER: Remove unused parameters
PCI: qcom: Include gpio/consumer.h
PCI: Improve "partially hidden behind bridge" log message
PCI: Improve pci_scan_bridge() and pci_scan_bridge_extend() doc
PCI: Move resource distribution for single bridge outside loop
PCI: Account for all bridges on bus when distributing bus numbers
ACPI / hotplug / PCI: Drop unnecessary parentheses
ACPI / hotplug / PCI: Mark stale PCI devices disconnected
ACPI / hotplug / PCI: Don't scan bridges managed by native hotplug
PCI: hotplug: Add hotplug_is_native()
PCI: shpchp: Add shpchp_is_native()
PCI: shpchp: Fix AMD POGO identification
PCI: mobiveil: Add MSI support
PCI: mobiveil: Add Mobiveil PCIe Host Bridge IP driver
PCI/AER: Decode Error Source Requester ID
PCI/AER: Remove aer_recover_work_func() forward declaration
PCI/DPC: Use the generic pcie_do_fatal_recovery() path
PCI/AER: Pass service type to pcie_do_fatal_recovery()
PCI/DPC: Disable ERR_NONFATAL handling by DPC
...
- support VMD "membar shadow" feature (Jon Derrick)
- support VMD bus number offsets (Jon Derrick)
- add VMD "no AER source ID" quirk for more device IDs (Jon Derrick)
* lorenzo/pci/vmd:
PCI: vmd: Add an additional VMD device id to driver device id table
x86/PCI: Add additional VMD device root ports to VMD AER quirk
PCI: vmd: Add offset to bus numbers if necessary
PCI: vmd: Assign membar addresses from shadow registers
PCI: Add Intel VMD devices to pci ids
Lukas Wunner